Size: px
Start display at page:

Download ""

Transcription

1 Page 1 of 6 Section 07-01A: Transaxle, Automatic CD4E 1996 Probe Workshop Manual REMOVAL Procedure revision date: 06/14/2000 Transaxle Item Part Number Description Battery Battery Tray 3 Wheel and Tire Assembly LH Engine Support Insulator Lower Transaxle Support Insulator 6 6A023 Transmission Support Crossmember Transaxle 8 7A228 Oil Filler Tube Rear Transaxle Support Insulator 10 6E042 Rear Transaxle Support Bracket Front Transaxle Support Insulator 12 Front Transaxle Support Bracket 13 5K484 Stabilizer Bar Link 14 Torque Converter Nut 15 3A329 Halfshaft Crossmember 17 3B436 Front Wheel Driveshaft and Joint 18 3B437 Front Wheel Driveshaft and Joint Starter Motor 20 7E395 Shift Cable and Bracket 21 Fuel Filter Bracket Mounting Nut 22 9J444 Intake Manifold Support 1. Disconnect the battery cables. 2. Remove the battery hold-down and battery (10655) from the vehicle. 3. Remove the three battery tray bolts and the battery tray (10732). 4. Remove the air cleaner assembly. Refer to Section 03-12A for the removal procedure.

2 Page 2 of 6 5. Disconnect the transmission range (TR) sensor electrical connector. 6. Remove the two TR sensor bolts. Remove the TR sensor. 7. Remove the two ground wire bracket bolts. 8. Remove the shift cable from the cable bracket. 9. Remove the two shift cable bracket bolts. Remove the cable bracket. 10. CAUTION: Do not pull on the connector wires or use a hammer on the connector. Disconnect the CD4E transaxle electrical connector by pushing on the retaining ring and pulling up gently on the connector. 11. Disconnect and plug the oil cooler outlet and inlet hoses.

3 Page 3 of Remove the two upper starter motor bolts. 13. Support the engine with Three Bar Engine Support or equivalent. 14. Remove the top three transaxle-to-engine bolts. 15. Remove the two fuel filter bracket nuts. 16. Remove the two ignition coil nuts and position the ignition coil out of the way. 17. Remove the three speed control servo nuts and position the speed control servo out of the way. 18. Remove the three ignition coil mounting strap bolts. 19. Disconnect the wire harness clips from the ignition coil mounting straps. Remove the ignition coil mounting straps. 20. Remove the two nuts and two bolts from the LH engine support insulator. 21. Remove the LH engine support insulator through bolt. Remove the LH engine support insulator. 22. Raise and support the vehicle.

4 Page 4 of Remove the front wheels. 24. Remove both front fender splash shields (16103). 25. Remove the six crossmember bolts. 26. Remove the crossmember. 27. Remove the six rear engine support nuts and two bolts. 28. Remove the transmission support crossmember (6A023). 29. Remove the front wheel driveshaft and joints (3B436). Refer to Section for the removal procedure. 30. Remove the intake manifold support bolts. 31. Remove the intake manifold support (9J444). 32. Disconnect the S-terminal wire. 33. Remove the B-terminal wire nut and disconnect the B-terminal wire. 34. Remove the lower starter motor bolt. 35. Remove the starter motor (11001). 36. Disconnect the Transmission Speed Sensor (TSS) connector. 37. Remove the four torque converter-to-flywheel nuts through the starter pocket.

5 Page 5 of Remove the front transaxle support insulator through bolt. Remove the front transaxle support insulator. 39. Remove the four front transaxle support bracket bolts. Remove the front transaxle support bracket. 40. Remove the rear transaxle support insulator through bolt. 41. Lower the vehicle. 42. Lower the transaxle by loosening the bolt on the Three Bar Engine Support Raise and support the vehicle. 44. NOTE: If using Rotunda Hi-Lift Jack , also use Transmission Jack Adapter If using the Rotunda Hi-Lift Jack 164-R3508, it does not require an adapter. Secure the transaxle to a suitable jack, using the appropriate adapter. 45. Remove the three engine-to-transaxle bolts. 46. Remove the two remaining transaxle-to-engine bolts. 47. Use a screwdriver or a suitable tool to separate the transaxle from the engine (6007). 48. Partially lower the transaxle from the engine. 49. Disconnect the Vehicle Speed Sensor (VSS) connector. 50. Lower the transaxle from the vehicle.

