Yes Minimum octane rating RON 95. Cam/ Crankshaft Fuel System. Trigger location. Air metering Combined ignition and fuel ECM. Yes Diagnostic socket
|
|
- Reginald Martin
- 5 years ago
- Views:
Transcription
1 Vehicle identification No. of cylinders Type 4/DOHC Capacity (Fiscal) cc 1998 Compression ratio :1 11,0 Suitable for unleaded petrol Minimum octane rating RON 95 Ignition system Description Map-DI Trigger location Cam/ Crankshaft Fuel system Make Toyota Fuel System Type EFI Fuel System Description MFI-s Air metering Type Mass Combined ignition and fuel ECM Diagnostic socket Ignition system Firing order Tuning and emissions 49 Tuning conditions Ignition timing - basic BTDC Engine/rpm 8-12/675 Not adjustable Ignition advance checks Engine/rpm ECM Controlled Idle speed rpm 675±50 Not adjustable Oil temperature for CO test C 80 CO level at idle speed - tailpipe Vol. % CO 0,5 Max Not adjustable HC level at idle speed ppm 100 CO2 level at idle speed Vol. % CO2 14,5-16 O2 level at idle speed Vol. % O2 0,1-0,5 Increased idle speed for CO test rpm
2 CO content at increased idle speed Vol. % 0,3 Lambda at increased idle λ 0,98-1,02 Original equipment Denso Spark plug Type SK20BR11 Electrode gap mm 1,0-1,1 Make NGK Spark plug Type IFR6A-11T Electrode gap mm 1,0-1,1 Fuel system Regulated pressure with vacuum bar 3,8-4,2 Engine coolant temperature (ECT) sensor Ohm/ C /80 RPM/TDC sensor Ohm Injector Ohm 2,55-2,85 Injector opening duration (hot) ms/rpm 0,4-0,8 Oxygen sensor heater Ohm Service checks and adjustments Valve clearance -INLET mm 0,19-0,29 cold Valve clearance -EXHAUST mm 0,30-0,40 cold Compression pressure bar 10-14,7 Oil pressure bar/rpm 2,5-5,4/3000 Radiator cap bar 0,74-1,03 Thermostat opens C Lubricants and capacities Engine oil grade - cold climate SAE 5W/30 Engine oil grade - moderate climate SAE 10W/30 Engine oil classification API/ACEA SJ/A1-98 Engine oil grade - alternative - moderate climate SAE 15W/40 Engine oil classification - alternative - moderate climate API/ACEA SJ/A1-98 Engine with filter litres 4,3 Gearbox oil grade SAE 75W/90 Semi-Synth. Gearbox 4/5 speed litres 2,2 Automatic transmission fluid Type ATF T-IV Automatic transmission (drain & refill) litres 4,1 Cooling system litres 7,7 AT=8,2 Brake fluid Type DOT 3 Power steering fluid Type Dexron III Power steering fluid litres 0,8 Tightening torques Cylinder head instructions Cylinder head Maximum bolt length 164,2 Stage 1 Tighten 40 Nm Stage 2 Tighten 7 Stage 3 Tighten 90
3 Other tightening torques 123 Main bearings Renew bolts/nuts 100 Big end bearings Renew bolts/nuts Big end bearings Stage 1 25 Nm Big end bearings Stage 2 90 Oil pump to cylinder block Sump bolts Sump drain bolt 25 Nm Flywheel/driveplate 130 Nm/83 Nm Clutch to flywheel Crankshaft pulley/damper 170 Nm Camshaft sprocket/gear 54 Nm 98 Camshaft carrier/cap 122 Camshaft/rocker cover Inlet manifold to cylinder head 30 Nm Exhaust manifold to cylinder head 37 Nm Exhaust downpipe to manifold 62 Nm Fuel rail to inlet manifold Crankshaft position (CKP) sensor Camshaft position (CMP) sensor Engine coolant temperature (ECT) sensor 20 Nm Oxygen sensor (Lambda) 44 Nm Knock sensor (KS) 44 Nm Engine oil pressure switch 13 Nm Front hub 216 Nm Steering track rod end 4 Brake caliper carrier to hub Front 94 Nm Brake caliper to carrier Rear 30 Nm Brake caliper carrier to hub Rear 47 Nm ABS sensor Front 8 Nm ABS sensor Rear 8 Nm Road wheels 103 Nm Starting and charging Battery V/RC(Ah) 12 (48) Maximum cranking amps A Alternator output at engine speed A/V/rpm 80/-/- Brake disc and drum dimensions Minimum disc thickness - ventilated Front 26 mm Minimum disc thickness Rear 9,0 mm Disc runout Front 0,05 mm Disc runout Rear 0,15 mm Minimum pad thickness Front 1 mm Minimum pad thickness Rear 1 mm Handbrake travel No. of notches 4-7 Air conditioning Air conditioning refrigerant Type R134a
