With over 100 different standard configurations... And still growing! Remember to use COPASLIP anti-seize compound on all insert screws

Transcription

1 With over 100 different standard configurations And still growing! Standard Length End Mills TXD TXD TXD TXD F TXD TXD TXD F TXP TXP TXP TXP TXP TXP F TXP EM Standard Length End Mills with Coolant Through TXD C TXD C TXD C TXD FC TXD C TXD C TXD C TXD FC TXD C TXD C TXP C TXP C TXP C TXP C TXP C TXP FC TXP EMC

2 Extended Length End Mills TXD XL TXP L TXP XL TXP L TXP L Extended Length End Mills with Coolant Through TXD XLC TXD XLC TXD LC TXD XLC TXD XXLC TXD XXLC TXP LC TXP XXLC TXP LC TXP XLC TXP XXLC TXP LC TXP XLC TXP XXLC TXP XXLC TXP LC TXP XLC TXP XXLC TXP XXLC

3 Featuring: Cylindrical Shanks Coolant through Extra long shanks Specifically designed for: Milling Chucks Hydraulic Chucks Shrink-fit Systems Standard Length Cylindrical Shank End Mills with Coolant Through TXD90CY-0625C TXD90CY-0750C TXD90CY C TXP90CY C TXP90CY C TXP90CY C Extended Length Cylindrical Shank End Mills with Coolant Through TXD90CY-0625-XXLC TXD90CY-0750-XXLC TXD90CY XXLC TXP90CY XXLC TXP90CY XXLC TXP90CY XXLC

4 R-8 Shank End Mills Designation d¹ Shank l¹ l² Max. ap flutes Insert Insert Screw Wrench TXP R R TXP R R TXP R R Screw-On Milling Cutters Designation d¹ d¹ mm g l¹ Max. ap flutes Insert Insert Screw Wrench TXD TS M TXD TS M TXD TS M TXD TS M TXD TS M TXD TS M TXP TS M TXP TS M TXP TS M TXP TS M TXP TS M TXP TS M TXP TS M TXP TS M

5 Standard Series Face Mills Designation d¹ d² h Max. ap flutes lbs. Insert Insert Screw Wrench TXD SM TXD TXP SM TXP TXP F TXP TXP TXP TXP F TXP TXP TXP F TXP * *Cutter supplied with 4 holes on a 4" bolt circle Standard Series Face Mills with Coolant Through Designation d¹ d² h Max. ap flutes lbs. Insert Insert Screw Wrench TXD SM-MC TXD MC TXP SM-MC TXP MC TXP F-MC TXP MC TXP MC TXP MC *Cutter supplied with 4 holes on a 4" bolt circle

6 Featuring: Specifically designed for aluminum machining Allows for full depths of cut and wider widths of cut Optimized speeds and feeds while lowering horsepower consumption Coarse Pitch Face Mills Designation d¹ d² h Max. ap flutes lbs. Insert Insert Screw Wrench Through Coolant Enabled TXP AL-3-MC TXP AL-3-MC TXP AL-3-MC TXP AL-4XMC Standard Non-Through coolant TXP AL TXP AL TXP AL

7 Inserts for - / THX90 Inserts with optimized geometries and large selection of radii from 1/32" - 5/32" for steel, cast steel and aluminum alloys. Very effective with high metal removal rates in medium and heavy duty milling. / 600 / 610 / 574 / THX90 Inserts TN7525 TN6525 TN7535 TN6540 TN450 TN5515 TN6510 TN6520 TN2510 TTM TTR THM THR THM-U TTI-25 Designation l s r d d¹ bs a Coated Uncoated Cermet.635 3/16 3/64 3/ n n n n n n n n.381 1/8 1/32 1/ n n n n n n n n n /16 1/32 3/ n n n n n n n n n 3/ n n n n n n n n n n n n n n / n n n n n n n (2) 5/ n n n n (2) 3/ n n n n (2) 1/ n n n n (2) 5/ n n n n n (3).635 3/16 3/64 3/ n n n n n n n n.634 3/ n n n n n n n n n.634 3/ n n n n n n n n n / THX90 Alu. Inserts TN7525 TN6525 TN7535 TN6540 TN450 TN5515 TN2510 TN6501 TN6502 TTM TTR THM THR THM-U TTI-25 Designation l s r d d¹ bs a Coated Uncoated Cermet (1)*.381 1/8 1/ n (1)* / n n (1)* 3/ n n (1)* 1/ n n (1,2)* 5/ n (1,2)* 3/ n (1,2)* 1/ n (1,2)* 5/ n (1)* / n n (1)* 1/ n n (1)* 3/ n n Note 1: Note 2: Note 3: Due to the higher side rake angles, - 522, & inserts are wider and will cut oversize. To provide necessary clearance for the inserts with radii over 5/64", the cutter body must be relieved. Cutting edges are serrated and marked I & II, are to be mounted alternating edge I & II, and can only be used with a minimum of 2 teeth. Best results achieved when used in cutters with an even number of flutes. * Optimized for aluminum.