PD15-UL-M KIT INSTRUCTIONS
|
|
- Pearl Bradley
- 5 years ago
- Views:
Transcription
1 PD5-UL-M KIT INSTRUCTIONS The Command Access PD5-UL-M-KIT is a field-installable motorized latchpullback kit for the Jackson 85/95 & AHT 8/9 series devices. A. B. C. D. E. F. G. H. I. KIT INCLUDES TOOLS REQUIRED A. - B. - C. - D. - E. - F. 3- G. - H. - I Motor Mount 6064 MM4 RM series module (w/ optional REX) Phillips Screws Bracket Cable Mounting Pad Cable Guides Cable Ties 5074 MM4 RM Cable Lead Cordless Drill /6 drill bit File # Phillips head screwdriver PH-00 Screwdriver Watch the Video US customer support CA customer support #0379_J
2 Technical Information SPECIFICATIONS MM4 Switches off STANDARD TORQUE on on HIGH TORQUE PTS PROGRAMMING ON off PTS PROGRAMMING LOCKED Input Voltage: 4VDC +/- 0% Wire gauge: Minimum 8 gauge Direct wire run - no relays or access control units in-between power supply & module Standard Torque Mode Average Latch Retraction Current: Amp Average Holding Current: 5 ma High Torque Mode Average Latch Retraction Current: Amp Average Holding Current: 50 ma Step Step Step 3 Step 4 Beeps Setting PTS **Important Info** Make sure to set PTS before finishing installation Select your preferred torque mode (ships in standard torque) Press the device push pad to the desired setting. (Recommend to fully depress and release 5%, giving the device room for changing door conditions.) While depressing the push pad, apply power. (i.e. presenting the credential to the reader). Continue to keep pad depressed, the device will beep 6 times. After the beeps have stopped, release the pad and now the adjustment is complete. If not to your liking repeat the 3 steps. Once you ve found the correct location, flip the dip switch to off to lock programming. Beeps Explanation Solution Over Voltage Troubleshooting & Diagnostics > 30V unit will shut down. Check voltage & adjust to 4 V. 3 Beeps Under Voltage < 0V unit will shut down. Check voltage & adjust to 4 V. 4 Beeps Failed Sensor Verify all 3 sensor wires are installed correctly. Replace sensor if problem persists by contacting office. 5 Beeps 6 Beeps Retraction or dogging failure PUSH TO SET After st fail: 5 beeps then immediately attempts to retract again. After nd fail: 5 beeps with pause in-between for 30 seconds then device attempts to retract again. After 3rd fail: 5 beeps every 7 minutes, device will not attempt to retract. To Reset: Depress bar for 5 seconds at any time. Device is recording it s new position and power mode after the 6th beep. US customer support CA customer support
3 Electrified Exit Device INSTALLATION EXAMPLE CAT GREEN CHANNEL LED Ceiling Tile NORMALLY OPEN DRY CONTACT FROM ACCESS CONTROL SYSTEM NO VOLTAGE + - LOCKING HARDWARE Module Legend Standard Placement Recommended Power Supplies: All Command Access exit devices & field installable kits have been thoroughly cycle tested with Command Access power supplies at our factory. For more information click here or go to our website US customer support CA customer support
4 STEP - Disassemble Exit Device Remove () screws on push pad end caps from.. Pull back push pad exposing the front activating bracket. Remove guides and roll pin from activating front & back bracket. Once connecting rods are disconnected from front Remove head assembly by removing () screws. activating bracket flip device over. Slide push pad forward to remove from device Underneath pushpad remove dogging assembly. US customer support CA customer support
5 7. Re-attach head assembly by securing () screws. 8. CVR RIM Next, we ll be installing the kit in between the activating brackets on the exposed baserail. **Important Info** BEFORE MOVING TO STEP - SEE STEP C on PAGE 8 BEFORE AFTER STEP - Installing Kit PILOT HOLE PILOT HOLE IN INCHES ( ) / /4 AMOUNT REMOVED IN INCHES ( ) 5/8 5/6 9. Add bracket #50453 to front activating bracket. Dropping it over the top and securing it with the screw provided. 0. On the baserail, remove the back () screws from the dogging bracket.. Make sure scissor bracket on bottom side is diagonal & screws are flush before installing. FRONT US customer support CA customer support
