ENGINE ASSEMBLY. COMPONENTS (Part 1)
|
|
|
- Arline Simon
- 5 years ago
- Views:
Transcription
1 1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1)
2 2 of 32 COMPONENTS (Part 2)
3 3 of 32 COMPONENTS (Part 3)
4 4 of 32 COMPONENTS (Part 4)
5 5 of 32 COMPONENTS (Part 5)
6 6 of 32 COMPONENTS (Part 6)
7 7 of 32 COMPONENTS (Part 7)
8 8 of 32 COMPONENTS (Part 8)
9 9 of 32 COMPONENTS (Part 9)
10 10 of 32 COMPONENTS (Part 10)
11 11 of 32 COMPONENTS (Part 11) REMOVAL 1. DISCHARGE FUEL SYSTEM PRESSURE 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD 4. REMOVE FRONT WHEELS 5. REMOVE ENGINE UNDER COVER LH 6. REMOVE ENGINE UNDER COVER RH 7. REMOVE FRONT FENDER APRON SEAL RH 8. DRAIN ENGINE OIL 9. DRAIN ENGINE COOLANT 10. DRAIN AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle) 11. DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle) 12. DRAIN BRAKE FLUID (for Manual Transaxle) 13. REMOVE WINDSHIELD WIPER LINK ASSEMBLY 14. REMOVE COWL TOP PANEL OUTER SUB-ASSEMBLY
12 12 of REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (a) Remove the 2 nuts and cover. 16. REMOVE V-RIBBED BELT 17. REMOVE AIR CLEANER INLET ASSEMBLY (a) Remove the 2 bolts, clamp and air cleaner inlet. 18. REMOVE AIR CLEANER CAP SUB-ASSEMBLY
13 13 of REMOVE AIR CLEANER CASE SUB-ASSEMBLY (a) Disconnect the hose clamp. (b) Remove the 3 bolts and air cleaner case. 20. REMOVE BATTERY (a) Loosen the bolt and nut, and remove the battery clamp. (b) Remove the battery and battery tray.
14 14 of REMOVE NO. 2 ENGINE MOUNTING STAY RH (a) Remove the 2 bolts and No. 2 mounting stay RH. 22. REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY (a) Remove the bolt and disconnect the ground cable. (b) Remove the 3 bolts and the engine moving control rod with bracket.
15 15 of REMOVE NO. 2 ENGINE MOUNTING BRACKET RH (a) Remove the 3 bolts and No. 2 mounting bracket RH. 24. DISCONNECT NO. 1 VACUUM HOSE CONNECTOR (a) Remove the clamp and disconnect the vacuum hose connector. 25. DISCONNECT RADIATOR HOSE INLET (a) Remove the clamp and disconnect the radiator hose inlet.
16 16 of DISCONNECT RADIATOR HOSE OUTLET (a) Remove the clamp and disconnect the radiator hose outlet. 27. DISCONNECT OIL COOLER INLET HOSE (for Automatic Transaxle) 28. DISCONNECT OIL COOLER OUTLET HOSE (for Automatic Transaxle) 29. DISCONNECT HEATER INLET WATER HOSE (a) Disconnect the heater inlet water hose. 30. DISCONNECT HEATER OUTLET WATER HOSE (a) Disconnect the heater outlet water hose. 31. REMOVE ECM
17 17 of DISCONNECT ENGINE WIRE (a) Disconnect the engine wire from the engine room relay block. (1) Remove the nut and separate the wire harness. (2) Using a screwdriver, unlock the engine room R/B. Pull the engine room R/B upward. (3) Disconnect the engine wire connectors. (b) Remove the clamp from the bracket.
18 18 of 32 (c) Remove the 2 bolts and clamp from the body. 33. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle) (a) Remove the clip and nut, and separate the control lever. (b) Separate the clamp and separate the cable from the transaxle.
