Vehicle Security System

Size: px
Start display at page:

Download "Vehicle Security System"

Transcription

1 Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting components or routing wires near moving parts Tape or loom wires under hood for protection and appearance Use grommets when routing wires through metal surfaces Use a voltmeter for testing and verifying circuits Technical Support For Authorized Dealers - (800) Hours: 8:00 a.m. - 7:00 p.m. EST Monday thru Friday 10:00 a.m. - 2:00 p.m. EST Saturday This device complies with part 15 of the FCC rules and with RSS-210 of the industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Z13 INS0885 Rev. A 12/98

2 System Layout Refer to Wire Color / Location Chart for specific wire color, location, and polarity information. Brown Door LOCK / UNLOCK Polarity Disarm Input Siren / Horn Output (-) Unused 2

3 System Specifications System Arming The system will ignore all trigger inputs for 3 seconds after the second parking light flash. SilentChoice Allows selective arming or disarming of the security system with or without confirmation chirps. Pressing the arm or disarm button the first time activates the selected function. Then if the same transmitter button is pressed again within 5 seconds the siren (or horn) will chirp, confirming the selected function. Alarm Trip Cycle Siren will sound for 30 seconds. The alarm will then ignore all trigger inputs for 10 seconds, then rearm. The siren will not sound again until another intrusion is detected. However, if the intruded zone stays open the alarm will continue to cycle until zone is closed. Panic Pressing button 3 on the remote transmitter activates the Panic feature. Panic duration is 30 seconds. Panic cycle can be stopped prior to 30 seconds by pressing button 3 again. Sensors Power and Ground are active at all times on Sensor Port 1. Ground on Sensor Port 2 is active only when the alarm is fully armed. Pressing buttons 1 and 2 together will deactivate the Lite-Touch and shock input on sensor ports 1 and 2. The siren will chirp three times when these inputs are deactivated. These inputs will remain deactivated until the alarm is rearmed. 10 Lite-touch trips within one arming period will cause the alarm to ignore any further lite-touch inputs until the alarm is rearmed. 4 Full-trigger trips within one arming period will cause the alarm to ignore any further full-trigger inputs until the alarm is rearmed. Automatic Arming If the Automatic Arming option is enabled, the alarm will automatically arm and disable the vehicle starter 1 minute after the ignition is turned off. Valet Valet Mode prevents the alarm from arming automatically. Enter Valet Mode by pressing the ARM button on the remote transmitter with the vehicle ignition on. Exit by pressing DISARM with the ignition on. In Valet Mode, the LED will double-flash. Illuminated Entry/Exit The Illuminated Entry/Exit Output is activated for 60 seconds after the alarm is disarmed or the ignition is turned off. Trunk Release The Trunk Release is activated by pressing and holding DISARM on the remote transmitter. 3

4 System Specifications (cont.) Door Locks The Door Lock / Unlock Outputs are activated when the alarm is armed and disarmed. Duration is.6 seconds or 6 seconds (selectable). The Door Lock Output is activated when all doors are closed and the vehicle ignition is turned on (this option can be turned off). The Door Unlock Output is activated when the vehicle ignition is turned off (this option can be turned off). The door unlock output can be programmed to provide a double unlock pulse for vehicles requiring a pulse to the factory alarm. Trip Identification Trip ID identifies the specific zone that triggered the alarm system. Upon returning to the vehicle, press DISARM. If the siren chirps 4 times, the alarm was triggered. Press the override button. The siren will chirp a number of times, indicating the violated zone. Auxiliary Output Output can be activated by pressing and holding the ARM button. The aux. output will activate for 20 seconds. The aux. output can be shut off prior to 20 seconds by pressing ARM again. 4

5 1. Installation Remove all fuses from the wire harness before installation. A. Siren or Horn (#20 ORANGE) Follow the appropriate steps below: Siren Mount bell housing downwards. Use at least two (2) screws to secure siren to mounting location. Connect siren BLACK wire to module ORANGE wire. Connect siren RED wire to a fused +12V source. Horn Circuit verification - Negative Systems - Target wire will register ground when horn is pressed. Positive Systems - Target wire registers voltage when horn is pressed. Connection Positive Negative Horn Wire Relay Diagram 1 Connect to target wire. Fused +12V Diagram 1 Module ORANGE wire Horn B. 12-volt Main Feed (#22 RED) Circuit Verification - Target wire registers voltage at all times. Connect to vehicle battery or at main 12-volt lead at ignition switch harness. C. 12-volt Switched Feed (#17 Lt. BLUE) Circuit Verification - Target wire registers voltage when ignition key is turned to the ON position and START position. Connect at switched 12-volt lead at ignition switch harness.* D. Ground (#11 BLACK) Attach to grounded metal point of vehicle chassis. Note: When installing multiple components (such as an alarm and remote starter), ground the units separately. 5

