BigDog Mowers Stout MP Parts Manual

Transcription

1 BigDog Mowers Stout MP Parts Manual 00 South Ridge Road Hesston, Kansas 6706

2 WARNING The engine exhaust from this product contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. NOTICE OF REQUIREMENT OF SPARK ARRESTER MUFFLER This equipment may create sparks that can start fires around dry vegetation. California Public Resources Code Section.6 provides that it is unlawful to use or operate an internal combustion engine on any forest-covered, brush-covered, or grass-covered land unless the engine is equipped with a spark arrester maintained in effective working order. A spark arrester is a device constructed of nonflammable materials specifically for the purpose of removing and retaining carbon and other flammable particles over 0.0 of an inch in size from the exhaust flow of an internal combustion engine that uses hydrocarbon fuels or which is qualified and rated by the United States Forest Service. Other states or federal areas may have similar laws. The Operator Should Contact Local Fire Agencies For Laws or Regulations Relating to Fire Prevention Requirements. THIS EQUIPMENT DOES NOT HAVE A SPARK ARRESTER AND YOU SHOULD CONTACT YOUR AUTHORIZED DEALER FOR THE PURCHASE OF A SPARK ARRESTER. Inspect spark arrester daily; replace every 00 hours or as needed. The Engine Owner s Manual provides information regarding the U.S. Environmental Protection Agency (EPA) and the California Emission Control Regulation of emission systems, maintenance and warranty. Keep Engine Owner s Manual with your unit. Should the Engine Owner s Manual become damaged or illegible, replace immediately. Replacements may be ordered per the information found in the Product Information section of the owner s manual. Federal law and California State law prohibit the following acts or the causing thereof:. The removal or rendering inoperative by any person other than for purposes of maintenance, repair, replacement, of any device or element of design incorporated into any equipment for the purposes of emissions control prior to or after its sales or delivery to the ultimate purchaser or while it is in use, or. The use of the equipment after such device or element of design has been removed or rendered inoperative by any person.

3 Table of Contents General Information Service Literature Options Available From Your Dealer Using This Manual Hardware Description Codes & Abbreviations Standard Torques Section Frame Lights Engine Guard Section Hydraulic Transmissions Transmission Assembly Transmission Service Parts Steering Steering Sub-Assembly Brake Section Wheel & Tire Front Tire Breakdown Drive Wheel Breakdown Section Engine Engine Service Parts Fuel System Fuel System Service Parts Section 6 Battery Instrument Panel Section 7 " Service Deck " Deck Pulleys & Spindles " Deck " Service Deck " Deck Pulleys & Spindles " Deck Deck Lift Deck Mounting Hardware Section 8 Seat Seat Service Parts ROPS Foldable _07 c-

4 c- 990_07

5 General Information This manual covers Big Dog Stout MP models 976 & 98. Service Literature PART NO. DESCRIPTION 609 OPERATOR S MANUAL 06 WARRANTY STATEMENT 0 GENERAL SERVICE MANUAL Options Available From Your Dealer PART NO. DESCRIPTION 6 MULCH KIT " DECK 9 MULCH KIT 60" DECK BAG CATCHER " DECK 908 -BAG CATCHER 60" DECK 7 STEERING EXTENSION KIT 60 FLEX FORKS 6 CONTAINMENT KIT " DECK 66 CONTAINMENT KIT 60" DECK 087 SEAT SPRING KIT Note: When ordering parts, you must use the part number as shown for each part, not the index number. Always give the model and serial number to your parts and service representative. Note: Items sold in bulk such as seals and hoses are sold by the foot. Using This Manual This manual is part of a service package for the BigDog mowers. Use of this manual in conjunction with other Big- Dog mower and component manuals will provide the information necessary to service and maintain BigDog mowers. This Parts Manual provides a complete parts listing for the unit. Use this manual when ordering parts. Illustrations used were current at the time of printing, but subsequent production changes may cause your machine to vary slightly in detail. Excel Industries, Inc. reserves the right to redesign and change the machine as deemed necessary, without notification. If a change has been made to your machine which is not reflected in this parts manual, see your authorized dealer for current information and parts. The Service Manual is a service guide for use by Service Technicians. It provides the necessary information needed to perform normal maintenance requirements on these units. The Operator's Manual provides fundamental operational information and operational safety that is needed when operating the mower. The component manuals are furnished by the various manufacturers to be used for the troubleshooting and servicing of their products. 990_07 -