6 Page 6 of 6

2002 F-150 Workshop Manual

2002 F-150 Workshop Manual Page 1 of 8 SECTION 307-01B: Automatic Transmission 4R70W 2002 F-150 Workshop Manual REMOVAL Procedure revision date: 04/02/2003 Transmission Special Tool(s) Retainer, Torque Converter 307-346 (T97T-7902-A)

More information

2004 Lincoln LS Workshop Manual

2004 Lincoln LS Workshop Manual SECTION 310-00: Fuel System 2004 Lincoln LS Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/23/2004 Fuel Tank and Filler Pipe Printable View (541 KB) Special Tool(s) Fuel Drain Hose

More information

303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine

303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine 2010 MKZ Report a problem with this article 303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid REMOVAL Procedure revision date: 10/19/2012 Engine Special Tool(s) 2,200# Floor Crane,

More information

1998 Ford EXPEDITION. Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS. Transmission

1998 Ford EXPEDITION. Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS. Transmission 1998 Ford EXPEDITION Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS SECTION 307-01C: Automatic Transmission 4R100 1998 Expedition/Navigator Workshop Manual REMOVAL Procedure revision

More information

1. Remove the battery tray. For additional information, refer to Battery Tray ( )

1. Remove the battery tray. For additional information, refer to Battery Tray ( ) Page 1 of 11 Removal 1. Remove the battery tray. For additional information, refer to Battery Tray (86.15.11) 2. Remove the air cleaner. For additional information, refer to Air Cleaner (19.10.05) 3. NOTE

More information

ENGINE ASSEMBLY. COMPONENTS (Part 1)

ENGINE ASSEMBLY. COMPONENTS (Part 1) 1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS

More information

Oil Pan Replacement Buick Regal

Oil Pan Replacement Buick Regal 2000 Buick Regal Oil Pan Replacement Removal Procedure Tools Required J 28467-90A Engine Support Adapters J 28467-B Universal Engine Support Fixture J 36462-A Engine Support Adapter Leg Set 1. Disconnect

More information

DESCRIPTION AND OPERATION

DESCRIPTION AND OPERATION 303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589

More information

file://c:\program Files\tsocache\OFFICE_5164\SYA~us~en~file=SYA1C003.htm~gen~re...

file://c:\program Files\tsocache\OFFICE_5164\SYA~us~en~file=SYA1C003.htm~gen~re... Page 1 of 26 SECTION 501-12: Instrument Panel and Console 2000 Crown Victoria/Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/21/1999 Instrument Panel Removal CAUTION:

More information

1 of 12 10/5/2015 8:11 AM

1 of 12 10/5/2015 8:11 AM 1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant

More information

2001 Chevrolet CORVETTE

2001 Chevrolet CORVETTE riveline Support Assembly Replacement (Automatic Transmission) 1 of 21 10/24/2012 8:58 PM 2001 Chevrolet CORVETTE Submodel: Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Driveline Support Assembly

More information

file://c:\program Files\tsocache\OFFICE_2780\SXN~us~en~file=SXNB2012.htm~gen~ref...

file://c:\program Files\tsocache\OFFICE_2780\SXN~us~en~file=SXNB2012.htm~gen~ref... Page 1 of 14 SECTION 211-02: Power Steering 1999 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 07/27/1998 Gear 5.0L Removal 1. Place the front wheels in the straight

More information

MAIN CONTROL VALVE BODY. Removal 1. Disconnect the battery cables. 2. Remove the battery and tray.

MAIN CONTROL VALVE BODY. Removal 1. Disconnect the battery cables. 2. Remove the battery and tray. 1 of 17 MAIN CONTROL VALVE BODY Removal 1. Disconnect the battery cables. 2. Remove the battery and tray. 3. Disconnect the breather tube and mass air flow (MAF) / intake air temperature (IAT) sensor.

More information

Disconnect the breather tube and mass air flow (MAF) /intake air temperature (IAT) sensor.