4 Note 49 Air conditioning refrigerant quantity grams Air conditioning oil Type ND-Oil 8 Ignition timing, idle speed Bridge terminals 4 & 13 of data link connector in facia panel fuse block. Fig Note 123 Main bearings Min bolt diameter = 7,2 mm Tighten in the following stages: 1) 20 Nm 2) 40 Nm 3) 90. Note 100 Big end bearings Minimum bolt diameter = 7,0 mm. Fig Autodata Note 98 Camshaft carrier/cap Front caps = 30 Nm Others =. Autodata Note 122 Camshaft/rocker cover Centre bolts (x2) = 14 Nm Outer nuts/bolts (x7) = 11 Nm Outer bolts (x2) = 21 Nm.
5 Timing mark Tightening sequence
VOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ
VOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ Telephone: 01752 667007 Fax: 01752 663399 Email: mail@volkscity.com Notes Specified value Measured value Vehicle identification No. of cylinders Type
More informationVOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ
VOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ Telephone: 01752 667007 Fax: 01752 663399 Email: mail@volkscity.com 1 Accelerator pedal position (APP) sensor - above pedal 2 Brake pedal position (BPP)
More informationVOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ
VOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ Telephone: 01752 667007 Fax: 01752 663399 Email: mail@volkscity.com VAT Registration No.: 133 1580 01 1 Accelerator pedal position (APP) sensor 1/2 -
More informationPARTIAL ENGINE ASSY (2ZZ GE)
COMPONENTS 14189 140R701 7.0 (71, 62 in. lbf) Cylinder Head Cover No. 2 19 (194, 14) Radiator Support Upper 19 (194, 14) Radiator Hose Inlet Cruise Control Actuator Assy 6.0 (61, 53 in. lbf) Radiator Assy
More information2004 Acura TSX 2004 SPECIFICATIONS TSX 2004 SPECIFICATIONS
2004 SPECIFICATIONS TSX AIR CONDITIONING AUTOMATIC SYSTEM Air Conditioning Service s AIR CONDITIONING SPECIFICATIONS Compressor Type N/A Refrigerant Oil (1) Compressor Oil Capacity 4.3-5 ozs. Condenser
More informationSection 2 Engine. kw at rps hp / rpm Nm / rpm. Engine code 68 Engine management system Denso Bosch ME 7 No. of cylinders 5 5
S40 ( 04- ) Section 2 Engine Section 2 Engine Group 20 General data engines Performance and other data, petrol engines: Engine type: ( Geometric compression ratio) B5254T3 (9.0:1) Other general data Engine
More informationON-BOARD DIAGNOSTICS II SYSTEM. 5. Specified Data. Signal (V) Ignition SW ON (Engine OFF)
1. ENGINE CONTROL MODULE (ECM) I/O SIGNAL OBD0092A Crankshaft Camshaft Mass air flow Throttle Signal (+) 8 0 7 +7 Sensor output waveform Signal ( ) 29 0 0 Shield 54 0 0 Signal (+) 7 0 7 +7 Sensor output
More informationSERVICE DATA. Unit: mm (in) ITEM STD/SPEC. LIMIT Valve diam. 29 IN. (1.14) EX IN. ( ) EX.
4 STROKE VALVE + GUIDE SERVICE DATA Date: November 23, 2000 Valve diam. 29 (1.14) 24 (0.94) Valve clearance (when cold) 0.10 0.20 (0.004 0.008) 0.20 0.30 (0.008 0.012) Valve guide to valve stem 0.010 0.037
More information7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).
