idatastart HC Document number Revision Date

Transcription

1 PRODUCT guide idatastart HC Document number Revision Date 05 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

2 GETTING ED Page of 3 05 WeLcome Congratulations on the purchase of your idatastart HC solution. You are now a few simple steps away from enjoying your new remote starter unit with enhanced features. Before starting your installation, please ensure that your idatastart HC module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. table of contents Box Contents 3 Module Pinout 4 Tach Programming Procedure 5 Remote Programming Procedure 6 Valet Mode Programming Procedure 7 Compatible Accessories 9 Online Module Settings 0 Module Diagnostics Remote Starter Error Codes need HeLP? Module Reset Procedure support@idatalink.com idatalink.com/support idatastart HC

3 BOX CONTENTS - OF Page 3 of 3 05 BOX CONTENTS HC MODULE -WAY REMOTE - TR350AC HC - HC35AC M - 8 PIN BLACK AUTOMATIC TRANSMISSION CUT LOOP M - PIN BLACK M3-0 PIN WHITE TELEMATIC - 4 PIN BLUE TELEMATIC - 4 PIN RED NC - 4 PIN RED M5-6 PIN BLUE M4-0 PIN BLACK NC - 3 PIN BLACK PROGRAMMING BUTTON -WAY REMOTE - TR50A HC - HC35AC LED LED RF PORT/WEBLINK PORT - 4 PIN BLACK USB ANTENNA - AN300A ANTENNA CABLE HC - HC5AC ANTENNA LED HOOD SWITCH M5 M4 M3 M M ANTENNA BUTTON HCF - HCF900A RF PORT - 4 PIN BLACK RF DECODER - FT-D00 RF DECODER CABLE PIN BLACK RF PORT - 4 PIN BLACK HCX - HCX000A STICKERS 6 PIN WHITE OR BLUE ANTENNA RF PORT - 4 PIN WHITE idatastart HC

4 MODULE PINOUT - OF Page 4 of 3 05 HC MODULE M 0 ORANGE - ACCESSORY (+) 0 RED - POWER (30A) PURPLE - ER (+) PINK/WHITE - PROG. RELAY #4 - IGNITION (+) (DEFAULT) 05 PINK - IGNITION (+) 06 WHITE - PROG. RELAY #5 (0A) - PARKING LIGHTS (+) (DEFAULT) 07 RED - POWER (30A) 08 BLACK - GROUND M M 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT RED/WHITE BLACK DOT - TRUNK RELEASE (-) OUTPUT GREEN/WHITE BLACK DOT - ARM (-) OUTPUT 05 GREEN/BLACK BLACK DOT - DISARM (-) OUTPUT 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE BLACK DOT - POC - ND UNLOCK OTHER DOORS (-) OUTPUT 09 PURPLE/BLACK BLACK DOT - POC - RAP SHUTDOWN (-) OUTPUT 0 WHITE/BLACK BLACK DOT - POC 3 - HORN (-) OUTPUT BROWN/BLACK BLACK DOT - POC 4 - ER KILL (-) OUTPUT WHITE BLACK DOT - PARKING LIGHTS (-) OUTPUT AUTOMATIC TRANSMISSION CUT LOOP M M3 M5 M M3 0 BROWN SILVER DOT - BRAKE (+) INPUT 0 BLACK/WHITE SILVER DOT - E-BRAKE (-) INPUT PURPLE SILVER DOT - DOOR (+) INPUT GREEN SILVER DOT - DOOR (-) INPUT 05 PURPLE/WHITE SILVER DOT - TACH (-) INPUT 06 WHITE/BLUE SILVER DOT - X-TRIGGER (-) INPUT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT - TRUNK (-) INPUT 09 GRAY/BLACK SILVER DOT - GLOW PLUG (+) INPUT 0 EMPTY M FUNCTIONS DEFINED BY FIRMWARE M FUNCTIONS DEFINED BY FIRMWARE idatastart HC

5 TACH PROGRAMMING PROCEDURE - OF Page 5 of OFF ACC ON vehicle for 5 seconds. ENGINE STOP 0 Press and hold the brake pedal. Press and release the module s programming button. (OR if the remotes are already programmed to the vehicle, press and hold the start button of the remote for.5 seconds.) Wait, LED will flash GREEN. (See the Module Diagnostics page) 05 Release the brake pedal. 06 Module Programming Procedure completed. idatastart HC