Disconnect the breather tube and mass air flow (MAF) /intake air temperature (IAT) sensor. 1 of 19 10/1/2011 11:11 AM oval 1. 2. Disconnect the battery cables. Remove the battery and tray. 3. Disconnect the breather tube and mass air flow (MAF) /intake air temperature (IAT) sensor. 4. Remove

More information

SECTION Automatic Transaxle/Transmission 4R70E/4R75E

SECTION Automatic Transaxle/Transmission 4R70E/4R75E 307-01-i Automatic Transaxle/Transmission 4R70E/4R75E 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 4R70E/4R75E CONTENTS PAGE Transmission Four Wheel Drive (4WD)... 307-01-2 307-01-2 Automatic

More information

Page 1 of 8 Section 03-01: Engine, 4.6L IN-VEHICLE SERVICE 1994 Town Car/Crown Victoria/Grand Marquis Workshop Manual Oil Pan and Oil Pump Screen Cover and Tube Town Car Removal 1. Disconnect battery ground

More information

1. Remove the parcel tray. For additional information, refer to Section

1. Remove the parcel tray. For additional information, refer to Section SECTION 204-02: Rear Suspension 2001 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/19/2003 Strut and Spring Assembly Four Door Removal CAUTION: Suspension fasteners

More information

Page 1 of 7 Section 07-01: Transaxle, Automatic FLC REMOVAL AND INSTALLATION 1992 Tempo/Topaz Workshop Manual Differential In Vehicle Removal Before beginning the Removal procedure, perform the following

More information

REPLACEMENT. 9. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 (a) Remove the 2 bolts and control cable bracket No.1.

REPLACEMENT. 9. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 (a) Remove the 2 bolts and control cable bracket No.1. AUTOMATIC TRANSMISSION / TRANS REPLACEMENT 1. REMOVE HOOD SUBASSY 2. REMOVE BATTERY 3. REMOVE WINDSHIELD WIPER LINK ASSY (See page 666) 4. REMOVE FRONT PANEL ASSY (See page 2610) 5. REMOVE CYLINDER HEAD

More information

1999 E-Series Workshop Manual

1999 E-Series Workshop Manual http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998

More information

1998 Contour/Mystique Workshop Manual

1998 Contour/Mystique Workshop Manual SECTION 30-01: Automatic Transmission/Transaxle 1998 Contour/Mystique Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 09/14/2001 Main Controls Special Tool(s) Aligner, Selector Shaft 30-S290

More information

1999 Explorer/Mountaineer Workshop Manual

1999 Explorer/Mountaineer Workshop Manual Page 1 of 5 SECTION 307-01B: Automatic Transmission 5R55E 1999 Explorer/Mountaineer Workshop Manual REMOVAL Procedure revision date: 07/27/1998 Transmission Special Tool(s) Torque Converter Holding Tool

More information

ENGINE ASSEMBLY COMPONENTS EM 170 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY V-BANK COVER VACUUM HOSE AIR CLEANER ASSEMBLY NO. 2 VENTILATION HOSE

ENGINE ASSEMBLY COMPONENTS EM 170 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY V-BANK COVER VACUUM HOSE AIR CLEANER ASSEMBLY NO. 2 VENTILATION HOSE 170 ENGINE 1GR-FE MECHANICAL COMPONENTS 1GR-FE ENGINE MECHANICAL ENGINE 7.5 (76, 66 in.*lbf) V-BANK COVER 8.0 (82, 71 in.*lbf) 8.0 (82, 71 in.*lbf) VACUUM HOSE AIR CLEANER NO. 2 VENTILATION HOSE MASS AIR

More information

Disconnect negative battery cable and remove coolant bottle cap.

Disconnect negative battery cable and remove coolant bottle cap. 1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use

More information

PARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque

PARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque ENGINE MECHANICAL 1417 COMPONENTS 141FP01 Radiator Grille Front Bumper Cover Engine Under Cover RH Engine Under Cover LH A79361 962 1418 ENGINE MECHANICAL Heater Outlet Water Hose 7.0 (71, 62 in. lbf)

More information

Transmission Diesel Engines

Transmission Diesel Engines Page 1 of 17 SECTION 307-01B: Automatic Transaxle/Transmission TorqShift 6 2011 F-250, 350, 450, 550 Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 11/12/2010 Transmission

More information

Timing Drive Components Camshaft Timing

Timing Drive Components Camshaft Timing SECTION 303-01B: Engine 4.0L SOHC 1998 Explorer/Mountaineer Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/17/2002 Timing Drive Components Camshaft Timing Special Tool(s) Timing Chain Tensioner

More information

Automatic Transmission Assembly Remove and Install (2,9 V6 24V engine) ( ) Remove

Automatic Transmission Assembly Remove and Install (2,9 V6 24V engine) ( ) Remove Automatic Transmission Assembly Remove and Install (,9 V6 4V engine) (7 4 0) Special Tools -40 Engine support bar -40-0 Adaptor for -40-40-03 Adaptor for -40 Workshop Equipment Transmission jack Materials