6 Next, drop the motor mount in with the front over the front activating bracket. 3. Line up the back with the () available screw holes and the bracket securing the motor mount. 4. Push screws to correct position (pictured) to straighten scissor bracket and secure front end of the motor kit by tightening () screws.. 6. Tighten back end of the module by reinstalling () screws from dogging bracket. Push pad MM4 module into housing s channel on the 7. Slide back of the device. 8. Slide all the way up until the MM4 bracket is almost flush with end of the channel. Tighten all (4) screws here to secure MM4 End of el Chann 3 4 U S c u s t o m e r s u p p o r t w w w. c o m m a n d a c c e s s. c o m C A c u s t o m e r s u p p o r t
7 9. Connect MM4 Cable. Attach the strain relief and secure MM4 cable with a zip tie. 0.. Attach the wire guides to the inside of the baserail.. Route wires along the inside of the baserail using the wire guides. **HOOK UP TO POWER & TEST MOTOR BEFORE MOVING ON TO STEP 5.** STEP 3 - Reassemble Exit Device pins and connecting rods on both. Re-install activating brackets. Once guides & bumpers are installed on activating brackets slide on the push pad. Rod e f devic Back o Connecting Rod Front
8 3. Turn over BACK push pad end cap over and start a pilot hole beneath the bottom right hand corner (see measurements below). Use the gold bracket as a guide. Once your hole is drilled use your preferred method to clear out the remaining debris and file to clean up the edges. BEFORE AFTER PILOT HOLE PILOT HOLE IN INCHES ( ) / /4 4. AMOUNT REMOVED IN INCHES ( ) 5/8 5/6. Slide BACK push pad end cap into channel before re-installing to push pad.. Re-install () screws on BACK & FRONT push pad end caps. 5.. Slide filler plates on and plug into power.. Set Push-to-Set and once you found the correct location, turn PTS switch to OFF position. Step Step Step 3Step 4- Setting PTS Select your preferred torque mode (ships in standard torque) Press the device push pad to the desired setting. (Recommend to fully depress and release 5%, giving the device room for changing door conditions.) While depressing the push pad, apply power. (i.e. presenting the credential to the reader). MM4 Switches off on on off STANDARD TORQUE HIGH TORQUE PTS PROGRAMMING ON PTS PROGRAMMING LOCKED Continue to keep pad depressed, the device will beep 6 times. After the beeps have stopped, release the pad and now the adjustment is complete. If not to your liking repeat the three steps. Once you found the correct location, flip the dip switches to off to lock programming. U S c u s t o m e r s u p p o r t w w w. c o m m a n d a c c e s s. c o m C A c u s t o m e r s u p p o r t
PD10-UL-M KIT. I N S E R T I n s t r u c t i o n s A. B. C. D. E. E. E.
PD10-UL-M KIT I N S E R T I n s t r u c t i o n s The PD10-UL-M-KIT is a field installable motorized latch pullback for the PD10/11, Doromatic or Falcon 1690/1790, & First Choice 3600/3700. A. B. C. D.
More informationLLP-UL-M-KIT Series Motorized Electric Latch Retraction
LLP-UL-M-KIT I n s ta l l at I o n InstructIons The LLP-UL-M-KIT is a field installable motorized latch pullback kit for the Hager 4500 and Lawrence 8000 series. B. C. A. D. LLP-UL-M-KIT IncLU d e s A.
More informationslp-ul-m KIT INSERT Instructions A. B. C. E. F. G.
slp-ul-m KIT INSERT Instructis The Command Access SLP-UL-M-KIT is a field installable motorized latch-pullback kit for the Sargent 80 series. A. B. C. D. E. E. F. G. A. B. C. D. E. F. Kit Includes 1- Motor
More informationPD10-M-RIM INSTALLATION INSTRUCTIONS. The PD10-M-RIM is a storefront grade 1 exit device equipped with motor drive latch retraction.
