TOYOTA TACOMA TVIP V3 (RS3200) Section I - Installation Preparation
|
|
- Tabitha Griffith
- 6 years ago
- Views:
Transcription
1 Section I - Installation Preparation Part Number: Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Status Monitor 3 1 Piezo Buzzer 4 1 Butyl Tape Pad 5 1 Extra Lage Wire Tie Hardware Bag Contents Item # Quantity Reqd. Description 1 2 Large Foam Tape Strip (2 pcs.) 2 3 Small Foam Tape Strip 3 5 Large Wire Ties 4 10 Medium Wire Ties Color Applicability/ Trim Level Accessory Color Vehicle/Trim Color Additional Items Required Installation Item # Quantity Reqd. Description 1 1 V3 Base Kit ( ) Conflicts Note: Recommended Tools Safety Tools Safety Glasses Safety Gloves Vehicle Protection Special Tools Striker Tool Installation Tools Phillips Head Screwdriver Flat Blade Screwdriver 10 mm Socket Pneumatic/Electric Wrench Torque Wrench Nylon Panel Removal Tool Side Cutters (Optional) Blankets, Part Boxes ALL #2, screwdriver or tip Small General Applicability Tacoma with power door locks, only Recommended Sequence of Application Item # Accessory 1 Audio 2 V3 Legend STOP *Mandatory STOP : Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY : Use caution to avoid risk of injury. CRITICAL PROCESS : Proceed with caution to ensure a quality installation. These points will be audited on a completed vehicle installation. GENERAL PROCESS : This highlights specific processes to ensure a quality installation. These points will be audited during the accessory installation. TOOLS & EQUIPMENT : This calls out the specific tools and equipment required for this process. Special Chemicals 3M Prep Solvent-70 Page 1 of 28 Pages
2 A. Vehicle Disassembly 1. Disconnect the negative battery cable. (Fig. A1) i. Cover the fender before starting. 10 mm Wrench Battery Negative Battery Cable Be careful not to touch the positive battery cable. Fig. A1 2. Remove the driver side step cover. (Fig. A2) i. Protect the seat and floor before starting. Nylon Panel Removal Tool Phillips Screwdriver Screw (x4) Remove the four screws securing the cover. Step Cover i Do not scratch the cover. Fig. A2 Nylon Panel Removal Tool 3. Remove the driver side cowl cover. (Fig. A3) i. Do not scratch the cover. 4. Remove the hood release lever. (Fig. A4) i. Remove the two screws securing the lever to the lower dash cover. Remove the cable from the lever. 5. Remove the lower dash cover. (Fig. A4) Phillips Screwdriver, 10mm Socket Screw Cowl Cover Bolt (x3) Fig. A3 i. Remove the four bolts and one screw securing the cover. Lower Dash Cover Bolt Do not scratch the cover. Screw (x2) Fig. A4 Page 2 of 28 Pages
3 6. Prepare a blanket, then place the blanket over the front edge of the center console. (Fig. A5) Protective Sheet Fig. A5 7. Loosen the bracket cover, but do not remove the cover. (Fig A6) i. Remove the two clips securing the bracket cover. Do not scratch the cover. i Do not bend the cover. Clip Bracket Cover Clip Fig. A6 B. Piezo Buzzer Installation 1. Remove and save the three bolts securing R/B No. 2 to the body in the engine room. (Fig. B1) 10 mm Socket, Socket Extension R/B No. 2 Bolt (Existing) Bolt (Existing) Fig. B1 2. Locate the vehicle harness gray 2P connector, then remove and discard the black cap. (Fig. B2) i. Locate the 2P connector between the R/B No.2 and the body. Pull the connector toward the battery to remove the cap and make the connection. Battery Cap (Remove) Vehicle Harness 2P (Gray) Fig. B2 Page 3 of 28 Pages
4 3. Plug in the Piezo Buzzer s gray 2P connector into the vehicle harness' gray 2P connector. (Fig. B3) 4. Secure the Piezo Buzzer to the vehicle s harness with one large strip of foam tape, then secure the Piezo Buzzer to the vehicle s harness with one large wire tie. (Fig. B3) i. Do not cover the opening of the Buzzer with the foam tape. Clip the wire tie. Side Cutter Large Wire Tie Vehicle Harness 2P (Gray) Piezo Buzzer s 2P (Gray) Large Foam Tape Fig. B3 Side Cutter 5. Bundle the extra length of the Piezo Buzzer s harness to the vehicle s harness with one large wire tie. (Fig. B4) i. Clip the wire tie. Large Wire Tie Piezo Buzzer s Harness Piezo Buzzer Fig. B4 C. V3 Harness Installation 1. Locate and disconnect the white 12P connector from the driver s side cowl area. (Fig. C1) i. Do not pull on the wires; pull on the connector. Vehicle Harness 12P (White) Fig. C1 Page 4 of 28 Pages
5 2. Plug in the V3 harness white 12P connector into the vehicle s white 12P connector and the driver s side connector block. (Fig. C2) Vehicle Harness 12P (White) V3 Harness 12P (White) V3 Harness 12P (White) Fig. C2 3. Wrap the white 12P connectors with one large strip of foam tape. (Fig. C3) Large Foam Tape Vehicle Harness 12P (White) V3 Harness 12P (White) Fig. C3 D. ECU Preparation and Installation 1. Turn the adjustment screw on the V3 ECU to the "5" position. (Fig. D1) Small Flat Blade Screwdriver V3 ECU GBS Setting Fig. D1 Page 5 of 28 Pages
6 2. Plug in the V3 harness ECU connectors to the V3 ECU. (Fig. D2) EXAMPLE V3 ECU V3 ECU Connectors (8P, 12P, 22P) Fig. D2 3. Using 3M Prep Solvent -70, clean the area indicated on the driver s side cowl area. (Fig. D3) 4. Remove the backing sheet, and attach the butyl tape near the driver side cowl area as shown. (Fig D3) i. Do not touch the adhesive surface of the butyl tape. Butyl Tape Fig. D3 5. Remove the backing sheet, and attach the V3 ECU as shown. (Fig. D4) i. Do not touch the adhesive surface of the butyl tape. Press the V3 ECU to the driver side cowl area firmly. V3 ECU Page 6 of 28 Pages Fig. D4
7 6. Secure the V3 ECU to the driver s side cowl area with one extra large wire tie as shown. (Fig. D5) i. Clip the wire tie. Side Cutter Extra Large Wire Tie V3 Harness V3 ECU V3 Harness 6P (White) Fig. D5 7. Attach two large foam tapes to the surface of the V3 ECU. (Fig. D6) V3 ECU Large Foam Tape (x2) Fig. D6 E. V3 Harness Installation (Continued) 1. Place the white 12P connector into the hole of driver side connector block area. (Fig. E1) 12P Connector Fig. E1 Page 7 of 28 Pages
8 2. Locate the white 6P connector from the driver side cowl area. (Fig. E2) V3 ECU 3. Plug in the V3 harness white 6P connector into the vehicle s 6P connector. (Fig. E2) V3 Harness Vehicle Harness 6P (White) V3 Harness 6P (White) Fig. E2 4. Wrap the white 6P connector with one small strip of foam tape. (Fig. E3) V3 Harness 6P Small Foam Tape Fig. E3 5. Route the V3 harness up toward the Instrument Panel J/B, then secure it to the vehicle s harness with two medium wire ties. (Fig E4) i. Clip the wire ties. Side Cutter V3 Harness Medium Wire Tie (x2) V3 ECU Fig. E4 Page 8 of 28 Pages
