VLP-UL-KIT INSTALLATION INSTRUCTIONS. The VLP-UL-KIT for 36 or 48 is a field installable solenoid latch pullback for the Von Duprin 33/35 &

Size: px
Start display at page:

Download "VLP-UL-KIT INSTALLATION INSTRUCTIONS. The VLP-UL-KIT for 36 or 48 is a field installable solenoid latch pullback for the Von Duprin 33/35 &"

Transcription

1 Solenoid VLP-UL-KIT INSTALLATION INSTRUCTIONS The VLP-UL-KIT for 36 or 48 is a field installable solenoid latch pullback for the Von Duprin 33/35 & 98/99 series exit devices..050 Hex Wrench retraction pin connecting rod end PM300 Wire Loop Plunger/Connecting Rod for 36 3/3 Hex Wrench Connecting Rod for 48 Solenoid Mount Screws Tools Required Cordless Drill or Phillips Screwdriver Installation Video Click or Scan U.S. Customer Support Visit our website for more details Canada Customer Support Doc # 030_A

2 TECHNICAL INFORMATION Specifications Wires: Input to PM300 non-polarized Black (+)(-) Operating Voltage Range: -30 VDC Coil Resistance - Primary Coil: ohms; Holding Coil : 5 ohm Output from PM300: Yellow=Pull Coil; Orange= Hold Coil; Green=Common Standard Mode Fuse: Glass 3.5-5A, Resettable A trip Relay: 5A or greater High Output Mode Fuse: Resettable A trip Relay: 0A or greater Switch Scan me PM300 Compatibility Chart Troubleshooting & Diagnostics Symptom Possible Cause Solution Solenoid pulls back but releases immediately Solenoid plunger not seating correctly - Check plunger rod adjustment. - Check vertical rod adjustment. - Make sure the plunger set screw has been installed correctly. Solenoid pulls back and holds, but does not retract latch far enough Plunger rod out of adjustment Check plunger rod adjustment Solenoid has excess delay time and/or drop out. Wire run exceeding the maximum recommended distance Locate power supply within the distances specified U.S. Customer Support Visit our website for more details Canada Customer Support Doc # 004

3 Electrified Exit Device Installation Example Optional Module Placement CAT GREEN CHANNEL LED Module Ceiling Tile NORMALLY OPEN DRY CONTACT FROM ACCESS CONTROL SYSTEM NO VOLTAGE LOCKING HARDWARE + - Module Legend Standard Placement Optional Placement RECOMMEND POWER SUPPLIES: All Command Access exit devices & field installable kits have been thoroughly cycle tested with Command Access power supplies at our factory. PS0 PS0/0B PS440B PS480B PS PS/B For more information click here or go to our website PS5-4 PS5-6 3

4 SLIDE TO REMOVE Remove push bar Remove mechanism case SLIDE TO REMOVE Baseplate Assembly Install cylindrical connecting rod end into the lock stile activating bracket by inserting the retraction pin and setting Install cylindrical the /6 connecting hex set screw. rod end into the lock stile activating bracket by inserting the retraction pin and setting the /6 hex set screw. set screw retraction pin BASEPLATE ASSEMBLY 4

5 BASEPLATE ASSEMBLY Completely thread the plunger/connecting rod into its cylindrical connecting rod end by finishing it through the shock 3 damper catch and setting the 3/3 hex screw. Completely thread the plunger/connecting rod into its cylindrical connecting rod end by fishing it through the shock damper catch and setting the 3/3 hex set screw. Note: Kit comes packed for 36 device. For 48 devices, remove plunger and re-assemble it with the connecting rod for the 48 model 98/99 Device SLIDE TO INSTALL set screw Install the solenoid by inserting the plunger into the solenoid housing and installing the two solenoid attachment screws (w/ lock washers) through the last two holes on the baseplate. Install the solenoid by inserting the plunger into the solenoid housing and installing the two solenoid attachment screws (w/ lock washers) through the last two holes on the baseplate. Reassemble device. Place the PM300 in the area between the solenoid and the end cap. 4 INSTALL PUSH BAR Page 4 PUSH BAR GUIDE CAT7 INSTALL Install mechanism case Note: Make sure crosspieces inside push Note: Make sure crosspieces bar are placed in slots in bellcranks. inside push bar are placed in slots in bellcranks. SLIDE TO INSTALL Baseplate Assembly 5

6 Drill solenoid cable hole in door between end cap bracket mounting holes. Leave off dogging cover and end cap until wires are routed. 5/8 Diameter cable hole End cap bracket mounting holes 7 Adjustment Bolt (3/8 ) Set screw (3/3 Allen) For plunger rod rod adjustment: adjust:. Release Release set set screw. screw. Turn adjustment bolt clockwise Turn adjustment to reduce bolt slack, and clockwise to reduce slack, counter-clockwise to increase and counter-clockwise to slackincrease slack. 3. Reset set screw 3 Reset set screw. WARNING: Failure Failure to reset to reset set set screw can result screw in can irreversible result in irreversible solenoid damage. solenoid damage. PM300 diagram A 6

PD10-UL-M KIT. I N S E R T I n s t r u c t i o n s A. B. C. D. E. E. E.

