AIR PREPARATION PRODUCTS

Transcription

1 72 Series Modular Components Quikclamp Maximum Pressure: 17 bar (250 psig) Maximum Temperature: 65 C (150 F) Use with all Excelon 72 Products to provide modular installation capability. Flanges on the products slide into V grooves in the Quikclamp. Two face-sealing o-rings in the Quikclamp provide a positive seal when the clamp is closed and the captive screw is tightened. Tighten screw with a 3 mm hex wrench or a T15 Torx wrench. Quikclamp Service Kit (contains 2 nitrile o-rings): A Quikclamp adds 0.26" (6.5 mm) to the overall length of a combination unit. Part Number: Quikclamp Wall Mounting Bracket Use with the Quikclamp to provide secure mounting to a wall, machine panel or other flat surface. Use 3/16" (5 mm) screws to mount bracket to wall (59) 0.59 (15) 2.91 (7) Part Number: Quikmount Pipe Adapters Use with the Quikclamp to provide threaded connections to the system piping. A pipe adapter adds 0.63" (16 mm) to the overall length of a combination unit. Quikclamp and Wall Mounting Bracket See Quikclamp paragraph for descriptions and dimensions. Use 3/16" (5 mm) screws to mount bracket to wall. Wall Part Number: Porting Block Installs between two Quikclamps to provide three additional 1/" outlets for auxiliary air. A Porting Block adds 1.13" (28.5 mm) to the overall length of a combination unit. Sub-base Mounted Pressure Switch Monitors air pressure and provides an electrical output when the pressure drops below or exceeds an adjustable preset pressure. Installs between two Quikclamps. Also provides two additional 1/" outlets for auxiliary air. P 1 max: 250 psig (17 bar) Temperature: 1 to 150 F (-10 to 65 C) Adjustable 30 to 150 psig (2 to 10 bar). Shipped from factory preset at 90 psig (6.3 bar) Max. Voltage: Max. Current: 20 V a.c./d.c. 5 Amp Hysteresis at Midpoint: 12% A Sub-base Mounted Pressure Switch adds 1.13" (29 mm) to the overall length of a combination unit. Auxiliary Port Threads Part Number Manifold Block Installs with Quikclamps. Ports are threaded 3/8" pipe to provide manifolding capability for up to three components (5) Port Size and Thread Part Number (Quantity of 1) 1/" PTF /8" PTF Auxiliary Port Size & Thread Part Number 1/" NPT /" IS0 G /" PTF /" ISO G Transition Connector Enables connection of Excelon 72 to 7 units. Typically this will allow F7C/H high grade coalescing filters to be flow matched with R72 regulators. 1/" ISO G /8" ISO G Replacement Pressure Switch 1.98 (50) Use only with pressure switch sub-base. Cannot be used with the standard porting block. Part Number: Side Port Threads Part Number 3/8" PTF /8" ISO G Part Number: APP-135

