PD10-UL-M KIT. I N S E R T I n s t r u c t i o n s A. B. C. D. E. E. E.
|
|
- Claud Doyle
- 5 years ago
- Views:
Transcription
1 PD10-UL-M KIT I N S E R T I n s t r u c t i o n s The PD10-UL-M-KIT is a field installable motorized latch pullback for the PD10/11, Doromatic or Falcon 1690/1790, & First Choice 3600/3700. A. B. C. D. E. E. E. Kit Includes Tools Required A. B. C. D. E. F. G. Motor Mount w/mm4s Spring Attaching bracket 2 - Sets of finished phillips screws MM4S switch program sticker 1- Push & go connector 1-8 Lead w/ VD Connector Cordless Drill or Phillips Screwdriver Hacksaw Command Access Technologies La Palma Ave, Yorba Linda, CA Phone:(888)
2 Technical Information on on mm4s switches LOW TORQUE on STANDARD TORQUE on HIGH TORQUE PTS PROGRAMMING LOCKED SPECIFICATIONS Input Voltage: 24VDC +/- 10% Average Latch Retraction Current: 1 Amp Average Holding Current: 125 ma Wire gauge: Minimum 18 gauge PTS Video Click or Scan Low Torque Mode Average Latch Retraction Current: 600 ma Average Holding Current: 150 ma Standard Torque Mode Average Latch Retraction Current: 1 amp Average Holding Current: 215 ma High Torque Mode Average Latch Retraction Current: 2 Amp Average Holding Current: 250 ma Step 1- Select your preferred torque mode (ships in standard torque) Press the device push pad to the desired setting. (Recommend to fully depress and release 5%, giving the device room for changing door conditions.) Step 2- While depressing the push pad, apply power. (i.e. presenting the credential to the reader). Step 3- Step 4-2 Beeps Setting PTS **Important Info** Make sure to set PTS before finishing installation Continue to keep pad depressed, the device will beep 6 times. After the beeps have stopped, release the pad and now the adjustment is complete. If not to your liking repeat the 3 steps. Once you found the correct location, turn PTS switch to OFF position. Troubleshooting & Diagnostics Beeps Explanation Solution Over Voltage > 28V unit will shut down. Check voltage & adjust to 24 V. 3 Beeps Under Voltage < 22V unit will shut down. Check voltage & adjust to 24 V. 4 Beeps Failed Sensor Verify all 3 sensor wires are installed correctly. Replace sensor if problem persists by contacting CAT tech support. 5 Beeps Retraction or dogging failure Device will automatically re-engage within 5 seconds. 6 Beeps 6 Beeps PUSH TO SET PUSH TO SET Check to make sure the push pad is not stuck or catching on anything. If mechanical obstruction, remove & push pad down until beeping stops to reset. If no obstruction, the pad may have been pushed in too far during PTS calibration. Recalibrate with the pad slightly out. If problem persists, verify the magnet is within 1/4 of the sensor at the end of travel.
3 Module Electrified Exit Device Installation Example CAT GREEN CHANNEL 1 LED Ceiling Tile NORMALLY OPEN DRY CONTACT FROM ACCESS CONTROL SYSTEM NO VOLTAGE LOCKING HARDWARE + - Legend Standard Placement Optional Placement Retrofit 2-pin Connector The new 2-pin connector is used when retrofitting a older Command or Von Duprin installation so you can plug in to the exisiting connector. New Exisitng PUSH N GO Connector WIRE ACCESS Recommended Power Supplies: All Command Access exit devices & field installable kits have been thoroughly cycle tested with Command Access power supplies at our factory. For more information click here or go to our website
4 1. Remove end cap by unscrewing (2) screws. 2. Slide push pad device. Note: For AHT4/5 & PD11 s purchased after 2015 only. Remove baserail assembly first by removing 3. the 4 screws. 4. Remove both screws attaching head assembly to housing Remove dogging assembly screws. Remove back activating bracket screws as well. 6. Remove both screws attaching head assembly to housing. Activating bracket screws Possibly
5 7. Remove front activating bracket screws as well. Remove C clip connecting the head to the connecting rods. 8. For CVR skip this step. 9. Remove pin from connecting rod for RIM. For CVR skip this step. 10. CVR - Remove connecting rod assembly by pulling away from device housing. 11. Confirm which back activating bracket you have and follow below guide. 3/4 Cut down Cut Good!
