idatastart HC Document number Revision Date

Size: px
Start display at page:

Download "idatastart HC Document number Revision Date"

Transcription

1 PRODUCT guide idatastart HC Document number Revision Date NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

2 GETTING ED Page 2 of WeLcome Congratulations on the purchase of your idatastart HC solution. You are now a few simple steps away from enjoying your new remote starter unit with enhanced features. Before starting your installation, please ensure that your idatastart HC module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. table of contents Box Contents 3 Module Pinout 4 Tach Programming Procedure 5 Remote Programming Procedure 6 Valet Mode Programming Procedure 7 Compatible Accessories 9 Online Module Settings 10 Module Diagnostics 11 Remote Starter Error Codes 12 need HeLP? Module Reset Procedure support@idatalink.com idatalink.com/support idatastart HC

3 BOX CTENTS - 1 OF 1 Page 3 of BOX CTENTS HC MODULE 2-WAY REMOTE - TR2350AC HC2 - HC2352AC M1-8 PIN BLACK AUTOMATIC TRANSMISSI CUT LOOP M2-12 PIN BLACK M3-10 PIN WHITE TELEMATIC 1-4 PIN BLUE TELEMATIC 2-4 PIN RED NC - 4 PIN RED M5-6 PIN BLUE M4-20 PIN BLACK NC - 3 PIN BLACK PROGRAMMING BUTT 1-WAY REMOTE - TR1150A HC2 - HC2351AC LED 1 LED 2 RF PORT/WEBLINK PORT - 4 PIN BLACK USB ANTENNA - AN2300A ANTENNA CABLE HC1 - HC1151AC ANTENNA LED HOOD SWITCH M5 M4 M3 M2 M1 ANTENNA BUTT HCF - HCF900A RF PORT - 4 PIN BLACK RF DECODER - FT-D100 RF DECODER CABLE 2 PIN BLACK RF PORT - 4 PIN BLACK HCX - HCX000A STICKERS 6 PIN WHITE OR BLUE ANTENNA RF PORT - 4 PIN WHITE idatastart HC

4 MODULE PINOUT - 1 OF 1 Page 4 of HC MODULE M1 01 ORANGE - ESSORY (+) 02 RED - POWER (30A) 03 PURPLE - ER (+) 04 PINK/WHITE - PROG. RELAY #4 - IGNITI 2 (+) (DEFAULT) 05 PINK - IGNITI (+) 06 WHITE - PROG. RELAY #5 (10A) - PARKING LIGHTS (+) (DEFAULT) 07 RED - POWER (30A) 08 BLACK - GROUND M M2 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK RELEASE (-) OUTPUT 04 GREEN/WHITE BLACK DOT - ARM (-) OUTPUT 05 GREEN/BLACK BLACK DOT - DISARM (-) OUTPUT 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE BLACK DOT - POC 1-2ND UNLOCK OTHER DOORS (-) OUTPUT 09 PURPLE/BLACK BLACK DOT - POC 2 - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK BLACK DOT - POC 3 - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT - POC 4 - ER KILL (-) OUTPUT 12 WHITE BLACK DOT - PARKING LIGHTS (-) OUTPUT AUTOMATIC TRANSMISSI CUT LOOP M2 M3 M5 M M3 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT - E-BRAKE (-) INPUT 03 PURPLE SILVER DOT - DOOR (+) INPUT 04 GREEN SILVER DOT - DOOR (-) INPUT 05 PURPLE/WHITE SILVER DOT - TACH (-) INPUT 06 WHITE/BLUE SILVER DOT - X-TRIGGER (-) INPUT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT - TRUNK (-) INPUT 09 GRAY/BLACK SILVER DOT - GLOW PLUG (+) INPUT 10 EMPTY M FUNCTIS DEFINED BY FIRMWARE M FUNCTIS DEFINED BY FIRMWARE idatastart HC

5 TACH PROGRAMMING PROCEDURE - 1 OF 1 Page 5 of vehicle for 15 seconds. ENGINE STOP 02 Press and hold the brake pedal. 03 Press and release the module s programming button. (OR if the remotes are already programmed to the vehicle, press and hold the start button of the remote for 2.5 seconds.) 04 Wait, LED 2 will flash GREEN. (See the Module Diagnostics page) 05 Release the brake pedal. 06 Module Programming Procedure completed. idatastart HC

6 REMOTE PROGRAMMING PROCEDURE - 1 OF 1 Page 6 of [4x] WARNING: Complete the module programming procedure and tach programming procedure before programming the remotes. A maximum of four [4x] remotes per system. 07 Release the antenna button. The antenna s leds will turn. 02 Set ignition to position. 08 Set ignition to position. ENGINE STOP ENGINE STOP 03 Press and release the antenna button, then press and hold the antenna button. The antenna s leds will turn solid BLUE. 09 Remote Programming Procedure completed Parking Light will flash once [1x]. Press once [1x] on the LOCK button of each remote. >> F To program an additional remote as second vehicle mode: Follow steps 1 to 4. Press twice [2x] on the F button then press once [1x] on the LOCK button of the remote. Follow steps 6 to The antenna s leds will flash BLUE once [1x] for each successful pairing. idatastart HC

7 VALET MODE PROGRAMMING PROCEDURE - 1 OF 1 Page 7 of >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 06 Valet Mode Programming Procedure completed. 01 Time restriction. Complete next step within 7 seconds. >> To exit valet mode: repeat steps 1 to Cycle ignition twice [2x /] rapidly. ENGINE STOP 03 Press and release the BRAKE pedal three times [3x]. 04 Parking Light will flash once [1x] then will flash twice [2x]. 05 Set ignition to position. ENGINE STOP idatastart HC

8 COMPATIBLE ESSORIES - 1 OF 2 Page 8 of WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE WEBLINK MOBILE (accessory sold separately) OBDII CNECTOR MODULE WEBLINK PORT 4 PIN BLACK CABLE MOBILE DEVICE PORT OBDII CNECTOR TELEMATIC KIT (accessory sold separately) MODULE TELEMATIC BLUE PORT (NC) *For SmartStart, use the module s RED Telematic port. idatastart HC

9 COMPATIBLE ESSORIES - 2 OF 2 Page 9 of RF DECODER (included with the HCF) RF KIT (sold separately) MODULE RF PORT RF DECODER - FT-D100 (NC) RED (NC) BLACK BLACK BLUE or WHITE RF KIT FLASH THE DECODER BEFORE THE INSTALLATI BLUE CABLE DECODER BLACK CABLE ANTENNA RF KIT (included with the HC1 & HC2) MODULE RF PORT 4 PIN BLACK CABLE ANTENNA idatastart HC

10 online MoDULe SeTTINgS - 1 OF 1 Page 10 of WeB PRogRaMMaBLe MeNUS MENU 1 Remote Starter MENU 2 Doorlock Options MENU 3 Security Options MENU 4 AUX function assignments MENU 5 Programmable outputs (POC) MENU 6 Pulse Timer Output Configuration (PTO) MENU 7 Input Configurations MENU 8 Output Configurations Programming options are avaible through Weblink and Weblink Mobile only. DeSCRIPTIoN RS related configuration options Convenience feature configuration options Alarm activation and settings Set transmitter AUX buttons controls Set actions for programmable outputs Set duration for pulse timer outputs (if used) Set inputs for Auto by firmware/data/analog Set outputs for Auto by firmware/data/analog idatastart HC

11 MoDULe DIagNoSTICS - 1 OF 1 Page 11 of TeST MoDULe LeD 1 STaTUS DIagNoSTIC I II III IV DURING MODULE PROGRAMMING DURING TACH PROGRAMMING DURING REMOTE WITH IGNITI Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. 1 GREEN flash Tach signal programmed in Analog 2 GREEN flashes Tach signal programmed in Data 3 RED flashes No tach signal detected 4 RED flashes System is in valet mode 5 RED flashes Tach set for VTS. No tach programming required 6 RED flashes Tach set for assumed start. No tach programming required Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. idatastart HC

12 ReMoTe STaRTeR error CoDeS - 1 OF 1 Page 12 of ReMoTe STaRTeR error CoDeS: NoTeS [X] NUMBeR of PaRKINg LIgHT flashes DIagNoSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash three [3x] times, then will flash [X] number times to indicate an error code. See table. 01 Engine running. 02 Key in ignition at position. 03 Door is open. 04 Trunk is open. 05 Foot brake is. 06 Hood is open. 07 The reservation is. (Manual transmission only) 08 Tach failure. 09 The vehicle is moving (VSS). 10 System is in Valet Mode. 11 CAN communication failure 12 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence. 13 Bypass problem. ReMoTe STaRTeR SHUTDoWN error CoDeS: NoTeS [Y] NUMBeR of PaRKINg LIgHT flashes DIagNoSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for 2.5 seconds when using a 1-WAY remote. OR Press once [1x] on button 4 when using a 2-WAY remote. The parking lights will flash four [4x] times, then will flash [Y] number times to indicate an error code. See table. 01 Engine tach signal is lost. 02 Emergency brake is lost. 03 Foot brake is. 04 Hood is open. 05 Engine RPM limiter is. 06 Glow plug timeout error. 07 Vehicle is moving (VSS). 08 N/A 09 N/A 10 Door is open. 11 CAN communication failure during RS sequence. 12 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence. 13 Takeover is not allowed. 14 Shutdown error, board overheat protection. idatastart HC

13 MODULE RESET PROCEDURE - 1 OF 1 Page 13 of >> The following procedure resets the module programming to the vehicle. It does not reset any settings configured online. 06 Module RESET completed. 01 Disconnect all connectors from module except the M1 BLACK 8-pin connector and the M4 BLACK 20-pin connector. 07 Reconnect all connectors. 02 Disconnect the M1 BLACK 8-pin connector and the M4 BLACK 20-pin connector. 08 Repeat programming procedure. 03 PRESS AND HOLD the module s programming button while connecting the M1 BLACK 8-pin connector and the M4 BLACK 20-pin connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 04 Wait, LED 1 will flash RED. RELEASE programming button. 05 LED 1 will turn RED for 2 seconds. idatastart HC

14 INSTALL GUIDE Hyundai Accent STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RST)-HK2-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIAL) DRE MOBILE DR-2000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

15 HARDWIRE / COMPENT LOCATOR - 1 OF 1 PAGE 2 OF 7 B D A C 01A_V1_[W]

16 HARDWIRE / WIRING DIAGRAM - 1 OF 1 PAGE 3 OF 7 M1! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSI LY ER (+) WHITE - 01 ESSORY (+) ORANGE V (+) GREEN : WHITE IGNITI SWITCH (A) M1 01 ORANGE - ESSORY (+) 02 RED - 12V (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE 07 RED - 12V (+) 08 BLACK - GROUND IGNITI (+) PINK - 06 TACH (AC) GREEN : WHITE 42 PIN 2: GRAY I/P JUNCTI BOX (B) M2 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT - ARM (-) OUTPUT 05 GREEN/BLACK BLACK DOT - DISARM (-) OUTPUT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT 12 WHITE BLACK DOT- PARKING LIGHT (-) OUTPUT BRAKE (+) GREEN - 02 IMMOBILIZER (DATA) BLUE/BLACK : BLACK M3 M4 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 10 EMPTY 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED - IMMO. (DATA) VEHICLE SIDE 12 GRAY/YELLOW 13 GREEN/RED - IMMO. (DATA) CNECTOR SIDE 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK LOCK (-) BLUE - 06 UNLOCK (-) YELLOW/BLACK - 16 DISARM (-) WHITE/BLACK - 33 ARM (-) YELLOW/ORANGE - 35 PARKING LIGHT (-) RED : WHITE 16 PIN 1: BLUE 42 PIN 1: BLUE DRIVER KICK PANEL (C) HEADLAMP SWITCH (D) 9 M5 01 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT - IMMO. (DATA) CNECTOR SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - IMMO. (DATA) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 1 01A_V1_[W] INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E. 1

17 MODULE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 4 OF 7 01 Insert key into ignition. 07 Press and hold the brake pedal. 02 Turn key to position. 08 Press and release the module s programming button. 03 Wait, LED 1 will flash RED and GREEN. This may take up to 3 minutes. 09 Release the brake pedal. 04 Wait, LED 1 will turn solid GREEN for 2 seconds. 10 Wait, LED 2 will flash GREEN. 05 Turn key to position. 11 Module Programming Procedure completed. 06 vehicle for 15 seconds.

