CADDY ROD LOCK THREADED ROD MOUNTING SYSTEM BUILD. Assemble on the ground or off-site LIFT. Raise assembly to ceiling DONE. Level, tighten lock nut

Transcription

1 CDDY ROD OCK TREDED ROD MOUNTING SYSTEM BUID ssemble on the ground or off-site IT Raise assembly to ceiling DONE evel, tighten lock nut

2 CDDY ROD OCK Threaded Rod Mounting System P. 3-4 CDDY ROD OCK Beam Clamps ast, easy solution for attaching threaded rod assemblies to metal beam structures. P. 5 CDDY ROD OCK nchor Screw Push-to-install threaded rod support for concrete or brick. P. 6 CDDY ROD OCK Plywood orm Preset nchor Preset anchors for concrete over plywood forms that allow complex prefabricated threaded rod assemblies to be easily pushed into place. T he CDDY ROD OCK family of products allows contractors to prefabricate complex assemblies at ground level or off site, and then easily lift and lock them into place by pushing the threaded rod supports into the CDDY ROD OCK device. This ingenious technology works with threaded rod with burrs or imperfections, helping to eliminate clean-up time or the need to replace damaged threaded rod. The most unique feature of the system is its breakthrough push-to-install design. There is no need to spin the rod or attachment hardware to fix the assembly in place CDDY ROD OCK technology simply pushes onto the threaded rod. ine adjustments are still possible, ensuring a quality installation. Simply speaking CDDY ROD OCK is revolutionizing how contractors support conduit, cable tray, lights, ductwork and pipe by helping to make installations faster, easier and more secure. P. 7 P P. 11 P. 12 CDDY ROD OCK Nut n innovative nut that you push into place on threaded rod. CDDY ROD OCK Duct Brackets Elegant solutions to facilitate pre-fabrication of rectangular duct. CDDY ROD OCK -Bracket Solution for attaching threaded rod assemblies to the side of vertical structures. CDDY ROD OCK Telescoping Strut Replacement Extremely fast and simple solution for multi-tiered trapeze installations. CDDY ROD OCK Channel Nut ttaches threaded rod to standard strut profiles. P. 13 SN Series Nut Innovative slotted design allows side mounting of the nut to threaded rod. Ideal for retrofit projects. P

3 CDDY ROD OCK Beam Clamp Prefabricated assemblies easily lift and lock into place, helping to save time and money Easy push-to-install design allows installers to simply push the threaded rod through the mounting hole, instantly holding it in position ock nut can be finger tightened, locking the rod in place orks with slightly damaged threads and minor burrs on the threaded rod Conforms with ederal Specification (Type 23), Manufacturers Standardization Society NSI /MSS-SP-58 (Type 19 and 23) T Material: Cast iron inish: Electro-galvanized rticle Number lange Thickness T eight ength idth Static oad 1 1 Static oad 2 2 Certifications CRBM8EG M mm 30 mm 52.3 mm 25.3 mm 24.9 mm 1,100 N 1,400 N cuus, VdS CRBM10EG M mm 30 mm 52.3 mm 25.3 mm 24.9 mm 1,100 N 2,200 N cuus, M, VdS lange Thickness T eight ength idth Static oad 1 1 Static oad 2 2 CRB37EG 3/8 1/8 3/8 1 3/ lb 500 lb Static oad 1 represents 1/8 to 3/16 (3 mm to 5 mm) flange thickness. Static oad 2 represents 1/4 to 3/8 (6 mm to 10 mm) flange thickness. or use on plain and electro zinc plated hardware only. 3

4 CDDY ROD OCK Beam Clamp, ide Mouth T Prefabricated assemblies easily lift and lock into place, helping to save time and money Easy push-to-install design allows installers to simply push the threaded rod through the mounting hole, instantly holding it in position ock nut can be finger tightened, locking the rod in place orks with slightly damaged threads and minor burrs on the threaded rod Conforms with ederal Specification (Type 23), Manufacturers Standardization Society NSI /MSS-SP-58 (Type 19 and 23) Material: Cast iron inish: Electro-galvanized rticle Number lange Thickness T eight ength idth Static oad CRBM12EG M mm 54 mm 61.6 mm 33 mm 25.5 mm 4,400 N lange Thickness T eight ength idth Static oad CRB50EG 1/2 3/8 3/ ,100 lb M pproved for top mount applications only. or use on plain and electro zinc plated hardware only. 4

5 CDDY ROD OCK nchor Screw or use with concrete and solid brick Prefabricated assemblies easily lift and lock into place, helping to save time and money orks with slightly damaged threads and minor burrs on the threaded rod B C inish: Electro-galvanized rticle Number B C Drill Bit Size Drill ole Depth Static oad Certifications CRM8EG M8 72 mm 32 mm 22 mm 8 mm 50 mm 2,900 N CRM10EG M10 72 mm 32 mm 22 mm 8 mm 50 mm 2,900 N M B C Drill Bit Size Drill ole Depth Static oad CR37EG 3/8 2 7/8 1 1/4 7/8 5/ lb or use on plain and electro zinc plated hardware only. Tested in 3000 psi (20.67 Mpa) concrete. 5