6 12. Remove bottom pin from back activating bracket. 13. Remove back activating bracket from connecting rod. 14. Remove spring and spring cap. 15. Discard old spring and replace with new spring. 16. Line up acme bracket with the pin on the connecting rod. Mark on the connecting rod where the acme bracket stops. For Doromatic & PD10/11 s (old) retrofits 17. Cut connecting rod at your mark.
7 Re-insert connecting rod into activating bracket 18. with new spring installed. 19. Before re-installing attaching bracket make sure magnet side of the bracket is on the same side as the sensor. 20. Re-insert pin into activating bracket thru connecting rod, make sure rubber donut is in place. 21. After pin is installed put connecting rod assembly back into exit device housing. Rubber Donut 22. Re-install (2) screws to secure back activating bracket to device housing. 23. Confirm the spring is still at the front of the connecting rod if not re-install. Activating bracket screws
8 24. Re-install pin connecting device head to connecting rod. 25. Re-install (2) screws to secure front activating bracket to device housing. 26. Slide the new motor mount into the exit device housing. 27. Re-install (2) screws to secure front activating bracket to device housing. Rotate Turcite counterclockwise onto the acme thread until the holes on the motor mount line up with the holes on the exit device housing. Turcite Turcite Acme Thread 29. Secure motor mount to device by installing (2) Phillips screws provided. 30. Slide push pad back onto device. Make sure activating brackets are in the correct channel.
9 31. Add program sticker to back of the device. E. Step 1- Setting PTS Select your preferred torque mode (ships in standard torque) Press the device push pad to the desired setting. (Recommend to fully depress and release 5%, giving the device room for changing door conditions.) Step 2- While depressing the push pad, apply power. (i.e. presenting the credential to the reader). Step 3- Continue to keep pad depressed, the device will beep 6 times. After the beeps have stopped, release the pad and now the adjustment is complete. If not to your liking repeat the three steps. on on mm4s switches LOW TORQUE on STANDARD TORQUE on HIGH TORQUE PTS PROGRAMMING LOCKED
LLP-UL-M-KIT Series Motorized Electric Latch Retraction
LLP-UL-M-KIT I n s ta l l at I o n InstructIons The LLP-UL-M-KIT is a field installable motorized latch pullback kit for the Hager 4500 and Lawrence 8000 series. B. C. A. D. LLP-UL-M-KIT IncLU d e s A.
More informationslp-ul-m KIT INSERT Instructions A. B. C. E. F. G.
slp-ul-m KIT INSERT Instructis The Command Access SLP-UL-M-KIT is a field installable motorized latch-pullback kit for the Sargent 80 series. A. B. C. D. E. E. F. G. A. B. C. D. E. F. Kit Includes 1- Motor
More informationPD10-M-RIM INSTALLATION INSTRUCTIONS. The PD10-M-RIM is a storefront grade 1 exit device equipped with motor drive latch retraction.
PD10-M-RIM INSTALLATION INSTRUCTIONS The PD10-M-RIM is a storefront grade 1 exit device equipped with motor drive latch retraction. Retrofits Doromatic 1790 & First Choice 3790. B. G. A. C. D. E. F. PD10-M-RIM
More informationPD15-UL-M KIT INSTRUCTIONS
PD5-UL-M KIT INSTRUCTIONS The Command Access PD5-UL-M-KIT is a field-installable motorized latchpullback kit for the Jackson 85/95 & AHT 8/9 series devices. A. B. C. D. E. F. G. H. I. KIT INCLUDES TOOLS
More informationVLP-UL-M-KIT INSTALLATION INSTRUCTIONS
VLP-UL-M-KIT INSTALLATION INSTRUCTIONS The Command Access VLP-UL-M-KIT is a field-installable motorized latch-pullback kit for the Von Duprin 33/35 & 98/99 series devices. F. G. i. H. j. K. D. Kit Includes
More informationPD10-M-CVR INSTALLATION INSTRUCTIONS. Tools Required. PD10-M-CVR Includes