6 1. Installation E. Starter Interrupt (WHITE/RED and WHITE on 2-pin Connector) Circuit Verification - Target wire registers voltage only when ignition key is turned to the START position. Circuit Verification after starter wire is cut: KEY SIDE of starter wire registers voltage when ignition key is turned to the START position. MOTOR SIDE of starter wire registers no voltage. Connect to WHITE/RED to Key Side at vehicle starter wire. Connect WHITE to Motor side of vehicle starter wire. Note: Some vehicles have two starter wires. If so, cut both and connect to the alarm module. Refer to Vehicle Wire Color and Location Chart. F. Door Pin Switches (#8 YELLOW (-) or #19 WHITE (+)) Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit type and location, or verify the vehicle wire using the following guideline: Positive Systems - Target wire registers voltage when any door is opened. Negative Systems - Target wire registers ground when any door is opened. Connect the appropriate module wire to the targeted vehicle wire. G. Illuminated Entry (#4 YELLOW and #3 YELLOW/BLACK) Circuit Verification - Target wire is usually the door pin switch wire. Refer to section F for verification guideline. Connect #4 Lt. YELLOW wire to the target wire. Connect #3 YELLOW/BLACK wire to +12V if the door system is positive. Connect #3 YELLOW/BLACK wire to ground if the door system is negative. H. Parking Lights (#2 ORANGE/BLACK and #1 BLACK/WHITE) Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit type and location, or verify the vehicle wire using the following guideline: Positive Systems - Target wire registers voltage when parking lights are on. Negative Systems - Target wire registers ground when parking lights are on. Connect #2 ORANGE/BLACK wire to the target wire. Connect #1 BLACK/WHITE wire to +12V if the system is positive. Connect #1 BLACK/WHITE wire to ground if the system is negative. I. Hood / Trunk Pin Switch (#7 Lt. GREEN) Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit location, or install a pin switch and connect to the module #7 Lt. GREEN wire. 6

7 1. Installation J. Power Door Locks: #14 Lt. BLUE #13 Lt. BLUE/BLACK #10 RED/BLACK #16 GREEN #15 GREEN/BLACK Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit type and location. Connections Type 1 Type 2 Type 3 Dia. 1 Dia. 2 Dia. 3 Type 4 Dia. 4 Type 5 Dia. 5 Other See specifications in Vehicle Wire Color / Location Guide or call Technical Support Diagram 1 Type 1 - Positive 3-Wire Door Lock System Diagram 2 Type 2 - Positive 5-Wire Door Lock System Diagram 3 Type 3 - Negative 3-Wire Door Lock System 7

8 1. Installation RED/BLACK 12V+ Diagram 4 MODULE WIRES BLUE/BLACK GREEN 87 87a GREEN/BLACK Type 4 - Vacuum Door Lock System Diagram 5 LT. BLUE GREEN UNUSED UNUSED MODULE WIRES RED/BLACK BLUE/BLACK GREEN/BLACK 12V+ or Type 5 - Resistor Door Lock System K. Status Indicator (#18 GRAY) Locate a visible location on the dash with 1 clearance behind the location. Drill a 1 /4 hole and snap the status indicator in place. Connect the status indicator BLACK wire to the module GRAY wire. Connect the status indicator RED wire to a fused +12-volt source. 8

9 1. Installation L. Trunk Release (#5 VIOLET and #12 TAN) Refer to Vehicle Wire Color and Location Chart for circuit type and location, or verify the vehicle wire using the following guideline: Circuit Verification: Positive Systems - Target wire registers voltage when the trunk / hatch is opened using the vehicle button. Negative Systems - Target wire registers ground when the trunk / hatch is opened using the vehicle button. Connect TAN to targeted vehicle wire Connect VIOLET to +12V for positive systems or ground for negative systems. M. Auxiliary Output - Headlight Control (#9 BLACK/GREEN) Determine the polarity needed for the accessory. Wire relay as shown. Positive Negative Diagram 6 Note: A relay is only required if accessory draws over 500mA. Fused 12V+ Fused 12V+ N. Impact Detector Using the supplied tie wrap mount the impact detector to the steering column or to a sturdy wire harness. Plug the impact detector into SENSOR PORT 1 on the module. Note: any additional sensors connect to sensor port 2 O. Armed Output (BLACK on Sensor Port 2) Connect to a device requiring a ground signal when the alarm system is armed. N. Override/Programming Button The override/programming button must be installed for all installations Find a suitable mounting location for the override/programming button. The selected mounting location should be as difficult as possible for an unauthorized person to find. It is recommended that the override button be mounted in different location in each installation. Drill a 9/32 hole mounting hole in the selected mounting location and mount as shown. Connect one of the override button wires to the module brown wire. Connect the remaining override / programming button wire to a solid chassis ground. 9