19 19 of DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle) (a) Remove the 2 clips and 2 washers and disconnect the 2 cables from the transaxle. (b) Remove the 2 clips and disconnect the 2 cables from the control cable bracket. 35. DISCONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE (a) Disconnect the No. 1 oil reservoir to pump hose. 36. DISCONNECT RETURN TUBE SUB-ASSEMBLY (a) Disconnect the return tube sub-assembly. 37. REMOVE CLUTCH ACCUMULATOR ASSEMBLY (for Manual Transaxle) 38. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)
20 20 of DISCONNECT FUEL TUBE SUB-ASSEMBLY (a) Remove the No. 1 fuel pipe clamp. (b) Disconnect the connector from the tube while pinching part A with your fingers as shown in the illustration. NOTICE: - Check for contamination in the pipe and around the connector. Clean if necessary and then disconnect the connector. - Disconnect the connector by hand. - Do not bend, fold or rotate the nylon tube. - If the pipe and connector are stuck together, push and pull the connector until it becomes free. - Put the pipe and connector ends in vinyl bags to prevent damage and contamination. 40. REMOVE GENERATOR ASSEMBLY
21 21 of SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (a) Disconnect the connector. (b) Remove the 4 bolts and separate the compressor. HINT: Hang up the hoses instead of detaching them. 42. REMOVE FRONT EXHAUST PIPE ASSEMBLY 43. REMOVE FRONT AXLE HUB NUT LH 44. REMOVE FRONT AXLE HUB NUT RH HINT: Use the same procedures described for the LH side. 45. REMOVE FRONT STABILIZER LINK ASSEMBLY LH 46. REMOVE FRONT STABILIZER LINK ASSEMBLY RH HINT: Use the same procedures described for the LH side. 47. REMOVE FRONT SPEED SENSOR LH 48. REMOVE FRONT SPEED SENSOR RH HINT: Use the same procedures described for the LH side. 49. DISCONNECT TIE ROD ASSEMBLY LH 50. DISCONNECT TIE ROD ASSEMBLY RH HINT: Use the same procedures described for the LH side. 51. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM LH 52. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM RH HINT: Use the same procedures described for the LH side. 53. SEPARATE FRONT AXLE ASSEMBLY LH 54. SEPARATE FRONT AXLE ASSEMBLY RH HINT: Use the same procedures described for the LH side. 55. REMOVE DRIVE PLATE & TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transaxle) 56. REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET (a) Remove the 2 bolts and exhaust pipe support bracket. 57. SEPARATE STEERING SLIDING YOKE 58. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (a) Set the engine lifter. (b) Remove the 4 bolts, 2 nuts and frame side rail plate RH and LH.
22 22 of 32 (c) Remove the 4 bolts, 2 nuts and front suspension member brace rear RH and LH. (d) Carefully remove the engine assembly from the vehicle. (e) Install the 2 engine hangers as shown in the illustration. Parts No. Torque: 38 Nm (387 kgf-cm, 28 ft. lbs.) (f) Using a chain block and an engine sling device, hang the engine assembly.
23 23 of REMOVE VANE PUMP ASSEMBLY (a) Disconnect the oil pressure switch connector. (b) Loosen the 2 bolts and remove the vane pump from the engine. 60. REMOVE FRONT FRAME ASSEMBLY (a) A/T: Remove the nut from the engine mounting insulator LH. (b) M/T: Remove the bolt from the engine mounting insulator LH.
24 24 of 32 (c) Remove the nut from the engine mounting insulator RH. (d) Remove the bolt from the engine mounting insulator FR. (e) M/T: Remove the bolt from the engine lateral control rod. (f) Raise the engine assembly and separate the front frame. 61. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH 62. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH 63. REMOVE ENGINE WIRE 64. REMOVE STARTER ASSEMBLY (for Manual Transaxle) 65. REMOVE STARTER ASSEMBLY (for Automatic Transaxle)
25 25 of SEPARATE AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle) 67. SEPARATE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle) 68. REMOVE DRIVE PLATE & RING GEAR SUB-ASSEMBLY (for Automatic Transaxle) 69. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle) 70. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle) 71. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle) 72. INSTALL ENGINE STAND (a) Fix the engine onto a engine stand with the bolts. 73. REMOVE FUEL DELIVERY PIPE WITH INJECTOR 74. REMOVE INTAKE MANIFOLD (a) Remove the 5 bolts, 2 nuts, and intake manifold. (b) Remove the gasket from the intake manifold. 75. REMOVE INTAKE AIR CONTROL VALVE (for PZEV) 76. REMOVE NO. 2 VENTILATION HOSE
26 26 of REMOVE NO. 1 INTAKE MANIFOLD INSULATOR (a) Remove the intake manifold insulator from the cylinder block. 78. REMOVE DRIVE SHAFT BEARING BRACKET (a) Remove the 3 bolts and drive shaft bearing bracket 79. REMOVE OIL LEVEL GAUGE SUB-ASSEMBLY 80. REMOVE OIL LEVEL GAUGE GUIDE (a) Remove the bolt and oil level gauge guide. (b) Remove the O-ring from the oil level gauge guide.