PD10-UL-M KIT. I N S E R T I n s t r u c t i o n s A. B. C. D. E. E. E. PD10-UL-M KIT I N S E R T I n s t r u c t i o n s The PD10-UL-M-KIT is a field installable motorized latch pullback for the PD10/11, Doromatic or Falcon 1690/1790, & First Choice 3600/3700. A. B. C. D.

More information

VLP-UL-M-KIT INSTALLATION INSTRUCTIONS

VLP-UL-M-KIT INSTALLATION INSTRUCTIONS VLP-UL-M-KIT INSTALLATION INSTRUCTIONS The Command Access VLP-UL-M-KIT is a field-installable motorized latch-pullback kit for the Von Duprin 33/35 & 98/99 series devices. F. G. i. H. j. K. D. Kit Includes

More information

PD10-M-RIM INSTALLATION INSTRUCTIONS. The PD10-M-RIM is a storefront grade 1 exit device equipped with motor drive latch retraction.

PD10-M-RIM INSTALLATION INSTRUCTIONS. The PD10-M-RIM is a storefront grade 1 exit device equipped with motor drive latch retraction. PD10-M-RIM INSTALLATION INSTRUCTIONS The PD10-M-RIM is a storefront grade 1 exit device equipped with motor drive latch retraction. Retrofits Doromatic 1790 & First Choice 3790. B. G. A. C. D. E. F. PD10-M-RIM

More information

PD18-RIM INSTALLATION INSTRUCTIONS

PD18-RIM INSTALLATION INSTRUCTIONS PD18-RIM INSTALLATION INSTRUCTIONS The PD18-RIM is a storefront grade 1 exit device equipped with motor driven latch retraction. Retrofits Adams Rite 8800 series. A. C. E. B. D. PD18-RIM Includes A. RIM

More information

PD15-UL-M KIT INSTRUCTIONS

PD15-UL-M KIT INSTRUCTIONS PD5-UL-M KIT INSTRUCTIONS The Command Access PD5-UL-M-KIT is a field-installable motorized latchpullback kit for the Jackson 85/95 & AHT 8/9 series devices. A. B. C. D. E. F. G. H. I. KIT INCLUDES TOOLS

More information

slp-ul-m KIT INSERT Instructions A. B. C. E. F. G.

slp-ul-m KIT INSERT Instructions A. B. C. E. F. G. slp-ul-m KIT INSERT Instructis The Command Access SLP-UL-M-KIT is a field installable motorized latch-pullback kit for the Sargent 80 series. A. B. C. D. E. E. F. G. A. B. C. D. E. F. Kit Includes 1- Motor

More information

LLP-UL-M-KIT Series Motorized Electric Latch Retraction

LLP-UL-M-KIT Series Motorized Electric Latch Retraction LLP-UL-M-KIT I n s ta l l at I o n InstructIons The LLP-UL-M-KIT is a field installable motorized latch pullback kit for the Hager 4500 and Lawrence 8000 series. B. C. A. D. LLP-UL-M-KIT IncLU d e s A.

More information

PD10-M-CVR INSTALLATION INSTRUCTIONS. Tools Required. PD10-M-CVR Includes

PD10-M-CVR INSTALLATION INSTRUCTIONS. Tools Required. PD10-M-CVR Includes PD10-M-CVR INSTALLATION INSTRUCTIONS The PD10-M-CVR is a storefront grade 1 exit device equipped with motor drive latch retraction. Retrofits Doromatic 1690 & First Choice 3690. C. I. D. E. F. G. H. PD10-M-CVR

More information

II E INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT

II E INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT II E1500-11 INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT KITS ARE UL LISTED UNDER CATEGORY GWVW, GWVW7 (CANADA) (ACCESSORY FOR USE ON FIRE EXIT HARDWARE AND PANIC HARDWARE). INDEX

More information

* * E996L Series. E996L for Rim/Vertical. E996L for Mortise CAUTION

* * E996L Series. E996L for Rim/Vertical. E996L for Mortise CAUTION *921297-00* 921297-00 Electric Locking Trim E996L Series Installation Instructions CAUTION Product is shipped in Fail Safe (FS) configuration. Fail Safe configuration is required by code in some applications

More information

INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT

INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT INSTALLATION INSTRUCTIONS MODEL 1550K-VD ELR FIELD INSTALLABLE KIT INDEX FUNCTION DESCRIPTION PAGE 1 PARTS LIST PAGE 2 TOOLS REQUIRED PAGE 2 KIT INSTALLATION INSTRUCTIONS PAGE 2-10 KIT ADJUSTMENT INSTRUCTIONS

More information

Electrical Options Booklet. Table of Contents

Electrical Options Booklet. Table of Contents *24228413* 24228413 Electrical Options Booklet Table of Contents EL Wiring... EL Troubleshooting... SD/EL 98/99 Cylinder Dogging... SS Wiring... 330, 350, RX-330 and RX-350 Push Bar Trim Mechanical Installation...

More information

Eaton Electronic Proportional (EP) Control for Medium Duty Piston Pumps

Eaton Electronic Proportional (EP) Control for Medium Duty Piston Pumps Eaton Electronic Proportional (EP) Control for Medium Duty 72400 Piston Pumps Table of Contents Introduction....................................................... 3 Identification of Components.........................................