1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual
More informationC - SPECIFICATIONS Subaru SVX INTRODUCTION CAPACITIES ENGINE PERFORMANCE Subaru Service & Adjustment Specifications
C - SPECIFICATIONS 1992 Subaru SVX 1992 ENGINE PERFORMANCE Subaru Service & Adjustment Specifications Justy, Legacy, Loyale, SVX INTRODUCTION Use this article to quickly find specifications related to
More informationSERVICE DATA Date: August 1, 2007
SERVICE DATA Date: August 1, 2007 Model: LT-A450XK8 VALVE + VALVE GUIDE Valve diam. 30.6 IN. (1.20) EX. 27.0 (1.06) Tappet clearance (when cold) 0.05 0.10 IN. (0.002 0.004) EX. 0.17 0.22 (0.007 0.009)
More informationSERVICE DATA. Item Standard Limit Valve diam. IN (1.42) EX (1.30) Tappet clearance (When cold)
Model: LT-A750XK9 P-17, 24, 28, 33 LT-A750XZK9 P-17, 28, 33 4 STROKE Camshaft + Cylinder Head SERVICE DATA Valve + Guide Valve diam. IN. 36.0 (1.42) EX. 33.0 (1.30) Tappet clearance (When cold) IN. 0.10
More informationSERVICE DATA. Unit: mm (in) ITEM STANDARD LIMIT Valve diam. IN (1.42) EX ( ) EX.
4 STROKE VALVE + VALVE GUIDE CAMSHAFT + CYLINDER HEAD SERVICE DATA Valve diam. 36.0 (1.42) 33.0 (1.30) Tappet clearance (when cold) 0.10 0.20 (0.004 0.008) 0.20 0.30 (0.008 0.012) Valve guide to valve
More informationTIGHTENING TORQUE CHART For other nuts and bolts not listed in the preceding page, refer to this chart:
TIGHTENING TORQUE ENGINE ITEM N m kgfm lbft Cylinder head cover bolt 14 1.4 10.0 Spark plug 11 1.1 8.0 Cylinder head bolt (M10) 47 4.7 18.0 (M6) 10 1.0 7.0 Cylinder bolt 10 1.0 7.0 Camshaft journal holder
More informationValve + Valve Guide Unit: mm (in) Item Standard Limit Valve diam. IN (1.20) EX (1.06) Valve clearance (when cold)
Model: LT-A400FL9 P-17, 24, 28,03 Date: Feb. 12, 2018 SERVICE DATA Valve + Valve Guide Valve diam. IN. 30.6 (1.20) EX. 27.0 (1.06) Valve clearance (when cold) IN. 0.05 0.10 (0.002 0.004) EX. 0.22 0.27
More informationTriumph Tiger 800. Torque settings. Torque (Nm) Camshaft cover to cylinder head 10 Camshaft drive chain tensioner to head 9
Triumph Tiger 800 Torque settings Cylinder Head Camshaft cover to cylinder head 10 Camshaft drive chain tensioner to head 9 Camshaft bearing ladder to head Camshaft sprocket to camshaft 10 Camshaft drive
More informationhttps://www.hyundaitechinfo.com/viewer/content.asp?isprint=true&imgnum=1&print_titl...
Page 1 of 7 VELOSTER(FS) >2013 > G 1.6 T-GDI > Engine Mechanical System > General Information > Specifications Specifications General Type Description Specifications Except Europe In-line, DOHC Number
More information20 C (68 F) Ω C (68 86 F)
Page 1 of 10 Service Data 0C Emission Control Devices EVAP system purge control solenoid valve power supply (If equipped) EVAP system purge control solenoid valve resistance (If equipped) PAIR control
More informationGeneral Specifications
General Specifications General Engine management EEC V Emission standard 96 EC Engine code Y5A Firing order 1 3 4 2 Bore mm 89,6 Stroke mm 91 Cubic capacity cc 2295 Compression ratio 10,0:1 Compression
More informationCylinder Head Replacement
CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A
More information2003 Taurus/Sable Workshop Manual
Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
More informationLower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
More informationDISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.
