Halfshaft SPECIAL SERVICE TOOL(S) REQUIRED
|
|
- Nathan Clark
- 5 years ago
- Views:
Transcription
1 Page 1 of 8 Section 05-04: Halfshaft, Front Wheel 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Halfshaft SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Remover Adapter 211-S211 (T96P-3010-A1) Tie-Rod Remover Adapter (T81P-3504-W) Steering Arm Remover (T64P-3590-F) Front Hub Tool (T81P-1104-C) Hub Adapter (T86P-1104-A1) Metric Hub Remover Set (T83P-1104-BH) Installing Adapter (T81P-1104-A) Removal 1. CAUTION: Do not begin this procedure unless the following parts are available: A new front axle wheel hub retainer. A new front suspension lower arm-to-ball joint nut. A new circlip. Once removed, these parts must not be reused during assembly. Their torque-holding ability or retention capability is diminished during removal. Remove wheelcover or hub cover from wheel and tire assembly. 2. Loosen lug nuts (1012).
2 Page 2 of 8 3. Raise vehicle on a frame contact hoist and remove the wheel and tire assembly. 4. CAUTION: Discard the front axle wheel hub retainer. It is a torque prevailing design and cannot be reused. Remove the front axle wheel hub retainer and washer. Hub Retainer Loosen Hub Retainer Removal
3 Page 3 of 8 5. For SHO only, remove wiring harness from routing clip on front shock absorber (18124). Remove air suspension height sensor (3C034) from height sensor ball studs. Position air suspension height sensor out of way. 6. Remove the front brake anti-lock sensor wire harness from the wire harness retaining clip. 7. Remove the front brake anti-lock sensor and position aside. 8. Remove and discard front suspension lower arm-to-ball joint nut. 9. Using Ball Joint Tool 211-S200 (T96P-3010-A1), Tie-Rod Remover Adapter (T81P-3504-W) and Steering Arm Remover (T64P-3590-F), press lower ball joint from front suspension lower arm (3A052). 10. Separate front suspension lower arm from lower ball joint. 11. CAUTION: Never use a hammer to separate the front wheel driveshaft joint from the hub. Damage to the front wheel driveshaft joint threads and internal components can result. Install Front Hub Tool (T81P-1104-C), Hub Adapter (T86P-1104-A1), Metric Hub Remover Set (T83P-1104-BH) and Installing Adapter (T81P-1104-A). Push front wheel driveshaft joint only to the point that the splines are free in the hub. Remove puller (assembled tools).
4 Page 4 of CAUTION: Do not allow halfshaft to hang unsupported. CAUTION: Do not damage the boots. Remove front wheel driveshaft joint from wheel hub. 13. Using a pry bar, separate inboard CV joint housing from transaxle. 14. CAUTION: Do not damage the differential seal. Carefully remove halfshaft assembly with both hands.
5 Page 5 of 8 Installation 1. Clean seal journal. Polish with fine emery paper if required. 2. CAUTION: DO NOT reuse circlip. A new circlip must be installed each time the halfshaft is removed from the vehicle. NOTE: To correctly install the circlip, start one end in the groove and work the circlip over the shaft and into the groove. This will avoid over-expanding the circlip. On RH side only, install a new circlip on the inboard CV joint housing. 3. CAUTION: Do not damage the differential seal (4B416). NOTE: A non-metallic mallet may be used to aid in seating the circlip into the differential side gear groove. If a mallet is necessary, tap only on the outboard front wheel driveshaft joint. Carefully align splines of inboard CV joint housing with the splines in the differential side gear (4236). Exerting some force, push inboard CV joint housing into differential side gear until the circlip is felt to seat in the differential side gear.