10 2. System Power-Up Check all connections and wire routing. Turn ignition to the ON position. Replace all fuses in the module harness. 3. Programming Selectable Options NOTE: Transmitters supplied with system are preprogrammed. See page 13 for instructions on programming additional transmitters. 1. Open driver s door. 2. Turn vehicle ignition ON. 3. Press and hold programming button in. After seconds siren will sound 3 times to indicate transmitter learn mode. 4. Release, press and release programming button. Siren will sound 4 times. 5. Using a programmed transmitter, press LOCK button to advance to the next option. Siren will sound to indicate option number. 6. Press DISARM to turn selected option ON or OFF. Status Indicator will light if an option is ON. 7. Turn Ignition OFF to end option programming. Button 1 Press to Advance to Next Option ARM PANIC DISARM TRUNK Button 2 Press to Turn Option ON or OFF Status Indicator Displays Option Status (ON or OFF) Press Button 3 to Reset all Options to Factory Settings Number of Siren Chirps Indicate Option Number Option Number and Description Bold Type indicates Factory Setting 1. System arms automatically 60 seconds after ignition key is turned off 2. SilentChoice 3. Doors lock when ignition is turned on enabled 4. Doors unlock when ignition is turned off enabled 5. Illuminated exit enabled 6. Lock / unlock output duration 7. Double unlock pulse enabled 8. Siren or Horn Status Indicator ON YES YES YES YES YES 6 SEC. YES SIREN Status Indicator OFF NO NO NO NO NO.6 SEC. NO HORN 10

11 Testing the Alarm System 1. Arming and Disarming / Sensor Override Close all doors and press ARM. All doors lock. Parking lights flash two times. Status indicator begins to flash. Press ARM again within 5 seconds. Siren chirps twice. Press Disarm. All doors unlock. Parking lights flash. Status indicator turns off. Courtesy light turns on (if connected) and illuminated exit is set. Press Disarm again within 5 seconds. Siren chirps one time. 2. Alarm Triggering / Starter Interrupt / Trip ID / Lock Options Arm system. Wait 5 seconds, then Siren sounds / parking lights flash. open door. horn output will also activate (certain models only). With siren sounding, attempt to Vehicle will not start. start vehicle. Wait until siren stops, then press DISARM. Siren chirps / parking lights flash 4 times (system was triggered). Press override button. Siren chirps three times (system was triggered by door). Close doors and attempt to start vehicle. Vehicle starts. Doors lock (if Ignition Lock Option is activated). Turn ignition off. Doors unlock (if Ignition Unlock Option is activated). 3. Trunk Release Press and hold DISARM. Trunk opens. 4. Panic Press PANIC. Siren sounds / parking lights flash for 30 seconds. for one second. Press PANIC button to stop. 5. Automatic Arming (Test only if Automatic Option is activated) Enter vehicle and close doors. Turn ignition Alarm arms 60 seconds after door is closed. on for five seconds, then turn off. Exit vehicle and close doors. 6. Valet (Only active if passive arming is enabled) With system disarmed, turn ignition on, Status Indicator Flashes double blink. then press ARM. Press DISARM. Flashing stops. 7. Auxiliary Outputs (Test if connected) Press and hold ARM button on the remote Accessory connected to Aux. Output activates for 20 seconds. transmitter. 11

12 Adjusting the Impact Detector 1. Turn the white knob on the impact detector clockwise until it stops, then turn counterclockwise approximately 1 / 4 of a turn. 2. Test the sensitivity by arming the alarm system, waiting 30 seconds, then slapping various parts of the vehicle with an open hand. A light slap should cause the siren to emit a warning chirp. A heavier slap should trigger the alarm. 3. Adjust the sensitivity until the desired setting is achieved. Antenna Placement / Mounting the Module 1. If the module has a short antenna (approx. 8 ), keep the antenna as straight as possible, and route away from vehicle harnesses. 2. Mount the module using supplied long tie wraps. Make sure the module and harnesses are clear of moving vehicle parts. Installation is Complete. 12

13 Programming Additional Remote Transmitters Note: Each system module has four slots, or memory locations, to store remote transmitter codes, giving it the ability to operate from up to four remote transmitters. For proper operation, a transmitter code must be stored into each memory slot. When using less than four transmitters, follow the suggested programming parameters: One Remote Transmitter - Program four (4) times Two Remote Transmitters - Program each remote transmitter two (2) times Three Remote Transmitters - Program one remote transmitter twice, and each remaining remote transmitter once. 1. Open driver s door. 2. Turn vehicle ignition ON. 3. Press and hold programming buttton. 4. After seconds, siren will sound 3 times. Release programming button. 5. Press button 1 on new transmitter. 6. Repeat step 5 to program additional transmitters (up to four). 7. Turn vehicle ignition OFF. 13

Vehicle Security System

Vehicle Security System Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

Vehicle Security System

Vehicle Security System Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED

PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED 100755-2 Installation Instructions PC 4200 PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED

PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Instructions CPL Master Module PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

Installation Instructions

Installation Instructions F20/F25 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components

More information

MM1 Installation Instructions

MM1 Installation Instructions MM1 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or

More information

Remote Keyless Entry Installation Guide ca 2051

Remote Keyless Entry Installation Guide ca 2051 PROFESSIONAL SERIES Remote Keyless Entry Installation Guide ca 2051 ca2051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...

More information

CSI-300 Installation Instructions

CSI-300 Installation Instructions CSI-300 Installation Instructions Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces

More information

6R / 5-BUTTON SERIES VEHICLE SECURITY SYSTEM

6R / 5-BUTTON SERIES VEHICLE SECURITY SYSTEM 6R / 5-BUTTON SERIES VEHICLE SECURITY SYSTEM Button 1 Button 2 Button 5 Button 3 Button 4 Standard Features: Two 5-Button Remote Transmitters Status indicator (LED) Valet / override switch Multi-tone siren

More information

Security and Keyless Entry Installation Guide ca 1051

Security and Keyless Entry Installation Guide ca 1051 PROFESSIONAL SERIES Security and Keyless Entry Installation Guide ca 1051 ca1051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection

More information

2 Way Security and Keyless Entry Installation Guide ca 1553

2 Way Security and Keyless Entry Installation Guide ca 1553 PROFESSIONAL SERIES 2 Way Security and Keyless Entry Installation Guide ca 1553 2012 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...