PD10-M-CVR INSTALLATION INSTRUCTIONS The PD10-M-CVR is a storefront grade 1 exit device equipped with motor drive latch retraction. Retrofits Doromatic 1690 & First Choice 3690. C. I. D. E. F. G. H. PD10-M-CVR
More informationVLP-UL-KIT INSTALLATION INSTRUCTIONS. The VLP-UL-KIT for 36 or 48 is a field installable solenoid latch pullback for the Von Duprin 33/35 &
Solenoid VLP-UL-KIT INSTALLATION INSTRUCTIONS The VLP-UL-KIT for 36 or 48 is a field installable solenoid latch pullback for the Von Duprin 33/35 & 98/99 series exit devices..050 Hex Wrench retraction
More informationPD18-RIM INSTALLATION INSTRUCTIONS
PD18-RIM INSTALLATION INSTRUCTIONS The PD18-RIM is a storefront grade 1 exit device equipped with motor driven latch retraction. Retrofits Adams Rite 8800 series. A. C. E. B. D. PD18-RIM Includes A. RIM
More informationII E INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT
II E1500-11 INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT KITS ARE UL LISTED UNDER CATEGORY GWVW, GWVW7 (CANADA) (ACCESSORY FOR USE ON FIRE EXIT HARDWARE AND PANIC HARDWARE). INDEX
More informationINSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT
INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT INDEX FUNCTION DESCRIPTION PAGE 1 PARTS LIST PAGE 2 TOOLS REQUIRED PAGE 2 KIT INSTALLATION INSTRUCTIONS PAGE 2-10 KIT ADJUSTMENT INSTRUCTIONS
More information* * E996L Series. E996L for Rim/Vertical. E996L for Mortise CAUTION
*921297-00* 921297-00 Electric Locking Trim E996L Series Installation Instructions CAUTION Product is shipped in Fail Safe (FS) configuration. Fail Safe configuration is required by code in some applications
More informationAlliance Towel Dispensing System. Operation Manual
Alliance Towel Dispensing System Operation Manual Alliance Towel Dispensing System Table of Contents Safety Information... page 2 Mounting Instructions... page 3 Towel Loading Instructions... page 7 Settings...
More information55 Series Exit devices
55 Series Exit devices The Von Duprin 55 Series is a range of push bar exit devices designed to suit single and double door applications with narrow stiles. The 55 Series can be used on aluminium hollow
More informationModel 2300JL Installation Guide
Model 2300JL Installation Guide POWER ACCESS CORPORATION 4 HERSHEY DRIVE, DOCK 4 ANSONIA, CT 06401 800-344-0088 WEBSITE: www.power-access.com EMAIL: salesinfo@power-access.com 1 STANDARD PARTS MODEL 2300JL
More informationModel 2300DL Installation Guide
Model 2300DL Installation Guide POWER ACCESS CORPORATION 4 HERSHEY DRIVE, DOCK 4 ANSONIA, CT 06401 800-344-0088 WEBSITE: www.power-access.com EMAIL: salesinfo@power-access.com 1 STANDARD PARTS MODEL 2300DL
More information4500 Series Electric Exit Devices Request to Exit (RX) Installation Instruction Grade 1 I-ED00368
4500 Series Electric Exit Devices Request to Exit (RX) Installation Instruction Grade 1 I-ED00368 DEVICES COVERED IN THESE INSTRUCTIONS: RX Request to Exit ELECTRICAL SPECIFICATIONS Note: SPDT mechanical
More informationProduct Guide. If it has wires think... Command Access!
Product Guide 41 If it has wires think... Command Access! ABOUT US Our goal is to serve the customer to the best of our ability every time! Command Access is a manufacturer and modifier of high quality
More information1 of 6. Installation Instructions. ED3200/ED3200A Series Rim Exit Device ASSA ABLOY. Plug FM362 (05/15) Inactive Case. Chassis. Inactive Case.
Installation Instructions ED3200/ED3200A Series Rim Exit Device In U.S.: Corbin Russwin, Inc. 225 Episcopal Road Berlin, CT 06037 USA www.corbinrusswin.com In Canada: Door Security Solutions Canada 160
More informationElectrical Options Booklet. Table of Contents
*24228413* 24228413 Electrical Options Booklet Table of Contents EL Wiring... EL Troubleshooting... SD/EL 98/99 Cylinder Dogging... SS Wiring... 330, 350, RX-330 and RX-350 Push Bar Trim Mechanical Installation...