6 Page 6 of 8 Seating Retainer Clip 4. Carefully align splines of front wheel driveshaft joint (3B413) with splines in wheel hub (2C300) and push the shaft into the wheel hub as far as possible. 5. Position lower ball joint into front suspension lower arm. 6. Install and tighten a new front suspension lower arm-to-ball joint nut to Nm (50-68 lb-ft). 7. CAUTION: Install and tighten the new front axle wheel hub retainer to specification in a continuous rotation. Stopping the rotation during installation will cause the nylon lock to set incorrectly. This will cause incorrect torque readings while tightening the retainer, and lead to bearing failure. Install a new front axle wheel hub retainer every time after loosening the
7 Page 7 of 8 retainer or not installing the retainer to specification in a continuous rotation. CAUTION: Do not use power tool to tighten front axle wheel hub retainer. Use torque wrench. With steel rod inserted in brake disc (1032), install and tighten the new front axle wheel hub retainer to Nm ( lb-ft) in a continuous rotation. 8. For SHO only, install air suspension height sensor on height sensor ball studs. Install wiring harness and routing clip on front shock absorber. 9. Install front brake anti-lock sensor. Tighten retaining bolt to Nm ( lb-in). 10. Install front brake anti-lock sensor harness in the retaining clip. 11. Install tire and wheel assembly. Tighten lug nuts to Nm ( lb-ft). Install wheelcover or hub cover. 12. Lower vehicle. 13. Check and if necessary, fill transaxle to correct level with specified fluid. Refer to Section 07-01A (AX4S) or to Section 07-01B (AX4N).
8 Page 8 of 8
Page 1 of 7 Section 07-01: Transaxle, Automatic FLC REMOVAL AND INSTALLATION 1992 Tempo/Topaz Workshop Manual Differential In Vehicle Removal Before beginning the Removal procedure, perform the following
More informationHalfshaft. Special Tool(s) Differential Plug (T89P-4850-B) Differential Seal Protector Halfshaft Removal Tool
Halfshaft Special Tool(s) Differential Plug 205-294 (T89P-4850-B) Differential Seal Protector 205-461 Halfshaft Removal Tool 205-475 Hub Remover/Replacer 204-069 (T81P-1104-C) Metric Hub Remover Adapter
More information2010 Jeep Truck Compass 4WD L4-2.4L
1 of 8 3/18/2013 5:21 PM 2010 Jeep Truck Compass 4WD L4-2.4L Vehicle» Transmission and Drivetrain» Drive Axles, Bearings and Joints» Axle Shaft Assembly» Service and Repair» Half Shaft - Removal» Front
More information2004 Explorer/Mountaineer Workshop Manual
Page 1 of 6 SECTION 204-00: Suspension System 2004 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 08/05/2005 Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm
More informationREMOVAL AND INSTALLATION > HALFSHAFT
Page 1 of 14 2008 Lincoln MKZ 3.5L Eng Service Manual: REAR DRIVE HALFSHAFTS Print Date: REMOVAL AND INSTALLATION > HALFSHAFT Special Tools Illustration Tool Name Tool Number Front Hub Remover 205-D070
More informationLoosen the lug nuts. 1. Remove the center cap. 2. With the weight of the vehicle on the wheels, loosen the lug nuts.
Section 204-01B: Front Suspension 4x4 REMOVAL AND INSTALLATION 1997 F-150, F-250 Workshop Manual Wheel Hub Special Service Tool(s) Bearing Cup Replacer T80T-4000-P Seal Replacer T96T-1175-A Threaded Drawbar
More informationSee SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( )
Page 1 of 9 ARTICLE BEGINNING DESCRIPTION Front suspension uses coil springs with integral shock absorbers. Coil springs are mounted between the upper control arms and vehicle frame. A stabilizer bar controls
More informationREMOVAL AND INSTALLATION
204-00-1 Suspension System 204-00-1 REMOVAL AND INSTALLATION Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm Rear Special Tool(s) 3. Remove the parts in the order indicated in the following illustrations
More informationWheel bearing housing, removing and installing
Page 1 of 17 40-54 Wheel bearing housing, removing and installing Removing - Remove wheel trim. On light alloy wheels use puller in vehicle tool kit to remove trim cap. - Remove bolt for drive axle. WARNING!
More informationWheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles
Rear Suspension Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles All-Wheel Drive (AWD) Vehicles Front Wheel Drive (FWD) Vehicles Removal All vehicles NOTICE: Suspension fasteners are critical
More informationHalfshaft RH ( )
Page 1 of 7 (47.10.02) Special Service Tools Ball joint separator 205-754 (LRT-54-027) Halfshaft remover/replacer 204-506/1 (LRT-60-030/1) Halfshaft remover/replacer 204-506/3 (LRT-60-030/3) Retainers
More informationFront Suspension - Front Stabilizer Bar Bushing Removal and Installation
1 of 3 23/02/2012 7:34 AM Front Suspension - Front Stabilizer Bar Bushing Removal and Installation Published: 11-May-2011 Removal WARNING: Make sure to support the vehicle with axle stands. Raise and support
More informationOVERVIEW: KIT INCLUDES:
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More information1999 Toyota RAV DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2. AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2
1999-2000 DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2 DESCRIPTION & OPERATION On RAV4 models, axle shafts transfer power from transaxle to front wheels (FWD), or front and rear wheels
More information1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions
Please visit www.performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT
More informationPage 1 of 5 Section 05-03A: Axle, Front Drive, Dana Models 44 and 50 1996 Bronco/F-Series Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/19/2000 Spindle, RH and LH Shaft and Joint
More informationLower Arm ( ) Special Service Tools. Removal.
Page 1 of 6 (60.35.02) Special Service Tools Ball joint separator 205-754 (LRT-54-027) Halfshaft remover/replacer 204-506/1 (LRT-60-030/1) Halfshaft remover/replacer 204-506/3 (LRT-60-030/3) Retainers
More informationREAR HUB UNIT BEARING
2014 Subaru Forester F4-2.5L DOHC Vehicle > Steering and Suspension > Wheels and Tires > Wheel Bearing > Service and Repair > Removal and Replacement REAR HUB UNIT BEARING Rear Hub Unit Bearing REMOVAL
More informationFRONT DRIVE SHAFT COMPONENTS DS 1 DRIVE SHAFT FRONT DRIVE SHAFT FRONT DRIVE SHAFT HOLE SNAP RING. w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR
FRONT DRIVE SHAFT DRIVE LINE SHAFT COMPONENTS 1 FRONT DRIVE SHAFT HOLE SNAP RING 23 (235, 17) FRONT DRIVE SHAFT ASSEMBLY RH w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR FRONT DRIVE SHAFT ASSEMBLY LH
More information1. Loosen the left-hand strut and spring assembly top mount nuts by four turns. Loosen the wheel lug nuts.
Page 1 of 11 AXLE SHAFTS Removal (Left Side) 1. Loosen the left-hand strut and spring assembly top mount nuts by four turns. Loosen the wheel lug nuts. CAUTION: Use a socket to loosen the wheel hub retaining
More informationTION AND OPERATION Procedure revision date: 01/22/1999
TION AND OPERATION Procedure revision date: 01/22/1999 Main Components and Functions AX4S Main Components http://www.fordtechservice.dealerconnection.com/pubs/content/~wsww/~mus~len/20/sww71006.htm (1
More informationINSTALLATION INSTRUCTION 88088
INSTALLATION INSTRUCTION 88088 For Rancho Suspension Systems RS6588 & RS6589: FORD F-150 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:
More informationAXLE SHAFTS - 2.2L Toyota Celica DESCRIPTION TROUBLE SHOOTING REMOVAL, DISASSEMBLY, REASSEMBLY & INSTALLATION AXLE SHAFTS
AXLE SHAFTS - 2.2L 1994 Toyota Celica 1994 DRIVE AXLES Toyota FWD Axle Shafts Celica 2.2L 4 Cyl DESCRIPTION Axle shafts transfer power from transaxle to the front wheels. Axle shaft consists of axle shaft
More informationINSTALLATION INSTRUCTIONS 88518
INSTALLATION INSTRUCTIONS 88518 For Rancho Suspension Systems RS6518: 2009 FORD F-150 4WD READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev A IMPORTANT NOTES! WARNING:
More informationFront Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014. Axle
204-01 Front Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014 Axle 1 N620604 Axle pivot nut 2 N806859 Axle pivot bolt 3 3007 LH/ 3006 RH LH/ 3006 RH Axle Removal NOTICE:
More informationINDUSTRIES 1631 South Dixie Hwy. Building B Pompano Beach, Florida 33060
1995-2002 Lincoln Continental 38F-30-ASSY 39F-30-ASSY 4-Wheel Full Assembly All Parts are to be Installed by a Certified ASE Technician. Front Conversion: WARNING: BEFORE YOU BEGIN THE REMOVAL OR INSTALLATION,
More informationINSTALLATION INSTRUCTION 88148
INSTALLATION INSTRUCTION 88148 Rev C For Rancho Suspension Systems RS6548, RS6549 & RS6550: GM 2500HD, 2500, and 1500HD Trucks READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION
More information2007 Hummer H Driveline/Axle Wheel Drive Shafts - H3. Fastener Tightening Specifications Specification Application
2007 Driveline/Axle Wheel Drive Shafts - H3 SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Front Wheel Drive Shaft Nut 260
More informationINSTALLATION INSTRUCTION 88051
INSTALLATION INSTRUCTION 88051 For Rancho Suspension System RS6551: Chevrolet 2500 Suburban & 2500 Avalanche READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT
More informationJOINT SHAFT REMOVAL/INSTALLATION
2001 MPV 2001 - MPV - Workshop Manual - Driveline/Axle JOINT SHAFT REMOVAL/INSTALLATION Report a problem with this article Performing the following procedures without first removing the ABS wheel speed
More information1988 Jeep Truck Wrangler L L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # Date:
1988 Jeep Truck Wrangler L4-150 2.5L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # 025288 Date: 880711 Right Front Axle Shaft Seal - Installation Models 1986-88 Jeep Comanche,
More information2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES
2002-04 DRIVE AXLES Axle Shafts - Front - Ram Pickup 1500 4WD DESCRIPTION Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential
More informationAEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE
AEV30308AA Last Updated: 05/31/18 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND
More informationTOYOTA COROLLA LOWERING SPRINGS Preparation
Preparation Part Number: PTR07-02140 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 1 Hardware 4 1 Instruction Form Hardware Bag Contents Item # Quantity Reqd. Description
More information2001 Chevrolet CORVETTE
riveline Support Assembly Replacement (Automatic Transmission) 1 of 21 10/24/2012 8:58 PM 2001 Chevrolet CORVETTE Submodel: Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Driveline Support Assembly
More informationConstant velocity joints, inner
"VCC001037 EN 20120826" 1(2) Constant velocity joints, inner Special tools: 951 2619 Note! For removing drive shafts Removing drive shafts. The method is the same for the left and right drive shaft. Expose
More information2012 Taurus Workshop Manual. DISASSEMBLY AND ASSEMBLY Procedure revision date: 07/14/2011
SECTION 204-01: Front Suspension DISASSEMBLY AND ASSEMBLY Procedure revision date: 07/14/2011 Strut and Spring Assembly Material Item Silicone Brake Caliper Grease and Dielectric Compound XG-3-A Specification
More informationREAR DRIVE SHAFT (3S GTE ENGINE)
SA52 REAR DRIVE SHAFT (3SGTE ENGINE) COMPONENTS SA53 NOTICE: The axle bearing could be damaged if it is subjected to the vehicle weight, such as when moving the vehicle with the drive shaft removed. Therefore,
More information4. SEPARATE SPEED SENSOR FRONT LH (a) Remove the bolt and disconnect the speed sensor wire and flexible hose from the shock absorber assy.
OVERHAUL Refer to components: See page 304 Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN TRANSAXLE OIL (a) Using a #10 socket hexagon wrench,
More informationREMOVAL & INSTALLATION
Page 1 of 6 REMOVAL & INSTALLATION AXLE SHAFTS Removal Raise and support vehicle. Remove front wheels. Remove engine undercovers. Remove cotter pin and lock nut cap. See Fig. 2. Apply brakes and remove
More informationOVERVIEW FIGURE 1 AXLE REINFORCEMENT BRACKET INSPECTION
PAGE 1 OF 7 CERTAIN 1998-2003 MODEL YEAR WINDSTAR VEHICLES REPAIRED UNDER SAFETY RECALL 10S13 WITH REAR AXLE REINFORCEMENT BRACKETS REAR AXLE INSPECTION AND REPAIR OVERVIEW Determine if repairs completed
More informationREAR SUSPENSION. Wheel Bearing and Wheel Hub. NOTE: All-Wheel Drive (AWD) shown, Front Wheel Drive (FWD) vehicles similar.