More information

CS-865RKE Series II REMOTE KEYLESS ENTRY SYSTEM

CS-865RKE Series II REMOTE KEYLESS ENTRY SYSTEM INTRODUCTION: CS-865RKE Series II REMOTE KEYLESS ENTRY SYSTEM INSTALLATION & OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a Remote Keyless Entry System by Crimestopper Security Products Inc.

More information

CA-110 Installation Instructions

CA-110 Installation Instructions CA-110 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components

More information

Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED. Installation Precautions:

Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED. Installation Precautions: Installation Instructions CA-6 PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or

More information

Covers All 430, 440, 441 and CJ Series Advanced Security Systems.

Covers All 430, 440, 441 and CJ Series Advanced Security Systems. INSTALL GUIDE Covers All 430, 440, 441 and CJ Series Advanced Security Systems www.ultrastarters.com Technical Support: 866-698-5872 ext 0 support@ultrastarters.com FCC/ID Notice This device complies with

More information

Owner's Manual. Remote Security and Convenience System INS0866 8/98

Owner's Manual. Remote Security and Convenience System INS0866 8/98 Remote Security and Convenience System Owner's Manual IMPORTANT NOTE: The operation of the SURESTART as described in this manual is applicable to most vehicles. However, due to the engine type and configuration

More information

CA-210 Installation Instructions

CA-210 Installation Instructions CA-210 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components

More information

ALARM UPGRADE FOR FACTORY REMOTE KEYLESS ENTRY SYSTEM INSTALLATION PRECAUTIONS & WARNINGS

ALARM UPGRADE FOR FACTORY REMOTE KEYLESS ENTRY SYSTEM INSTALLATION PRECAUTIONS & WARNINGS CS-882 OEM ALARM UPGRADE FOR FACTORY REMOTE KEYLESS ENTRY SYSTEM INSTALLATI PRECAUTIS & WARNINGS NOTE: This system does not improve or affect the range of the factory remote keyless entry transmitters.

More information

CSI-100 Installation Instructions

CSI-100 Installation Instructions CSI-100 Installation Instructions Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting

More information

2 WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE

2 WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE REV. ARS. WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This device may not cause

More information

SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL

SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL Items Supplied with the System: Installation Instructions: Main unit 1. Mounting the module: Plug In LED Mount the module in a suitable location

More information

Remote Start with Keyless Entry Installation Guide ca5054

Remote Start with Keyless Entry Installation Guide ca5054 PROFESSIONAL SERIES Remote Start with Keyless Entry Installation Guide ca5054 2014 Voxx Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin...3 Wire Connection Guide...4

More information

INSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit

INSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit R Vehicle Security INSTALLATION MANUAL Model: PLUS-4700 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference;

More information

Installation Instructions

Installation Instructions Installation Instructions for EVS II Security and Keyless Entry Systems Note: It is recommended that this installation take place prior to rustproofing. The individual delivering the vehicle should review

More information

6 RELAY SYSTEM 5-BUTTON SERIES VEHICLE SECURITY SYSTEM INSTALLATION MANUAL

6 RELAY SYSTEM 5-BUTTON SERIES VEHICLE SECURITY SYSTEM INSTALLATION MANUAL 6 REAY SYSTEM 5-BUTTON SERIES VEHICE SECURITY SYSTEM INSTAATION MANUA Before you begin the installation Read the INSTRUCTIONS! Always use a multi-meter when verifying vehicle wiring. Before mounting the

More information

CS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS

CS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS CS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an On-Guard Series Remote Alarm System by Crimestopper Security Products

More information

Remote Start with Keyless Entry Installation Guide CA 5051

Remote Start with Keyless Entry Installation Guide CA 5051 PROFESSIONAL SERIES Remote Start with Keyless Entry Installation Guide CA 5051 2010 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...

More information

CA 421 Installation Instructions

CA 421 Installation Instructions CA 421 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components

More information

Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide for models: ca5153 ca5153sst

Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide for models: ca5153 ca5153sst PROFESSIONAL SERIES Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide for models: ca5153 ca5153sst 2012 Audiovox Electronics Corporation. All rights reserved. 1 Table of

More information

CS-2001FC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION

CS-2001FC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CS-2001FC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc.

