slp-ul-m KIT INSERT Instructions A. B. C. E. F. G.
|
|
- Ira Ward
- 5 years ago
- Views:
Transcription
1 slp-ul-m KIT INSERT Instructis The Command Access SLP-UL-M-KIT is a field installable motorized latch-pullback kit for the Sargent 80 series. A. B. C. D. E. E. F. G. A. B. C. D. E. F. Kit Includes 1- Motor Mount w/ MM4S series module 2-8/32 X 1/4 Phillips head screws 1-8 Lead w/ VD Cnector 1- Push & go cnector 1- MM4S switch program sticker 1- Dogging Hole Cap Tools Required Cordless Drill Hammer & Pin Punch(recommend) or 3/16 drill bit 5/16 Nut driver (recommended) or Flat head screwdriver #2 Phillips head screwdriver Install Video Command Access Technologies La Palma Ave, Yorba Linda, CA Phe:(888) #20094_I
2 Technical Informati MM4S Video mm4s switches LOW TORQUE STANDARD TORQUE HIGH TORQUE PTS PROGRAMMING LOCKED SPECIFICATIONS Input Voltage: 24VDC +/- 10% Wire gauge: Minimum 18 gauge Direct wire run - no relays or access ctrol units in-between power supply & module Low Torque Mode Average Latch Retracti Current: 600 ma Average Holding Current: 150 ma Standard Torque Mode Average Latch Retracti Current: 900ma Average Holding Current: 215 ma High Torque Mode Average Latch Retracti Current: 2 Amp Average Holding Current: 250 ma Setting PTS **Important Info** Make sure to set PTS before finishing installati Step 1- Select your preferred torque mode (ships in standard torque) Press the device push pad to the desired setting. (Recommend to fully depress and release 5%, giving the device room for changing door cditis.) Step 2- While depressing the push pad, apply power. (i.e. presenting the credential to the reader). Step 3-2 Beeps Ctinue to keep pad depressed, the device will beep 6 times. After the beeps have stopped, release the pad and now the adjustment is complete. If not to your liking repeat the 3 steps. Beeps Explanati Soluti Over Voltage Troubleshooting & Diagnostics > 30V unit will shut down. Check voltage & adjust to 24 V. 3 Beeps Under Voltage < 20V unit will shut down. Check voltage & adjust to 24 V. 4 Beeps Failed Sensor Verify all 3 sensor wires are installed correctly. Replace sensor if problem persists by ctacting ice. 5 Beeps 6 Beeps Retracti or dogging failure PUSH TO SET After 1st fail: 5 beeps then immediately attempts to retract again. After 2nd fail: 5 beeps with pause in-between for 30 secds then device attempts to retract again. After 3rd fail: 5 beeps every 7 minutes, device will not attempt to retract. To Reset: Depress bar for 5 secds at any time. Device is recording it s new positi and power mode after the 6th beep.
3 Electrified Exit Device Installati Example CAT GREEN CHANNEL 1 LED Ceiling Tile NORMALLY OPEN DRY CONTACT FROM ACCESS CONTROL SYSTEM NO VOLTAGE LOCKING HARDWARE + - Module Legend Standard Placement Optial Placement Retrofit 2-pin Cnector The new 2-pin cnector is used when retrofitting a older Command or V Duprin installati so you can plug in to the exisiting cnector. New Exisitng PUSH N GO Cnector STRIPE WIRE 1/8-3/16 7 INSERT INTO WIRE ACCESS HOLES OF CONNECTOR. WIRE ACCESS WIRE RELEASE Recommended Power Supplies: All Command Access exit devices & field installable kits have been thoroughly cycle tested with Command Access power supplies at our factory. For more informati click here or go to our website
4 Installati Instructis 1. Remove End Cap & Filler Plate B. 2. Remove (4) screws from baserail Partially slide push pad approx. 2-3 Using 5/32 drill bit. Open up the (2) back screw holes #3 & Ctinue sliding push pad half way out of the base rail so activating bracket is accessible. Next, remove metal rod and AB mount can be put aside. Activating Bracket Baserail AB Mount Metal Rod
5 CONTINUED 6. Attach the link assembly to the end of the activating bracket. Next, place activating bracket into center of the motor mount. Secure link assembly to activating bracket 7. with Hex wrench provided. Link Assembly 8. Re-install metal rod securing activating bracket to motor mount. 9. Slide push pad with motor kit back into the device. Also, the filler plate must be slid in at same time. Make sure Latch retractor is pressed down so push pad slides over it.