More information

2013 Kia Optima L4-2.0L Turbo

2013 Kia Optima L4-2.0L Turbo 1 of 13 5/29/2016 11:34 AM 2013 Kia Optima L4-2.0L Turbo Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement Removal CAUTION: Use fender covers to avoid damaging painted

More information

1 M-3000-H4 F150 4X4 Lowering Kit

1 M-3000-H4 F150 4X4 Lowering Kit READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. IT IS RECOMMENDED THAT INSTALLATION BE DONE BY A QUALIFIED MECHANIC. REPLACE ALL STOCK PARTS THAT ARE DAMAGED OR WORN. ALWAYS WEAR EYE PROTECTION.

More information

INTAKE (INDUCTION) IN(TURBO)

INTAKE (INDUCTION) IN(TURBO) IN(TURBO) Page 1. General Description...2 2. Air Cleaner...7 3. Air Intake Duct...8 4. Intake Duct...9 5. Intercooler...10 6. Turbocharger...12 7. Air By-pass Valve...14 8. Resonator Chamber...15 GENERAL

More information

PARTIAL ENGINE ASSY (2TR FE)

PARTIAL ENGINE ASSY (2TR FE) COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER

More information

1994 Bronco/Econoline/F-Series

1994 Bronco/Econoline/F-Series Page 1 of 8 Section 10-01A: Fuel Tank, Filters, Lines and Electric Fuel Pump, Gasoline Engines REMOVAL AND INSTALLATION 1994 Bronco/Econoline/F-Series Workshop Manual Fuel Tank Steel Midship Fuel Tank,

More information

2001 Ranger Workshop Manual. 1. Drain the cooling system. For additional information, refer to Section

2001 Ranger Workshop Manual. 1. Drain the cooling system. For additional information, refer to Section Exhaust Gas Recirculation (EGR) Valve 2.3L 1. Drain the cooling system. For additional information, refer to Section 303-03. 2. Disconnect the battery ground cable. For additional information, refer to

More information

2000 Ranger Workshop Manual

2000 Ranger Workshop Manual SECTION 211-02: Power Steering 2000 Ranger Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/1/1999 Gear Torsion Bar Suspension Special Tool(s) Remover, Tie Rod End 211-001 (TOOL-3290-D)

More information

2003 F-Super Duty /Excursion Workshop Manual

2003 F-Super Duty /Excursion Workshop Manual Page 1 of 7 SECTION 303-04F: Fuel Charging and Controls Turbocharger, 6.0L Diesel 2003 F-Super Duty 250-550/Excursion Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Turbocharger

More information

PARTIAL ENGINE ASSY (2ZZ GE)

PARTIAL ENGINE ASSY (2ZZ GE) COMPONENTS 14189 140R701 7.0 (71, 62 in. lbf) Cylinder Head Cover No. 2 19 (194, 14) Radiator Support Upper 19 (194, 14) Radiator Hose Inlet Cruise Control Actuator Assy 6.0 (61, 53 in. lbf) Radiator Assy

More information

3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter

3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter 1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower

More information

FUEL SENDER ASSEMBLY REPLACEM... FUEL TANK REPLACEMENT (CAB/CHASSIS FRONT) (ENGINE CONTROLS 4.8L, 5.3L, AND 6.0L) Document ID#

FUEL SENDER ASSEMBLY REPLACEM... FUEL TANK REPLACEMENT (CAB/CHASSIS FRONT) (ENGINE CONTROLS 4.8L, 5.3L, AND 6.0L) Document ID# FUEL SENDER ASSEMBLY REPLACEM... FUEL TANK REPLACEMENT (CAB/CHASSIS FRONT) (ENGINE CONTROLS 4.8L, 5.3L, AND 6.0L) Document ID# 824435 Fuel Tank Replacement (Cab/Chassis Front) Removal Procedure http://dh.identifix.com/searchfixes/index?roid=158586813&vid=2018330&vsm=4&hasbookmark=0&locationid=2#kw=fuel+pump&soption=1&vetid=8&stmode=1&paging=&smode=2&position=assetcat_9

More information

1992 Clutch. Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT

1992 Clutch. Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT Article Text ARTICLE BEGINNING 1992 Clutch Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT DESCRIPTION All clutches are single disc type. Pressure plate assembly uses a diaphragm spring to engage