18 TAKEOVER PROCEDURE - STD KEY - 1 OF 1 PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed.

19 INSTALLATI CHECKLIST - 1 OF 2 PAGE 6 OF 7 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. Question 1: Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 10 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed.

20 INSTALLATI CHECKLIST - 2 OF 2 PAGE 7 OF 7 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 14 Exit vehicle. 15 Installation checklist completed.

21 INSTALL GUIDE Hyundai Accent STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RST)-HK2-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIAL) DRE MOBILE DR-2000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

22 HARDWIRE / COMPENT LOCATOR - 1 OF 1 PAGE 2 OF 7 B C A E D F 02A_v1_[W]

23 HARDWIRE / WIRING DIAGRAM - 1 OF 1 PAGE 3 OF 7 M1! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSI LY 12V (+) GREEN - 01 ESSORY (+) ORANGE - 02 ER (+) WHITE : WHITE IGNITI SWITCH (A) M1 01 ORANGE - ESSORY (+) 02 RED - 12V (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE 07 RED - 12V (+) 08 BLACK - GROUND IGNITI (+) PINK - 04 IMMOBILIZER (DATA) BLUE/ORANGE : BLACK I/P JUNCTI BOX (B) 1 M2 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT - DISARM (-) OUTPUT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT - AUTOLIGHT (-) OUTPUT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT 12 WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT PARKING LIGHT (-) PINK/BLACK - 07 OR ORANGE : WHITE 14 PIN 2: WHITE 13 PIN 1: WHITE I/P JUNCTI BOX (C) DRIVER KICK PANEL (D) M3 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 10 EMPTY DRIVER DOOR PIN (-) BROWN/ORANGE LOCK (-) BROWN UNLOCK (-) GRAY DISARM KEY UNLOCK (-) GRAY/ORANGE - 12 UNLOCK DETECTI (-) BLUE/BLACK M4 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW BRAKE (+) PINK/BLACK BLUE/RED 06 BLUE/YELLOW 07 EMPTY TACH (AC) GREEN ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED - IMMO. (DATA) VEHICLE SIDE 12 GRAY/YELLOW 13 GREEN/RED - IMMO. (DATA) CNECTOR SIDE 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK 1 1: BLACK 3 PIN BRAKE SWITCH (E) CAMSHAFT POSITI SENSOR (F) M5 01 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT - IMMO. (DATA) CNECTOR SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - IMMO. (DATA) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT 02A_v1_[W] HORN (-) HOOD SWITCH 3 WITH AUTOLIGHT LY. 1 WITH BCM LY. VEHICLES WITHOUT BCM ADD ACTUATOR IN DRIVER DOOR. 2 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E. 3

24 MODULE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 4 OF 7 01 Insert key into ignition. 07 Press and hold the brake pedal. 02 Turn key to position. 08 Press and release the module s programming button. 03 Wait, LED 1 will flash RED and GREEN. This may take up to 3 minutes. 09 Release the brake pedal. 04 Wait, LED 1 will turn solid GREEN for 2 seconds. 10 Wait, LED 2 will flash GREEN. 05 Turn key to position. 11 Module Programming Procedure completed. 06 vehicle for 15 seconds.

25 TAKEOVER PROCEDURE - STD KEY - 1 OF 1 PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed.

26 INSTALLATI CHECKLIST - 1 OF 2 PAGE 6 OF 7 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. Question 1: Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 10 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed.

27 INSTALLATI CHECKLIST - 2 OF 2 PAGE 7 OF 7 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 14 Exit vehicle. 15 Installation checklist completed.

28 INSTALL GUIDE Hyundai Elantra STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RST)-HK2-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIAL) DRE MOBILE DR-2000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

29 HARDWIRE / COMPENT LOCATOR - 1 OF 1 PAGE 2 OF 7 C A D B E D 14A_V1_[W]

30 HARDWIRE / WIRING DIAGRAM - 1 OF 1 PAGE 3 OF 7 M1! M2 M3 M1 M2 M3 M5 M4 01 ORANGE - ESSORY (+) 02 RED - 12V (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE 07 RED - 12V (+) 08 BLACK - GROUND! CUT LOOP FOR AUTOMATIC TRANSMISSI LY 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT - AUTOLIGHT (-) OUTPUT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT 12 WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 10 EMPTY ER (+) WHITE - 01 ESSORY (+) ORANGE OR PINK V (+) BLACK OR ORANGE - 05 IGNITI (+) BLUE - 06 TRUNK RELEASE (-) WHITE - 05 UNLOCK DETECTI (-) BLACK/ORANGE - 02 DISARM KEY UNLOCK (-) YELLOW/GREEN OR YELLOW- 06 UNLOCK (-) YELLOW - 39 ARM (-) GREEN - 23 LOCK (-) GREEN - 25 DRIVER DOOR PIN (-) RED PARKING LIGHT (-) ORANGE OR BLUE - 08 BRAKE (+) WHITE - 01 TACH (AC) BLUE/RED - 05 IMMOBILIZER (DATA) BLUE/BLACK : WHITE : GRAY 39 PIN 1: WHITE 14 PIN 1 1: GRAY IGNITI SWITCH (A) DRIVER KICK PANEL (B) PARKING LIGHT SWITCH (C) BRAKE SWITCH (D) PASSENGER KICK PANEL (E) 1 M4 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED - IMMO. (DATA) CNECTOR SIDE 12 GRAY/YELLOW 13 GREEN/RED - IMMO. (DATA) VEHICLE SIDE 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK HORN (-) HOOD SWITCH 2 M5 01 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT - IMMO. (DATA) CNECTOR SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - IMMO. (DATA) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT WITH AUTOLIGHT LY. 1 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E. 2 14A_V1_[W] WIRE MAY BE FOUND THE BACKSIDE OF CNECTOR. 3

31 MODULE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 4 OF 7 01 Insert key into ignition. 07 Press and hold the brake pedal. 02 Turn key to position. 08 Press and release the module s programming button. 03 Wait, LED 1 will flash RED and GREEN. This may take up to 3 minutes. 09 Release the brake pedal. 04 Wait, LED 1 will turn solid GREEN for 2 seconds. 10 Wait, LED 2 will flash GREEN. 05 Turn key to position. 11 Module Programming Procedure completed. 06 vehicle for 15 seconds.

32 TAKEOVER PROCEDURE - STD KEY - 1 OF 1 PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed.

33 INSTALLATI CHECKLIST - 1 OF 2 PAGE 6 OF 7 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. Question 1: Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 10 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed.

34 INSTALLATI CHECKLIST - 2 OF 2 PAGE 7 OF 7 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 14 Exit vehicle. 15 Installation checklist completed.

35 INSTALL GUIDE Hyundai Elantra Touring STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RST)-HK2-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIAL) DRE MOBILE DR-2000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

36 HARDWIRE / COMPENT LOCATOR - 1 OF 1 PAGE 2 OF 7 C A D B E D 14A_V1_[W]

37 HARDWIRE / WIRING DIAGRAM - 1 OF 1 PAGE 3 OF 7 M1! M2 M3 M1 M2 M3 M5 M4 01 ORANGE - ESSORY (+) 02 RED - 12V (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE 07 RED - 12V (+) 08 BLACK - GROUND! CUT LOOP FOR AUTOMATIC TRANSMISSI LY 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT - AUTOLIGHT (-) OUTPUT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT 12 WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 10 EMPTY ER (+) WHITE - 01 ESSORY (+) ORANGE OR PINK V (+) BLACK OR ORANGE - 05 IGNITI (+) BLUE - 06 TRUNK RELEASE (-) WHITE - 05 UNLOCK DETECTI (-) BLACK/ORANGE - 02 DISARM KEY UNLOCK (-) YELLOW/GREEN OR YELLOW- 06 UNLOCK (-) YELLOW - 39 ARM (-) GREEN - 23 LOCK (-) GREEN - 25 DRIVER DOOR PIN (-) RED PARKING LIGHT (-) ORANGE OR BLUE - 08 BRAKE (+) WHITE - 01 TACH (AC) BLUE/RED - 05 IMMOBILIZER (DATA) BLUE/BLACK : WHITE : GRAY 39 PIN 1: WHITE 14 PIN 1 1: GRAY IGNITI SWITCH (A) DRIVER KICK PANEL (B) PARKING LIGHT SWITCH (C) BRAKE SWITCH (D) PASSENGER KICK PANEL (E) 1 M4 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED - IMMO. (DATA) CNECTOR SIDE 12 GRAY/YELLOW 13 GREEN/RED - IMMO. (DATA) VEHICLE SIDE 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK HORN (-) HOOD SWITCH 2 M5 01 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT - IMMO. (DATA) CNECTOR SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - IMMO. (DATA) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT WITH AUTOLIGHT LY. 1 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E. 2 14A_V1_[W] WIRE MAY BE FOUND THE BACKSIDE OF CNECTOR. 3

38 MODULE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 4 OF 7 01 Insert key into ignition. 07 Press and hold the brake pedal. 02 Turn key to position. 08 Press and release the module s programming button. 03 Wait, LED 1 will flash RED and GREEN. This may take up to 3 minutes. 09 Release the brake pedal. 04 Wait, LED 1 will turn solid GREEN for 2 seconds. 10 Wait, LED 2 will flash GREEN. 05 Turn key to position. 11 Module Programming Procedure completed. 06 vehicle for 15 seconds.

39 TAKEOVER PROCEDURE - STD KEY - 1 OF 1 PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed.

40 INSTALLATI CHECKLIST - 1 OF 2 PAGE 6 OF 7 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. Question 1: Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 10 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed.

41 INSTALLATI CHECKLIST - 2 OF 2 PAGE 7 OF 7 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 14 Exit vehicle. 15 Installation checklist completed.