More information

CS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION

CS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc. This booklet

More information

Manual - Inside Front Cover (Blank)

Manual - Inside Front Cover (Blank) FRONT COVER Manual - Inside Front Cover (Blank) Table of Contents Important Information... 2 Recommended Installation Tools... 2 Recommended Procecures... 2 Wiring Diagram... 3 14 Pin Connector...4 Installation

More information

CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM

CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM Installation And Operation Manual MEGATRONIX VAN NUYS, CA U.S.A. CP634 1 REMOTE CONTROL CONVENIENT SYSTEM INSTALLATION & OPERATION INSTRUCTIONS INTRODUCTION

More information

INSTALLATION GUIDE OWNER S GUIDE

INSTALLATION GUIDE OWNER S GUIDE INSTALLATION GUIDE OWNER S GUIDE SECURITY SYSTEM PRO-SERIES 6002 CONTENTS System Features... 1-2 System Components... 2 Technical Assistance... 2 Before You Begin... 2 Precautions... 2-3 Making Connections...

More information

MEGA 462 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS WIRING DIAGRAM. White. H1 5 Pin White. H6 2 Pin White.

MEGA 462 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS WIRING DIAGRAM. White. H1 5 Pin White. H6 2 Pin White. MEGA 462 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS WIRING DIAGRAM H7/1 Green : (-) 200mA Pulse H7 3 Pin H7/3 Blue : (-) 200mA Unlock White LED Indicator Valet Switch H6 2 Pin

More information

DLRM DLRM

DLRM DLRM Table of Contents 1. Before You Begin.........................................................Page 1 2. Installation Tips..........................................................Page 2 3. Mounting Components

More information

*IMPORTANT INFORMATION:

*IMPORTANT INFORMATION: CS-2003DC REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc. This system

More information

Model APS-101N Installation Manual

Model APS-101N Installation Manual Programmable Features Model APS-101N Installation Manual Select By Operating Transmitter Press Lock Button Press Unlock Button Siren Indications 1 Chirp 2 Chirps Factory Default 1) Arming Method Passive

More information

CS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION

CS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CS-2000 Series III REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an On-Guard Series Remote Alarm System by Crimestopper Security Products

More information

INSTALLATION GUIDE Table of Contents

INSTALLATION GUIDE Table of Contents CT-3100 Automatic transmission remote engine starter systems. What s included..2 INSTALLATION GUIDE Table of Contents Door lock toggle mode..... 4 Notice...2 Installation points to remember. 2 Features..2

More information

INSTALLATION GUIDE. FCC ID NOTICE

INSTALLATION GUIDE.  FCC ID NOTICE REV.5 RS. ADVANCED REMOTE STARTER INSTALLATION GUIDE www.security.soundstream.com FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This

More information

INSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer.

INSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. INSTALLATION MANUAL SL- 3 3-Channel Security with Keyless Entry System This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. For Warranty information:

More information

FS-22 and FS-32 KEYLESS ENTRY and ALARM SYSTEM INSTALLATION INSTRUCTIONS

FS-22 and FS-32 KEYLESS ENTRY and ALARM SYSTEM INSTALLATION INSTRUCTIONS FS-22 and FS-32 KEYLESS ENTRY and ALARM SYSTEM INSTALLATION INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Remote Keyless Entry and Alarm System by Crimestopper Security Products Inc. This

More information

INSTALLATION MANUAL 601-S INFORMATION.) 8. REMOVE DOME LIGHT FUSE TO PRE- VENT BATTERY DRAIN.

INSTALLATION MANUAL 601-S INFORMATION.) 8. REMOVE DOME LIGHT FUSE TO PRE- VENT BATTERY DRAIN. FOR NEGATIVE PARKING LIGHTS (MOST JAPANESE VEHICLES) FOR POSITIVE PARKING LIGHTS TRUNK RELEASE CIRCUIT DIAGRAM: OUT TO TRUNK 12V 2nd CHANNEL AUXILIARY (GRAY WIRE) 86 a 85 If the power trunk release requires

More information

Remote Start Installation Guide ca 4552

Remote Start Installation Guide ca 4552 PROFESSIONAL SERIES Remote Start Installation Guide ca 4552 ca4552. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Before You Begin... 3 Wire Connection Guide... 4 4 Pin Main Harness...

More information

12V PROGRAMMABLE POWER OUT

12V PROGRAMMABLE POWER OUT Page 1 ACCESSORIES STARTER IGNITION BATTERY WIRES SIDE VIEW BLUE RED YELLOW 30 A 10 A BLUE / WHITE YELLOW WHITE / BLUE WHITE / DOOR TRIGGER See opt. 16 DOOR TRIGGER (input positive) See opt. 16 PARKING

More information

Button 1 Button 2. Button 3 Button 4. Programmed Remote Transmitter. Button Function Condition

Button 1 Button 2. Button 3 Button 4. Programmed Remote Transmitter. Button Function Condition WWW.STELLAR.COM Button Function Condition 1 a. Arm and lock doors b. Car finder with sound c. Temporary stop alarm from sounding d. Remote lock doors 1 for 2 sec. Panic Anytime a. Alarm is disarmed b.

