Cylinder Head Removal

Size: px
Start display at page:

Download "Cylinder Head Removal"

Transcription

1 2006 Odyssey Cylinder Head Removal Report a problem with this article NOTE: Use fender covers to avoid damaging painted surfaces. To avoid damaging the wires and terminals, unplug the wiring connectors carefully while holding the connector portion. To avoid damaging the cylinder head, wait until the engine coolant temperature drops below 100 ºF (38 ºC) before loosening the cylinder head bolts. Mark all wiring and hoses to avoid misconnection. Also, be sure that they do not contact other wiring or hoses, or interfere with other parts. 1. Make sure you have the anti-theft codes for the radio and the navigation system, then write down the customer's audio presets. Make sure the ignition switch is OFF. 2. Relieve fuel pressure. 3. Disconnect the negative cable from the battery. 4. Drain the engine coolant. 5. Remove the drive belt. 6. Remove the power steering (P/S) pump (A) and the bolt (B) securing the P/S hose bracket. 7. Remove the alternator. 8. Remove the timing belt. 9. Remove the intake manifold. 10. Remove the six ignition coils. 11. Remove the engine wire harness connectors and wire harness clamps from the cylinder head. Six injector connectors Engine coolant temperature (ECT) sensor 1 connector Engine coolant temperature (ECT) sensor 2 connector Camshaft position (CMP) sensor connector Crankshaft position (CKP) sensor A/B connector Exhaust gas recirculation (EGR) valve connector Rocker arm oil control solenoid (VTEC solenoid valve) connector 1/13

2 Rocker arm oil pressure switch (VTEC oil pressure switch) connector Oil pressure switch connector Two air fuel ratio (A/F) sensor connectors Two secondary heated oxygen sensor (secondary HO2S) connectors 12. Remove the front warm up three way catalytic converter (front WU-TWC) and rear warm up three way catalytic converter (rear WU-TWC). 13. Remove the quick-connect fitting cover (A), then disconnect the fuel feed hose (B). 2/13

3 14. Remove the harness clamp, then remove harness holder stay bolt (A). 15. Remove the harness holder (B) from the stay. 3/13

4 16. Remove the upper radiator hose (A) and lower radiator hose (B). 4/13

5 17. Remove the heater hose (A) and water bypass hose (B). 5/13

6 18. Remove the evaporative emission (EVAP) canister hose joint (A) with bracket. 6/13

7 19. Remove the harness bracket from the front cylinder head. 7/13

8 20. Remove the harness clamp bracket from the rear cylinder head. 8/13

9 21. Remove the fuel rails. 9/13

10 22. Remove the water passage. 10/13

11 23. Remove the front and rear camshaft pulleys (A) and front and rear back covers (B). 24. Remove the cylinder head covers. 11/13

12 25. Remove the cylinder head bolts. To prevent warpage, unscrew the bolts in sequence 1/3 turn at a time; repeat the sequence until all bolts are loosened. 26. Remove the cylinder heads. 12/13

13 13/13

Cylinder Head Replacement

Cylinder Head Replacement CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A

More information

Lower Intake Manifold Replacement

Lower Intake Manifold Replacement Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the

More information

7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).

7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L). 1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual

More information

2004 Honda ELEMENT. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS. Engine Installation. Special Tools Required

2004 Honda ELEMENT. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS. Engine Installation. Special Tools Required 2004 Honda ELEMENT Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS Engine Installation Special Tools Required Engine hanger/adapter VSB02C000015 Engine support hanger, A & Reds AAR-T-12566

More information

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie

More information

DISASSEMBLY Procedure revision date: 11/22/2001

DISASSEMBLY Procedure revision date: 11/22/2001 Page 1 of 31 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:06 PM To: 'Evan Groenke' Subject: 2.5 L Engine Disassembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop

More information

Service Bulletin

Service Bulletin Service Bulletin 13-080 February 03, 2018 08193 Version 7 Warranty Extension: MIL Comes On With DTCs P0301 thru P0304 Supersedes 13-080, dated May 18, 2016, to revise the information highlighted in yellow.