6 CONTINUED Re-install original screws in holes 1 & 2. Install new screws provided in holes 3 & 4. Cnect your VD 8 lead (CAT or VD retrofit) or you can remove the VD cnector to hardwire- take stripped wire end and push into the push & go cnector 12. Next, plug in the push & go cnector into the MM4S. Add Add program sticker to back of the device. program sticker to back of the device. 13. E. Step 1- Setting PTS Select your preferred torque mode (ships in standard torque) Press the device push pad to the desired setting. (Recommend to fully depress and release 5%, giving the device room for changing door cditis.) Step 2- While depressing the push pad, apply power. (i.e. presenting the credential to the reader). Step 3- Ctinue to keep pad depressed, the device will beep 6 times. After the beeps have stopped, release the pad and now the adjustment is complete. If not to your liking repeat the three steps. Step 4- Once you found the correct locati, flip the dip switches to to lock programming. mm4s switches LOW TORQUE STANDARD TORQUE HIGH TORQUE PTS PROGRAMMING LOCKED
PD10-UL-M KIT. I N S E R T I n s t r u c t i o n s A. B. C. D. E. E. E.
PD10-UL-M KIT I N S E R T I n s t r u c t i o n s The PD10-UL-M-KIT is a field installable motorized latch pullback for the PD10/11, Doromatic or Falcon 1690/1790, & First Choice 3600/3700. A. B. C. D.
More informationPD15-UL-M KIT INSTRUCTIONS
PD5-UL-M KIT INSTRUCTIONS The Command Access PD5-UL-M-KIT is a field-installable motorized latchpullback kit for the Jackson 85/95 & AHT 8/9 series devices. A. B. C. D. E. F. G. H. I. KIT INCLUDES TOOLS
More informationLLP-UL-M-KIT Series Motorized Electric Latch Retraction
LLP-UL-M-KIT I n s ta l l at I o n InstructIons The LLP-UL-M-KIT is a field installable motorized latch pullback kit for the Hager 4500 and Lawrence 8000 series. B. C. A. D. LLP-UL-M-KIT IncLU d e s A.
More informationPD10-M-RIM INSTALLATION INSTRUCTIONS. The PD10-M-RIM is a storefront grade 1 exit device equipped with motor drive latch retraction.
PD10-M-RIM INSTALLATION INSTRUCTIONS The PD10-M-RIM is a storefront grade 1 exit device equipped with motor drive latch retraction. Retrofits Doromatic 1790 & First Choice 3790. B. G. A. C. D. E. F. PD10-M-RIM
More informationPD10-M-CVR INSTALLATION INSTRUCTIONS. Tools Required. PD10-M-CVR Includes
PD10-M-CVR INSTALLATION INSTRUCTIONS The PD10-M-CVR is a storefront grade 1 exit device equipped with motor drive latch retraction. Retrofits Doromatic 1690 & First Choice 3690. C. I. D. E. F. G. H. PD10-M-CVR
More informationVLP-UL-M-KIT INSTALLATION INSTRUCTIONS
VLP-UL-M-KIT INSTALLATION INSTRUCTIONS The Command Access VLP-UL-M-KIT is a field-installable motorized latch-pullback kit for the Von Duprin 33/35 & 98/99 series devices. F. G. i. H. j. K. D. Kit Includes
More informationVLP-UL-KIT INSTALLATION INSTRUCTIONS. The VLP-UL-KIT for 36 or 48 is a field installable solenoid latch pullback for the Von Duprin 33/35 &
Solenoid VLP-UL-KIT INSTALLATION INSTRUCTIONS The VLP-UL-KIT for 36 or 48 is a field installable solenoid latch pullback for the Von Duprin 33/35 & 98/99 series exit devices..050 Hex Wrench retraction
More informationPD18-RIM INSTALLATION INSTRUCTIONS
PD18-RIM INSTALLATION INSTRUCTIONS The PD18-RIM is a storefront grade 1 exit device equipped with motor driven latch retraction. Retrofits Adams Rite 8800 series. A. C. E. B. D. PD18-RIM Includes A. RIM
More informationinstall guide OEM-CH(RS)-CH5-[FLRSCH5]-EN
install guide Document number 8 Revision Date 008 firmware OEM-CH(RS)-CH-[FLRSCH] hardware FLRSCH accessories FLPROG (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical
More informationinstall guide DIR-CH(RS)-CH5-[AKX-CH5]-EN