42 INSTALL GUIDE Hyundai Santa Fe STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RST)-HK2-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIAL) DRE MOBILE DR-2000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

43 HARDWIRE / COMPENT LOCATOR - 1 OF 1 PAGE 2 OF 7 C A B E D 12A_V1_[W]

44 HARDWIRE / WIRING DIAGRAM - 1 OF 1 PAGE 3 OF 7 M1! M2 M3 M1 M2 M5 M4 01 ORANGE - ESSORY (+) 02 RED - 12V (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE 07 RED - 12V (+) 08 BLACK - GROUND! CUT LOOP FOR AUTOMATIC TRANSMISSI LY 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT - AUTOLIGHT (-) OUTPUT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT 12 WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT ER (+) GREEN - 01 ESSORY (+) RED OR BLUE V (+) RED - 05 IGNITI (+) ORANGE - 06 ARM (-) BROWN/ORANGE - 05 LOCK (-) BLUE/BLACK - 18 UNLOCK DETECTI (-) GRAY - 04 DISARM KEY UNLOCK (-) PINK - 06 UNLOCK (-) GRAY/BLACK - 19 DRIVER DOOR PIN (-) GREEN/ORANGE 1 BRAKE (+) GREEN/ORANGE - 21 PARKING LIGHT (-) BLUE/ORANGE : BLACK 1: BROWN : HARNESS IN RUNNING BOARD 3: BLUE 22 PIN 1: WHITE IGNITI SWITCH (A) DRIVER KICK PANEL (B) PARKING LIGHT SWITCH (C) M3 M4 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 10 EMPTY 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED - IMMO. (DATA) CNECTOR SIDE 12 GRAY/YELLOW 13 GREEN/RED - IMMO. (DATA) VEHICLE SIDE 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK TACH (AC) IMMOBILIZER (DATA) : RED OR WHITE : WHITE/ORANGE, WHITE OR RED HORN (-) 2 HOOD SWITCH 3 1: BLUE INJECTOR (D) PASSENGER KICK PANEL (E) 1 M5 01 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT - IMMO. (DATA) CNECTOR SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - IMMO. (DATA) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT WITH AUTOLIGHT LY. 1 12A_V1_[W] INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E. 3

45 MODULE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 4 OF 7 01 Insert key into ignition. 07 Press and hold the brake pedal. 02 Turn key to position. 08 Press and release the module s programming button. 03 Wait, LED 1 will flash RED and GREEN. This may take up to 3 minutes. 09 Release the brake pedal. 04 Wait, LED 1 will turn solid GREEN for 2 seconds. 10 Wait, LED 2 will flash GREEN. 05 Turn key to position. 11 Module Programming Procedure completed. 06 vehicle for 15 seconds.

46 TAKEOVER PROCEDURE - STD KEY - 1 OF 1 PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed.

47 INSTALLATI CHECKLIST - 1 OF 2 PAGE 6 OF 7 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. Question 1: Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 10 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed.

48 INSTALLATI CHECKLIST - 2 OF 2 PAGE 7 OF 7 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 14 Exit vehicle. 15 Installation checklist completed.

49 INSTALL GUIDE Hyundai Sonata STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RST)-HK2-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIAL) DRE MOBILE DR-2000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

50 HARDWIRE / COMPENT LOCATOR - 1 OF 1 PAGE 2 OF 7 C B A E D 15A_v1_[W]

51 HARDWIRE / WIRING DIAGRAM - 1 OF 1 PAGE 3 OF 7 M1! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSI LY ER (+) GREEN V (+) RED - 02 ESSORY (+) ORANGE : WHITE IGNITI SWITCH (A) M1 M2 M3 01 ORANGE - ESSORY (+) 02 RED - 12V (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE 07 RED - 12V (+) 08 BLACK - GROUND 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT - AUTOLIGHT (-) OUTPUT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT 12 WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 10 EMPTY IGNITI (+) BLUE - 06 PARKING LIGHT (-) PINK - 14 DRIVER DOOR PIN (-) WHITE IMMOBILIZER (DATA) GREEN - 23 LOCK (-) YELLOW - 06 TRUNK RELEASE (-) WHITE - 16 UNLOCK DETECTI (-) BROWN : WHITE BROWN 18 PIN GRAY 24 PIN HEADLAMP SWITCH (B) DASH FUSEVOX, REAR (C) DRIVER KICK PANEL (D) 1 M4 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED - IMMO. (DATA) CNECTOR SIDE 12 GRAY/YELLOW 13 GREEN/RED - IMMO. (DATA) VEHICLE SIDE 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK TACH (AC) WHITE - 28 BRAKE (+) GREEN - 01 BLACK 33 PIN BRAKE SWITCH (E) M5 01 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT - IMMO. (DATA) CNECTOR SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - IMMO. (DATA) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 2 WITH AUTOLIGHT LY. 1 15A_v1_[W] INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E. 2

52 MODULE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 4 OF 7 01 Insert key into ignition. 07 Press and hold the brake pedal. 02 Turn key to position. 08 Press and release the module s programming button. 03 Wait, LED 1 will flash RED and GREEN. This may take up to 3 minutes. 09 Release the brake pedal. 04 Wait, LED 1 will turn solid GREEN for 2 seconds. 10 Wait, LED 2 will flash GREEN. 05 Turn key to position. 11 Module Programming Procedure completed. 06 vehicle for 15 seconds.

53 TAKEOVER PROCEDURE - STD KEY - 1 OF 1 PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed.

54 INSTALLATI CHECKLIST - 1 OF 2 PAGE 6 OF 7 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. Question 1: Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 10 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed.

55 INSTALLATI CHECKLIST - 2 OF 2 PAGE 7 OF 7 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 14 Exit vehicle. 15 Installation checklist completed.

56 INSTALL GUIDE Hyundai Sonata STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RST)-HK2-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIAL) DRE MOBILE DR-2000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

57 HARDWIRE / COMPENT LOCATOR - 1 OF 1 PAGE 2 OF 7 C B A E D 15A_v2_[W]

58 HARDWIRE / WIRING DIAGRAM - 1 OF 1 PAGE 3 OF 7 M1! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSI LY ER (+) GREEN V (+) RED - 02 ESSORY (+) ORANGE : WHITE IGNITI SWITCH (A) M1 M2 M3 01 ORANGE - ESSORY (+) 02 RED - 12V (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE 07 RED - 12V (+) 08 BLACK - GROUND 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT - AUTOLIGHT (-) OUTPUT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT 12 WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 10 EMPTY IGNITI (+) BLUE - 06 PARKING LIGHT (-) PINK - 14 DRIVER DOOR PIN (-) WHITE IMMOBILIZER (DATA) GREEN - 23 LOCK (-) YELLOW - 06 TRUNK RELEASE (-) WHITE - 16 UNLOCK DETECTI (-) BROWN : WHITE BROWN 18 PIN GRAY 24 PIN HEADLAMP SWITCH (B) DASH FUSEVOX, REAR (C) DRIVER KICK PANEL (D) 1 M4 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED - IMMO. (DATA) CNECTOR SIDE 12 GRAY/YELLOW 13 GREEN/RED - IMMO. (DATA) VEHICLE SIDE 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK UNLOCK (-) ORANGE - 03 TACH (AC) WHITE - 28 BRAKE (+) GREEN - 01 BLACK 33 PIN BRAKE SWITCH (E) M5 01 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT - IMMO. (DATA) CNECTOR SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - IMMO. (DATA) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 2 WITH AUTOLIGHT LY. 1 15A_v2_[W] INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E. 2

59 MODULE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 4 OF 7 01 Insert key into ignition. 07 Press and hold the brake pedal. 02 Turn key to position. 08 Press and release the module s programming button. 03 Wait, LED 1 will flash RED and GREEN. This may take up to 3 minutes. 09 Release the brake pedal. 04 Wait, LED 1 will turn solid GREEN for 2 seconds. 10 Wait, LED 2 will flash GREEN. 05 Turn key to position. 11 Module Programming Procedure completed. 06 vehicle for 15 seconds.

60 TAKEOVER PROCEDURE - STD KEY - 1 OF 1 PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed.

61 INSTALLATI CHECKLIST - 1 OF 2 PAGE 6 OF 7 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. Question 1: Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 10 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed.

62 INSTALLATI CHECKLIST - 2 OF 2 PAGE 7 OF 7 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 14 Exit vehicle. 15 Installation checklist completed.

63 INSTALL GUIDE Hyundai Tiburon 4 cyl STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RST)-HK2-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIAL) DRE MOBILE DR-2000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

64 HARDWIRE / COMPENT LOCATOR - 1 OF 1 PAGE 2 OF 7 F E A C B D 03A_v1_[W]

65 HARDWIRE / WIRING DIAGRAM - 1 OF 1 PAGE 3 OF 7 M1! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSI LY ER (+) WHITE - 01 ESSORY (+) PINK V (+) RED : WHITE IGNITI SWITCH (A) M1 01 ORANGE - ESSORY (+) 02 RED - 12V (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE - TRUNK RELEASE (+) 07 RED - 12V (+) 08 BLACK - GROUND IGNITI (+) RED - 06 TRUNK (+) BLUE 1 DISARM (-) ORANGE DRIVER DOOR PIN (-) GRAY/BLACK 2 1: HARNESS IN RUNNING BOARD DRIVER KICK PANEL (B) M2 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT - DISARM (-) OUTPUT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT - AUTOLIGHT (-) OUTPUT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT 12 WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT BRAKE (+) WHITE - 01 TACH (AC) GREEN OR BLACK/RED PARKING LIGHTS (-) BLUE/ORANGE : WHITE 18 PIN 1 BCM-EF: WHITE (BOTTOM RIGHT) BRAKE SWITCH (C) IGNITI COIL (D) HEADLAMP SWITCH (E) BCM/DASH FUSEBOX (F) FRT VIEW M3 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 10 EMPTY A LOCK/UNLOCK (-) YELLOW - 08 IMMOBILIZER (DATA) BLUE/ORANGE : WHITE REAR VIEW M4 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED - IMMO. (DATA) VEHICLE SIDE 12 GRAY/YELLOW 13 GREEN/RED - IMMO. (DATA) CNECTOR SIDE 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK M5 01 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT - IMMO. (DATA) CNECTOR SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - IMMO. (DATA) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT 03A_v1_[W] HORN (-) HOOD SWITCH 3 MUST SET PROGRAMMABLE HIGH POWER RELAY #5 IN MENU 1 TO TRUNK RELEASE. 1 WITH AUTOLIGHT LY. 2 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E. 3

66 MODULE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 4 OF 7 01 Insert key into ignition. 07 Press and hold the brake pedal. 02 Turn key to position. 08 Press and release the module s programming button. 03 Wait, LED 1 will flash RED and GREEN. This may take up to 3 minutes. 09 Release the brake pedal. 04 Wait, LED 1 will turn solid GREEN for 2 seconds. 10 Wait, LED 2 will flash GREEN. 05 Turn key to position. 11 Module Programming Procedure completed. 06 vehicle for 15 seconds.

67 TAKEOVER PROCEDURE - STD KEY - 1 OF 1 PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed.

68 INSTALLATI CHECKLIST - 1 OF 2 PAGE 6 OF 7 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. Question 1: Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 10 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed.

69 INSTALLATI CHECKLIST - 2 OF 2 PAGE 7 OF 7 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 14 Exit vehicle. 15 Installation checklist completed.

