REMOVAL AND INSTALLATION > HALFSHAFT
|
|
- Raymond Eaton
- 5 years ago
- Views:
Transcription
1 Page 1 of Lincoln MKZ 3.5L Eng Service Manual: REAR DRIVE HALFSHAFTS Print Date: REMOVAL AND INSTALLATION > HALFSHAFT Special Tools Illustration Tool Name Tool Number Front Hub Remover 205-D070 (D93P-1175-B) or equivalent Halfshaft Installer (T97P-1175-A)
2 Page 2 of 14 Fig 1: Exploded View Of Halfshaft Components With Torque Specifications Item Part Number Description 1 3N405 Rear wheel hub nut 2 W S Shaft speed sensor bolt 3 2C187 Shaft speed sensor 4 W S Upper arm bolt 5 W S Upper arm nut 6 W S Tie-rod bracket nuts (4 required)
3 Page 3 of 14 7 W S Lower shock absorber bolt 8 W S Lower shock absorber nut 9 4B402 Rear halfshaft assembly REMOVAL AND INSTALLATION > HALFSHAFT > REMOVAL 1. Remove the tire and wheel. For additional information, refer to WHEELS AND TIRES article. 2. Remove and discard the rear wheel hub nut. 3. Remove the bolt and position aside the shaft speed sensor. Fig 1: Locating Shaft Speed Sensor Bolt 4. Remove the nut and lower shock absorber bolt.
4 Page 4 of 14 Fig 2: Locating Lower Shock Absorber Bolt 5. Support the lower arm. Fig 3: Supporting Lower Arm
5 Page 5 of Remove the 4 toe link bracket nuts. Fig 4: Locating Link Bracket Nuts 7. Using the special tool, separate the halfshaft from the rear axle hub assembly. Fig 5: Separating Halfshaft From Wheel Hub Using Special Tool (205-D070)
6 Page 6 of 14 CAUTION: Do not damage the oil seal protector when removing the axle halfshaft from the differential. 8. Using a suitable pry bar, remove the halfshaft. Fig 6: Removing Halfshaft Using A Suitable Pry Bar 9. Remove and discard the circlip from the stub shaft.
7 Page 7 of 14 Fig 7: Locating Halfshaft Circlip REMOVAL AND INSTALLATION > HALFSHAFT > INSTALLATION CAUTION: Make sure to install the correct circlip for each application. Failure to use the correct diameter circlip may result in shaft removal concerns or shaft separation during vehicle operation. 1. Install a new circlip on the stub shaft.
8 Page 8 of 14 Fig 1: Locating Intermediate Shaft Circlip 2. Install the stub shaft in the rear drive unit. 1. Make sure the circlip locks in the side gear.
9 Page 9 of 14 Fig 2: Installing Stub Shaft In Rear Drive Unit 3. Using the special tool, install the outer halfshaft end into the hub assembly. Fig 3: Installing Outer Halfshaft End Into Hub Assembly
10 Page 10 of Position the lower arm. Fig 4: Supporting Lower Arm CAUTION: Do not tighten the rear wheel hub nut with the vehicle on the ground. The nut must be tightened to specification before the vehicle is lowered to the ground. Wheel bearing damage will occur if the wheel bearing is loaded with the weight of the vehicle applied. 5. Install the new rear wheel hub nut. 1. To install, tighten to 255 Nm (188 lb-ft). 6. Stake the new nut in line with the keyway to a recommended minimum depth of 1 mm (0.039 in) below the keyway diameter to engage the locking feature.
11 Page 11 of 14 Fig 5: Identifying Rear Wheel Hub Nut 7. Install the 4 rear toe link bracket nuts. 1. Tighten to 90 Nm (66 lb-ft).
12 Page 12 of 14 Fig 6: Locating Link Bracket Nuts 8. Install the lower shock absorber bolt and nut. 1. Tighten to 115 Nm (85 lb-ft).
13 Page 13 of 14 Fig 7: Locating Lower Shock Absorber Bolt 9. Install the axle shaft speed sensor and bolt. 1. Tighten to 23 Nm (17 lb-ft).
