Size: px
Start display at page:

Download ""

Transcription

1 Page 1 of 7 Section 07-01: Transaxle, Automatic FLC REMOVAL AND INSTALLATION 1992 Tempo/Topaz Workshop Manual Differential In Vehicle Removal Before beginning the Removal procedure, perform the following preliminary Steps: Position vehicle on a hoist. Refer to the Pre-Delivery manual, Section Raise hood. Position fender covers. Disconnect battery ground cable. 1. Remove bolts attaching managed air valve-to-transaxle valve body cover, if so equipped. 2. Remove bolt that retains Thermactor hoses. CAUTION: Position hoses and valve away from brake tubing and master cylinder to avoid interference when raising transaxle. 3. Raise vehicle on a hoist. Remove front wheels and tires. Refer to Section Remove nuts from control arm ball joint pinch bolts. Drive bolts out of the knuckles using a punch and hammer. CAUTION: The nuts and bolts must be discarded. 4. Remove brake hose clip retaining bolts. 5. Remove tie rod-to-steering knuckle retaining nuts. 6. Disengage control arms from steering knuckles.

2 Page 2 of 7 CAUTION: Do not use a hammer on knuckle to remove ball joints. NOTE: The plastic shield installed behind the rotor contains a moulded pocket into which the lower control arm ball joint fits. When disengaging the control arm from the knuckle, clearance for the ball joint can be provided by bending the shield back toward the rotor. Failure to provide clearance for the ball joint may result in damage to the shield. NOTE: Exercise care not to damage or cut ball joint boot. Pry bar must not contact lower arm. 7. Remove 13 transaxle oil pan retaining bolts. Remove pan, drain fluid and discard gasket. 8. To remove halfshafts, insert a large-blade screwdriver between differential pinion shaft and inboard CV joint stub shaft. Give a sharp tap to handle end of screwdriver to dislodge circlip from side gear, freeing halfshaft from the differential. CAUTION: Care should be taken not to damage differential seals or bottom pan during halfshaft removal. 9. Pull halfshaft out of transaxle. Support end of shaft by suspending from a convenient underbody component with a length of wire. NOTE: Do not allow the shaft to hang unsupported as damage to the CV joints may result.

3 Page 3 of Remove three oil filter retaining bolts and remove filter. Thoroughly clean filter. Discard seal. 11. Position Rotunda Hi-Lift Jack or equivalent under rear oil pan rail of transaxle case. Place a wood block between jack and case to protect oil pan and case mating surface. CAUTION: Extreme care should be taken not to damage transaxle case. 12. With jack supporting transaxle, remove two motor mount-to-transaxle retaining bolts. Remove rear mount assembly. 13. Remove six differential bearing retainer retaining bolts. 14. Raise Rotunda Hi-Lift Jack or equivalent to allow clearance for bearing retainer removal. Remove bearing retainer and shim while supporting differential.

4 Page 4 of Move differential assembly to the left to clear differential bearing. Remove from transaxle case. Installation NOTE: If the differential case, bearing retainer, or differential bearing is replaced, reshimming will be required. Refer to Differential Ball Bearing End Play. 1. Raise Rotunda Hi-Lift Jack or equivalent high enough to allow installation of bearing retainer. CAUTION: Extreme care must be taken not to damage transaxle case. NOTE: Inspect both differential seals for any evidence of damage. Replace, if necessary, prior to differential installation. 2. Install differential, shims, and bearing retainer using new O-ring seal or gasket. 3. Apply Threadlock and Sealer E0AZ AA (ESE-M4G204-A) or equivalent to threads of bearing retainer retaining bolts. Install bolts. Tighten to Nm (15-19 lb-ft). 4. Lower jack far enough to install rear motor mount on transaxle. Install two mount retaining bolts. Tighten to Nm (31-44 lb-ft).

5 Page 5 of 7 5. Install two support bracket retaining nuts. Tighten nuts to Nm (45-64 lb-ft). Remove jack. 6. Install new circlips on inboard CV joint stub shafts. NOTE: To install the circlip properly, start on end in the groove and work the circlip over the stub shaft end and into the groove. This will avoid over-expanding the circlip. CAUTION: The circlip must not be reused. A new circlip must be installed each time the inboard CV joint is installed into the transaxle differential. 7. Carefully align splines of inboard CV joint stub shaft with splines in differential. Exerting some force, push CV joint into differential until circlip is felt to seat in differential side gear. Use care to prevent damage to differential oil seal. CAUTION: Install Transaxle Plug T81P-1177-B or equivalent to ensure alignment of CV joint stub shaft with side gear. NOTE: A non-metallic mallet may be used to aid in seating the circlip into the differential side gear groove. If a mallet is necessary, tap only on the outboard CV joint stub shaft. 8. Position a new seal on filter and install filter. Install filter retaining bolts. Tighten to 9-12Nm (7-9 lb-ft).