PD10-M-RIM INSTALLATION INSTRUCTIONS The PD10-M-RIM is a storefront grade 1 exit device equipped with motor drive latch retraction. Retrofits Doromatic 1790 & First Choice 3790. B. G. A. C. D. E. F. PD10-M-RIM
More informationPD10-M-CVR INSTALLATION INSTRUCTIONS. Tools Required. PD10-M-CVR Includes
PD10-M-CVR INSTALLATION INSTRUCTIONS The PD10-M-CVR is a storefront grade 1 exit device equipped with motor drive latch retraction. Retrofits Doromatic 1690 & First Choice 3690. C. I. D. E. F. G. H. PD10-M-CVR
More informationVLP-UL-M-KIT INSTALLATION INSTRUCTIONS
VLP-UL-M-KIT INSTALLATION INSTRUCTIONS The Command Access VLP-UL-M-KIT is a field-installable motorized latch-pullback kit for the Von Duprin 33/35 & 98/99 series devices. F. G. i. H. j. K. D. Kit Includes
More informationVLP-UL-KIT INSTALLATION INSTRUCTIONS. The VLP-UL-KIT for 36 or 48 is a field installable solenoid latch pullback for the Von Duprin 33/35 &
Solenoid VLP-UL-KIT INSTALLATION INSTRUCTIONS The VLP-UL-KIT for 36 or 48 is a field installable solenoid latch pullback for the Von Duprin 33/35 & 98/99 series exit devices..050 Hex Wrench retraction
More informationPD18-RIM INSTALLATION INSTRUCTIONS
PD18-RIM INSTALLATION INSTRUCTIONS The PD18-RIM is a storefront grade 1 exit device equipped with motor driven latch retraction. Retrofits Adams Rite 8800 series. A. C. E. B. D. PD18-RIM Includes A. RIM
More information4500 Series Electric Exit Devices Request to Exit (RX) Installation Instruction Grade 1 I-ED00368
4500 Series Electric Exit Devices Request to Exit (RX) Installation Instruction Grade 1 I-ED00368 DEVICES COVERED IN THESE INSTRUCTIONS: RX Request to Exit ELECTRICAL SPECIFICATIONS Note: SPDT mechanical
More informationConflicts: JBL Audio, Factory Navigation, Accessory XM Satellite Radio, and Accessory Sirius Satellite Radio
TOYOTA YARIS SEDAN 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts: JBL Audio, Factory Navigation,
More informationAutomatic Roof Hatch Opener
Automatic Roof Hatch Opener Installation Guide REQUIRED TOOLS (These tools are required to complete the installation) Cordless Drill 1/8 1/4 Drill Bits 1/8 Pin Punch #2 Philips Bit Rachet Sharpie Hammer
More informationTOYOTA TUNDRA HANDS FREE BLU LOGIC Preparation
TOYOTA TUNDRA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationTOYOTA CAMRY HANDS FREE BLU LOGIC Preparation
TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationLGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions
LGT-312L E-Z-Go TXT 2014+ Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationPRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Security System Kit (sold separately) P/N 08E51-EP4-101
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30510 (LX) 2006 PILOT Issue Date SEP 2005 PARTS LIST Security System Kit (sold separately) P/N 08E51-EP4-101 Security system control
More informationETF-600 Sensor Operated Lavatory Faucet
INSTALLATION INSTRUCTIONS OPTIMA SYSTEMS SENSOR OPERATED LAVATORY FAUCET ETF-600 I.I. Code No. 0816318 ETF-600 Sensor Operated Lavatory Faucet Includes Instructions for Installation of Optional Back Checks
More informationAdjustable Light Kits E-Z-Go TXT All Models Installation Instructions
Adjustable Light Kits E-Z-Go TXT All Models 1996-2013 Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationModel 2300JL Installation Guide
Model 2300JL Installation Guide POWER ACCESS CORPORATION 4 HERSHEY DRIVE, DOCK 4 ANSONIA, CT 06401 800-344-0088 WEBSITE: www.power-access.com EMAIL: salesinfo@power-access.com 1 STANDARD PARTS MODEL 2300JL
More informationSCION tc 2014 FOG LIGHT KIT