70 INSTALL GUIDE Hyundai Tucson 2.0L STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RST)-HK2-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIAL) DRE MOBILE DR-2000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

71 HARDWIRE / COMPENT LOCATOR - 1 OF 1 PAGE 2 OF 7 B A D C 04A_v1_[W]

72 HARDWIRE / WIRING DIAGRAM - 1 OF 1 PAGE 3 OF 7 M1! M2 M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSI LY ER (+) PINK - 01 ESSORY (+) PINK V (+) RED OR ORANGE : WHITE IGNITI SWITCH (A) M1 01 ORANGE - ESSORY (+) 02 RED - 12V (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE 07 RED - 12V (+) 08 BLACK - GROUND IGNITI (+) ORANGE - 06 PARKING LIGHTS (-) BLUE/BLACK OR BLUE IMMOBILIZER (DATA) BLUE/BLACK OR BROWN/ORANGE : BLUE/BLACK HEADLAMP SWITCH (B) PASSENGER KICK PANEL (C) M2 M3 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT - ARM (-) OUTPUT 05 GREEN/BLACK BLACK DOT - DISARM (-) OUTPUT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT - AUTOLIGHT (-) OUTPUT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT 12 WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 10 EMPTY TACH (AC) BLUE - 09 DRIVER DOOR PIN (-) RED BRAKE (+) WHITE - 15 LOCK (-) WHITE/BLACK OR GRAY - 19 UNLOCK (-) YELLOW/ORANGE OR GREEN - 20 ARM (-) YELLOW DISARM (-) BROWN : 20 PIN DRIVER KICK PANEL (D) M4 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED - IMMO. (DATA) VEHICLE SIDE 12 GRAY/YELLOW 13 GREEN/RED - IMMO. (DATA) CNECTOR SIDE 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK HORN (-) HOOD SWITCH 3 M5 01 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT - IMMO. (DATA) CNECTOR SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - IMMO. (DATA) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT WITH AUTOLIGHT LY. 1 WITH OEM ALARM LY. 2 04A_v1_[W] INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E. 3

73 MODULE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 4 OF 7 01 Insert key into ignition. 07 Press and hold the brake pedal. 02 Turn key to position. 08 Press and release the module s programming button. 03 Wait, LED 1 will flash RED and GREEN. This may take up to 3 minutes. 09 Release the brake pedal. 04 Wait, LED 1 will turn solid GREEN for 2 seconds. 10 Wait, LED 2 will flash GREEN. 05 Turn key to position. 11 Module Programming Procedure completed. 06 vehicle for 15 seconds.

74 TAKEOVER PROCEDURE - STD KEY - 1 OF 1 PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed.

75 INSTALLATI CHECKLIST - 1 OF 2 PAGE 6 OF 7 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. Question 1: Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 10 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed.

76 INSTALLATI CHECKLIST - 2 OF 2 PAGE 7 OF 7 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 14 Exit vehicle. 15 Installation checklist completed.

77 INSTALL GUIDE Kia Forte STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RST)-HK2-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIAL) DRE MOBILE DR-2000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

78 HARDWIRE / COMPENT LOCATOR - 1 OF 1 PAGE 2 OF 7 D C A B E D 13A_V1_[W]

79 HARDWIRE / WIRING DIAGRAM - 1 OF 1 PAGE 3 OF 7 M1! M2 M3 M1 M2 M3 M5 M4 01 ORANGE - ESSORY (+) 02 RED - 12V (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE 07 RED - 12V (+) 08 BLACK - GROUND! CUT LOOP FOR AUTOMATIC TRANSMISSI LY 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT - AUTOLIGHT (-) OUTPUT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT 12 WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 10 EMPTY ER (+) WHITE - 01 ESSORY (+) ORANGE V (+) BLACK - 05 IGNITI (+) BLUE - 06 UNLOCK DETECTI (-) BLACK/ORANGE - 02 DISARM KEY UNLOCK (-) BLUE/ORANGE - 06 UNLOCK (-) YELLOW - 39 ARM (-) GREEN/ORANGE - 23 LOCK (-) GREEN - 25 BRAKE (+) WHITE - 20 DRIVER DOOR PIN (-) RED PARKING LIGHT (-) ORANGE - 01 TRUNK RELEASE (-) BLUE/BLACK - 02 TACH (AC) BLUE/RED - 05 IMMOBILIZER (DATA) LTBLUE/BLACK OR YELLOW/ORANGE : BLACK : GRAY 39 PIN 1: WHITE 13 PIN 1: WHITE 18 PIN CNECTOR 1: GRAY IGNITI SWITCH (A) DRIVER KICK PANEL (B) PARKING LIGHT SWITCH (C) DASH FUSE BOX, REAR VIEW (D) PASSENGER KICK PANEL (E) 1 M4 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED - IMMO. (DATA) CNECTOR SIDE 12 GRAY/YELLOW 13 GREEN/RED - IMMO. (DATA) VEHICLE SIDE 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK HORN (-) HOOD SWITCH 2 M5 01 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT - IMMO. (DATA) CNECTOR SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - IMMO. (DATA) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT WITH AUTOLIGHT LY. 1 13A_V1_[W] INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E. 2

80 MODULE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 4 OF 7 01 Insert key into ignition. 07 Press and hold the brake pedal. 02 Turn key to position. 08 Press and release the module s programming button. 03 Wait, LED 1 will flash RED and GREEN. This may take up to 3 minutes. 09 Release the brake pedal. 04 Wait, LED 1 will turn solid GREEN for 2 seconds. 10 Wait, LED 2 will flash GREEN. 05 Turn key to position. 11 Module Programming Procedure completed. 06 vehicle for 15 seconds.

81 TAKEOVER PROCEDURE - STD KEY - 1 OF 1 PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed.

82 INSTALLATI CHECKLIST - 1 OF 2 PAGE 6 OF 7 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. Question 1: Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 10 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed.

83 INSTALLATI CHECKLIST - 2 OF 2 PAGE 7 OF 7 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 14 Exit vehicle. 15 Installation checklist completed.

84 INSTALL GUIDE Kia Magentis STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RST)-HK2-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIAL) DRE MOBILE DR-2000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

85 HARDWIRE / COMPENT LOCATOR - 1 OF 1 PAGE 2 OF 7 B A C 06A_v1_[W]

86 HARDWIRE / WIRING DIAGRAM - 1 OF 1 PAGE 3 OF 7 M1! M2 M3 M1 M2 M5 M4 01 ORANGE - ESSORY (+) 02 RED - 12V (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - 12V (+) 08 BLACK - GROUND! CUT LOOP FOR AUTOMATIC TRANSMISSI LY 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK RELEASE (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT - AUTOLIGHT (-) OUTPUT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT 12 WHITE BLACK DOT ER (+) GREEN - 01 ESSORY (+) BLACK V (+) PINK - 05 IGNITI (+) GREEN - 06 PARKING LIGHTS (+) RED - 06 DRIVER DOOR PIN (-) ORANGE/BLACK : BLACK 1: WHITE : BROWN 1: WHITE IGNITI SWITCH (A) DASH FUSEBOX, REAR VIEW (B) DRIVER KICK PANEL (C) M3 M4 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 10 EMPTY 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED - IMMO. (DATA) CNECTOR SIDE 12 GRAY/YELLOW 13 GREEN/RED - IMMO. (DATA) VEHICLE SIDE 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK IMMOBILIZER (DATA) YELLOW/ORANGE - 21 BRAKE (+) RED - 01 TRUNK RELEASE (-) WHITE/BLACK - 06 TACH (AC) YELLOW/BLACK - 05 LOCK/ARM (-) GREEN - 12 UNLOCK/DISARM (-) ORANGE - 17 HORN (-) HOOD SWITCH : BLACK : WHITE 33 PIN 4: BLUE 20 PIN 5: BROWN 20 PIN 4 1 M5 01 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT - IMMO. (DATA) CNECTOR SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - IMMO. (DATA) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT WITH AUTOLIGHT LY. 1 06A_v1_[W] INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E. 2

87 MODULE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 4 OF 7 01 Insert key into ignition. 07 Press and hold the brake pedal. 02 Turn key to position. 08 Press and release the module s programming button. 03 Wait, LED 1 will flash RED and GREEN. This may take up to 3 minutes. 09 Release the brake pedal. 04 Wait, LED 1 will turn solid GREEN for 2 seconds. 10 Wait, LED 2 will flash GREEN. 05 Turn key to position. 11 Module Programming Procedure completed. 06 vehicle for 15 seconds.

88 TAKEOVER PROCEDURE - STD KEY - 1 OF 1 PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed.

89 INSTALLATI CHECKLIST - 1 OF 2 PAGE 6 OF 7 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. Question 1: Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 10 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed.

90 INSTALLATI CHECKLIST - 2 OF 2 PAGE 7 OF 7 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 14 Exit vehicle. 15 Installation checklist completed.

91 INSTALL GUIDE Kia Magentis STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RST)-HK2-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIAL) DRE MOBILE DR-2000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

92 HARDWIRE / COMPENT LOCATOR - 1 OF 1 PAGE 2 OF 7 B A C 06A_v2_[W]

93 HARDWIRE / WIRING DIAGRAM - 1 OF 1 PAGE 3 OF 7 M1! M2 M3 M1 M2 M5 M4 01 ORANGE - ESSORY (+) 02 RED - 12V (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - 12V (+) 08 BLACK - GROUND! CUT LOOP FOR AUTOMATIC TRANSMISSI LY 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK RELEASE (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT - AUTOLIGHT (-) OUTPUT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT 12 WHITE BLACK DOT ER (+) GREEN - 01 ESSORY (+) BLACK V (+) PINK - 05 IGNITI (+) GREEN - 06 PARKING LIGHTS (+) RED - 06 DRIVER DOOR PIN (-) ORANGE/BLACK : BLACK 1: WHITE : BROWN 1: WHITE IGNITI SWITCH (A) DASH FUSEBOX, REAR VIEW (B) DRIVER KICK PANEL (C) M3 M4 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 10 EMPTY 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED - IMMO. (DATA) CNECTOR SIDE 12 GRAY/YELLOW 13 GREEN/RED - IMMO. (DATA) VEHICLE SIDE 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK IMMOBILIZER (DATA) YELLOW/ORANGE - 21 BRAKE (+) RED - 01 TRUNK RELEASE (-) WHITE/BLACK - 06 TACH (AC) YELLOW/BLACK - 05 LOCK/ARM (-) GREEN - 12 UNLOCK DETECTI (-) BROWN/ORANGE - 16 UNLOCK/DISARM (-) ORANGE - 17 HORN (-) HOOD SWITCH : BLACK : WHITE 33 PIN 4: BLUE 20 PIN 5: BROWN 20 PIN 4 1 M5 01 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT - IMMO. (DATA) CNECTOR SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - IMMO. (DATA) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT WITH AUTOLIGHT LY. 1 06A_v2_[W] INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E. 2

94 MODULE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 4 OF 7 01 Insert key into ignition. 07 Press and hold the brake pedal. 02 Turn key to position. 08 Press and release the module s programming button. 03 Wait, LED 1 will flash RED and GREEN. This may take up to 3 minutes. 09 Release the brake pedal. 04 Wait, LED 1 will turn solid GREEN for 2 seconds. 10 Wait, LED 2 will flash GREEN. 05 Turn key to position. 11 Module Programming Procedure completed. 06 vehicle for 15 seconds.

95 TAKEOVER PROCEDURE - STD KEY - 1 OF 1 PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed.

96 INSTALLATI CHECKLIST - 1 OF 2 PAGE 6 OF 7 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. Question 1: Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 10 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed.

97 INSTALLATI CHECKLIST - 2 OF 2 PAGE 7 OF 7 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 14 Exit vehicle. 15 Installation checklist completed.