6 REMOTE PROGRAMMING PROCEDURE - OF Page 6 of [4x] WARNING: Complete the module programming procedure and tach programming procedure before programming the remotes. A maximum of four [4x] remotes per system. 07 Release the antenna button. The antenna s leds will turn OFF. 0 OFF ACC ON Set ignition to ON position. 08 OFF ACC ON Set ignition to OFF position. ENGINE STOP ENGINE STOP Press and release the antenna button, then press and hold the antenna button. The antenna s leds will turn solid BLUE. 09 Remote Programming Procedure completed. 05 Parking Light will flash once [x]. Press once [x] on the LOCK button of each remote. >> F To program an additional remote as second vehicle mode: Follow steps to 4. Press twice [x] on the F button then press once [x] on the LOCK button of the remote. Follow steps 6 to The antenna s leds will flash BLUE once [x] for each successful pairing. idatastart HC

7 VALET MODE PROGRAMMING PROCEDURE - OF Page 7 of 3 05 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 06 Valet Mode Programming Procedure completed. 0 Time restriction. Complete next step within 7 seconds. >> To exit valet mode: repeat steps to 5. 0 OFF ACC ON Cycle ignition ON twice [x OFF/ON] rapidly. ENGINE STOP Press and release the BRAKE pedal three times [3x]. Parking Light will flash once [x] then will flash twice [x]. 05 OFF ACC ON Set ignition to OFF position. ENGINE STOP idatastart HC

8 COMPATIBLE ACCESSORIES - OF Page 8 of 3 05 WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE WEBLINK MOBILE (accessory sold separately) OBDII CONNECTOR MODULE WEBLINK PORT 4 PIN BLACK CABLE MOBILE DEVICE PORT OBDII CONNECTOR TELEMATIC KIT (accessory sold separately) MODULE TELEMATIC BLUE PORT (NC) *For SmartStart, use the module s RED Telematic port. idatastart HC

9 COMPATIBLE ACCESSORIES - OF Page 9 of 3 05 RF DECODER (included with the HCF) RF KIT (sold separately) MODULE RF PORT RF DECODER - FT-D00 (NC) RED (NC) BLACK BLACK BLUE or WHITE RF KIT FLASH THE DECODER BEFORE THE INSTALLATION BLUE CABLE DECODER BLACK CABLE ANTENNA RF KIT (included with the HC & HC) MODULE RF PORT 4 PIN BLACK CABLE ANTENNA idatastart HC

10 online MoDULe SeTTINgS - OF Page 0 of 3 05 WeB PRogRaMMaBLe MeNUS MENU Remote Starter MENU Doorlock Options MENU 3 Security Options MENU 4 AUX function assignments MENU 5 Programmable outputs (POC) MENU 6 Pulse Timer Output Configuration (PTO) MENU 7 Input Configurations MENU 8 Output Configurations Programming options are avaible through Weblink and Weblink Mobile only. DeSCRIPTIoN RS related configuration options Convenience feature configuration options Alarm activation and settings Set transmitter AUX buttons controls Set actions for programmable outputs Set duration for pulse timer outputs (if used) Set inputs for Auto by firmware/data/analog Set outputs for Auto by firmware/data/analog idatastart HC

11 MoDULe DIagNoSTICS - OF Page of 3 05 TeST MoDULe LeD STaTUS DIagNoSTIC I II III IV DURING MODULE PROGRAMMING DURING TACH PROGRAMMING DURING REMOTE WITH IGNITION OFF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed. OFF No activity or module already programmed. GREEN flash Tach signal programmed in Analog GREEN flashes Tach signal programmed in Data 3 RED flashes No tach signal detected 4 RED flashes System is in valet mode 5 RED flashes Tach set for VTS. No tach programming required 6 RED flashes Tach set for assumed start. No tach programming required Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then OFF Reset in progress. OFF Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then OFF Reset in progress. OFF Module at rest and ready for a remote start sequence. idatastart HC