More information

2013 Mustang Workshop Manual

2013 Mustang Workshop Manual 32. Attach the wiring harness retainers to the LH side of the oil pan and the front oil pan stud bolts and install the 2 nuts. Tighten to 8 Nm (71 lb-in). 33. Position the underbody shield and install

More information

Caution: This document contains mixed page sizes (8.5 x 11 or 11 x 17), which may affect printing. Please adjust your printer settings according to

Caution: This document contains mixed page sizes (8.5 x 11 or 11 x 17), which may affect printing. Please adjust your printer settings according to Caution: This document contains mixed page sizes (8.5 x 11 or 11 x 17), which may affect printing. Please adjust your printer settings according to the size of each page you wish to print. Parts Catalog

More information

MODEL: 400 Hydrostatic Tractor

MODEL: 400 Hydrostatic Tractor John Deere MODEL: 400 Hydrostatic Tractor THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF JOHN DEERE OR IT'S SUCCESSORS. JOHN DEERE AND IT'S SUCCESSORS ARE NOT RESPONSIBLE FOR THE

More information

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting

More information

05 15A MANUAL TRANSAXLE [F25M-R]

05 15A MANUAL TRANSAXLE [F25M-R] 05 15A MANUAL TRANSAXLE [F25M-R] MANUAL TRANSAXLE [F25M-R] LOCATION INDEX................ 05 15A 1 TRANSAXLE OIL INSPECTION [F25M-R]............. 05 15A 2 TRANSAXLE OIL REPLACEMENT [F25M-R].......... 05

More information

9. Engine Assembly ENGINE ASSEMBLY

9. Engine Assembly ENGINE ASSEMBLY 9. Engine Assembly A: REMOVAL 1) Set the vehicle on a lift. 2) Open the front hood fully, and then support with the hood stay. 3) Collect the refrigerant from A/C system. 4) Release the fuel pressure.

More information

Halfshaft SPECIAL SERVICE TOOL(S) REQUIRED

Halfshaft SPECIAL SERVICE TOOL(S) REQUIRED Page 1 of 8 Section 05-04: Halfshaft, Front Wheel 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Halfshaft SPECIAL SERVICE TOOL(S) REQUIRED Description Tool

More information

2004 F-150 Workshop Manual

2004 F-150 Workshop Manual Page 1 of 8 SECTION 303-01B: Engine 5.4L (3V) 2004 F-150 Workshop Manual REMOVAL Procedure revision date: 02/10/2004 Engine Printable View (943 KB) Special Tool(s) Modular Engine Lift Bracket 303-F047

More information

CERTAIN 2018 MODEL YEAR EXPEDITION AND NAVIGATOR VEHICLES EQUIPPED WITH R-1234YF REFRIGERANT - SPECIAL R-1234YF REFRIGERANT SERVICE INFORMATION

CERTAIN 2018 MODEL YEAR EXPEDITION AND NAVIGATOR VEHICLES EQUIPPED WITH R-1234YF REFRIGERANT - SPECIAL R-1234YF REFRIGERANT SERVICE INFORMATION PAGE 1 OF 33 CERTAIN 2018 MODEL YEAR EXPEDITION AND NAVIGATOR VEHICLES EQUIPPED WITH R-1234YF REFRIGERANT - SPECIAL R-1234YF REFRIGERANT SERVICE INFORMATION OVERVIEW This program provides special service

More information

CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT

CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT REPLACEMENT N0. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE ). REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE ). REMOVE STARTER ASSY (SEE PAGE 99). REMOVE AUTOMATIC TRANSAXLE ASSY (SEE PAGE

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Powertrain Management» Fuel Delivery and Air Induction» Fuel Tank» Service and Repair» Procedures» Fuel Tank Removal and Installation REMOVAL WARNING: DO NOT SMOKE OR CARRY LIGHTED TOBACCO OR

More information

Fastener Tightening Specifications Specification

Fastener Tightening Specifications Specification 2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt

More information

REMOVAL. 10. REMOVE FRONT SUSPENSION MEMBER BRACE Remove the 8 bolts and brace.