More information

Service Bulletin

Service Bulletin Service Bulletin 13-081 February 03, 2018 08191 Version 13 Warranty Extension: MIL Comes On With DTCs P0301 thru P0304 Supersedes 13-081, dated January 23, 2018, to revise the information highlighted in

More information

Service Bulletin. Applies To: MDX ALL 2006 MDX From VIN 2HNYD18..6H thru 2HNYD18..6H535538

Service Bulletin. Applies To: MDX ALL 2006 MDX From VIN 2HNYD18..6H thru 2HNYD18..6H535538 Service Bulletin Applies To: 2003 05 MDX ALL 2006 MDX From VIN 2HNYD18..6H500001 thru 2HNYD18..6H535538 06-028 July 13, 2007 MIL Comes On With DTC P0335, P0339, P0385, or P0389, and the Engine Runs Roughly

More information

Cylinder Head Installation...

Cylinder Head Installation... Engine Mechanical Cylinder Head Special Tools.... 6-2 Component Location Index.... 6-3 Engine Compression Inspection.... 6-6 VTEC Rocker rm Test.... 6-7 Valve Clearance djustment.... 6-8 Crankshaft Pulley

More information

Service Bulletin

Service Bulletin Service Bulletin 13-082 May 18, 2015 51869-02164 Version 7 Warranty Extension: MIL Comes On With DTCs P0301 thru P0304 Supersedes 13-082, dated September 12, 2015, to revise the information highlighted

More information

Service Bulletin TSX: Sticking Rings Resulting in Unusually High Engine Oil Consumption

Service Bulletin TSX: Sticking Rings Resulting in Unusually High Engine Oil Consumption Applies To: 2009 10 TSX L4 with M/T ALL Service Bulletin 13-006 February 22, 2013 2009 10 TSX: Sticking Rings Resulting in Unusually High Engine Oil Consumption SYMPTOM The engine oil level is low on the

More information

Service Bulletin

Service Bulletin Service Bulletin 12-087 Applies To: See VEHICLES AFFECTED August 17, 2013 2008 11 Accord L4: Sticking Rings Resulting in Unusually High Engine Oil Consumption (Supersedes 12-087, dated April 30, 2013,

More information

ENGINE REMOVAL Honda Accord EX. Special Tools Required

ENGINE REMOVAL Honda Accord EX. Special Tools Required ENGINE REMOVAL Special Tools Required 2008 V6 Attachment Arm SIL02C000033* Engine Support Hanger, A and Reds AAR-T1256* Engine Hanger Balance Bar VSB02C000019* Subframe Adapter VSB02C000016* *Available

More information

COMPONENT LOCATOR > DISASSEMBLED VIEWS

COMPONENT LOCATOR > DISASSEMBLED VIEWS Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine

More information

Telephone: Fax: VAT Registration No.:

Telephone: Fax: VAT Registration No.: Telephone: Fax: VAT Registration No.: Terminal side Wire side Component/circuit description ECM pin Signal Condition Typical value Oscilloscope setting (Suggested settings - Voltage/time per division)

More information

Valve Clearance Adjustment

Valve Clearance Adjustment 2006 Odyssey Valve Clearance Adjustment Report a problem with this article NOTE: Adjust the valves only when the cylinder head temperature is less than 100 ºF (38 ºC). 1. Remove the intake manifold. 2.

More information

2002 Explorer Sport/Sport Trac Workshop Manual

2002 Explorer Sport/Sport Trac Workshop Manual Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)

More information

Disconnect the breather tube from the air cleaner outlet duct.

Disconnect the breather tube from the air cleaner outlet duct. Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from

More information

VOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ

VOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ VOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ Telephone: 01752 667007 Fax: 01752 663399 Email: mail@volkscity.com 1 Camshaft position (CMP) sensor 1 2 Camshaft position (CMP) sensor 2 3 Camshaft position

More information

2013 Kia Optima L4-2.0L Turbo

2013 Kia Optima L4-2.0L Turbo 1 of 13 5/29/2016 11:34 AM 2013 Kia Optima L4-2.0L Turbo Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement Removal CAUTION: Use fender covers to avoid damaging painted

More information

Telephone: Fax: VAT Registration No.:

Telephone: Fax: VAT Registration No.: Telephone: Fax: VAT Registration No.: Name: Manufacturer: Ford Address: Model: Year: 1994 Registration: Tel - Private: Tel - Business: Mileage: Job number: Terminal side Wire side Component/circuit description

More information

Service Bulletin

Service Bulletin Service Bulletin 12-087 March 31, 2017 06117 Version 6 Warranty Extension: Sticking Rings Resulting in High Engine Oil Consumption Supersedes 12-087, dated April 20, 2016, to revise the information highlighted

More information

Fastener Tightening Specifications Specification

Fastener Tightening Specifications Specification 2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt

More information

2003 Taurus/Sable Workshop Manual

2003 Taurus/Sable Workshop Manual Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)

More information

Service Bulletin

Service Bulletin Service Bulletin 16-101 March 31, 2017 06141 Version 3 Warranty Extension: 2012 13 Insight Oil Consumption Exceeds Customer Expectations Supersedes 15-015, dated March 17, 2017, to revise the information

More information

Timing Belt: Service and Repair Removal

Timing Belt: Service and Repair Removal 2001 Honda Civic DX Sedan L4-1668cc 1.7L SOHC MFI Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Removal Special Tools Required ^ Holder handle 07JAB-001020A ^ Holder attachment,

More information

10/30/2018 Intake Manifold Replacement (RPOs LY2/LY6) 2007 GMC Truck Yukon Denali MotoLogic

10/30/2018 Intake Manifold Replacement (RPOs LY2/LY6) 2007 GMC Truck Yukon Denali MotoLogic 2007 Yukon Denali Applies to: 4.8L, 5.3L, 6.0L and 6.2L Report a problem with this article Removal Procedure 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Resonator Outlet Duct Replacement.

More information

2002 Mustang Workshop Manual

2002 Mustang Workshop Manual Page 1 of 13 SECTION 303-01B: Engine 4.6L (2V) 2002 Mustang Workshop Manual REMOVAL Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Remover, Crankshaft Vibration Damper 303-009 (T58P-6316-D)

More information

REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM 14)

REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM 14) EM34 ENGINE MECHANICAL (2UZFE) EM11U02 REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM14) A02844 Be careful not to drop

More information

ARTICLE BEGINNING INTRODUCTION IGNITION SYSTEM CAMSHAFT POSITION (CMP) SENSOR DISTRIBUTOR

ARTICLE BEGINNING INTRODUCTION IGNITION SYSTEM CAMSHAFT POSITION (CMP) SENSOR DISTRIBUTOR Article Text Thursday, August 19, 1999 11:40PM ARTICLE BEGINNING 1996 ENGINE PERFORMANCE Volkswagen Removal, Overhaul & Installation - Gasoline Cabrio, Golf III, GTI, Jetta III, Passat CAUTION: When battery

More information

Service Bulletin

Service Bulletin Service Bulletin 12-089 Applies To: See VEHICLES AFFECTED April 30, 2013 2010 CR-V: Sticking Rings Resulting in Unusually High Engine Oil Consumption (Supersedes 12-089, dated April 3, 2013, to revise

More information

Drawing Page Drawing Page

Drawing Page Drawing Page Contents Drawing Page Drawing Page L4 Engine...1 L4 Engine - Exploded View...2 V6 Engine...3 V6 Engine - Exploded View... 4 Oil Filter...5 VTEC (Variable Timing Electronic Control) System... 6 Fuel and

More information

Service Bulletin

Service Bulletin Service Bulletin 13-006 April 16, 2016 49236-01602 Version 6 Warranty Extension: Sticking Rings Resulting in High Engine Oil Consumption Supersedes 13-006, Sticking Rings Resulting in Unusually High Engine

More information

Intake Manifold Removal and Installation

Intake Manifold Removal and Installation 2004 Element Intake Manifold Removal and Installation Exploded View Removal Report a problem with this article 1. Disconnect the intake air temperature (IAT) sensor connector (A). 2. Remove the vacuum

More information

ASSEMBLY Procedure revision date: 11/22/2001

ASSEMBLY Procedure revision date: 11/22/2001 Page 1 of 39 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:08 PM To: 'Evan Groenke' Subject: 2.5L Engine Re-assembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop

More information

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components. 4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,

More information

REMOVAL 7. DISCONNECT ACCELERATOR CABLE FROM THROTTLE BODY. 8. DISCONNECT HOSES (a) Remove the 2 bolts from the air intake chamber assembly.