install guide Document number 096 Revision Date firmware DIR-CH(RS)-CH-[AKX-CH] hardware AKX-CH/AKX-CH-BAM/AKX-CH-WSS accessories ADS-USB (REQUIRED) DIRECTED XL-0 RF-KIT & ADS-HRN(RS)-XL0 (OPTIAL) DIRECTED
More informationII E INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT
II E1500-11 INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT KITS ARE UL LISTED UNDER CATEGORY GWVW, GWVW7 (CANADA) (ACCESSORY FOR USE ON FIRE EXIT HARDWARE AND PANIC HARDWARE). INDEX
More informationINSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT
INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT INDEX FUNCTION DESCRIPTION PAGE 1 PARTS LIST PAGE 2 TOOLS REQUIRED PAGE 2 KIT INSTALLATION INSTRUCTIONS PAGE 2-10 KIT ADJUSTMENT INSTRUCTIONS
More informationINSTALL GUIDE OEM-CH(RS)-CH4-[ADS-CH4]-EN
INSTALL GUIDE DOCUMENT NUMBER 864 REVISI DATE 77 FIRMWARE OEM-CH(RS)-CH4-[ADS-CH4] HARDWARE ADS-CH4 ACCESSORIES ADS-USB (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical
More informationinstall guide FLC-CH(RS)-CH4-[FLRSCH4]-EN
install guide Document number 655 Revision Date 098 firmware FLC-CH(RS)-CH4-[FLRSCH4] hardware FLRSCH4 accessories FLPROG (REQUIRED) FLRF//4 (OPTIAL) CARLINK ASCL (OPTIAL) NOTICE The manufacturer will
More information1. TECHNICAL DATA CAT200
CAT/200 3 17 From automazii 1000 226 216 500 1. TECHNICAL DATA CAT200 Power Supply Power supply for gearmotors Current Gearmotor power Torque Class of service Cycle ( work/pause) Temperature Protecti degree
More informationMotorized Electric Latch Retraction
; SECTION I: OVERVIEW 1. Description The Corbin Russwin MELR Electric Latch Retraction (ELR), refer to Figure 1, works with ED4000 & ED5000 Series exit devices to provide remote-controlled latch retraction
More informationONE TOUCH CONTROL BOX
ONE TOUCH CONTROL BOX CONVERSION KIT INSTRUCTIONS REMOVAL, INSTALLATION, OPERATION, AND REMOTE CONTROL PROGRAMMING THUNDERSTONE PART #101322 REVISION A JULY 14 TH 2016 2 P a g e INSTALLING THE THUNDER
More information56- Electric Latch Retraction Exit Devices Installation and Wiring Instructions
SECTION I: OVERVIEW 1. Description The Sargent 56- prefix ELR works with 80 Series exit devices to provide remote-controlled latch retraction. It is compatible with the following prefixes: 53 - Latchbolt
More informationINSTALL GUIDE ORB-AL(RS)-CH4-[ADS-ALCA]-EN
INSTALL GUIDE DOCUMENT NUMBER 8457 REVISI DATE 7 FIRMWARE ORB-AL(RS)-CH4-[ADS-ALCA] HARDWARE ADS-ALCA ESSORIES ADS-USB (REQUIRED) ADS-HRN-CH4 (REQUIRED) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer
More information* * E996L Series. E996L for Rim/Vertical. E996L for Mortise CAUTION
*921297-00* 921297-00 Electric Locking Trim E996L Series Installation Instructions CAUTION Product is shipped in Fail Safe (FS) configuration. Fail Safe configuration is required by code in some applications
More information2904 Power Supply Installation Instructions I-EA00041
FEATURES Controls an opening with electrified locking device and automatic door operator Separate inputs for activation switch on entry and exit sides of opening Separate 24 VDC outputs for fail safe and
More informationSystem Sump and Pump VICTRON MULTIPLUS COMPACT
System Sump and Pump VICTRON MULTIPLUS COMPACT 12/800/35 & 12/1200/50 - Advanced Battery Backup System Operatial Manual Rev 2.2-10 October 2017 Newt Waterproofing Systems INTRODUCTION CONTENTS The Victr
More information55 Series Exit devices
55 Series Exit devices The Von Duprin 55 Series is a range of push bar exit devices designed to suit single and double door applications with narrow stiles. The 55 Series can be used on aluminium hollow
More informationModel 2300JL Installation Guide
