INSTALL GUIDE FLC-IDS(RS)-BZ4-[FLRSBZ4]-EN

Transcription

1 INSTLL GUIDE DOCUMENT NUMBER 3585 REVISION DTE 74 FIRMWRE FLC-IDS(RS)-BZ4-[FLRSBZ4] HRDWRE FLRSBZ4 ESSORIES FLPROG (REQUIRED) FLRF//4 (OPTIONL) CRLINK SCL (OPTIONL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. BEFORE INSTLLTION - Connect module to computer - Login to Weblink account 3- Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately)

2 PGE OF 3 DOC.: # VEHICLE LIST - OF FETURES YER 3X LOCK /STNDLONE MOD. SECURE TKEOVER DT IMMOBILIZER BYPSS RM OEM LRM DISRM OEM LRM DOOR LOCK DOOR UNLOCK TRUNK/HTCH RELESE PRKING LIGHT CTRL RP SHUTDOWN CTRL TCHOMETER STTUS MONITORING BRKE PEDL STTUS MONITORING VSS STTUS MONITORING GLOW PLUG STTUS MONITORING DOOR STTUS MONITORING TRUNK STTUS MONITORING HOOD STTUS MONITORING* B-Class T -4 CL-Class T 4 G-Class T** 3 G-Class MG T** 3 GL-Class T** 3 GL-Class PTS T** 3 GL-Class Diesel T** 3 GL-Class PTS Diesel T** 3 GL-Class MG T** 3 GL-Class MG PTS T** 3 ML-Class T** -3 ML-Class PTS T** -3 ML-Class Diesel T** -3 ML-Class PTS Diesel T** -3 ML-Class MG T** -3-3 MERCEDES-BENZ ML-Class MG PTS T** * If equipped with a factory hood switch. ** 4 models are NOT covered. The encryption is not the same. Verify VIN before installation. INSTLL TYPE MKE II ll the covered Push To Start (PTS) vehicles are equipped with a keyless authorization system called "Keyless Go". POWER LIFTGTE MODEL NOTES I This firmware covers utomatic Transmission (T) vehicles only.

3 PGE 3 OF 3 DOC.: # BOX CONTENTS - OF BOX CONTENTS MODULE LED LED PROGRMMING BUTTON USB BLCK BLCK BLCK BLUE BLCK EXPNSION PCK BLCK XP LED 3 4 RED BLUE 4 3 BLCK 4 3 BLUE TELEMTIC PORT PIN BLCK CONNECTOR WHITE BLCK PIN WHITE CONNECTOR T-HRNESS 4 3 FTERMRKET HOOD SWITCH ND CBLE 4 PIN BLUE CONNECTOR - TELEMTIC CBLE THE FLHRNTM CBLE IS INCLUDED IN KITS MNUFCTURED FTER 0//3. CONTCT YOUR UTHORIZED DELER, IF THIS CBLE IS NOT INCLUDED. PIN BLCK CONNECTOR FLHRNTM PIN BLCK CONNECTOR BLCK RF PORT/WEBLINK PORT EXPNSION PCK SSEMBLY XP LED EXTR CONNECTOR HOUSING LED 3 4 LED STICKER TOP VIEW BOTTOM VIEW STICKER TOP VIEW WHITE WEBLINK CBLE (required accessory sold separately) WEBLINK CBLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLCK CBLE

4 PGE 4 OF 3 DOC.: # COMPTIBLE ESSORIES - OF RF KIT (accessories sold separately) FLRF//4 RF KIT (NC) MODULE RF PORT NTENN TELEMTIC KIT (accessories sold separately) CRLINK FLHRNTM MODULE TELEMTIC PORT (NC) WRNING: The Car Connection Pro telematic kit is NOT compatible with this product.

5 TECHNICL NOTE - OF IMPORTNT PGE 5 OF 3 DOC.: # INSTLL VIDEO GLLERY VILBLE ONLINE Before installing this product, consult our Install Video Gallery and watch: Vehicle Disassembly Procedure videos Module Connection Procedures videos Module Programming Procedures videos Æ To access the videos, simply log in your Weblink user account, and click on "Install videos" under the "Support" tab. Æ Then, select a vehicle make, year and model to display the available videos.