REMOVAL 7. DISCONNECT ACCELERATOR CABLE FROM THROTTLE BODY. 8. DISCONNECT HOSES (a) Remove the 2 bolts from the air intake chamber assembly. ENGINE MECHANICAL (VZFE) EM9 REMOVAL EM1MP01 1. REMOVE ENGINE UNDER COVER. DRAIN ENGINE COOLANT. REMOVE FRONT EXHAUST PIPE (See page EM10 ). DISCONNECT HEATER HOSE. REMOVE AIR CLEANER ASSEMBLY 6. REMOVE

More information

DISASSEMBLED VIEWS. Disassembled Views. Engine Covers and Component Assemblies (1 of 2) (LF1, LFW or LFX)

DISASSEMBLED VIEWS. Disassembled Views. Engine Covers and Component Assemblies (1 of 2) (LF1, LFW or LFX) 2012 Cadillac CTS Wagon AWD V6-3.0L Vehicle > Engine, Cooling and Exhaust > Engine > Locations > Components DISASSEMBLED VIEWS Disassembled Views Engine Covers and Component Assemblies (1 of 2) (LF1, LFW

More information

Service Bulletin. DTC Detection Item Associated Monitor

Service Bulletin. DTC Detection Item Associated Monitor Service Bulletin 03-010 Applies To: All OBD II equipped models except SLX March 29, 2003 OBD II DTCs and Their Associated Monitors This is a list of all DTCs for all OBD II models. No one model has all

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove

More information

2003 RSX - Intake Manifold Removal and Installation

2003 RSX - Intake Manifold Removal and Installation 2003 RSX - Intake Manifold Removal and Installation Exploded View - K20A3 Engine Removal - K20A3 Engine 1. Remove the intake manifold cover. 2. Disconnect the intake air temperature (IAT) sensor connector

More information

A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES. Signal (V) Ignition SW ON (Engine OFF) B B B

A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES. Signal (V) Ignition SW ON (Engine OFF) B B B 5. Specified Data A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen heater Engine coolant temperature Signal

More information

Diagnostic Trouble Code (DTC) memory, checking and erasing

Diagnostic Trouble Code (DTC) memory, checking and erasing Page 1 of 49 01-12 Diagnostic Trouble Code (DTC) memory, checking and erasing Check DTC Memory (function 02) - Connect VAS5051 tester Page 01-7 and select vehicle system "01 - Engine electronics". Engine

More information

For Troubleshooting of DTC related components, see chart on page INTAKE AIR BYPASS (IAB) HIGH CONTROL SOLENOID

For Troubleshooting of DTC related components, see chart on page INTAKE AIR BYPASS (IAB) HIGH CONTROL SOLENOID Index For Troubleshooting of DTC related components, see chart on page 11-53. '96-99 models: EXHAUST GAS RECIRCULATION (EGR) and LIFT MANIFOLD ABSOLUTE PRESSURE (MAP) INTAKE AIR BYPASS (IAB) HIGH page

More information

The following tools will be required to perform this new service procedure outlined in this bulletin:

The following tools will be required to perform this new service procedure outlined in this bulletin: The following new service information outlined in this bulletin will aid technicians in removal and installation of the cylinder head without the removal of the front engine cover. The new service procedure

More information

Page 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description

More information

REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide.

REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide. EM34 ENGINE MECHANICAL (2RZFE, 3RZFE) P23426 EM1MY01 REMOVAL 1. DRAIN ENGINE COOLANT 2. DISCONNECT THESE CABLES: (a) Disconnect the accelerator cable from the throttle body. A/T: Disconnect the throttle

More information

Engine Removal/lnstaIlation

Engine Removal/lnstaIlation Engine Removal/lnstaIlation Removal Make sure jacks and safety stands are placed properly and hoist brackets are attached to the correct positions on the engine. Make sure the vehicle will not roll off