More information

CS-2002DPII With Data Port Technology

CS-2002DPII With Data Port Technology CS-2002DPII With Data Port Technology REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an On-Guard Remote Alarm System with DP Technology

More information

FS-30 2-WAY REMOTE CONTROL ALARM SYSTEM INSTALLATION INSTRUCTIONS

FS-30 2-WAY REMOTE CONTROL ALARM SYSTEM INSTALLATION INSTRUCTIONS FS- 2-WAY REMOTE CONTROL ALARM SYSTEM INSTALLATION INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an Remote Alarm System by Crimestopper Security Products Inc. This booklet contains the information

More information

Diablo 2 /AMX 68/AT-58 Installation Manual 3/31/99

Diablo 2 /AMX 68/AT-58 Installation Manual 3/31/99 1 Table of Contents Required Installation Tools... 2 Important Information... 2 Wiring Diagram.... 3 14 Pin Con nec tor... 4 Starter Dis able Relay...4 Installation Procedures...5 Control Unit... 5 Antenna...

More information

DLKEK3HN INSTALLATION INSTRUCTIONS

DLKEK3HN INSTALLATION INSTRUCTIONS DLKEK3HN INDEX: INSTALLATION INSTRUCTIONS WIRING INSTRUCTIONS... PG 2-5 LED STATUS INDICATOR... PG 6 VALET/OVERRIDE BUTTON... PG 6 SHOCK SENSOR... PG 7 PROGRAMMABLE JUMPER-PINS... PG 7 PROGRAMMING REMOTE

More information

CA-510a Installation Instructions

CA-510a Installation Instructions CA-510a Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide. ca 5152

Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide. ca 5152 PROFESSIONAL SERIES Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide ca 5152 1 Table of Contents Before You Begin... 3 Wire Connection Guide... 4 11 Pin Main Harness...

More information

CSI-400 Installation Instructions

CSI-400 Installation Instructions CSI-400 Installation Instructions Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces

More information

CS-2004 WDC. Remote Control Alarm System with CoolGlow & SecurWatch INSTALLATION & OPERATING INSTRUCTIONS

CS-2004 WDC. Remote Control Alarm System with CoolGlow & SecurWatch INSTALLATION & OPERATING INSTRUCTIONS CS-2004 WDC Remote Control Alarm System with CoolGlow & SecurWatch INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION: CONGRATULATIONS on your choice of a Remote Alarm System by Crimestopper Security Products

More information

CS-2003DC & CS-2003DC Series II

CS-2003DC & CS-2003DC Series II CS-2003DC & CS-2003DC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security

More information

INSTALLATION GUIDE OWNER S GUIDE

INSTALLATION GUIDE OWNER S GUIDE INSTALLATION GUIDE OWNER S GUIDE SECURITY SYSTEM PRO-SERIES 7002 CONTENTS System Features... 1-2 System Components... 2 Technical Assistance... 2 Before You Begin... 2 Precautions... 3 Making Connections...

More information

VEHICLE SECURITY SYSTEM INSTALLATION MANUAL

VEHICLE SECURITY SYSTEM INSTALLATION MANUAL VEHICLE SECURITY SYSTEM WITH REMOTE START & NETWORK INTERFACE INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! Before You Begin This system is intended

More information

INSTALLATION MANUAL. Remote Mobile Security System. Model: PL30

INSTALLATION MANUAL. Remote Mobile Security System. Model: PL30 Remote Mobile Security System INSTALLATION MANUAL Model: PL30 Copyright 1998 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be

More information

KE 680 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM DOOR LOCK RELAYS ON-BOARD. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A.

KE 680 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM DOOR LOCK RELAYS ON-BOARD. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. KE 680 DELUE 4-CHANNEL KEYLESS ENTRY SYSTEM DOOR LOCK RELAYS ON-BOARD Installation And Operation Manual MEGATRONI CALIFORNIA, U.S.A. KE 680 1 INSTALLATION DIAGRAM H8: 10 Pin White Mini Connector H8 10

More information

REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION

REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CS-2001FC REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc. This booklet

More information

Model APS-510C Installation Manual Remote Control Vehicle Security System

Model APS-510C Installation Manual Remote Control Vehicle Security System Model APS-510C Installation Manual Remote Control Vehicle Security System Table Of Contents: Before You Begin Page 2 Wire Harnesses Quick View Page 3 Mounting Of The Major Components Page 4 8 Pin Power

More information

Remote Start Installation Guide CA 4051

Remote Start Installation Guide CA 4051 PROFESSIONAL SERIES Remote Start Installation Guide CA 4051 2010 Audiovox Electronics Corporation. All rights reserved. 1 Before You Begin... 3 Wire Connection Guide... 4 4 Pin Main Harness... 5 3 Pin

More information

MEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 INSTALL 1

MEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 INSTALL 1 MEGA 2500 2-WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM Installation Manual MEGATRONI CALIFORNIA, USA MEGA 2500 INSTALL 1 MEGA 2500 INSTALL 2 INSTALLATION DIAGRAM H8: 10 Pin White Mini Connector H8 10

More information

INSTALLATION MANUAL. Remote Mobile Security System. Model: PL50

INSTALLATION MANUAL. Remote Mobile Security System. Model: PL50 Remote Mobile Security System INSTALLATION MANUAL Model: PL50 Copyright 2000 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be

More information

OCT/21/02 MEGA 670L DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A.