303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773
More informationGeneral Specifications
General Specifications Engine Data General Engine management EEC V/SEFI Emission standard 96 EEC Engine code N3A Firing order 1-3-4-2 Bore mm 86,0 Stroke mm 86,0 Cubic capacity cc 1998 Compression ratio
More informationSERVICE SPECIFICATIONS
TO INDEX SERVICE SPECIFICATIONS SERVICE SPECIFICATIONS STANDARD BOLT HOW TO DETERMINE BOLT STRENGTH......................... SPECIFIED TORQUE FOR STANDARD BOLTS.................... HOW TO DETERMINE NUT
More information51. absolute pressure sensor
51. absolute pressure sensor Function The absolute pressure sensor measures the atmospheric pressure. Specifications supply voltage: 5 V output voltage sea level: 3.5-4.5 V output voltage at 2000m: 2.5-3.5
More information1993 ENGINE PERFORMANCE Service & Adjustment Specifications. EuroVan
Article Text ARTICLE BEGINNING 1993 ENGINE PERFORMANCE Service & Adjustment s EuroVan INTRODUCTION Use this article to quickly find specifications related to servicing and on-vehicle adjustments. This
More information(DT20C ENGINE) JLR 3.0L 24V DOHC V6 TC Diesel TYPE TIGHTENING TORQUES. Rev. 2.0 OE
(DT20C ENGINE) JLR 3.0L 24V DOHC V6 TC Diesel 1 TYPE TIGHTENING TORQUES 1. Cylinder head CAUTION : (*) Follow the tightening sequence. Reference Designation (1) bolts - Throttle butterfly housing Tightening
More informationEngine Dismantle and Assemble ( )
Engine Dismantle and Assemble ( 34 8) Special Tools 5 053 Slide hammer 47 Vibration damper remover 47 5053 00 Splined head socket, cylinder head bolts 87 Mounting stand with geared drive 00 059C Installer
More informationservice bulletin MCM 454 Magnum EFI, MIE 454 EFI Ski GM Gen V Engine Specifications No Magnum 454 EFI Model EFI Ski (Average Octane Rating)
service bulletin TO: SERVICE MANAGER MECHANICS PARTS MANAGER No. 93-25 MCM 454 Magnum EFI, MIE 454 EFI Ski GM Gen V Engine Specifications NOTE: Generation V Engines Have the Fuel Pump Mounted on the Belt
More informationMotorcycle parts compatibility on ebay.co.uk
Motorcycle parts compatibility on ebay.co.uk Review the full list of categories and subcategories in which you can list motorcycle and scooter parts. Last updated: 10 August 2016 Motorcycle Parts (10063)
More informationPARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque
ENGINE MECHANICAL 1417 COMPONENTS 141FP01 Radiator Grille Front Bumper Cover Engine Under Cover RH Engine Under Cover LH A79361 962 1418 ENGINE MECHANICAL Heater Outlet Water Hose 7.0 (71, 62 in. lbf)
More informationUpdated 26th September 2017
TECHNICAL DATA ENGINE SECTION TDP e259 General... 2 Cylinder Block... 3 Cylinder Head... 3 Valves & Springs... 3 Camshafts... 3 Pistons... 3 Connecting Rods... 4 Crankshaft... 4 Oil Pump... 4 Coolant Thermostat...
More informationENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
More informationA: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES. Signal (V) Ignition SW ON (Engine OFF) B B B
5. Specified Data A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen heater Engine coolant temperature Signal
More informationATV 2012 Model: LT-Z400/Z Date: February 2011
LT-Z400/ZL2 ATV 2012 Model: LT-Z400/Z Date: February 2011 MSRP $7,099 White (30H) Key Features 1. 398 cm3, 1-cylinder, liquid-cooled, DOHC, aluminum-alloy engine with a flat torque curve and strong response
More informationENGINE - V8. Seal - crankshaft - rear. Refit 1. Ensure both seal location and running surface on crankshaft are clean.
REPAIRS Seal - crankshaft - rear 1. Ensure both seal location and running surface on crankshaft are clean. 1. Automatic gearbox models: converter drive plate. ENGINE - V8, REPAIRS, Plate - drive - automatic.