More informationTOYOTA CAMRY HANDS FREE BLU LOGIC Preparation
TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationTOYOTA TUNDRA HANDS FREE BLU LOGIC Preparation
TOYOTA TUNDRA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationCONTROLLER DIAGNOSTIC GUIDE
Proprietary tice: This document contains proprietary information which not to be reproduced, transferred, to other documents, disclosed to others, used for manufacturing or any other purpose without the
More informationTOYOTA VENZA HANDS FREE BLU LOGIC Preparation
TOYOTA VENZA 2009- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationSpectra Class. N6000 Series Exit Devices SECURITY DOOR CONTROLS. N6100 Rim Mount Exit Device. N6200 Surface Vertical Rod Exit Device.
N6000 Series Exit Devices Spectra Class Rim Mount Surface Vertical Rod N6100 Rim Mount Exit Device For use on single doors or pair of doors with mullion 1-3/4"(44 mm) door thickness standard. Specify thickness
More informationTRITON ERROR CODES ERROR CODE MODEL SERIES DESCRIPTION RESOLUTION
0 8100, 9100, 9600, 9610, 9615, 9640, No errors 9650, 9700, 9710, 9705, 9750, RL5000 (SDD),RL5000 (TDM), RT2000, 9800, MAKO, SuperScrip 1 9615 Unsolicited note channel 1 2 9615 Unsolicited note channel
More informationConflicts: JBL Audio, Factory Navigation, Accessory XM Satellite Radio, and Accessory Sirius Satellite Radio
TOYOTA YARIS SEDAN 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts: JBL Audio, Factory Navigation,
More informationSmartLock Accessories
CANSEC ACCESSORIES SmartLock Accessories CA SLbox CA SLBOX SmartLock enclosure 9.5 x 13 x 3 metal enclosure with room for 1 or 2 SmartLock controllers, Cansec power supply and 12V 7 AH battery C Ca ps123a
More informationSCION XB HANDS FREE BLU LOGIC Preparation
SCION XB 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationDual Roller Fascia Coupled FlexShades Assembly and Installation Instructions
Dual Roller Fascia Coupled FlexShades Assembly and Installation Instructions 1 Upon receiving your Coupled FlexShades, open and inspect to make sure you have received the proper sizes, fabrics, and mounting
More informationCP2000 Ballast - Replacing Thyristor Instruction Sheet
CP2000 Ballast - Replacing Thyristor Instruction Sheet INTRODUCTION These instructions are for the CP2000 Ballast and explain how to: replace the existing 80 Amp Thyristor with a new 100 Amp Thyristor
More informationSpectra Class - Specification Grade Exit Devices for superior Architectural Style & Performance
S6000 & N6000 Spectra Exit Devices Spectra Class - Specification Grade Exit Devices for superior Architectural Style & Performance The new mechanical SDC S6000 & N6000 Spectra series panic and fire rated
More informationAdams rite. Exit Devices & parts exit devices series exit device parts
Adams rite Exit Devices & parts exit devices 8099 8211 8099 Active Dummy Bar with Switch Can be wired normally open or normally closed to operate maglock, alarm, etc No latching mechanism 8211 Surface
More informationTOYOTA TUNDRA TVIP V4 Preparation
Preparation Part Number: PT398-00100 PT398-00100-AA Conflicts Do not install into vehicles without RKE system. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM
More informationINSTALLATION INSTRUCTIONS CRL JACKSON 2085E
INSTALLATION INSTRUCTIONS CRL JACKSON 2085E ELECTRIC LATCH RETRACTION CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com
More informationInteli-Lift GEN II DUMBWAITER
1 877-345-4387 530-295-4900 www.eilifts.com Inteli-Lift GEN II DUMBWAITER The Easiest Dumbwaiter system on the Market Fully UL Certified Dumbwaiter Systems UL File # SA32120 This manual will cover the
More informationSCION TC HANDS FREE BLU LOGIC Preparation
SCION TC 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00099 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationSolar & Roller Shades
STEP BY STEP INSTALLATION INSTRUCTIONS Solar & Roller Shades Loop Control, Loop Control with Cassette/2 on 1 Headrail & Loop Control with Metal Valance Table of Contents Step 1 - Getting Started....3 Everything
More informationKAWNEER 1686 EL CONCEALED EXIT DEVICE
FEBRUARY, 2012 1 ROD AND CENTER CASE ASSEMBLY: 1) For inactive doors or doors without exterior cylinder, or doors without the need for exterior cylinder dogging, the removal of the cylinder dogging pawl