6 Page 6 of 7 9. Install new oil pan gasket. 10. Install oil pan and 13 retaining bolts. Tighten alternately to Nm (15-19 lb-ft). 11. Connect control arms to steering knuckles and install new nuts and bolts. Tighten nuts to Nm (40-54 lb-ft). CAUTION: New bolts and nuts must be installed. 12. Position brake hose routing clip on suspension strut and install retaining bolt. Tighten bolt to 11 Nm (8 lb-ft).

7 Page 7 of Install steering gear tie rods to steering knuckles using new nuts and cotter pins. 14. Install wheels and tires. Lower vehicle. Tighten wheel lug nuts to Nm ( lb-ft). 15. Install managed air valve to transaxle valve body cover retaining bolts, if so equipped. 16. Install bolt retaining Thermactor hoses. 17. Connect battery ground cable. 18. Fill transaxle to the proper level as outlined.

Halfshaft SPECIAL SERVICE TOOL(S) REQUIRED

Halfshaft SPECIAL SERVICE TOOL(S) REQUIRED Page 1 of 8 Section 05-04: Halfshaft, Front Wheel 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Halfshaft SPECIAL SERVICE TOOL(S) REQUIRED Description Tool

More information

2010 Jeep Truck Compass 4WD L4-2.4L

2010 Jeep Truck Compass 4WD L4-2.4L 1 of 8 3/18/2013 5:21 PM 2010 Jeep Truck Compass 4WD L4-2.4L Vehicle» Transmission and Drivetrain» Drive Axles, Bearings and Joints» Axle Shaft Assembly» Service and Repair» Half Shaft - Removal» Front

More information

Halfshaft. Special Tool(s) Differential Plug (T89P-4850-B) Differential Seal Protector Halfshaft Removal Tool

Halfshaft. Special Tool(s) Differential Plug (T89P-4850-B) Differential Seal Protector Halfshaft Removal Tool Halfshaft Special Tool(s) Differential Plug 205-294 (T89P-4850-B) Differential Seal Protector 205-461 Halfshaft Removal Tool 205-475 Hub Remover/Replacer 204-069 (T81P-1104-C) Metric Hub Remover Adapter

More information

1999 Toyota RAV DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2. AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2

1999 Toyota RAV DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2. AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2 1999-2000 DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2 DESCRIPTION & OPERATION On RAV4 models, axle shafts transfer power from transaxle to front wheels (FWD), or front and rear wheels

More information

Front Suspension - Front Stabilizer Bar Bushing Removal and Installation

Front Suspension - Front Stabilizer Bar Bushing Removal and Installation 1 of 3 23/02/2012 7:34 AM Front Suspension - Front Stabilizer Bar Bushing Removal and Installation Published: 11-May-2011 Removal WARNING: Make sure to support the vehicle with axle stands. Raise and support

More information

2003 Escape Workshop Manual

2003 Escape Workshop Manual Page 1 of 6 SECTION 211-02: Power Steering 2003 Escape Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/06/2005 Steering Gear Printable View (633 KB) Special Tool(s) Tie-Rod End Remover

More information

AXLE SHAFTS - 2.2L Toyota Celica DESCRIPTION TROUBLE SHOOTING REMOVAL, DISASSEMBLY, REASSEMBLY & INSTALLATION AXLE SHAFTS

AXLE SHAFTS - 2.2L Toyota Celica DESCRIPTION TROUBLE SHOOTING REMOVAL, DISASSEMBLY, REASSEMBLY & INSTALLATION AXLE SHAFTS AXLE SHAFTS - 2.2L 1994 Toyota Celica 1994 DRIVE AXLES Toyota FWD Axle Shafts Celica 2.2L 4 Cyl DESCRIPTION Axle shafts transfer power from transaxle to the front wheels. Axle shaft consists of axle shaft

More information

FRONT DRIVE SHAFT COMPONENTS DS 1 DRIVE SHAFT FRONT DRIVE SHAFT FRONT DRIVE SHAFT HOLE SNAP RING. w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR

FRONT DRIVE SHAFT COMPONENTS DS 1 DRIVE SHAFT FRONT DRIVE SHAFT FRONT DRIVE SHAFT HOLE SNAP RING. w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR FRONT DRIVE SHAFT DRIVE LINE SHAFT COMPONENTS 1 FRONT DRIVE SHAFT HOLE SNAP RING 23 (235, 17) FRONT DRIVE SHAFT ASSEMBLY RH w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR FRONT DRIVE SHAFT ASSEMBLY LH

