INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS"

Randell Greene
6 years ago
Views:

1 INSTALLATION INSTRUCTIONS Accessory Application Publications No. KIT P/N 08E49-S9V PILOT LX AII Issue Date MAY 2002 PARTS LIST Illustration of the Security System installed on the Vehicle Hood switch harness Hood switch 18 Wire ties INSTALLATION Ground bolt Offset wire tie Wire tie with holder Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2. Disconnect the negative cable from the battery. TOOLS AND SUPPLIES REQUIRED Flat-tip screwdriver 10 mm Combination wrench Ratchet 10 mm Socket Diagonal cutters Felt-tip pen 10 mm Box-end wrench 2002 American Honda Motor Co., Inc - All Rights Reserved. AII (0205) 08E49-S9V of 8

2 3. Open the hood, and remove the bulkhead cover (11 short clips). BULKHEAD COVER SHORT CLIPS (11) 5. Using the felt-tip pen, mark the bulkhead center stay at three locations where the hood lock bracket is positioned. LOCK BRACKET FRONT MARKS (3) FELT-TIP PEN 4. Lift the radiator reservoir up, and move it out of the way. BULKHEAD CENTER STAY 6. Unscrew the three bolts that secure the hood lock, then remove the hood opener cable from the hood lock. LOCK RADIATOR RESERVOIR OPENER CABLE BOLT LOCK 2 of 8 AII (0205) 2002 American Honda Motor Co., Inc - All Rights Reserved.

3 7. Connect the hood opener cable to the hood switch, and position the hood switch on the bulkhead center stay by aligning the holes in the switch with the marks made in step 5. Temporarily install the three bolts. Shut the hood, and check that the alignment of the new hood switch and the hood latch is correct, and check that the hood is latched securely. When you re satisfied with the results, open the hood, and tighten the hood latch bolts securely. MARKS (3) 9. Using a utility knife, make a crosscut in the rubber mat as indicated by the slits so that the grommet concealed under the mat is exposed. Lift the rubber mat and remove the grommet from the lower dashboard, then route the 2-pin connector of the hood switch harness into the cabin. Seat the grommet on the hood switch harness in the hole in the lower dashboard properly. RUBBER MAT (Be extremely careful not to damage the lower dashboard and adjacent wire harnesses) GROMMET (Discard.) GROMMET ON (Seat the grommet in the hole in the lower dashboard properly) BULKHEAD CENTER STAY SLIT OUTSIDE CABIN OPENER CABLE (Be sure to connect the cable to the hood switch) BOLT (Reuse.) LOWER DASHBOARD 8. Connect the 2-pin connector of the hood switch harness to the 2-pin connector of the hood switch, then route the hood switch harness to the grommet on the lower dashboard along the vehicle harness. 2-PIN LOWER DASHBOARD GROMMET 2-PIN 2-PIN 2002 American Honda Motor Co., Inc - All Rights Reserved. AII (0205) 3 of 8

4 10. Remove and discard the bolt that secures the relay box bracket to the vehicle body, and secure the ground terminal of the hood switch harness with the ground bolt from the kit. Do not use the existing SRS ground for the hood switch. 12. Secure the hood switch harness to the vehicle harness with three wire ties in the areas shown. BOLT (Discard.) GROUND BOLT (From the kit.) (Do not use the SRS ground for the hood switch.) GROUND TERMINAL RELAY BOX BRACKET 11. Secure the hood switch harness to the vehicle harness with three wire ties in the areas shown. 13. Secure the hood switch harness to the vehicle harness with two wire ties. GROMMET WIRE TIE (Attach the wire tie under the hood switch grommet.) 4 of 8 AII (0205) 2002 American Honda Motor Co., Inc - All Rights Reserved.

5 14. Secure the hood switch harness to the vehicle harness with two wire ties. If fog lights are installed, route the hood switch harness and fog light harness together. 16. Remove the driver s dashboard lower cover (one self-tapping screw, three clips, and two hooks). HOOK DRIVER S DASHBOARD LOWER COVER SELF-TAPPING SCREW CLIPS (3) 15. Attach the wire tie with holder to the 2-pin connector of the hood switch, then secure the 2-pin connector to the vehicle harness with this wire tie with holder. 17. Remove the driver s side trim from the center console (seven clips and one hook). CENTER CONSOLE WITH HOLDER HOOK DRIVER S SIDE TRIM CLIPS (7) 18. Remove the passenger s side trim in the same manner. 2-PIN 2002 American Honda Motor Co., Inc - All Rights Reserved. AII (0205) 5 of 8

6 19. Route the hood switch harness along the vehicle harness behind the glove box frame, and toward the driver s side of the vehicle. Continue routing the harness between the center console and the air conditioner duct. 20. On the left side of the steering shaft, locate the 2- pin connector blue-taped to the security system harness. Remove the blue tape to free the connector. Remove and discard the dummy connector from the 2-pin connector you just freed. GLOVE BOX FRAME S SECURITY SYSTEM 2-PIN CENTER CONSOLE AIR CONDITIONER DUCT BLUE TAPE (Remove.) SECURITY SYSTEM 2-PIN DUMMY (Discard.) UNIT STEERING SHAFT 21. Continue routing the hood switch harness 2-pin connector above the steering shaft, and connect it to the security system harness 2-pin connector. 6 of 8 AII (0205) 2002 American Honda Motor Co., Inc - All Rights Reserved.

7 22. Attach the offset wire tie to the hood switch harness at the green tape, and push the clip into the hole in the steering hanger beam bracket. 25. Near the center dashboard area, secure the hood switch harness to the vehicle harness with one wire tie. STEERING HANGER BEAM BRACKET OFFSET GREEN TAPE 2-PIN 23. Secure the hood switch harness 2-pin connector to the vehicle harness with one wire tie. 24. Secure the hood switch harness to the vehicle harness with three additional wire ties in the areas shown. 26. Remove the stoppers from both sides of the glove box, and lower the glove box. Secure the hood switch harness to the glove box frame with one wire tie. GLOVE BOX FRAME GLOVE BOX STOPPERS 27. Reinstall the glove box American Honda Motor Co., Inc - All Rights Reserved. AII (0205) 7 of 8

8 28. On the passenger s side of the vehicle, secure the hood switch harness to the vehicle harness with two wire ties in the areas shown. 29. Check that all wire harnesses are routed properly and all connectors are plugged in. 30. Reconnect the negative cable to the battery. 31. Enter the customer s radio anti-theft code, and reset the radio station presets. 32. Set the clock. 33. Arm the security system, then open the hood to make sure the alarm sounds. 34. Reinstall the driver s dashboard lower cover, the driver s and passenger s side trim, and the bulkhead cover. NOTE: Whenever the battery is disconnected, the driver s window AUTO function is disabled. 35. Start the engine. Push down on the driver s window switch until the window is fully open. 36. Pull up on the driver s window switch to close the window completely, then hold the switch for 2 seconds. 37. Lower and raise the driver s window to check operation of the driver s window AUTO function. 8 of 8 AII (0205) 2002 American Honda Motor Co., Inc - All Rights Reserved.

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publications No. SECURITY SYSTEM P/N 08E49-SDA-100 ACCORD 2- AND 4-DOOR AII 30666 Issue Date AUG 2005 PARTS LIST Hood switch harness Illustration of the