14 Page 14 of 14 Fig 8: Locating Shaft Speed Sensor Bolt 10. Fill the axle with the specified quantity of the specified lubricant. 11. Install the tire and wheel. For additional information, refer to WHEELS AND TIRES article.
Halfshaft RH ( )
Page 1 of 7 (47.10.02) Special Service Tools Ball joint separator 205-754 (LRT-54-027) Halfshaft remover/replacer 204-506/1 (LRT-60-030/1) Halfshaft remover/replacer 204-506/3 (LRT-60-030/3) Retainers
More informationLower Arm ( ) Special Service Tools. Removal.
Page 1 of 6 (60.35.02) Special Service Tools Ball joint separator 205-754 (LRT-54-027) Halfshaft remover/replacer 204-506/1 (LRT-60-030/1) Halfshaft remover/replacer 204-506/3 (LRT-60-030/3) Retainers
More informationHalfshaft SPECIAL SERVICE TOOL(S) REQUIRED
Page 1 of 8 Section 05-04: Halfshaft, Front Wheel 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Halfshaft SPECIAL SERVICE TOOL(S) REQUIRED Description Tool
More informationWheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles
Rear Suspension Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles All-Wheel Drive (AWD) Vehicles Front Wheel Drive (FWD) Vehicles Removal All vehicles NOTICE: Suspension fasteners are critical
More informationREMOVAL AND INSTALLATION
204-00-1 Suspension System 204-00-1 REMOVAL AND INSTALLATION Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm Rear Special Tool(s) 3. Remove the parts in the order indicated in the following illustrations
More information2004 Explorer/Mountaineer Workshop Manual
Page 1 of 6 SECTION 204-00: Suspension System 2004 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 08/05/2005 Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm
More informationREAR SUSPENSION. Wheel Bearing and Wheel Hub. NOTE: All-Wheel Drive (AWD) shown, Front Wheel Drive (FWD) vehicles similar.
2009 Lincoln MKS AWD V6-3.7L Vehicle > Steering and Suspension > Wheels and Tires > Wheel Hub > Service and Repair > Removal and Replacement REAR SUSPENSION Wheel Bearing and Wheel Hub NOTE: All-Wheel
More informationHalfshaft. Special Tool(s) Differential Plug (T89P-4850-B) Differential Seal Protector Halfshaft Removal Tool
Halfshaft Special Tool(s) Differential Plug 205-294 (T89P-4850-B) Differential Seal Protector 205-461 Halfshaft Removal Tool 205-475 Hub Remover/Replacer 204-069 (T81P-1104-C) Metric Hub Remover Adapter
More information1. Loosen the left-hand strut and spring assembly top mount nuts by four turns. Loosen the wheel lug nuts.
Page 1 of 11 AXLE SHAFTS Removal (Left Side) 1. Loosen the left-hand strut and spring assembly top mount nuts by four turns. Loosen the wheel lug nuts. CAUTION: Use a socket to loosen the wheel hub retaining
More information2012 MKT Workshop Manual. REMOVAL AND INSTALLATION Procedure revision date: 06/13/2011
SECTION 205-05: Rear Drive Halfshafts REMOVAL AND INSTALLATION Procedure revision date: 06/13/2011 Halfshaft Special Tool(s) Axle Seal Protector 205-816 Front Hub Remover 205-D070 (D93P-1175-B) or equivalent
More informationREPAIR INSTRUCTIONS > LOWER CONTROL ARM REPLACEMENT (1500 SERIES) > TOOLS REQUIRED
Page 1 of 13 2007 GMC Yukon 5.3L Eng Base Service Manual: FRONT SUSPENSION SYSTEM Print Date: REPAIR INSTRUCTIONS > LOWER CONTROL ARM REPLACEMENT (1500 SERIES) > TOOLS REQUIRED J 43631 Ball Joint Separator.