6 PGE 6 OF 3 DOC.: # COMPONENT LOCTOR - OF INTERIOR VIEW DRIVER SIDE VIEW PSSENGER SIDE VIEW B

7 PGE 7 OF 3 DOC.: # MODULE INSTLLTION PROCEDURE - OF ON ON the vehicle. Verify all vehicle functionalities. If the vehicle displays error messages or any malfunction: stop the installation and service the vehicle. 07 Turn the vehicle. 08 ENGINE STOP ON WRNING: ny vehicle harness that is disconnected during installation, must be re-connected before performing any system tests. Failure to comply will result in vehicle displaying error messages. n OEM scantool will be required to clear the error messages. 3 If the vehicle is not equipped with a factory hood switch, install an aftermarket hood switch as shown in STEP 4 of the WIRING DIGRM. the vehicle. Verify all vehicle functionalities. 4 If required, connect a compatible RF Kit to the RF port of the module. RF ENGINE STOP ENGINE STOP Verify all keyfob functionalities (Door Lock, Door Unlock, Trunk Release and RFID access if equipped). 09 Insert the expansion pack in the module. 0 WRNING: If the vehicle displays error messages or any malfunction, stop the installation, verify every connection and if the problem persists, call technical support. 5 If required, connect a compatible Telematics Device to the TELEMTIC port of the module. Turn the vehicle. 6 Put sticker on a clean and visible surface in the engine bay and put sticker under the dashboard near the OBDII connector. 7 Module installation procedure completed. ON ENGINE STOP Connect the module to the computer with the programming cable (WEBLINK port). Flash the module with the latest firmware then flash the expansion pack. Connect every connector to the module, as shown in STEP of the WIRING DIGRM. 06 Connect and secure every connector to the vehicle, as shown in STEP of the WIRING DIGRM. Connect every other connector to the module, as shown in STEP 3 of the WIRING DIGRM.

8 PGE 8 OF 3 DOC.: # TYPE - WIRING DIGRM - OF WRNING STEP -TO CONNECT THE MODULE: FOLLOW STEPS TO 4 -TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO CONNECT TO VEHICLE VEHICLE WITH OEM KEYFOB TO TEST CONNECTIONS BLCK 8 PIN B (VEHICLE HRNESS) MODULE STEP CONNECT TO MODULE IGNITION SWITCH BLCK 8 PIN BLCK 0 PIN RELY STEP 3 B BLCK PIN CONNECT TO MODULE BLUE 6 PIN BLCK PIN (VEHICLE HRNESS) WHITE PIN BLCK PIN (NOT USED) STEP 4 CONNECT IF REQUIRED WHITE 0 PIN IF NOT EQUIPPED WITH N OEM HOOD SWITCH, INSTLL N FTERMRKET HOOD SWITCH HOOD SWITCH 07 GRY/WHITE - HOOD STTUS (-) INPUT 08 GRY/BLCK (NOT USED)

9 ML-Class PTS T ML-Class PTS Diesel T -3-3 MODULE LOCTION -3 POLRITY ML-Class MG PTS T WIRE COLOR 3 CanH 0 pin Brown/Red Keyless GO Module, under body panel beside rear left seat. B CanL 0 pin Brown Keyless GO Module, under body panel beside rear left seat. B POSITION GL-Class PTS Diesel T CONNECTOR TYPE 3 CONNECTOR COLOR GL-Class PTS T CONNECTOR NME YER 3 WIRE DESCRIPTION MODEL MKE MERCEDES-BENZ GL-Class MG PTS T COMPONENT LOCTOR PGE 9 OF 3 DOC.: # TYPE - WIRE CHRT - OF CanH 0 pin Brown/Red Keyless GO Module, under body panel beside rear left seat. B CanL 0 pin Brown Keyless GO Module, under body panel beside rear left seat. B CanH 0 pin Brown/Red Keyless GO Module, under body panel beside rear left seat. B CanL 0 pin Brown Keyless GO Module, under body panel beside rear left seat. B CanH 0 pin Brown/Red Keyless GO Module, under rear left seat. CanL 0 pin Brown Keyless GO Module, under rear left seat. CanH 0 pin Brown/Red Keyless GO Module, under rear left seat. CanL 0 pin Brown Keyless GO Module, under rear left seat. CanH 0 pin Brown/Red Keyless GO Module, under rear left seat. CanL 0 pin Brown Keyless GO Module, under rear left seat.

10 PGE 0 OF 3 DOC.: # TYPE - WIRING DIGRM - OF WRNING STEP -TO CONNECT THE MODULE: FOLLOW STEPS TO 4 -TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO CONNECT TO VEHICLE VEHICLE WITH OEM KEYFOB TO TEST CONNECTIONS BLCK 8 PIN B (VEHICLE HRNESS) MODULE STEP CONNECT TO MODULE IGNITION SWITCH BLCK 8 PIN BLCK 0 PIN RELY STEP 3 B BLCK PIN CONNECT TO MODULE BLUE 6 PIN BLCK PIN (VEHICLE HRNESS) WHITE PIN CONNECTIONS INSTRUCTIONS ON NEXT PGE REFER TO WIRE CHRT ND COMPONENT LOCTOR KEYLESS GO MODULE CONNECT PINK/RED - CNH PINK/BLCK - CNL BLCK PIN (NOT USED) CONNECT STEP 4 CONNECT IF REQUIRED WHITE 0 PIN IF NOT EQUIPPED WITH N OEM HOOD SWITCH, INSTLL N FTERMRKET HOOD SWITCH HOOD SWITCH 07 GRY/WHITE - HOOD STTUS (-) INPUT 08 GRY/BLCK (NOT USED)