More information

Diagnostic Trouble Code (DTC) table

Diagnostic Trouble Code (DTC) table Page 1 of 40 01-19 Diagnostic Trouble Code (DTC) table Note: When malfunctions occur in monitored sensors or components, Diagnostic Trouble Codes (DTCs) are stored in DTC memory with a description of the

More information

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) 1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15

More information

Diagnostic Trouble Code (DTC) List - Vehicle

Diagnostic Trouble Code (DTC) List - Vehicle Document ID# 850406 2002 Pontiac Firebird Diagnostic Trouble Code (DTC) List - Vehicle DTC DTC 021 and/or 031 DTC 022 and/or 032 DTC 023 or 033 DTC 24/34 DTC 025 and/or 035 DTC 041 DTC 042 DTC 043 DTC

More information

ELECTRONIC ENGINE CONTROLS

ELECTRONIC ENGINE CONTROLS 2005 Jaguar S-Type (X200) V8-4.2L Vehicle > Powertrain Management > Computers and Control Systems > Description and Operation > Components ELECTRONIC ENGINE CONTROLS Electronic Engine Controls Vehicles

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Procedures» Removal Cylinder Heads http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=376&nonstandardid=682956&vehicleid=45317&windowname=maina

More information

5. Engine Control Module (ECM) I/O Signal S008526

5. Engine Control Module (ECM) I/O Signal S008526 5. Engine Control Module (ECM) I/O Signal S008526 A: ELECTRICAL SPECIFICATION S008526A08 1. MT VEHICLES S008526A0801 B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen

More information

2011 Mercury Grand Marquis LS

2011 Mercury Grand Marquis LS Fig. 6: Locating Intake Manifold Crash Bracket With Tie Strap 24. Remove the intake manifold crash bracket bolt. 25. Disconnect the fuel rail pressure and temperature sensor vacuum and electrical connectors.

More information

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary. Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

More information

10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L

10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L 2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN

More information

INTAKE MANIFOLD INSPECTION/REPLACEMENT

INTAKE MANIFOLD INSPECTION/REPLACEMENT ATTACHMENT III Owner Notification Program 99M01 INTAKE MANIFOLD INSPECTION/REPLACEMENT AFFECTED VEHICLES: 1997 AND 1998 CROWN VICTORIA POLICE INTERCEPTOR VEHICLES WITH 4.6L SOHC ENGINES BUILT AT THE ST.

More information

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION

More information

5. Engine Control Module (ECM) I/O Signal

5. Engine Control Module (ECM) I/O Signal 5. A: ELECTRICAL SPECIFICATION B134 B135 B136 B137 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 19 18 34 33 32 31 30 29 28 19 18 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 35 34 33 32 31

More information

Cylinder Head Assembly: Removal and Replacement Repair Procedures

Cylinder Head Assembly: Removal and Replacement Repair Procedures 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA 10.52 Page 1 Cylinder Head Assembly: Removal and Replacement Repair Procedures COMPONENT 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA 10.52 Page 2 REMOVAL Engine

More information

5. Control System CONTROL SYSTEM FUEL INJECTION (FUEL SYSTEM) A: GENERAL FU(H4DOTC)-29

5. Control System CONTROL SYSTEM FUEL INJECTION (FUEL SYSTEM) A: GENERAL FU(H4DOTC)-29 W1860BE.book Page 29 Tuesday, January 28, 2003 11:01 PM 5. Control System A: GENERAL The ECM receives signals from various sensors, switches, and other control modules. Using these signals, it determines

More information

Intake Components 1117

Intake Components 1117 Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold

More information

Cylinder Head. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Compressor, Valve Spring

Cylinder Head. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Compressor, Valve Spring SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual REMOVAL Procedure revision date: 03/15/2009 Cylinder Head Special Tool(s) 3-Jaw Puller 303-D121 or equivalent Compressor, Valve Spring 303-1039

More information

Powertrain DTC Summaries EOBD

Powertrain DTC Summaries EOBD Powertrain DTC Summaries Quick Reference Diagnostic Guide Jaguar S-TYPE V6, V8 N/A and V8 SC 2002.5 Model Year Refer to pages 2 9 for important information regarding the use of Powertrain DTC Summaries.

More information

DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.

DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage. 303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773

More information

Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent

Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty

More information

SECTION 6A ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)

SECTION 6A ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-1 SECTION 6A ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) WARNING: For vehicles equipped with Supplemental Restraint (Air Bag) System: Service on and

More information

Auto Diagnosis Test #7 Review

Auto Diagnosis Test #7 Review Auto Diagnosis Test #7 Review Your own hand written notes may be used for the 1 st 10 minutes of the test Based on Chapters 25, 26, 32, 33, 34 and Lab Demonstrations Auto Diagnosis Test #7 Review Your

More information

Timing Chain - Renew ( )

Timing Chain - Renew ( ) «Scorpio '95 Table of Contents» «Section 21: Engine» «Subsection 21-05: 2,9 V6 24V Cosworth Engine» «REMOVAL AND INSTALLATION» Timing Chain - Renew (21 314 0) Special Tools 21-140-01Adaptor for 21-140

More information

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly. ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.

More information

EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4SO

EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4SO EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4SO SYSTEM OVERVIEW 1. System Overview There are three emission control systems, which are as follows: Crankcase emission control system Exhaust emission

More information

Transmission, removing and

Transmission, removing and Page 1 of 20 34-18 Transmission, removing and installing Removing Special tools and equipment 3282 transmission support 3282/10 adjustment plate 3337 ring spanner 7-piece set VAG1383A engine/transmission

More information

Page 1 of 6 2008 Ford Pickup 6.4L Eng F250 Super Duty ENGINE CONTROLS - DESCRIPTION AND OPERATION - F250-F550 SUPER DUTY 6.4L (DIESEL ) FUEL SYSTEM The fuel system includes the following: low pressure

More information

STARTER COMPONENTS FOR REMOVAL AND INSTALLATION

STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Removal STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Starter Components For Removal And Installation REMOVAL OF STARTER 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started

More information

Cylinder head/gasket, replacing

Cylinder head/gasket, replacing 1(16) Cylinder head/gasket, replacing Special tools: 951 2666, 951 2767, 999 5450, 999 5452, 999 5454, 999 5670, 999 5718, 999 5719, 999 5750, 999 5972 Removing the cylinder head gasket Note! As the illustrations

More information

1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6

1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6 INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle

More information

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat

More information

Oxygen sensor control,

Oxygen sensor control, Page 1 of 46 24-71 Oxygen sensor control, checking Oxygen sensor and oxygen sensor control before catalytic converter, checking Special Tools and Equipment VAG1526A VAG1594A VAG1598/31 VAS5051 with VAG5051/1

More information

Oxygen sensor control,

Oxygen sensor control, Page 1 of 37 24-71 Oxygen sensor control, checking Oxygen sensor and oxygen sensor control before catalytic converter, checking Special tools and equipment - or VAG1526A VAG1594A VAG1598/31 VAS5051 with

More information

REMOVAL. Cylinder Head. All cylinder heads. 1. Remove the engine. For additional information, refer to Engine in this section.

REMOVAL. Cylinder Head. All cylinder heads. 1. Remove the engine. For additional information, refer to Engine in this section. 303-01B-1 303-01B-1 REMOVAL Cylinder Head Material Item Specification Special Tool(s) Motorcraft Metal Surface Prep Modular Engine Lift Bracket ZC-31 303-F047 (014-00073) or equivalent Silicone Gasket

More information

2002 Crown Victoria/Grand Marquis Workshop Manual

2002 Crown Victoria/Grand Marquis Workshop Manual Page 1 of 24 SECTION 303-01: Engine 2002 Crown Victoria/Grand Marquis Workshop Manual INSTALLATION Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Installer, Crankshaft Vibration Damper

More information

2001 Ranger Workshop Manual. 1. Drain the cooling system. For additional information, refer to Section

2001 Ranger Workshop Manual. 1. Drain the cooling system. For additional information, refer to Section Exhaust Gas Recirculation (EGR) Valve 2.3L 1. Drain the cooling system. For additional information, refer to Section 303-03. 2. Disconnect the battery ground cable. For additional information, refer to

More information

Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)

Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR) SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,

More information

DIAGNOSTIC TROUBLE CODE CHART HINT:

DIAGNOSTIC TROUBLE CODE CHART HINT: DIAGNOSTICS DIAGNOSTIC TROUBLE CODE CHART HINT: SFI SYSTEM (1MZFE) 05241 Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument or other factors. If a

More information

Timing Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar

Timing Chain Renew ( ) Renew. Section Title. Special Tools. Proprietary Tools Scraper Engine support bar Timing Chain Renew ( 34 0) Special Tools 40 400 40 Engine support bar 40 0 Adaptor for -40 40 03 Adaptor for -40 Proprietary Tools Scraper Workshop Equipment Transmission jack Materials Cable ties Sealer

More information

1999 E-Series Workshop Manual

1999 E-Series Workshop Manual http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998

More information

CONDITIONS FOR RUNNING THE DTC

CONDITIONS FOR RUNNING THE DTC SYSTEM DESCRIPTION The powertrain control module (PCM) uses information from the crankshaft position (CKP) sensor and the camshaft position (CMP) sensor in order to determine when an engine misfire is

More information

Powertrain DTC Summaries EOBD

Powertrain DTC Summaries EOBD Powertrain DTC Summaries Quick Reference Diagnostic Guide Jaguar X-TYPE 2.0 L 2002.25 Model Year Refer to page 2 for important information regarding the use of Powertrain DTC Summaries. Jaguar X-TYPE 2.0

More information

SECTION 6B ENGINE COOLING

SECTION 6B ENGINE COOLING ENGINE COOLING 6B-1 SECTION 6B ENGINE COOLING NOTE: For the descriptions (items) not found in this section, refer to the same section of Service Manual mentioned in FOREWORD of this manual. CONTENTS GENERAL

More information

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting

More information

E - THEORY/OPERATION - TURBO

E - THEORY/OPERATION - TURBO E - THEORY/OPERATION - TURBO 1995 Volvo 850 1995 ENGINE PERFORMANCE Volvo - Theory & Operation 850 - Turbo INTRODUCTION This article covers basic description and operation of engine performance-related

More information

PGM-FI ( Models)

PGM-FI ( Models) PGM-FI ( 00-0 Models) HOT AT ALL TIMES HOT IN ON OR START FUSE BACK UP, (RADIO).5A FUSE FI E/M 5A C PHOTO UNDER- HOOD FUSE/ RELAY PHOTO FUSE FUEL PUMP (SRS UNIT) 5A page 0-. UNDER- DASH FUSE/ RELAY PHOTO

More information

1 of 12 11/20/2016 9:32 PM

1 of 12 11/20/2016 9:32 PM 1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing

More information

TORQUE SPECIFICATIONS

TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket Bolts Upper Vertical Bolt 16-21 (22-29) Horizontal Bolts 32-43 (43-58) A/C Compressor-To-Bracket Bolts 32-43

More information

Cylinder head, removing and

Cylinder head, removing and Page 1 of 35 15-2 Cylinder head, removing and installing Note: Replace cylinder head bolts. Always replace self-locking nuts, bolts as well as gaskets and O-rings. After installing a replacement cylinder

More information

Motronic September 1998

Motronic September 1998 The Motronic 1.8 engine management system was introduced with the 1992 Volvo 960. The primary difference between this Motronic system and the previous generation of Volvo LH-Jetronic engine management

More information

CYLINDER HEAD GASKET (2AZ-FE)

CYLINDER HEAD GASKET (2AZ-FE) 190 REPLACEMENT 1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See page 111 ) 2. REMOVE FRONT SUSPENSION UPPER BRACE CENTER (W/ FRONT SUSPENSION BRACE UPPER CENTER) 3. REMOVE CHAIN SUBASSY (See page

More information

DISASSEMBLY. Engine. Special Tool(s) Locking Tool, Camshaft Phaser Sprocket Special Tool(s)

DISASSEMBLY. Engine. Special Tool(s) Locking Tool, Camshaft Phaser Sprocket Special Tool(s) 303-01B-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Rear Slinger 303-514 (T95P-6701-AH) Special Tool(s) 303-01B-1 Locking Tool, Camshaft Phaser Sprocket 303-1046 Remover, Crankshaft Rear Seal

More information