9 6. Locate and disconnect the white 22P connector from the Instrument Panel J/B. (Fig. E5) Instrument Panel J/B i. Do not pull on the wires; pull on the connector. Vehicle Harness 22P (White) Fig. E5 7. Plug in the V3 harness white 22P connector between the vehicle harness white 22P connector and the Instrument Panel J/B. (Fig. E6) Instrument Panel J/B V3 Harness 22P (White) Vehicle Harness 22P (White) V3 Harness V3 Harness 22P (White) Fig. E6 8. Secure the V3 harness to the Instrument Panel J/B with one large wire tie. (Fig. E7) i. Clip the wire tie. Side Cutter Instrument Panel J/B Large Wire Tie 22P Page 9 of 28 Pages V3 Harness Fig. E7
10 9. Attach the 22P connectors and the V3 harness to the Instrument Panel J/B with one small strip of foam tape. (Fig. E8) Instrument Panel J/B Small Foam Tape V3 Harness Fig. E8 10. Locate and disconnect the white 9P connector from the back side of Instrument Panel J/B. (Fig. E9) i. Do not pull on the wires; pull on the connector. Vehicle Harness 9P (White) Back side view of Instrument Panel J/B Instrument Panel J/B 9P (White) Fig. E9 11. Plug in the V3 harness white 9P connector between the vehicle harness white 9P connector from the back side of the Instrument Panel J/B. (Fig. E10) Instrument Panel J/B 9P V3 Harness 9P Fig. E10 Page 10 of 28 Pages
11 12. Route the V3 harness up toward the Instrument Panel J/B area, then secure the white 9P connector to the vehicle harness with one large wire tie. (Fig. E11) Side Cutter Instrument Panel J/B V3 Harness i. Clip the wire tie. 9P 9P Large Wire Tie Fig. E Route the V3 harness behind the heater duct, to the Instrument Panel J/B and steering column area, then secure it to the vehicle harness with one medium wire tie. (Fig. E12) i. Clip the wire tie. Side Cutter V3 Harness 3P (Gray) Medium Wire Tie V3 Harness V3 Harness 4P (White) V3 Harness 8P (White) Fig. E Locate and disconnect the gray 3P connector from near the back side of the Instrument Panel J/B. (Fig. E13) i. Do not pull on the wires; pull on the connector. Vehicle Harness 3P (Gray) Instrument Panel J/B Fig. E13 Page 11 of 28 Pages
12 15. Plug in the V3 harness gray 3P connectors into the vehicle s gray 3P connectors. (Fig. E14) V3 Harness 3P (Gray) Vehicle Harness 3P (Gray) Instrument Panel J/B V3 Harness 3P (Gray) Fig. E Locate and disconnect the white 8P connector from the ignition switch. (Fig. E15) Key Cylinder i. Do not pull on the wires; pull on the connector. Vehicle Harness 8P (White) Fig. E Plug in the V3 harness white 8P connector between the vehicle harness white 8P connector and ignition switch. (Fig. E16) V3 Harness 8P (White) Vehicle Harness 8P (White) V3 Harness Fig. E16 Page 12 of 28 Pages
13 18. Secure the V3 harness to the vehicle harness with one medium wire tie. (Fig. E17) i. Clip the wire tie. 19. Secure the V3 harness with the existing clip. (Fig. E17) Side Cutter Medium Wire Tie Existing Clip 8P V3 Harness Fig. E Secure the V3 harness fuse and V3 harness to the vehicle harness with one medium wire tie. (Fig. E18) i. Clip the wire tie. Side Cutter 8P 8P V3 Harness Vehicle Harness Fuse Medium Wire Tie Fig. E Route the V3 harness toward the center console area, then secure it to the vehicle harness with one medium wire tie. (Fig. E19) i. Clip the wire tie. Side Cutter V3 Harness V3 Harness 4P (White) Medium Wire Tie Fig. E19 Page 13 of 28 Pages
14 F. Status Monitor Installation 1. Remove and discard the knockout cover from the bracket cover. (Fig. F1) i. Do not scratch the cover. TOYOTA Do not bend the cover. 2. Install Status Monitor to the bracket cover. (Fig. F1) i. Do not scratch the cover. Bracket Cover Status Monitor Fig. F1 3. Plug in the V3 harness white 4P connector to the Status Monitor s white 4P connector. (Fig. F2) Bracket Cover Small Foam Tape V3 Harness 4P (White) 4. Wrap the white 4P connectors with one small strip of foam tape. (Fig. F2) Status Monitor Status Monitor s 4P (White) Protective Sheet Fig. F2 G. Warning Label Installation 1. Clean the inside surface of the front door windows. (Fig. G1) 2. Place the warning label on the inside surface of the front door window as shown. (Fig. G1) i. Use a piece of clear adhesive tape to lift the labels off of their protective backing sheet. Warning Label 10mm Do not touch the adhesive surface of the warning labels. Fig. G1 Page 14 of 28 Pages
15 H. Completing the Installation 1. Complete the reassembly of the vehicle. i. Reconnect any disconnected connectors. Verify the panels fit together properly with no uneven gaps between them. 2. Clean up and remove any trash. 3. Reconnect the vehicle's negative battery cable. (Fig. H1) i. Position the negative battery terminal at an angle of 45 to the battery as shown. Torque Wrench, 10mm Socket Battery 45 Negative Battery Cable Fig. H1 Tighten the nut with 3 ft lbs of torque. i Be careful to not touch the positive battery terminal. 4. Leave the owner s manual, warranty card, and remote controls in their protective bags and place in the glove box. Page 15 of 28 Pages
16 Section III - Functional Verifications Section III - Functional Verifications Check: Look for: Accessory Function Checks Press and release the remote control s lock button to start the system s arming process. Wait 30 seconds. Press and release the remote control s unlock button to disarm the system. Press and release the remote control s unlock button again within 3 seconds of disarming the system. Open and close the driver's door. Arm and disarm the system with the remote again, then wait thirty seconds. Press and release the remote control's unlock button again to stop the arming process. Open the driver's door, then press and release the remote control's lock button. Close the driver's door. Press and release the remote control's panic button to trigger the panic alarm. Press and release the remote control's panic button again to stop the panic alarm The tail and marker lights flash once. The buzzer chirps once. All doors lock. The LED lights up. After 30 seconds, the LED starts flashing; the system is now armed. The tail and marker lights flash twice. The buzzer chirps twice. The interior lights turn on for thirty seconds. The driver's door unlocks. The LED stops flashing. The tail and marker lights flash twice. The buzzer chirps twice. All remaining doors unlock. The doors automatically relock. The system automatically starts the arming process. Refer to step #3. The buzzer sounds continuously for 5 seconds. The buzzer stops sounding. The horn sounds repeatedly. The interior lights turn on. The headlights flash repeatedly. The tail and marker lights flash repeatedly. The LED lights up. The horn stops sounding. All the lights stop flashing and/or turn off. Page 16 of 28 Pages