6 Hardware Description Codes & Abbreviations The following codes are used throughout this parts manual. Refer to this list when ordering parts. ABBREVIATION DESCRIPTION ABBREVIATION DESCRIPTION CB CARRIAGE BOLT MB MACHINE BUSHING CE CLEVIS PIN MS MACHINE SCREW CN CLIP NUT NT NUT CP COTTER PIN SC SELF TAPPING CAP SCREW CS CAP SCREW SH SOCKET HEAD CW CUP WASHER SB SHOULDER BOLT FDRW FENDER WASHER SS SET SCREW FW FLAT WASHER OD OUTSIDE DIAMETER HX HEX HEAD ID INSIDE DIAMETER LW LOCK WASHER Standard Torques The following chart lists the standard torque values for the threaded fasteners found in this manual. Torque all cap screws, nuts and set screws to these values unless a different torque is shown in the Notes section next to the fastener. SIZE FT-LBS N M SIZE FT-LBS N M M.. 7 M M M M M M M M M0 0 M _07

7 Section Frame Lights Engine Guard _07 -

8 Frame _07

9 Frame INDEX NO. PART NO. QTY. DESCRIPTION 67 " FRAME (WITH DECALS & RIVET NUTS) " FRAME (WITH DECALS & RIVET NUTS) /8-6 THREAD RIVET NUT 8088 /6-8 THREAD RIVET NUT 609 BIGDOG STOUT MP LOGO DECAL BUMPER BIG DOG DECAL /8-6 THREAD HEX RIVET NUT CN.-8 X.0 MAX THK DECK HEIGHT DECAL RS STEERING DECAL PUMP BELT WARNING DECAL 7988 FUEL INDICATOR DECAL TOW VALVE DECAL 600 HOT DECAL ENGINE COMPARTMENT DECAL 6 N/A SERIAL NUMBER / SPEC DECAL LS STEERING DECAL MADE IN USA DECAL SAFE OPERATION DECAL 0 09 GREASE FITTING STRAIGHT NOTES:. In the event the serial number decal becomes damaged or illegible, please contact your dealer to order a replacement.. EPA compliance plate.. Patent numbers plate. 990_07 -

10 Lights BOTTOM BB BOTTOM OF THE MOWER - 990_07

11 Lights INDEX NO. PART NO. QTY. DESCRIPTION 6000 LIGHT 60 CS #8- X.00 PH TRX THREAD FORMING 607 WIRE HARNESS 6007 PUSH BUTTON MOUNT WIRE TIE NOTES: 990_07 -

12 Engine Guard _07

13 Engine Guard INDEX NO. PART NO. QTY. DESCRIPTION 67 BUMPER (WITH DECAL) 988 ENGINE GUARD SCREEN NT.-8 HX FLK ZNYC 06 8 CB.-8 X.7 FUL ZN 6007 BIG DOG DECAL PLASTIC WHEEL ASSEMBLY 7 67 FW.0 X. X.87 SPL NT.00- HX G8 ZY NL CS.7-6 X. HX G FW.79 X.8 X CS.00- X. HX G FW. X.06 X PLASTIC WHEEL 099 NT.00- HX JAM ZNYC NOTES: 990_07-7

14 -8 990_07

15 Section Hydraulic Transmissions Transmission Assembly Transmission Service Parts Steering Steering Sub-Assembly Brake _07 -

16 Hydraulic Transmissions _07

17 Hydraulic Transmissions INDEX NO. PART NO. QTY. DESCRIPTION 0888 CS.-8 X. HX G FW. X.687 X.0/.080H CS.-8 X.0 HX G 000 WIRE TIE 0007 CS.6- X.7 HX G IDLER PULLEY.00" OD SPRING / COIL PL FW.78 X. X.0 ZN BUSHING 0 77 PUMP TENSIONER 096 FW.760 X.6 X.08 ZNYC 6008 SB.70 X.00 SH.6-60 BELT, A SEC, 67.6 EL N/A TRANSMISSION ASSEMBLY 07 8 NT.-8 HX G OVERFLOW TANK (WITH CAP) OVERFLOW TANK CAP FW.8 X.6 X NT.0-0 HX ZY NL CS.0-0 X.7 HX G TOW LINK ROD 08 CP.06D X.00 LG HML Z. Torque to 00 ft-lbs.. Torque to 7 ft-lbs. NOTES: 990_07 -