Part #: PT413-21140 Conflicts: P/N PTR11-21100 Lowering Springs (CA only) Kit Contents: Wire Ties Self-Tapping Screws Switch Relay Fog Light Bezel, Left and Right Side Wire Harness Fog Lamp, Left and Right
More informationSCION TC HANDS FREE BLU LOGIC Preparation
SCION TC 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00099 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationModel 2300DL Installation Guide
Model 2300DL Installation Guide POWER ACCESS CORPORATION 4 HERSHEY DRIVE, DOCK 4 ANSONIA, CT 06401 800-344-0088 WEBSITE: www.power-access.com EMAIL: salesinfo@power-access.com 1 STANDARD PARTS MODEL 2300DL
More informationTOYOTA TACOMA HANDS FREE BLU LOGIC Preparation. Item 5 Item 6 Item 7 Item 8. Item 4. General Applicability Note: Recommended Tools
TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00098 Conflicts: JBL Audio, Factory Navigation Kit Contents: NOTE: Part number of this accessory may not be the same as the part number
More informationSCION XB HANDS FREE BLU LOGIC Preparation
SCION XB 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationM-9603-FST FOCUS ST COLD AIR INTAKE KIT INSTALLATION INSTRUCTIONS
M-9603-FST Please visit www.fordracingparts.com for the most current instruction information.!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND
More information* * E996L Series. E996L for Rim/Vertical. E996L for Mortise CAUTION
*921297-00* 921297-00 Electric Locking Trim E996L Series Installation Instructions CAUTION Product is shipped in Fail Safe (FS) configuration. Fail Safe configuration is required by code in some applications
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S Application 2013 ACCORD 4-DOOR Publications No. AII 13026 Issue Date AUG 2012 PARTS LIST Aluminum tape Backup Sensors Attachment Kit P/N 08V67-T2A-100A Control unit
More informationA S S E M B L Y & I N S T A L L A T I O N G U I D E
A S S E M B L Y & I N S T A L L A T I O N G U I D E APPLICATION 2015-2016 2015-2016 PART # 7416-00A Silver 7416-01A Black INSTALLATION TIME 1 Hour 1 SKILL LEVEL 2 3 4 1= Easy TOOLS REQUIRED Phillips screw
More informationReplacing Your 2nd Generation Battery Pack
Replacing Your 2nd Generation Battery Pack Video tutorial: https://www.youtube.com/watch?v=xvcfwpo8rok Tools needed: 4mm hex tool. If you do not have a hex wrench, please email us at recall@boostedboards.com
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08E10-T2A-100A Application 2013 ACCORD 4-DOOR Publications No. AII 13002 Issue Date SEP 2012 PARTS LIST 2 Self-tapping screws, 5 x 16 mm bracket 2 Self-tapping
More informationTOYOTA VENZA HANDS FREE BLU LOGIC Preparation
TOYOTA VENZA 2009- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationIf technical support is required, please contact Advent Technical Support at
Document 128-9015A Created 12/12/11 Kit Contents: Item # Qty. Component Description 1 2 Headrest Assembly 2 2 Cables # 3 3 1 Power Cord # 9 4 1 FM Antenna 5 1 Control Box 6 2 IR Headphones 7 2 Remote Control
More informationMotorized Electric Latch Retraction
; SECTION I: OVERVIEW 1. Description The Corbin Russwin MELR Electric Latch Retraction (ELR), refer to Figure 1, works with ED4000 & ED5000 Series exit devices to provide remote-controlled latch retraction
More information2904 Power Supply Installation Instructions I-EA00041
FEATURES Controls an opening with electrified locking device and automatic door operator Separate inputs for activation switch on entry and exit sides of opening Separate 24 VDC outputs for fail safe and
More informationUniversal Tall HoneyBadger Chase Rack Installation Instructions
PREPARATION Universal Tall HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend
More informationSCION XB HANDS FREE BLU LOGIC Preparation. Item 4 Item 5 Item 6 Item 7. General Applicability. Note: Recommended Tools
SCION XB 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00090 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: Item 1 Item 2 Item
More information200 Shadylane Drive Philipsburg, PA Phone: (814) Fax: (814) Service Manual. Model 642E Centrifuge
200 Shadylane Drive Philipsburg, PA 16866 Phone: (814) 342-6205 Fax: (814) 342-4510 www.druckerdiagnostics.com Service Manual Model 642E Centrifuge MODEL 642E SERVICE MANUAL REV: Original Issue 1 CONTENTS
More informationValidator and Control Board Update Instructions for BC1
Validator and Control Board Update Instructions for BC1 Installation Overview The update kit for the Rowe BC1 enables the changer to interface with a Mars AE/VN 120-volt validator. The validator determines
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 12035 SYSTEM 2012 RIDGELINE Issue Date NOV 2011 PARTS LIST Security System Attachment Kit: P/N 08E55-SJC-101 Flange bolt Unit bracket
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S 1998 CIVIC 2/3/4-DOOR All 18767 Issue Date SEP 1997 PARTS LIST Fog Light Kit: P/N 08V31-S01-100 Right fog light (marked R ) Fuse label
More informationGateCrafters Automatic Gate Lock Instruction Manual GCLOCK
GateCrafters Automatic Gate Lock Instruction Manual GCLOCK Introduction The GateCrafters Automatic Gate Lock is designed to provide extra security and stability to your gate opener system. There are numerous
More informationIlluminated Cup Holders Hyundai Elantra (GLS, Limited, Coupe)
Illuminated Cup Holders 2011-2015 Hyundai Elantra (GLS, Limited, Coupe) Thanks for purchasing this Cup Holder Illumination Install Kit! If you have any questions or feedback please email me direct at info@accentglowled.com
More informationII E INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT
II E1500-11 INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT KITS ARE UL LISTED UNDER CATEGORY GWVW, GWVW7 (CANADA) (ACCESSORY FOR USE ON FIRE EXIT HARDWARE AND PANIC HARDWARE). INDEX
More informationINSTALLATION INSTRUCTIONS CRL JACKSON 2085E
INSTALLATION INSTRUCTIONS CRL JACKSON 2085E ELECTRIC LATCH RETRACTION CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2008 ACCORD 2-DOOR Publications No. AII 37561-38377 Issue Date NOV 2007 PARTS LIST Control unit bracket (L4) Back-up Sensor Attachment Kit P/N 08V67-TE0-100A
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM S2000 AII 26324 Issue Date OCT 2004 PARTS LIST Headrest Speaker System P/N 08A54-S2A-100 3 Small wire ties 2 Headrest speakers 9
More informationAlliance Towel Dispensing System. Operation Manual
Alliance Towel Dispensing System Operation Manual Alliance Towel Dispensing System Table of Contents Safety Information... page 2 Mounting Instructions... page 3 Towel Loading Instructions... page 7 Settings...
More informationSCION FR-S FOG LIGHTS
Part #: PT413-18130 Conflicts: Lowering Springs PTR07-18130-LL (California only) Kit Contents: For Anniversary Edition, Monogram & RS 2.0 vehicles, additional parts need to be ordered (PT413-18130-LL)
More informationHC-11 Programmer (optional)
A qualified technician must perform the installation. To avoid electrical shock or property damage, disconnect power before starting installation. Do not drop the sensor. If dropped, malfunctioning of
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publication No. INSTALLATION INSTRUCTIONS WINCH MOUNT KIT P/N 08L77-HL3-A00 SXS700M4/M2 Honda Dealer: Please give a copy of these instructions to your customer. MII 14607 Issue Date