27 27 of REMOVE MANIFOLD STAY (a) Remove the bolt, nut and stay. 82. REMOVE NO. 2 MANIFOLD STAY (a) Remove the bolt, nut and stay. 83. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (a) For PZEV: (1) Disconnect the air-fuel ratio sensor connector. (2) Remove the 5 nuts, manifold converter and gasket.
28 28 of 32 (b) Except for PZEV: (1) Remove the 4 bolts and No. 1 insulator. (2) Disconnect the air-fuel ratio sensor connector. (3) Remove the 5 nuts, manifold converter and gasket. 84. REMOVE WATER INLET 85. REMOVE THERMOSTAT
29 29 of REMOVE NO. 1 WATER BY-PASS PIPE (a) Remove the bolt, 2 nuts and No. 1 water by-pass pipe with the gasket. 87. REMOVE OIL COOLER PIPE (w/ Oil Cooler) (a) Remove the bolt, 2 nuts and oil cooler pipe with the gasket.
30 30 of REMOVE ENGINE MOUNTING BRACKET RH (a) Remove the 3 bolts and engine mounting bracket RH. 89. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY (a) Remove the bolt, nut and belt tensioner. 90. REMOVE IGNITION COIL ASSEMBLY (a) Remove the 4 bolts and 4 ignition coils. 91. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY 92. REMOVE KNOCK SENSOR (a) Disconnect the sensor connector. (b) Remove the nut and sensor.
31 31 of REMOVE RADIO SETTING CONDENSER (a) Remove the bolt and radio setting condenser. 94. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY (a) Using a 24 mm deep socket wrench, remove the engine oil pressure switch assembly.
32 32 of REMOVE ENGINE COOLANT TEMPERATURE SENSOR (a) Using SST, remove the sensor and gasket. SST ALLDATA, LLC. All Rights Reserved. (Version )
PARTIAL ENGINE ASSY (2ZZ GE)
COMPONENTS 14189 140R701 7.0 (71, 62 in. lbf) Cylinder Head Cover No. 2 19 (194, 14) Radiator Support Upper 19 (194, 14) Radiator Hose Inlet Cruise Control Actuator Assy 6.0 (61, 53 in. lbf) Radiator Assy
EM 92 2TR-FE ENGINE MECHANICAL ENGINE ASSEMBLY REMOVAL
92 2TR-FE ENGINE MECHANICAL ENGINE ASSBLY ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE ( FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for Pre Runner and 4WD Type) (a) Remove the
PARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque
ENGINE MECHANICAL 1417 COMPONENTS 141FP01 Radiator Grille Front Bumper Cover Engine Under Cover RH Engine Under Cover LH A79361 962 1418 ENGINE MECHANICAL Heater Outlet Water Hose 7.0 (71, 62 in. lbf)
EM 97 2TR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSTALLATION
2TR-FE ENGINE MECHANICAL ENGINE ASSBLY 97 G038557E01 INSTALLATION 1. INSTALL ENGINE OIL PRESSURE SWITCH ASSBLY ( LU-1) 2. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH (a) Install the engine mounting
3/13/ :32 AM. NOTICE: Do not disconnect the hose.