OCT/21/02 MEGA 670L DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. OCT/21/02 MEGA 670L DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. MEGA 670 1 MEGA 670 2 OCT/21/02 OCT/21/02 WIRING DIAGRAM H7: 10 Pin White

More information

INSTALLATION MANUAL. Model: PLUS Vehicle Security

INSTALLATION MANUAL. Model: PLUS Vehicle Security R Vehicle Security INSTALLATION MANUAL Model: PLUS-5000 Copyright 1999 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be a Registered

More information

VEHICLE SECURITY SYSTEM

VEHICLE SECURITY SYSTEM A10 SERIES VEHICLE SECURITY SYSTEM PRODUCT MANUAL Limited Lifetime Warranty This vehicle security system is warranted to the original purchaser, to be free from defects in material and workmanship. The

More information

Security and Remote Start Installation Guide for models: ca6553 ca6553sst

Security and Remote Start Installation Guide for models: ca6553 ca6553sst PROFESSIONAL SERIES Security and Remote Start Installation Guide for models: ca6553 ca6553sst 2012 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 4 Wire

More information

Model APS-25N Installation Manual

Model APS-25N Installation Manual Model APS-25N Installation Manual Note : When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver s do pin switch in der to begin the passive arming sequence. RF Programmable

More information

RA2 Installation Manual Rev. B

RA2 Installation Manual Rev. B Important Information Required Installation Tools Voltmeter Wire Strippers Electric Drill & Bits Phillips Screwdriver Convoluted Tubing * Solder Gun * Wire Crimpers Shrink Tube or Electrical Tape * Optional

More information

Model APS-25CH Installation Manual

Model APS-25CH Installation Manual Model APS-25CH Installation Manual Note : When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver s do pin switch in der to begin the passive arming sequence. RF Programmable

More information

Security and Remote Start Installation Guide for models: ca 6552 ca 6552 SST

Security and Remote Start Installation Guide for models: ca 6552 ca 6552 SST PROFESSIONAL SERIES Security and Remote Start Installation Guide for models: ca 6552 ca 6552 SST ca6552/6552sst. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You

More information

CS-2002DC & CS-2002DC Series II

CS-2002DC & CS-2002DC Series II CS-2002DC & CS-2002DC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security

More information

RF-425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL (FOR AUTHORIZED DEALERS ONLY)

RF-425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL (FOR AUTHORIZED DEALERS ONLY) RF-425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL (FOR AUTHORIZED DEALERS ONLY) THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY 1 BLUE...TRUNK/HOOD TRIGGER (-) INPUT BLACK/BLUE...4TH

More information

FM SECURITY AND REMOTE START SYSTEM

FM SECURITY AND REMOTE START SYSTEM FM SECURITY AND REMOTE START SYSTEM INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! This system is intended for installation on vehicles equipped with

More information

Security and Remote Start Installation Guide for models: ca6554

Security and Remote Start Installation Guide for models: ca6554 PROFESSIONAL SERIES Security and Remote Start Installation Guide for models: ca6554 2014 Voxx Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin...4 Wire Connection Guide...5

More information

Red #22 Power. Red #14. Brown #18. Ign/Acc/Start. White#14. Tachometer Foot-Brake Door Pin Pos Trunk/Hatch (open) (-) while running Lock Arm

Red #22 Power. Red #14. Brown #18. Ign/Acc/Start. White#14. Tachometer Foot-Brake Door Pin Pos Trunk/Hatch (open) (-) while running Lock Arm E400 RFK1004 WIRING / CONNECTION GUIDE AUTOMATIC & MANUAL TRANSMISSION REMOTE STARTER & ALARM QUICK INSTALLATION GUIDE GUIDE # 69151 Power (utility) Red #22 OUTPUT INPUT Power Red #14 1 Yellow #14 Starter

More information

OWNER S GUIDE REMOTE START. Part Number: REV A 2010 HYUNDAI MOTOR AMERICA

OWNER S GUIDE REMOTE START. Part Number: REV A 2010 HYUNDAI MOTOR AMERICA OWNER S GUIDE Part Number: 4280279 REV A 2010 HYUNDAI MOTOR AMERICA REMOTE START REMOTE START OWNER S GUIDE INTRODUCTION Congratulations on your purchase of a Hyundai Remote Start System with Deluxe Vehicle

More information

AviStart 6500 Installation Manual

AviStart 6500 Installation Manual Table of Contents Important Information... 1 Recommended Installation Tools... 1 Recommended Procedures... 1 Main Wiring Diagrams.... 2 Pin Connectors... 5 Installation Procedures...7 Control Unit... 7

More information

Model PRO 9246CH Installation Manual

Model PRO 9246CH Installation Manual Model PRO 9246CH Installation Manual PRE-INSTALLATION NOTES: RF Programmable Features : Feature Selection 1 Flash 2 Flash 3 Flash Default 1st Do L/UL 1 Sec. 3.5 Sec. 1 Sec L, Dbl. U/L 1 Sec. 2nd Accy Lock

More information

Remote Vehicle Control System. Keyless Entry and Convenience System

Remote Vehicle Control System. Keyless Entry and Convenience System 1 Remote Vehicle Control System PC 6100 TM Owner's Manual Keyless Entry and Convenience System IMPORTANT NOTE: The operation of the Power Code as described in this manual is applicable to most vehicles.