More information

INDUSTRIES 1631 South Dixie Hwy. Building B Pompano Beach, Florida 33060

INDUSTRIES 1631 South Dixie Hwy. Building B Pompano Beach, Florida 33060 1995-2002 Lincoln Continental 38F-30-ASSY 39F-30-ASSY 4-Wheel Full Assembly All Parts are to be Installed by a Certified ASE Technician. Front Conversion: WARNING: BEFORE YOU BEGIN THE REMOVAL OR INSTALLATION,

More information

10/31/2018 R.M. 2005::Drive Shaft / Propeller Shaft: Front Drive Shaft: Overhaul (SCION xb) 2005 Scion XB MotoLogic

10/31/2018 R.M. 2005::Drive Shaft / Propeller Shaft: Front Drive Shaft: Overhaul (SCION xb) 2005 Scion XB MotoLogic 2005 XB OVERHAUL Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN MANUAL TRANSAXLE OIL (M/T TRANSAXLE) Torque: 39 N m (398 kgf cm, 29 ft lbf)

More information

2004 Explorer/Mountaineer Workshop Manual

2004 Explorer/Mountaineer Workshop Manual Page 1 of 6 SECTION 204-00: Suspension System 2004 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 08/05/2005 Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm

More information

1990 SUSPENSION Front ES250, LS400

1990 SUSPENSION Front ES250, LS400 SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,

More information

1988 Jeep Truck Wrangler L L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # Date:

1988 Jeep Truck Wrangler L L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # Date: 1988 Jeep Truck Wrangler L4-150 2.5L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # 025288 Date: 880711 Right Front Axle Shaft Seal - Installation Models 1986-88 Jeep Comanche,

More information

REMOVAL AND INSTALLATION > HALFSHAFT

REMOVAL AND INSTALLATION > HALFSHAFT Page 1 of 14 2008 Lincoln MKZ 3.5L Eng Service Manual: REAR DRIVE HALFSHAFTS Print Date: REMOVAL AND INSTALLATION > HALFSHAFT Special Tools Illustration Tool Name Tool Number Front Hub Remover 205-D070

More information

REMOVAL AND INSTALLATION

REMOVAL AND INSTALLATION 204-00-1 Suspension System 204-00-1 REMOVAL AND INSTALLATION Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm Rear Special Tool(s) 3. Remove the parts in the order indicated in the following illustrations

More information

Page 1 of 6 Section 07-01A: Transaxle, Automatic CD4E 1996 Probe Workshop Manual REMOVAL Procedure revision date: 06/14/2000 Transaxle Item Part Number Description 1 10655 Battery 2 10732 Battery Tray

More information

4. SEPARATE SPEED SENSOR FRONT LH (a) Remove the bolt and disconnect the speed sensor wire and flexible hose from the shock absorber assy.

4. SEPARATE SPEED SENSOR FRONT LH (a) Remove the bolt and disconnect the speed sensor wire and flexible hose from the shock absorber assy. OVERHAUL Refer to components: See page 304 Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. 1. DRAIN TRANSAXLE OIL (a) Using a #10 socket hexagon wrench,

More information

OVERVIEW: KIT INCLUDES:

OVERVIEW: KIT INCLUDES: Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

Halfshaft RH ( )

Halfshaft RH ( ) Page 1 of 7 (47.10.02) Special Service Tools Ball joint separator 205-754 (LRT-54-027) Halfshaft remover/replacer 204-506/1 (LRT-60-030/1) Halfshaft remover/replacer 204-506/3 (LRT-60-030/3) Retainers

More information

REAR DRIVE SHAFT (3S GTE ENGINE)

REAR DRIVE SHAFT (3S GTE ENGINE) SA52 REAR DRIVE SHAFT (3SGTE ENGINE) COMPONENTS SA53 NOTICE: The axle bearing could be damaged if it is subjected to the vehicle weight, such as when moving the vehicle with the drive shaft removed. Therefore,

More information

FRONT AXLE AND SUSPENSION FA 1

FRONT AXLE AND SUSPENSION FA 1 FRONT AXLE AND SUSPENSION FA1 FRONT AXLE AND SUSPENSION FA2 FRONT AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated

More information

2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES

2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES 2002-04 DRIVE AXLES Axle Shafts - Front - Ram Pickup 1500 4WD DESCRIPTION Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential

More information

Page 1 of 5 Section 05-03A: Axle, Front Drive, Dana Models 44 and 50 1996 Bronco/F-Series Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/19/2000 Spindle, RH and LH Shaft and Joint

More information

1996 Aerostar/Ranger/Explorer

1996 Aerostar/Ranger/Explorer Page 1 of 10 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch

More information

AEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE

AEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE AEV30308AA Last Updated: 05/31/18 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND

More information

SUSPENSION AND AXLE SA 1 SUSPENSION AND AXLE

SUSPENSION AND AXLE SA 1 SUSPENSION AND AXLE SA1 SA2 Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Front Page Rear Wanders/pulls Tires worn or improperly inflated Wheel alignment incorrect Hub bearing worn Front or rear suspension

More information

FRONT & REAR AXLE SECTIONAX CONTENTS. FRONT AXLE...2 Precautions...2

FRONT & REAR AXLE SECTIONAX CONTENTS. FRONT AXLE...2 Precautions...2 FRONT & REAR AXLE SECTIONAX CONTENTS FRONT AXLE...2 Precautions...2 PRECAUTIONS...2 Preparation...2 SPECIAL SERVICE TOOLS...2 COMMERCIAL SERVICE TOOLS...2 Noise, Vibration and Harshness (NVH) Troubleshooting...3

More information

2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement

2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement 2007 PILOT - Front Knuckle/Hub/Wheel Bearing Replacement Exploded View Special Tools Required Ball joint thread protector, 14 mm 071AF-S3VA000 Ball joint remover, 28 mm 07MAC-SL0A202 Hub dis/assembly tool,

More information

Removing/installing final drive

Removing/installing final drive 1(16) Removing/installing final drive Special tools: 998 5972, 999 5561, 999 5652, 999 5659, 999 5660 Removing Note! Position the rear lifting arms on the arrows on the sills. This is so the support arm

More information

1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions

1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions Please visit www.performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT

More information

CHEVY C WHEEL DRIVE STANDARD CAB ONLY (EXCEPT 454SS) FTS1588-7BC 4" LIFT SPINDLES

CHEVY C WHEEL DRIVE STANDARD CAB ONLY (EXCEPT 454SS) FTS1588-7BC 4 LIFT SPINDLES 1988-1991 CHEVY C1500 2 WHEEL DRIVE STANDARD CAB ONLY (EXCEPT 454SS) FTS1588-7BC 4" LIFT SPINDLES PARTS LIST: 1 EA. LIFT SPINDLE PASS. SIDE FT1588-7BCP 1 EA. LIFT SPINDLE DRIVER'S SIDE FT1588-7BCD 6 EA.

More information

Loosen the lug nuts. 1. Remove the center cap. 2. With the weight of the vehicle on the wheels, loosen the lug nuts.

Loosen the lug nuts. 1. Remove the center cap. 2. With the weight of the vehicle on the wheels, loosen the lug nuts. Section 204-01B: Front Suspension 4x4 REMOVAL AND INSTALLATION 1997 F-150, F-250 Workshop Manual Wheel Hub Special Service Tool(s) Bearing Cup Replacer T80T-4000-P Seal Replacer T96T-1175-A Threaded Drawbar

More information

2000 Ranger Workshop Manual

2000 Ranger Workshop Manual SECTION 211-02: Power Steering 2000 Ranger Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/1/1999 Gear Torsion Bar Suspension Special Tool(s) Remover, Tie Rod End 211-001 (TOOL-3290-D)

More information

2001 Chevrolet CORVETTE

2001 Chevrolet CORVETTE riveline Support Assembly Replacement (Automatic Transmission) 1 of 21 10/24/2012 8:58 PM 2001 Chevrolet CORVETTE Submodel: Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Driveline Support Assembly

More information

file://c:\program Files\tsocache\OFFICE_2780\SXN~us~en~file=SXNB2012.htm~gen~ref...

file://c:\program Files\tsocache\OFFICE_2780\SXN~us~en~file=SXNB2012.htm~gen~ref... Page 1 of 14 SECTION 211-02: Power Steering 1999 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 07/27/1998 Gear 5.0L Removal 1. Place the front wheels in the straight

More information

1984 Dodge W250 PICKUP

1984 Dodge W250 PICKUP 1984 Dodge W250 PICKUP Submodel: Engine Type: V8 Liters: 5.2 Fuel Delivery: CARB Fuel: GAS Dana 44 MODELS THROUGH 1984 2. Raise and safely support the vehicle, then remove the wheel hub and bearings as

More information

07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES

07-13 TOYOTA TUNDRA 2WD 6 LIFT SPINDLES MAXTRAC SUSPENSION 4030 E LEAVERTON CT ANAHEIM, CA 92807 714-630-0363 WWW.MAXTRACSUSPENSION.COM SALES@MAXTRACSUSPENSION.COM PRODUCT: K886764 07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES PARTS LIST QTY LIFT

More information

See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( )

See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( ) Page 1 of 9 ARTICLE BEGINNING DESCRIPTION Front suspension uses coil springs with integral shock absorbers. Coil springs are mounted between the upper control arms and vehicle frame. A stabilizer bar controls