12 ReMoTe STaRTeR error CoDeS - OF Page of 3 05 ReMoTe STaRTeR error CoDeS: NoTeS [X] NUMBeR of PaRKINg LIgHT flashes DIagNoSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash three [3x] times, then will flash [X] number times to indicate an error code. See table. 0 Engine running. 0 Key in ignition at ON position. Door is open. Trunk is open. 05 Foot brake is ON. 06 Hood is open. 07 The reservation is OFF. (Manual transmission only) 08 Tach failure. 09 The vehicle is moving (VSS). 0 System is in Valet Mode. CAN communication failure RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 3 Bypass problem. ReMoTe STaRTeR SHUTDoWN error CoDeS: NoTeS [Y] NUMBeR of PaRKINg LIgHT flashes DIagNoSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for.5 seconds when using a -WAY remote. OR Press once [x] on button 4 when using a -WAY remote. The parking lights will flash four [4x] times, then will flash [Y] number times to indicate an error code. See table. 0 Engine tach signal is lost. 0 Emergency brake is lost. Foot brake is ON. Hood is open. 05 Engine RPM limiter is ON. 06 Glow plug timeout error. 07 Vehicle is moving (VSS). 08 N/A 09 N/A 0 Door is open. CAN communication failure during RS sequence. RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 3 Takeover is not allowed. 4 Shutdown error, board overheat protection. idatastart HC

13 MODULE RESET PROCEDURE - OF Page 3 of 3 05 >> The following procedure resets the module programming to the vehicle. It does not reset any settings configured online. 06 Module RESET completed. 0 Disconnect all connectors from module except the M BLACK 8-pin connector and the M4 BLACK 0-pin connector. 07 Reconnect all connectors. 0 Disconnect the M BLACK 8-pin connector and the M4 BLACK 0-pin connector. 08 Repeat programming procedure. PRESS AND HOLD the module s programming button while connecting the M BLACK 8-pin connector and the M4 BLACK 0-pin connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. Wait, LED will flash RED. RELEASE programming button. 05 LED will turn RED for seconds. idatastart HC

14 INSTALL GUIDE Acura EL.7 STD key AT DOCUMENT NUMBER REVISION DATE 05 FIRMWARE ADS-HCX(RSA)-HAA-[ADS-HCX] HARDWARE ADS-HCX ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

15 HARDWIRE / COMPONENT LOCATOR - OF PAGE OF 9 05 C A B D 0B_v_[H] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

16 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF 9 05 M!! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M M3 M5 M4 JS HA ORANGE (NC) VS : IMMO CONNECTOR GREEN 7 PIN M WHITE MS (NC) HA RELAY VS VS4 : IMMO HARNESS GREEN 7 PIN : IGNITION CONNECTOR BROWN 7 PIN IGNITION HARNESS (B) M M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT RED/WHITE BLACK DOT GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 0 BROWN SILVER DOT - BRAKE (+) INPUT 0 BLACK/WHITE SILVER DOT PURPLE SILVER DOT GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY MS VS3 PARKING LIGHTS (-) BLUE - 3 HORN (-) ORANGE - 4 LOCK (-) WHITE/BLUE - 8 UNLOCK (-) WHITE/GREEN - 9 BRAKE (+) WHITE/BLACK - TACH (AC) BLUE - 05 HOOD SWITCH : IGNITION HARNESS BROWN 7 PIN : GREEN : GRAY 0 PIN FUSEBOX, DRIVER SIDE (D) : GREEN FRONT VIEW ABOVE DRIVER KICK PANEL (C) M B_v_[H] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN WARNING AS MODULE PROGRAMMING PROCEDURE WILL ONLY FUNCTION WITH THE VEHICLE S MASTER KEY, IT IS IMPORTANT TO OBTAIN ALL VALID KEYS IN ORDER TO IDENTIFY THE MASTER KEY. INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

17 HARDWIRE / COMPONENT LOCATOR - OF PAGE 4 OF 9 05 B A C 0B_v_[W] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

18 HARDWIRE / WIRING DIAGRAM - OF PAGE 5 OF 9 05 M!! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M M3 M5 M4 : GREEN M 0 ORANGE - ACCESSORY 0 RED - V PURPLE - ER PINK/WHITE 05 PINK - IGNITION 06 WHITE 07 RED - V 08 BLACK - GROUND KEY (DATA) RED/BLUE - 0 SECURITY LIGHT (-) BLUE/ORANGE M M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT RED/WHITE BLACK DOT GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 0 BROWN SILVER DOT - BRAKE (+) INPUT 0 BLACK/WHITE SILVER DOT PURPLE SILVER DOT GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 0 EMPTY BROWN/RED BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - KEY (DATA) 7 PINK 8 PURPLE 9 RED 0 BLACK ER (+) BLACK/WHITE - 0 V (+) WHITE - ACCESSORY (+) BLACK/RED - IGNITION (+) BLACK/YELLOW - 06 PARKING LIGHTS (-) BLUE - 3 HORN (-) ORANGE - 4 LOCK (-) WHITE/BLUE - 8 UNLOCK (-) WHITE/GREEN - 9 BRAKE (+) WHITE/BLACK - TACH (AC) BLUE - 05 HOOD SWITCH : BROWN : GREEN : GRAY 0 PIN : GREEN ABOVE DRIVER KICK PANEL (B) FUSEBOX, DRIVER SIDE (C) FRONT VIEW M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT - SECURITY LIGHT (-) CONNECTOR SIDE GRAY/RED BLUE DOT WHITE/RED BLUE DOT - SECURITY LIGHT (-) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT 0B_v_[W] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN WARNING AS MODULE PROGRAMMING PROCEDURE WILL ONLY FUNCTION WITH THE VEHICLE S MASTER KEY, IT IS IMPORTANT TO OBTAIN ALL VALID KEYS IN ORDER TO IDENTIFY THE MASTER KEY. INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