1 of 25 REPLACEMENT 1. REMOVE HOOD SUB-ASSEMBLY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FRONT FENDER APRON SEAL RH 6. DRAIN ENGINE OIL a. Install
PARTIAL ENGINE ASSY (2TR FE)
COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER
2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI - Removal and Installation
Page 1 of 8 Removal and Installation REMOVAL 1. REMOVE HOOD Torque: 13 Nm (130 kgf-cm, 9 ft. lbs.) 2. REMOVE BATTERY 3. REMOVE ECM AND ECM CASE Torque: 6.9 Nm (70 kgf-cm, 61 inch lbs.) 4. REMOVE ECM BRACKET
EM 112 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSPECTION. Intake Air Surge Tank Side
112 Intake Air Surge Tank Side Cylinder Head Side 1GR-FE ENGINE MECHANICAL ENGINE ASSBLY INSPECTION 1. INSPECT INTAKE MANIFOLD FOR WARPAGE (a) Using a precision straight edge and feeler gauge, measure
REMOVAL AND INSTALLATION OF TRANSAXLE (4WD)
MT63 REMOVAL AND INSTALLATION OF TRANSAXLE (4WD) REMOVAL AND INSTALLATION OF TRANSAXLE REMOVE AND INSTALL TRANSAXLE AS SHOWN MT64 REMOVAL OF TRANSAXLE 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY
ENGINE ASSEMBLY COMPONENTS EM 170 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY V-BANK COVER VACUUM HOSE AIR CLEANER ASSEMBLY NO. 2 VENTILATION HOSE
170 ENGINE 1GR-FE MECHANICAL COMPONENTS 1GR-FE ENGINE MECHANICAL ENGINE 7.5 (76, 66 in.*lbf) V-BANK COVER 8.0 (82, 71 in.*lbf) 8.0 (82, 71 in.*lbf) VACUUM HOSE AIR CLEANER NO. 2 VENTILATION HOSE MASS AIR
FUEL SYSTEM PRECAUTION FU 1
2GR-FE EL EL SYSTEM EL SYSTEM PRECAUTION 1 1. EXPRESSIONS OF IGNITION SWITCH (a) The type of the ignition switch used on this model differs according to the specifications of the vehicle. The expressions
REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH. 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N.
REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N. (b) Check that the parking brake is released. (c) Remove
CYLINDER HEAD (for Bank 2 4WD and Pre-Runner)
144 1GR-FE ENGINE MECHANICAL CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) ENGINE 1GR-FE ENGINE MECHANICAL COMPONENTS 88 (897, 65) x4 88 (897, 65) x4 NO. 1
Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.
Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE
VALVE CLEARANCE (3MZ-FE)
ENGE MECHANICAL ADJUSTMENT. DRA ENGE COOLANT (See page ). REMOVE FR WIPER ARM LH (See page 7 ). REMOVE FR WIPER ARM RH (See page 7 ) 4. REMOVE COWL TOP VENTILATOR LOUVER SUBASSY (See page 7 ). REMOVE WDSHIELD
REPLACEMENT. 9. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 (a) Remove the 2 bolts and control cable bracket No.1.
AUTOMATIC TRANSMISSION / TRANS REPLACEMENT 1. REMOVE HOOD SUBASSY 2. REMOVE BATTERY 3. REMOVE WINDSHIELD WIPER LINK ASSY (See page 666) 4. REMOVE FRONT PANEL ASSY (See page 2610) 5. REMOVE CYLINDER HEAD
REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration.
21 ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE (See page FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for 4WD and Pre-Runner) (a) Remove the 4 bolts, then remove the No. 1 engine
REPLACEMENT. 12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 5 bolts, the engine moving control rod and the engine mounting stay.
1484 ENGINE MECHANICAL REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT WIPER ARM HEAD CAP 3. REMOVE FR WIPER ARM RH (See page 668 ) 4. REMOVE FR WIPER ARM LH (See page 668 ) 5. REMOVE COWL TOP VENTILATOR
1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
Fastener Tightening Specifications Specification
2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt
CYLINDER HEAD GASKET (2AZ-FE)
190 REPLACEMENT 1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See page 111 ) 2. REMOVE FRONT SUSPENSION UPPER BRACE CENTER (W/ FRONT SUSPENSION BRACE UPPER CENTER) 3. REMOVE CHAIN SUBASSY (See page
COMPONENTS ILLUSTRATION
COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION REMOVAL 1. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (a) Remove the windshield wiper motor and link assembly. 2. REMOVE COWL BODY MOUNTING REINFORCEMENT
REMOVAL. 10. REMOVE FRONT SUSPENSION MEMBER BRACE Remove the 8 bolts and brace.