2 73 and 7 Series Modular Components Quikclamp Use with all 73 and 7 Series Products to provide modular installation capability. Flanges on the products slide into V grooves in the Quikclamp. Two face-sealing o-rings in the Quikclamp provide a positive seal when the clamp is closed and the captive screw is tightened. A Quikclamp adds 0.5" (13.6 mm) to the overall length of a combination unit. Tighten screw with a 5/32" ( mm) hex or T25 Torx wrench. (30 in. lbs. Torque) Material: Zinc Quikclamp part number: O-ring kit part number: Quikmount Pipe Adapters Use with the Quikclamp to provide threaded connections to the system piping. Each pipe adapter adds 0.71" (18 mm) to the overall length of a combination unit (each kit contains one adapter). Material: Aluminum Part number 1) Port size and (Qty) thread /" PTF /8" PTF /2" PTF /" PTF /" ISO G /8" ISO G /2" ISO G /" ISO G Quikclamp Wall Mounting Bracket Use with the Quikclamp to provide secure mounting to a wall, machine panel or other flat surface. Use No. 12 (6 mm) screws to mount bracket to wall (2) 3.25 (83).00 (102) Material: Zinc Part number: Quikclamp and Wall Mounting Bracket See preceding paragraphs for descriptions and dimensions. Wall Material: Zinc Part number: L7 1 quart Porting Block Installs between two Quikclamps to provide three additional 1/" outlets for auxiliary air. A Porting Block adds 1.30" (33 mm) to the overall length of a combination unit. Material: Zinc Part number Auxiliary port size and thread Replacement Pressure Switch Use only with the pressure switch subbase. Cannot be used with the standard porting block. Material: Aluminum Pressure switch part number: Subbase Mounted Pressure Switch Monitors air pressure and provides an electrical output when the pressure drops below or exceeds an adjustable preset pressure. Installs between two Quikclamps. Also provides three additional 1/" outlets for auxiliary air. A Subbase Mounted Pressure Switch adds 1.30" (33 mm) to the overall length of a combination unit. Specifications Maximum Pressure: 300 psig (20 bar) Maximum Temperature: 175 F (80 C) Adjustable Range: 30 to150 psig (2 to 10 bar) Shipped from factory preset at 90 psig (6.2 bar). Maximum Voltage: 20V ac/dc Maximum Current: 5 Amp Hysteresis at Midpoint: 12% Materials: Zinc subbase, Aluminum switch Auxiliary port Part number thread /" PTF /" ISO G Manifold Block Installs with Quikclamps. Ports are threaded 3/" pipe to provide manifolding capability for up to three components (57) 3.15 (80) Material: Zinc Part number Side port threads /" PTF /"ISO Rc Transition Connector Enables connection of Excelon 72 to 7 units. A transition connector adds 0.06" (1.5mm) to the overall length of a combination unit. Material: Aluminum Part Number: /" PTF /" IS0 G APP-136

3 6 Series Modular Components Single Yoke.13 (105)* 1.6 (37) 2.91 (7) * 3/= 6.18 (157) 1/ Y6A-2AA-N1N 3/8 Y6A-3AA-N1N 1/2 Y6A-AA-N1N 3/ Y6A-6AA-N1N Double Yoke 7.28 (185)* 1.6 (37) 2.91 (7) * 3/ = 9.33 (237) 1/ Y6A-2AA-N2N 3/8 Y6A-3AA-N2N 1/2 Y6A-AA-N2N 3/ Y6A-6AA-N2N Yoke Connector Porting Block Adjustable Pressure Switch End Connector (2) 1/ outlets (1) 3/8 outlet G 3 / (1.5) psi (2 10 bar) adjustable Porting block mounted DIN 3650 form C connector For use with end mounted porting block 1/2 or 3/ over porting 1.38 (35) G 1 / 1.61 (1) 3.78 (96) 1.2 (26) P 1 max. = 250 psi (17 bar) T max. = 175 F (80 C) PTF ISO G 1.61 (1) P 1 max. = 250 psi (17 bar) T max. = 175 F (80 C) I max. = 5 A V max. = 20 V Reset differential = 15 psi (1 bar) nominal 1/ PTF 3/ PTF 1/ ISO G 3/ ISO G APP-137

4 68 Series Modular Components Alternative 68 Series Yoke Assembly Models Shut-Off Valve and Porting Block No shut-off valve, No porting block With shut-off valve, No porting block With shut-off valve, With porting block No shut-off valve, With porting block Port Size Substitute A B E F Substitute 3/" 6 1" 8 1 1/" A 1 1/2" B Threads PTF ISO Rc taper ISO G parallel Substitute A B G Y68H - HHN - HHH Wall Mounting Bracket Without With Yoke Substitute N B Substitute Single 1 Double 2 Triple 3 Shut-Off Valve Type 2-port/2-position, Padlocks open or closed, No exhaust, Black handle 3-port/2-position, Padlocks open or closed, Unthreaded exhaust, Black handle 3-port/2-position, Not lockable, Threaded exhaust, Black handle 3-port/2-position, Padlocks closed only, Unthreaded exhaust, Yellow handle 2-port/2-position, Not lockable, No exhaust, Black handle No shut-off valve Substitute A C D E * G N * Meets OSHA requirements. APP-138