98 INSTALL GUIDE Kia Optima STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RST)-HK2-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIAL) DRE MOBILE DR-2000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

99 HARDWIRE / COMPENT LOCATOR - 1 OF 1 PAGE 2 OF 7 B A C 06A_v1_[W]

100 HARDWIRE / WIRING DIAGRAM - 1 OF 1 PAGE 3 OF 7 M1! M2 M3 M1 M2 M5 M4 01 ORANGE - ESSORY (+) 02 RED - 12V (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - 12V (+) 08 BLACK - GROUND! CUT LOOP FOR AUTOMATIC TRANSMISSI LY 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK RELEASE (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT - AUTOLIGHT (-) OUTPUT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT 12 WHITE BLACK DOT ER (+) GREEN - 01 ESSORY (+) BLACK V (+) PINK - 05 IGNITI (+) GREEN - 06 PARKING LIGHTS (+) RED - 06 DRIVER DOOR PIN (-) ORANGE/BLACK : BLACK 1: WHITE : BROWN 1: WHITE IGNITI SWITCH (A) DASH FUSEBOX, REAR VIEW (B) DRIVER KICK PANEL (C) M3 M4 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 10 EMPTY 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED - IMMO. (DATA) CNECTOR SIDE 12 GRAY/YELLOW 13 GREEN/RED - IMMO. (DATA) VEHICLE SIDE 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK IMMOBILIZER (DATA) YELLOW/ORANGE - 21 BRAKE (+) RED - 01 TRUNK RELEASE (-) WHITE/BLACK - 06 TACH (AC) YELLOW/BLACK - 05 LOCK/ARM (-) GREEN - 12 UNLOCK/DISARM (-) ORANGE - 17 HORN (-) HOOD SWITCH : BLACK : WHITE 33 PIN 4: BLUE 20 PIN 5: BROWN 20 PIN 4 1 M5 01 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT - IMMO. (DATA) CNECTOR SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - IMMO. (DATA) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT WITH AUTOLIGHT LY. 1 06A_v1_[W] INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E. 2

101 MODULE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 4 OF 7 01 Insert key into ignition. 07 Press and hold the brake pedal. 02 Turn key to position. 08 Press and release the module s programming button. 03 Wait, LED 1 will flash RED and GREEN. This may take up to 3 minutes. 09 Release the brake pedal. 04 Wait, LED 1 will turn solid GREEN for 2 seconds. 10 Wait, LED 2 will flash GREEN. 05 Turn key to position. 11 Module Programming Procedure completed. 06 vehicle for 15 seconds.

102 TAKEOVER PROCEDURE - STD KEY - 1 OF 1 PAGE 5 OF 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed.

103 INSTALLATI CHECKLIST - 1 OF 2 PAGE 6 OF 7 CHECKLIST - WITH AFTERMARKET KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. Question 1: Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 10 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed.

104 INSTALLATI CHECKLIST - 2 OF 2 PAGE 7 OF 7 CHECKLIST - WITH OEM KEYFOB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 14 Exit vehicle. 15 Installation checklist completed.

105 INSTALL GUIDE Kia Optima STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RST)-HK2-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIAL) DRE MOBILE DR-2000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

idatastart HC Document number Revision Date

idatastart HC Document number Revision Date PRODUCT guide idatastart HC Document number Revision Date 0503 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that

More information

idatastart HC Document number Revision Date

idatastart HC Document number Revision Date PRODUCT guide idatastart HC Document number Revision Date 05 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that

More information

PRODUCT GUIDE HCF900A DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE HCF900A DOCUMENT NUMBER REVISION DATE PRODUCT GUIDE DOCUMENT NUMBER REVISION DATE 20161024 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either

More information

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE 206025 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that

More information

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE PRODUCT GUIDE FT-DC-S DOCUMENT NUMBER REVISION DATE 060809 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that

More information

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE PRODUCT GUIDE FT-DC-S DOCUMENT NUMBER REVISION DATE 0605 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either

More information

idatastart HC Document number Revision Date

idatastart HC Document number Revision Date PRODUCT guide Document number Revision Date 20151001 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either

More information

PRODUCT GUIDE HC1151A DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE HC1151A DOCUMENT NUMBER REVISION DATE PRODUCT GUIDE HC5A DOCUMENT NUMBER REVISION DATE 0604 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either

More information

PRODUCT GUIDE VWX000A DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE VWX000A DOCUMENT NUMBER REVISION DATE PRODUCT GUIDE DOCUMENT NUMBER REVISION DATE 20161107 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either

More information

PRODUCT GUIDE OL-RS-VW1 DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE OL-RS-VW1 DOCUMENT NUMBER REVISION DATE PRODUCT GUIDE DOCUMENT NUMBER REVISION DATE 20180116 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either

More information

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE PRODUCT GUIDE DOCUMENT NUMBER REVISION DATE 20161025 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either

More information

PRODUCT GUIDE ORBIT1151A DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE ORBIT1151A DOCUMENT NUMBER REVISION DATE PRODUCT GUIDE ORBIT5A DOCUMENT NUMBER REVISION DATE 2060728 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that

More information

install guide ADS-AL(RS)-FM6-[ADS-ALCA]-EN

install guide ADS-AL(RS)-FM6-[ADS-ALCA]-EN install guide Document number 07 Revision Date 050 firmware ADS-AL(RS)-FM6-[ADS-ALCA] hardware ADS-ALCA accessories ADS-USB (REQUIRED) COMPATIBLE RF-KIT (REQUIRED) NOTICE The manufacturer will accept no

More information

PRODUCT GUIDE CMVWXA0

PRODUCT GUIDE CMVWXA0 PRODUCT GUIDE DOCUMENT NUMBER REVISION DATE 20181116 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either

More information

INSTALL GUIDE OEM-AL(RS)-CH8-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-CH8-[FLCAN]-EN INSTALL GUIDE DOCUMENT NUMBER 5644 REVISI DATE 084 FIRMWARE OEM-AL(RS)-CH8-[FLCAN] HARDWARE FLCAN ESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly intended

More information

INSTALL GUIDE OEM-AL(RS)-FM6-[OL-MDB-ALL]-EN

INSTALL GUIDE OEM-AL(RS)-FM6-[OL-MDB-ALL]-EN INSTALL GUIDE DOCUMENT NUMBER 507 REVISION DATE 05 FIRMWARE OEM-AL(RS)-FM6-[OL-MDB-ALL] HARDWARE OL-MDB-ALL ESSORIES OL-LOADER (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical

More information

INSTALL GUIDE OEM-AL(RS)-FM8-[ADS-ALCA]-EN

INSTALL GUIDE OEM-AL(RS)-FM8-[ADS-ALCA]-EN INSTALL GUIDE DOCUMENT NUMBER 979 REVISION DATE 070 FIRMWARE OEM-AL(RS)-FM8-[ADS-ALCA] HARDWARE ADS-ALCA ESSORIES ADS-USB (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical

More information

Alarms & Remote Start

Alarms & Remote Start Alarms & Remote Start INSTALL GUIDE DOCUMENT NUMBER 809 REVISION DATE 0608 FIRMWARE COL-AL(RS)-VW6-[OL-MDB-ALL] HARDWARE OL-MDB-ALL ACCESSORIES OL-LOADER (REQUIRED) OMEGA-CARLINK-GPS (OPTIONAL) NOTICE

More information

Alarms & Remote Start

Alarms & Remote Start Alarms & Remote Start INSTALL GUIDE DOCUMENT NUMBER 80 REVISION DATE 008 FIRMWARE OEM-AL(RS)-VW-[OL-MDB-ALL] HARDWARE OL-MDB-ALL ACCESSORIES OL-LOADER (REQUIRED) NOTICE The manufacturer will accept no

More information

INSTALL GUIDE OEM-AL(RS)-NI9-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-NI9-[FLCAN]-EN INSTALL GUIDE DOCUMENT NUMBER 5506 REVISION DATE 08098 FIRMWARE OEM-AL(RS)-NI9-[FLCAN] HARDWARE FLCAN ACCESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly

More information

INSTALL GUIDE OEM-AL(RS)-NI8-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-NI8-[FLCAN]-EN INSTALL GUIDE DOCUMENT NUMBER 5679 REVISION DATE 084 FIRMWARE OEM-AL(RS)-NI8-[FLCAN] HARDWARE FLCAN ACCESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly

More information

Alarms & Remote Start

Alarms & Remote Start Alarms & Remote Start INSTALL GUIDE OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN DOCUMENT NUMBER 990 REVISION DATE 008 FIRMWARE OEM-AL(RS)-CH0-[OL-MDB-ALL] HARDWARE OL-MDB-ALL ACCESSORIES OL-LOADER (REQUIRED) NOTICE

More information

PRODUCT GUIDE RS1B-DC2 DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE RS1B-DC2 DOCUMENT NUMBER REVISION DATE PRODUCT GUIDE RSB-DC2 DOCUMENT NUMBER REVISION DATE 25 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either

More information

INSTALL GUIDE OEM-AL(RS)-CH5-[ADS-ALCA]-EN

INSTALL GUIDE OEM-AL(RS)-CH5-[ADS-ALCA]-EN INSTALL GUIDE OEM-AL(RS)-CH-[ADS-ALCA]-EN DOCUMENT NUMBER 8 REVISI DATE 00 FIRMWARE OEM-AL(RS)-CH-[ADS-ALCA] HARDWARE ADS-ALCA ACCESSORIES ADS-USB (REQUIRED) ADS-HRN-CH (REQUIRED) NOTICE The manufacturer

More information

INSTALL GUIDE OEM-AL(RS)-CH8-[OL-MDB-ALL]-EN

INSTALL GUIDE OEM-AL(RS)-CH8-[OL-MDB-ALL]-EN INSTALL GUIDE DOCUMENT NUMBER 90 REVISI DATE 0809 IRMWARE OEM-AL(RS)-CH8-[OL-MDB-ALL] HARDWARE OL-MDB-ALL ESSORIES OL-LOADER (REQUIRED) TERMS O USE: Automotive Data Solutions Inc. ( ADS ) products are

More information

INSTALL GUIDE ORB-AL(RS)-CH4-[ADS-ALCA]-EN

INSTALL GUIDE ORB-AL(RS)-CH4-[ADS-ALCA]-EN INSTALL GUIDE DOCUMENT NUMBER 8457 REVISI DATE 7 FIRMWARE ORB-AL(RS)-CH4-[ADS-ALCA] HARDWARE ADS-ALCA ESSORIES ADS-USB (REQUIRED) ADS-HRN-CH4 (REQUIRED) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer

More information

INSTALL GUIDE OEM-AL(RS)-FM6-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-FM6-[FLCAN]-EN INSTALL GUIDE DOCUMENT NUMBER 53668 REVISION DATE 208098 FIRMWARE OEM-AL(RS)-FM6-[FLCAN] HARDWARE FLCAN ACCESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly

More information

INSTALL GUIDE OEM-AL(RS)-TL1-[ADS-ALCA]-EN

INSTALL GUIDE OEM-AL(RS)-TL1-[ADS-ALCA]-EN INSTALL GUIDE DOCUMENT NUMBER 56703 REVISION DATE 084 FIRMWARE OEM-AL(RS)-TL-[ADS-ALCA] HARDWARE ADS-ALCA ACCESSORIES ADS-USB (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are

More information

INSTALL GUIDE OEM-AL(RS)-TL2-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-TL2-[FLCAN]-EN INSTALL GUIDE OEM-AL(RS)-TL-[FLCAN]-EN DOCUMENT NUMBER 5364 REVISION DATE 08098 FIRMWARE OEM-AL(RS)-TL-[FLCAN] HARDWARE FLCAN ACCESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc.

