SCION TC HANDS FREE BLU LOGIC Preparation

Transcription

1 SCION TC HANDS FREE BLU LOGIC Preparation Part #: PT Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured on or after 19D0, installation kits will include BLU Logic Switch Decal. The manufacturing date code is on the part label of the packaging box and is printed as DDMY. Please note that this manufacturing date is per Toyota standards and is in the format of DAY-DAY-MONTH-YEAR. Example: 31L8 date on label means 31st, December, Item 1 Item 2 Item 3 Item 4 Item 5 Item 6 Item 7 Item 8 Item 9 Item 10 Hardware Content Item# Quantity Reqd. Description 1 1 Interface Module 2 1 Main Power Harness 3 1 BLU Logic Switch 4 1 Switch Extension Cable 5 1 Microphone Lock Ties 7 2 Adhesive Foam Pad 8 1 Owner s Manual 9 33cm 1/4 Wire Split Loom 10 1 BLU Logic Decal Additional Items (may be required) Item# Quantity Reqd. Description Recommended Sequence of Application Item# Accessory General Applicability Note: Recommended Tools Personal & Vehicle Protection Safety Goggles Seat Covers Floor Covers Special Tools Legend Notes Panel Clip Removal SST # Sockets 10 mm Screwdriver Phillips, #2 Torque Wrench Installation Tools Masking Tape Foam Tape Special Chemicals Cleaner 36 in-lb (4.07 N.m) Notes VDC Supplied VDC Supplied Notes VDC Approved Cleaner STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. CAUTION: A process that must be carefully observed in order to reduce the risk of damage to the accessory/vehicle. OPERATOR SAFETY: Use caution to avoid risk of injury. TOOLS & EQUIPMENT: Used in Figures to call out the specific tools and equipment recommended for the process. Vehicle Service Parts (may be required for reassembly) Item# Quantity Reqd. Description REVISION MARK: This mark highlights a change in installation with respect to previous issue. SAFETY TORQUE: This mark indicates that torque is related to safety. VIDEO: Video Available; click to Play Page 1 of 10

2 SCION TC HANDS FREE BLU LOGIC Preparation Table of Contents I. Preparation Table Of Contents Content Location...3 II Vehicle Preparation Vehicle Disassembly Interface Module Installation Microphone Installation BLU Logic Switch Installation Apply BLU Logic Decal to Switch...9 III. Checklist Accessory Function Checks Vehicle Function Checks...10 Accessory Installation Practice (read before installation) Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the Accessory Installation Practices document. This document covers such items as: Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.) Safety (eye protection, checking torque procedure, etc.) Vehicle Disassembly/Reassembly (panel removal, part storage, etc.) Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.) Please see your Toyota/Scion/Lexus dealer for a copy of this document. Page 2 of 10

3 SCION TC HANDS FREE BLU LOGIC Preparation Content Location 1 Interface Module 2 Wired Microphone 3 BLU Logic Switch Location Page 3 of 10

4 Socket (10 mm), Ratchet 1. Vehicle Preparation (Fig. 1-1) a. Apply parking brake. b. Protect fender before starting. c. Remove the negative ( ) battery cable. Fig. 1-1 CAUTION: Do not touch the positive terminal with any tool during removal. d. Using the protective blanket, cover front seat, side of the shift lever and center console. e. Place removed vehicle components on a protective blanket. Panel Removal Tool 2. Vehicle Disassembly MANUAL TRANSMISSION MODELS ONLY. a. Remove the gearshift knob, then loosen the console panel (Fig. 1-2). 1. Remove the side trim garnishes. 2. Disconnect all connectors. Fig. 1-2 Panel Removal Tool AUTOMATIC TRANSMISSION MOD- ELS ONLY. NOTE: Automatic transmission vehicles must be left in Drive before disconnecting the battery. Otherwise the shift bezel and radio bezel cannot be removed. b. Loosen the console panel. 1. Remove the side trim garnishes (Fig. 1-3). 2. Disconnect all connectors. Fig. 1-3 Page 4 of 10

5 Panel Removal Tool c. Remove radio bezel. 1. Apply protective tape to the right of the bezel. 2. Use panel removal tool to disengage and remove (Fig. 1-4). 3. Disconnect all connectors. Fig mm Socket/Ratchet & Phillips Screwdriver d. Remove the radio. 1. Remove two (2) bolts on top of the radio using a 10mm ratchet/socket (Fig. 1-5). 2. Remove two (2) Phillips screws on the bottom of the radio (Fig. 1-5). 3. Disconnect all connectors and set aside. Fig. 1-5 NOTE: Be careful not too put too much tension on the connections. 3. Interface Module Installation a. Mount the module to the bottom right of the radio opening. NOTE: DO NOT remove protective foam wrap from module. 1. Interlock two (2) wire ties and secure the module to the support bar to the right of the radio opening (Fig. 1-6). NOTE: Rollover Image is a close up view of the mounting position. BLU Logic wire ties in Figure 1-6 and the remainder of these instructions will be shown in yellow. Additional taped wiring bundles are part of aftermarket Navigation radio. Page 5 of 10