EM64 ENGINE MECHANICAL (2JZGE) EM1S801 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DRAIN ENGINE OIL 4. REMOVE ENGINE COVER Remove the 4 nuts and engine cover. 5. REMOVE AIR CLEANER
2013 Kia Optima L4-2.0L Turbo
1 of 13 5/29/2016 11:34 AM 2013 Kia Optima L4-2.0L Turbo Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement Removal CAUTION: Use fender covers to avoid damaging painted
OIL PUMP (for 4WD and Pre-Runner)
1GR-FE BRICATION OIL PUMP (for 4WD and Pre-Runner) OIL PUMP (for 4WD and Pre-Runner) ENGINE 1GR-FE BRICATION COMPONENTS 23 88 (897, 65) 88 (897, 65) NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY FRONT PROPELLER
REPLACEMENT HINT: 11. REMOVE V RIBBED BELT TENSIONER ASSY (a) Remove the 5 bolts and V ribbed belt tensioner.
14142 REPLACEMENT HINT: ENGINE MECHANICAL Refer to CAMSHAFT (RH BANK) or CAMSHAFT (LH BANK) for the replacement procedure of the No.2 chain (see page 14157 or 14175). 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
REMOVAL EM SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System) (a) Remove the bolt shown in the illustration.
21 ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE (See page FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for 4WD and Pre-Runner) (a) Remove the 4 bolts, then remove the No. 1 engine
CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT
REPLACEMENT N0. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE ). REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE ). REMOVE STARTER ASSY (SEE PAGE 99). REMOVE AUTOMATIC TRANSAXLE ASSY (SEE PAGE
Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC
Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC Engine Mechanical System Camshaft sprocket bolt 90 ~ 110 900 ~ 1,100 65 ~ 80 Cylinder head cover bolt 8 ~ 10 80 ~ 100 5.8 ~ 7.2 Main bearing
Supercharged MK1 MR2 Part Diagrams
Supercharged MK1 MR2 Part Diagrams Created by: Charles K. (ckowalc) 1 Table of Contents PART DIAGRAM PAGE ACCELERATOR LINK 9 AIR CLEANER 10 AIR CLEANER 4AGZE 11 ALTERNATOR 4AGZE 12 ANTENNA 13 ARMREST &
2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head
Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat
IG 1 2GR-FE IGNITION IGNITION SYSTEM IGNITION SYSTEM ECM ENGINE ROOM R/B - IG2 FUSE - ST/AM FUSE IGNITION COIL NOISE FILTER NOISE FILTER A137458E01
NITION SYSTEM ENGINE 2GR-FE PARTS LOCATION 2GR-FE NITION NITION SYSTEM 1 ECM ENGINE ROOM R/B - 2 FUSE NITION COIL - ST/AM FUSE NOISE FILTER NOISE FILTER A137458E01 2 2GR-FE NITION NITION SYSTEM SYSTEM
VALVE CLEARANCE (1NZ-FXE)
146 ENGINE MECHANICAL ADJUSTMENT 1. REMOVE REAR FLOOR BOARD NO.2 (See page 211 16) 2. REMOVE DECK FLOOR BOX REAR (See page 211 16) 3. REMOVE REAR FLOOR BOARD NO.3 (See page 211 16) 4. DISCONNECT BATTERY
12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 4 bolts, the engine moving control rod and the bracket.
TIMING BELT (3MZFE) REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FR WIPER ARM RH (See page 669) 3. REMOVE FR WIPER ARM LH (See page 669) 4. REMOVE COWL TOP VENTILATOR LOUVER SUBASSY (See page 669) 5.
Zoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM WS002X
Last Modified: 4-26-2007 Service Category: Engine/Hybrid System 1.6 A Section: Engine Mechanical Model Year: 2007 Model: 4Runner Doc ID: RM0000029WS002X Title: 1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION
303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine
2010 MKZ Report a problem with this article 303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid REMOVAL Procedure revision date: 10/19/2012 Engine Special Tool(s) 2,200# Floor Crane,
2004 Toyota CAMRY. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS
2004 Toyota CAMRY Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS REPLACEMENT 1. REMOVE HOOD SU-ASSY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER
1 of 12 8/18/ :52 AM
1 of 12 8/18/2016 11:52 AM REMOVAL 1. DISCHARGE FUEL SYSTEM PRESSURE a. Discharge fuel system pressure. 2. REMOVE DECK BOARD SUB-ASSEMBLY a. Disengage the 5 clips and turn up the front side of the deck
REMOVAL FU 11 2TR-FE FUEL FUEL INJECTOR. Pinch. Checker. Detaching Switch Pull Out. Retainer. Fuel Hose Connector. Pipe. O-ring. Pinch.