More information

INSTALL GUIDE ORB-AL(RS)-CH5-[ADS-ALCA]-EN

INSTALL GUIDE ORB-AL(RS)-CH5-[ADS-ALCA]-EN INSTALL GUIDE DOCUMENT NUMBER 97 REVISION DATE 08078 FIRMWARE ORB-AL(RS)-CH-[ADS-ALCA] HARDWARE ADS-ALCA ACCESSORIES ADS-USB (REQUIRED) ADS-HRN-CH (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) TERMS OF USE:

More information

INSTALL GUIDE OL-AL(RS)-CH5-[OL-MDB-ALL]-EN

INSTALL GUIDE OL-AL(RS)-CH5-[OL-MDB-ALL]-EN INSTALL GUIDE OL-AL(RS)-CH-[OL-MDB-ALL]-EN DOCUMENT NUMBER 8 REVISION DATE 009 FIRMWARE OL-AL(RS)-CH-[OL-MDB-ALL] HARDWARE OL-MDB-ALL ACCESSORIES OL-LOADER (REQUIRED) OL-HRN-CH (REQUIRED) RF-0/0/0-EDP

More information

INSTALL GUIDE OEM-AL(RS)-FM8-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-FM8-[FLCAN]-EN INSTALL GUIDE DOCUMENT NUMBER 53938 REVISION DATE 208098 FIRMWARE OEM-AL(RS)-FM8-[FLCAN] HARDWARE FLCAN ACCESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly

More information

INSTALL GUIDE OEM-AL(RS)-TL7-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-TL7-[FLCAN]-EN INSTALL GUIDE DOCUMENT NUMBER 545 REVISION DATE 08098 FIRMWARE OEM-AL(RS)-TL7-[FLCAN] HARDWARE FLCAN ACCESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly

More information

INSTALL GUIDE OEM-AL(RS)-CH5-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-CH5-[FLCAN]-EN INSTALL GUIDE OEM-AL(RS)-CH-[FLCAN]-EN DOCUMENT NUMBER 8 REVISION DATE 00 FIRMWARE OEM-AL(RS)-CH-[FLCAN] HARDWARE FLCAN ACCESSORIES FLPROG (REQUIRED) FLCHH (REQUIRED) NOTICE The manufacturer will accept

More information

INSTALL GUIDE OEM-AL(RS)-CH5-[ADS-ALCA]-EN

INSTALL GUIDE OEM-AL(RS)-CH5-[ADS-ALCA]-EN INSTALL GUIDE DOCUMENT NUMBER 53964 REVISION DATE 28098 FIRMWARE OEM-AL(RS)-CH5-[ADS-ALCA] HARDWARE ADS-ALCA ACCESSORIES ADS-USB (REQUIRED) ADS-HRN-CH5 (REQUIRED) TERMS OF USE: Automotive Data Solutions

More information

install guide OEM-AL(RS)-FM6-[ADS-ALCA]-EN

install guide OEM-AL(RS)-FM6-[ADS-ALCA]-EN install guide Document number 5 Revision Date 08 firmware OEM-AL(RS)-FM6-[ADS-ALCA] hardware ADS-ALCA accessories ADS-USB (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical

More information

install guide FLC-CH(RS)-CH4-[FLRSCH4]-EN

install guide FLC-CH(RS)-CH4-[FLRSCH4]-EN install guide Document number 655 Revision Date 098 firmware FLC-CH(RS)-CH4-[FLRSCH4] hardware FLRSCH4 accessories FLPROG (REQUIRED) FLRF//4 (OPTIAL) CARLINK ASCL (OPTIAL) NOTICE The manufacturer will

More information

INSTALL GUIDE IDL-HA(RS)-HA7-[ADS-HA7]-EN

INSTALL GUIDE IDL-HA(RS)-HA7-[ADS-HA7]-EN INSTALL GUIDE DOCUMENT NUMBER 090 REVISION DATE 7070 FIRMWARE IDL-HA(RS)-HA7-[ADS-HA7] HARDWARE ADS-HA7 ACCESSORIES ADS-USB (REQUIRED) COMPATIBLE RF-KIT (REQUIRED) DIRECTED SMARTSTART & ADS-HRN(RS)-SM

More information

INSTALL GUIDE FLC-CH(RS)-CH8-[FLRSCH7]-EN

INSTALL GUIDE FLC-CH(RS)-CH8-[FLRSCH7]-EN INSTALL GUIDE DOCUMENT NUMBER REVISION DATE 080 FIRMWARE FLC-CH(RS)-CH8-[FLRSCH7] HARDWARE FLRSCH7 ESSORIES FLPROG (REQUIRED) FLRF// (OPTIONAL) CARLINK ASCL (OPTIONAL) TERMS OF USE: Automotive Data Solutions

More information

INSTALL GUIDE OL-FO(RS)-FO1B-[OL-RS-FO1]-EN

INSTALL GUIDE OL-FO(RS)-FO1B-[OL-RS-FO1]-EN INSTALL GUIDE DOCUMENT NUMBER 54456 REVISION DATE 01818 FIRMWARE OL-FO(RS)-FO1B-[OL-RS-FO1] HARDWARE OL-RS-FO1 ACCESSORIES OL-LOADER (REQUIRED) RF-/30/50-EDP (OPTIONAL) LINKR (OPTIONAL) TERMS OF USE: Automotive

More information

INSTALL GUIDE DIR-CH(RS)-CH8-[FLRSCH10]-EN

INSTALL GUIDE DIR-CH(RS)-CH8-[FLRSCH10]-EN INSTALL GUIDE DOCUMENT NUMBER 870 REVISION DATE 080 FIRMWARE DIR-CH(RS)-CH8-[FLRSCH0] HARDWARE FLRSCH0 ESSORIES FLPROG (REQUIRED) DIRECTED XL-0 RF-KIT & ADS-HRN(RS)-XL0 (OPTIONAL) DIRECTED SMART & ADS-HRN(RS)-SM0

More information

INSTALL GUIDE COM-HA(RS)-HA6P-[FT-HA6-DC]-EN

INSTALL GUIDE COM-HA(RS)-HA6P-[FT-HA6-DC]-EN INSTALL GUIDE DOCUMENT NUMBER 49378 REVISION DATE 20180412 FIRMWARE COM-HA(RS)-HA6P-[FT-HA6-DC] HARDWARE FT-HA6-DC ACCESSORIES ADS-USB (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL)

More information

INSTALL GUIDE OL-HA(RS)-HA6P-[OL-RS-HA6]-EN

INSTALL GUIDE OL-HA(RS)-HA6P-[OL-RS-HA6]-EN INSTALL GUIDE DOCUMENT NUMBER 5699 REVISION DATE 7 FIRMWARE OL-HA(RS)-HA6P-[OL-RS-HA6] HARDWARE OL-RS-HA6 ACCESSORIES OL-LOADER (REQUIRED) RF-0/0/50-EDP (OPTIONAL) LINKR (OPTIONAL) NOTICE The manufacturer

More information

INSTALL GUIDE FLC-HA(RS)-HA6P-[FLRSHA6]-EN

INSTALL GUIDE FLC-HA(RS)-HA6P-[FLRSHA6]-EN INSTALL GUIDE DOCUMENT NUMBER 49388 REVISION DATE 20180412 FIRMWARE FLC-HA(RS)-HA6P-[FLRSHA6] HARDWARE FLRSHA6 ACCESSORIES FLPROG (REQUIRED) FLRF1/2/4 (OPTIONAL) CARLINK ASCL2 (OPTIONAL) TERMS OF USE:

More information

INSTALL GUIDE OEM-CH(RS)-CH4-[ADS-CH4]-EN

INSTALL GUIDE OEM-CH(RS)-CH4-[ADS-CH4]-EN INSTALL GUIDE DOCUMENT NUMBER 864 REVISI DATE 77 FIRMWARE OEM-CH(RS)-CH4-[ADS-CH4] HARDWARE ADS-CH4 ACCESSORIES ADS-USB (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical

More information

INSTALL GUIDE FLCI-CH(RS)-CH7-[FLRSCH7]-EN

INSTALL GUIDE FLCI-CH(RS)-CH7-[FLRSCH7]-EN INSTALL GUIDE DOCUMENT NUMBER 57668 REVISION DATE FIRMWARE FLCI-CH(RS)-CH7-[FLRSCH7] HARDWARE FLRSCH7 ACCESSORIES FLPROG (REQUIRED) FLRF//4 (OPTIONAL) MYCAR (OPTIONAL) TERMS OF USE: Automotive Data Solutions

More information

INSTALL GUIDE ORB-AL(RS)-CH4-[ADS-ALCA]-EN

INSTALL GUIDE ORB-AL(RS)-CH4-[ADS-ALCA]-EN INSTALL GUIDE DOCUMENT NUMBER 54929 REVISION DATE 2810 FIRMWARE ORB-AL(RS)-CH4-[ADS-ALCA] HARDWARE ADS-ALCA ACCESSORIES ADS-USB (REQUIRED) ADS-HRN-CH4 (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) TERMS OF USE:

More information

INSTALL GUIDE COM-CH(RS)-CH4-[FT-CH4-DC]-EN

INSTALL GUIDE COM-CH(RS)-CH4-[FT-CH4-DC]-EN INSTALL GUIDE DOCUMENT NUMBER 49560 REVISION DATE 20180411 FIRMWARE COM-CH(RS)-CH4-[FT-CH4-DC] HARDWARE FT-CH4-DC ACCESSORIES ADS-USB (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL)

More information

INSTALL GUIDE FLC-NI(RS)-NI6-[FLRSNI5]-EN

INSTALL GUIDE FLC-NI(RS)-NI6-[FLRSNI5]-EN INSTALL GUIDE FLC-NI(RS)-NI-[FLRSNI]-EN DOCUMENT NUMBER REVISION DE 000 FIRMWARE FLC-NI(RS)-NI-[FLRSNI] HARDWARE FLRSNI ACCESSORIES FLPROG (REQUIRED) FLRF// (OPTIONAL) CARLINK ASCL (OPTIONAL) NOTICE The

More information

INSTALL GUIDE OEM-GM(RS)-GM2-[OL-RS-GM2]-EN

INSTALL GUIDE OEM-GM(RS)-GM2-[OL-RS-GM2]-EN INSTALL GUIDE OEM-GM(RS)-GM-[OL-RS-GM]-EN DOCUMENT NUMBER 0 REVISION DATE 0 FIRMWARE OEM-GM(RS)-GM-[OL-RS-GM] HARDWARE OL-RS-GM ACCESSORIES OL-LOADER (REQUIRED) NOTICE The manufacturer will accept no responsability

More information

INSTALL GUIDE AKX-IDS(RS)-BZ1B-[ADS-BZ1]-EN

INSTALL GUIDE AKX-IDS(RS)-BZ1B-[ADS-BZ1]-EN INSTALL GUIDE DOCUMENT NUMBER 25893 REVISION DATE 2627 FIRMWARE AKX-IDS(RS)-BZ1B-[ADS-BZ1] HARDWARE ADS-BZ1 ESSORIES ADS-USB (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) DIRECTED SMART & ADS-HRN(RS)-SM (OPTIONAL)