18 Transmission Assembly _07

19 Transmission Assembly INDEX NO. PART NO. QTY. DESCRIPTION 607 LS TRANSMISSION 6070 RS TRANSMISSION HYDRAULIC FITTING, DEG 6000 SPRING CLAMP 6008 OVERFLOW HOSE 6 07 NT.-8 HX G FW. X.687 X.0/.080H SPRING CLAMP OVERFLOW HOSE FITTING, 90-9/6 SAE 789 BALL STUD 600 STEERING DAMPER 060 CS.7-6 X.00 HX G 799 FW.06 X.00 X. HRD Z SPACER TUBE CAPLOCK. Torque to 0 ft-lbs. NOTES: 990_07 -

20 Transmission Service Parts INDEX NO. PART NO. QTY DESCRIPTION 609 FAN/PULLEY KIT RETAINING CLIP 60 BRAKE ARM OIL FILTER 6087 PUMP ARM & HARDWARE SPACER BOLT HUB KIT LS FILTER GUARD RS FILTER GUARD (NOT SHOWN) CHARGE COVER KIT (WITH O-RING) 0 60 O-RING NOTES: _07

21 This page intentionally left blank. 990_07-7

22 Steering STEERING SUB-ASSEMBLY _07

23 Steering INDEX NO. PART NO. QTY DESCRIPTION 789 LOCK COLLAR 0.77 ID 06 NT.- HX NL G 768 FW. X.687 X.0/.080H PUMP ROD 006 CS.7-6 X.7 HX G NT.7-6 HX JAM G Z CS.0-0 X.7 HX G FW.8 X.6 X STEER TUBE SUPPORT CS.-8 X.00 HX G 69 PLATED PIVOT TUBE LW. INT-EXT TOOTH 07 NT.-8 HX G 789 BALL STUD 097 NT.0-0 HX G ZNYC SPACER 7 0 NT.- HX ZNYC. Part of the Transmission Assembly. NOTES: 990_07-9

24 Steering Sub-Assembly INDEX NO. PART NO. QTY. DESCRIPTION 7860 STEERING BAR GRIP 6087 STEERING BAR (WITH GRIP) 7679 FW.79 X.8 X CS.7-6 X.7 HX G NT.7-6 HX G ZY NL LEFT STEERING ARM 078 RIGHT STEERING ARM (NOT SHOWN) BUSHING LS STEER PIVOT 0787 RS STEER PIVOT (NOT SHOWN) NOTES: _07

25 This page intentionally left blank. 990_07 -

26 Brake STEERING ARM MOWER FRAME HYDRAULIC TRANSMISSION - 990_07

27 Brake INDEX NO. PART NO. QTY. DESCRIPTION NT.7-6 HX G ZY NL 7679 FW.79 X.8 X SWITCH 0008 CS.7-6 X.0 HX G Z 600 BRAKE ROD ASSEMBLY 6 00 NT.7-6 HX G ZNY 7 06 NT.- HX NL G FW. X.687 X.0/.080H BUSHING LS BRAKE BELL CRANK 0789 RS BRAKE BELL CRANK 0806 CS.7-6 X.0 HX G SHORT BRAKE LINK ROD 60 SPRING 090 LS BRAKE SPRING LINK 090 RS BRAKE SPRING LINK (NOT SHOWN) CS.0-0 X.7 HX G NT.0-0 HX FL LK ZNY OVERTRAVEL SPRING NOTES: 990_07 -

28 - 990_07

29 Section Wheel & Tire Front Tire Breakdown Drive Wheel Breakdown _07 -

30 Wheel & Tire _07

31 Wheel & Tire INDEX NO. PART NO. QTY. DESCRIPTION 6079 TIRE/WHEEL ASSEMBLY X WHEEL BACKUP PLATE WHEEL NUT 709 CS.00- X. HX G 67 FW.0 X. X.87 SPL FW. X.7 X. ZNY 7 78 BEARING SPACER 9 N/A FRONT TIRE ASSEMBLY. Torque to 6 7 ft-lbs. NOTES: 990_07 -

32 Front Tire Breakdown _07

33 Front Tire Breakdown INDEX NO. PART NO. QTY. DESCRIPTION 90 FORK 07 CS.70-0 X 9.0 HX ZY 096 FW.760 X.6 X.08 ZNYC 060 NT.70-0 HX ZY NL 6099 TIRE/WHEEL X TIRE X WHEEL BEARING BEARING SPACER WHEEL 6 X TIRE VALVE NOTES: 990_07 -