More informationTOYOTA TACOMA HANDS FREE BLU LOGIC Preparation. Item 5 Item 6 Item 7 Item 8. Item 4. General Applicability Note: Recommended Tools
TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00098 Conflicts: JBL Audio, Factory Navigation Kit Contents: NOTE: Part number of this accessory may not be the same as the part number
More informationDESIGNED BY EXPERIENCE PLASTIC SPHERE DISPENSER USER MANUAL. Manufactured by PSDS, Inc. for sole distribution by:
DESIGNED BY EXPERIENCE PLASTIC SPHERE DISPENSER USER MANUAL Manufactured by PSDS, Inc. for sole distribution by: AEROSTAT, INC. 8830 AIRPORT BLVD LEESBURG, FL 34788 WEBSITE: AEROSTATINC.COM TEL: 352 787-1348
More informationService Manual ISO7000R Recumbent Bike
Service Manual ISO7000R Recumbent Bike Before Using this product, read this manual and follow all safety rules and operating instructions. Maintenance The ISO7000R is virtually maintenance free. After
More informationTrilogy Double-Sided DL5200, DL5300 & PDL5300 Installation Instructions
345 Bayview Avenue Amityville, New York 11701 For Sales and Repairs 1-800-ALA-LOCK For Technical Service 1-800-645-9440 Publicly traded on NASDAQ Symbol: NSSC ALARM LOCK 2008 Trilogy Double-Sided DL5200,
More information2904 Power Supply Installation Instructions I-EA00041
FEATURES Controls an opening with electrified locking device and automatic door operator Separate inputs for activation switch on entry and exit sides of opening Separate 24 VDC outputs for fail safe and
More informationPlease forward any questions or comments regarding this Troubleshooting Guide to
2009 Human Touch, LLC. All rights reserved. May 28, 2009 Please forward any questions or comments regarding this Troubleshooting Guide to documentation@humantouch.com. HT-1650 Troubleshooting This Troubleshooting
More informationTOYOTA tc HANDS FREE BLU LOGIC Preparation
TOYOTA tc 2011- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationSCION XB HANDS FREE BLU LOGIC Preparation. Item 4 Item 5 Item 6 Item 7. General Applicability. Note: Recommended Tools
SCION XB 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00090 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: Item 1 Item 2 Item
More informationMotorized Electric Latch Retraction
; SECTION I: OVERVIEW 1. Description The Corbin Russwin MELR Electric Latch Retraction (ELR), refer to Figure 1, works with ED4000 & ED5000 Series exit devices to provide remote-controlled latch retraction
More informationAuto-Level Troubleshooting (Old Platform) Electronic Control- Prior to 2009, Pressure Switch Control panel #s 2057, 2058, 2795, 2795B
Auto-Level Troubleshooting (Old Platform) Electronic Control- Prior to 2009, Pressure Switch Control panel #s 2057, 2058, 2795, 2795B This guide addresses the troubleshooting of electronic controls used
More informationSUNROOF - SERVICE INFORMATION ADJUSTMENTS
SUNROOF - SERVICE INFORMATION DESCRIPTION OPERATION DIAGNOSIS AND TESTING POWER TOP - SUNROOF SUNROOF ASSEMBLY-MODULE REMOVAL INSTALLATION CHANNEL-DRAIN REMOVAL INSTALLATION COVER-GUIDE MECHANISM REMOVAL
More informationST-100 DATA WIZARD USER MANUAL
ST-100 DATA WIZARD USER MANUAL Full color manual can be downloaded at www.bellatrix.com 08/10/05 Contents Page SUPER WAND OVERVIEW 2 BUFFER BOX 3 ST-100 INSTALLATION 4 SETTING UP AND INITIALIZING 6 ERROR
More informationINSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks
Securitron Magnalock Corp. Tel 775.355.5625 550 Vista Boulevard Fax 775.355.5633 Sparks, NV 89434 info@securitron.com www.securitron.com ASSA ABLOY, the global leader in door opening solutions INSTALLATION
More informationINSTALLATION GUIDE Car Show Dual DVD Headrest Replacement System
INSTALLATION GUIDE Car Show Dual DVD Headrest Replacement System NOTICE OF INTENDED INSTALLATION AND USE CAR SHOW VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER, AND ARE TO BE INSTALLED ONLY
More informationPRICE LIST. Table of Contents
PRICE LIST Table of Contents 3600 Concealed Vertical Rod... 2-3 3700 Rim Latching... 3-4 Electrical Latching Kits... 4 Power Supplies... 4 Power Transfers... 4 Exit Device Accessories... 5 Inactive Devices...