2TR-FE EL EL INJECTOR 11 REMOVAL 1. DISCHARGE EL SYSTEM PRESSURE (See page -1) 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 3. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY NO.1 4. DRAIN ENGINE COOLANT
10. SEPARATE COMPRESSOR (a) Remove the nut, 3 bolts compressor stay and compressor. HINT: Hang up the hoses instead of detaching.
14108 ENGINE MECHANICAL REPLACEMENT 1. DRAIN ENGINE COOLANT(See page165 ) 2. SEPARATE BATTERY NEGATIVE TERMINAL 3. REMOVE VBANK COVER SUBASSY (a) Remove the 2 cap nuts and Vbank cover subassy. 4. REMOVE
1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
Engine Removal/Installation
Engine Removal/Installation Make sure jacks and safety stands are placed properly and hoist brackets are attached to correct positions on the engine. (See Section 1). Apply parking brake and block rear
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual REMOVAL Procedure revision date: 07/25/2008 Engine Special Tool(s) Heavy Duty Floor Crane 014-00071 or equivalent Lifting Bracket, Engine
2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA Page 1
2003 Toyota Truck Highlander 2WD V6-3.0L (1MZ-FE) Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT FENDER APRON SEAL
REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide.
EM34 ENGINE MECHANICAL (2RZFE, 3RZFE) P23426 EM1MY01 REMOVAL 1. DRAIN ENGINE COOLANT 2. DISCONNECT THESE CABLES: (a) Disconnect the accelerator cable from the throttle body. A/T: Disconnect the throttle
Disconnect negative battery cable and remove coolant bottle cap.
1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use
Lower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly
Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie
Page 1 of 6 Section 07-01A: Transaxle, Automatic CD4E 1996 Probe Workshop Manual REMOVAL Procedure revision date: 06/14/2000 Transaxle Item Part Number Description 1 10655 Battery 2 10732 Battery Tray
10/13/2016 5:33 PM. Radiator (B205L/R, B235R) To remove
1 of 15 Radiator (B205L/R, B235R) To remove 1. Disconnect the vent hose from the battery. Disconnect the positive and negative battery cables and remove the battery. Note the radio code where applicable.
2/17/2017 Timing Belt Service and Repair, Removal and Replacement
http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com 1/22 http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com
2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)
1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15
COMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
Page 1 of 44 REPLACEMENT 1. 2. 3. 4. REMOVE ENGINE UNDER COVER RH DRAIN COOLANT (See REPLACEMENT ) REMOVE FRONT WHEEL RH REMOVE CYLINDER HEAD COVER NO. 2 a. Remove the 2 nuts, 2 clips and cylinder head
STARTER COMPONENTS FOR REMOVAL AND INSTALLATION
Removal STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Starter Components For Removal And Installation REMOVAL OF STARTER 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started
ADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT
Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. ADJUSTMENTS VALVE CLEARANCE ADJUSTMENT 1. No valve clearance adjustment is required, as hydraulic valve lash adjusters are used.
1 of 12 11/20/2016 9:32 PM
1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing
03 1 SERVICE SPECIFICATIONS
SERVICE SPECIFICATIONS STANDARD BOLT STANDARD BOLT HOW TO DETERMINE BOLT STRENGTH 031 0307K02 Bolt Type Hexagon Head Bolt Normal Recess Bolt Deep Recess Bolt Stud Bolt Weld Bolt Class 4 4T No Mark No Mark
SUPERCHARGER. ON-VEHICLE INSPECTION 1. INSPECT SUPERCHARGER OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick.
EG45 ONVEHICLE INSPECTION 1. INSPECT OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick. (a) Park the vehicle on a level spot and turn the engine off. (b) 4WD: Remove the LH front
REMOVAL. Fig Sized for Print
ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting
11. REMOVE OIL PAN SUB ASSY NO.2 (a) Remove the 18 bolts and 2 nuts.
1444 ENGINE MECHANICAL REPLACEMENT 1. REMOVE ENGINE ASSEMBLY (SEE PAGE 1419) 2. REMOVE DRIVE PLATE & RING GEAR SUBASSY (AUTOMATIC TRANSMISSION) (SEE PAGE 1419) SST 0921354015 (9165160855), 0933000021 3.