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More informationPARTIAL ENGINE ASSY (2TR FE)
COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER
More informationDTC Summaries. NipponDenso V12 Engine Management
DTC Summaries NipponDenso V12 Engine Management OBD II MONITORING CONDITIONS: When testing for DTC reoccurrence, it can be determined if the Service Drive Cycle was of sufficient length by performing a
More informationPage 1 of 6 2008 Ford Pickup 6.4L Eng F250 Super Duty ENGINE CONTROLS - DESCRIPTION AND OPERATION - F250-F550 SUPER DUTY 6.4L (DIESEL ) FUEL SYSTEM The fuel system includes the following: low pressure
More informationGeneral Specifications
General Specifications Engine Data Description Litres Engine management EEC V/SFI Emission standard 96 EEC Engine code NSD Firing order 1-3 - 4-2 Bore mm 86,0 Stroke mm 86,0 Cubic capacity cm 3 1998 Compression
More informationPowertrain DTC Summaries EOBD
Powertrain DTC Summaries Quick Reference Diagnostic Guide Jaguar X-TYPE 2.0 L 2002.25 Model Year Refer to page 2 for important information regarding the use of Powertrain DTC Summaries. Jaguar X-TYPE 2.0
More informationSUPER MULTIPLE JUNCTION (SMJ) Installation
Installation SUPER MULTIPLE JUNCTION (SMJ) Installation NEEL0146 To install SMJ, tighten bolts until orange fulltight mark appears and then retighten to specified torque as required. :3-5N m (0.3-0.5 kg-m,
More informationSECTION B Engine 5.0L (4V)
303-01B-i Engine 5.0L (4V) 303-01B-i SECTION 303-01B Engine 5.0L (4V) CONTENTS PAGE SPECIFICATIONS... 303-01B-2 303-01B-2 Engine 5.0L (4V) 303-01B-2 SPECIFICATIONS Material Motorcraft Metal Surface Prep
More informationFUEL PUMP CAMSHAFT TIMING CHECK
PUBLISHED: 26-FEB-2018 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING CHECK (G1473740) GENERAL PROCEDURES 19.90.16 HIGH PRESSURE FUEL TIMING CHECK 5000 CC,
More informationCOMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
More informationSOUL GDI REPAIR AND MAINTENANCE
SOUL 2013-1.6 GDI REPAIR AND MAINTENANCE (First Numbers are page number within section - Numbers in parenthesis are overall document page) GENERAL INFORMATION (23 PAGES) 01-07 (01-07): Identification Number
More informationFuel and exhaust systems 4A 21
Fuel and exhaust systems 4A 21 15.40 Unscrew the union nuts and disconnect the fuel feed and return hoses from the manifold 41 Disconnect the injector wiring harness connector and the vacuum hose from
More informationTorque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC
Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC Engine Mechanical System Camshaft sprocket bolt 90 ~ 110 900 ~ 1,100 65 ~ 80 Cylinder head cover bolt 8 ~ 10 80 ~ 100 5.8 ~ 7.2 Main bearing
More informationCAMSHAFT POSITION SENSOR
IG8 IGNITION CAMSHAFT POSITION SENSOR COMPONENTS CAMSHAFT POSITION SENSOR IG08T03 Fuel Return Hose VBank Cover 7.5 (80, 66 in. lbf) Camshaft Position Sensor Camshaft Position Sensor Connector Grommet 7.5
More informationMotronic September 1998
The Motronic 1.8 engine management system was introduced with the 1992 Volvo 960. The primary difference between this Motronic system and the previous generation of Volvo LH-Jetronic engine management
More informationTUNE UP EG2 12 ENGINE MECHANICAL
EG212 TUNEUP 1. CHECK COOLANT LEVEL AT RESERVOIR TANK The engine coolant level should be between the LOW and FULL lines. If low, check for leaks and add engine coolant up to the FULL line. 2. CHECK COOLANT
More information5. Engine Control Module (ECM) I/O Signal S008526
5. Engine Control Module (ECM) I/O Signal S008526 A: ELECTRICAL SPECIFICATION S008526A08 1. MT VEHICLES S008526A0801 B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen
More informationAudi A4 Current Flow Diagram No. 44 / 1 Edition
Page 1 of 16 Audi A4 Current Flow Diagram No. 44 / 1 Edition 05.2003 1.8 l - Fuel injection engine (110 kw - Motronic - 4 cylinder), engine code AVJ from model year 2002 1.8 l - Fuel injection engine (120
More informationFUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G )
PUBLISHED: 10-OCT-2017 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G1473741) GENERAL PROCEDURES 19.90.17 HIGH PRESSURE FUEL TIMING CHECK AND
More informationTelephone: Fax: VAT Registration No.:
Telephone: Fax: VAT Registration No.: Terminal side Wire side Component/circuit description ECM pin Signal Condition Typical value Oscilloscope setting (Suggested settings - Voltage/time per division)
More information1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza
1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza ARTICLE BEGINNING 1995-98 ENGINES Subaru - 1.8L & 2.2L 4-Cylinder 1995-97: Impreza (1.8L) 1995-98: Impreza (2.2L), Legacy (2.2L) * PLEASE READ THIS FIRST
More informationCAMSHAFT POSITION SENSOR
IGNITION (2UZFE) CAMSHAFT POSITION SENSOR COMPONENTS CAMSHAFT POSITION SENSOR IG7 IG08T08 Drive Belt Camshaft Position Sensor Camshaft Position Sensor Connector Grommet Engine Wire Oil Cooler Pipe LH No.3
More informationDisconnect negative battery cable and remove coolant bottle cap.