More information

Electronic Proportional (EP) Control for Heavy Duty Series 0/1 Piston Pumps Model 33 Model 39 Model 46. Model 54 Model 64 Model 76

Electronic Proportional (EP) Control for Heavy Duty Series 0/1 Piston Pumps Model 33 Model 39 Model 46. Model 54 Model 64 Model 76 Electronic Proportional (EP) Control for Heavy Duty Series 0/1 Piston Pumps Model 33 Model 39 Model 46 Model 54 Model 64 Model 76 Table of Contents Introduction.......................................................

More information

*ININST.1039* 2390 Touchbar

*ININST.1039* 2390 Touchbar *ININST.1039* ININST.1039 Concealed Vertical Rod Panic Device 2390 Touchbar Installation Instructions Index Parts List... 2 Before Installation... 5 Installation... 5 RX Device Wiring... 12 EL Device Wiring...

More information

Electronic Proportional (EP) Control for Medium Duty Piston Pumps

Electronic Proportional (EP) Control for Medium Duty Piston Pumps Electronic Proportional (EP) Control for Medium Duty 72400 Piston Pumps EP Control for Medium Duty 72400 Piston Pumps Table of Contents Introduction........................................................................

More information

Electronic Proportional (EP) Control for Heavy Duty Series 2 Piston Pumps Model 33

Electronic Proportional (EP) Control for Heavy Duty Series 2 Piston Pumps Model 33 Electronic Proportional (EP) Control for Heavy Duty Series 2 Piston Pumps Model 33 Model 39 Model 46 Model 54 Model 64 EP Control for Heavy Duty Series 2 Piston Pumps Table of Contents Introduction........................................................................

More information

INSTALLATION INSTRUCTIONS CRL JACKSON 2085E

INSTALLATION INSTRUCTIONS CRL JACKSON 2085E INSTALLATION INSTRUCTIONS CRL JACKSON 2085E ELECTRIC LATCH RETRACTION CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com

More information

ARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI

ARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI II 1400-6 ARCHITECTURAL CONTROL SYSTEMS, INCORPORATED ST. LOUIS, MISSOURI ACSI 1426-04-AO ELECTRIC LATCH RETRACTION CONTROLLER INSTALLATION INSTRUCTIONS I.D. 1092, REV. C INSTALLATION For C-UL Listed applications,

More information

Plasma Display Electric Ceiling Lifts

Plasma Display Electric Ceiling Lifts I N S T R U C T I O N M A N U A L The Plasma Display Electric Ceiling Lift is designed for plasma displays requiring an extended drop (18 to 42 inches) from their hidden location. The lift is designed

More information

TS93 EMF T/PT/TDE. Surface applied door closer

TS93 EMF T/PT/TDE. Surface applied door closer TS9 EMF T/PT/TDE Surface applied door closer Installation instructions: Pull side track mount door closer (no smoke detector) (EMF T) Push side track mount closer (no smoke detector) (EMF PT) Double egress

More information

INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks

INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks Securitron Magnalock Corp. Tel 775.355.5625 550 Vista Boulevard Fax 775.355.5633 Sparks, NV 89434 info@securitron.com www.securitron.com ASSA ABLOY, the global leader in door opening solutions INSTALLATION

More information

55 Series Exit devices

55 Series Exit devices 55 Series Exit devices The Von Duprin 55 Series is a range of push bar exit devices designed to suit single and double door applications with narrow stiles. The 55 Series can be used on aluminium hollow

More information

KAWNEER 1686 EL CONCEALED EXIT DEVICE

KAWNEER 1686 EL CONCEALED EXIT DEVICE FEBRUARY, 2012 1 ROD AND CENTER CASE ASSEMBLY: 1) For inactive doors or doors without exterior cylinder, or doors without the need for exterior cylinder dogging, the removal of the cylinder dogging pawl

More information

HANDLING MECHANICAL INSTALLATION

HANDLING MECHANICAL INSTALLATION 2 INSTALLATION DESCRIPTION The and 2 Delay Egress Systems are 1500 pound holding force (holding force not evaluated by UL) per leaf electromagnetic locks, electronically controlled to provide a 15 or 30

More information

2904 Power Supply Installation Instructions I-EA00041

2904 Power Supply Installation Instructions I-EA00041 FEATURES Controls an opening with electrified locking device and automatic door operator Separate inputs for activation switch on entry and exit sides of opening Separate 24 VDC outputs for fail safe and

More information

Model 579 Curtain Machine Manual. General Information. Unpacking:

Model 579 Curtain Machine Manual. General Information. Unpacking: Model 579 Curtain Machine Manual. General Information The Model 579 curtain machine is designed for use with most light duty commercial and residential drapery tracks. The 579 curtain machine is designed

More information

Troubleshooting Guide: 255 LED Light

Troubleshooting Guide: 255 LED Light Troubleshooting Guide: 255 LED Light Note Use only factory replacement lights (refer to parts list for order number). Caution Carefully handle parts near membranes and wire harnesses. Allow the light to