More informationPage 1 of 7 Section 07-01: Transaxle, Automatic FLC REMOVAL AND INSTALLATION 1992 Tempo/Topaz Workshop Manual Differential In Vehicle Removal Before beginning the Removal procedure, perform the following
More informationFront Suspension - Front Stabilizer Bar Bushing Removal and Installation
1 of 3 23/02/2012 7:34 AM Front Suspension - Front Stabilizer Bar Bushing Removal and Installation Published: 11-May-2011 Removal WARNING: Make sure to support the vehicle with axle stands. Raise and support
More informationSee SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( )
Page 1 of 9 ARTICLE BEGINNING DESCRIPTION Front suspension uses coil springs with integral shock absorbers. Coil springs are mounted between the upper control arms and vehicle frame. A stabilizer bar controls
More information2000 Honda Accord EX
HUB & KNUCKLE ASSEMBLY Removal (Except Odyssey & S2000) 1. Loosen lug nuts with vehicle weight on tires. Pry lock tab away from spindle nut, and loosen nut. Raise and support vehicle. Remove lug nuts and
More information2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES
2002-04 DRIVE AXLES Axle Shafts - Front - Ram Pickup 1500 4WD DESCRIPTION Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential
More information1990 SUSPENSION Front ES250, LS400
SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,
More information2012 Taurus Workshop Manual. DISASSEMBLY AND ASSEMBLY Procedure revision date: 07/14/2011
SECTION 204-01: Front Suspension DISASSEMBLY AND ASSEMBLY Procedure revision date: 07/14/2011 Strut and Spring Assembly Material Item Silicone Brake Caliper Grease and Dielectric Compound XG-3-A Specification
More informationDIFFERENTIALS & AXLE SHAFTS
DIFFERENTIALS & AXLE SHAFTS 2001 Chevrolet Camaro 2000-01 DRIVE AXLES General Motors Differentials & Axle Shafts Chevrolet; Camaro Pontiac; Firebird DESCRIPTION & OPERATION Drive axle is a semi-floating,
More information1993 SUSPENSION Volkswagen Rear. EuroVan
Article Text ARTICLE BEGINNING 1993 SUSPENSION Volkswagen Rear EuroVan DESCRIPTION Suspension uses control arms and axle beam for stabilization. Control arms and axle beam are combined as one unit. Brake
More informationPage 1 of 5 Section 05-03A: Axle, Front Drive, Dana Models 44 and 50 1996 Bronco/F-Series Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/19/2000 Spindle, RH and LH Shaft and Joint
More information2010 Jeep Truck Compass 4WD L4-2.4L
1 of 8 3/18/2013 5:21 PM 2010 Jeep Truck Compass 4WD L4-2.4L Vehicle» Transmission and Drivetrain» Drive Axles, Bearings and Joints» Axle Shaft Assembly» Service and Repair» Half Shaft - Removal» Front
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION FRONT DISC BRAKE PADS 1. Raise and support front of vehicle. Remove wheels. Remove caliper bolt and brakeline bracket bolts. Pivot caliper aside. Remove pads and pad shim. Remove
More informationSUSPENSION - REAR Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - REAR 1988 Toyota Celica REAR SUSPENSION Toyota IRS DESCRIPTION The Toyota Independent Rear Suspension (IRS) system utilizes MacPherson struts, which fasten to axle carrier and wheel housing.
More informationDRIVE AXLES. Differentials & Axle Shafts - Corvette
DESCRIPTION & OPERATION 1998-99 DRIVE AXLES Differentials & Axle Shafts - Corvette A Getrag 625 model differential is used on both the automatic and manual transmissions. Differential carrier and case
More informationDRIVE AXLE - 4WD MODELS WITH INTEGRAL HOUSING
DRIVE AXLE - 4WD MODELS WITH INTEGRAL HOUSING 1988 Toyota Celica DRIVE AXLES Toyota Integral Housing Celica (Rear) DESCRIPTION housing. Drive axle assembly is hypoid type with integral carrier AXLE RATIO
More informationSUSPENSION - FRONT Infiniti G20 DESCRIPTION ADJUSTMENTS & INSPECTION SUSPENSION Front G20
SUSPENSION - FRONT 1992 Infiniti G20 1991-92 SUSPENSION Front G20 DESCRIPTION G20 uses a 4-wheel independent multi-link suspension system. Transverse links are connected to bottom of steering knuckle.