6 CDDY ROD OCK Plywood orm Preset nchor Ø Ø 1 2 Eliminate overhead drilling into building structure CDDY ROD OCK Preset nchors are cast in place Nails hold the anchor in place during the pour and easily break off with a strike of a hammer once the plywood forms are removed Easy push-to-install design allows installers to simply push the threaded rod through the mounting hole, instantly holding it in position orks with slightly damaged threads and minor burrs on the threaded rod Prefabricated assemblies easily lift and lock into place, helping to save time and money Plastic flange acts as insert locator when the forms are removed Suitable for use in seismic zones inish: Electro-galvanized rticle Number Diameter Ø eight 1 1 eight 2 2 Static oad CRM10EG M mm 82.3 mm 61.0 mm 6,300 N CRM12EG M mm 84.8 mm 63.5 mm 7,200 N Diameter Ø eight 1 1 eight 2 2 Static oad CR37EG 3/ ,407 lb CR50EG 1/ ,605 lb 6

7 CDDY ROD OCK Nut Easy push-to-install design allows installers to simply push the threaded rod through the mounting hole, instantly holding it in position ast installation onto long threaded rods push the nut in place instead of threading it up the rod Excellent alignment and easy fine adjustment by spinning the nut Extremely useful in tight spaces where wrenches are difficult to use inish: Electro-galvanized rticle Number eight idth Static oad CRNM8EG M8 20 mm 27.3 mm 4,500 N CRNM10EG M10 20 mm 27.3 mm 6,000 N eight idth Static oad CRN37EG 3/ ,350 lb 7

8 CDDY ROD OCK Top-Mount Duct Bracket llows duct to be mounted tight against the ceiling to maximize overhead space and reduce the amount of threaded rod required Multiple horizontal mounting slots accommodate insulated duct in tight spaces orks with studs in addition to threaded rods for a more aesthetic installation Slotted holes in bracket allow for horizontal adjustment of the bracket relative to the duct Easy push-to-install design allows installers to simply push the threaded rod through the mounting hole, instantly holding it in position Ready to use out of the box and eliminates the need for cutting and preparing sections of strut, angle iron, or strap Integrated adjustment nut enables fine tuning the system height up or down ock nut can be finger tightened, locking the rod in place Ideal for modular assembly allows attachment of brackets to sections of duct while safely on the ground Extremely useful in tight spaces where wrenches are difficult to use Includes self-tapping sheet metal screws to attach bracket to duct inish: Electro-galvanized rticle Number eight ength idth Static oad CRDM8TEG M8 112 mm 37.8 mm mm 63.5 mm 2,900 N CRDM10TEG M mm 37.8 mm mm 63.5 mm 2,900 N eight ength idth Static oad CRD37TEG 3/ / /2 650 lb 8

9 CDDY ROD OCK Bottom-Mount Duct Bracket Ideal for modular assembly allows attachment of brackets to sections of duct while safely on the ground Slotted holes in bracket allow for horizontal adjustment of the bracket relative to the duct Easy push-to-install design allows installers to simply push the threaded rod through the mounting hole, instantly holding it in position Ready to use out of the box and eliminates the need for cutting and preparing sections of strut, angle iron, or strap Integrated adjustment nut enables fine tuning the system height up or down ock nut can be finger tightened, locking the rod in place Extremely useful in tight spaces where wrenches are difficult to use Includes self-tapping sheet metal screws to attach bracket to duct inish: Electro-galvanized rticle Number eight ength idth Static oad CRDM8BEG M8 44 mm 89.5 mm mm 63.5 mm 2,900 N CRDM10BEG M10 44 mm 89.5 mm mm 63.5 mm 2,900 N eight ength idth Static oad CRD37BEG 3/ / /2 650 lb 9

10 CDDY ROD OCK Bottom-Mount Duct Bracket, Narrow Ideal for modular assembly allows attachment of brackets to sections of duct while safely on the ground Non-slotted bracket allows for attachment after the final horizontal position of the duct is achieved Easy push-to-install design allows installers to simply push the threaded rod through the mounting hole, instantly holding it in position Ready to use out of the box and eliminates the need for cutting and preparing sections of strut, angle iron, or strap Integrated adjustment nut enables fine tuning the system height up or down ock nut can be finger tightened, locking the rod in place Extremely useful in tight spaces where wrenches are difficult to use Includes self-tapping sheet metal screws to attach bracket to duct inish: Electro-galvanized rticle Number eight ength idth Static oad CRDM8BNEG M mm mm 53.3 mm 2,900 N CRDM10BNEG M mm mm 53.3 mm 6,200 N eight ength idth Static oad CRD37BNEG 3/ ,400 lb 10