Model 2300JL Installation Guide POWER ACCESS CORPORATION 4 HERSHEY DRIVE, DOCK 4 ANSONIA, CT 06401 800-344-0088 WEBSITE: www.power-access.com EMAIL: salesinfo@power-access.com 1 STANDARD PARTS MODEL 2300JL
More informationAutomatic Roof Hatch Opener
Automatic Roof Hatch Opener Installation Guide REQUIRED TOOLS (These tools are required to complete the installation) Cordless Drill 1/8 1/4 Drill Bits 1/8 Pin Punch #2 Philips Bit Rachet Sharpie Hammer
More informationModel 2300DL Installation Guide
Model 2300DL Installation Guide POWER ACCESS CORPORATION 4 HERSHEY DRIVE, DOCK 4 ANSONIA, CT 06401 800-344-0088 WEBSITE: www.power-access.com EMAIL: salesinfo@power-access.com 1 STANDARD PARTS MODEL 2300DL
More informationBZ-150. Installation Instructions. Power Pack SPECIFICATIONS
SPECIFICATIS Voltages...120/. 50/60Hz Load Requirements Ballast... 20amp @120/ Incandescent... 20amp @ Motor... 1HP @120/240VAC Output...225mA @ (with relay connected) Input Control... 12- Hold... 12-
More informationSAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIS! SAVE THESE INSTRUCTIS AND DELIVER TO OWNER AFTER INSTALLATI IMPORTANT SAFETY INSTRUCTIS! WARNING To reduce the risk of death, injury or property damage from fire,
More informationA S S E M B L Y & I N S T A L L A T I O N G U I D E
A S S E M B L Y & I N S T A L L A T I O N G U I D E APPLICATION 2015-2016 2015-2016 PART # 7416-00A Silver 7416-01A Black INSTALLATION TIME 1 Hour 1 SKILL LEVEL 2 3 4 1= Easy TOOLS REQUIRED Phillips screw
More informationINSTALL GUIDE OEM-AL(RS)-CH5-[ADS-ALCA]-EN
INSTALL GUIDE OEM-AL(RS)-CH-[ADS-ALCA]-EN DOCUMENT NUMBER 8 REVISI DATE 00 FIRMWARE OEM-AL(RS)-CH-[ADS-ALCA] HARDWARE ADS-ALCA ACCESSORIES ADS-USB (REQUIRED) ADS-HRN-CH (REQUIRED) NOTICE The manufacturer
More informationINSTALLATION INSTRUCTIONS CRL JACKSON 2085E
INSTALLATION INSTRUCTIONS CRL JACKSON 2085E ELECTRIC LATCH RETRACTION CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com
More informationINFINITY MULTA SERIES
ASSEMBLY ASSEMBLY INSTRUCTIONS INSTRUCTIONS ASSEMBLY INSTRUCTIONS INFINITY MULTA SERIES Workstations, WORKSTATIONS, desks, DESKS, and AND tables TABLES with WITH powered POWERED ADJUSTMENT adjustment PARTS
More informationHANDLING MECHANICAL INSTALLATION
2 INSTALLATION DESCRIPTION The and 2 Delay Egress Systems are 1500 pound holding force (holding force not evaluated by UL) per leaf electromagnetic locks, electronically controlled to provide a 15 or 30
More informationReplacing Your 2nd Generation Battery Pack
Replacing Your 2nd Generation Battery Pack Video tutorial: https://www.youtube.com/watch?v=xvcfwpo8rok Tools needed: 4mm hex tool. If you do not have a hex wrench, please email us at recall@boostedboards.com
More informationSmartLock Accessories
CANSEC ACCESSORIES SmartLock Accessories CA SLbox CA SLBOX SmartLock enclosure 9.5 x 13 x 3 metal enclosure with room for 1 or 2 SmartLock controllers, Cansec power supply and 12V 7 AH battery C Ca ps123a
More information9700/F9700 SERIES RIM EXIT DEVICE
INSTALLATION INSTRUCTIONS 9700/F9700 SERIES RIM EXIT DEVICE Index: Screw chart Tools required Outside trim options "03" Additional door prep Device installation Options available 5300 retro-fit preparation
More informationIL500 Sierra Inclined Platform Lift
IL500 Sierra Inclined Platform Lift Installation & Service Manual www.harmar.com 800-833-0478 IMPORTANT: Read and understand this manual thoroughly before attempting to install or operate the lift. If
More informationMarlon Xplore II / Xplore Pro II Deck Installation & Assembly Instructions
Marlon Xplore II / Xplore Pro II Deck Installation & Assembly Instructions Marlon Recreational Products www.marlonproducts.com 1-800-663-7367 INSTALLATION INSTRUCTIONS: 1. Remove the ramp from underneath
More informationINSTALLATION INSTRUCTIONS DEGR7700 DELAYED EGRESS ALL IN ONE DEVICE