5 68 Series Modular Components Yoke Connecting Kit Comprising seal, screws and nuts. Part Number Mounting Bracket Brackets slip over end connectors and are bolted to Yoke Assembly with nuts and screws provided. Note: Each kit contains 6 screws (2 x 80 mm and x 35 mm) and nuts. Part Number Single Yoke 2.13 (5).92 (125).25 (108) Part Number: Single Yoke Assembly Double Yoke Assembly 12. (315) 2.13 (5).26 (108) Port Size NPT 1/2 Y68A-AN-N2N NPT 3/ Y68A-6AN-N2N NPT 1 Y68A-8AN-N2N NPT 1-1/ Y68A-AAN-N2N NPT 1-1/2 Y68A-BAN-N2N 7.8 (190) 1/2" ported yoke /" ported yoke " ported yoke /" ported yoke /2" ported yoke N/A 2.13 (5).25 (108) Port Size NPT 1/2 Y68A-AN-N1N NPT 3/ Y68A-6AN-N1N NPT 1 Y68A-8AN-N1N NPT 1-1/ Y68A-AAN-N1N NPT 1-1/2 Y68A-BAN-N1N APP-139

6 Filter Accessories F F17 3/", 1" Ports: /", 1-1/2" Ports: F F07, F39 Bracket ( ) 1.59 (0) 1.33 (3) 2.06 (52) 0.29 (7) 1.02 (26) 0.93 (2) 1.3 (3) 0.22 (6) F17, F6 Bracket ( , ) 5.13 (130) 3.00 (76) 3.19 (81) 1.00 (25) 1.69 (3) 0.3 (9) Dia. F22 Bracket ( ) F F6 3/", 1" Ports: /", 1-1/2" Ports: (90) 1.22 (31).80 (122).06 (103) 0.33 (8.5) 2.05 (52) F F6 Bracket (750-50) 0.32 (8.2) 3.35 (85) 5.63 (13).9 (11) 3.66 (93) 1.20 (30.5) 1.89 (8).33 (110) 0.3 (11) 0.57 (1.5) APP-10

7 Filter Accessories F68 1/2", 3/", 1", 1-1/" Ports: /2" Ports: Not Available F F73 Wall Bracket Electric service indicator Provides electrical signal when element needs to be replaced. Rated NEMA R F68 Bracket ( ) 3.9 (100) 2.8 (72) 1.97 (50) (190) 0.59 (15) 7.8 (190)* 8.19 (208)* * Add 0.39" (10) for 1-1/" ported yokes. F72 Bracket (22-50) F73 Bracket (2-50) 0.33 (8.5) F7 Visual service indicator Turns from green to red when element needs to be replaced. Electric service indicator Rated NEMA Provides electrical signal when element needs to be replaced. Visual service indicator Turns from green to red when element needs to be replaced R (5) 0.16 () (5) 0.79 (20) 0.7 (12) 1.5 (39) 2.36 (60) F7 Bracket (32-50) 2.88 (73) 3.25 (83) 0.20 (5) 0.16 () 1.6 (37) 1.00 (25) 0.77 (20) 0.28 (7) Port L C 0.16 () Port L C 0.7 (19) 2.37 (60) 1.10 (28) (8) 2.6 (67) 2.0 (61) 1.97 (50) 2.0 (61) APP-11

8 Regulator Accessories R05 Plastic panel nut R06 for R06 with plastic bonnet for R06 with brass bonnet Bracket and plastic nut: Plastic nut: Metal nut: Bracket and metal nut: Metal nut: R06, R07 Bracket ( ) 2.7 (63) 0.29 (7) 0.38 (10) 0.93 (2) 0.63 (16) 0.22 (6) 1.63 (1) R06 Bracket for Brass Bonnet ( ) Tamper resistant knob kit (35) 0.63 (16) 0.35 (9) 0.22 (6) 0.38 (10) 1.0 (25) 2.1 (61) 1.63 (1) R07 with plastic nut Bracket and plastic nut: Plastic nut: Metal nut: Tamper resistant knob kit R17 with plastic nut Bracket and metal nut: Metal nut: R17 Bracket (5570-0) Tamper resistant seal wire (81) Pipe C L.50 (11) R18 Muffler 3/ PTF: MB006A R 3/: MB006B 0.28 (7) 0.5 (1) 3.50 (89) 1.08 (27) 1.19 (30) 0.56 (1) APP-12