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Rotate engine clockwise and position cylinder No. 1 on TDC of compression stroke. Ensure "O" mark on crankshaft pulley aligns
More informationM-4851-M8A SUPER 8.8 IRS MUSTANG AUTOMATIC PINION FLANGE KIT
Please visit fordperformanceracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND
More informationOVERVIEW: KIT INCLUDES:
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More information1999 Toyota RAV DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2. AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2
1999-2000 DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2 DESCRIPTION & OPERATION On RAV4 models, axle shafts transfer power from transaxle to front wheels (FWD), or front and rear wheels
More informationARTICLE BEGINNING DESCRIPTION ADJUSTMENTS & INSPECTION SUSPENSION Rear. Golf III
Article Text ARTICLE BEGINNING 1995-96 SUSPENSION Rear Golf III DESCRIPTION Suspension uses control arms and axle beam for stabilization. Control arms and axle beam are combined as one unit. Brake drums
More informationREPAIR INSTRUCTIONS - ON VEHICLE
2013 TRANSMISSION Automatic Transmission - 6T40 - Repair Instructions - On Vehicle - Orlando REPAIR INSTRUCTIONS - ON VEHICLE MANUAL SHIFT DETENT LEVER WITH SHAFT POSITION SWITCH ASSEMBLY REPLACEMENT Special
More informationTechnical Service Bulletin
2008 Santafe Report a problem with this article Subject Technical Service Bulletin Group Number CHASSIS 10-SS-004 Date REAR HUB BEARING REPLACEMENT 4WD FEBRUARY, 2010 Model 07-09MY SANTA FE (CM) CIRCULATE
More informationSUSPENSION. Front - Corvette
1998-99 SUSPENSION Front - Corvette DESCRIPTION The major suspension components are made of high-strength, lightweight, forged aluminum alloy. A fiberglass single-leaf spring is mounted transversely below
More informationPage 1 of 9 FRONT AXLE HUB & WHEEL BEARING Removal (Avalon, Camry, Camry Solara & Sienna) 1. 2. 3. 4. 5. 6. 7. 8. Remove front wheel. Check wheel bearing backlash and deviation (rotational free play).
More information303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine
2010 MKZ Report a problem with this article 303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid REMOVAL Procedure revision date: 10/19/2012 Engine Special Tool(s) 2,200# Floor Crane,
More informationSUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically
More informationDRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts
DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045
More information1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series
1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet
More informationCAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.
REMOVAL Timing Chain 1. Disconnect negative battery cable. 2. Drain cooling system. 3. Remove upper intake manifold. 4. Remove cylinder head covers, crankshaft vibration damper, and timing chain cover.
More information2003 Ford Focus ZTW SUSPENSION Front - Focus
HUB/STEERING KNUCKLE ASSEMBLY Removal 1. Loosen the strut tower nuts by at least five turns. See Fig. 4. Loosen the wheel hub retaining nut. Raise and support vehicle. Remove front wheel, brake caliper
More information1988 Jeep Truck Wrangler L L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # Date:
1988 Jeep Truck Wrangler L4-150 2.5L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # 025288 Date: 880711 Right Front Axle Shaft Seal - Installation Models 1986-88 Jeep Comanche,
More information2007 Hummer H Driveline/Axle Wheel Drive Shafts - H3. Fastener Tightening Specifications Specification Application
2007 Driveline/Axle Wheel Drive Shafts - H3 SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Front Wheel Drive Shaft Nut 260
More informationDIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING SUSPENSION AND STEERING SYSTEM 2007 SUSPENSION Suspension - Nitro CONDITION POSSIBLE CAUSES CORRECTION FRONT END NOISE 1. Loose or worn wheel bearings. 1. Replace wheel bearings.