34 Drive Wheel Breakdown INDEX NO. PART NO. QTY. DESCRIPTION 6078 TIRE X WHEEL 0 X VALVE STEM NOTES: _07

35 Section Engine Engine Service Parts Fuel System Fuel System Service Parts _07 -

36 Engine _07

37 Engine INDEX NO. PART NO. QTY. DESCRIPTION N/A KAWASAKI FX69V & FX70V ENGINE 600 MUFFLER 066 CS.-8 X.000 HX G FW. X.687 X.0/.080H 96 CLUTCH ANCHOR NT.-8 HX G OIL DRAIN VALVE 8 06 CB.-8 X.70 FUL ZN MUFFLER SHIELD CS.7-6 X. HX G8 P8 77 KEY / SQ X.66 LG 60 PULLEY 7679 FW.79 X.8 X K CLUTCH KIT 000 WIRE TIE 6 79 CLUTCH HARNESS PIGTAIL FW. X. X.9 HRD CS.7-0 X.0 HX G P8 NOTES:. Supplied with the engine.. Torque to 8 ft-lbs. Replace (do not reuse) the cap screw if it s removed or loosened. Use only hand tools to install this fastener.. Torque to 0 ft-lbs.replace (do not reuse) the cap screw if it s removed or loosened. Use only hand tools to install this fastener.. Torque to ft-lbs. 990_07 -

38 Engine A FUSE 6 0 A VAPOR TEE SEAT SUPPORT B - 990_07

39 Engine INDEX NO. PART NO. QTY. DESCRIPTION NEGATIVE BATTERY CABLE POSITIVE BATTERY CABLE 088 8" /" FUEL LINE 60 CLAMP, /6" 000 HOSE CLAMP 606 " /6" VAPOR LINE 89 GROUND STRAP LW.7 INT-EXT TOOTH NOTES: FUEL & VAPOR LINE LENGTHS A B 8" FILTER TO FUEL VALVE (FUEL) " ENGINE PORT TO TEE (VAPOR). Part of the wire harness. 6. Part of the Fuel System. 990_07 -

40 Engine Service Parts INDEX NO. PART NO. QTY. DESCRIPTION 786 MAIN AIR FILTER 7879 SAFETY AIR FILTER 608 OIL FILTER IN-LINE FUEL FILTER 768 VACUATOR VALVE NOTES: _07

41 This page intentionally left blank. 990_07-7

42 Fuel System A C 6 B D 6 E _07

43 Fuel System INDEX NO. PART NO. QTY. DESCRIPTION RS FUEL TANK 6000 LS FUEL TANK 6096 RATCHETING GAS CAP." 000 HOSE CLAMP 066 CS.-8 X.00 HX G FW. X.687 X.0/.080H FW.06 X.00 X. HRD Z CS.7-6 X.7 HX G LOOP CLAMP NT.-8 HX FLK ZNYC 709 FUEL VALVE -WAY 608 PLASTIC TEE, /6" 000 WIRE TIE 600 VACUUM BREAKER 088 6" /" FUEL LINE " /6" VAPOR LINE NOTES: FUEL LINE LENGTHS A B C D E " RIGHT TANK TO VALVE (FUEL) " LEFT TANK TO VALVE (FUEL) " RIGHT TANK TO TEE (VAPOR) " TEE TO VACUUM BREAKER (VAPOR) 6" LEFT TANK TO VACUUM BREAKER (VAPOR). Torque to 7 ft-lbs. 990_07-9

44 Fuel System Service Parts INDEX NO. PART NO. QTY. DESCRIPTION 6087 VENT FITTING 6000 GROMMET 789 SUCTION HOSE GROMMET 607 SUCTION HOSE ASSY 9." 6066 VACUUM BREAKER FILTER NOTES: _07

45 Section 6 Battery Instrument Panel _07 6-

46 Battery POSITIVE BATTERY CABLE NEGATIVE BATTERY CABLE _07

47 Battery INDEX NO. PART NO. QTY. DESCRIPTION 768 CS.-8 X.00 HX G 768 FW. X.687 X.0/.080H 87 BATTERY CLAMP STRAP 099 CS.0-0 X.7 HX G LW.0 INT-EXT TOOTH Z NT.0-0 HX G ZNYC RED BATTERY CABLE BOOT GM.0 X. X WIRE TIE (NOT SHOWN) NOTES: 990_07 6-