INSTALLATI INSTRUCTIS DEGR7700 DELAYED EGRESS ALL IN E DEVICE Stop Employee Theft Stop Retail Shoplifting Restrict Airport Patrons Restrict Wandering Patients SOUNDS. DOOR CAN BE The sign provides comprehensive
More informationASSA ABLOY. Installation Instructions. MP9800 Series Multi-Point Lock with MELR Option (Electric Latch Retraction)
Installation Instructions MP9800 Series Multi-Point Lock MP9800 Series Multi-Point Lock, the global leader in door opening solutions 1 of 20 Copyright 2016 Corbin Russwin Inc., an Group company. Table
More informationINSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks
Securitron Magnalock Corp. Tel 775.355.5625 550 Vista Boulevard Fax 775.355.5633 Sparks, NV 89434 info@securitron.com www.securitron.com ASSA ABLOY, the global leader in door opening solutions INSTALLATION
More informationTOYOTA VENZA HANDS FREE BLU LOGIC Preparation
TOYOTA VENZA 2009- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationInstallation Instructions
Approx. Install Time 3Hrs 00Min Installation Instructions Vehicle Application Year: 2013-2017 Make: Ram Model: 2500/3500 Diesel Engine: 6.7L Cummins Tools Required 7mm, 8mm, 10mm,& 13mm Wrench & Socket
More informationINSTALLATION INSTRUCTIONS & MANUAL BOOK FOR ARCHITECTS, GENERAL CONTRACTORS & DEALERS REV-2
INSTALLATI INSTRUCTIS & MANUAL BOOK FOR ARCHITECTS, GENERAL CTRACTORS & DEALERS REV-2 C Applied Applied MODEL: MIRACLE 1 HIGH-QUALITY, MECHANICAL, LINEAR OPERATOR FOR SWING GATES COPYRIGHT 1998 ELITE ACCESS
More informationCONTROLLER DIAGNOSTIC GUIDE
Proprietary tice: This document contains proprietary information which not to be reproduced, transferred, to other documents, disclosed to others, used for manufacturing or any other purpose without the
More informationELR Series Multi-Point Lock Installation Instructions
7000 ELR Series Multi-Point Lock Installation Instructions Copyright 2015, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the
More informationOWNER S MANUAL MODEL SW470 MEDIUM DUTY SWING GATE OPERATOR MODEL SW490 HEAVY DUTY SWING GATE OPERATOR
CTROLLER BOARD GL OWNER S MANUAL MODEL SW470 MEDIUM DUTY SWING GATE OPERATOR MODEL SW490 HEAVY DUTY SWING GATE OPERATOR MODEL SW470 MODEL SW490 MODELS SW470 AND SW490 ARE FOR VEHICULAR PASSAGE GATES LY
More informationTOYOTA CAMRY HANDS FREE BLU LOGIC Preparation
TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationPlasma Display Electric Pop-Up Lift (PUL)
I N S T R U C T I O N M A N U A L Plasma Display Electric Pop-Up Lift (PUL) Your is designed for installation in furniture or cabinets. Display mounting is made easy using the Q-latch mounting system and
More informationKWIKEE DOOR SWITCH STEP ACTIVATION INSTALLATION GUIDE ( )
Purpose Note: Information for this document has been obtained from Kwikee Products document number 1421330, Revision 0B, dated February 2008 and updated for current practices. This document explains the
More informationM670/M680BD MAGNALOCK SERIES Installation Instructions
Securitron www.securitron.com Tel 800.624.5625 techsupport@securitron.com M670/M680BD MAGNALOCK SERIES Installation Instructions Page 1 Rev. D, 12/14 Table of Contents Package Contents... 3 Mounting Hardware...
More information2Installation CHAPTER TWO IN THIS CHAPTER
CHAPTER TWO 2Installati IN THIS CHAPTER Product Ship Kit List Quick Test Motor Selecti and Wiring Drive Cfigurati DIP Switches, I/O, Potentiometers Mounting the Drive and Motor; Attaching the Load Testing
More informationCV41. Vehicle Mounting Kit. Reference Guide
CV41 Vehicle Mounting Kit Reference Guide CV41 Vehicle Mounting Kit Reference Guide........... 3 Secure the Smart Dock to a Vehicle.................... 3 Supply Power to the Smart Dock......................