17 Section III - Functional Verifications Section III - Functional Verifications Check: Look For: Sit in the driver's seat and make sure all doors are closed. Insert the key into the ignition switch and turn it to "ON". Roll down all the windows. Turn the key back to "LOCK". Remove the key and exit the vehicle. Insert the key into the driver's door key cylinder and turn it toward the front of the vehicle to start the arming process. Wait 30 seconds. Reach inside and manually unlock the driver's door to trigger an alarm. Manually unlock the driver's door again and hold it unlocked, open the door, then sit in the driver's seat. Insert the key into the ignition switch and turn it to "START" to stop the alarm. Turn the key back to "LOCK", remove it, then exit the vehicle All doors lock. All doors unlock. All doors lock. The LED lights up. After 30 seconds, the LED starts flashing; the system is now armed. The driver's door automatically relocks. The horn sounds repeatedly. The interior lights turn on. The headlights flash repeatedly. The tail and marker lights flash repeatedly. The LED lights up. The driver's door lock attempts to lock repeatedly. The horn continues to sound repeatedly. The interior lights remain on. The headlights, tail lights and marker lights continue flashing. The LED remains on. The horn stops sounding. All the lights stop flashing and/or turn off. The LED turns off. The starter cranks and the engine starts. Page 17 of 28 Pages
18 Section III - Functional Verifications Section III - Functional Verifications Check: With the door open, press the lock switch on the door to lock the doors, then close the door to start the system's arming process. Wait 30 seconds. Reach inside and manually unlock the front passenger's door to trigger an alarm. Press and release the remote control's unlock button to stop the alarm. Press and release the remote control's lock button to start the system's arming process. For D-Cab "only", climb into the rear passenger area, then close the door. Press and release the remote control's lock button to start the system's arming process, then wait 30 seconds until the system is armed. Unlock and open one of the rear passenger doors to trigger an alarm. Repeat the above steps with the other rear passenger door (if equipped.) Look For: Tail and maker lights flash once. The buzzer chirps once. All doors lock. The LED lights up. After 30 seconds, the LED starts flashing; the system is now armed. The front passenger's door automatically relocks. The horn sounds repeatedly. The interior lights turn on. The headlights flash repeatedly. The tail and marker lights flash repeatedly. The LED lights up. The horn stops sounding All lights stop flashing and/or turn off. The LED turns off. Refer to step #18. Same as step #1 and #2. Refer to #9. Refer to step #23 and #24. Roll up all windows, remove the key and exit the vehicle. Page 18 of 28 Pages
19 Section III - Functional Verifications Section III - Functional Verifications Check: Press and release the remote control's lock button to start the arming process. Wait 30 seconds. Perform the following check in a temperature controlled environment. Pull the plunger of the striker tool all the way out to tap the center of the driver's door window again to trigger an alarm. Insert the key into the driver's door key cylinder and turn it toward the back of the vehicle to stop the alarm Look For: Refer to step #18. After 30 seconds, the LED starts flashing; the system is now armed. The horn sounds repeatedly. The headlights flash repeatedly. The tail and maker lights flash repeatedly. The LED lights up. NOTE: Adjust as necessary by increasing the GBS set ting to the next level if the alarm does not trigger during the functional verifications. NOTE: If you do not disarm the system, the alarm will last 20 seconds. It is not necessary to check the alarm duration. Refer to step #21. Page 19 of 28 Pages
20 Section III - Functional Verifications Section III - Functional Verifications Check: Look For: Vehicle Function Checks: Head Lights High Beams Turn Signal Lights Tail Lights Stop Lights Backup Lights Hazard Lights Marker Lights Dome/ Courtesy Lights Panel/ Switch Illumination Accessory Controls/ Illumination (if equipped) Key Sensor Buzzer Fog Lights (if equipped) Daytime Running Lights (if equipped) Trunk/ Tailgate/ Bed lights (if equipped) Glove Box Light (if equipped) Cruise Control Light (if equipped) Seat Belt Warning Light Air Bag ABS Light (if equipped) Lamp Failure Sensor (if equipped) Track/ Skid Control Light (if equipped) Functioning Head Lights Functioning High Beams Functioning Turn Signal Lights Functioning Tail Lights Functioning Stop Lights Functioning Backup Lights Functioning Hazard Lights Functioning Marker Lights Functioning Dome/ Courtesy Lights Functioning Controls/ Illumination Functioning Accessory Functioning Key Sensor Functioning Fog Lights Functioning DR Lights Functioning Lights Functioning Glove Box Light Functioning Cruise Control Light Functioning Seat belt Warning Light. If the warning light remains ON, it may indicate a system malfunction. Functioning Air Bag Warning Light. If the warning light remains ON, it may indicate a system malfunction. Functioning ABS Light. If warning light remains ON, it may indicate a system malfunction. Functioning Lamp Failure Light. If the warning light remains ON, it may indicate a system malfunction. Functional Track/ VSC Light. If the warning light remains ON, it may indicate a system malfunction. Page 20 of 28 Pages
21 Section III - Functional Verifications Section III - Functional Verifications Check: HVAC Power Locks (if equipped) Power Windows (if equipped) Power Seats (if equipped) Power Sunroof (if equipped) Horn Gauges Front Wiper/ Washer Rear Wiper/ Washer (if equipped) Clock (if equipped) Accessory Power Socket (if equipped) Starter Audio/ Video (if equipped) Power Sliding Door (if equipped) Convenience Memory Settings (if equipped) Heated Seats (if equipped) Massage Seats (if equipped) Rear Window Defogger (if equipped) Side Mirror Defogger (if equipped) Front Windshield Defogger (if equipped) Navigation System (if equipped) Look For: All HVAC Controls Function Functioning Power Locks Functioning Power Windows Functioning Power Seats Functioning Sunroof Functioning Horn Functioning Gauges Functioning Front Wiper/ Washer Functioning Rear Wiper/ Washer Functioning Clock Functioning Accessory Power Socket Functioning Starter Functioning Audio/ Video Functioning Power Sliding Door Functioning Convenience Memory Settings Functioning Heated Seats Functioning Massage Seats Functioning Rear Window Defogger Functioning Side Mirror Defogger Functioning Front Windshield Defogger Functioning Navigation System Page 21 of 28 Pages
22 Section IV - Installation Process/Audit Criteria Process A. Vehicle Disassembly Section IV: Audited during accessory installation Paragraph numbers refer to paragraph numbers in Section II Part Number: Disconnect the negative battery cable. (Fig. A1) i. Cover the fender before starting. Process/Audit Criteria Audit Audited on completed vehicle installation Be careful not to touch the positive battery cable. 2. Remove the driver side step cover. (Fig. A2) i. Protect the seat and floor before starting. i Do not scratch the cover. 3. Remove the driver s cowl cover. (Fig. A3) i. Do not scratch the cover. 5. Remove the lower dash cover. (Fig. A4) Do not scratch the cover. 6. Prepare a blanket, then place the blanket over the front edge of the center console. (Fig. A5) 7. Loosen the bracket cover, but do not remove the cover. (Fig A6) i Do not scratch the cover. Do not bend the cover. B. Piezo Buzzer Installation 1. Remove and save the three bolts securing R/B No. 2 to the body in the engine room. (Fig. B1) 3. Plug in the Piezo Buzzer s gray 2P connector into the vehicle harness' gray 2P connector. (Fig. B2) Page 22 of 28 Pages