More informationSUBJECT: Front Door Window Glass - Loose, Sticks, Binds, or Express-Up Reversal
NUMBER: 23-032-07 GROUP: Body DATE: August 2, 2007 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
More information*ININST.1002* 1690 Touchbar. Index:
*ININST.1002* ININST.1002 Concealed Vertical Rod Panic Device 1690 Touchbar Installation Instructions Index: : The door prep for the 1690 Hex Bottom Rod is different than for the RL bottom rod. Please
More informationCenterLine Filter Wheel
Engineering Excellence Because Your Image Depends On It User s Guide CenterLine Filter Wheel Finger Lakes Instrumentation, LLC September 2014 WELCOME Thank you for purchasing an FLI CenterLine Filter Wheel.
More informationGeneral Applicability Note: Recommended Tools. Personal & Vehicle Protection Safety Goggles Seat Covers Floor Covers Special Tools. Installation Tools
TOYOTA HIGHLANDER/HIGHLANDER HV 2008- Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationSolar & Roller Shades
STEP BY STEP INSTALLATION INSTRUCTIONS Solar & Roller Shades 1 2 3 4 5 Motivia Motorization Table of Contents Step 1 - Getting Started....3 Everything You Need A Smooth Set-Up We want you to love your
More informationINSTALLATION MANUAL. Power-Pole Blade Edition Shallow Water Anchor. Installation Instructions
INSTALLATION MANUAL Power-Pole Blade Edition Shallow Water Anchor Installation Instructions CAUTION: Read this instruction manual carefully. Become familiar with the controls and know how to operate the
More informationIL500 Sierra Inclined Platform Lift
IL500 Sierra Inclined Platform Lift Installation & Service Manual www.harmar.com 800-833-0478 IMPORTANT: Read and understand this manual thoroughly before attempting to install or operate the lift. If
More informationValidator and Control Board Update Instructions for BC1
Validator and Control Board Update Instructions for BC1 Installation Overview The update kit for the Rowe BC1 enables the changer to interface with a Mars AE/VN 120-volt validator. The validator determines
More informationInstallation Manual. AutoSteer. Gleaner Combine. AutoGuide 2 Steer Ready. Supported Models A66 A76 R66 R76 S67 S77 PN: A
Installation Manual AutoSteer Gleaner Combine AutoGuide 2 Steer Ready Supported Models A66 A76 R66 R76 S67 S77 PN: 602-0312-01-A LEGAL DISCLAIMER Note: Read and follow ALL Instructions in this manual carefully
More information56- Electric Latch Retraction Exit Devices Installation and Wiring Instructions
SECTION I: OVERVIEW 1. Description The Sargent 56- prefix ELR works with 80 Series exit devices to provide remote-controlled latch retraction. It is compatible with the following prefixes: 53 - Latchbolt
More informationNOTE. Installation and Service Manual Dual Planetary Gearmotor Slim Rack Slide Out System
Installation & Service Manual Slim Rack In-Wall Slide Out System Control Box Part Number 1510000199 Content Copyright LCI/Power Gear Issued: December 2014 #3010002588, Rev. 0E Installation and Service
More informationService Manual Gulf Stream Electronic Full Wall Slide Systems
Service Manual Gulf Stream Electronic Full Wall Slide Systems CONTENTS Page Before you operate the slide system 2 Operating Instructions 3 Preventive maintenance 3 Manually overriding your slide system
More informationInstallation Instructions
Installation Instructions MX3635-01 Rev. E Models HydraSwing 40s HydraSwing 40F 4,000 lb (1,814 kg) 10-15 seconds HydraSwing 40 4,000 lb (1,814 kg) 15-20 seconds HydraSwing 40 Twin 4,000 lb (1,814 kg)/leaf
More informationONE TOUCH CONTROL BOX
ONE TOUCH CONTROL BOX CONVERSION KIT INSTRUCTIONS REMOVAL, INSTALLATION, OPERATION, AND REMOTE CONTROL PROGRAMMING THUNDERSTONE PART #101322 REVISION A JULY 14 TH 2016 2 P a g e INSTALLING THE THUNDER
More informationGPS Steering System Installation Manual
GPS Steering System Installation Manual Supported Vehicles Challenger Massey Ferguson AGCO MT-645C, MT-645D MF-8650 DT-205B MT-655C, MT-655D MF-8660 DT-225B MT-665C, MT-665D MF-8670 DT-250B MT-675C, MT-675D