More information

This file is available for free download at

This file is available for free download at This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing

More information

Wheel end bearing and seal installation guide. Automotive edition Featuring front and rear wheel drive models

Wheel end bearing and seal installation guide. Automotive edition Featuring front and rear wheel drive models Wheel end bearing and seal installation guide Automotive edition Featuring front and rear wheel drive models Introduction Contents The SKF Seal and Bearing lnstallation Guide (SKF #457809) covers the removal

More information

2005 Mustang Workshop Manual

2005 Mustang Workshop Manual SECTION 205-00: Driveline System General Information 2005 Mustang Workshop Manual GENERAL PROCEDURES Procedure revision date: 07/29/2004 Driveline Angle Inspection Printable View (122 KB) Special Tool(s)

More information

1999 F-150/250 Workshop Manual

1999 F-150/250 Workshop Manual Page 1 of 30 SECTION 205-03: Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 1999 F-150/250 Workshop Manual DISASSEMBLY AND ASSEMBLY Procedure revision date: 01/08/2003 Axle Front Drive Special Tool(s)

More information

DESCRIPTION Acura TSX SUSPENSION Front - TSX. NOTE: For system description and component location, see Fig. 1.

DESCRIPTION Acura TSX SUSPENSION Front - TSX. NOTE: For system description and component location, see Fig. 1. 2004 SUSPENSION Front - TSX DESCRIPTION NOTE: For system description and component location, see Fig. 1. Fig. 1: Identifying Front Suspension Components Wednesday, March 12, 2008 8:30:45 8:30:55 PM Page

More information

Installation Instructions 7 Lift Kit 2015 F150 4WD ONLY( )

Installation Instructions 7 Lift Kit 2015 F150 4WD ONLY( ) IF YOUR ReadyLIFT OFF ROAD SUSPENSION PRODUCT IS MISSING A PART OR HAS A DAMAGED PART, PLEASE CONTACT CUSTOMER SERVICE DIRECTLY. A NEW REPLACEMENT PART WILL BE SENT TO YOU IMMEDIATELY Please read Instructions

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION Page 1 of 6 REMOVAL & INSTALLATION AXLE SHAFTS Removal Raise and support vehicle. Remove front wheels. Remove engine undercovers. Remove cotter pin and lock nut cap. See Fig. 2. Apply brakes and remove

More information

04-08 FORD F150 4 KIT

04-08 FORD F150 4 KIT 9257700 04-08 FORD F50 4 KIT THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. Rough Country recommends a certified technician install this system. In addition to these instructions, professional

More information

SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING

SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically

More information

INSTALLATION INSTRUCTION 88148

INSTALLATION INSTRUCTION 88148 INSTALLATION INSTRUCTION 88148 Rev C For Rancho Suspension Systems RS6548, RS6549 & RS6550: GM 2500HD, 2500, and 1500HD Trucks READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION

More information

INSTALLATION INSTRUCTION 88088

INSTALLATION INSTRUCTION 88088 INSTALLATION INSTRUCTION 88088 For Rancho Suspension Systems RS6588 & RS6589: FORD F-150 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:

More information

TION AND OPERATION Procedure revision date: 01/22/1999

TION AND OPERATION Procedure revision date: 01/22/1999 TION AND OPERATION Procedure revision date: 01/22/1999 Main Components and Functions AX4S Main Components http://www.fordtechservice.dealerconnection.com/pubs/content/~wsww/~mus~len/20/sww71006.htm (1

More information

Installation Instructions

Installation Instructions Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to

More information

2007 Hummer H Driveline/Axle Wheel Drive Shafts - H3. Fastener Tightening Specifications Specification Application

2007 Hummer H Driveline/Axle Wheel Drive Shafts - H3. Fastener Tightening Specifications Specification Application 2007 Driveline/Axle Wheel Drive Shafts - H3 SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Front Wheel Drive Shaft Nut 260

More information

2001 F-650/750 Workshop Manual

2001 F-650/750 Workshop Manual 26. Pack the reverse idler gear bearings with lubricant. Use Moly number 2 lubricant or equivalent. 27. Install the following: 1. Assemble the reverse idler gear and bearings onto the idler shaft. 2. Position

More information

303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine

303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine 2010 MKZ Report a problem with this article 303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid REMOVAL Procedure revision date: 10/19/2012 Engine Special Tool(s) 2,200# Floor Crane,

More information

»Product» Safety Warning

»Product» Safety Warning #F2622 Installation Instructions 1997-2003 Ford F-150 4WD 6" Suspension System Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad

More information

2003 Ford Focus ZTW SUSPENSION Front - Focus

2003 Ford Focus ZTW SUSPENSION Front - Focus HUB/STEERING KNUCKLE ASSEMBLY Removal 1. Loosen the strut tower nuts by at least five turns. See Fig. 4. Loosen the wheel hub retaining nut. Raise and support vehicle. Remove front wheel, brake caliper

More information

Lower Arm ( ) Special Service Tools. Removal.