23 Section IV - Installation Process/Audit Criteria Process Section IV: Audited during accessory installation Paragraph numbers refer to paragraph numbers in Section II Process/Audit Criteria Audit Audited on completed vehicle installation 4. Secure the Piezo Buzzer to the vehicle s harness with one large strip of foam tape, then secure the Piezo Buzzer to the vehicle s harness with one large wire tie. (Fig. B3) i. Do not cover the opening of the Buzzer with the foam tape. 5. Bundle the extra length of the Piezo Buzzer s harness to the vehicle s harness with one large wire tie. (Fig. B4) C. V3 Harness Installation 1. Locate and disconnect the white 12P connector from the driver s side cowl area. (Fig. C1) i. Do not pull on the wires; pull on the connector. 2. Plug in the V3 harness white 12P connector into the vehicle s white 12P connector and the driver s side connector block. (Fig. C2) 3. Wrap the white 12P connectors with one large strip of foam tape. (Fig. C3) D. ECU Preparation and Installation 1. Turn the adjustment screw on the V3 ECU to the 5 position. (Fig. D1) 2. Plug in the V3 harness ECU connectors to the V3 ECU. (Fig. D2) Page 23 of 28 Pages
24 Section IV - Installation Process/Audit Criteria Process Section IV: Audited during accessory installation Paragraph numbers refer to paragraph numbers in Section II Process/Audit Criteria Audit Audited on completed vehicle installation 3. Using 3M Prep Solvent -70, clean the area indicated on the driver side cowl area. (Fig. D3) 4. Remove the backing sheet, and attach the butyl tape near the driver s side cowl area as shown. (Fig D3) i. Do not touch the adhesive surface of the butyl tape. 5. Remove the backing sheet, and attach the V3 ECU as shown. (Fig. D4) i. Do not touch the adhesive surface of the butyl tape. Press the V3 ECU to the driver side cowl area firmly. 6. Secure the V3 ECU to the driver s side cowl area with one extra large wire tie as shown. (Fig. D5) i. Clip the wire tie. 7. Attach two large foam tapes to the surface of the V3 ECU. (Fig. D6) E. V3 Harness Installation (Continued) 1. Place the white 12P connector into the hole of driver s side connector block area. (Fig. E1) 3. Plug in the V3 harness white 6P connector into the vehicle s 6P connector. (Fig. E2) 4. Wrap the white 6P connector with one small strip of foam tape. (Fig. E3) Page 24 of 28 Pages
25 Section IV - Installation Process/Audit Criteria Process Section IV: Audited during accessory installation Paragraph numbers refer to paragraph numbers in Section II Process/Audit Criteria Audit Audited on completed vehicle installation 5. Route the V3 harness up toward the Instrument Panel J/B, then secure it to the vehicle s harness with two medium wire ties. (Fig E4) 6. Locate and disconnect the white 22P connector from the Instrument Panel J/B. (Fig. E5) i. Do not pull on the wires; pull on the connector. 7. Plug in the V3 harness white 22P connector between the vehicle harness white 22P connector and the Instrument Panel J/B. (Fig. E6) 8. Secure the V3 harness to the Instrument Panel J/B with one large wire tie. (Fig. E7) 9. Attach the 22P connectors and the V3 harness to the Instrument Panel J/B with one small strip of foam tape. (Fig. E8) 10. Locate and disconnect the white 9P connector from the back side of Instrument Panel J/B. (Fig. E9) i. Do not pull on the wires; pull on the connector. 11. Plug in the V3 harness white 9P connector between the vehicle harness white 9P connector from the back side of the Instrument Panel J/B. (Fig. E10) 12. Route the V3 harness up toward the Instrument Panel J/B area, then secure the white 9P connector to the vehicle harness with one large wire tie. (Fig. E11) Page 25 of 28 Pages
26 Section IV - Installation Process/Audit Criteria Process Section IV: Audited during accessory installation Paragraph numbers refer to paragraph numbers in Section II Process/Audit Criteria Audit Audited on completed vehicle installation 13. Route the V3 harness behind the heater duct, to the Instrument Panel J/B and steering column area, then secure it to the vehicle harness with one medium wire tie. (Fig. E12) 14. Locate and disconnect the gray 3P connector from near the back side of the Instrument Panel J/B. (Fig. E13) i. Do not pull on the wires; pull on the connector. 15. Plug in the V3 harness gray 3P connectors into the vehicle s gray 3P connectors. (Fig. E14) 16. Locate and disconnect the white 8P connector from the ignition switch. (Fig. E15) i. Do not pull on the wires; pull on the connector. 17. Plug in the V3 harness white 8P connector between the vehicle harness white 8P connector and ignition switch. (Fig. E16) 18. Secure the V3 harness to the vehicle harness with one medium wire tie. (Fig. E17) 20. Secure the V3 harness fuse and V3 harness to the vehicle harness with one medium wire tie. (Fig. E18) 21. Route the V3 harness toward the center console area, then secure it to the vehicle harness with one medium wire tie. (Fig. E19) Page 26 of 28 Pages
27 Section IV - Installation Process/Audit Criteria Process Section IV: Audited during accessory installation Paragraph numbers refer to paragraph numbers in Section II Process/Audit Criteria Audit Audited on completed vehicle installation F. Status Monitor Installation 1. Remove and discard the knockout cover from the bracket cover. (Fig. F1) i. Do not scratch the cover. Do not bend the cover. 2. Install Status Monitor to the bracket cover. (Fig. F1) i. Do not scratch the cover. 3. Plug in the V3 harness white 4P connector to the Status Monitor s white 4P connector. (Fig. F2) 4. Wrap the white 4P connectors with one small strip of foam tape. (Fig. F2) G. Warning Label Installation 1. Clean the inside surface of the front door windows. (Fig. G1) 2. Place the warning label on the inside surface of the front door windows as shown. (Fig. G1) i. Use a piece of clear adhesive tape to lift the labels off of their protective backing sheet. Do not touch the adhesive surface of the warning labels. Page 27 of 28 Pages
28 Section IV - Installation Process/Audit Criteria Process Section IV: Audited during accessory installation Paragraph numbers refer to paragraph numbers in Section II Process/Audit Criteria Audit Audited on completed vehicle installation H. Completing the Installation 1. Complete the reassembly of the vehicle. i. Reconnect any disconnected connectors. Verify the panels fit together properly with no uneven gaps between them. 3. Reconnect the vehicle's negative battery cable. (Fig. H1) i. Position the negative battery terminal at an angle of 45 to the battery as shown. 3. Tighten the nut with 3 ft lbs of torque. i Be careful to not touch the positive battery terminal. 4. Leave the owner s manual, warranty card, and remote controls in their protective bags and place in the glove box. Page 28 of 28 Pages