9 Regulator Accessories R22 R2 Stainless steel wall bracket (neck mount) with metal nut Stainless steel wall bracket and metal nut: Metal nut: Bracket and metal nut: Bracket: Plastic nut: Metal nut: R22 Bracket ( ) 1.22 (31) 3.18 (81).17 (106) 3.39 (86) 2.05 (52) 0.33 (8.5) R22 Neck Bracket ( ) 3.11 (79) 0.98 (25) 2.95 (75) 2.13 (5) 0.33 (8.5) 2.00 (50) Reducing bushing for gauge ports 3/8 to 1/ PTF: /2 to 1/ PTF: R1/ to G1/8: R3/8 to G1/8: R1/2 to G1/8: R2 Bracket ( ) Tamper resistant cap (77.5) 1.73 () 3.05 (77.5) 1.8 (6) 1.26 (32) 2.91 (7) 3.23 (82) 1.73 () 1.8 (6) 0.2 (5) 1.26 (32) 0.2 (5) 2.6 (67) 2.95 (75) 1/", 3/8", 1/2" Ports 3/", 1", 1-1/" Ports APP-13

10 Regulator Accessories R38 Aluminum wall bracket and nut: Aluminum nut: R0 R1 R3 Plastic adjusting knob with metal nut Stainless steel wall bracket and nut: Stainless steel nut: Bracket and metal nut: Plastic nut: Metal nut: R38 Bracket ( ) 2.95 (75) 1.10 (28) 2.95 (75) 2.13 (5) 0.3 (8.5) Tamper resistant seal wire R0, R1, R3 Bracket ( ) 2.5 (6) R for R with plastic bonnet Bracket and plastic nut: Plastic nut: Metal nut: (38) 2.75 (70) for R with brass bonnet R Bracket ( ) R Bracket for Brass Bonnet ( ) 2.7 (63) 0.63 (16) 1.63 (1) 0.29 (7) 0.38 (10) 0.93 (2) 0.22 (6) 0.35 (9) 1.38 (35) 0.38 (10) 2.1 (61) 1.63 (1) 0.63 (16) Bracket and metal nut: Metal nut: (38) 1.0 (25) 1.5 (38) 0.66 (17) 0.27 (7) Tamper resistant knob (25) 0.22 (6) APP-1

11 Regulator Accessories R6 Metal panel nut Tamper resistant cover and wire. Install over knob to help prevent tampering of pressure setting. Use up to padlocks with 5/16" (8mm) diameter shackle to secure cover. Lockout hasp may also be used Cover and wire: Wire: R6 Bracket (750-50) 0.32 (8.2) 3.35 (85) 5.63 (13).9 (11) 1.20 (30.5) 1.89 (8) 3.66 (93).33 (110) 0.3 (11) 0.57 (1.5) R68 1/2", 3/", 1", 1-1/" Ports: /2" Ports: Not Available R68 Bracket ( ) 2.8 (72) Tamper resistant cover and wire. Install over knob to help prevent tampering of pressure setting. Use up to padlocks with 5/16" (8mm) diameter shackle to secure cover. Lockout hasp may also be used. Cover and wire: Wire: (100) 1.97 (50) (190) 0.59 (15) 0.33 (8.5) 7.8 (190)* R (208)* * Add 0.39" (10) for 1-1/" ported yokes. R72 Bracket (22-50) R72 Neck Bracket ( ) /plastic nut Tamper resistant cover and wire. Install over knob to help prevent tampering of pressure setting. Use up to 2 padlocks with 5/16 (8mm) diameter shackle to secure cover. Lockout hasp may also be used. Bracket and plastic nut: Plastic nut: Metal Nut: Cover and wire: Wire: (5) 0.16 () 1.77 (5) 0.79 (20) 0.7 (12) 2.36 (60) 1.9 (9) 1.2 (30) 2.36 (60) 0.3 (8) (39) 1.0 (25).60 (15) 0.2 () 0.3 (8) APP-15