REMOVAL. 10. REMOVE FRONT SUSPENSION MEMBER BRACE Remove the 8 bolts and brace. EM64 ENGINE MECHANICAL (2JZGE) EM1S801 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DRAIN ENGINE OIL 4. REMOVE ENGINE COVER Remove the 4 nuts and engine cover. 5. REMOVE AIR CLEANER

More information

Transmission. Special Tool(s) Installation. All vehicles

Transmission. Special Tool(s) Installation. All vehicles Transmission Special Tool(s) Installation All vehicles 1. CAUTION: Prior to the installation of the transmission, the fluid, cooler lines and the cooler bypass valve must be cleaned. Transmission failure

More information

1 of 14 11/19/ :45 AM

1 of 14 11/19/ :45 AM 1 of 14 11/19/2016 11:45 AM 6F35 Digital Transmission Range (TR) Sensor Removal All vehicles 1. With the vehicle in NEUTRAL, position it on a hoist. 3.0L engine 2. Remove the Air Cleaner (ACL) outlet pipe.

More information

ASSEMBLY/INSTALLATION INSTRUCTIONS

ASSEMBLY/INSTALLATION INSTRUCTIONS ASSEMBLY/INSTALLATION INSTRUCTIONS AURORA 3000 & 4000 SCORPION TURBO SYSTEM NOTICE: The engine oil must be changed any time the turbocharger is removed from the engine. The passages in the block underneath

More information

FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY

FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY Removal and Installation REMOVAL WARNING: Follow the "General Precautions" before working on the fuel system. Refer to "General Precautions".

More information

1 of 8 12/12/2012 6:08 PM 1999 Chevrolet Express - 2WD Express, Savana VIN G Service Manual Engine Engine Mechanical - 6.5L Repair Instructions Engine Replacement Removal Procedure Tools Required J 36857

More information

10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L

10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L 2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN

More information

2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI - Removal and Installation

2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI - Removal and Installation Page 1 of 8 Removal and Installation REMOVAL 1. REMOVE HOOD Torque: 13 Nm (130 kgf-cm, 9 ft. lbs.) 2. REMOVE BATTERY 3. REMOVE ECM AND ECM CASE Torque: 6.9 Nm (70 kgf-cm, 61 inch lbs.) 4. REMOVE ECM BRACKET

More information

Engine Removal/Installation

Engine Removal/Installation Engine Removal/Installation Make sure jacks and safety stands are placed properly and hoist brackets are attached to correct positions on the engine. (See Section 1). Apply parking brake and block rear

More information

Page 1 of 7 Bumpers - Front Bumper Cover Removal and Installation Removal 1. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and

More information

Page 1 of 7 Section 07-01A: Transmission, Automatic, E4OD IN-VEHICLE SERVICE 1993 Bronco/Econoline/F-Series Workshop Manual Valve Bodies and Intermediate Band Servo NOTE: If a transmission has been disassembled

More information

Cylinder head, removing and

Cylinder head, removing and Page 1 of 35 15-2 Cylinder head, removing and installing Note: Replace cylinder head bolts. Always replace self-locking nuts, bolts as well as gaskets and O-rings. After installing a replacement cylinder

More information

22-1 GROUP 22 MANUAL TRANSAXLE CONTENTS MANUAL TRANSAXLE... 22A MANUAL TRANSAXLE OVERHAUL... 22B

22-1 GROUP 22 MANUAL TRANSAXLE CONTENTS MANUAL TRANSAXLE... 22A MANUAL TRANSAXLE OVERHAUL... 22B 22-1 GROUP 22 MANUAL TRANSAXLE CONTENTS............................... 22A OVERHAUL..................... 22B 22A-2 GROUP 22A MANUAL TRANSAXLE CONTENTS GENERAL DESCRIPTION......... 22A-3 DIAGNOSIS 22A-6

More information

IN-VEHICLE REPAIR. Upper Intake Manifold

IN-VEHICLE REPAIR. Upper Intake Manifold 303-01-1 Engine 3.9L and 4.2L 303-01-1 IN-VEHICLE REPAIR Upper Intake Manifold Special Tool(s) Remover, Spark Plug Wire 303-106 (T74P-6666-A) Material Item Silicone Brake Caliper Grease and Dielectric

More information

GM 4T65E Installation Tips

GM 4T65E Installation Tips GM 4T65E Installation Tips WARNING: DO NOT operate vehicle without installing a new transmission oil cooler. We recommend installing a Hayden 1403 or 1404. Bypass the radiator and install the new cooler.

More information

10/13/2016 5:33 PM. Radiator (B205L/R, B235R) To remove

10/13/2016 5:33 PM. Radiator (B205L/R, B235R) To remove 1 of 15 Radiator (B205L/R, B235R) To remove 1. Disconnect the vent hose from the battery. Disconnect the positive and negative battery cables and remove the battery. Note the radio code where applicable.