19 MODULE PROGRAMMING PROCEDURE - OF PAGE 6 OF ACC OFF ON Insert key into ignition. 07 Press and release the module s programming button. 0 ACC OFF ON Turn key to ON position. 08 Release the brake pedal. Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. ACC OFF ON Turn key to OFF position. 0 Module Programming Procedure completed. 05 ACC OFF ON vehicle for 5 seconds. 06 Press and hold the brake pedal. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

20 TAKEOVER PROCEDURE - OF PAGE 7 OF 9 05 >> All vehicle doors must be closed and locked prior to remote start sequence. 0 Press unlock on OEM or aftermarket remote or request switch. 0 OFF ACC ON DO NOT PRESS BRAKE PEDAL. Set ignition to ON position. Wait seconds for key validation. ENGINE STOP Press and release BRAKE pedal. Take over procedure completed. >> Failure to follow procedure will result in vehicle engine shutdown. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

21 INSTALLATION CHECKLIST - OF PAGE 8 OF 9 05 CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

22 INSTALLATION CHECKLIST - OF PAGE 9 OF 9 05 CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

23 INSTALL GUIDE Acura RSX STD key AT DOCUMENT NUMBER REVISION DATE 05 FIRMWARE ADS-HCX(RSA)-HAA-[ADS-HCX] HARDWARE ADS-HCX ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

24 HARDWIRE / COMPONENT LOCATOR - OF PAGE OF 9 05 C A B D 0A_v_[H] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

25 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF 9 05 M!! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M M3 M5 M4 JS HA ORANGE (NC) VS : IMMO CONNECTOR GREEN 7 PIN M 0 0 MS WHITE - PARKING LIGHT (+) (NC) HA RELAY VS VS4 : IMMO HARNESS GREEN 7 PIN : IGNITION CONNECTOR BROWN 7 PIN IGNITION HARNESS (B) M M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT RED/WHITE BLACK DOT GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT 0 BROWN SILVER DOT - BRAKE (+) INPUT 0 BLACK/WHITE SILVER DOT PURPLE SILVER DOT GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY MS VS3 UNLOCK (-) WHITE - LOCK (-) WHITE/RED - TACH (AC) BLUE - 05 BRAKE (+) WHITE/BLACK - PARKING LIGHTS (+) RED/YELLOW - 5 HORN (-) HOOD SWITCH : IGNITION HARNESS BROWN 7 PIN : WHITE : GREEN : GREEN : GREEN OEM ALARM MODULE (C) FUSEBOX, DRIVER SIDE (D) FRONT VIEW 3 M A_v_[H] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN WARNING AS MODULE PROGRAMMING PROCEDURE WILL ONLY FUNCTION WITH THE VEHICLE S MASTER KEY, IT IS IMPORTANT TO OBTAIN ALL VALID KEYS IN ORDER TO IDENTIFY THE MASTER KEY. INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

26 HARDWIRE / COMPONENT LOCATOR - OF PAGE 4 OF 9 05 C A B D 0A_v_[W] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