11 TYPE - WIRING DIGRM - OF PGE OF 3 DOC.: # INSTRUCTIONS TO CONNECT CN WIRES TO KEYLESS GO MODULE KEYLESS GO MODULE - DISCONNECT BLCK CONNECTOR FROM KEYLESS GO MODULE () CONNECTOR 5- INSERT VEHICLE CN WIRES IN PROVIDED HOUSING TO INSULTE THEM - REMOVE VEHICLE CNH WIRE (BROWN/RED) ND CNL WIRE (BROWN) FROM CONNECTOR () 3- INSERT CNH WIRE (PINK/RED) ND CNL WIRE (PINK/BLCK) FROM PROVIDED HRNESS INTO VEHICLE CONNECTOR () CONNECTOR KEYLESS GO MODULE 4- RECONNECT BLCK CONNECTOR INTO KEYLESS GO MODULE ()

12 MODULE PROGRMMING PROCEDURE - STD KEY - OF LED is solid RED. Insert key into ignition. Turn key to ON position. ON Wait, LED will turn solid GREEN then will turn solid RED. >> WRNING: If LED flashes RED/GREEN, turn ignition to position. The vehicle is PTS. Follow appropriate PTS sections. 07 ON Module Programming Procedure completed. Turn key to position. Remove key from ignition. ON 06 PGE OF 3 DOC.: # ON vehicle for 30 seconds. LED will remain solid RED. Wait, LED will turn solid GREEN then will turn.

13 MODULE PROGRMMING PROCEDURE - PTS - OF STOP ON LED is solid RED. Push start button to ON position. 07 ENGINE STOP Wait, LED will flash RED/GREEN. Disconnect the PIN Keyless GO connector from T-harness. The vehicle parking lights will begin to flash. Reconnect the PIN Keyless GO connector to T-harness. LED will turn solid RED. The vehicle parking lights will stop flashing. STOP ON Push start button to position. STOP ON ENGINE STOP PGE 3 OF 3 DOC.: # Module Programming Procedure completed. vehicle for 30 seconds. LED will remain solid RED. ENGINE STOP 06 Wait, LED will turn solid GREEN then will turn.

14 VLET MODE PROGRMMING PROCEDURE - OF >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. Time restriction. Complete next step within 7 seconds. ON >> PGE 4 OF 3 DOC.: # To exit valet mode: repeat steps to 4 then vehicle for 5 seconds. Cycle ignition ON five times [5x /ON] rapidly. Parking Light will flash once [x]. ENGINE STOP Wait, Parking Light will flash twice [x], pause for.5 second, then will flash once [x] to indicate that the valet mode is ON or twice [x] to indicate that the valet mode is. Turn ignition to position. ON ENGINE STOP Valet Mode Programming Procedure completed.

15 FTERMRKET REMOTE PROGRMMING - OF PGE 5 OF 3 DOC.: # FTERMRKET REMOTE PROGRMMING: NOTES I ll aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures.

16 PGE 6 OF 3 DOC.: # MODULE NVIGTION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP 3. >> Module must be programmed to the vehicle. >> Use the Module Navigation Chart on the next page. 06 Set ignition to position. 07 TO ESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 ON TO ESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step 3. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. 3 MNDTORY: EXIT MODULE NVIGTION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. 4 Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE STOP [X]

17 PGE 7 OF 3 DOC.: # [Y] OPTIONS [X] MENUS MODULE NVIGTION CHRT: NOTES I Default settings are listed in bold. ON ON ON ON ENBLE DISBLE* 45 SEC 90 SEC MIN MIN DISBLE N/ LOCK + UNLOCK + LOCK LOCK + LOCK + LOCK MIN MIN 0 MIN 5 MIN 5 MIN MIN MIN 08 5 MIN SEC SEC 08 SEC 0 SEC 5 SEC 06 0 SEC 07 5 SEC SEC 0-5 N/ N/ N/ II Make sure the option is covered on the vehicle before attempting to change the setting [Z] SETTINGS MODULE NVIGTION CHRT - OF DISRM/UNLOCK BEFORE RELOCK FTER RELOCK FTER SHUTDOWN FORCE UNLOCK LL ON FIRST PRESS TKEOVER SECURE TKEOVER DELY FCTORY KEYLESS RS SEQUENCE CONFIGURTION Technical Support only MODULE RUN TIME WIT TO DELY N/ *Vehicle will shutdown when a door is opened.