More informationM-FR3-FA Fiesta Handling Pack INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More information1999 Volvo V70 AWD ENGINE PERFORMANCE Removal & Installation - Except S40 & V40
Removal (S70, V70 AWD & V70 XC) 1. Drain fuel tank. See DRAINING FUEL TANK (C70, S70 & V70). Drain fuel system. 2. Remove front and rear cargo compartment floor. Unplug ABS sensor and fuel gauge connectors.
More informationFRONT AXLE SECTION FAX CONTENTS TRANSMISSION & DRIVELINE FAX-1 SYMPTOM DIAGNOSIS... 2 ON-VEHICLE REPAIR... 7 PRECAUTION... 3
TRANSMISSION & DRIVELINE SECTION FAX A FRONT AXLE B C FAX CONTENTS E SYMPTOM DIAGNOSIS... 2 NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING... 2 NVH Troubleshooting Chart...2 PRECAUTION... 3 PRECAUTIONS...
More informationDRIVE AXLE - INTEGRAL HOUSING
DRIVE AXLE - INTEGRAL HOUSING 1993 Toyota Celica 1993 DRIVE AXLES Toyota Differentials & Axle Shafts - Integral Housing Toyota; Celica All-Trac DESCRIPTION Drive axle assembly is a hypoid type with integral
More informationMANUAL TRANSMISSIONS. Servicing - Corvette. Transmission Model (RPO Code) Borg-Warner T56 6-Speed (M12)
2003-04 MANUAL TRANSMISSIONS Servicing - Corvette APPLICATION TRANSMISSION APPLICATION Application Corvette Convertible & Coupe Z06 Transmission Model (RPO Code) Borg-Warner T56 6-Speed (MM6) Borg-Warner
More informationIN-VEHICLE REPAIR. Differential Bearings. Rear Drive Axle/Differential Ford 7.5-Inch Ring Gear. Special Tool(s)
205-02A-1 IN-VEHICLE REPAIR Differential Bearings Special Tool(s) Protector, Drive Pinion Thread 205-460 Special Tool(s) Installer, Differential Shim 205-220 (T85L-4067-AH) 205-02A-1 2-Jaw Puller 205-D072
More informationIf it exceeds the maximum specification, replace the propeller shaft.
If it exceeds the maximum specification, replace the propeller shaft. Maximum runout o 0.4 mm {0.016 in} 2. Inspect the play and rotation of the joint by turning the universal joint in the directions shown
More informationPage 1 of 6 Axle Shaft, Hub, Oil Seal and Outer Wheel Bearing SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Locknut Wrench T85T-4252-AH Removal 1. Set the parking brake and loosen the eight
More information1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions
Please visit www.performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT
More informationInspection and Verification, Ranger
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk53a03.htm~gen~ref.htm Page 1 of 1 Section 05-03A: Wheel Hubs and Bearings, Front Wheels, 4- Wheel Drive DIAGNOSIS AND TESTING 1997 Ranger 4x4 with Dana
More informationDifferential Bearings
SECTION 205-02B: Rear Drive Axle/Differential Ford 8.8-Inch Ring Gear 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 01/06/2010 Differential Bearings Special Tool(s) 2 Jaw Puller
More informationDifferential Bearings
SECTION 205-02A: Rear Drive Axle/Differential Ford 7.5-Inch Ring Gear 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 04/02/2009 Differential Bearings Special Tool(s) 2 Jaw Puller
More information6.0 Liter Timing Chain, Crankshaft Sprocket, Camshaft Position Actuator, and Solenoid Valve Replacement
Special Tools EN 46330 Timing Belt Tensioner Retaining Pin J 8433 Two Jaw Puller J 41478 Crankshaft Front Oil Seal Installer J 41558 Crankshaft Sprocket Remover J 41665 Crankshaft Balancer and Sprocket
More informationTH!NK neighbor Section 3 Powertrain Section 3 Powertrain
General Specifications... 2 Torque Specifications... 2 Description and Operation... 3 Diagnosis and Testing... 3 Halfshafts... 3 Motor... 3 Motor Controller... 3 Potentiometer... 3 Gearbox... 4 Removal
More information7 Drive Shaft and Axle
7 Drive Shaft and Axle 7.1 General SPECIFICATIONS EITC0100 Drive-shaft Joint type M/T AT Outer B.J. B.J. Inner T.J. T.J. Length (Joint to joint) mm (in.) Left 380 (14.96) 349 (13.74) Right 593 (23.35)
More informationSECTION Front Drive Axle/Differential