More information

Page 1 of 10 43: Transmission, automatic, B5254T2, AW50/51 AWD V70 XC (01-) / XC70 (-07), 2004, B5254T2, AW50/51 AWD, L.H.D, YV1SZ59H241147306, 147306 15/10/2011 PRINT 43: Transmission, automatic, B5254T2,

More information

Timing Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar

Timing Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar Timing Chain Renew ( 34 0) Special Tools 40 400 40 Engine support bar 40 0 Adaptor for -40 40 03 Adaptor for -40 Proprietary Tools Scraper Workshop Equipment Transmission jack Materials Cable ties Sealer

More information

2003 Escape Workshop Manual

2003 Escape Workshop Manual Page 1 of 6 SECTION 211-02: Power Steering 2003 Escape Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/06/2005 Steering Gear Printable View (633 KB) Special Tool(s) Tie-Rod End Remover

More information

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie

More information

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION

More information

STARTER COMPONENTS FOR REMOVAL AND INSTALLATION

STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Removal STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Starter Components For Removal And Installation REMOVAL OF STARTER 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started

More information

2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...

2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin... Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine

More information

25. REMOVE OIL PIPE NO.1 (a) Remove the 2 oil pipe unions, and oil pipe No.1. (b) Remove the oil control valve filter LH and gaskets.

25. REMOVE OIL PIPE NO.1 (a) Remove the 2 oil pipe unions, and oil pipe No.1. (b) Remove the oil control valve filter LH and gaskets. CAMSHAFT (RH BANK) (2GRFE) REPLACEMENT 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE 1421) 2. REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE 1421) 4. REMOVE STARTER ASSY (SEE PAGE 199). REMOVE

More information

Timing Chain - Renew ( )

Timing Chain - Renew ( ) «Scorpio '95 Table of Contents» «Section 21: Engine» «Subsection 21-05: 2,9 V6 24V Cosworth Engine» «REMOVAL AND INSTALLATION» Timing Chain - Renew (21 314 0) Special Tools 21-140-01Adaptor for 21-140

More information

REMOVAL AND INSTALLATION OF TRANSAXLE (4WD)

REMOVAL AND INSTALLATION OF TRANSAXLE (4WD) MT63 REMOVAL AND INSTALLATION OF TRANSAXLE (4WD) REMOVAL AND INSTALLATION OF TRANSAXLE REMOVE AND INSTALL TRANSAXLE AS SHOWN MT64 REMOVAL OF TRANSAXLE 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY

More information

IN-VEHICLE REPAIR. Output Shaft Speed (OSS) Sensor. Removal

IN-VEHICLE REPAIR. Output Shaft Speed (OSS) Sensor. Removal 307-01-1 Automatic Transaxle/Transmission 6F50 307-01-1 IN-VEHICLE REPAIR Output Shaft Speed (OSS) Sensor Material Item MERCON V Automatic Transmission Fluid XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada)

More information

COMPONENT LOCATOR > DISASSEMBLED VIEWS

COMPONENT LOCATOR > DISASSEMBLED VIEWS Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine

More information

CLUTCH Toyota Celica DESCRIPTION ADJUSTMENTS CLUTCH PEDAL HEIGHT Clutch. Celica

CLUTCH Toyota Celica DESCRIPTION ADJUSTMENTS CLUTCH PEDAL HEIGHT Clutch. Celica CLUTCH 1993 Toyota Celica 1993 Clutch Celica DESCRIPTION The single, dry disc type clutch uses a hydraulically operated master cylinder and a release cylinder mounted on clutch housing. Clutch release

More information

The following tools will be required to perform this new service procedure outlined in this bulletin:

The following tools will be required to perform this new service procedure outlined in this bulletin: The following new service information outlined in this bulletin will aid technicians in removal and installation of the cylinder head without the removal of the front engine cover. The new service procedure

More information

3/15/2015 1:10 PM TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC]

3/15/2015 1:10 PM TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1 of 17 TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1. Disconnect the negative battery cable. 2. Remove the under cover. 3. Remove the front wheels and tires (RH). 4. Remove the splash shield. 5. Remove