1999 F-150/250 Workshop Manual
Page 1 of 8 SECTION 303-01B: Engine 4.6L and 5.4L IN-VEHICLE REPAIR Procedure revision date: 02/03/1999 Intake Manifold Lightning Removal WARNING: Do not smoke or carry lighted tobacco or open flame of
1992 Toyota Cressida
Monday, May 16, 2016 5:32:47 PM Page 13 2005 Mitchell Repair Information Company, LLC. Fig. 7: Exploded View Of Typical Cylinder Head & Components Fig. 8: Cylinder Head Bolt Removal Sequence Monday, May
This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.
Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers
3/15/2015 1:10 PM TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC]
![3/15/2015 1:10 PM TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC]](/thumbs/93/113245190.jpg "3/15/2015 1:10 PM TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC]")
1 of 17 TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1. Disconnect the negative battery cable. 2. Remove the under cover. 3. Remove the front wheels and tires (RH). 4. Remove the splash shield. 5. Remove
Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components
Page 1 of 25 Service and Repair REMOVAL Related Components Page 2 of 25 1ZZ-FE Page 3 of 25 2ZZ-GE 1. REMOVE UPPER FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL 2. DRAIN ENGINE COOLANT 3. REMOVE
COOLING SYSTEM ON-VEHICLE INSPECTION CO 1
Radiator Cap Tester 2AZ-FE OLING OLING SYSTEM A112194E01 A112306 OLING SYSTEM ON-VEHICLE INSPECTION 1 1. CHECK OLING SYSTEM FOR LEAKS (a) Remove the radiator reservoir cap. CAUTION: To avoid the danger
1999 E-Series Workshop Manual
http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998
7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).
1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual
Ford 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.
1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T
2013 Mustang Workshop Manual
32. Attach the wiring harness retainers to the LH side of the oil pan and the front oil pan stud bolts and install the 2 nuts. Tighten to 8 Nm (71 lb-in). 33. Position the underbody shield and install
Toothed belt, removing and installing
Toothed belt, removing and installing Special Tools and Equipment ^ 3212 spanner wrench ^ 3387 pin wrench ^ T40011 pin ^ T40026 locking pin ^ T40028 socket ^ T40030 camshaft adjuster gauge Removing Lock
ALLDATA Online Toyota Camry L4-2.4L (2AZ-FE) - Rear Strut Assembly. Rear Strut Assembly
Page 1 of 11 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2004 Toyota Camry L4-2.4L (2AZ-FE) Conversion Calculator Vehicle
2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar
COWL TOP VENT PANEL 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top
DISASSEMBLY AND REASSEMBLY
24 01 DISASSEMBLY AND REASSEMBLY COMPONENTS AND SPECIAL TOOLS Injector Puller Y99220072B Glow Plug Wrench Y99220132B Fuel Pipe Wrench Sealing Caps 665 995 5844 Injector Copper Washer Puller Y99220022B
TIMING CHAIN COMPONENTS
Page 1 of 30 TIMING CHAIN COMPONENTS Fig. 46: Identifying Camshaft Timing Oil Control Valve Assembly Components With Torque Page 2 of 30 Specifications (1 Of 3) Fig. 47: Identifying Camshaft Timing Oil
DESCRIPTION AND OPERATION
303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589
Torque Guidelines (Z 22 SE)
Page 1 of 14 Torque Guidelines (Z 22 SE) No. Designation Nm 1 Retaining bolts, coolant pump sprocket to coolant pump 2 Retaining bolts, balancer shaft timing chain guide rail to 3 Retaining bolts, balancer
CLUTCH Toyota Celica DESCRIPTION ADJUSTMENTS CLUTCH PEDAL HEIGHT Clutch. Celica
CLUTCH 1993 Toyota Celica 1993 Clutch Celica DESCRIPTION The single, dry disc type clutch uses a hydraulically operated master cylinder and a release cylinder mounted on clutch housing. Clutch release
2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing
1 of 25 8/18/2011 6:10 PM 2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing Cylinder head/gasket, replacement
2001 Lincoln LS Workshop Manual
Page 1 of 10 SECTION 303-01B: Engine 3.9L 2001 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/16/2000 Intake Manifold Removal 1. Disconnect the battery ground cable. For additional
Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.
ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.
1 of 11 7/11/2015 6:48 AM
1 of 11 7/11/2015 6:48 AM 43. Disconnect the A/C pressure sensor. 44. Disconnect the A/C discharge hose from the compressor and secure to the cooling fan assembly. 45. Disconnect the A/C suction hose from
REMOVAL 7. DISCONNECT ACCELERATOR CABLE FROM THROTTLE BODY. 8. DISCONNECT HOSES (a) Remove the 2 bolts from the air intake chamber assembly.
ENGINE MECHANICAL (VZFE) EM9 REMOVAL EM1MP01 1. REMOVE ENGINE UNDER COVER. DRAIN ENGINE COOLANT. REMOVE FRONT EXHAUST PIPE (See page EM10 ). DISCONNECT HEATER HOSE. REMOVE AIR CLEANER ASSEMBLY 6. REMOVE
Timing Belt: Service and Repair. Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002
Timing Belt: Service and Repair Toyota Truck Sienna LE V6-3.0L (1MZ-FE) 2002 REMOVAL 1. REMOVE OUTER FR COWL TOP PANEL ASSEMBLY 2. REMOVE RH FRONT WHEEL 3. REMOVE RH FENDER APRON SEAL 4. REMOVE GENERATOR
10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L
2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN
COMPONENT LOCATIONS GROUP CONTENTS FUSIBLE LINK, FUSE AND IOD OR STORAGE CONNECTOR RELAY OTHER DEVICES...
70-1 GROUP 70 COMPONENT LOCTIONS CONTENTS RELY........................ 70-2 OTHER DEVICES............... 70-3 CONTROL UNIT................. 70-4 INSPECTION TERMINL......... 70-7 SENSOR.......................
9. Engine Assembly ENGINE ASSEMBLY
9. Engine Assembly A: REMOVAL 1) Set the vehicle on a lift. 2) Open the front hood fully, and then support with the hood stay. 3) Collect the refrigerant from A/C system. 4) Release the fuel pressure.
EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION
EG18 ENGINE TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG5EK01 ENGINE EG19 EG20 ENGINE ENGINE EG21 EG22 ENGINE TIMING BELT REMOVAL EG5G101 1. REMOVE OIL PAN PROTECTOR 2. REMOVE ENGINE UNDER COVER
Cylinder Head Assembly: Removal and Replacement Repair Procedures
2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA 10.52 Page 1 Cylinder Head Assembly: Removal and Replacement Repair Procedures COMPONENT 2007 Kia Rio L4-1.6L Copyright 2013, ALLDATA 10.52 Page 2 REMOVAL Engine
2002 Explorer Sport/Sport Trac Workshop Manual
Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)
2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE)
2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair TIMING CHAIN TIMING CHAIN http://alldatapro.com/alldata/pro~v440713400~c39519~r0~od~n/0/108596970/110859775/110859788/110859790/34853741/100411974/34853743/56492475
DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.
303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773
LINCOLN. Continental 1
3154_U01.qxd 8/1/03 7:28 AM Page 1 Continental 1 BRAKES...1-27 DRIVE TRAIN...1-21 ENGINE REPAIR...1-7 FUEL SYSTEM...1-20 PRECAUTIONS...1-7 SPECIFICATION CHARTS...1-2 STEERING AND SUSPENSION...1-22 A Air
COOLING SYSTEM ON-VEHICLE INSPECTION CO 1
2GR-FE OLING OLING SYSTEM A133894 OLING SYSTEM ON-VEHICLE INSPECTION 1 1. CHECK FOR ENGINE OLANT LEAKS CAUTION: Do not remove the radiator cap while the engine and radiator are still hot. Pressurized,
2006 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE)
ALLDATA Repair - 2006 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) - Service and R... Page 1 of 12 2006 Toyota Truck Tundra 4WD V8-4.7L (2UZ-FE) Vehicle» Powertrain Management» Fuel Delivery and Air Induction»
1991 Volkswagen Vanagon Syncro
corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
1992 Clutch. Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT
Article Text ARTICLE BEGINNING 1992 Clutch Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT DESCRIPTION All clutches are single disc type. Pressure plate assembly uses a diaphragm spring to engage