More information

REC-11+ REMOTE RECEIVER UNIT

REC-11+ REMOTE RECEIVER UNIT Resetting The Programmable Features The installer may quickly and easily return all 17 programmable features back to the factory settings. Changing individual features were explained in detail in the previous

More information

ADVANCED KEYLESS ENTRY SYSTEM INSTALL GUIDE.

ADVANCED KEYLESS ENTRY SYSTEM INSTALL GUIDE. REV.2009.04.10 KE-6 ADVANCED KEYLESS ENTRY SYSTEM TM INSTALL GUIDE www.ultrastarters.com FCC ID NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:

More information

VS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1

VS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1 VS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1 VS 315 2 INSTALLATION We recommend insulating all your soldered or crimped connections

More information

RS-351-EDP. Installation Guide

RS-351-EDP. Installation Guide RS-351-EDP Keyless Entry & Remote Start Installation Guide June 25, 2013 Temporary cover. Color cover is in a separate file. Table Of Contents Installation Considerations... 3 6 Pin Main Wire Harness...

More information

2005 Directed Electronics, Inc. Vista, CA N412V 01-05

2005 Directed Electronics, Inc. Vista, CA N412V 01-05 Model 211HV Installation Guide NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may

More information

VS 655 DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 655 1

VS 655 DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 655 1 VS 655 DELUXE 4-CHANNEL CAR ALARM SECURITY SYSTEM Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 655 1 VS 655 2 INSTALLATION DIAGRAM H8: 10 Pin White Mini Connector H8 10 Pin White

More information

AL-100DP Full-Feature Vehicle Security System for Factory-Equipped Remote Keyless Entry Transmitters Owner s Guide

AL-100DP Full-Feature Vehicle Security System for Factory-Equipped Remote Keyless Entry Transmitters Owner s Guide This device complies with FCC Rules part 15. Operation is subject to the following two conditions, (1) This device may not cause harmful interference and, (2) This device must accept any interference that

More information

AUTOMATIC TRANSMISSION ONLY! Technical Support: ext 1 Warning!!

AUTOMATIC TRANSMISSION ONLY!  Technical Support: ext 1 Warning!! REV.2006.04 INSTALL GUIDE AUTOMATIC TRANSMISSION ONLY! www.ultrastarters.com Technical Support: 877-598-2100 ext 1 support@ultrastarters.com Warning!! The system must be placed into Service Mode before

More information

Maxx 3 Installation Guide

Maxx 3 Installation Guide Maxx 3 Installation Guide 2002 Directed Electronics, Inc. Vista, CA N840003 4-02 Table of Contents Important Information....................................................... 3 System Components........................................................

More information

Advanced Remote Vehicle Starting System

Advanced Remote Vehicle Starting System INSTALLATION GUIDE 1600 Advanced Remote Vehicle Starting System 1600M AUTOMATIC AND MANUAL TRANSMISSION MODELS WWW.ULTRASTARTERS.COM See website for a full size printable version of this manual. WARNING!!

More information

CS-2000DPII TW2 With 2-Way Data Port Technology 2-WAY REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS

CS-2000DPII TW2 With 2-Way Data Port Technology 2-WAY REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS CS-2000DPII TW2 With 2-Way Data Port Technology 2-WAY REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an On-Guard Remote Alarm System by

More information

Installation Manual By Firstech LLC, Version: 1.1

Installation Manual By Firstech LLC, Version: 1.1 Installation Manual By Firstech LLC, Version: 1.1 Applicable to the following remote start system: CM800-S Auto Only Starter Control Module This device complies with Part 15 of the FCC rules. Operation

More information

Covers All 35xx Series Advanced 2-Way Remote Starters. Technical Support: ext 0

Covers All 35xx Series Advanced 2-Way Remote Starters.   Technical Support: ext 0 INSTALL GUIDE Covers All 35xx Series Advanced 2-Way Remote Starters www.ultrastarters.com Technical Support: 866-698-5872 ext 0 support@ultrastarters.com Warning!! The system must be placed into Service

More information

CA 180 Owner's Manual

CA 180 Owner's Manual Remote Vehicle Control System CA 180 Owner's Manual Deluxe Vehicle Security System with Two Way Confirming Dot Matrix Remote Control IMPORTANT NOTE: The operation of the Security and Convenience System

More information

MEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Operation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 OPERATE 1

MEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Operation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 OPERATE 1 MEGA 2500 2-WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM Operation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 OPERATE 1 MEGA 2500 OPERATE 2 OPERATION: A. TRANSMITTER OPERATION: Transmitter Button System

More information

INSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer.

INSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. INSTALLATION MANUAL SL- 72 Two-Way 5-Channel 915Mhz Remote Start Security System This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. For Warranty

More information

MEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Operation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 OPERATE 1

MEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Operation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 OPERATE 1 MEGA 2500 2-WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM Operation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 OPERATE 1 OPERATION: A. TRANSMITTER OPERATION: Transmitter Button System Function Remark Lock

More information

Model PRO 9644a Installation Manual

Model PRO 9644a Installation Manual Model PRO 9644a Installation Manual SELECTABLE FEATURES Note: The method of manual override can either be selected to operate from the valet switch operate as custom code. Be certain to place a check mark

More information