6 4. Microphone Installation a. Mounting the microphone. 1. Remove lower portion of the steering column (Fig. 1-7). 2. Clean the microphone location with VDC approved cleaner (Fig. 1-7). Fig. 1-7 ~5-10 mm 3. Apply 33 cm of the 1/4 wire split loom to the microphone end of the cable leaving a minimum of 8 mm of exposed wire (Fig. 1-8). 4. Secure the wire loom with tape. ~5-10 mm 5. Mount the rear of the microphone approximately 5-10 mm from the edge of the panel and approximately 5-10 mm from the top of the panel to minimize the amount of exposed wire visible to the customer (Fig. 1-8). Fig. 1-8 NOTE: 0-20 mm of exposed wire is acceptable. b. Route the microphone wire (highlighted in blue). 1. Lower steering column to provide sufficient space to route cable. 2. Route behind the mounting panel towards the opening of the radio (Fig. 1-9). CAUTION: When steering wheel is tilted up/down make sure microphone wire does not rub against steering wheel column. Fig. 1-9 Page 6 of 10

7 3. Connect the microphone to the module. 4. Remove most of the microphone wire slack, bundling the excess to the existing wire loom with wire a tie circled in Fig NOTE: The microphone wire between the bundle and the microphone will be secured later. Fig BLU Logic Switch Installation a. Route the switch cable. 1. Route through the opening of the radio towards the driver side knee panel (Fig. 1-11). NOTE: Switch wire is highlighted in blue. Fig Move the steering column up. 3. Continue routing under the steering column over towards the fuse panel (Fig. 1-12). Fig Page 7 of 10

8 4. Using your hands, carefully remove the fuse panel cover (Fig. 1-13). 5. Reach up and remove the far left knock-out. NOTE: If far left plug is occupied, use next available knock-out. Fig Secure switch cable to existing BLACK wire loom with wire tie(s) (Fig. 1-14). NOTE : Telescope the steering wheel all the way out to verify wires won t be pulled or stretched. Switch wire is highlighted in orange. 7. Wire tie every 5-6 inches. 8. Cut off excess wire ties. b. Mount the BLU Logic switch with the solid arrow pointing up and connect it to the pig tail. 1. Reinstall the fuse panel cover. Fig Reinstall lower portion of the steering column. 3. Remove any slack and secure the microphone and switch cables to the existing wire loom to the right of the metal bracket (Fig 1-15). 4. Wire tie the wires so they DO NOT come in contact with the metal brackets. NOTE: This is on the left side of the radio opening. Fig Page 8 of 10

9 c. Connect the main power harness to the interface module (Fig. 1-16). NOTE: The Red connector is connected to the matching Red connector on the module. d. Connect the switch cable to the interface module. e. Connect the main power harness to the matching radio connections. Fig NOTE: AVC-LAN (12 pin) connector may not be present on the vehicle s harness. Wire tie this connector to the harness unconnected, but ALWAYS connect the AVC-LAN (12 pin) connector into the radio. If AVC-LAN (12 pin) connector is present on vehicle harness, connect to jumper provided with BLU Logic unit. If any other accessories are installed that connect to the head unit, BLU Logic should be the unit that plugs into the radio first. f. Reinstall the radio g. Reinstall all panels h. Position negative battery cable at the original factory position (tighten the nut to 36 in-lbs (4.07 N.m). Fig CAUTION: Do not touch the positive terminal with any tool during installation. i. Put owner s manual in the glove box. 6. Apply BLU Logic decal to BLU Logic switch. (Only kits manufactured on or after the date code on the front page will include the BLU Logic decal). a. Remove the protective backing on the round portion of the BLU Logic sticker (Fig. 1-17). b. Stick it to the center of the switch so that the sticker hangs towards the right as shown in Fig Fig NOTE: Photo shown may not match the switch installation location for this vehicle and is for illustrative purposes. Page 9 of 10

10 CHECKLIST these points MUST be checked to ensure a quality installation. Make sure radio and interior lights (if applicable) are turned off. Install fuse (short pin) for the following function checks. Accessory Function Checks Check: Factory Radio Interface Kit Audio Output Vehicle Function Check Vehicle Function Look For: Turn on the radio and verify that the BLU Logic Module will mute the audio. With the radio on, press the middle button on the BLU Logic switch and verify that the audio is muted. Verify the proper connection of the Interface kit by pressing and holding the middle button on the switch until you hear one (1) beep. NOTE: Pairing the module to a phone is not required. This is the customers (or dealers) responsibility. Turn the radio to an AM or FM station and then turn the balance to the L and confirm the audio is coming from the left front speaker. Repeat for the right front speaker. Vehicle Function Detail Audio AM/FM Verify the proper operation of audio AM/FM. Hazard Switch Verify the proper operation of the hazard switch. HVAC Verify the proper operation of the air conditioning system. NAV System (if equipped) Confirm navigation operation by AVN diagnostics. 12V AUX Plug Verify the proper operation of the 12V AUX Plug. AUX Input (if equipped) Verify the proper operation of the Aux plug. Ipod Input (if equipped) SRS Warning Light Tire Pressure Monitoring System (TPMS) Verify the proper operation of the Ipod Input. Confirm SRS warning light illuminates for approximately 6 seconds with the ignition ON, and then goes out. Prior to TPMS activation and Pre- delivery Service (PDS) of the Vehicle the TPMS light will blink when IG is turned on. After TPMS activation and PDS of the Vehicle the TPMS light will illuminate for a few seconds and go off when IG is turned on. Turn off all components including radio and interior lights. Remove fuse (short pin) after function checks are complete. Check with your dealer/port to find out if this step is required. Kit Service Information Item: Location: 1 3-Amp in-line Fuse The fuse is located behind the HVAC assembly. To replace, follow Step 1 through 4 to access the fuse location. NOTE: If the fuse is blown, the Hands Free BLU Logic will not turn on. Note: Initialization of vehicle components may be necessary if accessory installation is performed after PDS. Reference the applicable PDS instruction for initialization procedures. Page 10 of 10