Instruction Sheet. 22 Inch Reels. 18 Inch Reels. 11 Blade L.H G-Plex, E-Plex Eclipse Eclipse 122F

Transcription

1 INCLUDES ITEMS Rev E Instruction Sheet Inch Reels Blade L.H G-Plex, E-Plex 60 - Eclipse 60 - Eclipse F 9 Blade L.H G-Plex, E-Plex Eclipse 7 Blade L.H G-Plex, E-Plex Eclipse Inch Reels Blade L.H Eclipse F WARNING If incorrectly used, this machine can cause severe injury. Those who use and maintain this machine should be trained in its proper use, warned of its dangers and should read the entire manual before attempting to set up, operate, adjust, or service the machine. When Performance Matters.

2 This kit is intended for use with the Eclipse, G-Plex, E-Plex Triplex Greens Mowers and Eclipse floating reel walk behind units.! CAUTION Before you install this kit, read the mower s Safety & Operation Manual to become familiar with the mower, the controls and proper use of the equipment. Stay alert for potential hazards and follow all safety precautions. Read all instructions completely and make sure you understand them before proceeding with the assembly.. Park the unit on a flat and level surface, engage the parking brake, turn the ignition switch to the OFF position and remove the key. a. Wait for all movement to stop before making any adjustments or modifications. b. Allow sufficient time for the unit to cool down. c. Take this opportunity to thoroughly inspect the equipment and perform other required maintenance. Front Roller and Accessories The front roller is not included with the reel assembly and must be ordered separately. Check with your dealer for front rollers that are available for your unit. Follow installation instructions included with the front roller. Other accessories may also be available for your reel such as Turf Groomer, roller scrapers, and roller brushes. Install these accessories before installing reels. Follow instructions included in your mower s manuals and/or Turf Groomer s Instruction Sheet for adjusting the reel to bedknife and height of cut. Mounting the Cutting units on G-Plex and E-Plex Mowers. Before mounting the cutting units make sure the latches on the pull frames are in the opened position.. Position the cutting head at the front of the pull frame. Align the screw and bushing on each side of the cutting head below and slightly to the front of the slots on the pull frame. Push down on the pull frame and roll the cutting head back slightly until the bushing (on the cutting head) is positioned in the slot.. Pull the latch handle and pivot it to the rear (allow the bolt head to drop into the center hole) the latch will pivot forward and lock the bushing into place. [See Figure L] Repeat procedure on opposite side of the cutting head. Install the remaining cutting units using the same procedures.. Follow directions given with motor adapter kits for assembling motor to reels.. E-Plex Units - Connect the motor harness into the main harness at the top of the pull frame.! WARNING Before you attempt to clean, adjust, or repair any of this equipment, disengage all drives, shut down the engine and allow the unit to cool. Remove the key from the ignition switch and disconnect the power connector to prevent accidental discharge and potential bodily injuries.. PULL HANDLE UNTIL THE HEAD OF BOLT CLEARS THE HOLE LATCH LOCKED TO BUSHING. PIVOT FORWARD SHOWN AS REFERENCE ONLY LATCH IN THE OPEN POSITION Figure - Quick Detach Latch SHOWN AS REFERENCE ONLY Figure - Cutting Head Mounted To Pull Frame Litho in U.S.A. -009

3 Eclipse F and F. Remove existing reel from Eclipse mower. a. Remove the two shoulder bolts (A) and pivot the lift hangers (B) up and away from the reel. b. Remove motor mounting hardware (C) and slide reel motor (D) off end of reel shaft. Remove coupler (E) from reel shaft. c. Remove hairpin and flat washer (F) and lift panhard rod (G) off of reel bolt. NOTICE Gas Engine Power Modules: Do not leave the mower tipped back for an extended length of time or oil may migrate into the combustion chamber. d. Tip the unit back onto the handle and slide the reel away from the mower.. Remove hardware (H) and Panhard rod bracket (J) from existing reel and assemble to new reel assembly.. Tip unit back onto the handle and slide the new reel into position under mover.. Assemble Panhard rod (G), flat washer and hairpin (F) to reel.. Assemble coupler (E) to reel. Check to be certain key (K) is in position and slide motor (D) onto reel. Secure with hardware (C). 6. Pivot lift hangers (B) down and secure to reel assembly using shoulder bolts. D C K E B J F G H B A Figure Eclipse. If any existing reels are installed, remove them from the mower.. Assemble coupler (A), and O-ring (B) to reel. Check to be certain key (E) is in position and slide motor (D) onto reel. Secure with hardware (C).. Position reels under lift arms.. Start the unit, and fully lower the lift arms. Shut mower off and remove the key.. Assemble reels to lift arms using shoulder bolts (F). 6. Connect reel motor to mower harness. Hand tighten motor connections only, do not use wrenches to tighten motor connection. If connector does not assembly easily, check to be sure that connector is properly aligned to motor, and there is no debris in either side of connector. D C E B A F Figure

4 INCH REEL Reel Assembly Serial No. All To prevent injury, disengage all drives, engage parking brake and stop engine before working in machine or emptying grass catchers.! DANGER 6! WARNING To prevent cuts use socket wrench or Turf Groomer knob to turn reel Inch Standard Style Bedknives (Secured with screws) Part Number Description Low Profile 007 High Profile Standard Bedknife Inch Standard Style Bedknives (Secured with screws) Part Number Description 000 Medium Section 077 High Profile 07 Low Profile 079 Tournament 007 Super Tournament 606 and Standard Bedknife 607 and Standard Bedknife 60 and 67 - Standard Bedknife 60 - Standard Bedknife Optional MagKnife Bedknives Part Number Description 7 Low Profile 7 Tournament 00 Super Tournament 69 High Profile 00 Low Profile 70 Tournament 00 Super Tournament