More informationSmartLock Accessories
CANSEC ACCESSORIES SmartLock Accessories CA SLbox CA SLBOX SmartLock enclosure 9.5 x 13 x 3 metal enclosure with room for 1 or 2 SmartLock controllers, Cansec power supply and 12V 7 AH battery C Ca ps123a
More informationTOYOTA tc HANDS FREE BLU LOGIC Preparation
TOYOTA tc 2011- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24637 INSIGHT Issue Date OCT 2002 PARTS LIST Security System: P/N 08E51-S84-100 Attachment Kit: P/N 08E55-S3Y-100 Security system harness
More informationGeneral Applicability Note: Recommended Tools. Personal & Vehicle Protection Safety Goggles Seat Covers Floor Covers Special Tools. Installation Tools
TOYOTA HIGHLANDER/HIGHLANDER HV 2008- Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationINSTALLATION INSTRUCTIONS INFINITI CELLPORT UNIVERSAL HANDS FREE SYSTEM
INSTALLATION INSTRUCTIONS 1. DESCRIPTION: INFINITI CELLPORT UNIVERSAL HANDS FREE SYSTEM 2. APPLICATION: 2002 Q45 3. PART NUMBER: 948T3CELLR95 (VPC) or 999Q2TN000 (PDC) 4. TOOLS REQUIRED: a. Loctite 242
More informationAUDIO KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
AUDIO KIT P/N 2882696 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationKAWNEER 1686 EL CONCEALED EXIT DEVICE
FEBRUARY, 2012 1 ROD AND CENTER CASE ASSEMBLY: 1) For inactive doors or doors without exterior cylinder, or doors without the need for exterior cylinder dogging, the removal of the cylinder dogging pawl
More informationTOYOTA TUNDRA TVIP V4 Preparation
Preparation Part Number: PT398-00100 PT398-00100-AA Conflicts Do not install into vehicles without RKE system. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM
More informationTOYOTA PRIUS 2010 TVIP V4 PREPARATION
PREPARATION Part #: PT398-47091 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.
More informationIMPORTANT! Remote Control Instructions
Remote Control Instructions FOR New Tarp Remote Control Installation Use these in place of the rocker switch and solenoid section of instructions in your roll tarp owner s manual. FOR Existing Electric
More informationTOYOTA COROLLA 2010 TVIP V4 PREPARATION
PREPARATION Part #: PT398-02080 or PT398-02100 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts: Do not install into Manual Transmission Vehicles or Vehicles
More informationToyota Prius Dual Player Headrest Video ATTENTION: SECURITY COVERS ARE NO LONGER INCLUDED IN THE HEADREST KITS AS OF 01/17/2011
Toyota Prius 2011 - Dual Player Headrest Video Part Number: 00016-47210-01; 04; 11 Code : EH5 ATTENTION: SECURITY COVERS ARE NO LONGER INCLUDED IN THE HEADREST KITS AS OF 01/17/2011 Conflicts Kit Contents
More informationInstructions for 2-row monitoring only
Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only CAUTION: Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 25876 2004 PILOT (LX only) Issue Date AUG 2003 The subwoofer cannot be installed on a vehicle equipped with a navigation unit. Subwoofer
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More informationIceZone X Installation Instructions for Hoshizaki DCM-270 Ice and Water Dispensers
IceZone X Installation Instructions for Hoshizaki DCM-270 Ice and Water Dispensers This module will show the steps to install IceZone X on Hoshizaki DCM-270 Ice and Water Dispensers. Please review the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ENGINE BLOCK P/N 08T44-SWA-1A0 Application 2012 CIVIC 4-DOOR Si Publications No. AII 45627 Issue Date APRIL 2011 PARTS LIST Engine block heater Aluminum washer Heater
More informationTOYOTA COROLLA 2009 TVIP V4 PREPARATION
PREPARATION Part #: PT398-02080 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.