12 Regulator Accessories R73 /metal nut Tamper resistant cover and wire. Install over knob to help prevent tampering of pressure setting. Use up to padlocks with 5/16" (8mm) diameter shackle to secure cover. Lockout hasp may also be used Bracket and metal nut: Metal Nut: Plastic Nut: Cover and wire: Wire: R73 Bracket (2-50) 0.28 (7) 0.16 () 0.7 (19) 2.37 (60) 1.10 (28) (8) 2.6 (67) 2.0 (61) R73 Neck Bracket (61-50) 1.5 (38) 1.0 (25) 2.5 (6) 1.5 (38) 1.5 (38) 2.75 (70) 0.66 (17) 0.27 (7) Allows use of up to 6 padlocks with 5/16" (8mm) diameter shackle. R7 Bracket (32-50) R7 Neck Bracket (368-51) 2.88 (73) 3.5 (89) R (83) 2.06 (52) 3.37 (86) /metal nut Tamper resistant cover and wire. Install over knob to help prevent tampering of pressure setting. Use up to padlocks with 5/16" (8mm) diameter shackle to secure cover. Lockout hasp may also be used. Bracket and metal nut: Metal Nut: Cover and wire: Wire: (5) 0.16 () 0.77 (20) 1.6 (37) 1.00 (25) 1.97 (50) 2.0 (61) 1.38 (35) 0.9 (23) 2.2 (56) 0.95 (2) 0.28 (7) Allows use of up to 6 padlocks with 5/16" (8mm) diameter shackle. APP-16

13 Regulator Accessories R81 R82 R83 R Pipe plug, hex socket 1/ PTF: Nipple 1/ PTF male: Cylinder connector, nitrogen service, RH external thread CGA No. 580: R81, R82, R83, R8 Bracket ( ) 0.28 (7) Typ 1.03 (26) 0.5 (13) 2 (51) 0.31 (8) Typ 2.75 (70) 0.31 (8) Cylinder connector, carbon dioxide service, RH internal thread CGA No 320: With 2.25" (57mm) long nipple: Replacement gasket: APP-17

14 Regulator Accessories R91 with plastic nut Tamper resistant knob Bracket and plastic nut: Plastic nut: Metal nut: R91 Bracket ( ) 2.7 (63) 0.29 (7) 0.38 (10) 0.93 (2) 0.63 (16) 0.22 (6) 1.63 (1) Bracket Bracket (Units with 1/2" Ports) ( ) 3.25 (83) Panel mount kit with T-bar adjustment Bonnet included (16) 1.88 (8) 2.25 (57) 0.28 (7) 0. (11) 2. (62) 1.25 (32) Panel mount kit with hand wheel adjustment Bonnet included Bracket (Units with 3/" and 1" Ports) ( ).88 (12) Panel mount kit with screw adjustment Bonnet included Units with 1/2" ports: Units with 3/" and 1" ports: (8) 2.9 (75) 3.27 (83) 5.38 (137) 3.31 (8) APP-18

15 Regulator Accessories Screw adjustment Tamper resistant cap Bracket ( ) 2.9 (75) 0.63 (16) 0.31 (8).88 (12) 3.25 (83) 0.50 (13) 3.19 (81) 3.19 (81) Muffler 3/ PTF: MB006A R3/: MB006B 11-0 Bracket ( ) 2.7 (63) 0.63 (16) 1.63 (1) 11-0 with plastic nut Bracket and plastic nut: Plastic nut: Metal nut: (7) 0.93 (2) 0.22 (6) Tamper resistant knob (10) AL Bracket 20AL Bracket ( ) 3.25 (83) 2.25 (57) 2. (62) 0.63 (16) 1.88 (8) 0. (11) 0.28 (7) 1.25 (32) APP-19