48 Instrument Panel 0 9 0A FUSE A FUSE _07

49 Instrument Panel INDEX NO. PART NO. QTY. DESCRIPTION CHOKE CABLE PTO SWITCH 77 RED INDICATOR LIGHT KEY ASSEMBLY CB 0- X.00 ZYNC NT #0- HX NL ZN IGNITION SWITCH FW.9 X.00 X.08 ZNYC THROTTLE CABLE CS.0-0 X.00 HX G 768 FW.8 X.6 X INSTRUMENT PANEL DECAL 06 INSTRUMENT PANEL (WITH DECAL) WIRE TIE HOUR METER WIRE HARNESS SEALED RELAY (WITH BRACKET) 8 0 CLUTCH CONNECTOR REPAIR KIT FUSE HOLDER. Part of the wire harness. NOTES: 990_07 6-

50 _07

51 Section 7 " Service Deck " Deck Pulleys & Spindles " Deck " Service Deck " Deck Pulleys & Spindles " Deck Deck Lift Deck Mounting Hardware _07 7-

52 " Service Deck _07

53 " Service Deck INDEX NO. PART NO. QTY DESCRIPTION 0 " DECK (WITH DECALS & HARDWARE) 789 BELT ROUTING DECAL CN.-8 X.0 MAX THK 60 DANGER/OBJECTS DECAL 7997 " DECK ID DECAL 6 60 DANGER/CHUTE DECAL NOTES: 990_07 7-

54 " Deck Pulleys & Spindles _07

55 " Deck Pulleys & Spindles INDEX NO. PART NO. QTY. DESCRIPTION 796 CS.6- X.0 HX G 088 FW.6 X.00 X DUST SHIELD WITH OFFSET 7886 IDLER PULLEY, NHI.0" IDLER SLIDE TENSION SPRING 7 98 CHAIN CS.-8 X. FLT SH IDLER SLIDE CS.6- X. HX G Z 07 FW.688 X.7 X.60HD DRIVE PULLEY.68 OP 00 NT.7-6 HX G ZNY 7679 FW.79 X.8 X CS.7-6 X.7 HX G BLADE SPINDLE FW. X.687 X.0/.080H NT.-8 HX G ZY NL NT.00- HX G8 ZY NL PLASTIC WHEEL ASSEMBLY (WITH HARDWARE) FW. X.06 X CS.-8 X.7 HX G 09 HEAVY DUTY PULLER 07 NT.-8 HX G CS.00- X. HX G PLASTIC WHEEL NT.00- HX JAM ZNYC. Torque to 8 ft-lbs. NOTES: 990_07 7-

56 " Deck DISCHARGE CHUTE FRONT WALL _07

57 " Deck INDEX NO. PART NO. QTY. DESCRIPTION BELT, B " EL 6079 LS PULLEY COVER 6078 RS PULLEY COVER 080 CS.-8 X.7 HX G 797 FW. X.00 X. HRD Z DISCHARGE CHUTE TORSION SPRING CHUTE PIN CHUTE BRACKET CHUTE ADAPTER PLATE 09 CB.7-6 X.00 G ZNY NT.7-6 HX G ZY NL 7679 FW.79 X.8 X BLADE, 8.0"-L-F-CW BLADE, F8.0"-H-F-CW BLADE, 8.0"-MUL-F-CW 7977 BLADE, 8.0"-GAT-F-CW 787 CW.6. X.87 PNT CS.6- X. HX G Z NT.-8 HX G ZY NL "A" BLOWOUT BAFFLE 9 06 CB.-8 X.7 FUL ZN FW. X.687 X.0/.080H NOTES:. Torque to 8 ft-lbs.. Do not torque; the discharge chute must pivot freely. 990_07 7-7

58 60" Service Deck _07

59 60" Service Deck INDEX NO. PART NO. QTY. DESCRIPTION " DECK (WITH DECALS & HARDWARE) 789 BELT ROUTING DECAL CN.-8 X.0 MAX THK 60 DANGER/OBJECTS DECAL 60 DANGER/CHUTE DECAL " DECK DECAL NOTES: 990_07 7-9