More information

CONNECTOR AMPLIFIER FOR PROPORTIONAL VALVES (0-10VDC Input Version)

CONNECTOR AMPLIFIER FOR PROPORTIONAL VALVES (0-10VDC Input Version) TECHNICAL DATASHEET #TD1101AX CONNECTOR AMPLIFIER FOR PROPORTIONAL VALVES (0-10VDC Input Version) Part No.: CAPV-H-10V-x complete with cable CAPV-S7C-yM Where: x = current output (2A, 1.2A or 600MA) y

More information

POLARIS 4500 HD WINCH KIT

POLARIS 4500 HD WINCH KIT POLARIS 4500 HD WINCH KIT P/N 2883860 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain

More information

AL625 & AL625HD INSTALLATION & OWNER S MANUAL

AL625 & AL625HD INSTALLATION & OWNER S MANUAL AL625 & AL625HD INSTALLATION & OWNER S MANUAL These instructions are provided to assist you in the installation of the AL625. If you require further assistance, our trained staff is ready to provide you

More information

Notepad V-LT Universal Computer Mount will accomodate computers 8.2" to 11.8" in width, 7.58" to 9.3" in depth and up to 1.50" thick.

Notepad V-LT Universal Computer Mount will accomodate computers 8.2 to 11.8 in width, 7.58 to 9.3 in depth and up to 1.50 thick. INSTALLATION INSTRUCTIONS Product Revision Form Notepad V-LT Universal Cradle & Accessories Rev. A INST-562 7160-0402 Notepad V-LT Universal Cradle 7160-0251 Screen Support Assembly 7160-0252 LED Light

More information

Plasma Display Electric Pop-Up Lift (PUL)

Plasma Display Electric Pop-Up Lift (PUL) I N S T R U C T I O N M A N U A L Plasma Display Electric Pop-Up Lift (PUL) Your is designed for installation in furniture or cabinets. Display mounting is made easy using the Q-latch mounting system and

More information

SmartLock Accessories

SmartLock Accessories CANSEC ACCESSORIES SmartLock Accessories CA SLbox CA SLBOX SmartLock enclosure 9.5 x 13 x 3 metal enclosure with room for 1 or 2 SmartLock controllers, Cansec power supply and 12V 7 AH battery C Ca ps123a

More information

ETF-600 Sensor Operated Lavatory Faucet

ETF-600 Sensor Operated Lavatory Faucet INSTALLATION INSTRUCTIONS OPTIMA SYSTEMS SENSOR OPERATED LAVATORY FAUCET ETF-600 I.I. Code No. 0816318 ETF-600 Sensor Operated Lavatory Faucet Includes Instructions for Installation of Optional Back Checks

More information

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN SYMBOL LEGEND DANGER THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN WARNING THIS WARNS THAT MATERIALS MAY BE DAMAGED IF APPROPRIATE PRECAUTIONS ARE NOT

More information

Recessed. Touch bar exit devices

Recessed. Touch bar exit devices Recessed Touch bar exit devices Table of contents 3 2390 Concealed vertical rod device 4 Accessories 5 Power supply 6 Door application 7 How to order The Falcon difference Safety, security and uncompromising

More information

Model Railway Reverse Loops How to automate reversing tracks on your two-rail layout, whether DC, DCC or AC powered

Model Railway Reverse Loops How to automate reversing tracks on your two-rail layout, whether DC, DCC or AC powered Model Railway Reverse Loops How to automate reversing tracks on your two-rail layout, whether DC, DCC or AC powered Because of the way power is supplied to electric model trains, two-rail layouts require

More information

Master/Slave Actuators Spring Return Rotary 24 Vac - Modulating Control

Master/Slave Actuators Spring Return Rotary 24 Vac - Modulating Control Document No. 129-312 Master/Slave Actuators Spring Return Rotary 24 Vac - Modulating Control a PL0038R1 c b d e f g i Figure 1. Parts of the Master/Slave Actuators. h a. Actuator b. Shaft adapter c. Position

More information

ILD LOCK CYLINDER CHANGE-OUT INSTRUCTIONS REVISION 2_012505

ILD LOCK CYLINDER CHANGE-OUT INSTRUCTIONS REVISION 2_012505 1. TOOLS REQUIRED for ILD LOCK CYLINDER CHANGE-OUT a. 3/16 Hex Allen Wrench b. Phillips Screwdriver c. 1-3/8 Deep Socket or Adjustable Wrench d. Blocks to support ILD 2. LOCK CYLINDER ASSEMBLY REMOVAL,

More information

2007-UP NAVIGATION INTERFACE MODULE (Infiniti/Nissan)

2007-UP NAVIGATION INTERFACE MODULE (Infiniti/Nissan) 2007-UP NAVIGATION INTERFACE MODULE (Infiniti/Nissan) ALTHOUGH THIS PRODUCT HAS BEEN THOROUGHLY TESTED KPIERSON TECHNOLOGIES ASSUMES NO RESPONSIBILITY FOR ANY DAMAGE THAT MAY RESULT BY THE INSTALLATION

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Product Notepad V - Universal Cradle & Accessories Rev. F INST-479 7160-0250 Notepad V Universal Cradle 7160-0250-01 Notepad V Universal Cradle w/tall Side Clips 7160-0250-02