27 HARDWIRE / WIRING DIAGRAM - OF PAGE 5 OF 9 05 M!! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M M3 M5 M4 : GREEN M 0 ORANGE - ACCESSORY 0 RED - V PURPLE - ER PINK/WHITE 05 PINK - IGNITION 06 WHITE - PARKING LIGHT (+) 07 RED - V 08 BLACK - GROUND KEY (DATA) RED/BLUE - 0 SECURITY LIGHT (-) BLUE/ORANGE IGNITION HARNESS (B) M M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT RED/WHITE BLACK DOT GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT 0 BROWN SILVER DOT - BRAKE (+) INPUT 0 BLACK/WHITE SILVER DOT PURPLE SILVER DOT GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 0 EMPTY BROWN/RED BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - KEY (DATA) 7 PINK 8 PURPLE 9 RED 0 BLACK ER (+) BLACK/WHITE - 0 V (+) WHITE - ACCESSORY (+) BLACK/RED - IGNITION (+) BLACK/YELLOW - 06 UNLOCK (-) WHITE - LOCK (-) WHITE/RED - TACH (AC) BLUE - 05 BRAKE (+) WHITE/BLACK - PARKING LIGHTS (+) RED/YELLOW - 5 HORN (-) HOOD SWITCH : BROWN : WHITE : GREEN : GREEN : GREEN OEM ALARM MODULE (C) FUSEBOX, DRIVER SIDE (D) FRONT VIEW 3 M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT - SECURITY LIGHT (-) CONNECTOR SIDE GRAY/RED BLUE DOT WHITE/RED BLUE DOT - SECURITY LIGHT (-) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT 0A_v_[W] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN WARNING AS MODULE PROGRAMMING PROCEDURE WILL ONLY FUNCTION WITH THE VEHICLE S MASTER KEY, IT IS IMPORTANT TO OBTAIN ALL VALID KEYS IN ORDER TO IDENTIFY THE MASTER KEY. INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

28 MODULE PROGRAMMING PROCEDURE - OF PAGE 6 OF ACC OFF ON Insert key into ignition. 07 Press and release the module s programming button. 0 ACC OFF ON Turn key to ON position. 08 Release the brake pedal. Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. ACC OFF ON Turn key to OFF position. 0 Module Programming Procedure completed. 05 ACC OFF ON vehicle for 5 seconds. 06 Press and hold the brake pedal. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

29 TAKEOVER PROCEDURE - OF PAGE 7 OF 9 05 >> All vehicle doors must be closed and locked prior to remote start sequence. 0 Press unlock on OEM or aftermarket remote or request switch. 0 OFF ACC ON DO NOT PRESS BRAKE PEDAL. Set ignition to ON position. Wait seconds for key validation. ENGINE STOP Press and release BRAKE pedal. Take over procedure completed. >> Failure to follow procedure will result in vehicle engine shutdown. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

30 INSTALLATION CHECKLIST - OF PAGE 8 OF 9 05 CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

31 INSTALLATION CHECKLIST - OF PAGE 9 OF 9 05 CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

32 INSTALL GUIDE Honda CR-V STD key AT DOCUMENT NUMBER REVISION DATE 05 FIRMWARE ADS-HCX(RSA)-HAA-[ADS-HCX] HARDWARE ADS-HCX ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

33 HARDWIRE / COMPONENT LOCATOR - OF PAGE OF 9 05 C A B D 0C_v_[H] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

34 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF 9 05 M!! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M M3 M5 M4 JS HA ORANGE (NC) VS : IMMO CONNECTOR GREEN 7 PIN M 0 0 MS WHITE - PARKING LIGHT (+) (NC) HA RELAY VS VS4 : IMMO HARNESS GREEN 7 PIN : IGNITION CONNECTOR BROWN 7 PIN IGNITION HARNESS (B) M 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT RED/WHITE BLACK DOT GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT VS3 LOCK (-) WHITE/BLUE - 0 UNLOCK (-) WHITE/GREEN - : IGNITION HARNESS BROWN 7 PIN : GRAY PIN ABOVE DRIVER KICK PANEL (C) M3 M4 0 BROWN SILVER DOT - BRAKE (+) INPUT 0 BLACK/WHITE SILVER DOT PURPLE SILVER DOT GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY MS TACH (AC) BLUE - 05 BRAKE (+) WHITE/BLACK - 0 PARKING LIGHTS (+) RED/YELLOW - 09 HORN (-) HOOD SWITCH : GREEN : GREEN : GREEN FUSEBOX, DRIVER SIDE (D) FRONT VIEW 3 M C_v_[H] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN WARNING AS MODULE PROGRAMMING PROCEDURE WILL ONLY FUNCTION WITH THE VEHICLE S MASTER KEY, IT IS IMPORTANT TO OBTAIN ALL VALID KEYS IN ORDER TO IDENTIFY THE MASTER KEY. INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

35 HARDWIRE / COMPONENT LOCATOR - OF PAGE 4 OF 9 05 C A B D 0C_v_[W] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