Lower Arm ( ) Special Service Tools. Removal. Page 1 of 6 (60.35.02) Special Service Tools Ball joint separator 205-754 (LRT-54-027) Halfshaft remover/replacer 204-506/1 (LRT-60-030/1) Halfshaft remover/replacer 204-506/3 (LRT-60-030/3) Retainers

More information

kit contents trail-safe samurai inner axle seal suzuki samurai (all engines) InstalLation Instructions

kit contents trail-safe samurai inner axle seal suzuki samurai (all engines) InstalLation Instructions InstalLation Instructions trail-safe samurai inner axle seal 300748-3-kit 1986-1995 suzuki samurai (all engines) kit contents 5356 PINE AVE FRESNO, CA 93727 USA TOLL FREE: 877.4X4.TOYS WORLDWIDE: 559.252.4950

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 2500 DROPPED FRONT SPINDLE CHEVROLET C / K and G.M.C. SIERRA 1500 / 2500 / 3500 Pick-Ups Congratulations! You were selective enough to choose a BELLTECH PRODUCT. We have spent

More information

Steering Gear Replacement

Steering Gear Replacement Page 1 of 7 Steering Gear Replacement Removal Procedure Notice: With wheels of the vehicle facing straight ahead, secure the steering wheel utilizing steering column anti-rotation pin, steering column

More information

1. Set the position of the hub to FREE and remove the six hex-drive bolts.

1. Set the position of the hub to FREE and remove the six hex-drive bolts. 1. Raise vehicle on a hoist, remove road wheels, disconnect the drag-link from the passenger-side hub assembly and disconnect the steering tie rod ends from both the driver and passenger side hub assemblies.

More information

BRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS

BRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS BRAKE SYSTEM 1988 Toyota Celica 1988-89 BRAKES Toyota Celica, Corolla, MR2, Tercel DESCRIPTION The hydraulic brake system uses a tandem master cylinder with a vacuum power assist servo. MR2 and some Celica

More information

Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles

Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles Rear Suspension Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles All-Wheel Drive (AWD) Vehicles Front Wheel Drive (FWD) Vehicles Removal All vehicles NOTICE: Suspension fasteners are critical

More information

1. General Description

1. General Description General Description 1. General Description A: SPECIFICATION 1. PROPELLER SHAFT Propeller shaft type 3UJ Front propeller shaft Joint-to-joint length: L 1 mm (in) 633 (24.92) Rear propeller shaft Joint-to-Joint

More information

FRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX

FRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX D DRIVELINE/AXLE A SECTION FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Precautions... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION, AND HARSHNESS (NVH)

More information

04-08 FORD F150 6 KIT

04-08 FORD F150 6 KIT 957600 THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. 0-08 FORD F50 6 KIT Rough Country recommends a certified technician install this system. In addition to these instructions, professional

More information

DISASSEMBLY AND ASSEMBLY

DISASSEMBLY AND ASSEMBLY 205-02B-1 DISASSEMBLY AND ASSEMBLY Differential Case and Ring Gear Material Item Specification 205-02B-1 Special Tool(s) Additive Friction Modifier EST-M2C118-A XL-3 2-Jaw Puller 205-D072 (D97L-4221-A)

More information

INSTALLATION INSTRUCTION 88051

INSTALLATION INSTRUCTION 88051 INSTALLATION INSTRUCTION 88051 For Rancho Suspension System RS6551: Chevrolet 2500 Suburban & 2500 Avalanche READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT

More information

*1576BAG9* 1576BAG FORD F KIT C THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS.

*1576BAG9* 1576BAG FORD F KIT C THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. 957600C THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR SUSPENSION NEEDS. 0-08 FORD F50-6 KIT Rough Country recommends a certified technician install this system. In addition to these instructions, professional

More information

Page 1 of 11 1Search FRAME CROSS BAR 2001 Chrysler PT Cruiser 2.4L Eng Base CAUTION: DO NOT attempt to modify any suspension or steering components by heating or bending. Removal [ STABILIZER BAR ] 1.