More information

INFINITY MULTA SERIES

INFINITY MULTA SERIES ASSEMBLY ASSEMBLY INSTRUCTIONS INSTRUCTIONS ASSEMBLY INSTRUCTIONS INFINITY MULTA SERIES Workstations, WORKSTATIONS, desks, DESKS, and AND tables TABLES with WITH powered POWERED ADJUSTMENT adjustment PARTS

More information

9700/F9700 SERIES RIM EXIT DEVICE

9700/F9700 SERIES RIM EXIT DEVICE INSTALLATION INSTRUCTIONS 9700/F9700 SERIES RIM EXIT DEVICE Index: Screw chart Tools required Outside trim options "03" Additional door prep Device installation Options available 5300 retro-fit preparation

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Dodge Ram 1500 Crew Cab 2009 - Current : 75138-15 Dodge Ram 2500/3500 & HD Crew Cab 2010 - Current : 75138-15

More information

Grout Pump Automatic & Manual Troubleshooting Gas Wiring Diagram

Grout Pump Automatic & Manual Troubleshooting Gas Wiring Diagram Grout Pump Automatic & Manual Troubleshooting 40-500 Gas Wiring Diagram Turn engine off and relieve hydraulic pressure and grout pressure before troubleshooting. Note: Typically there is a wiring diagram

More information

Model 2300JL Installation Guide

Model 2300JL Installation Guide Model 2300JL Installation Guide POWER ACCESS CORPORATION 4 HERSHEY DRIVE, DOCK 4 ANSONIA, CT 06401 800-344-0088 WEBSITE: www.power-access.com EMAIL: salesinfo@power-access.com 1 STANDARD PARTS MODEL 2300JL

More information

Model 2300DL Installation Guide

Model 2300DL Installation Guide Model 2300DL Installation Guide POWER ACCESS CORPORATION 4 HERSHEY DRIVE, DOCK 4 ANSONIA, CT 06401 800-344-0088 WEBSITE: www.power-access.com EMAIL: salesinfo@power-access.com 1 STANDARD PARTS MODEL 2300DL

More information

Quickie S-11 Service Manual

Quickie S-11 Service Manual Quickie S-11 Service Manual 05 Sunrise Medical Inc. 100740 Rev A Quickie S-11 Troubleshooting Guide INTRODUCTION... 0.1 Specifications VSI Controller... 0.2 Plugs/Connectors... 0.3 Main Wiring Diagram/

More information

Power Transfer Devices

Power Transfer Devices Security Door Controls 4 Power Transfer Devices From frame to door, SDC s power transfer devices provide secure, concealed or vandal-resistant means to transfer power and monitoring signals to doors equipped

More information

Flat Front Clip Clip Guide Lockable Latch Tee Nut Offset Front Clip

Flat Front Clip Clip Guide Lockable Latch Tee Nut Offset Front Clip INSTALLATION INSTRUCTIONS Product Revision Form Notepad V - Universal Cradle & Accessories Rev. D INST-479 7160-0250 Notepad V Universal Cradle 7160-0250-01 Notepad V Universal Cradle w/tall Side Clips

More information

ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS

ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS II 1400-10 ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS Features: Up to 1.95 Amps Load Capacity Class 2 Rated Outputs Overload, Over Voltage, and Short Circuit Protection Standby Battery

More information

56- Electric Latch Retraction Exit Devices Installation and Wiring Instructions

56- Electric Latch Retraction Exit Devices Installation and Wiring Instructions SECTION I: OVERVIEW 1. Description The Sargent 56- prefix ELR works with 80 Series exit devices to provide remote-controlled latch retraction. It is compatible with the following prefixes: 53 - Latchbolt

More information

(SB2) (SB1) (SB3) (SB5) (SB4) Cylindrical Installation Instructions. A. CHECKLIST (4 each AA Batteries Included) (SB1) (SB4) (SB2) (SB6) (SB6) (SB3)

(SB2) (SB1) (SB3) (SB5) (SB4) Cylindrical Installation Instructions. A. CHECKLIST (4 each AA Batteries Included) (SB1) (SB4) (SB2) (SB6) (SB6) (SB3) A. CHECKLIST (4 each AA Batteries Included) FOR DOOR AND FRAME PREPARATION INSTRUCTIONS, SEE APPENDIX A OR GO TO PROXESS.COM Parts List: Each Proxess C-Series lockset includes Exterior lock assembly (include

More information

Auto-Level Troubleshooting (Old Platform) Electronic Control- Prior to 2009, Pressure Switch Control panel #s 2057, 2058, 2795, 2795B

Auto-Level Troubleshooting (Old Platform) Electronic Control- Prior to 2009, Pressure Switch Control panel #s 2057, 2058, 2795, 2795B Auto-Level Troubleshooting (Old Platform) Electronic Control- Prior to 2009, Pressure Switch Control panel #s 2057, 2058, 2795, 2795B This guide addresses the troubleshooting of electronic controls used

More information

*ININST.1002* 1690 Touchbar. Index:

*ININST.1002* 1690 Touchbar. Index: *ININST.1002* ININST.1002 Concealed Vertical Rod Panic Device 1690 Touchbar Installation Instructions Index: : The door prep for the 1690 Hex Bottom Rod is different than for the RL bottom rod. Please

More information

Automatic Roof Hatch Opener

Automatic Roof Hatch Opener Automatic Roof Hatch Opener Installation Guide REQUIRED TOOLS (These tools are required to complete the installation) Cordless Drill 1/8 1/4 Drill Bits 1/8 Pin Punch #2 Philips Bit Rachet Sharpie Hammer

More information

ME AGS Auto Gen Start System for Coach Generators. Operator s Manual.