TOYOTA TUNDRA TVIP V3 (RS3000) Section I - Installation Preparation
Section I - Installation Preparation Part Number: 0886-34861 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Status Monitor 3 1 Piezo Buzzer 4 1
More informationSCION xa LIMITED EDITION SECURITY WITH RKE (V3)
Preparation Part Number: 08586-53840 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 V3 Security ECU 3 2 Remote Control Transmitters 4 1 Piezo Buzzer 5 1 Status Monitor 6 1 Radar Sensor
More informationTOYOTA RAV TVIP V3
Section I Installation Preparation Part Number: 08586-4A872 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Status Monitor 3 1 Piezo Buzzer 4 1 V3
More informationTOYOTA RAV TVIP V5
Preparation Part Number: 08586-42810 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 GBS ECU 3 1 Security ECU Mounting Bracket 4 1 GBS ECU Mounting Bracket 5 1 Status Monitor 6 1 Security
More informationTOYOTA TACOMA 2005 TVIP V5 (RS3200 PLUS) Preparation
Preparation Part Number: 08586 04840 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Security ECU 3 1 GBS ECU 4 1 Status Monitor 5 2 Warning Labels 6 1 Owner s Manual 7 1 Warranty Card
More informationTOYOTA TACOMA TVIP V5
Preparation Part Number: PT398-35090 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Security ECU 3 1 GBS ECU 4 1 Status Monitor/Microphone 5 2 Warning Labels (English) 6 2 Warning
More informationTOYOTA YARIS HATCHBACK TVIP V3 (RS3200) Preparation
Preparation Part Number: 08586-53810 Kit Contents Item # Quantity Reqd. Description 1 1 V3 ECU 2 1 Piezo Buzzer 3 1 Wire Harness 4 1 ECU Mounting Bracket 5 2 Remote Control Transmitter 6 1 Butyl Tape 7
More informationTOYOTA HIGHLANDER TVIP V2 (GBS ADD ON) Preparation
Preparation Part Number: 08586-48070 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 GBS ECU 3 1 ECU Mounting Bracket Hardware Bag Contents Item # Quantity Reqd. Description 1 1 Microphone
More informationSCION xa 2004 SECURITY WITH RKE (V3) Section I Installation Preparation
Section I Installation Preparation Part Number: 08586 52970 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 V3 Security ECU 3 2 Remote Control Transmitters
More informationSCION tc SECURITY (V5) Preparation
Preparation Part Number: PT398-21070 Kit Contents Item # Quantity Reqd. Description 1 1 2 1 GBS ECU Hardware Bag Contents Item # Quantity Reqd. Description 1 1 V5 Security ECU 2 1 ECU Mounting Bracket
More informationTOYOTA FJ CRUISER TVIP V5 Preparation
Preparation Part Number: 08586-36822 Conflicts Do not be installed in vehicles with factory Anti-theft alarm, or Vehicle without Factory Keyless Entry Systems. Recommended Sequence of Application Item
More informationTOYOTA TACOMA 2001 TVIP V3 (RS3000) Section I Installation Preparation
Section I Installation Preparation Part Number: 08586 3D841 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Status Monitor 3 1 Piezo Buzzer 4 2 Butyl
More informationTOYOTA CAMRY HYBRID TVIP V5 (RS3200 PLUS) Preparation
Preparation Part Number: 08586-3T940-AA Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 3 1 ECU Mounting Bracket NOTE: Part number of this accessory may not be the same as the part number
More informationTOYOTA CAMRY TVIP V2 (GBS WITH ADD ON)
Preparation Part Number: 08586-3T930 Kit Contents Item # Quantity Reqd. Description 1 2 Wire Harness (One wire harness is only for RS3200+) 2 1 GBS ECU 3 1 GBS Mounting Bracket 4 1 Microphone Hardware
More informationSCION xb 2004 SECURITY (V5) Section I Installation Preparation. Part Number:
Section I Installation Preparation Part Number: 08586 52960 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Mounting Bracket 3 1 GBS ECU 4 1 Security
More informationTOYOTA PRIUS 2010 TVIP V5 PREPARATION
PREPARATION Part #: PT398-47090 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.
More informationTOYOTA TACOMA TVIP V5
Preparation Part Number: PT398-35121 Conflicts Note: Must not be installed in Vehicles with Factory Alarm System and 2013- Vehicles with (4WD Double Cab 6MT and Off-Road Package). Kit Contents Item # Quantity
More informationTOYOTA PRIUS 2004 TVIP V2 (GBS ADD ON) Section I Installation Preparation
Section I Installation Preparation Part Number: 08586 47840 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 3 1 ECU Mounting Bracket Hardware Bag
More informationTOYOTA TUNDRA TVIP V4 REMOTE ENGINE STARTER (RES)
Preparation Part Number: 08586-OC910 Conflicts Do not install into vehicles without RKE systems. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM Radio NOTE:
More informationLEXUS RX TVIP V2 PREPARATION
PREPARATION Part #: PT398-48090 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Vehicles without Factory Alarm System. Kit Contents GBS
More informationTOYOTA TUNDRA TVIP V5
Preparation Part Number: PT398-34142 Conflicts Do not install into vehicles with Factory Alarm Systems or SR grade vehicles. Do not use Techstream Lite for Registration. Recommended Sequence of Application
More informationTOYOTA VENZA 2009 TVIP V2 PREPARATION
PREPARATION Part #: PT398-0T092 Conflicts: Kit Contents Do not install into Vehicles without Factory Alarm System. GBS ECU GBS ECU Bracket GBS Harness GBS Microphone Wire Tie Foam Tape M6 Tapping Screw
More informationLEXUS CT 200h 2011 TVIP V2 PREPARATION
PREPARATION Part #: PT398-76110 Conflicts: Kit Contents GBS ECU V2 Harness GBS ECU Bracket Nut Microphone Foam Tape Wire Tie x1 x1 x1 x1 x1 x2 x15 08190-0C820 08192-6C820 Window Label Owner s Guide PT398-60084
More informationLEXUS ES TVIP V2 PREPARATION
PREPARATION Part #: PT398-33132 Conflicts: Kit Contents GBS ECU GBS ECU Bracket V2 Harness M6 Bolt Washer Wire Tie GBS Microphone x1 x1 x1 x1 x1 x5 08190-0C820 91651-60618 08192-6C820 x1 Foam Tape V2 Window
More informationTOYOTA TUNDRA TVIP V5
Preparation Part Number: 08586-OC890 Conflicts Do not install into vehicles with Factory Alarm Systems or without Immobilizer. Do not use Techstream Lite for Registration. Recommended Sequence of Application
More informationTOYOTA VENZA w/smart 2009 TVIP V4 PREPARATION
PREPARATION Part #: PT398-0T110 Conflicts: Will not program with Techstream Lite. Kit Contents RES ECU RES ECU Bracket RES Harness M6 Screw Wire Tie Splicing Connector Remote Label x1 x1 x1 x1 x5 x1 x2
More informationTOYOTA SEQUOIA TVIP V4 REMOTE ENGINE STARTER (RES)
Preparation Part Number: PT398-34111 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts Do not install into vehicles without RKE system. Recommended Sequence of
More informationTOYOTA COROLLA 2009 TVIP V4 PREPARATION
PREPARATION Part #: PT398-02080 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.