2009 Lincoln MKS AWD V6-3.7L Vehicle > Steering and Suspension > Wheels and Tires > Wheel Hub > Service and Repair > Removal and Replacement REAR SUSPENSION Wheel Bearing and Wheel Hub NOTE: All-Wheel
More information7 Drive Shaft and Axle
7 Drive Shaft and Axle 7.1 General SPECIFICATIONS EITC0100 Drive-shaft Joint type M/T AT Outer B.J. B.J. Inner T.J. T.J. Length (Joint to joint) mm (in.) Left 380 (14.96) 349 (13.74) Right 593 (23.35)
More informationINSTALLATION INSTRUCTION 88146
INSTALLATION INSTRUCTION 88146 Rev H FOR RANCHO SUSPENSION SYSTEM RS6547: 4WD SUBURBAN/YUKON XL, 4WD TAHOE/YUKON, & 4WD AVALANCHE READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING
More informationcomponents is critical so that the splines are not damaged. NOTE: Never force the hub unit bearing assembly onto the shaft or strike with a hammer.
Automotive TechTips Volume 6 Issue 4 Part 3 of a 3-Part Series Installing a Hub Unit Bearing Assembly and Steering Knuckle Guidelines for Timken continues to lead the hub unit bearing evolution by providing
More information2012 MKT Workshop Manual. REMOVAL AND INSTALLATION Procedure revision date: 06/13/2011
SECTION 205-05: Rear Drive Halfshafts REMOVAL AND INSTALLATION Procedure revision date: 06/13/2011 Halfshaft Special Tool(s) Axle Seal Protector 205-816 Front Hub Remover 205-D070 (D93P-1175-B) or equivalent
More information1 M-3000-H4 F150 4X4 Lowering Kit
READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. IT IS RECOMMENDED THAT INSTALLATION BE DONE BY A QUALIFIED MECHANIC. REPLACE ALL STOCK PARTS THAT ARE DAMAGED OR WORN. ALWAYS WEAR EYE PROTECTION.
More informationINSTALLATION INSTRUCTIONS 88511
INSTALLATION INSTRUCTIONS 88511 For Suspension System RS6511: Ford Super Duty Requires coil spring kit RS80117 or RS80119 for a complete installation READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH
More information04-08 FORD F150 4 KIT
9257700 04-08 FORD F50 4 KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. Rough Country recommends a certified technician install this system. In addition to these instructions, professional
More informationALLDATA Online Dodge Truck Caravan V L - Front. Front
Page 1 of 10 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1994 Dodge Truck Caravan V6-201 3.3L Conversion Calculator Vehicle
More informationDecember 2004 Distributor/Dealer Service Instructions for: Safety Recall D55 Right Steering Knuckle. Models
December 2004 Distributor/Dealer Service Instructions for: Safety Recall D55 Right Steering Knuckle Models 2005 (JR) Dodge Stratus Sedan and Chrysler Sebring Sedan/Convertible NOTE: This recall applies
More informationInstallation Notes: #86000-R Race Series +3.5 L/T Kit
159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation
More informationSuperlift 3 to 4 lift system for 1998 and newer FORD RANGER 4WD with torsion bar front suspension INSTALLATION INSTRUCTIONS
FORM #9630.08-081106 PRINTED IN U.S.A. PAGE 1 OF 14 INTRODUCTION Superlift 3 to 4 lift system for 1998 and newer FORD RANGER 4WD with torsion bar front suspension INSTALLATION INSTRUCTIONS SUPERLIFT SUSPENSION
More informationSUSPENSION AND AXLE SA 1 SUSPENSION AND AXLE
SA1 SA2 Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Front Page Rear Wanders/pulls Tires worn or improperly inflated Wheel alignment incorrect Hub bearing worn Front or rear suspension
More informationSuperlift 4 lift system for 2002 and newer FORD EXPLORER SPORT TRAC 4WD with torsion bar front suspension INSTALLATION INSTRUCTIONS