More information

INSTALL GUIDE OEM-CH(RS)-CH8-[FLRSCH10]-EN

INSTALL GUIDE OEM-CH(RS)-CH8-[FLRSCH10]-EN INSTALL GUIDE DOCUMENT NUMBER 58012 REVISION DATE 20190114 FIRMWARE OEM-CH(RS)-CH8-[FLRSCH10] HARDWARE FLRSCH10 ESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products

More information

INSTALL GUIDE COM-CH(RS)-CH5-[FT-CH5-DC]-EN

INSTALL GUIDE COM-CH(RS)-CH5-[FT-CH5-DC]-EN INSTALL GUIDE DOCUMENT NUMBER 89 REVISION DATE 707 FIRMWARE COM-CH(RS)-CH-[FT-CH-DC] HARDWARE FT-CH-DC ACCESSORIES ADS-USB (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) NOTICE

More information

INSTALL GUIDE OEM-GM(RS)-GM2-[ADS-GM2]-EN

INSTALL GUIDE OEM-GM(RS)-GM2-[ADS-GM2]-EN INSTALL GUIDE DOCUMENT NUMBER 0 REVISION DATE FIRMWARE OEM-GM(RS)-GM-[ADS-GM] HARDWARE ADS-GM ACCESSORIES ADS-USB (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical damage

More information

INSTALL GUIDE OL-CH(RS)-CH4-[OL-RS-CH4]-EN

INSTALL GUIDE OL-CH(RS)-CH4-[OL-RS-CH4]-EN INSTALL GUIDE DOCUMENT NUMBER 49581 REVISION DATE 20180411 FIRMWARE OL-CH(RS)-CH4-[OL-RS-CH4] HARDWARE OL-RS-CH4 ACCESSORIES OL-LOADER (REQUIRED) RF-10/30/50-EDP (OPTIONAL) LINKR (OPTIONAL) TERMS OF USE:

More information

INSTALL GUIDE IDL-IDS(RS)-BZ2B-[ADS-BZ2]-EN

INSTALL GUIDE IDL-IDS(RS)-BZ2B-[ADS-BZ2]-EN INSTALL GUIDE DOCUMENT NUMBER 450 REVISION DATE FIRMWARE IDL-IDS(RS)-BZB-[ADS-BZ] HARDWARE ADS-BZ ESSORIES ADS-USB (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) DIRECTED SMART & ADS-HRN(RS)-SM0 (OPTIONAL) ADS-TOOLS-MB0

More information

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: January 18, 2018 Doc. No.: ##47334##

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: January 18, 2018 Doc. No.: ##47334## Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-HK7-EN AVAILABLE FOR : ADS-AL CA Rev. Date: January 8, 08 Doc. No.: ##7## HK7 U.S. PATENT NO. 8,8,780 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE

More information

install guide FLC-CH(RS)-CH5-[FLRSCH5]-EN

install guide FLC-CH(RS)-CH5-[FLRSCH5]-EN install guide Document number 89 Revision Date 00 firmware FLC-CH(RS)-CH-[FLRSCH] hardware FLRSCH accessories FLPROG (REQUIRED) FLRF// (OPTIONAL) CARLINK ASCL (OPTIONAL) NOTICE The manufacturer will accept

More information

Automotive Data Solutions Inc. AVAILABLE FOR : FLCAN. Rev. Date: June 28, 2018 Doc. No.: ##51678##

Automotive Data Solutions Inc. AVAILABLE FOR : FLCAN. Rev. Date: June 28, 2018 Doc. No.: ##51678## Automotive Data Solutions Inc. INSTALL GUIDE FLC-AL(DL)-HK-EN AVAILABLE FOR : FLCAN Rev. Date: June, 0 Doc. No.: #### HK U.S. PATENT NO.,,0 PLEASE VISIT WWW.FLASHLOGIC.COM FOR COMPLETE PRODUCT DETAILS

More information

INSTALL GUIDE FLCI-IDS(RS)-BZ4-[FLRSBZ4]-EN

INSTALL GUIDE FLCI-IDS(RS)-BZ4-[FLRSBZ4]-EN INSTALL GUIDE DOCUMENT NUMBER 58247 REVISION DATE 20190116 FIRMWARE FLCI-IDS(RS)-BZ4-[FLRSBZ4] HARDWARE FLRSBZ4 ACCESSORIES FLPROG (REQUIRED) FLRF1/2/4 (OPTIONAL) MYCAR (OPTIONAL) TERMS OF USE: Automotive

More information

INSTALL GUIDE FLC-GM(RS)-GM10-[FLRSGM10]-EN

INSTALL GUIDE FLC-GM(RS)-GM10-[FLRSGM10]-EN INSTALL GUIDE DOCUMENT NUMBER 9 REVISION DATE FIRMWARE FLC-GM(RS)-GM0-[FLRSGM0] HARDWARE FLRSGM0 ACCESSORIES FLPROG (REQUIRED) FLRF// (OPTIONAL) CARLINK ASCL (OPTIONAL) NOTICE The manufacturer will accept

More information

INSTALL GUIDE COM-CH(RS)-CH5-[FT-CH5-DC]-EN

INSTALL GUIDE COM-CH(RS)-CH5-[FT-CH5-DC]-EN INSTALL GUIDE DOCUMENT NUMBER 54983 REVISION DATE 01810 FIRMWARE COM-CH(RS)-CH5-[FT-CH5-DC] HARDWARE FT-CH5-DC ACCESSORIES ADS-USB (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL)

More information

install guide COM-IDS(RS)-BM1-[ADS-BM1]-EN

install guide COM-IDS(RS)-BM1-[ADS-BM1]-EN install guide Document number Revision Date 50 firmware COM-IDS(RS)-BM-[ADS-BM] hardware ADS-BM accessories ADS-USB (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) NOTICE The manufacturer

More information

INSTALL GUIDE OL-NI(RS)-NI5-[OL-RS-NI5]-EN

INSTALL GUIDE OL-NI(RS)-NI5-[OL-RS-NI5]-EN INSTALL GUIDE DOCUMENT NUMBER 54560 REVISION DE 201818 FIRMWARE OL-NI(RS)-NI5-[OL-RS-NI5] HARDWARE OL-RS-NI5 ACCESSORIES OL-LOADER (REQUIRED) RF-10/30/50-EDP (OPTIONAL) LINKR (OPTIONAL) TERMS OF USE: Automotive

More information

install guide OEM-IDS(RS)-BM1-[ADS-BM1]-EN

install guide OEM-IDS(RS)-BM1-[ADS-BM1]-EN install guide Document number 13171 Revision Date 231121 firmware OEM-IDS(RS)-BM1-[ADS-BM1] hardware ADS-BM1 accessories ADS-USB (REQUIRED) NOTICE The manufacturer will accept no responsability for any

More information

INSTALL GUIDE DIR-IDS(RS)-BM1-[FLRSBM1]-EN

INSTALL GUIDE DIR-IDS(RS)-BM1-[FLRSBM1]-EN INSTALL GUIDE DOCUMENT NUMBER 57 REVISION DATE 7 FIRMWARE DIR-IDS(RS)-BM-[FLRSBM] HARDWARE FLRSBM ACCESSORIES FLPROG (REQUIRED) DIRECTED XL- RF-KIT & ADS-HRN(RS)-XL (OPTIONAL) DIRECTED SMARTSTART & ADS-HRN(RS)-SM

More information

INSTALL GUIDE IDL-IDS(RS)-BM1-[ADS-BM1]-EN

INSTALL GUIDE IDL-IDS(RS)-BM1-[ADS-BM1]-EN INSTALL GUIDE DOCUMENT NUMBER 577 REVISION DATE 7 FIRMWARE IDL-IDS(RS)-BM-[ADS-BM] HARDWARE ADS-BM ACCESSORIES ADS-USB (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) DIRECTED SMARTSTART & ADS-HRN(RS)-SM (OPTIONAL)

More information

INSTALL GUIDE AKX-IDS(RS)-BM1-[ADS-BM1]-EN

INSTALL GUIDE AKX-IDS(RS)-BM1-[ADS-BM1]-EN INSTALL GUIDE DOCUMENT NUMBER 9 REVISION DATE 7 FIRMWARE AKX-IDS(RS)-BM-[ADS-BM] HARDWARE ADS-BM ACCESSORIES ADS-USB (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) DIRECTED SMARTSTART & ADS-HRN(RS)-SM (OPTIONAL)

More information

INSTALL GUIDE FLC-GM(RS)-GM10-[FLRSGM10]-EN

INSTALL GUIDE FLC-GM(RS)-GM10-[FLRSGM10]-EN INSTALL GUIDE DOCUMENT NUMBER 498 REVISION DATE 0804 FIRMWARE FLC-GM(RS)-GM0-[FLRSGM0] HARDWARE FLRSGM0 ACCESSORIES FLPROG (REQUIRED) FLRF//4 (OPTIONAL) CARLINK ASCL (OPTIONAL) TERMS OF USE: Automotive

More information

INSTALL GUIDE OEM-GM(RS)-GM10-[OL-RS-GM10]-EN

INSTALL GUIDE OEM-GM(RS)-GM10-[OL-RS-GM10]-EN INSTALL GUIDE OEM-GM(RS)-GM0-[OL-RS-GM0]-EN DOCUMENT NUMBER 555 REVISION DATE 05 FIRMWARE OEM-GM(RS)-GM0-[OL-RS-GM0] HARDWARE OL-RS-GM0 ACCESSORIES OL-LOADER (REQUIRED) NOTICE The manufacturer will accept

More information

INSTALL GUIDE FLCI-CH(RS)-CH5-[FLRSCH5]-EN

INSTALL GUIDE FLCI-CH(RS)-CH5-[FLRSCH5]-EN INSTALL GUIDE DOCUMENT NUMBER 59643 REVISION DATE 019 FIRMWARE FLCI-CH(RS)-CH5-[FLRSCH5] HARDWARE FLRSCH5 ACCESSORIES FLPROG (REQUIRED) FLRF1//4 (OPTIONAL) MYCAR (OPTIONAL) TERMS OF USE: Automotive Data

More information

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: January 18, 2018 Doc. No.: ##47342##

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: January 18, 2018 Doc. No.: ##47342## Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-NI9-EN AVAILABLE FOR : ADS-AL CA Rev. Date: January 8, 08 Doc. No.: ##4734## NI9 U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE

More information

INSTALL GUIDE OL-GM(RS)-GM10-[OL-RS-GM10]-EN

INSTALL GUIDE OL-GM(RS)-GM10-[OL-RS-GM10]-EN INSTALL GUIDE DOCUMENT NUMBER 54253 REVISION DATE 20180918 FIRMWARE OL-GM(RS)-GM10-[OL-RS-GM10] HARDWARE OL-RS-GM10 ACCESSORIES OL-LOADER (REQUIRED) RF-10/30/50-EDP (OPTIONAL) LINKR (OPTIONAL) TERMS OF