More informationTOYOTA PRIUS 2010 TVIP V4 PREPARATION
PREPARATION Part #: PT398-47091 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Manual Transmission Vehicles or Vehicles without RKE systems.
More informationTOYOTA RAV4 w/smart 2009 TVIP V4 PREPARATION
PREPARATION Part #: PT398-42110 Conflicts: Do not install into Vehicles manufactured from November 2012 and Onwards. Kit Contents RES ECU Gateway ECU RES ECU Bracket Gateway ECU Bracket Remote Label Key
More informationTOYOTA Highlander / Highlander HV 2014 TVIP V2 PREPARATION
PREPARATION Part #: PT398-48141 Conflicts: Do not install into Vehicles without Factory Alarm System. Kit Contents GBS ECU GBS ECU Bracket V2 Harness M6 Nut Bolt Jumper Connector Wire Tie DISCARD x1 08190-0C820
More informationTOYOTA COROLLA 2010 TVIP V4 PREPARATION
PREPARATION Part #: PT398-02080 or PT398-02100 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts: Do not install into Manual Transmission Vehicles or Vehicles
More informationTOYOTA CAMRY wo/smart entry TVIP V4 REMOTE ENGINE STARTER (RES)
Preparation Part Number: 08586-3T950 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 RES ECU 3 1 BUS ECU 4 1 ECU Mounting Bracket (A) 5 1 ECU Mounting Bracket (B) 6 1 Butyl Tape Hardware
More informationLEXUS RX 450h 2010 TVIP V4 PREPARATION
PREPARATION Part #: PT398-48112 Conflicts: Kit Contents Will not Program with Techstream Lite. RES ECU RES ECU Bracket RES Harness Key Tag Engine Room Label Remote Label Window Label English x2 English
More informationTOYOTA HIGHLANDER w/smart Key TVIP V4 REMOTE ENGINE STARTER (RES) Part Number: PT
Preparation Part Number: PT398-48083 Conflicts Do not install into vehicles without RKE systems. Will not program with Techstream Lite. Recommended Sequence of Application Item # Accessory Kit Contents
More informationTOYOTA HIGHLANDER w/o Smart Key TVIP V4 REMOTE ENGINE STARTER (RES)
Preparation Part Number: PT398-48111 Conflicts Do not install into vehicles without RKE systems. Recommended Sequence of Application Item # Accessory Kit Contents Item # Quantity Description 1 1 Wire Harness
More informationConflicts. Scion FR-S Keyless Entry Upgrade Alarm Part Number: Code: YQ20. Vehicle Service Parts (may be required for reassembly)
2013 - Part Number: 00016-32910 Code: YQ20 Conflicts Kit Contents Item# Quantity Req. Description 1 1 Security Module 2 1 Shock Sensor, Dual Stage 3 1 LED / Valet Swicth 4 2 Window Warning Decals 5 1 Shock
More informationTOYOTA YARIS KEYLESS ENTRY SYSTEM
TOYOTA YARIS 2011 - KEYLESS ENTRY SYSTEM Part Number: 00016-32901 Accessory Code: KE1 Conflicts Not for installation in vehicles equipped with factory installed keyless entry. Kit Contents Item # Quantity
More informationTOYOTA TUNDRA TVIP V4 Preparation
Preparation Part Number: PT398-00100 PT398-00100-AA Conflicts Do not install into vehicles without RKE system. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM
More informationVehicle Service Parts (may be required for reassembly) Legend
Toyota Part Number: 00016-32901 Accessory Code: KE1 Corolla 2014 Note: Not for installation on vehicles equipped with factory keyless entry Additional Items Required For Installation Item# Quantity Req.
More informationConflicts. Camry L (ECO Grade) Security System with Keyless Entry. Part Number: Accessory Code: QK1
2013- Part Number: 00016-32905 Accessory Code: QK1 Conflicts Note: NOT FOR INSTALLATION ON VEHICLES WITH FACTORY THEFT DETERRENT SYSTEMS. Kit Contents Item # Quantity Reqd Description 1 1 Keyless Security
More informationLEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT944-24150 Kit Contents Item # Quantity Reqd. Description 1 2 Inner LED Scuff 2 2 Outer Scuff 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 15 20
More informationTOYOTA SIENNA w/smart Key and Factory Alarm 2015 TVIP V4 PREPARATION
PREPARATION Part #: PT398-08150 Conflicts: Kit Contents Do not install into Vehicles without Smart Key and Factory Alarm. RES ECU RES ECU Bracket V4 Harness Nut Wire Tie Remote Label Key Tag x1 PT398-0T097
More informationVehicle Service Parts (may be required for reassembly) Legend
Toyota Corolla 2016 Part Number: 00016-32901 Accessory Code: KE1000 Conflicts Note: Not for installation on vehicles equipped with factory keyless entry Additional Items Required For Installation Item#
More informationXM Adapter Cable (P/N: ) MUST be used for this vehicle.