INTRODUCTION Superlift 4 lift system for 2002 and newer FORD EXPLORER SPORT TRAC 4WD with torsion bar front suspension INSTALLATION INSTRUCTIONS Installation requires a professional mechanic. Prior to
More informationPRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Ford F150 4WD 4" Suspension Lift Kit
2015 Ford F150 4WD 4" Suspension Lift Kit PRE-INSTALLATION 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front Brake Line
More informationFRONT AXLE HUB SUB-ASSY LH
3038 DRIVE SHAFT / PROPELLER SHAFT REPLACEMENT HINT: COMPONENTS: SEE PAGE 304 Replace the RH side by the same procedures with LH side. 1. REMOVE FRONT WHEEL 300OI02 2. REMOVE FRONT AXLE HUB LH NUT (a)
More informationIN-VEHICLE REPAIR. Differential Bearings. Rear Drive Axle/Differential Ford 7.5-Inch Ring Gear. Special Tool(s)
205-02A-1 IN-VEHICLE REPAIR Differential Bearings Special Tool(s) Protector, Drive Pinion Thread 205-460 Special Tool(s) Installer, Differential Shim 205-220 (T85L-4067-AH) 205-02A-1 2-Jaw Puller 205-D072
More information10/31/2018 R.M. 2005::Drive Shaft / Propeller Shaft: Front Drive Shaft: Overhaul (SCION xb) 2005 Scion XB MotoLogic
2005 XB OVERHAUL Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN MANUAL TRANSAXLE OIL (M/T TRANSAXLE) Torque: 39 N m (398 kgf cm, 29 ft lbf)
More informationM-4851-M8A SUPER 8.8 IRS MUSTANG AUTOMATIC PINION FLANGE KIT
Please visit fordperformanceracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND
More informationOff-Highway Axle Planetary Wheel Ends
Maintenance Manual MM-1189 Off-Highway Axle Planetary Wheel Ends Revised 06-16 Service Notes About This Manual This manual provides service and repair procedures for planetary wheel ends on off-highway
More informationSUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically
More information1999 F-150/250 Workshop Manual
Page 1 of 30 SECTION 205-03: Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 1999 F-150/250 Workshop Manual DISASSEMBLY AND ASSEMBLY Procedure revision date: 01/08/2003 Axle Front Drive Special Tool(s)
More information2002 Taurus/Sable Workshop Manual
SECTION 211-02: Power Steering REMOVAL AND INSTALLATION 2002 Taurus/Sable Workshop Manual Power Steering Pump Pulley CII Pump Special Tool(s) Installer, Power Steering Pump Pulley 211-009 (T65P-3A733-C)
More information2005 Mustang Workshop Manual
SECTION 205-00: Driveline System General Information 2005 Mustang Workshop Manual GENERAL PROCEDURES Procedure revision date: 07/29/2004 Driveline Angle Inspection Printable View (122 KB) Special Tool(s)
More informationPage 1 of 6 Section 07-01A: Transaxle, Automatic CD4E 1996 Probe Workshop Manual REMOVAL Procedure revision date: 06/14/2000 Transaxle Item Part Number Description 1 10655 Battery 2 10732 Battery Tray
More informationFRONT AXLE AND SUSPENSION FA 1
FRONT AXLE AND SUSPENSION FA1 FRONT AXLE AND SUSPENSION FA2 FRONT AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated
More information2000 Honda Accord EX
HUB & KNUCKLE ASSEMBLY Removal (Except Odyssey & S2000) 1. Loosen lug nuts with vehicle weight on tires. Pry lock tab away from spindle nut, and loosen nut. Raise and support vehicle. Remove lug nuts and
More information1990 SUSPENSION Front ES250, LS400
SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,
More informationDifferential Bearings
SECTION 205-02B: Rear Drive Axle/Differential Ford 8.8-Inch Ring Gear 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 01/06/2010 Differential Bearings Special Tool(s) 2 Jaw Puller