1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use
More information2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head
Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat
More information2012 Audi Q5 2.0T. Technical specifications. Technical specifications Audi Q5 2.0 TFSI. Page 1 of 2 ENGINE:
2012 Audi Q5 2.0T 2012 Audi Q5 2.0 TFSI ENGINE: Arrangement Inline four-cylinder gasoline engine with FSI direct injection, exhaust turbocharger with intercooler, four valves per cylinder Front mounted,
More informationservice bulletin MCM 7.4L Bravo, MIE 7.4L Inboard GM Generation V Engine Specifications No. 91-6
service bulletin TO: SERVICE MANAGER MECHANICS PARTS MANAGER No. 91-6 MCM 7.4L Bravo, MIE 7.4L Inboard GM Generation V Engine Specifications NOTE: Generation V Engines Have the Fuel Pump Mounted on the
More informationEngine management/transmission
MAZDA Model: 323 (BG) 323 Estate 1,6/4x4 (BW) 323 (BA/BJ) 626/MX-6 626/Estate Xedos 6/9 MX-3/MX-5 Year: 1989-00 Engina code: BP, BP-DOHC, B3, B3E, B6, B6-SOHC, B6-DOHC, B6E,FP, FS, KF, KJ, KL K8, RF, RF-CX,
More informationVOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ
VOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ Telephone: 01752 667007 Fax: 01752 663399 Email: mail@volkscity.com 1 Camshaft position (CMP) sensor 1 2 Camshaft position (CMP) sensor 2 3 Camshaft position
More information1992 Toyota Cressida
Monday, May 16, 2016 5:32:47 PM Page 13 2005 Mitchell Repair Information Company, LLC. Fig. 7: Exploded View Of Typical Cylinder Head & Components Fig. 8: Cylinder Head Bolt Removal Sequence Monday, May
More informationTECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS The information shown is based on data available at the time of publication (June, 2006). Body and Chassis Five-seater, four-door sedan, all-steel unitary body chassis. Choice
More information11A-1 ENGINE CONTENTS
11A-1 ENGINE CONTENTS ENGINE ENGINE ... 11A... 11B 11A-2 ENGINE CONTENTS GENERAL... 3 Outline of Changes... 3 GENERAL INFORMATION... 3 SERVICE SPECIFICATIONS... 3 SEALANT... 3 SPECIAL
More informationMotorcycle 2012 Model: RM-Z450 Date: August 2011
RM-Z450L2 Motorcycle 2012 Model: RM-Z450 Date: August 2011 New Feature New graphics Key Features 1. 449cm3 4-stroke liquid-cooled DOHC 4-valve fuel-injected engine developed and refined to deliver phenomenal
More information2002 Explorer Sport/Sport Trac Workshop Manual
Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)