16 Filter/Regulator Accessories B05 Plastic Panel Nut B07 with plastic nut Tamper resistant knob Bracket and plastic nut: Plastic nut: Metal nut: B07, B39 Bracket ( ) 2.7 (63) 0.29 (7) 0.38 (10) 0.93 (2) 0.63 (16) 0.22 (6) 1.63 (1) B38 Bracket ( ) B38 Aluminum wall bracket and nut: Aluminum nut: (75) Plastic adjusting knob Stainless steel wall bracket and nut: Stainless steel nut: (75) 2.13 (5) B39 with plastic nut Bracket and plastic nut: Plastic nut: Metal nut: (28) 0.3 (8.5) Tamper resistant knob APP-150

17 Filter/Regulator Accessories B6 Tamper resistant cover and wire. Install over knob to help prevent tampering of pressure setting. Use up to padlocks with 5/16" (8mm) diameter shackle to secure cover. Lockout hasp may also be used. Allows use of up to 6 padlocks with 5/16" (8mm) diameter shackle Cover and wire: Wire: B6 Bracket (750-50) 0.32 (8.2) 3.35 (85) 5.63 (13).9 (11) 1.20 (30.5) 1.89 (8) 3.66 (93).33 (110) 0.3 (11) 0.57 (1.5) B68 1/2", 3/", 1", 1-1/" Ports: /2" Ports: Not Available B68 Bracket ( ) Tamper resistant cover and wire. Install over knob to help prevent tampering of pressure setting. Use up to padlocks with 5/16" (8mm) diameter shackle to secure cover. Lockout hasp may also be used. Cover and wire: Wire: (72) (190) 0.59 (15) Allows use of up to 6 padlocks with 5/16" (8mm) diameter shackle. 3.9 (100) 1.97 (50) 7.8 (190)* 8.19 (208)* 0.33 (8.5) * Add 0.39" (10) for 1-1/" ported yokes. APP-151

18 Filter/Regulator Accessories B72 B73 /plastic nut Tamper resistant cover and wire. Install over knob to help prevent tampering of pressure setting. Use up to 2 padlocks with 5/16" (8mm) diameter shackle to secure cover. Lockout hasp may also be used. Allows use of up to 6 padlocks with 5/16" (8mm) diameter shackle Bracket and plastic nut: Plastic nut: Metal Nut: Cover and wire: Wire: B72 Bracket (22-50) 0.20 (5) 0.16 () (5) 0.79 (20) 0.7 (12) B73 Bracket (2-50) 2.37 (60) 1.5 (39) 2.6 (67) 2.36 (60) B72 Neck Bracket ( ) 1.0 (25).60 (15) 1.9 (9) 1.2 (30) 2.5 (6) 0.3 (8) 0.2 () B73 Neck Bracket (61-50) 1.5 (38) 2.36 (60) 0.3 (8) 2.75 (70) /metal nut Bracket and metal nut: Metal Nut: Plastic Nut: () 1.10 (28) (38) 0.66 (17) Tamper resistant cover and wire. Install over knob to help prevent tampering of pressure setting. Use up to padlocks with 5/16" (8mm) diameter shackle to secure cover. Lockout hasp may also be used. Cover and wire: Wire: (7) 0.7 (19) 1.89 (8) 2.0 (61) 1.5 (38) 1.0 (25) 0.27 (7) Allows use of up to 6 padlocks with 5/16" (8mm) diameter shackle. B7 Bracket (32-50) B7 Neck Bracket (368-51) 2.88 (73) 3.5 (89) B (83) 2.06 (52) 3.37 (86) /metal nut Tamper resistant cover and wire. Install over knob to help prevent tampering of pressure setting. Use up to padlocks with 5/16" (8mm) diameter shackle to secure cover. Lockout hasp may also be used. Allows use of up to 6 padlocks with 5/16" (8mm) diameter shackle. Bracket and metal nut: Metal Nut: Cover and wire: Wire: (5) 0.16 () 0.77 (20) 1.6 (37) 1.00 (25) 1.97 (50) 2.0 (61) 1.38 (35) 0.9 (23) 2.2 (56) 0.95 (2) 0.28 (7) APP-152