TOYOTA 2013 - Part Number:00016-00076 Code: RX30 XM Adapter Cable (P/N: 00016-00076-10) MUST be used for this vehicle. Conflicts 1. Entune 2. Vehicle s with factory XM radio Kit Contents Item # Qty Description
More informationTOYOTA AVALON EC REARVIEW MIRROR
Section I - Installation Preparation Part Number: PT732-07000 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Full Mirror Assembly, Compass 2 1 Hardware Bag 3 1
More informationConflicts. TOYOTA Camry XM Satellite Radio. Part Number: Code: RX30. Vehicle Service Parts (May be required for reassembly)
TOYOTA 2013 - Part Number:00016-00076 Code: RX30 Conflicts 1. Entune 2. Vehicle s with factory XM radio Kit Contents Item # Qty Description 1 1 XM Module 2 1 XM Tuner Module 3 1 Wiring Harness 4 1 Hardware
More informationTOYOTA im INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1
More informationTOYOTA 4Runner Keyless Entry Upgrade Alarm
TOYOTA 4Runner 2013 - Keyless Entry Upgrade Alarm Part Number: 00016-32910 Accessory Code: QSNS10 Conflicts Note: NOT FOR INSTALLATION ON VEHICLES EQUIPPED WITH SMART KEY General Applicability Used on
More informationColor Applicability/Trim Level. Hardware Bag Contents Item # Quantity Reqd. Description
Document # 2291 (TMS) Posted 1/30/04 SCION xb 2004-2005 FOG LIGHT Section I Installation Preparation Part Number: 08590-52820 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description
More informationTOYOTA TACOMA EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-35052 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 1 T-tap Connectors,
More informationTOYOTA TACOMA INTERFACE KIT FOR IPOD Preparation
Preparation Part Number: PT545-00082 Kit Contents Item # Quantity Reqd. Description 1 1 Unit Assembly Kit 2 1 Mounting Kit 3 1 Hardware Bags 4 1 Unit and Fit Kit List 5 1 Owner s Manual Unit Assembly Kit
More informationConflicts. TOYOTA Prius XM Satellite Radio. Part Number: Code: RX30. Vehicle Service Parts (May be required for reassembly)
TOYOTA Prius 2013 - Part Number:00016-00076 Code: RX30 Conflicts 1. Entune 2. Vehicle s with factory XM radio Kit Contents Item # Qty Description 1 1 XM Module 2 1 XM Tuner Module 3 1 Wiring Harness 4
More informationConflicts. Prius C 2014 Keyless Entry Upgrade. TOYOTA Part Number: Code: QS10. Vehicle Service Parts (May be required for reassembly)
TOYOTA Part Number:00016-47032 Code: QS10 Conflicts 1. Vehicle's with out factory immobilizer Kit Contents Item# Quantity Req. Description 1 1 Security Module 2 1 Shock Sensor, Dual Stage 3 1 LED / Valet
More informationTOYOTA TUNDRA IMPACT SENSOR
TOYOTA TUNDRA 2010 - IMPACT SENSOR Part Number: 00016-47031 Accessory Code: QG1 Kit Contents Item # Quantity Reqd. Description 1 1 Security Interface Module 2 1 Shock Sensor 3 1 Main Harness 4 1 Hardware
More informationTOYOTA PRIUS V 2012 TVIP V4 PREPARATION
PREPARATION Part #: PT398-47121 Conflicts: Will not program with Techstream Lite. Kit Contents Screw RES ECU RES ECU Bracket Hood Switch V4 Harness Remote Label (for Hood SW) Wire Tie PT398-0T097 x1 x1
More informationTOYOTA SOLARA EC REARVIEW MIRROR Section I - Installation Preparation
Section I - Installation Preparation Part Number: PT374-33020 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/compass 2 1 Hardware Bag 3 1 Installation
More informationTOYOTA HIGHLANDER IMPACT SENSOR
TOYOTA HIGHLANDER 2010 - IMPACT SENSOR Part Number : 00016-47031 Accessory Code: QG1 Conflicts Not for installation on vehicles with factory theft deterrent systems - hybrid. Kit Contents Item # Quantity
More informationKeyless Upgrade Alarm
Toyota Matrix 009 - Keyless Upgrade Alarm Part Number: 0006-940 Accessory Code: QS Kit Contents Item # Quantity Reqd Description Security Module Shock Sensor 3 LED Valet Switch 4 HP Switch Ext. 5 Window
More informationTOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT413-42130 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 3 Hardware Bag Contents Item # Quantity Reqd. Description 1 20 Cable Tie 2 2 Scotchlok 3 2 Foam Pad
More informationTOYOTA FJ CRUISER AIR DAM/LIGHT BAR Preparation
Preparation Part Number: PT278-35071 Kit Contents Item # Quantity Reqd. Description 1 1 Air Dam / Light Bar Hardware Bag 1 Contents Item # Quantity Reqd. Description 1 2 Screw, M6x33mm, Wafer Head 2 2
More informationScion xb EC Rearview Mirror w/ Shift Light Preparation
2008 - Preparation Part Number: 00016-79800 Accessory Code: YM10 Kit Contents Item # Quantity Reqd. Description 1 1 Mirror Assembly w/ PRNDL 2 1 Hardware bag 3 1 Installation Manual Hardware Bag Contents
More informationTOYOTA TACOMA HANDS FREE BLU LOGIC Preparation. Item 5 Item 6 Item 7 Item 8. Item 4. General Applicability Note: Recommended Tools
TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00098 Conflicts: JBL Audio, Factory Navigation Kit Contents: NOTE: Part number of this accessory may not be the same as the part number
More informationSCION tc Navigation System Preparation. Part Number: PT
Preparation Part Number: PT611-21111 Kit Contents Item # Quantity Reqd. Description 1 1 Navigation System 2 1 GPS Antenna 3 1 Bluetooth Antenna 4 1 Wire Harness (Reverse / Park Brake) 5 1 RCA Relay Cable
More informationSCION tc ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PTS21-21070 Kit Contents Item # Quantity Reqd. Description 1 2 Hardware Kit w/ power harness 2 1 Front Left Illuminated Door Sill Protector 3 1 Front Right Illuminated Door Sill
More informationLEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-30120 (GS350) PT922-30130 (GS450h) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Req'd. Description 1 1 Illuminated
More informationConflicts. TOYOTA Highlander CAR LINK (W/O Remote Start) Part Number: Accessory Code: QL1. Doc PIO / DIO Rev.