More information»Product» Safety Warning
#D2500 Installation Instructions 2002-2005 Dodge Ram 1500 4WD 5" Suspension System Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad
More information1. Remove the parcel tray. For additional information, refer to Section
SECTION 204-02: Rear Suspension 2001 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/19/2003 Strut and Spring Assembly Four Door Removal CAUTION: Suspension fasteners
More informationINSTALLATION INSTRUCTIONS 89551
INSTALLATION INSTRUCTIONS 89551 For Rancho Suspension System RS66551B: Ford F250, F350 Super Duty 4x4 DIESEL ONLY (Single Rear Wheels Only With or Without Auxiliary Spring). (WILL NOT WORK ON GAS ENGINES
More informationDRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts
DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045
More informationSUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS
DN SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION - 4x2... 6 page FRONT SUSPENSION - 4x4... 14 REAR SUSPENSION... 23 ALIGNMENT TABLE OF CONTENTS page AND OPERATION WHEEL
More informationINSTALLATION INSTRUCTION 88094
INSTALLATION INSTRUCTION 88094 FOR RANCHO SUSPENSION SYSTEM RS6594B 4WD & 2WD NISSAN TITAN READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev D IMPORTANT NOTES! WARNING:
More informationSuperlift 4 lift system for FORD RANGER 4WD with torsion bar front suspension INSTALLATION INSTRUCTIONS
FORM #9909.02-072911 PRINTED IN U.S.A. PAGE 1 OF 14 INTRODUCTION Superlift 4 lift system for 1998-2009 FORD RANGER 4WD with torsion bar front suspension INSTALLATION INSTRUCTIONS Installation requires
More informationAEV30213AF Last Updated: 05/24/18. jk wrangler dualsport sc suspension right hand drive INSTALLATION GUIDE
AEV30213AF Last Updated: 05/24/18 jk wrangler 3.5 4.5 dualsport sc suspension right hand drive INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND READING
More information2002 Escape Workshop Manual
SECTION 303-01A: Engine 2.0L Zetec 2002 Escape Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/25/2004 Timing Belt Special Tool(s) Crankshaft TDC Timing Peg 303-574 (T97P-6000-A) Camshaft
More informationCHEVY C WHEEL DRIVE STANDARD CAB ONLY (EXCEPT 454SS) FTS1588-7BC 4" LIFT SPINDLES
1988-1991 CHEVY C1500 2 WHEEL DRIVE STANDARD CAB ONLY (EXCEPT 454SS) FTS1588-7BC 4" LIFT SPINDLES PARTS LIST: 1 EA. LIFT SPINDLE PASS. SIDE FT1588-7BCP 1 EA. LIFT SPINDLE DRIVER'S SIDE FT1588-7BCD 6 EA.
More information1998 Plymouth Breeze SUSPENSION' 'Rear - Cirrus, Stratus, Breeze & Sebring Convertible SUSPENSION
DESCRIPTION 1998-99 SUSPENSION Rear - Cirrus, Stratus, Breeze & Sebring Convertible Rear suspension uses a short/long arm independent design. See Fig. 1. Each side consists of a strut assembly, upper control
More information1. Remove the battery tray. For additional information, refer to Battery Tray ( )
Page 1 of 11 Removal 1. Remove the battery tray. For additional information, refer to Battery Tray (86.15.11) 2. Remove the air cleaner. For additional information, refer to Air Cleaner (19.10.05) 3. NOTE
More informationMSS SPRING KITS INSTALL GUIDE
MSS SPRING KITS INSTALL GUIDE for the Audi TT MK2 (8J) platform TO BE USED FOR REFERENCE ONLY. FOR FULL INSTALL INSTRUCTIONS, REFER TO THE AUDI WORKSHOP REPAIR GUIDE. IMPORTANT NOTICES AND NOTES: This
More information*1557BAG12* 1557BAG F /5 /6 LIFT KIT G THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS.