19 Lubricator Accessories L07 L17 with plastic nut - use with 1 and 2 quart reservoirs only Bracket and plastic nut: Plastic nut: Metal nut: /", 1" Ports: /", 1-1/2" Ports: L07 Bracket ( ) 2.7 (63) 0.29 (7) 0.38 (10) 0.93 (2) 0.63 (16) 0.22 (6) 1.63 (1) Pyrex dome and metal fill plug L17 Bracket ( , ) L17 Strap ( /056) Quick fill cap. Use with oil pump, pail, and hose assembly (see catalog sheet NC-26) to refill reservoir without shutting off air supply. Replaces fill plug (130) 3.19 (81) 1.00 (25) A Fill plug with 1/8 PTF tapped hole. Use with customer supplied pressurized oil source to refill reservoir without shutting off air supply. Replaces standard fill plug (76) 1.69 (3) 0.56 (1) Dia. L (9) Dia. Bracket A B (76) (225) (127) (330) L22 Bracket ( ) 3.5 (90) 1.22 (31).80 (122).06 (103) 0.33 (8.5) 2.05 (52) APP-153

20 Lubricator Accessories L6 Tamper resistant seal wire for sightfeed dome Low oil level switch. Provides electrical signal for warning or shutdown when oil level is low. Quick fill cap Use with oil pump, pail, and hose assembly (see catalog sheet NC-26) to refill reservoir without shutting off air supply. Replaces fill plug. 7 ounce bowl: quart bowl: qt reservoir: L6 Bracket (750-52) 0.32 (8.2) 5.09 (129) 5.63 (13).9 (11) 3.62 (92) 12 (30.5) 36.6 (93) 5.3 (13) Remote fill - use with 7 ounce reservoir only Use with customer supplied pressurized oil source to automatically refill reservoir (11) 0.57 (1.5) L68 1/2", 3/", 1", 1-1/" Ports: /2" Ports: Not Available L68 Bracket ( ) 2.8 (72) Tamper resistant seal wire for sightfeed dome (190) 0.59 (15) Quick fill cap. Use with oil pump, pail, and hose assembly (see catalog sheet NC-26) to refill reservoir without shutting off air supply. Replaces fill plug (100) 1.97 (50) 7.8 (190)* 8.19 (208)* 0.33 (8.5) Remote fill - use with 1 qt reservoirs only Use with customer supplied pressurized oil source to automatically refill reservoir APP-15

21 Lubricator Accessories L L73 Quick fill cap. Use with oil pump, pail, and hose assembly (see catalog sheet NC-26) to refill reservoir without shutting off air supply. Replaces fill plug L6 Bracket (750-50) 0.32 (8.2) 3.35 (85) 5.63 (13).9 (11) 1.20 (30.5) 1.89 (8) 3.66 (93).33 (110) 0.3 (11) 0.57 (1.5) L7 7 ounce bowl: quart bowl: L73 Bracket (2-50) 2.37 (60) 2.6 (67) Low oil level switch - use with 1 qt reservoir only Provides electrical signal for warning or shut down when oil level is low () 1.10 (28) 0.71 Quick fill cap. Use with oil pump, pail, and hose assembly (see catalog sheet NC-26) to refill reservoir without shutting off air supply. Replaces fill plug L7 Bracket (32-50) 2.88 (73) 3.25 (83) 0.20 (5) 0.16 () 1.6 (37) 1.00 (25) 0.77 (20) 0.28 (7) 0.7 (19) 1.89 (8) 2.0 (61) Remote fill - use with 7 ounce reservoir only Use with customer supplied pressurized oil source to automatically refill reservoir (50) 2.0 (61) APP-155