More information

Alarms & Remote Start

Alarms & Remote Start Alarms & Remote Start INSTALL GUIDE DOCUMENT NUMBER 5866 REVISION DATE 0607 FIRMWARE OEM-IDS(RS)-BM-[OL-RS-BM] HARDWARE OL-RS-BM ACCESSORIES OL-LOADER (REQUIRED) NOTICE The manufacturer will accept no

More information

install guide OEM-IDS(RS)-BM1-[ADS-BM1]-EN

install guide OEM-IDS(RS)-BM1-[ADS-BM1]-EN install guide Document number 9 Revision Date 50 firmware OEM-IDS(RS)-BM-[ADS-BM] hardware ADS-BM accessories ADS-USB (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical

More information

INSTALL GUIDE FLC-CH(RS)-CH5-[FLRSCH5]-EN

INSTALL GUIDE FLC-CH(RS)-CH5-[FLRSCH5]-EN INSTALL GUIDE DOCUMENT NUMBER 95 REVISION DATE 080 FIRMWARE FLC-CH(RS)-CH5-[FLRSCH5] HARDWARE FLRSCH5 ACCESSORIES FLPROG (REQUIRED) FLRF// (OPTIONAL) CARLINK ASCL (OPTIONAL) TERMS OF USE: Automotive Data

More information

install guide DIR-CH(RS)-CH5-[AKX-CH5]-EN

install guide DIR-CH(RS)-CH5-[AKX-CH5]-EN install guide Document number 096 Revision Date firmware DIR-CH(RS)-CH-[AKX-CH] hardware AKX-CH/AKX-CH-BAM/AKX-CH-WSS accessories ADS-USB (REQUIRED) DIRECTED XL-0 RF-KIT & ADS-HRN(RS)-XL0 (OPTIAL) DIRECTED

More information

U.S. Patent No. 8,856,780 INSTALL TYPE SELECTION INSTALL TYPE

U.S. Patent No. 8,856,780 INSTALL TYPE SELECTION INSTALL TYPE Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-HA1-EN AVAILABLE FOR : ADS-AL CA Rev. Date: November 0, 201 Doc. No.: ##45584## HA1 U.S. PATENT NO. 8,856,80 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE

More information

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: August 29, 2018 Doc. No.: ##52817##

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: August 29, 2018 Doc. No.: ##52817## Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-NI8-EN AVAILABLE FOR : ADS-AL CA Rev. Date: August 29, 2018 Doc. No.: ##52817## NI8 U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR

More information

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: May 15, 2017 Doc. No.: ##39060##

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: May 15, 2017 Doc. No.: ##39060## Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-HA3-EN AVAILABLE FOR : ADS-AL CA Rev. Date: May 15, 2017 Doc. No.: ##39060## HA3 U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE

More information

install guide OEM-CH(RS)-CH5-[FLRSCH5]-EN

install guide OEM-CH(RS)-CH5-[FLRSCH5]-EN install guide Document number 8 Revision Date 008 firmware OEM-CH(RS)-CH-[FLRSCH] hardware FLRSCH accessories FLPROG (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical

More information

VW7 INSTALL GUIDE ADS-AL(DL)-VW7-EN. Alarms & Remote Start. Automotive Data Solutions Inc.

VW7 INSTALL GUIDE ADS-AL(DL)-VW7-EN. Alarms & Remote Start. Automotive Data Solutions Inc. Alarms & Remote Start Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-VW7-EN AVAILABLE FOR : ADS-AL CA Rev. Date: March 03, 06 Doc. No.: ##789## U.S. PATENT NO. 8,856,780 VW7 The brand names and

More information

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: September 14, 2017 Doc. No.: ##44374##

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: September 14, 2017 Doc. No.: ##44374## Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-NI1-EN NI1 AVAILABLE FOR : ADS-AL CA Rev. Date: September 14, 2017 Doc. No.: ##44374## U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR

More information

HA2 INSTALL GUIDE ADS-AL(DL)-HA2-EN. Alarms & Remote Start. Automotive Data Solutions Inc.

HA2 INSTALL GUIDE ADS-AL(DL)-HA2-EN. Alarms & Remote Start. Automotive Data Solutions Inc. Alarms & Remote Start Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-HA2-EN AVAILABLE FOR : ADS-AL CA Rev. Date: May 20, 2016 Doc. No.: ##28730## U.S. PATENT NO. 8,856,780 HA2 The brand names

More information

VW3 INSTALL GUIDE OL-AL(MDB)-VW3-EN. Alarms & Remote Start. Automotive Data Solutions Inc.

VW3 INSTALL GUIDE OL-AL(MDB)-VW3-EN. Alarms & Remote Start. Automotive Data Solutions Inc. Alarms & Remote Start Automotive Data Solutions Inc. VW3 OL-AL(MDB)-VW3-EN AVAILABLE FOR : OL-MDB-ALL Rev. Date: March 04, 06 Doc. No.: ##757## U.S. PATENT NO. 8,856,780 The brand names and logos found

More information

Automotive Data Solutions Inc.

Automotive Data Solutions Inc. Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-FM FM Available for : ADS-AL CA Rev. Date: March 9, 0 Doc. No.: ##885## 006 Version FRançaise disponible en ligne au www.idatalink.com please visit

More information

Automotive Data Solutions Inc. AVAILABLE FOR : FLCAN. Rev. Date: February 25, 2019 Doc. No.: ##59301##

Automotive Data Solutions Inc. AVAILABLE FOR : FLCAN. Rev. Date: February 25, 2019 Doc. No.: ##59301## Automotive Data Solutions Inc. FLC-AL(DL)-FM3-EN AVAILABLE FOR : FLCAN Rev. Date: February 5, 09 Doc. No.: ##5930## FM3 PENT NO. US 8,856,780 CA 7596 PLEASE VISIT WWW.FLASHLOGIC.COM FOR COMPLETE PRODUCT

More information

Automotive Data Solutions Inc. Rev. Date: August 17, 2015 Doc. No.: ##22710##

Automotive Data Solutions Inc. Rev. Date: August 17, 2015 Doc. No.: ##22710## Automotive Data Solutions Inc. INSTALL GUIDE DBI-AL(DL)-SUB-EN SUB Available for : DBI-AL CA Rev. Date: August 7, 205 Doc. No.: ##2270## please visit www.idatalink.com for complete product details The

More information

Automotive Data Solutions Inc. Rev. Date: November 26, 2013 Doc. No.: ##13245##

Automotive Data Solutions Inc. Rev. Date: November 26, 2013 Doc. No.: ##13245## Automotive Data Solutions Inc. INSTALL GUIDE DBI-AL(RS-CH-EN CH Available for : ADS-AL CA Rev. Date: November, 0 Doc. No.: #### Version FRançaise disponible en ligne au www.idatalink.com please visit for

More information

install guide OEM-GM(RS)-GM10-[FLRSGM10]-EN

install guide OEM-GM(RS)-GM10-[FLRSGM10]-EN install guide Document number 13581 Revision Date 2420 firmware OEM-GM(RS)-GM10-[FLRSGM10] hardware FLRSGM10 accessories FLPROG (REQUIRED) NOTICE The manufacturer will accept no responsability for any

More information

Automotive Data Solutions Inc. AVAILABLE FOR : FLCAN. Rev. Date: December 27, 2017 Doc. No.: ##46765##

Automotive Data Solutions Inc. AVAILABLE FOR : FLCAN. Rev. Date: December 27, 2017 Doc. No.: ##46765## Automotive Data Solutions Inc. FLC-AL(DL)-HA2-EN AVAILABLE FOR : FLCAN Rev. Date: December 27, 2017 Doc. No.: ##46765## HA2 U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.FLASHLOGIC.COM FOR COMPLETE PRODUCT

More information

VW3 INSTALL GUIDE ADS-AL(DL)-VW3-EN. Alarms & Remote Start. Automotive Data Solutions Inc.

VW3 INSTALL GUIDE ADS-AL(DL)-VW3-EN. Alarms & Remote Start. Automotive Data Solutions Inc. Alarms & Remote Start Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-VW3-EN AVAILABLE FOR : ADS-AL CA Rev. Date: March 04, 2016 Doc. No.: ##27565## U.S. PATENT NO. 8,856,780 VW3 The brand names

More information

HA2 INSTALL GUIDE OL-AL(MDB)-HA2-EN. Alarms & Remote Start. Automotive Data Solutions Inc.

HA2 INSTALL GUIDE OL-AL(MDB)-HA2-EN. Alarms & Remote Start. Automotive Data Solutions Inc. Alarms & Remote Start Automotive Data Solutions Inc. HA OL-AL(MDB)-HA-EN AVAILABLE FOR : OL-MDB-ALL Rev. Date: May 0, 06 U.S. PATENT NO. 8,86,780 The brand names and logos found in this guide are property

More information

Automotive Data Solutions Inc. Rev. Date: November 16, 2012 Doc. No.: ##10129##

Automotive Data Solutions Inc. Rev. Date: November 16, 2012 Doc. No.: ##10129## Automotive Data Solutions Inc. INSTALL GUIDE DBI-AL(DL)-GM-EN Available for : DBI-AL CA Rev. Date: November, 0 Doc. No.: ##09## 0 GM Version FRançaise disponible en ligne au www.idatalink.com please visit

More information

TL2 INSTALL GUIDE OL-AL(MDB)-TL2-EN. Alarms & Remote Start. Automotive Data Solutions Inc.

TL2 INSTALL GUIDE OL-AL(MDB)-TL2-EN. Alarms & Remote Start. Automotive Data Solutions Inc. Alarms & Remote Start Automotive Data Solutions Inc. INSTALL GUIDE OL-AL(MDB)-TL2-EN TL2 AVAILABLE FOR : OL-MDB-ALL Rev. Date: April 08, 2016 Doc. No.: ##28069## U.S. PATENT NO. 8,856,780 The brand names

More information

Automotive Data Solutions Inc. Rev. Date: October 28, 2015 Doc. No.: ##23962##

Automotive Data Solutions Inc. Rev. Date: October 28, 2015 Doc. No.: ##23962## Automotive Data Solutions Inc. INSTALL GUIDE FLC-AL(DL)-CH4-EN Available for : FLCAN Rev. Date: October 8, 05 Doc. No.: ##396## CH4 please visit www.flashlogic.com for complete product details The brand

More information

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: April 17, 2018 Doc. No.: ##49944##

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: April 17, 2018 Doc. No.: ##49944## Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-CH9-EN AVAILABLE FOR : ADS-AL CA Rev. Date: April 7, 08 Doc. No.: ##99## CH9 U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE

More information

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: January 03, 2018 Doc. No.: ##46808##

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: January 03, 2018 Doc. No.: ##46808## Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-CH4-EN AVAILABLE FOR : ADS-AL CA Rev. Date: January 03, 08 Doc. No.: ##46808## CH4 U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE

More information

Automotive Data Solutions Inc. Rev. Date: May 27, 2011 Doc. No.: ##5455##

Automotive Data Solutions Inc. Rev. Date: May 27, 2011 Doc. No.: ##5455## Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-NI NI Available for : ADS-AL CA Rev. Date: May 7, 0 Doc. No.: ##5455## 0055 Version FRançaise disponible en ligne au www.idatalink.com please visit

More information

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: June 19, 2018 Doc. No.: ##51396##

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: June 19, 2018 Doc. No.: ##51396## Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-MI3-EN AVAILABLE FOR : ADS-AL CA Rev. Date: June 9, 08 Doc. No.: ##5396## MI3 U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE

More information