2015-18 F-150 4 /5 /6 LIFT KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. 92155700G *1557BAG12* 1557BAG12 Rough Country recommends a certified technician install this system. In addition
More information1984 Dodge W250 PICKUP
1984 Dodge W250 PICKUP Submodel: Engine Type: V8 Liters: 5.2 Fuel Delivery: CARB Fuel: GAS Dana 44 MODELS THROUGH 1984 2. Raise and safely support the vehicle, then remove the wheel hub and bearings as
More informationInstallation Instructions
Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to
More informationThis information covers procedures for replacing the sealant for the crankshaft cover on the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA DService Bulletin Trucks Date Group No. Page 1.2008 216 50 1(17) Sealant Crankshaft Cover, Replacement D16F Sealant Crankshaft Cover, Replacement W2005773
More informationCAUTION: Use a rag at the point you are going to pry. because aluminum alloy wheels can be easily damaged.
Front Suspension Knuckle/Hub Replacement NOTE: Use only genuine Honda aluminum wheel weights. Non-genuine aluminum wheel weights may corrode and damage aluminum wheels. Remove the center cap by prying
More informationTOYOTA 4-RUNNER KIT 5 KIT
92173600 1990-1995 TOYOTA 4-RUNNER KIT 5 KIT Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these
More informationWD CHEVY/GM LIFT
92750100 99-06 2WD CHEVY/GM 1500 3 LIFT Thank you for choosing Rough Country for all of your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these
More informationDetroit Speed, Inc. Rear Cradle Mounts Camaro P/N:
Detroit Speed, Inc. Rear Cradle Mounts 2010-15 Camaro P/N: 041510 Replace the weak, compliant factory rear cradle mounts in your 2010-15 Camaro with Detroit Speed s Solid Rear Cradle Mounts, and completely
More information»Product» Safety Warning
#F2622 Installation Instructions 1997-2003 Ford F-150 4WD 6" Suspension System Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad
More informationPage 1 of 6 Section 03-01C: Engine 3.4L SHO 1999 Taurus/Sable Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/25/1998 Intake Manifold Upper Removal 1. Disconnect battery ground cable (14301).
More informationINSTALLATION INSTRUCTION 88073
INSTALLATION INSTRUCTION 88073 Rev C FOR RANCHO SUSPENSION SYSTEMS RS6572 & RS6573: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:
More informationInstallation Instructions
Instructions Created by an: Revised 7-11-17 LRT 2005-2017 3/1 Leveling/ Lift Kit for Toyota Tacoma by Low Range Off-Road (SKU# LR-LRTACO) Installation Instructions Suggested Tools: CAUTION: Safety glasses
More information2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement
2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement Exploded View Special Tools Required Ball joint thread protector, 14 mm 071AF-S3VA000 Ball joint remover, 28 mm 07MAC-SL0A202 Hub dis/assembly tool,
More information04-08 FORD F150 6 KIT
957600 THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. 0-08 FORD F50 6 KIT Rough Country recommends a certified technician install this system. In addition to these instructions, professional
More information2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI - Removal and Installation
Page 1 of 8 Removal and Installation REMOVAL 1. REMOVE HOOD Torque: 13 Nm (130 kgf-cm, 9 ft. lbs.) 2. REMOVE BATTERY 3. REMOVE ECM AND ECM CASE Torque: 6.9 Nm (70 kgf-cm, 61 inch lbs.) 4. REMOVE ECM BRACKET
More informationE4-WM5-Y530A00 MOUNTING INSTRUCTION
IMPORTANT! READ THIS FIRST! Installation of shock absorbers requires special tools and expert knowledge. Accordingly, installation of all BILSTEIN products must be performed by a qualified suspension specialist.
More informationInstallation Instructions
Instructions Created by an: 2007-Present Toyota Tundra LRT Leveling Lift Kit - 4WD by Low Range Off-Road (SKU# LR-LRTundra) Instructions also apply to 2WD Kits. Installation Instructions Revised 7-11-17
More information