More information

M-2300-K Cobra Disk Brake Conversion Kit INSTALLATION INSTRUCTIONS

M-2300-K Cobra Disk Brake Conversion Kit INSTALLATION INSTRUCTIONS Please contact the Tech Hot Line for the most current instruction information (586) 468-1356!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! INTRODUCTION: The components in

More information

FRONT AXLE SECTION FAX CONTENTS DRIVELINE/AXLE FAX-1 SERVICE INFORMATION... 2

FRONT AXLE SECTION FAX CONTENTS DRIVELINE/AXLE FAX-1 SERVICE INFORMATION... 2 DRIVELINE/AXLE SECTION FAX A FRONT AXLE B C FAX CONTENTS E SERVICE INFORMATION... 2 PRECAUTIONS... 2 Caution...2 PREPARATION... 3 Special Service Tool...3 Commercial Service Tool...3 NOISE, VIBRATION AND

More information

AXLE SYSTEM PROBLEM SYMPTOMS TABLE AH 1

AXLE SYSTEM PROBLEM SYMPTOMS TABLE AH 1 AXLE AXLE SYSTEM 1 AXLE SYSTEM PROBLEM SYMPTOMS TABLE HINT: Use the table below to help you find the cause of the problem. The numbers indicate the ranked order of probability of each of the possible causes.

More information

1. General Description

1. General Description General Description 1. General Description A: SPECIFICATION 1. PROPELLER SHAFT Model All models Propeller shaft type EDJ Front propeller shaft Joint-to-joint length: L 1 mm (in) AT 735.5 (28.96) MT 675.5

More information

Installation Instructions

Installation Instructions Installation Instructions 6 Suspension System FTS25005BK / FTS25006BK 2006-2012 Nissan Frontier 2wd/4wd SHORT BED ONLY Tool List: (not included) Floor Jack & Jack Stands Assorted Metric & S.A.E Sockets

More information

DRIVE SHAFT & FRONT AXLE

DRIVE SHAFT & FRONT AXLE DRIVE SHAFT & FRONT AXLE Return To Main Table of Contents GENERAL... 2 DRIVE SHAFT... 6 HUB AND KNUCKLE... 13 FRONT AXLE... 15 GENERAL GENERAL SPECIFICATIONS Drive shaft Joint type Outer Inner Length (Joint

More information

Page 1 of 7 Section 07-01A: Transmission, Automatic, E4OD IN-VEHICLE SERVICE 1993 Bronco/Econoline/F-Series Workshop Manual Valve Bodies and Intermediate Band Servo NOTE: If a transmission has been disassembled

More information

1. Set the position of the hub to FREE and remove the six hex-drive bolts.

1. Set the position of the hub to FREE and remove the six hex-drive bolts. 1. Raise vehicle on a hoist, remove road wheels, disconnect the drag-link from the passenger-side hub assembly and disconnect the steering tie rod ends from both the driver and passenger side hub assemblies.

More information

LIMITED SLIP DIFFERENTIAL INSTALLATION

LIMITED SLIP DIFFERENTIAL INSTALLATION Installation of the limited slip gear can be done with axle out of car or with car lifted to gain access from underneath. Refer to repair manual for proper lifting instructions if car is to be lifted.

More information

1 M-3000-H4 F150 4X4 Lowering Kit

1 M-3000-H4 F150 4X4 Lowering Kit READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. IT IS RECOMMENDED THAT INSTALLATION BE DONE BY A QUALIFIED MECHANIC. REPLACE ALL STOCK PARTS THAT ARE DAMAGED OR WORN. ALWAYS WEAR EYE PROTECTION.

More information

FRONT AXLE SECTION FAX CONTENTS D DRIVELINE/AXLE FAX-1 FAX

FRONT AXLE SECTION FAX CONTENTS D DRIVELINE/AXLE FAX-1 FAX D DRIVELINE/AXLE SECTION FAX A FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Precautions... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION, AND HARSHNESS

More information

DISASSEMBLY AND ASSEMBLY

DISASSEMBLY AND ASSEMBLY 205-03-1 Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 205-03-1 DISASSEMBLY AND ASSEMBLY Axle Front Drive Special Tool(s) 2-Jaw Puller 205-D072 (D97L-4221-A) Special Tool(s) Carrier Bearing Replacer

More information

FRONT AXLE SECTION FAX CONTENTS TRANSMISSION & DRIVELINE FAX-1 SYMPTOM DIAGNOSIS... 2 ON-VEHICLE REPAIR... 7 PRECAUTION... 3

FRONT AXLE SECTION FAX CONTENTS TRANSMISSION & DRIVELINE FAX-1 SYMPTOM DIAGNOSIS... 2 ON-VEHICLE REPAIR... 7 PRECAUTION... 3 TRANSMISSION & DRIVELINE SECTION FAX A FRONT AXLE B C FAX CONTENTS E SYMPTOM DIAGNOSIS... 2 NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING... 2 NVH Troubleshooting Chart...2 PRECAUTION... 3 PRECAUTIONS...

More information

This file is available for free download at

This file is available for free download at This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing

More information

FRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX

FRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX D DRIVELINE/AXLE A SECTION FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 Precautions... 2 PREPARATION...