More informationIG 1 1NZ-FE IGNITION IGNITION SYSTEM IGNITION SYSTEM ECM IGNITION COIL NO. 1 CAMSHAFT POSITION SENSOR SPARK PLUG CRANKSHAFT POSITION SENSOR A116185E01
NITION SYSTEM EINE 1NZ-FE PARTS LOCATION 1NZ-FE NITION NITION SYSTEM 1 ECM NITION COIL NO. 1 CAMSHAFT POSITION SENSOR SPARK PLUG CRANKSHAFT POSITION SENSOR A116185E01 2 1NZ-FE NITION NITION SYSTEM SYSTEM
More informationDIAGNOSTIC TROUBLE CODE CHART
DIAGNOSTIC TROUBLE CODE CHART 05 35 HINT: As for the vehicle for MEXICO, refer to Repair Manual 2003 COROLLA MATRIX (Pub. No. RM940U). Parameters listed in the chart may not be exactly the same as your
More informationASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s)
303-01A-1 ASSEMBLY Engine Special Tool(s) Tensioner, Timing Chain 303-571 (T97T-6K254-A) Special Tool(s) 303-01A-1 Installer, Crankshaft Vibration Damper 303-102 (T74P-6316-B) Holding Tool, Camshaft Sprocket
More informationEngine Dismantle and Assemble ( )
Engine Dismantle and Assemble (21 134 8) Special Tools 15-030A Universal flange-holding wrench 21147 21-147 Vibration damper remover 15030A 16-067 Locator for clutch disc 21-167 Wrench for cylinder head
More information2.8 Liter VR6 2V Fuel Injection & Ignition, Engine Code(s): AAA m.y
2.8 Liter VR6 2V Fuel Injection & Ignition, Engine Code(s): AAA m.y. 1996-1997 01 - On Board Diagnostic (OBD) On Board Diagnostic (OBD II) Malfunction Indicator Lamp (MIL) On Board Diagnostic (OBD II),
More informationSECTION A Engine 3.7L
303-01A-i Engine 3.7L 303-01A-i SECTION 303-01A Engine 3.7L CONTENTS PAGE SPECIFICATIONS... 303-01A-2 303-01A-2 Engine 3.7L 303-01A-2 SPECIFICATIONS Material Motorcraft High Performance Engine RTV Silicone
More informationPage 1 of 9 SECTION 303-01B: Engine 2.0L SPI 2002 Focus Workshop Manual ASSEMBLY Procedure revision date: 12/14/2000 Engine Special Tool(s) Crankshaft Rear Seal Pilot 303-329 (T88P-6701-B2) Crankshaft
More informationSC300/400 NEW FEATURES. 1UZ FE Engine Item No. of Cyls. & Arrangement 8 Cylinder, V Type
51 1UZ FE ENGINE 1. Description Various improvement have been made to the 1UZ FE engine in order to realize weight reduction and low friction performance. As a result, the engine provides both high power
More informationINTAKE MANIFOLD INSPECTION/REPLACEMENT
ATTACHMENT III Owner Notification Program 99M01 INTAKE MANIFOLD INSPECTION/REPLACEMENT AFFECTED VEHICLES: 1997 AND 1998 CROWN VICTORIA POLICE INTERCEPTOR VEHICLES WITH 4.6L SOHC ENGINES BUILT AT THE ST.