More informationPlease forward any questions or comments regarding this Troubleshooting Guide to
2009 Human Touch, LLC. All rights reserved. May 28, 2009 Please forward any questions or comments regarding this Troubleshooting Guide to documentation@humantouch.com. HT-1650 Troubleshooting This Troubleshooting
More informationMcDonalds Installation Guide
McDonalds Installation Guide Canopy COD Installation CCOD ------------------------------------------------------------------------------------------------------ Metal Pedestal COD Installation MCOD Everbrite
More informationCRS-2000 AND CRS-3000 SUPPLEMENT TO WORLD CRUISE 2 OR GLOBAL CRUISE INSTALLATION MANUAL
CRS-2000 AND CRS-3000 SUPPLEMENT TO WORLD CRUISE 2 OR GLOBAL CRUISE INSTALLATI MANUAL This supplement provides some information and guidelines to help in the installation of this cruise control into street
More informationinstall guide COM-IDS(RS)-BM1-[ADS-BM1]-EN
install guide Document number Revision Date 50 firmware COM-IDS(RS)-BM-[ADS-BM] hardware ADS-BM accessories ADS-USB (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) NOTICE The manufacturer
More informationMaster/Slave Actuators Spring Return Rotary 24 Vac - Modulating Control
Document No. 129-312 Master/Slave Actuators Spring Return Rotary 24 Vac - Modulating Control a PL0038R1 c b d e f g i Figure 1. Parts of the Master/Slave Actuators. h a. Actuator b. Shaft adapter c. Position
More informationRollstar Shade Installation Instructions
Rollstar Shade Installation Instructions All Lifting Systems Inside or Outside Mount Thank you for purchasing your new Rollstar shade. It has been custom-made from the highest quality materials to the
More informationSolar & Roller Shades
STEP BY STEP INSTALLATION INSTRUCTIONS Solar & Roller Shades Loop Control, Loop Control with Cassette/2 on 1 Headrail & Loop Control with Metal Valance Table of Contents Step 1 - Getting Started....3 Everything
More informationOwner s Manual. Series 6050 and Vehicular Swing Gate Operator. Copyright 2010 DoorKing, Inc. All rights reserved. WARNING
CERTIFIED TO CAN/CSA C22.2 NO. 247 53382 VEHICULAR GATE OPERATOR CLASS HP MODEL SERIAL AMPS 60 Hz MAX GATE LOAD DoorKing, Inc., Inglewood, CA MOVING GATE CAN CAUSE SERIOUS INJURY OR DEATH Operate gate
More informationTOYOTA TUNDRA HANDS FREE BLU LOGIC Preparation
TOYOTA TUNDRA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationTOYOTA FJ CRUISER 2007 HANDS FREE PHONE INTERFACE 7/10/06
7/10/06 Part Number: 00016-00003-02 Accessory Code: BT1 Kit Contents Item # Quantity Reqd. Description 1 1 UIB -USER INTERFACE 2 1 CONTROL MODULE 3 1 USER GUIDE 4 1 HARDWARE BAG 5 1 INSTALLATION INSTRUCTIONS
More informationPart No EWP & FAN DIGITAL CONTROLLER INSTRUCTIONS
77 Taras Avenue P.O. Box 363 Altona North Vic 3025 Australia Phone: +61(0)3 9369 1234 Fax: +61(0)3 9369 3456 Email: info@daviescraig.com.au Web: www.daviescraig.com.au Part No. 8020 - EWP & FAN DIGITAL
More informationProduct Guide. If it has wires think... Command Access!
Product Guide 41 If it has wires think... Command Access! ABOUT US Our goal is to serve the customer to the best of our ability every time! Command Access is a manufacturer and modifier of high quality
More informationUNIVERSAL REMOVABLE REAR CROSSBAR CONVERSION INSTRUCTIONS FOR HAULER RACK II & SERVICE BODY SERIES RACKS
UNIVERSAL REMOVABLE REAR CROSSBAR CONVERSION INSTRUCTIONS FOR HAULER RACK II & SERVICE BODY SERIES RACKS T11U2863-1 shown above Package Contents: (2) Y BRACKETS (8) 3/8-16 x 2 CARRAIGE BOLTS (4) 3/8-16
More informationSpectra Class. N6000 Series Exit Devices SECURITY DOOR CONTROLS. N6100 Rim Mount Exit Device. N6200 Surface Vertical Rod Exit Device.
N6000 Series Exit Devices Spectra Class Rim Mount Surface Vertical Rod N6100 Rim Mount Exit Device For use on single doors or pair of doors with mullion 1-3/4"(44 mm) door thickness standard. Specify thickness
More informationElectrical Options Booklet. Table of Contents
*24228413* 24228413 Electrical Options Booklet Table of Contents EL Wiring... EL Troubleshooting... SD/EL 98/99 Cylinder Dogging... SS Wiring... 330, 350, RX-330 and RX-350 Push Bar Trim Mechanical Installation...