36 HARDWIRE / WIRING DIAGRAM - OF PAGE 5 OF 9 05 M!! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M M3 M5 M4 : GREEN M 0 ORANGE - ACCESSORY 0 RED - V PURPLE - ER PINK/WHITE 05 PINK - IGNITION 06 WHITE - PARKING LIGHT (+) 07 RED - V 08 BLACK - GROUND KEY (DATA) WHITE - 0 SECURITY LIGHT (-) BLUE/ORANGE IGNITION HARNESS (B) M 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT RED/WHITE BLACK DOT GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT ER (+) BLACK/WHITE - 0 V (+) WHITE - ACCESSORY (+) BLACK/RED - IGNITION (+) BLACK/YELLOW - 06 LOCK (-) WHITE/BLUE - 0 UNLOCK (-) WHITE/GREEN - : BROWN : GRAY PIN ABOVE DRIVER KICK PANEL (C) M3 M4 0 BROWN SILVER DOT - BRAKE (+) INPUT 0 BLACK/WHITE SILVER DOT PURPLE SILVER DOT GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 0 EMPTY BROWN/RED BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - KEY (DATA) 7 PINK 8 PURPLE 9 RED 0 BLACK TACH (AC) BLUE - 05 BRAKE (+) WHITE/BLACK - 0 PARKING LIGHTS (+) RED/YELLOW - 09 HORN (-) HOOD SWITCH : GREEN : GREEN : GREEN FUSEBOX, DRIVER SIDE (D) FRONT VIEW 3 M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT - SECURITY LIGHT (-) CONNECTOR SIDE GRAY/RED BLUE DOT WHITE/RED BLUE DOT - SECURITY LIGHT (-) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT 0C_v_[W] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN WARNING AS MODULE PROGRAMMING PROCEDURE WILL ONLY FUNCTION WITH THE VEHICLE S MASTER KEY, IT IS IMPORTANT TO OBTAIN ALL VALID KEYS IN ORDER TO IDENTIFY THE MASTER KEY. INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

37 MODULE PROGRAMMING PROCEDURE - OF PAGE 6 OF ACC OFF ON Insert key into ignition. 07 Press and release the module s programming button. 0 ACC OFF ON Turn key to ON position. 08 Release the brake pedal. Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. ACC OFF ON Turn key to OFF position. 0 Module Programming Procedure completed. 05 ACC OFF ON vehicle for 5 seconds. 06 Press and hold the brake pedal. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

38 TAKEOVER PROCEDURE - OF PAGE 7 OF 9 05 >> All vehicle doors must be closed and locked prior to remote start sequence. 0 Press unlock on OEM or aftermarket remote or request switch. 0 OFF ACC ON DO NOT PRESS BRAKE PEDAL. Set ignition to ON position. Wait seconds for key validation. ENGINE STOP Press and release BRAKE pedal. Take over procedure completed. >> Failure to follow procedure will result in vehicle engine shutdown. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

39 INSTALLATION CHECKLIST - OF PAGE 8 OF 9 05 CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

40 INSTALLATION CHECKLIST - OF PAGE 9 OF 9 05 CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

41 INSTALL GUIDE Honda Civic Hybrid STD key AT DOCUMENT NUMBER REVISION DATE 05 FIRMWARE ADS-HCX(RSA)-HAA-[ADS-HCX] HARDWARE ADS-HCX ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

42 HARDWIRE / COMPONENT LOCATOR - OF PAGE OF 9 05 C A B D 0B_v_[H] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

43 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF 9 05 M!! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M M3 M5 M4 JS HA ORANGE (NC) VS : IMMO CONNECTOR GREEN 7 PIN M WHITE MS (NC) HA RELAY VS VS4 : IMMO HARNESS GREEN 7 PIN : IGNITION CONNECTOR BROWN 7 PIN IGNITION HARNESS (B) M M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT RED/WHITE BLACK DOT GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 0 BROWN SILVER DOT - BRAKE (+) INPUT 0 BLACK/WHITE SILVER DOT PURPLE SILVER DOT GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY MS VS3 PARKING LIGHTS (-) BLUE - 3 HORN (-) ORANGE - 4 LOCK (-) WHITE/BLUE - 8 UNLOCK (-) WHITE/GREEN - 9 BRAKE (+) WHITE/BLACK - TACH (AC) BLUE - 05 HOOD SWITCH : IGNITION HARNESS BROWN 7 PIN : GREEN : GRAY 0 PIN FUSEBOX, DRIVER SIDE (D) : GREEN FRONT VIEW ABOVE DRIVER KICK PANEL (C) M B_v_[H] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN WARNING AS MODULE PROGRAMMING PROCEDURE WILL ONLY FUNCTION WITH THE VEHICLE S MASTER KEY, IT IS IMPORTANT TO OBTAIN ALL VALID KEYS IN ORDER TO IDENTIFY THE MASTER KEY. INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