11 CDDY ROD OCK -Bracket S1 S2 Easy push-to-install design allows installers to simply push the threaded rod through the mounting hole, instantly holding it in position Prefabricated assemblies easily lift and lock into place, helping to save time and money Multiple attachment holes support the use of either self-drilling screws or bolts, offering installation options for concrete, wood, and steel structures ock nut can be finger tightened, locking the rod in place Integrated adjustment nut enables fine tuning the system height up or down Extremely useful in tight spaces where wrenches are difficult to use Conforms with ederal Specification (Type 23), Manufacturers Standardization Society NSI /MSS-SP-58 (Type 19 and 23) inish: Electro-galvanized rticle Number eight ength idth ole Size 1 S1 ole Size 2 S2 rench Size Static oad Certifications CRM8EG M mm 43.2 mm 35.6 mm 10.4 mm 7.1 mm 24 mm 2,200 N VdS CRM10EG M mm 43.2 mm 35.6 mm 10.4 mm 7.1 mm 24 mm 3,100 N cuus, M, VdS eight ength idth ole Size 1 S1 ole Size 2 S2 rench Size Static oad CR37EG 3/8 2 1/ / lb ollow fastener manufacturer s recommended shear and pull-out strength when fastening to the structure. astener not included. Install in accordance with applicable code. 11

12 CDDY ROD OCK Telescoping Strut Replacement Easy push-to-install design allows installers to simply push the threaded rod through the mounting hole, instantly holding it in position Ready to use out of the box and eliminates the need for cutting sections of strut Telescopes to the desired length and then pushes onto the threaded rod Integrated adjustment nut enables fine tuning the system height up or down ock nut can be finger tightened, locking the rod in place llows for the quick creation, installation, and adjustment of multi-level trapeze assemblies Supports up to four 2 (50 DN) conduits or four 2 (50 DN) water filled pipes at 10 (3 m) spacing orks with the KBT ire Basket Tray Clip for securing wire basket cable tray orks with SC Single-Piece Strut Clamps B D C T E S inish: Pre-galvanized rticle Number ole Size S Thickness T B C D E Static oad TSR200M8R M8 6.4 mm 1 mm mm mm 35.6 mm 20.6 mm 28.4 mm 890 N TSR200M10R M mm 1 mm mm mm 35.6 mm 20.6 mm 28.4 mm 890 N ole Size S Thickness T B C D E Static oad TSR20038R 3/8 1/ lb 12

13 CDDY ROD OCK Channel Nut Provides fast universal attachment of threaded rod and hardware to standard strut profiles Can be used to prefabricate assemblies which can be quickly pushed onto previously installed threaded rods orks with slightly damaged threads and minor burrs on the threaded rod B C D Material: Cast iron inish: Electro-galvanized rticle Number B C D Static oad CRSM8EG M8 23 mm 35 mm 19.5 mm 13.5 mm 2,750 N CRSM10EG M10 23 mm 35 mm 19.5 mm 13.5 mm 3,750 N B C D Static oad CRS37EG 3/ lb or use on plain and electro zinc plated hardware only. 13

14 SN Series Nut llows side mounting of nut to threaded rod Reduces the need for threading compared to standard nuts and washers Ideal for retrofit projects, such as trapeze installations orks with slightly damaged threads and minor burrs on the threaded rod Reduces installation time up to 50% B inish: Electro-galvanized rticle Number B Static oad SNM M6 19 mm 22 mm 1,650 N SNM M8 19 mm 22 mm 4,500 N SNM M10 19 mm 22 mm 6,000 N SNM M12 19 mm 22 mm 10,000 N B Static oad SN25 1/4 3/4 7/8 500 lb SN37 3/8 3/4 7/8 1,350 lb SN50 1/2 3/4 7/8 2,250 lb or use on plain and electro zinc plated hardware only. 14

15 NSI is a registered trademark of merican National Standards Institute. M is a registered certification mark of M pprovals C, TD. U, UR, cu, cur, cuus and curus are registered certification marks of U C. RNING Pentair products shall be installed and used only as indicated in Pentair s product instruction sheets and training materials. Instruction sheets are available at and from your Pentair customer service representative. Improper installation, misuse, misapplication or other failure to completely follow Pentair s instructions and warnings may cause product malfunction, property damage, serious bodily injury and/or death, and void your warranty. 15

16 USTRI Phone ax CIN Phone ax UNGRY Phone ax NORY Phone ax SITZERND Phone ax BEGIUM Phone ax DENMRK Phone ax INDONESI Phone ax POND Phone ax TIND Phone ax BRZI Phone ax RNCE Phone ax ITY Phone ax SINGPORE Phone ax UNITED RB EMIRTES Phone ax CND Phone ax GERMNY Phone ax MEXICO Phone ax SPIN Phone ax UNITED KINGDOM Phone ax CIE Phone ax ONG KONG Phone ax NETERNDS Phone ax SEDEN Phone ax UNITED STTES Phone ax Pentair ll Rights Reserved Pentair, CDDY, CDED, CRITEC, ERICO, ERIEX, ERITEC and ENTON are owned by Pentair or its global affiliates. ll other trademarks are the property of their respective owners. Pentair reserves the right to change specifications without prior notice. M1243B-EN M509T15EN 2.5M1015