More information9.2, 9.2s, 9.20, 9.20s Treadmill
9.2, 9.2s, 9.20, 9.20s Treadmill Warning: This service manual is for use by Precor trained service providers only. If you are not a Precor Trained Servicer, you must not attempt to service any Precor Product;
More informationApplicable to the Following Part Numbers. Notes and Maintenance. Torque Specifications. Metric SAE. Use above torque setting unless otherwise noted
INSTALLATION MANUAL Level of Difficulty Moderate This is the second first of two of two manuals required to complete this installation. The first second manual manual is is included with with your mounting
More informationINSTALLATION GUIDE AV7900 Dual Multimedia Headrest Replacement System
INSTALLATION GUIDE AV7900 Dual Multimedia Headrest Replacement System NOTICE OF INTENDED INSTALLATION AND USE AV7900 VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER, AND ARE TO BE INSTALLED ONLY
More informationKWIKEE DOOR SWITCH STEP ACTIVATION INSTALLATION GUIDE ( )
Purpose Note: Information for this document has been obtained from Kwikee Products document number 1421330, Revision 0B, dated February 2008 and updated for current practices. This document explains the
More informationConflicts: Vehicles with a sunroof
Toyota 4Runner Non/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit -00110-15, Beige 00016-00120; Fit Kit -00120-15, Gray Accessory Code: ED6 Conflicts: Vehicles with a sunroof Kit Contents:
More informationTOYOTA PRIUS 2010 TVIP V4 PREPARATION
PREPARATION Part #: PT398-47091 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.
More informationARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI
II 1400-6 ARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI ACSI 1426-04-AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1092, REV. C INSTALLATION For C-UL Listed applications,
More informationS6100 SERIES REVERSIBLE PANIC/FIRE EXIT RIM DEVICES INSTALLATION INSTRUCTIONS
801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622 www.sdcsecurity.com E-mail: service@sdcsecurity.com S6100 SERIES REVERSIBLE PANIC/FIRE EXIT RIM DEVICES INSTALLATION INSTRUCTIONS These instructions
More informationAutomatic Roof Hatch Opener
Automatic Roof Hatch Opener Installation Guide REQUIRED TOOLS (These tools are required to complete the installation) Cordless Drill 1/8 1/4 Drill Bits 1/8 Pin Punch #2 Philips Bit Rachet Sharpie Hammer
More informationMotivia Motorization
STEP BY STEP INSTALLATION INSTRUCTIONS Luxe Linen Honeycomb Shades Skylight 1 2 3 4 5 Motivia Motorization Everything You Need Table of Contents Step 1 - Getting Started....3 Overview - Motorized Honeycomb
More informationInstallation Instructions
Approx. Install Time 3Hrs 00Min Installation Instructions Vehicle Application Year: 2013-2017 Make: Ram Model: 2500/3500 Diesel Engine: 6.7L Cummins Tools Required 7mm, 8mm, 10mm,& 13mm Wrench & Socket
More informationToyota 4RUNNER With/MR Overhead Video
Toyota 4RUNNER With/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit-00110-14, Beige 00016-00120; Fit Kit-00120-14, Gray Accessory Code: ED7 Conflicts: Vehicles without a sunroof Kit Contents:
More informationLEXITM. Retrofit Control Trim For Exit Devices The Universal Access Control Solution For Electrifying Exit Devices
You Want, We Do 1 LEXITM Retrofit Control Trim For Exit Devices The Universal Access Control Solution For Electrifying Exit Devices Easy Installation To Existing Doors Does not require cutting into frame
More informationMcDonalds Installation Guide
McDonalds Installation Guide Canopy COD Installation CCOD ------------------------------------------------------------------------------------------------------ Metal Pedestal COD Installation MCOD Everbrite
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles Case IH Vehicles Case 2577 Combines Case 2588 Combines Accuguide Ready PN: 602-0233-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions
More informationSIGNETMARINE. Livewell Bait Pump Alarm. No Dead Bait.