22 Relief Valve Accessories V06 for V06 with plastic bonnet for V06 with brass bonnet Tamper resistant knob kit Bracket and plastic nut: Plastic nut: Metal nut: Bracket and metal nut: Metal nut: V06, V07 Bracket ( ) 2.7 (63) 0.29 (7) 0.38 (10) 0.93 (2) 0.63 (16) 0.22 (6) 1.63 (1) V06 Bracket for Brass Bonnet ( ) 2.1 (61) 0.35 (9) 1.0 (25) 1.38 (35) 0.63 (16) 0.22 (6) 1.63 (1) V07 with plastic nut Bracket and plastic nut: Plastic nut: Metal nut: V6 Bracket (750-50) 0.38 (10) Tamper resistant knob kit (8.2) 3.35 (85) 5.63 (13).9 (11) 1.20 (30.5) 1.89 (8) V (93).33 (110) Muffler 1/2 PTF: MB00A R1/2: MB00B 0.3 (11) 0.57 (1.5) V68 Bracket ( ) V68 3/", 1", 1-1/" Ports: /2" Ports: Not Available 2.8 (72) Muffler 1/2 PTF: MB008A R1/2: MB008B 7.8 (190) 0.59 (15) 3.9 (100) 1.97 (50) 0.33 (8.5) 7.8 (190)* 8.19 (208)* * Add 0.39" (10) for 1-1/" ported yokes. APP-156

23 Relief Valve Accessories V72 /plastic nut Tamper resistant cover and wire. Install over knob to help prevent tampering of pressure setting. Use up to 2 padlocks with 5/16" (8mm) diameter shackle to secure cover. Lockout hasp may also be used Bracket and plastic nut: Bracket and metal nut: Plastic nut: Metal Nut: Cover and wire: Wire: V72 Bracket (22-50) 0.20 (5) 0.16 () (5) 0.79 (20) 0.7 (12) 1.5 (39) 2.36 (60) V72 Neck Bracket ( ) 1.0 (25).60 (15) 1.9 (9) 1.2 (30) 0.3 (8) 0.2 () 2.36 (60) 0.3 (8) V7 Bracket (32-50) V7 Neck Bracket (368-51) 2.88 (73) V (83) 2.06 (52) 3.37 (86) /metal nut Bracket and metal nut: Metal Nut: (5) 0.16 () 1.6 (37) 1.00 (25) 1.97 (50) 0.77 (20) 2.0 (61) 1.38 (35) 0.9 (23) 2.2 (56) 0.95 (2) 0.28 (7) Tamper resistant cover and wire. Install over knob to help prevent tampering of pressure setting. Use up to padlocks with 5/16" (8mm) diameter shackle to secure cover. Lockout hasp may also be used. Cover and wire: Wire: APP-157

24 Accessories T72 Mufflers (T72T) (use only with T72E and T72T) Diffuser (10-32 and M5): Muffler (10-32): MS000A Muffler (M5): T0M0500 T72 Bracket (22-50) 0.20 (5) 0.16 () (5) 0.79 (20) 0.7 (12) 1.5 (39) 2.36 (60) T6 Muffler (T6T) Muffler (1/8 PTF): MS001A Muffler (R1/8): T0B1800 T68 T73 Mufflers (T73T) Diffuser (10-32 and M5): Muffler (10-32): MS000A Muffler (M5): T0M0500 T7 Muffler (T7T) Muffler (1/8 PTF): MS001A Muffler (R1/8): T0B1800 APP-158

25 Accessories P72 P6F Mufflers for P72C and P72F Lockout hasp for P72F. Muffler 1/ PTF: MB002A R1/: MB002B /2 PTF: MB00A R1/2: MB00B P6 Bracket (750-50) 0.32 (8.2) 3.35 (85) 5.63 (13).9 (11) 1.20 (30.5) 1.89 (8) 3.66 (93).33 (110) 0.3 (11) 0.57 (1.5) P68F 3/", 1", 1-1/" Ports: /2" Ports: Not Available P68 Bracket ( ) 2.8 (72) (190) 0.59 (15) Muffler 1" PTF: MB008A R1 : MB008B 3.9 (100) 1.97 (50) 0.33 (8.5) 7.8 (190)* 8.19 (208)* P P7 Bracket (32-50) 2.88 (73) 3.25 (83) 0.20 (5) 0.16 () 1.6 (37) 1.00 (25) 0.77 (20) Mufflers for P7C and P7F 1/2 PTF: MB00A R1/2: MB00B Lockout hasp for P7F and P7C with lockout slide: 1.97 (50) 2.0 (61) APP-159