More information

1999 Villager Workshop Manual

1999 Villager Workshop Manual Page 1 of 5 SECTION 303-03: Engine Cooling 1999 Villager Workshop Manual GENERAL PROCEDURES Procedure revision date: 07/27/1998 Cooling System Draining, Filling And Bleeding Draining WARNING: Do not open

More information

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat

More information

REMOVAL. Fig Sized for Print

REMOVAL. Fig Sized for Print ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting

More information

Code 0 Description Pic Link # Used Diameter Thread Pitch Length Washer 1 Washer2 Nut size Class Notes F Alternator bracket mounting bolts

Code 0 Description Pic Link # Used Diameter Thread Pitch Length Washer 1 Washer2 Nut size Class Notes F Alternator bracket mounting bolts Code 0 Description Pic Link # Used Diameter Thread Pitch Length Washer 1 Washer2 Nut size Class Notes 1 15 1 2F Alternator bracket mounting bolts (Engine Lift Hook) 3 10 1.25 30 split washer flat 4 14mm

More information

1999 F-150/250 Workshop Manual

1999 F-150/250 Workshop Manual Page 1 of 8 SECTION 303-01B: Engine 4.6L and 5.4L IN-VEHICLE REPAIR Procedure revision date: 02/03/1999 Intake Manifold Lightning Removal WARNING: Do not smoke or carry lighted tobacco or open flame of

More information

Illustrated Parts List. Model Series AIR COOLED

Illustrated Parts List. Model Series AIR COOLED FORM MS6154--06/10/2010 REPLACE FORM MS6154--03/06/2010 FILE IN SECT. 2 OF SERVICE MANUAL Illustrated Parts List Model Series AIR COOLED TYPE NUMBERS 0035, 0038, 0048, 0076, 0078, 0079, 0100, 0111, 0113,

More information

Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles

Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles Rear Suspension Wheel Bearing and Wheel Hub All-Wheel Drive (AWD) Vehicles All-Wheel Drive (AWD) Vehicles Front Wheel Drive (FWD) Vehicles Removal All vehicles NOTICE: Suspension fasteners are critical

More information

Engine and A4LDE Automatic Transmission Remove and Install ( ) Remove

Engine and A4LDE Automatic Transmission Remove and Install ( ) Remove Engine and A4LDE Automatic Transmission Remove and Install ( 3 0) Special Tools 068A -068A Engine lifting bracket -540 Bolt tightening angle gauge Workshop Equipment Transmission jack Workshop crane Assembly

More information

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly. ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.

More information

Mazda North American Operations Irvine, CA

Mazda North American Operations Irvine, CA Service Bulletin Mazda North American Operations Irvine, CA 92618-2922 Subject: MIL ON - P2070 SET Bulletin No: 01-019/08 2004-2007 RX-8 - MIL ON - P2070 SET BULLETIN NOTE This bulletin supersedes the

More information

Page 1 of 11 43: Transmission, automatic, B5244T3, AW55-50/51SN V70 (00-08), 2003, B5244T3, AW55-50/51SN, L.H.D, YV1SW58D132320765, 320765 29/3/2014 PRINT 43: Transmission, automatic, B5244T3, AW55-50/51SN

More information

Mazda3 - Workshop Manual - Engine

Mazda3 - Workshop Manual - Engine Page 1 of 18 2005 - Mazda3 - Workshop Manual - Engine TIMING CHAIN REMOVAL/INSTALLATION WARNING: Fuel vapor is hazardous. It can very easily ignite, causing serious injury and damage. Always keep sparks

More information

ENGINE SPECIFICATIONS

ENGINE SPECIFICATIONS ENGINE SPECIFICATIONS MECHANICAL LOCATION INDEX Engine cover 1 (See ENGINE COVER REMOVAL/INSTALLATION.) 2 Drive belt Page 1 (See DRIVE BELT DEFLECTION/TENSION INSPECTION.) (See DRIVE BELT ADJUSTMENT.)

More information

OVERVIEW: KIT INCLUDES:

OVERVIEW: KIT INCLUDES: Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

2002 Crown Victoria/Grand Marquis Workshop Manual

2002 Crown Victoria/Grand Marquis Workshop Manual Page 1 of 24 SECTION 303-01: Engine 2002 Crown Victoria/Grand Marquis Workshop Manual INSTALLATION Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Installer, Crankshaft Vibration Damper

More information

Page 1 of 8 SECTION 303-01A: Engine 2.3L 2002 Ranger Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/20/2004 Intake Manifold Removal 1. Remove the accelerator control snow shield. 2. Remove

More information