B A I T WAT C H SIGNETMARINE Livewell Bait Pump Alarm No Dead Bait. The SIGNETMARINE BaitWatch System alerts you to a livewell pump problem before your fishing trip turns into one. The loud alarm and dual-color
More informationFOR SIT-STAND WORKSTATION
INSTALLATION MANUAL FOR SIT-STAND WORKSTATION Weight Capacity: 6.5-24.5 lbs. 6017180 Rev. B Contents Tools Required / Supplied Part Kits / Warnings/Disclaimers...2 Base Installation Clamp Mount Base Location...3
More informationALL700/ALL700-CM INSTALLATION INSTRUCTIONS
ALL700/ALL700-CM INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power
More information8800 Rim Exit Device 80 Series
8800 Rim Exit Device 8800 Series Rim Exit Device 8800 Features Designed for standard width stile applications on wood and metal doors Also available as an HC8800 or WS8800 for hurricane-resistant applications,
More informationM: Fuel System M: Introduction
Page 1 of 7 2011 PCED 6.7L Diesel SECTION 5: Pinpoint Tests Procedure revision date: 12/14/2010 M: Fuel System M: Introduction M1 CHECK FOR DIAGNOSTIC TROUBLE CODES (DTCS) te: Repair any fuel injector
More informationTOYOTA PRIUS 2004 TVIP V2 (GBS ADD ON) Section I Installation Preparation
Section I Installation Preparation Part Number: 08586 47840 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 3 1 ECU Mounting Bracket Hardware Bag
More informationAUTO GLIDE INSTALLATION GUIDE MANUAL A
GLIDE INSTALLATION GUIDE MANUAL A TABLE OF CONTENTS.0 PRODUCT OVERVIEW 3-4. System Requirements 4.0 GLIDE MECHANICAL INSTALLATION 5-6. Auto Glide Key Pad Installation. Replacing Existing 3 LED Indicator
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY A20 5TH WHEEL HITCH TABLE OF CONTENTS Page# Description 1 Warnings & Precautions 2 - Assembly & Installation
More informationPackage Contents. Mounting Hardware
Securitron Magnalock Corp. www.securitron.com Tel 800.624.5625 techsupport@securitron.com M680BDCX MAGNALOCK SERIES Installation Instructions Table of Contents Specifications 2 Configuring Options 3 Installation
More informationSection 55 Chapter 6
Section 55 Chapter 6 REMOTE HYDRAULICS CONTROLLER Calibration and Fault Codes 6-12880NH TABLE OF CONTENTS REMOTE HYDRAULICS CONTROLLER CALIBRATION... 55-5 Requirements For Calibration... 55-5 Aux Set Main
More informationigen2500 and ipro2500 IGNITION COIL RETROFIT GUIDE
igen2500 and ipro2500 IGNITION COIL RETROFIT GUIDE This comprehensive retrofit guide is for replacing the ignition coil on Westinghouse s igen2500 and ipro2500 inverter generators. The purpose of this
More informationHoneycomb Shades Skylight
STEP BY STEP INSTALLATION INSTRUCTIONS Honeycomb Shades Skylight 1 2 3 4 5 Motivia Motorization Everything You Need A Smooth Set-Up We want you to love your new window coverings and that includes having
More information8800 Rim Exit Device 80 Series
8800 Rim Exit Device 8800 Series Rim Exit Device 8800 Features Designed for standard width stile applications on wood and metal doors Also available as an HC8800 or WS8800 for hurricane-resistant applications,
More informationModel: PSB100. Rear Parking Sensor System. Installation Manual TABLE OF CONTENTS
Rear Parking Sensor System Model: PSB100 Installation Manual TABLE OF CONTENTS Warnings...2 Product Description...3 Packing List...3 Installation Instructions...4 Mounting the Sensors...4 Installing the
More informationAutoFaucet. with Surround Sensor Technology. Installation & Maintenance
AutoFaucet with urround ensor Technology Installation & Maintenance Instalaion y Mantenimiento Installation Et Maintenance on www.technicalconcepts.com or call 800-551-5155 Looks Clean - Is Clean. AutoFaucet
More informationSUSPENSION MODULE by
SUSPENSION MODULE by Dear Customer, thank you for choosing Land Rover Passion and for purchasing the suspension module Easy Lift. This product has been designed and manufactured respecting the highest
More informationCHAPTER 5 CORDLESS GENERAL CORDLESS COMPONENTS
CHAPTER 5 CORDLESS CHAPTER 5 CORDLESS GENERAL The Cordless aligner offers the users the capability to perform all alignment functions without the use of cables leading from the wheel sensors to the console.
More information