More informationSECTION C Engine 5.4L (4V)
303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 SPECIFICATIONS Material Motorcraft Metal Surface Prep
More informationIGNITION SYSTEM 8D - 1 IGNITION SYSTEM TABLE OF CONTENTS
LH IGNITION SYSTEM 8D - 1 IGNITION SYSTEM TABLE OF CONTENTS page AND IGNITION SYSTEM...1 SPARK PLUGS-PLATINUM....1 COIL ON PLUG...1 CRANKSHAFT POSITION SENSOR....2 CAMSHAFT POSITION SENSOR....3 KNOCK SENSOR....5
More informationMotorcycle 2012 Model: VZR1800/ZL2 Date: April 2011
VZR1800/ZL2 Motorcycle 2012 Model: VZR1800/ZL2 Date: April 2011 MSRP $14,299 Glass Sparkle Black (YVB) Key Features 1. 1783cm3, liquid-cooled, DOHC, V-Twin engine is designed to produce a massive tractable
More informationIG 1 2GR-FE IGNITION IGNITION SYSTEM IGNITION SYSTEM ECM ENGINE ROOM R/B - IG2 FUSE - ST/AM FUSE IGNITION COIL NOISE FILTER NOISE FILTER A137458E01
NITION SYSTEM ENGINE 2GR-FE PARTS LOCATION 2GR-FE NITION NITION SYSTEM 1 ECM ENGINE ROOM R/B - 2 FUSE NITION COIL - ST/AM FUSE NOISE FILTER NOISE FILTER A137458E01 2 2GR-FE NITION NITION SYSTEM SYSTEM
More informationMotorcycle - Specifications
Motorcycle - Specifications Model Name FZ400R Model Code 46X0 Model Year 1985 Destination JAPAN Section/Item Chassis Maintenance Specification (Chassis) Chassis Frame type Double cradle Caster angle 26.00
More informationTorque Guidelines (Z 22 SE)
Page 1 of 14 Torque Guidelines (Z 22 SE) No. Designation Nm 1 Retaining bolts, coolant pump sprocket to coolant pump 2 Retaining bolts, balancer shaft timing chain guide rail to 3 Retaining bolts, balancer
More informationMotronic injection system,
Page 1 of 78 24-1 Motronic injection system, servicing Safety precautions If special testing equipment is required during road test, note the following: WARNING! Scan tools and testing devices must always
More informationTechnical data. Part Thread (mm) Nm ±10% Tolerance Sidestand
section 3 - Torque settings Frame torque settings Sidestand Stand sensor bolt 5 Pre-applied threadlocker Stand plate fixing screw M10x25 43 Pre-applied threadlocker Side stand fastening pin Side stand
More informationTORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket Bolts Upper Vertical Bolt 16-21 (22-29) Horizontal Bolts 32-43 (43-58) A/C Compressor-To-Bracket Bolts 32-43
More informationIntake Components 1117
Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold
More information1.6L 4-CYL - VIN [E]
1.6L 4-CYL - VIN [E] 1993 Nissan Sentra 1993 NISSAN ENGINES 1.6L 4-Cylinder NX, Sentra * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES
More information2.2L 4-CYL - VIN [S]
2.2L 4-CYL - VIN [S] 1994 Toyota Celica 1994 ENGINES Toyota 2.2L 4-Cylinder Celica NOTE: For repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article
More informationPiaggio BV 350. Function, Form, Finish and Performance Wow!
Piaggio BV 350 Function, Form, Finish and Performance Wow! Revolutionary 4 Valve 350cc Engine This engine is only 60cc larger in displacement but develops 50% more power than the h existing 300. 4 VALVE
More informationENGINE 3S GTE ENGINE DESCRIPTION ENGINE 3S GTE ENGINE
39 ENGINE 3S GTE ENGINE DESCRIPTION The new MR2 has the 2.0 liter, 16 valve, DOHC 3S GTE engine with turbocharger which is used in the Celica All Trac/4WD models and has been well received. The 3S GTE
More informationCylinder Head Removal
2006 Odyssey Cylinder Head Removal Report a problem with this article NOTE: Use fender covers to avoid damaging painted surfaces. To avoid damaging the wires and terminals, unplug the wiring connectors
More informationFastener Tightening Specifications Specification
2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt
More informationCooling system components, removing and installing
Page 1 of 40 19-1 Cooling system components, removing and installing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate
More information5. Control System CONTROL SYSTEM FUEL INJECTION (FUEL SYSTEM) A: GENERAL FU(H4DOTC)-29
W1860BE.book Page 29 Tuesday, January 28, 2003 11:01 PM 5. Control System A: GENERAL The ECM receives signals from various sensors, switches, and other control modules. Using these signals, it determines
More information1ZZ-FE ENGINE CONTROL SYSTEM SFI SYSTEM. DTC P0300 Random / Multiple Cylinder Misfire Detected ECM
164 DTC P0300 Random / Multiple Cylinder Misfire Detected DTC P0301 Cylinder 1 Misfire Detected DTC P0302 Cylinder 2 Misfire Detected DTC P0303 Cylinder 3 Misfire Detected DTC P0304 Cylinder 4 Misfire
More informationThe 1.4 ltr. and 1.6 ltr. FSI engine with timing chain
Service. Self study programme 296 The 1.4 ltr. and 1.6 ltr. FSI engine with timing chain Design and function For Volkswagen, new and further development of engines with direct petrol injection is an important
More information