205-03-i Front Drive Axle/Differential 205-03-i SECTION 205-03 Front Drive Axle/Differential CONTENTS PAGE Axle... 205-03-2 205-03-2 Front Drive Axle/Differential 205-03-2 Axle Special Tool(s) C-Frame
More informationAEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE
AEV30308AA Last Updated: 05/31/18 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND
More informationDRIVE SHAFT LOCATION INDEX
DRIVE SHAFT LOCATION INDEX 2005 DRIVELINE/AXLE Drive Shaft - MX-5 Miata Fig. 1: Identifying Drive Shaft Location DRIVE SHAFT PRE-INSPECTION 1. Inspect the dust boot on the drive shaft for cracks, damage,
More informationSteering Gear Replacement
Page 1 of 7 Steering Gear Replacement Removal Procedure Notice: With wheels of the vehicle facing straight ahead, secure the steering wheel utilizing steering column anti-rotation pin, steering column
More information1997 Mazda MX-5 Miata SUSPENSION Front - Miata
1997-2000 SUSPENSION Front - Miata DESCRIPTION NOTE: Mazda did not produce 1998 Miata models. Front suspension is an independent, double wishbone design using upper and lower control arms. A spring over
More informationConstant velocity joints, inner
"VCC001037 EN 20120826" 1(2) Constant velocity joints, inner Special tools: 951 2619 Note! For removing drive shafts Removing drive shafts. The method is the same for the left and right drive shaft. Expose
More information1993 Jeep Grand Cherokee. WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES 1993 WHEEL ALIGNMENT Chrysler Corp. - Specifications & Procedures
ADJUSTMENTS CAMBER MEASUREMENT Check camber to determine if any components are bent or damaged. Camber angle is NOT adjustable. If angle is not to specification, components causing problem must be replaced.
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Noting position for installation reference, disconnect secondary wires from spark plugs. Remove spark plugs. 2. Disconnect negative battery cable. Remove air
More informationDetroit Speed, Inc. Rear Cradle Mounts Camaro P/N:
Detroit Speed, Inc. Rear Cradle Mounts 2010-15 Camaro P/N: 041510 Replace the weak, compliant factory rear cradle mounts in your 2010-15 Camaro with Detroit Speed s Solid Rear Cradle Mounts, and completely
More information1991 Mazda MX-5 Miata. STARTER - DIRECT DRIVE ELECTRICAL Mazda Starters - Direct Drive ELECTRICAL Mazda Starters - Direct Drive
DESCRIPTION STARTER - DIRECT DRIVE 1990-92 ELECTRICAL Mazda Starters - Direct Drive Nippondenso direct drive starter is a conventional 12-volt, 4-pole, brush-type starter. The integral solenoid is attached
More informationCHEVY / GMC 1500HD / 2500HD 2WD 8 LUG 7 BASIC KIT
85101 2000-2010 CHEVY / GMC 1500HD / 2500HD 2WD 8 LUG 7 BASIC KIT C8510-4 MAIN BOX KIT W/ HARDWARE 1) FRONT X MEMBER 1) REAR X MEMBER 2) TORSION BAR DROPS 1) LEFT BUMP STOP 1) RIGHT BUMP STOP 2) SWAY BAR
More informationFRONT WHEEL ALIGNMENT
2 Front: B A A Rear: C D Front SUENSION FRONT WHEEL ALIGNMENT D F046082E03 B FRONT WHEEL ALIGNMENT ADJUSTMENT 1. INECT TIRE (a) Inspect the tires (see page TW-3). 2. MEASURE VEHICLE HEIGHT Standard vehicle
More information2000 F-Super Duty /Excursion/F-53 Motorhome Chassis Workshop Manual
Page 1 of 6 SECTION 205-02E: Wheel Hubs and Bearings Full Floating Axle Ford 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual REMOVAL AND INSTALLATION Procedure revision date:
More informationFront Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014. Axle
204-01 Front Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014 Axle 1 N620604 Axle pivot nut 2 N806859 Axle pivot bolt 3 3007 LH/ 3006 RH LH/ 3006 RH Axle Removal NOTICE:
More informationService Bulletin No. 3033
MODEL TYPE SECTION/GROUP DATE G Series Coaches Product Improvement 2--Rear Axle Mar. 31, 2010 SUBJECT CONDITIONS BEARING BOX Parts may be purchased from MCI Service Parts, Louisville, Kentucky or from
More informationA proportioning valve is used to regulate brake pressure between front and rear brakes. Rear brakes on all models are self-adjusting.