More informationA S S E M B L Y & I N S T A L L A T I O N G U I D E
A S S E M B L Y & I N S T A L L A T I O N G U I D E APPLICATION Deep Bed Truck (F-150 & Tundra) Large Truck, Universal (Full-size trucks, wide beds) Small Truck, Universal (Mid-size and small trucks, small
More informationASSEMBLY & INSTALLATION GUIDE. INSTALLATION TIME 1 Hour SKILL LEVEL. 1= Easy TOOLS REQUIRED
ASSEMBLY & INSTALLATION GUIDE APPLICATION Deep Bed Truck (F-150 & Tundra) Large Truck, Universal (Full-size trucks, wide beds) Small Truck, Universal (Mid-size and small trucks, small beds) PART # 74813-00A
More information8. Do not install this product on the exterior of buildings. 9. Do not use as a doorstop. This will void warranty. Installation Instructions
INSTALLATI DE8310 Delayed Egress Electromagnetic Locks Pre-Installation Instructions 1. This product must be installed according to all applicable building and life safety codes. All installations must
More informationConflicts: JBL Audio, Factory Navigation, Accessory XM Satellite Radio, and Accessory Sirius Satellite Radio
TOYOTA YARIS SEDAN 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts: JBL Audio, Factory Navigation,
More informationE-AC Drive Hardware Installation Guide
p/n 88-020292-01 A Automati E-AC Drive Hardware Installati Guide Effective: April 9, 2002 User Informati WARNING!! E Series products are used to ctrol electrical and mechanical compents of moti ctrol systems.
More informationTOYOTA RAV HANDS FREE PHONE INTERFACE 9/06/06
9/06/06 Part Number: 00016-32103-01;00003-04 Accessory Code: BT1 Kit Contents Item # Quantity Reqd. Description 1 1 UIB -USER INTERFACE 2 1 CONTROL MODULE 3 1 USER GUIDE 4 1 HARDWARE BAG 5 1 INSTALLATION
More informationREF QTY PART DESCRIPTION PART NUMBER 1 1 Side Mirror, Driver (Not Shown) 1 Loctite - 263, 0.5 ml, Red Instructions
MIRROR KIT P/N 2881001, 2881002, 2881011, 2881012 APPLICATION em1400, em1400 LSV or M1400 BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain
More informationinstall guide OEM-IDS(RS)-BM1-[ADS-BM1]-EN
install guide Document number 9 Revision Date 50 firmware OEM-IDS(RS)-BM-[ADS-BM] hardware ADS-BM accessories ADS-USB (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical
More informationSCION TC HANDS FREE BLU LOGIC Preparation
SCION TC 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00099 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationFabric Studio Custom Roll Shades Installation Instructions
Fabric Studio Custom Roll Shades Installation Instructions Cassette System Battery Motor Lifting System Inside or Outside Mount Thank you for purchasing your new roll shade. It has been custom-made from
More informationUniversal Pitch Adjustable Wall Mount For Flat Panel Display UPM-2401
INSTALLATION INSTRUCTIONS Universal Pitch Adjustable Wall Mount For Flat Panel Display UPM-2401 Your new Chief Universal Pitch-Adjustable Wall Mount (UPM-2401) is a quick disconnect mounting system with
More informationSection 55 Chapter 6
Section 55 Chapter 6 REMOTE HYDRAULICS CONTROLLER Calibration and Fault Codes 6-12880NH TABLE OF CONTENTS REMOTE HYDRAULICS CONTROLLER CALIBRATION... 55-5 Requirements For Calibration... 55-5 Aux Set Main
More informationINSTALLATION INSTRUCTIONS CRL ESK2/ESP2
INSTALLATION INSTRUCTIONS CRL ESK2/ESP2 ELECTRIC STRIKE KEEPER FOR DOUBLE DOORS NOTE: Sensor feature available on ESP s only. ALUMINUM Phone: (800) 421-6144 Fax: (800) 587-7501 crlaurence.com usalum.com
More informationAlarms & Remote Start
Alarms & Remote Start INSTALL GUIDE DOCUMENT NUMBER 5866 REVISION DATE 0607 FIRMWARE OEM-IDS(RS)-BM-[OL-RS-BM] HARDWARE OL-RS-BM ACCESSORIES OL-LOADER (REQUIRED) NOTICE The manufacturer will accept no
More informationTOYOTA 4-RUNNER 2006 HANDS FREE PHONE INTERFACE 7/24/06
7/24/06 Part Number: 00016-00003-02 Accessory Code: BT1 Kit Contents Item # Quantity Reqd. Description 1 1 UIB -USER INTERFACE 2 1 CONTROL MODULE 3 1 USER GUIDE 4 1 HARDWARE BAG 5 1 INSTALLATION INSTRUCTIONS
More informationSolar Powered. Solar Powered. Model Installation/Owner s Manual. Solar Powered Vehicular Swing Gate Operator
Installation/Owner s Manual Model 6524-081 Solar Powered Vehicular Swing Gate Operator Use this manual for circuit board 4100-010 Revision AA or higher. 6524-066-S-5-18 For AC Power, See 6524-065 AC Power