More informationInstructions for 2-row monitoring only
Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect installation
More informationInstallation for Manitowoc Indigo Ice Machines Standard Top-Mount Installation
Installation for Manitowoc Indigo Ice Machines Standard Top-Mount Installation This module will show the steps to install IceZone X on the Manitowoc Indigo Ice Machines. Please watch the entire video prior
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 39890 2009 MDX Issue Date JULY 2008 PARTS LIST Backup Sensor Attachment Kit P/N 08V67-STX-200A Self-tapping screw, 5 x 16 mm 12 Wire
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRAILER Application 2013 PILOT Publications No. AII 13332 Issue Date AUG 2012 PARTS LIST Trailer Harness Kit P/N 08L91-SZA-100A Relay cover Control unit harness 4 Wire
More informationONE TOUCH CONTROL BOX
ONE TOUCH CONTROL BOX CONVERSION KIT INSTRUCTIONS REMOVAL, INSTALLATION, OPERATION, AND REMOTE CONTROL PROGRAMMING THUNDERSTONE PART #101322 REVISION A JULY 14 TH 2016 2 P a g e INSTALLING THE THUNDER
More informationJEEP JK4 STEP SLIDER INSTALLATION BD-SS-100-JK4
JEEP JK4 STEP SLIDER INSTALLATION BD-SS-100-JK4 PARTS LIST QTY DESCRIPTION 1 Drivers Side Slider Assembly 1 Passenger Side Slider Assembly 1 Wiring Harness and Fuse 1 Double Sided Sticky Squares and Alcohol
More informationConf licts Note: TOYOTA Tacoma 2016 LED Illumination Package (Interior and Exterior) Part Number: Accessory Code: LL1000.
TOYOTA Tacoma 2016 LED Illumination Package (Interior and Exterior) Part Number: 00016-00069 Accessory Code: LL1000 Conf licts Note: Color Applicability/Trim Level Kit Contents Item # Quantity R eqd. Description
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRAILER Application 2012 PILOT Publications No. AII 46408 Issue Date AUG 2011 PARTS LIST Trailer Harness Kit P/N 08L91-SZA-100A Relay cover Control unit harness 4 Wire
More informationJEEP JK4 STEP SLIDER INSTALLATION BD-SS-100-JK4
JEEP JK4 STEP SLIDER INSTALLATION BD-SS-100-JK4 PARTS LIST QTY DESCRIPTION 1 Drivers Side Slider Assembly 1 Passenger Side Slider Assembly 1 Wiring Harness and Fuse 1 Double Sided Sticky Squares and Alcohol
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application CR-V Publications No. AII 32953-34081 Issue Date NOV 2006 PARTS LIST 2 Corner sensor clips Backup Sensor Attachment Kit P/N 08V67-SWA-100A Back-up sensor
More informationPH3 AIR INTAKE EMERGENCY SHUT-OFF VALVE WITH POWERGUARD SMART OVERSPEED LIMITER. Generic PH3 Truck Shut-Off Valve Kit.
PH3 AIR INTAKE EMERGENCY SHUT-OFF VALVE WITH POWERGUARD SMART OVERSPEED LIMITER Generic PH3 Truck Shut-Off Valve Kit www.powerhalt.com INSTALLATION REQUIREMENTS & RECOMMENDATIONS: Prior to the installation,
More informationSpectra Class. N6000 Series Exit Devices SECURITY DOOR CONTROLS. N6100 Rim Mount Exit Device. N6200 Surface Vertical Rod Exit Device.
N6000 Series Exit Devices Spectra Class Rim Mount Surface Vertical Rod N6100 Rim Mount Exit Device For use on single doors or pair of doors with mullion 1-3/4"(44 mm) door thickness standard. Specify thickness
More informationlkm7001 key override module Installation Instructions Converting The LKM7000 to The LKM7003
lkm7001 Instructions Converting The LKM7000 to The LKM7003 key override module In A Single Motion, We ll Change The Way You Think About Security Read Instructions thoroughly prior to installation Base
More informationInteli-Lift GEN II DUMBWAITER
1 877-345-4387 530-295-4900 www.eilifts.com Inteli-Lift GEN II DUMBWAITER The Easiest Dumbwaiter system on the Market Fully UL Certified Dumbwaiter Systems UL File # SA32120 This manual will cover the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08E10-TA0-110A Application 2012 ACCORD 2- AND 4-DOOR Publications No. AII 46501 Issue Date AUG 2011 PARTS LIST Ambient Light Kit Fuse label 2 Ambient lights Washer
More informationPRO LAUNCH INSTALLATION INSTRUCTIONS
12-339 4130 PRODUCT DRIVE, CAMERON PARK, CA 95682 PH: 1.530.642.9488 VIEW INSTALLATION VIDEO AT www.worksconnection.com/prolaunch/ 12-339 PRO LAUNCH INSTALLATION INSTRUCTIONS We at Works Connection Inc.
More informationTOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation
TOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation Part Number: PT297-35061 Kit Contents Item # Quantity Reqd. Description 1 2 Driving Lamp Assembly 2 1 Switch Harness 3 1 Lamp Harness 4 2 Stone Shield
More informationModel: PSB100. Rear Parking Sensor System. Installation Manual TABLE OF CONTENTS
Rear Parking Sensor System Model: PSB100 Installation Manual TABLE OF CONTENTS Warnings...2 Product Description...3 Packing List...3 Installation Instructions...4 Mounting the Sensors...4 Installing the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publication No. MII 15249 WINCH MOUNT KIT P/N 08L70-HL3-A41 SXS700/M4/M2 Issue Date September 2015 PARTS LIST No. Description Qty (1) Winch bracket 1 (2)
More informationHC-11 Programmer (optional)
To avoid electrical shock, disconnect power. Do not drop the sensor. If dropped, malfunctioning of the sensor may occur. LVE-10X OQM Installation Instructions Kit Numbers 140335 Est. Time 1 hour Tools
More informationInstallation Guide. Kennedy Technology Group, Inc.
Installation Guide Harley-Davidson Amp Module - Base Kit Kennedy Technology Group, Inc. 614 Ridgeway, Rose Hill, Kansas 67133 - USA voice 316.776.1111 fax 316.776.9035 email:kennedy@cellset.com www.cellset.com
More informationDesktop 5.5 Z Axis Retrofit
Page 1 Kit parts Desktop 5.5 Z Axis Retrofit Carriage plate with stop bolt and Z proximity switch installed Zip ties Spare bolts Spindle mounting plate with stop bolt, spring mount, and rail Z proximity
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08E10-TA0-100 Application 2008 ACCORD 2-AND 4-DOOR Publications No. AII 35358 Issue Date AUG 2007 PARTS LIST Ambient Light Kit 2 Ambient lights Fuse label Washer
More informationElectrical Options Booklet. Table of Contents
*24228413* 24228413 Electrical Options Booklet Table of Contents EL Wiring... EL Troubleshooting... SD/EL 98/99 Cylinder Dogging... SS Wiring... 330, 350, RX-330 and RX-350 Push Bar Trim Mechanical Installation...
More informationGeneral Applicability: KIA Sorento. Issues Current Kit does not allow for CAN DATA remote access
Document #730135 Created ACH 08/02/2018 Revised ACH 08/20/18 A2 General Applicability: 2018-19 KIA Sorento Issues Current Kit does not allow for CAN DATA remote access Kit Contents: Item# Component Description
More informationSafe-T-element Installation Instructions
Safe-T-element Installation Instructions For: PTI STEZA (2x2 Burner Configuration) & PTI STEZB (3x1 Burner Configuration) Revision K (May. 3 2012) TABLE OF CONTENTS 1. PREPARATION... 3 1.1 General Safety
More informationpg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers Installation
RZ3-5KRC RZR XP1000 & 2015+ RZR900 with Ride Command SSV Works 5 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers
More informationREARVIEW MIRROR AND BACKUP CAMERA KIT
REARVIEW MIRROR AND BACKUP CAMERA KIT P/N 2881483 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More informationJEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market
1 888-323-8755 www.nwlifts.com JEEVES Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market This manual will cover the installation procedure step-by-step. The installation of this dumbwaiter
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SECURITY SYSTEM P/N 08E49-SDA-100 ACCORD 2- AND 4-DOOR AII 30666 Issue Date AUG 2005 PARTS LIST Hood switch harness Illustration of the
More informationTOYOTA VENZA w/smart 2009 TVIP V4 PREPARATION
PREPARATION Part #: PT398-0T110 Conflicts: Will not program with Techstream Lite. Kit Contents RES ECU RES ECU Bracket RES Harness M6 Screw Wire Tie Splicing Connector Remote Label x1 x1 x1 x1 x5 x1 x2
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. KIT P/N 08E49-S9V-100 2003 PILOT LX AII 23629 Issue Date MAY 2002 PARTS LIST Illustration of the Security System installed on the Vehicle
More information