Page 1 of 21 ARTICLE BEGINNING DESCRIPTION & OPERATION WARNING: For warnings and procedures regarding vehicles equipped with Anti- Lock Brake Systems (ABS), see ANTI-LOCK BRAKE SYSTEM article in the BRAKES
More informationFRONT SUSPENSION GROUP 2 FRONT SUSPENSION 2-1 CONTENTS SPECIFICATIONS VC-1, VC-2, VC-3 VY-1 TOOL LIST. Page
GROUP 2 FRONT SUSPENSION CONTENTS Page Specifications 1 Tool List.... 1 Torque Reference 2 Preparation for Measuring Front End Alignment... 2 Front Suspension Height Adjustment 3 Front Suspension Alignment
More informationThis file is available for free download at
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
More informationTECHNICAL SERVICE BULLETIN. Model Suzuki Swift GA/GS/GT, Sidekick JA/KX/JLX Group Miscellaneous Bulletin No. TS Date December, 1992
!"" #$%!& '(!(()(*+,-. TECHNICAL SERVICE BULLETIN Model 1990-93 Suzuki Swift GA/GS/GT, Sidekick JA/KX/JLX Group Miscellaneous Bulletin No. TS 7-04 11192 Date December, 1992 CONDITION: Change in front housing
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION REAR BRAKE CALIPER NOTE: For rear disc pad removal and installation, DO NOT disconnect brake hose from caliper (wire aside). Replace all pads on an axle if wear indicator on any
More informationSteering Gearbox Disassembly
Steering Gearbox Disassembly Steering Rack Disassembly 5. Unbend the lock washer. Before disassembling the gearbox, wash it off with solvent and a brush. Do not dip seals and O-rings in solvent. 1. Remove
More informationOVERVIEW: KIT INCLUDES:
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationMANUAL TRANSMISSIONS Mitsubishi F4M20, F5M20, F5M30 & KM200 Series TRANSMISSION APPLICATION
Article Text ARTICLE BEGINNING MANUAL TRANSMISSIONS Mitsubishi F4M20, F5M20, F5M30 & KM200 Series APPLICATION TRANSMISSION APPLICATION Vehicle Application Transmission Model Chrysler Motors (2WD) 4-Speed
More informationBRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS
BRAKE SYSTEM 1988 Toyota Celica 1988-89 BRAKES Toyota Celica, Corolla, MR2, Tercel DESCRIPTION The hydraulic brake system uses a tandem master cylinder with a vacuum power assist servo. MR2 and some Celica
More informationDESCRIPTION & OPERATION
STARTER - REDUCTION GEAR 1997 STARTING & CHARGING SYSTEMS Mazda - Starters - Reduction Gear DESCRIPTION & OPERATION Reduction gear starter is a conventional 12-volt, 4-pole, brush-type starter. The integral
More informationINDEX GENERAL. Page Connecting Rod 2M-3 Front Wheel Alignment 2M-4 Front Wheel Shimmy 2M-5 General 2M-1
INDEX Page Connecting Rod 2M-3 Front Wheel Alignment 2M-4 Front Wheel Shimmy 2M-5 General 2M-1 Pago Specifications 21-8 Steering Damper 2M-3 Steering Wheel Spoke Alignment 2M-5 Tie Rod 2M-3 GENERAL The
More informationFRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX
D DRIVELINE/AXLE A SECTION FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Precautions... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION, AND HARSHNESS (NVH)
More informationFRONT AXLE - 9 1/4 AA
DR FRONT AXLE - 9 1/4 AA 3-45 FRONT AXLE - 9 1/4 AA TABLE OF CONTENTS page FRONT AXLE - 9 1/4 AA DESCRIPTION......................... 45 OPERATION........................... 45 DIAGNOSIS AND TESTING................