Doc. 06.107.00 PIO / DIO Rev. A 04/26/11 TOYOTA Highlander 2011 - CAR LINK (W/O Remote Start) Part Number: 00016-00077 Accessory Code: QL1 Conflicts Note: Kit Contents Item # Quantity Reqd. Description
More informationTOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT942-02140 Kit Contents Item # Quantity Reqd. Description 1 1 Illuminated Scuff plate, Front Right Hand 2 1 Illuminated Scuff plate, Front Left Hand 3 1 Door Scuff plate, Rear
More informationTOYOTA TACOMA LED DRL Black-Out
TOYOTA TACOMA 2013 - LED DRL Black-Out Part Number: 00016-35021 Accessory Code: LDBO10 Conflicts - Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 1 Driver Box 3 1 Harness bag
More informationTOYOTA RAV INTERFACE KIT FOR IPOD Preparation Part Number: PT
Preparation Part Number: PT545-00082 NOTE: Part number of this accessory may not be the same as the part number shown. General Applicability Note: Kit Contents Item # Quantity Reqd. Description 1 1 Unit
More informationFORM: C 01/06
Accessory Color Document # 3802 REVISION B 01/09/06 Part Number: 00016-21910 Accessory Code:YQ4 Kit Contents Item # Quantity Reqd Description 1 1 MPX Security Module 2 1 Shock Sensor 3 1 LED Valet Switch
More informationTOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation
TOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation Part Number: PT297-35061 Kit Contents Item # Quantity Reqd. Description 1 2 Driving Lamp Assembly 2 1 Switch Harness 3 1 Lamp Harness 4 2 Stone Shield
More informationConflicts - Fog Lights
TOYOTA CAMRY 2013 - BLACKOUT LED DRL Part Number: 00016-32270 Accessory Code: LDBO10 Conflicts - Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 2 DRL s bezels 3 1 Driver Box
More informationTOYOTA COROLLA ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT942-02140 Kit Contents Item # Quantity Reqd. Description 1 1 Illuminated Scuff plate, Front Right Hand 2 1 Illuminated Scuff plate, Front Left Hand 3 1 Door Scuff plate, Rear
More informationTOYOTA TACOMA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-35090 Tuner Assembly 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item
More informationCAMRY STRIP LED DRL TOYOTA Part Number: Accessory Code: LDRS10. PIO / DIO Rev. A 02/26/13. Doc
Doc. 02.126.00 TOYOTA CAMRY PIO / DIO Rev. A 2013-02/26/13 STRIP LED DRL Part Number: 00016-32280 Accessory Code: LDRS10 Conflicts - Only works on Camry SE Kit Contents Item # Quantity Reqd. Description
More informationTOYOTA PRIUS XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-4700 Tuner Assy 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item # Quantity
More informationTOYOTA CAMRY HANDS FREE BLU LOGIC Preparation
TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationPart Number: TAV-713 TOYOTA AVALON LED DRL
Part Number: TAV-713 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion pad 6 1 Switch 7 2 Drill Jigs Hardware Bag Contents
More informationScion xa SATELLITE RADIO TUNER Preparation
Preparation Part Number: PTS31-00051 Kit Contents Item # Quantity Reqd. Description 1 1 Antenna, Interior 2 1 Antenna Tape Pad 3 1 Wire Harness 4 1 Bracket, Floor 5 3 Hardware Bags 6 3 Templates 7 1 SIRIUS
More informationTOYOTA SIENNA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit: PT546-08070 Tuner Assy: 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting Kit Contents
More informationTOYOTA SIENNA LED DRL Black-Out
TOYOTA SIENNA 2013 - LED DRL Black-Out Part Number: 00016-08021 Accessory Code: LDBO10 Conflicts - Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 2 DRL s bezels 3 1 Driver
More informationLEXUS CT 200h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-89100 Kit Contents Item # Quantity Req'd. Description 1 1 Door Sill, Front Right Hand 2 1 Door Sill, Front Left Hand 3 1 Door Sill, Rear Right Hand 4 1 Door Sill, Rear Left
More informationSCION tc PREMIUM AUDIO Preparation. Part Number: PT (Extension Module w/ AHA)
Preparation Part Number: PT296-12160 Kit Contents Item # Quantity Reqd. Description 1 1 Extension Module 2 1 BT cable 3 1 DA/Ext Harness 4 1 GPS Antenna kit 5 6 Bolt (M5x8) 6 5 Wire tie (10 ) Hardware
More informationPart Number: T4R-2IN1
Date: 12.11.2014 TOYOTA HIGHLANDER 2015 LED Fog Light & DRL 2in1 Part Number: T4R-2IN1 Kit Contents Item # Quantity Reqd. Description 1 2 DRL + Fog Light Housing 2 1 Driver Box 3 1 Harness bag 4 1 User
More informationTOYOTA TACOMA XSP-X LED DRL. Part Number: Accessory Code: LDRL10
TOYOTA TACOMA 2013 - XSP-X LED DRL Part Number: 00016-35230 Accessory Code: LDRL10 Conflicts -None Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3 1 Harness bag 4 Hardware Bag
More informationSCION xa 2004 FOG LIGHT Section I Installation Preparation. Part Number: General Applicability
Section I Installation Preparation Part Number: 81025 52080 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Assembly, RH 2 1 Assembly, LH 3 1 Switch, 4 1 Relay, 5
More informationTOYOTA SOLARA CONVERTIBLE XM SATELLITE RADIO Preparation. Part Number: Mounting Kit PT
Preparation Part Number: Mounting Kit PT546-06061 Tuner Assy 86180-0W030 Tuner Assy Kit Contents (86180-0W030) 1 1 Tuner Assy, Stereo Component Mounting Kit Contents (PT546-06061) 1 Ground Cable 1 1 Wire,
More informationTOYOTA tc HANDS FREE BLU LOGIC Preparation
TOYOTA tc 2011- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationTOYOTA CAMRY EC REARVIEW MIRROR Preparation
TOYOTA CAMRY 2010 - EC REARVIEW MIRROR Preparation Part Number: 00016-09101 Code: CM9 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ Compass 2 1 Hardware bag Hardware Bag Contents
More informationGeneral Applicability Note: Recommended Tools. Personal & Vehicle Protection Safety Goggles Seat Covers Floor Covers Special Tools. Installation Tools
TOYOTA HIGHLANDER/HIGHLANDER HV 2008- Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationSCION xb 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationPart Number: T4R-2N1. Hardware Bag Contents. General Applicability. Conflicts - Limited Models
Date: 12.11.2014 TOYOTA HIGHLANDER 2014-2016 LED Fog Light & DRL 2 in 1 Part Number: T4R-2N1 Kit Contents Item # Quantity Reqd. Description 1 2 DRL + Fog Light Housing 2 1 Driver Box 3 1 Harness bag 4
More informationKia Sedona. Installation Manual: Kia Sedona. Power Lift Gate System. Page 1 of 13
Kia Sedona Installation Manual: Kia Sedona Power Lift Gate System Page 1 of 13 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage caused
More informationTOYOTA RAV FOG LIGHT KIT Preparation
Preparation Part Number: PT413-42163 Kit Contents Item # Quantity Reqd. Description 1 7 7 Wire Tie 2 4 #10-16 Cross Pan-Washer Head Screws 3 1 Switch 4 1 Relay 5 1 LH Fog Light Bezel 6 1 RH Fog Light Bezel
More informationTOYOTA Matrix XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-12080 Tuner Assembly 86180-0W031 (Music Only) Tuner Assembly PT546-00090 (Music Plus Data) NOTE: Part number of this accessory may not be the same as the part
More informationTOYOTA YARIS XM SATELLITE RADIO Preparation (Sedan & Hatchback)
Preparation (Sedan & Hatchback) Part Number: Mounting Kit PT546-52096 Tuner Assy 86180-0W031 Tuner Assy Kit Contents (86180-0W031) Item # Quantity Reqd. Description 1 1 Tuner Assy, Stereo Component Mounting
More informationPart Number: STC-501. Hardware Bag Contents. General Applicability. Conflicts. Date: SCION tc LED DRL in FOG LIGHT HOUSING
Date: 09.30.2013 SCION tc 2011-2013 LED DRL in FOG LIGHT HOUSING Part Number: STC-501 Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL housings 2 2 Bezels 3 1 Driver Box 4 1 Harness bag 5 1 User
More informationSCION XB HANDS FREE BLU LOGIC Preparation
SCION XB 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationSCION xb SIRIUS SATELLITE RADIO TUNER Preparation
Preparation Part Number: PTS3-52050 NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Reqd. Description Antenna, Exterior 2 Wire Harness 3 Bracket,
More information