ME AGS Auto Gen Start System for Coach Generators. Operator s Manual. ME AGS Auto Gen Start System for Coach Generators Operator s Manual ME AGS Operator s Manual Auto Gen Start System for Coach Generators Section 2003 - Magnum Energy, Inc. Table of Contents Page 1. Overview

More information

Section 7 - Troubleshooting Guide

Section 7 - Troubleshooting Guide Section 7 - Troubleshooting Guide Section 7 - Troubleshooting Guide IMPORTANT While this troubleshooting guide provides information to aid in troubleshooting problems with the range, it does not contain

More information

Motorized Electric Latch Retraction

Motorized Electric Latch Retraction ; SECTION I: OVERVIEW 1. Description The Corbin Russwin MELR Electric Latch Retraction (ELR), refer to Figure 1, works with ED4000 & ED5000 Series exit devices to provide remote-controlled latch retraction

More information

ASSA ABLOY. 7100SZ Series SafeZone External Sensor. Installation and Instruction Manual ASSA ABLOY. Patent Pending

ASSA ABLOY. 7100SZ Series SafeZone External Sensor. Installation and Instruction Manual ASSA ABLOY. Patent Pending 700SZ Series SafeZone External Sensor Installation and Instruction Manual Patent Pending.76 (0). (79.8) Tools required:.0 (0.8) Allen wrench set (inch) Flat blade screwdriver (potentiometer & terminal

More information

SPEED SHIFT/TWO-STEP MODULE INSTALLATION MANUAL

SPEED SHIFT/TWO-STEP MODULE INSTALLATION MANUAL SPEED SHIFT/TWO-STEP MODULE INSTALLATION MANUAL ALTHOUGH THIS PRODUCT HAS BEEN THOROUGHLY TESTED KPIERSON TECHNOLOGIES ASSUMES NO RESPONSIBILITY FOR ANY DAMAGE THAT MAY RESULT BY THE INSTALLATION OF THIS

More information

USB Charge Port Installation Instructions

USB Charge Port Installation Instructions USB Charge Port Installation Instructions Lifetime Technical Support support@logolites.com 770-476-7322 www.logolites.com Manual 100-0014C Thank you for purchasing a Logo Lites USB Charge Port! USB Charge

More information

Shaved-B. Installation Manual & Operation Instructions

Shaved-B. Installation Manual & Operation Instructions Shaved-B Installation Manual & Operation Instructions Each Kit Contains The Following Components (1) Receiver (2) Remotes (2) Wire Harnesses Installation Instructions for SPAL Shaved Door Handle Kit Shaved-40

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL Rev. A, p. 1 of 13 INSTALLATION & OWNER S MANUAL Polaris Ranger (2009-) Straight UTV Steel Plow with Vehicle Mount Kit 6 Wide Snow Plow (p/n: 1POLSP) (fits the 500 H.O., 700 & 800 HD & XP) The contents

More information

COIL-OVER SUSPENSION SYSTEM

COIL-OVER SUSPENSION SYSTEM Page 1 of 11 PART NUMBER: 220.50.631X, 220.60.631X INSTRUCTION SHEET NUMBER: 920.65.9800A COIL-OVER SUSPENSION SYSTEM APPLICATION: 1997-2013 CORVETTE PACKAGE CONTENTS: Coil-Over Assembly - Front Right

More information

EQUALIZER SYSTEMS County Road 3 Elkhart, IN Fax

EQUALIZER SYSTEMS County Road 3 Elkhart, IN Fax EQUALIZER SYSTEMS 55169 County Road 3 Elkhart, IN 46515 800-846-9659 574-264-3437 Fax 574-266-6083 SERVICE INFORMATION FOR GULF STREAM COACH Many of the perceived problems with leveling and slide systems

More information

TRAC-Station BT Installation Instructions

TRAC-Station BT Installation Instructions TRAC-Station BT Installation Instructions P/N 10103024P1 November 2011 2011 UTC Fire & Security. All rights reserved. Introduction This is the Supra TRAC-Station BT Installation Instructions. Read these

More information

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN SYMBOL LEGEND DANGER THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN WARNING THIS WARNS THAT MATERIALS MAY BE DAMAGED IF APPROPRIATE PRECAUTIONS ARE NOT

More information

Conflicts: Vehicles with a sunroof

Conflicts: Vehicles with a sunroof Toyota 4Runner Non/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit -00110-15, Beige 00016-00120; Fit Kit -00120-15, Gray Accessory Code: ED6 Conflicts: Vehicles with a sunroof Kit Contents:

More information

Installation Instructions PowerBoard Automatic Retracting Running Board

Installation Instructions PowerBoard Automatic Retracting Running Board Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Dodge Ram Quad Cab Pickup 2002-2008 : 75101-15 Dodge Ram Quad Cab Pickup, 2500 / 3500 / HD 2003-2009 : 75101-15

More information

[ ]

[  ] [ www.pigpopper.com ] Installation Guide Pig Popper Installation Guide Enduro Pipeline Services, Inc. P.O. Box 489 Tulsa, OK 740 500 S. 45th W. Ave. Tulsa, OK 7407 p: (98) 446-94 toll-free: (800) 75-68

More information

Conflicts: Vehicles without a sunroof Vehicles with a single sunroof

Conflicts: Vehicles without a sunroof Vehicles with a single sunroof Toyota Sienna (Dual Sunroof) 2011-10.2 Overhead Video Part Number: 00016-00110 00016-00110-17 Fit Kit 00016-00120 00016-00120-17 Fit Kit Accessory Code: ED5 Conflicts: Vehicles without a sunroof Vehicles

More information

Dodge Engineering & Controls, Inc. Toll Free (877) Fax: (978) EN44 and EN88 Non-Spring Return Electronic Actuators

Dodge Engineering & Controls, Inc. Toll Free (877) Fax: (978) EN44 and EN88 Non-Spring Return Electronic Actuators Dodge Engineering & Controls, Inc. EA678R3 45 a b e d c a. Actuator b. Position indicator c. Mounting bracket (for dampers) d. Mounting screws e. 4 mm hex wrench Figure 1. Parts of the EN44 and EN88 Actuators.

More information

CV41. Vehicle Mounting Kit. Reference Guide

CV41. Vehicle Mounting Kit. Reference Guide CV41 Vehicle Mounting Kit Reference Guide CV41 Vehicle Mounting Kit Reference Guide........... 3 Secure the Smart Dock to a Vehicle.................... 3 Supply Power to the Smart Dock......................

More information

4500 Series Electric Exit Devices Request to Exit (RX) Installation Instruction Grade 1 I-ED00368

4500 Series Electric Exit Devices Request to Exit (RX) Installation Instruction Grade 1 I-ED00368 4500 Series Electric Exit Devices Request to Exit (RX) Installation Instruction Grade 1 I-ED00368 DEVICES COVERED IN THESE INSTRUCTIONS: RX Request to Exit ELECTRICAL SPECIFICATIONS Note: SPDT mechanical

More information

Recessed. Exit Device Series

Recessed. Exit Device Series Recessed Exit Device - 2390 Series Table of Contents 2390 Concealed Vertical Rod Device 3 Accessories 4 Power Supply 5 Door Application 6 How To Order 7 F A L C O N E X I T D E V I C E S Architectural

More information

Vehicle Security System

Vehicle Security System Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

INSTALLATION & USER S GUIDE

INSTALLATION & USER S GUIDE REKLUSE MOTOR SPORTS The Rekluse Core EXP Kit for Kawasaki KX80/85/100 OVERVIEW INSTALLATION & USER S GUIDE Doc ID: 191-7742A Doc Rev: 073015 This kit replaces the OEM core clutch components including

More information

Installation Instructions Table of Contents

Installation Instructions Table of Contents Installation Instructions Table of Contents Pre- Installation of Garage Storage Lift 2 Layout the Garage Storage Lift 3 Installing the strut Channels 3 Install the Drive Assembly 5 Install the Drive Shaft

More information

INSTALLATION GUIDE Car Show Dual DVD Headrest Replacement System

INSTALLATION GUIDE Car Show Dual DVD Headrest Replacement System INSTALLATION GUIDE Car Show Dual DVD Headrest Replacement System NOTICE OF INTENDED INSTALLATION AND USE CAR SHOW VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER, AND ARE TO BE INSTALLED ONLY

More information

PROVEX Installation Guide. Version 1.0

PROVEX Installation Guide. Version 1.0 Version 1.0 INTRODUCTION The scale must not be loaded beyond its capacity. Do not select a site where overweight load would have to maneuver to avoid crossing the platform. Avoid areas where the scale

More information

INSTALLATION GUIDE. AV8900H Dual Multimedia Headrest Replacement System

INSTALLATION GUIDE. AV8900H Dual Multimedia Headrest Replacement System INSTALLATION GUIDE AV8900H Dual Multimedia Headrest Replacement System NOTICE OF INTENDED INSTALLATION AND USE AV8900H VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER, AND ARE TO BE INSTALLED

More information

SD Bendix E-10PR Retarder Control Brake Valve DESCRIPTION. OPERATION - Refer to Figure 2

SD Bendix E-10PR Retarder Control Brake Valve DESCRIPTION. OPERATION - Refer to Figure 2 SD-03-832 Bendix E-10PR Retarder Control Brake Valve MOUNTING PLATE SUPPLY 4 PORTS ELECTRICAL AUXILIARY DESCRIPTION TREADLE RETARDER CONTROL SECTION EXHAUST DELIVERY 4 PORTS FIGURE 1 - E-10PR RETARDER

More information

Toyota 4RUNNER With/MR Overhead Video

Toyota 4RUNNER With/MR Overhead Video Toyota 4RUNNER With/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit-00110-14, Beige 00016-00120; Fit Kit-00120-14, Gray Accessory Code: ED7 Conflicts: Vehicles without a sunroof Kit Contents:

More information

Model PRO 9644a Installation Manual

Model PRO 9644a Installation Manual Model PRO 9644a Installation Manual SELECTABLE FEATURES Note: The method of manual override can either be selected to operate from the valet switch operate as custom code. Be certain to place a check mark

More information

VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate

VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate 3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate (Refer to qualified

More information

Tusk UTV Horn & Signal Kit Installation Instructions

Tusk UTV Horn & Signal Kit Installation Instructions Tusk UTV Horn & Signal Kit Installation Instructions The Tusk UTV signal kit is designed to be a simple way to provide front and rear turn signals, license plate mount with light, horn, and rearview mirrors

More information

Adams rite. Exit Devices & parts exit devices series exit device parts

Adams rite. Exit Devices & parts exit devices series exit device parts Adams rite Exit Devices & parts exit devices 8099 8211 8099 Active Dummy Bar with Switch Can be wired normally open or normally closed to operate maglock, alarm, etc No latching mechanism 8211 Surface

More information

Upgrade v3 to v3.2. SeeMeCNC Guides. Upgrade v3 to v3.2. Rostock Max v3 Uprgade to v3.2. Written By: SeeMeCNC seemecnc.dozuki.

Upgrade v3 to v3.2. SeeMeCNC Guides. Upgrade v3 to v3.2. Rostock Max v3 Uprgade to v3.2. Written By: SeeMeCNC seemecnc.dozuki. SeeMeCNC Guides Upgrade v3 to v3.2 Rostock Max v3 Uprgade to v3.2 Written By: SeeMeCNC 2018 seemecnc.dozuki.com/ Page 1 of 34 INTRODUCTION This guide is intended to Upgrade a Rostock Max v3 to a Rostock

More information

LI-ION BATTERY UPFIT KIT

LI-ION BATTERY UPFIT KIT LI-ION BATTERY UPFIT KIT P/N 2881852 APPLICATION E2, E4, E6, and el XD BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 9002-6513 Rear Vision System W/ Zoom Aftermarket and Factory 8.4 Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 2012 RAM (Part B) 2013 Current RAM (Part A) NOTE:

More information

User Instructions for WRC1021D. Doc

User Instructions for WRC1021D. Doc User Instructions for WRC1021D Doc. 0001-5989 CONTENTS 1.0 INTRODUCTION TO THE WRC1021D... 2 2.0 FUNCTIONAL DESCRIPTION... 3 3.0 POTENTIOMETERS, SWITCHES AND INDICATORS... 5 4.0 CALIBRATION AND START-UP

More information

Fitting Instructions. Armlock 1354 Mini Electro-Shearmagnet (Surface) Contents

Fitting Instructions. Armlock 1354 Mini Electro-Shearmagnet (Surface) Contents Fitting Instructions Armlock 1354 Mini Electro-Shearmagnet (Surface) Contents Before You Start...page 1 Installation instructions for wood, aluminium and glass...page 2 Wiring Diagram...page 3 Wiring and

More information

Coil Inserter Module

Coil Inserter Module Coil Inserter Module 1) Installation Instructions: Diagram 4 Procedure to attach the coil inserter onto the OD 4012 punch Unplug the main power cord from the OD 4012. Remove the two safety screws (3/32

More information

INSTALLATION INSTRUCTIONS CRL ESK2/ESP2

INSTALLATION INSTRUCTIONS CRL ESK2/ESP2 INSTALLATION INSTRUCTIONS CRL ESK2/ESP2 ELECTRIC STRIKE KEEPER FOR DOUBLE DOORS NOTE: Sensor feature available on ESP s only. ALUMINUM Phone: (800) 421-6144 Fax: (800) 587-7501 crlaurence.com usalum.com

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 144F TABLE OF CONTENTS GENERAL... 2 SPECIFICATIONS... 2 PACKAGE CONTENTS... 2 PACKAGE CONTENTS: ACCESSORIES... 3 REQUIRED TOOLS... 3 ADD-ON COMPONENTS... 3 CABINET MOUNTING WALL MOUNT BRACKET ATTACHMENT...

More information

1.0 Features and Description

1.0 Features and Description 1.0 Features and Description The is an intelligent actuator designed for precise control of quarter turn valves and dampers. Using stepper motor technology, the SmartStep proportionally positions valves

More information

D4BL. Protective Doors Are Locked Until Machines Completely Stop Operating. Guard Lock Safety-door Switch. Model Number Structure.

D4BL. Protective Doors Are Locked Until Machines Completely Stop Operating. Guard Lock Safety-door Switch. Model Number Structure. Guard Lock Safety-door Switch Protective Doors Are Locked Until Machines Completely Stop Operating A mechanical lock is applied automatically when the Operation Key is inserted. A high level of safety

More information

INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER

INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER Form 5063T, 06-05 Supersedes Form 5063T, 02-04 INSTALLATION INSTRUCTIONS FOR DSP9600/9100 WHEEL BALANCER This document provides the information needed to install the DSP9600/9100 Wheel Balancer. NOTE:

More information