More informationSTEERING LOCATION INDEX
STEERING LOCATION INDEX 2007 STEERING Power Steering - MX-5 Miata Fig. 1: Identifying Location Of Steering Components AIR BLEEDING CAUTION: Do not turn the steering wheel during the fluid level inspection,
More informationINSTALLATION INSTRUCTION 88088
INSTALLATION INSTRUCTION 88088 For Rancho Suspension Systems RS6588 & RS6589: FORD F-150 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:
More information1992 Clutch. Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT
Article Text ARTICLE BEGINNING 1992 Clutch Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT DESCRIPTION All clutches are single disc type. Pressure plate assembly uses a diaphragm spring to engage
More information1997 Mazda MX-5 Miata. STARTER - DIRECT DRIVE 1997 STARTING & CHARGING SYSTEMS Mazda - Starters - Direct Drive
STARTER - DIRECT DRIVE 1997 STARTING & CHARGING SYSTEMS Mazda - Starters - Direct Drive DESCRIPTION & OPERATION Direct drive starter is a conventional 12-volt, 4-pole, brush-type starter. The integral
More information1994 Mazda MX-5 Miata. STARTER - DIRECT DRIVE 1994 ELECTRICAL Mazda Starter - Direct Drive
DESCRIPTION STARTER - DIRECT DRIVE 1994 ELECTRICAL Mazda Starter - Direct Drive Nippondenso direct drive starter is a conventional 12-volt, 4-pole, brush-type starter. The integral solenoid is attached
More informationFRONT AXLE SECTION FAX CONTENTS TRANSMISSION & DRIVELINE FAX-1 PRECAUTION... 2 REMOVAL AND INSTALLATION... 6 PREPARATION... 3
TRANSMISSION & DRIVELINE SECTION FAX A FRONT AXLE B C FAX CONTENTS E PRECAUTION... 2 PRECAUTIONS... 2 Precaution...2 PREPARATION... 3 PREPARATION... 3 Special Service Tool...3 Commercial Service Tool...3
More informationR Removal/installation recommendations
R166.13 Removal/installation recommendations CITROËN: PEUGEOT: Berlingo (M49, M59), BX, Xantia (I and II), Xsara (Picasso, FL), ZX 205, 206, 305 (II), 306 (I and II), 309 (I and II), 405, Restyling, 406,
More informationDRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I
DRIVE AXLE 1990 Nissan 240SX 1990 DRIVE AXLES Rear Axle - R200 240SX, 300ZX DESCRIPTION & OPERATION The axle assembly is a hypoid type gear with integral carrier housing. The pinion bearing preload adjustment
More informationDifferential Ring And Pinion
SECTION 205-02B: Rear Drive Axle/Differential Ford 8.8-Inch Ring Gear 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 01/06/2010 Differential Ring And Pinion Special Tool(s) 2 Jaw
More informationHGM-E LSHT Wheel Motor Service and Repair Manual
HGM-E LSHT Wheel Motor Service and Repair Manual BLN-52198 January 2018 Table Of Contents Foreword... 1 How to use this manual... 2 General Instructions... 2 General Description... 2 Tools... 3 Torques...
More informationSCION tc LOWERING SPRINGS Preparation
Preparation Part Number: PTR11-21100 PTR11-21100-50 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 2 Locking Nut 4 2 Spring Bumper, Front 5 1 Instruction Form Hardware
More informationTOYOTA COROLLA LOWERING SPRINGS Preparation
Preparation Part Number: PTR07-02140 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 1 Hardware 4 1 Instruction Form Hardware Bag Contents Item # Quantity Reqd. Description
More information