18 [X] NUMBER OF PRKING LIGHT FLSHES DIGNOSTIC REMOTE ER ERROR CODES - OF I WRNING: The following applies only when the parking lights are connected and supported by the system. Foot brake is ON. Hood is open. II fter a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. 09 RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 0 N/ N/ N/ 3 N/ 4 N/ 5 N/ 6 CN communication failure during RS sequence. REMOTE ER ERROR CODES: NOTES PGE 8 OF 3 DOC.: #

19 I II III DURING PROGRMMING DURING REMOTE WITH IGNITION DIGNOSTIC TEST MODULE LED STTUS MODULE DIGNOSTICS - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN dditional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. PGE 9 OF 3 DOC.: #

20 MODULE RESET PROCEDURE - OF Disconnect all connectors from module except the BLCK 0-PIN connector. 07 Reconnect all connectors. Disconnect the BLCK 0-PIN connector. 08 Repeat programming procedure. PRESS ND HOLD the module s programming button while connecting the BLCK 0-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. Wait, LED will flash RED. RELESE programming button. LED will turn RED for seconds. 06 Module RESET completed. PGE 0 OF 3 DOC.: #

21 TKEOVER PROCEDURE - OF >> ll vehicle doors must be closed and locked prior to remote start sequence. 06 Press and release BRKE pedal. Time restriction. Complete steps to 6 within 45 seconds. 07 Take over procedure completed. Unlock driver door. >> Failure to follow procedure will result in vehicle engine shutdown. Open driver door and enter vehicle. Close driver door. ON PGE OF 3 DOC.: # Push start button once [x] to ON position OR turn key to ON position. ENGINE STOP

22 INSTLLTION CHECKLIST - OF PGE OF 3 DOC.: # CHECKLIST WRNING: Vehicle engine will start many times. Test in a well ventillated area. Open driver door window for easy vehicle access. Enter vehicle. Start the vehicle and let it run for 5 seconds. Stop the vehicle and exit vehicle. Close all vehicle doors, hood and trunk. 06 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. QUESTION : Does the vehicle remote start? YES: Go to step Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat step 6 and call technical support if the problem persists. QUESTION : Does the vehicle shut down? YES: Go to step Open hood. NO: Repeat step 7. If the problem persists, unlock the door using the OEM keyfob, enter vehicle and press brake pedal to shut down the vehicle and call technical support. QUESTION 3: Is the orange warning sticker "Sticker " placed under the hood? YES: Leave hood open and go to step Close all doors. 0 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. NO: Put the mandatory orange warning sticker "Sticker ", leave hood open and go to step 9. QUESTION 4: Does the vehicle remote start? YES: Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Go to question 5. NO: Go to step. QUESTION 5: Is the vehicle equipped with a factory hood switch? (Inside hood latch) YES: The module does NOT detect the hood signal from the vehicle communication network. Call technical support. Close hood. Enter vehicle. Do NOT press brake pedal. 3 Close all doors. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 5 Wait for the vehicle to start. 6 Press brake pedal. NO: Install the mandatory hood switch included in the kit. Repeat installation checklist. QUESTION 6: Does the vehicle shut down? YES: Go to step 7. NO: The module does NOT detect the brake pedal signal from the vehicle communication network. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle and call technical support.

23 INSTLLTION CHECKLIST - OF PGE 3 OF 3 DOC.: # CHECKLIST 7 Exit vehicle. 8 Close all doors. 9 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 0 Wait for the vehicle to start. QUESTION 7: Is the vehicle equipped with a keyless authorization system (Keyless Go)? YES: Touch the exterior driver door handle to unlock door using the keyless authorization system (Keyless Go). Within 45 seconds, go to step. Open driver door. NO: Press UNLOCK button once [x] on the OEM keyfob. Within 45 seconds, go to step. QUESTION 8: Does the vehicle shut down? YES: The module does NOT detect the unlock signal from the vehicle communication network. Call technical support. Enter vehicle. NO: Go to step. QUESTION 9: Is the vehicle equipped with a keyless authorization system (Keyless Go)? YES: Push vehicle start button once [x]. Go to step 3. 3 Press and release brake pedal. NO: Insert key into ignition and turn key to ON position. Go to step 3. QUESTION 0: Does the vehicle shut down? YES: Repeat this procedure from step 3. If the problem persists, call technical support. 4 Shut down the vehicle. 5 Installation checklist completed. NO: Go to step 4.