Remote activation of visibility and lighting functions

Size: px

Start display at page:

Download "Remote activation of visibility and lighting functions"

Lester Richardson
5 years ago
Views:

1 Function Function The following visibility and lighting functions can be activated remotely: More information on lighting is found in the Deactivation of the driving light and Alternating main beam flashing documents. Hazard warning signal Main beam Work light External lighting device check Horn Windscreen wipers Behaviour Hazard warning signal All direction indicator lamps flash. The function can be configured as follows: The EXT switch must be pressed before activation. The hazard warning signal flashes the whole time when activated. When the function is activated, the hazard warning signal is switched off automatically when the vehicle moves and switched on automatically when the vehicle is stationary. Main beam Main beam comes on. The function can be configured as follows: The spotlights come on together with the main beam. The EXT switch must be pressed before activation. 22: Issue 2.1 en-gb 1 (10)

2 Behaviour When the function is activated, the main beam is switched off automatically when the vehicle moves and switched on automatically when the vehicle is stationary. Work light Activates work light. Remote activation of the work light can be done via BIC (Bodywork Interface configuration) or External CAN. When activation is not requested any longer the work light is switched off. If the work light is activated via a switch it can be deactivated by another signal via BIC or via External CAN. If activation and deactivation is requested at the same time from BIC, the work light will come on automatically when the vehicle is stationary and go off automatically when the vehicle moves. If the speed exceeds a preset value, the function will be deactivated irrespective of what the BCI control unit requests. The speed limit can be set by a parameter. External lighting and reverse alarm check Switches on the external lighting devices in sequence so that the driver can check that the lighting and reverse alarm are working. The function is activated and deactivated by sending a second pulse to the selected input. 22: Issue 2.1 en-gb 2 (10)

3 Behaviour Horn Activates the horn. The function can be configured as follows: The EXT switch must be pressed before activation. When the function is activated, the horn is switched off automatically when the vehicle moves and switched on automatically when the vehicle is stationary. Windscreen wipers Activates the windscreen wipers. The function can be configured as follows: The windscreen wipers operate at high or low speed The EXT switch must be pressed before activation. When the function is activated, the windscreen wipers are switched off automatically when the vehicle moves and switched on automatically when the vehicle is stationary. 22: Issue 2.1 en-gb 3 (10)

4 Behaviour Activation The following conditions must be fulfilled at activation of the different functions: List of conditions: 1. Starter key in drive position 2. EXT switch activated 3. Stationary 4. Parking brake applied Function Compulsory Possible conditions Hazard warning signal 1 2 and 3 Main beam 1 2 and 3 Work light 1 External lighting check 1 and 4 Horn 1 2 and 3 Windscreen wipers 1 2 and 3 If these conditions are fulfilled, the function can be activated via BIC (Bodywork Interface Configuration) and External CAN. With or without EXT switch (sequential check) With EXT switch: The EXT switch must be activated after the starter key has been turned to the drive position. Only then, the selected function can be activated. Without EXT switch: Activation of the function has no dependency on the EXT switch. 22: Issue 2.1 en-gb 4 (10)

5 Chassis conditions Chassis conditions Vehicle production period Preparations from the factory Production site Chassis serial number Option Alternative Variant code BCI functionality With 5837A Södertälje Zwolle If required Angers Bodywork cable harness from cab to frame pin 2411F Bodywork cable harness in frame 2 m 3023A São Bernardo do Campo m 3023D 12 m 3023C 22: Issue 2.1 en-gb 5 (10)

6 Chassis conditions Parameters that can be adjusted using SDP3 If there is no access to SDP3, contact a Scania dealer. The parameters are adjusted under functions in SDP3. Parameter Explanation Possible value From factory Group EXT switch a Controls whether the EXT switch should Without Spring-loaded Bodywork adaptation be active or not 2 positions Spring-loaded Spotlight control Setting for how the spotlights are to be lit. Alternative 1: The spotlights are to be switched on Alternative 1 either in the sun visor or in the bumper, but never at the same time. Spotlights at remote main beam activation Work light together with reversing light Switching off the work light at a certain speed Windscreen wipers, speed at remote activation Vehicle speed conditions for remote control of functions in the visibility system Spotlights should be activated at remote main beam activation. Setting to use the work light together with reversing light. Setting of the work light to go out automatically when the vehicle exceeds a certain speed. Select the speed of the windscreen wipers at remote activation. Here you set how the possibility of remote control of the visibility system functions is to depend on the vehicle s speed. a. The parameter setting affects all functions that are dependent on the EXT switch. Alternative 2: The spotlights are switched on both in the sun visor and the bumper. With Without With Without Without With 8 91 km/h 20 km/h Low speed High speed While moving Stationary Low speed Stationary Visibility More information on the parameters is found under Adjustable parameters. 22: Issue 2.1 en-gb 6 (10)

7 Signal type and activation of function Signal type and activation of function Example of activation of the function Type of activation BIC (Bodywork Interface Configuration) External CAN Activation method Via pin in C259 or another signal in BIC. Bodywork Visibility Control: Hazard Lamp Request Bodywork Visibility Control: Main Beam Request Bodywork Visibility Control: Work Light Control Bodywork Visibility Control: Horn Request Bodywork Visibility Control: Wiper Activation 22: Issue 2.1 en-gb 7 (10)

8 Signal type and activation of function Example of connection using BICT, +24 V and ground V 2 This description shows a connection inside the cab. Information on how to make the connection with an extension harness on the chassis is found in the document Cable harness cab and frame (22:10-080). 3 1 Proceed as follows: 1. Connect the activation cable to any input pin in connector C Using BICT (Bodywork Interface Configuration Tool), the function is allocated to the selected pin. C259 C The function is ready for activation. Part information and connection positions 1 For example, a switch Connected to any pin on C259 Activation by +24 V Fuse 5 A Fitted by bodybuilder 3 Cable Cable cross-section min mm² Fitted by bodybuilder The parts can be purchased from a Scania dealer C259 C Activation by grounding 22: Issue 2.1 en-gb 8 (10)

9 Signal type and activation of function Signal type Pin (BWE) Activation method +24 V to selected pin on C259 BCI master C-pin (1 10), High or low Selected function or Grounding of selected pin on C In BICT The pin selected to activate the function 2. Function: Remote activation of selected function 22: Issue 2.1 en-gb 9 (10)

10 Signal type and activation of function Connection via External CAN This description shows a connection inside the cab. Information on how to make the connection with an extension harness on the chassis is found in the document Cable harness cab and frame (22:10-080). To be able to make a connection via External CAN, the following is required: The vehicle is equipped with BCI functionality variant code 5837A C493 The parameter for External CAN is activated The connection is made directly to connector C493 (External CAN-low to pin 3 and External CAN-high to pin 4). C Signal type CAN Message Bodywork Visibility Control: Hazard Lamp Request Activation via External CAN Bodywork Visibility Control: Main Beam Request Bodywork Visibility Control: Work Light Control Bodywork Visibility Control: Horn Request Bodywork Visibility Control: Wiper Activation The parts can be purchased from a Scania dealer. More information on CAN can be found in the CAN documents under Electrical systems. 22: Issue 2.1 en-gb 10 (10)

Remote engine start. Function. Behaviour. The remote engine start function is used to start the engine from outside the cab.

Remote engine start. Function. Behaviour. The remote engine start function is used to start the engine from outside the cab. Function Function The remote engine start function is used to start the engine from outside the cab. Behaviour The direction indicators are used to provide a visual acknowledgement as to whether the attempt