5 INCH REEL Item Part No. Qty. Description Serial Numbers/Notes 0077 Frame, Inch Reel 700 Frame, Inch Reel 677 Decal, Danger Not used on Eclipse Reels Decal, Warning Not Used on Eclipse Reels 000 inch 7 Blade Left Hand Reel Used on 606 and inch 9 Blade Left Hand Reel Used on 607 and inch Blade Left Hand Reel Used on 60, 60, and Inch Blade Left Hand Reel Used on Bearing Housing 6 00 Bearing, Cup and Cone Seal, Grease 7 Grease Fitting 9 7 Vent Fitting 0 79 Nut, /6- Spiralock Flange Used on 606~60, 67~ Stop, Mower Used on 606~60, 67~677 0 Snap Ring 676 Spacer 000 Inch Bedknife Backing 0 Inch Bedknife Backing See Chart Bedknife Screw, /-0 x / in. Flat Head 7 9 Bolt, 7/6 x / in. 770 Coupling Used on 67 ~ 677 Only 9 79 Nut, /6- Hex Flat Washer, / Bearing Housing 00 Bearing, Cup and Cone 696 Seal, Grease 7 Grease Fitting 70 Vent Fitting 6 00 Spring, Compression Nut, Reel 0 Flat Washer, / 9 69 Seal Screw, /6- x -/ in. Hex Head 6 Lockwasher, / Heavy 07 Washer 66 Bolt, Shoulder 009 Screw, /- x in. Hex Head 0 Screw, /-6 x -/ in. Square Hd 6 00 Screw, /6- x / in. Hex Head Used on 606~60, 67~677 > Change from previous revision

6 INCH REEL Outer Reel Assembly Serial No. All Eclipse Reel 9 G-Plex E-Plex Reel

7 INCH REEL Item Part No. Qty. Description Serial Numbers/Notes Inch Rear Roller Used on 677 Only Inch Rear Roller All Inch Reels, Except Inch Rear Roller Used on 609 Only 00 Zerk Bolt 0069 Knob, Front Roller Adjusting 67 Carriage Bolt, /6- x -/ in. 79 Nut, /6- Spiralock Flange 6 07 Screw, /-0 x / in. Truss Head Casting, Counterweight Used on 67 ~ Casting, Counterweight Used on Eclipse Reels 60 Lockwasher, / Heavy Screw, /-0 x 7/ in. Hex Head Used on 67 ~ Screw, /-0 x -/ in. Hex Head Used on Eclipse Reels Shield, Inch Reel 0 07 Shield, Inch Reel 7 Decal, Danger Used on Eclipse Reels Only 0 Nut, /-0 Hex 0 Flat Washer, / 66 Stud 77 Screw, /-0 x 7/ in. Sq Hd Set 6 00 Roller Bracket Roller Bracket 6700 Adapter, Motor Used on Eclipse Reels Only 9 79 Seal, O-Ring Used on Eclipse Reels Only 0 0 Screw, /6- x / in. Socket Head Used on Eclipse Reels Only > Change from previous revision 9

8 INCH REEL Rear Roller Part Number Item Part No. Qty. Description Serial Numbers/Notes 006 Shaft, Roller 006 Tube, Roller 0066 Seal, Grease 0006 Bearing, Cup and Cone 0009 Seal, Grease Sleeve, Wear 7 0 Locknut, /6- HEC HD Washer > Change from previous revision

9 Rear Roller Part Number and 090 INCH REEL Item Part No. Qty. Description Serial Numbers/Notes N/S Tube, Roller 00 Inch Roller Shaft 09 Inch Roller Shaft 006 Seal 007 Bearing > Change from previous revision

10 MOTOR ADAPTER KIT Greensplex Greensmower Reel Motor Adapter Kit Part No Note: This cutting head requires the Motor Adapter Kit 999. Check to make sure your Greensplex Greensmower has this Motor Adapter Kit before installing the cutting head. If your Greensplex Greensmower does not have this Motor Adapter, you need to order a Motor Adapter kit Part No Item Part No. Qty. Description Serial Numbers/Notes 999 Greensplex Reel Motor Adapter Kit 067 Flat Washer, 6 06 Lockwasher, /6 060 Screw, /6- x -/ 770 Coupling, Drive 7 Adapter Plate 6 79 Seal, O-Ring.9 I.D. x Seal, O-Ring.99 I.D. x.07 > Change from previous revision 6

11 E-Plex Electric Greensmower Motor Adapter Kit Part Number 9996 MOTOR ADAPTER KIT Note: This cutting head requires the Motor Adapter Kit Check to make sure your E-Plex Electric Greensmower has this Motor Adapter Kit before installing the cutting head. If your E-Plex Electric Greensmower does not have this Motor Adapter, you need to order a Motor Adapter kit Part No Item Part No. Qty. Description Serial Numbers/Notes 9996 E-Plex Motor Adapter Kit > 7067 Adapter, Motor 79 Seal, O-Ring.9 I.D. x Guard, Motor 900 Coupling, Drive > Change from previous revision 7

12 Equipment from Jacobsen is built to exacting standards ensured by ISO 900 and ISO 00 registration at all of our manufacturing locations. A worldwide dealer network and factory trained technicians backed by Genuine Jacobsen Parts provide reliable, high-quality product support. When Performance Matters. Jacobsen, A Textron Company 0 Quality Drive, Charlotte, NC