44 HARDWIRE / COMPONENT LOCATOR - OF PAGE 4 OF 9 05 B A C 0B_v_[W] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

45 HARDWIRE / WIRING DIAGRAM - OF PAGE 5 OF 9 05 M!! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M M3 M5 M4 : GREEN M 0 ORANGE - ACCESSORY 0 RED - V PURPLE - ER PINK/WHITE 05 PINK - IGNITION 06 WHITE 07 RED - V 08 BLACK - GROUND KEY (DATA) RED/BLUE - 0 SECURITY LIGHT (-) BLUE/ORANGE M M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT RED/WHITE BLACK DOT GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 0 BROWN SILVER DOT - BRAKE (+) INPUT 0 BLACK/WHITE SILVER DOT PURPLE SILVER DOT GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 0 EMPTY BROWN/RED BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - KEY (DATA) 7 PINK 8 PURPLE 9 RED 0 BLACK ER (+) BLACK/WHITE - 0 V (+) WHITE - ACCESSORY (+) BLACK/RED - IGNITION (+) BLACK/YELLOW - 06 PARKING LIGHTS (-) BLUE - 3 HORN (-) ORANGE - 4 LOCK (-) WHITE/BLUE - 8 UNLOCK (-) WHITE/GREEN - 9 BRAKE (+) WHITE/BLACK - TACH (AC) BLUE - 05 HOOD SWITCH : BROWN : GREEN : GRAY 0 PIN : GREEN ABOVE DRIVER KICK PANEL (B) FUSEBOX, DRIVER SIDE (C) FRONT VIEW M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT - SECURITY LIGHT (-) CONNECTOR SIDE GRAY/RED BLUE DOT WHITE/RED BLUE DOT - SECURITY LIGHT (-) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT 0B_v_[W] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN WARNING AS MODULE PROGRAMMING PROCEDURE WILL ONLY FUNCTION WITH THE VEHICLE S MASTER KEY, IT IS IMPORTANT TO OBTAIN ALL VALID KEYS IN ORDER TO IDENTIFY THE MASTER KEY. INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

46 MODULE PROGRAMMING PROCEDURE - OF PAGE 6 OF ACC OFF ON Insert key into ignition. 07 Press and release the module s programming button. 0 ACC OFF ON Turn key to ON position. 08 Release the brake pedal. Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. ACC OFF ON Turn key to OFF position. 0 Module Programming Procedure completed. 05 ACC OFF ON vehicle for 5 seconds. 06 Press and hold the brake pedal. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

47 TAKEOVER PROCEDURE - OF PAGE 7 OF 9 05 >> All vehicle doors must be closed and locked prior to remote start sequence. 0 Press unlock on OEM or aftermarket remote or request switch. 0 OFF ACC ON DO NOT PRESS BRAKE PEDAL. Set ignition to ON position. Wait seconds for key validation. ENGINE STOP Press and release BRAKE pedal. Take over procedure completed. >> Failure to follow procedure will result in vehicle engine shutdown. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

48 INSTALLATION CHECKLIST - OF PAGE 8 OF 9 05 CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

49 INSTALLATION CHECKLIST - OF PAGE 9 OF 9 05 CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

50 INSTALL GUIDE Honda Civic STD key AT DOCUMENT NUMBER REVISION DATE 05 FIRMWARE ADS-HCX(RSA)-HAA-[ADS-HCX] HARDWARE ADS-HCX ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