More informationlkm7001 key override module Installation Instructions Converting The LKM7000 to The LKM7003
lkm7001 Instructions Converting The LKM7000 to The LKM7003 key override module In A Single Motion, We ll Change The Way You Think About Security Read Instructions thoroughly prior to installation Base
More informationService Manual ISO7000R Recumbent Bike
Service Manual ISO7000R Recumbent Bike Before Using this product, read this manual and follow all safety rules and operating instructions. Maintenance The ISO7000R is virtually maintenance free. After
More informationASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY
00 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) Track Assembly (0-) / Replacement
More informationE R A I INSTALLATION MANUAL. Gate Opener Department MERCURIO 302 F MERCURIO 502 F MERCURIO 802 F MERCURIO 501 F
S E R A I Gate Opener Department MERCURIO 302 F MERCURIO 502 F MERCURIO 802 F MERCURIO 501 F INSTALLATI MANUAL SR 29.75 F KIT WITH ENCODER FOR SLIDING GATES (UP TO 300 kg -230V~) SR 24.29 F KIT WITH ENCODER
More informationWARNING GATE LOCK MODEL SGLOCK12V
GATE LOCK MODEL SGLOC2V The SGLOC2V Automatic is compatible with LiftMaster Gate Access Systems LA412, LA412-S, and RSW operators. The purpose of the automatic gate lock is to securely lock the gate in
More informationINSTALL GUIDE AKX-IDS(RS)-BZ1B-[ADS-BZ1]-EN
INSTALL GUIDE DOCUMENT NUMBER 25893 REVISION DATE 2627 FIRMWARE AKX-IDS(RS)-BZ1B-[ADS-BZ1] HARDWARE ADS-BZ1 ESSORIES ADS-USB (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) DIRECTED SMART & ADS-HRN(RS)-SM (OPTIONAL)
More information200 Shadylane Drive Philipsburg, PA Phone: (814) Fax: (814) Service Manual. Model 642E Centrifuge
200 Shadylane Drive Philipsburg, PA 16866 Phone: (814) 342-6205 Fax: (814) 342-4510 www.druckerdiagnostics.com Service Manual Model 642E Centrifuge MODEL 642E SERVICE MANUAL REV: Original Issue 1 CONTENTS
More informationADDENDUM MODEL S3 OPERATORS Models: SL/540/570/580/590 & SW420/470/490
ADDENDUM MODEL S3 OPERATORS Models: SL/540/570/580/590 & SW420/470/490 This addendum is to be used in conjunction with the owner s manual included with this operator. Refer to this addendum for all programming
More informationField Replacement of Fluorescent Power Supply in L-858 Signature Series Sign
Field Replacement of Fluorescent Power Supply in L-858 Signature Series Sign Document No. Issued: December 13, 2006 Rev. C: March 25, 2008 ADB Airfield Solutions Copyright 2009 by ADB Airfield Solutions.
More informationINSTALL GUIDE OEM-AL(RS)-CH8-[FLCAN]-EN
INSTALL GUIDE DOCUMENT NUMBER 5644 REVISI DATE 084 FIRMWARE OEM-AL(RS)-CH8-[FLCAN] HARDWARE FLCAN ESSORIES FLPROG (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly intended
More informationEPS LH DRIVE KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev 01 04/16 Page 1 of 11. E2, E4, E6, and el XD
EPS LH DRIVE KIT P/N 2881862 APPLICATION E2, E4, E6, and el XD BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation instructions
More informationARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI
II 1400-6 ARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI ACSI 1426-04-AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1092, REV. C INSTALLATION For C-UL Listed applications,
More informationAdams rite. Exit Devices & parts exit devices series exit device parts
Adams rite Exit Devices & parts exit devices 8099 8211 8099 Active Dummy Bar with Switch Can be wired normally open or normally closed to operate maglock, alarm, etc No latching mechanism 8211 Surface
More informationInstallation and Wiring Instructions for the TL- Prefix SARGuide Illuminated Touchpad for 80 Series Exit Devices to ElectroLynx Connector System
Installation and Wiring Instructions for the TL- Prefix SARGuide Illuminated Touchpad for 80 Series Exit Devices to ElectroLynx Connector System U.S. Patent No. 7,04,050 For assistance, contact SARGENT
More informationSPEEDKEY KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 9. GEM e2, e4, e6, el XD
SPEEDKEY KIT P/N 2883054 APPLICATION GEM e2, e4, e6, el XD BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation instructions
More informationSCION XB HANDS FREE BLU LOGIC Preparation
SCION XB 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More information