More information

03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions

03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions Hellion Power Systems 03-04 Mach 1 Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation

More information

FRONT AXLE SECTION FAX CONTENTS D DRIVELINE/AXLE FAX-1 FAX

FRONT AXLE SECTION FAX CONTENTS D DRIVELINE/AXLE FAX-1 FAX D DRIVELINE/AXLE SECTION FAX A FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Caution... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION AND HARSHNESS (NVH)

More information

'99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS

'99-03 CHEVROLET/GMC IFS 4WD 6 SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS 1/16/04 '99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N. 10-41099 INSTALLATION INSTRUCTIONS NOTE: Each Lift Kit and options to Lift Kits are packaged separately. Therefore, installation procedures

More information

JOINT SHAFT REMOVAL/INSTALLATION

JOINT SHAFT REMOVAL/INSTALLATION 2001 MPV 2001 - MPV - Workshop Manual - Driveline/Axle JOINT SHAFT REMOVAL/INSTALLATION Report a problem with this article Performing the following procedures without first removing the ABS wheel speed

More information

DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts

DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045

More information

WARNING: Only perform this installation if you are experienced, fully equipped mechanic.

WARNING: Only perform this installation if you are experienced, fully equipped mechanic. DYNATRAC V3.2 2005-Present Ford Super Duty 250/350-4x4, Front Axle, Free Spin Conversion Kit Some of the less common tools, which will be required: 6 point Spanner socket (OTC #7090-A or equivalent). These

More information

1. Remove the parcel tray. For additional information, refer to Section

1. Remove the parcel tray. For additional information, refer to Section SECTION 204-02: Rear Suspension 2001 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/19/2003 Strut and Spring Assembly Four Door Removal CAUTION: Suspension fasteners

More information

TOYOTA FJ CRUISER 6 SUSPENSION KIT

TOYOTA FJ CRUISER 6 SUSPENSION KIT 92177000 TOYOTA FJ CRUISER 6 SUSPENSION KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these instructions,

More information

FRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX

FRONT AXLE SECTION CONTENTS D DRIVELINE/AXLE FAX-1 FAX D DRIVELINE/AXLE A SECTION FRONT AXLE B C FAX CONTENTS E PRECAUTIONS... 2 Precautions... 2 PREPARATION... 3 Special Service Tools... 3 Commercial Service Tools... 3 NOISE, VIBRATION, AND HARSHNESS (NVH)

More information

Superlift 4 lift system for 2002 and newer FORD EXPLORER SPORT TRAC 4WD with torsion bar front suspension INSTALLATION INSTRUCTIONS

Superlift 4 lift system for 2002 and newer FORD EXPLORER SPORT TRAC 4WD with torsion bar front suspension INSTALLATION INSTRUCTIONS INTRODUCTION Superlift 4 lift system for 2002 and newer FORD EXPLORER SPORT TRAC 4WD with torsion bar front suspension INSTALLATION INSTRUCTIONS Installation requires a professional mechanic. Prior to

More information

INSTALLATION INSTRUCTION 88094

INSTALLATION INSTRUCTION 88094 INSTALLATION INSTRUCTION 88094 FOR RANCHO SUSPENSION SYSTEM RS6594B 4WD & 2WD NISSAN TITAN READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev D IMPORTANT NOTES! WARNING:

More information

M-2300-M Mustang GT Rear Disc Brake Bracket Kit INSTALLATION INSTRUCTIONS

M-2300-M Mustang GT Rear Disc Brake Bracket Kit INSTALLATION INSTRUCTIONS Please contact the Tech Line for the most current instruction information (800) 367-3788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! INTRODUCTION: This kit allows for the

More information

PRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Ford F150 4WD 4" Suspension Lift Kit

PRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Ford F150 4WD 4 Suspension Lift Kit 2015 Ford F150 4WD 4" Suspension Lift Kit PRE-INSTALLATION 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front Brake Line

More information

2004 DRIVELINE/AXLE. Rear Drive Axle - Corvette. Fastener Tightening Specifications Specification Application

2004 DRIVELINE/AXLE. Rear Drive Axle - Corvette. Fastener Tightening Specifications Specification Application 2004 DRIVELINE/AXLE Rear Drive Axle - Corvette SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Differential Case Bolts 55 N.m

More information

1995 Aerostar/Ranger/Explorer

1995 Aerostar/Ranger/Explorer Page 1 of 13 Section 03-01C: Engine, 4.0L V-6 DISASSEMBLY AND ASSEMBLY 1995 Aerostar/Ranger/Explorer Workshop Manual Engine Disassembly 1. NOTE: Before starting disassembly, remove all wiring harnesses,

More information