51 HARDWIRE / COMPONENT LOCATOR - OF PAGE OF 9 05 C A B D 0B_v_[H] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

52 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF 9 05 M!! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M M3 M5 M4 JS HA ORANGE (NC) VS : IMMO CONNECTOR GREEN 7 PIN M WHITE MS (NC) HA RELAY VS VS4 : IMMO HARNESS GREEN 7 PIN : IGNITION CONNECTOR BROWN 7 PIN IGNITION HARNESS (B) M M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT RED/WHITE BLACK DOT GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 0 BROWN SILVER DOT - BRAKE (+) INPUT 0 BLACK/WHITE SILVER DOT PURPLE SILVER DOT GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY MS VS3 PARKING LIGHTS (-) BLUE - 3 HORN (-) ORANGE - 4 LOCK (-) WHITE/BLUE - 8 UNLOCK (-) WHITE/GREEN - 9 BRAKE (+) WHITE/BLACK - TACH (AC) BLUE - 05 HOOD SWITCH : IGNITION HARNESS BROWN 7 PIN : GREEN : GRAY 0 PIN FUSEBOX, DRIVER SIDE (D) : GREEN FRONT VIEW ABOVE DRIVER KICK PANEL (C) M B_v_[H] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN WARNING AS MODULE PROGRAMMING PROCEDURE WILL ONLY FUNCTION WITH THE VEHICLE S MASTER KEY, IT IS IMPORTANT TO OBTAIN ALL VALID KEYS IN ORDER TO IDENTIFY THE MASTER KEY. INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

53 HARDWIRE / COMPONENT LOCATOR - OF PAGE 4 OF 9 05 B A C 0B_v_[W] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

54 HARDWIRE / WIRING DIAGRAM - OF PAGE 5 OF 9 05 M!! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IGNITION SWITCH (A) M M3 M5 M4 : GREEN M 0 ORANGE - ACCESSORY 0 RED - V PURPLE - ER PINK/WHITE 05 PINK - IGNITION 06 WHITE 07 RED - V 08 BLACK - GROUND KEY (DATA) RED/BLUE - 0 SECURITY LIGHT (-) BLUE/ORANGE M M3 M4 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT RED/WHITE BLACK DOT GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 0 BROWN SILVER DOT - BRAKE (+) INPUT 0 BLACK/WHITE SILVER DOT PURPLE SILVER DOT GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 0 EMPTY BROWN/RED BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE 5 BROWN 6 ORANGE/BLACK - KEY (DATA) 7 PINK 8 PURPLE 9 RED 0 BLACK ER (+) BLACK/WHITE - 0 V (+) WHITE - ACCESSORY (+) BLACK/RED - IGNITION (+) BLACK/YELLOW - 06 PARKING LIGHTS (-) BLUE - 3 HORN (-) ORANGE - 4 LOCK (-) WHITE/BLUE - 8 UNLOCK (-) WHITE/GREEN - 9 BRAKE (+) WHITE/BLACK - TACH (AC) BLUE - 05 HOOD SWITCH : BROWN : GREEN : GRAY 0 PIN : GREEN ABOVE DRIVER KICK PANEL (B) FUSEBOX, DRIVER SIDE (C) FRONT VIEW M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT - SECURITY LIGHT (-) CONNECTOR SIDE GRAY/RED BLUE DOT WHITE/RED BLUE DOT - SECURITY LIGHT (-) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT 0B_v_[W] ADS-HCX(RSA)-HAA-[ADS-HCX]-EN WARNING AS MODULE PROGRAMMING PROCEDURE WILL ONLY FUNCTION WITH THE VEHICLE S MASTER KEY, IT IS IMPORTANT TO OBTAIN ALL VALID KEYS IN ORDER TO IDENTIFY THE MASTER KEY. INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.

55 MODULE PROGRAMMING PROCEDURE - OF PAGE 6 OF ACC OFF ON Insert key into ignition. 07 Press and release the module s programming button. 0 ACC OFF ON Turn key to ON position. 08 Release the brake pedal. Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. ACC OFF ON Turn key to OFF position. 0 Module Programming Procedure completed. 05 ACC OFF ON vehicle for 5 seconds. 06 Press and hold the brake pedal. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

56 TAKEOVER PROCEDURE - OF PAGE 7 OF 9 05 >> All vehicle doors must be closed and locked prior to remote start sequence. 0 Press unlock on OEM or aftermarket remote or request switch. 0 OFF ACC ON DO NOT PRESS BRAKE PEDAL. Set ignition to ON position. Wait seconds for key validation. ENGINE STOP Press and release BRAKE pedal. Take over procedure completed. >> Failure to follow procedure will result in vehicle engine shutdown. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

57 INSTALLATION CHECKLIST - OF PAGE 8 OF 9 05 CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

58 INSTALLATION CHECKLIST - OF PAGE 9 OF 9 05 CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. ADS-HCX(RSA)-HAA-[ADS-HCX]-EN

59 INSTALL GUIDE 0-0 Honda Element STD key AT DOCUMENT NUMBER REVISION DATE 05 FIRMWARE ADS-HCX(RSA)-HAA-[ADS-HCX] HARDWARE ADS-HCX ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.