60 60" Deck Pulleys & Spindles _07

61 60" Deck Pulleys & Spindles INDEX NO. PART NO. QTY. DESCRIPTION 796 CS.6- X.0 HX G 088 FW.6 X.00 X DUST SHIELD WITH OFFSET 7886 IDLER PULLEY, NHI.0" IDLER SLIDE TENSION SPRING 7 79 CHAIN, LINK CS.-8 X. FLT SH IDLER SLIDE UHMW CS.6- X. HX G Z 07 FW X.70 X 0.60HD 607 DECK DRIVE PULLEY 00 NT.7-6 HX G ZNY 7679 FW.79 X.8 X BLADE SPINDLE CS.7-6 X.7 HX G PLASTIC WHEEL ASSEMBLY (WITH HARDWARE) FW. X.06 X NT.00- HX G8 ZY NL FW. X.687 X.0/.080H NT.-8 HX G ZY NL 09 HEAVY DUTY PULLER 07 NT.-8 HX G 080 CS.-8 X.7 HX G CS.00- X. HX G PLASTIC WHEEL NT.00- HX JAM ZNYC. Torque to 8 ft-lbs. NOTES: 990_07 7-

62 60" Deck DISCHARGE CHUTE FRONT WALL 7-990_07

63 60" Deck INDEX NO. PART NO. QTY. DESCRIPTION DISCHARGE CHUTE 608 TORSION SPRING 608 CHUTE PIN NT.7-6 HX G ZY NL 7679 FW.79 X.8 X CHUTE BRACKET CHUTE ADAPTOR PLATE 8 09 CB.7-6 X.00 G ZNY CS.-8 X.7 HX G FW. X.687 X.0/.080H 88 RS PULLEY COVER 88 LS PULLEY COVER 607 BELT, B BLADE, 0.0"-L-F-CW 79 BLADE, 0.0"-MUL-F-CW 790 BLADE, 0.0"-GAT-F-CW 7968 BLADE, F0.0"-H-F-CW 787 CW.6 X. X.87 PNT CS.6- X. HX G Z 7 06 CB.-8 X.7 FUL ZN NT.-8 HX G ZY NL 9 8 BLOWOUT BAFFLE NOTES:. Torque to 8 ft-lbs.. Do not torque; the discharge chute must pivot freely. 990_07 7-

64 Deck Lift _07

65 Deck Lift INDEX NO. PART NO. QTY DESCRIPTION 88 STOP HANDLE 88 HEIGHT ADJ STOP 7888 DECK LIFT INDICATOR 609 DECK LIFT ROD CS.7- X.7 HX G 6 60 DECK LIFT CHAIN NT.7- HX FLG ZN FW.78 X.0 X.0 ZNYC E CLIP.00 X.6 X CS.-8 X.0 HX G 07 NT.-8 HX G 88 DECK LEVELER YOKE FW. X.06 X CE.70 X. X.7 HEAD 7899 DECK LIFT SPRING CS.7- X.7 HX G NOTES: 990_07 7-

66 Deck Mounting Hardware _07

67 Deck Mounting Hardware INDEX NO. PART NO. QTY DESCRIPTION CS.00- X.00 HX G ZNY NT.00- HX G ZNYC NOTES: 990_07 7-7

68 _07

69 Section 8 Seat Seat Service Parts ROPS Foldable _07 8-

70 Seat _07

71 Seat INDEX NO. PART NO. QTY. DESCRIPTION 607 SEAT 080 CS.-8 X.7 HX G FW. X.687 X.0/.080H 6088 SEAT LATCH ASSEMBLY 0988 SEAT PAN (WITH DECAL) NT.-8 HX G ZY NL 7 07 NT.-8 HX G CS.7-6 X. HX G FW.79 X.8 X SEAT SPRING 0 LB/IN 090 SEAT PAN STOP 060 CS.-8 X.87 HX G ZN 000 WIRE TIE 9099 FLOOR PAN 608 BATTERY WARNINGS DECAL NT.7-6 HX G ZY NL NOTES:. Do not torque; the seat pan and the seat pan stop must pivot freely. 990_07 8-

72 Seat Service Parts 6 INDEX NO. PART NO. QTY. DESCRIPTION 6007 ARMRESTS (PAIR) 6006 SEAT BACK 600 SEAT BOTTOM 609 SEAT BELT 609 STANDARD SLIDES (PAIR) SEAT SWITCH NOTES: 8-990_07

73 This page intentionally left blank. 990_07 8-

74 ROPS Foldable _07

75 ROPS Foldable INDEX NO. PART NO. QTY. DESCRIPTION 609 ROPS KIT (WITH DECALS, SEAT BELT & HARDWARE) CS.00- X.0 HX G 607 ROPS STOP 07 6 NT.00- UNT LK G8 ZN 6070 HAND KNOB LYNCH PIN W/ LANYARD FW. X.06 X ROPS DECAL. Torque to ft-lbs. NOTES: 990_07 8-7

76 _07