GENERAL SPECIFICATIONS FOR END DUMP WITH PLOW AND SPREADER
|
|
- Tabitha Powell
- 5 years ago
- Views:
Transcription
1 GENERAL SPECIFICATIONS FOR END DUMP WITH PLOW AND SPREADER Any additions, deletions or variations from the following specifications must be noted. Any items appearing in the vehicle manufacturers regularly published specifications are assumed to be included in the vendor s proposal. The specifications are modeled on a Peterbilt Model 348. Vehicle Type: Model 348 G.C.W.: 58,000 lbs. minimum Engine and Equipment: PACCAR PX-9 345@1900 GOV@2100 Carb Engine Idling Compliance PACCAR 130 Amp Alternator, Brushless w/voltage Immersion Type Pre-Heater V 2 PACCAR Premium 12V Dual Purpose Batt 1400 CCA Big Switch Battery Disconnect 2-Speed Fan Clutch for Frequent Start/Stops C-Brake By Jacobs, PX-9 Spin-On Fuel Filter Frame Mounted Heated Exhaust Single RH Side of Cab Curved Tip Sandpipe(s) Transmission and Equipment: Allison 3000 RDS-P Transmission, Gen 5 (1) Dash Mounted Single Acting Air PTO Control Programming Allison Snowplow Auto Neutral Activates With Parking Brake Allison 6-Speed Configuration, Close Ratio Gears Dash Mounted Push Button Shifter Air and Trailer Equipment: Bendix AD-IS EP Air Dryer w/heater Berg Pull Cord Drain Valve(s)-All Air Tanks Body Connections 5 ft BOC Rear Axle: Dana Spicer DSP41 40,000 lbs. PHP10 Iron LMS Hubs Diff Lock Both Axles Bendix Air Cam Rear Drum Brakes 16.5x7 Ratio 5.29 Rear Axle Peterbilt Air Trac 40,000 lb, 52 in Axle Spacing Front Axle and Equipment Dana Spicer D2000F 20,000 lb, 3.5 in Drop
2 Taper Leaf Springs, Shocks 20,000 lb Power Steering TRW THP60 Dual PHP10 Iron LMS Hubs Bendix Air Cam Front Drum Brakes 16.5x6 Tires and Wheels: FF: BR 20 PLY 315/80R22.5 M860A RR: BR 14 PLY 11R22.5 M770 FF: Accur Steel Rims RR: Accur Steel Rims Fuel Tank: 26 in Alum 90 Gal Fuel Tank LH BOC DEF Tank Mounted LH BOC DEF Tank Small Frame and Equipment: 10 3/4 steel Rails to 354 in, 10.75x3.5x.375 Dimension, 2,136,000 RBM; Yield Strength: 120,000 PSI Full Steel Inner Liner FEPTO Provision 27.8 Bumper Extension Battery Box & Bumper: Aluminum Battery Box LH Under Cab Aftertreatment RH U/C Alum Non-Slip Cab Entry Steel Bumper Swept Back Painted Black, FEPTO only Cab and Equipment: Aluminum Cab 108 in BBC Metton Hood w/bright Crown Severe Service Cab Package #1 Thermal Insulation Package in Cab Rubber Fender Lips 2 in Wide Drivers Armrest RH Only Air Ride Driver High Back Driver Fabric Driver Non-Air Ride Passenger Low Back Passenger Vinyl Passenger Adjustable Steering Column-Tilt Only Manifest Pouch on Rear Cab Wall Extended Rear Window ipo Std Window-Day Cab Combo Fresh Air Heater/Air Conditioner Outside Sunvisor-Stainless Steel Stainless Steel Mirrors 7x16 w/heat Element (2) Convex 8 Inch SS Mirror Power Package-Includes Power Door Locks and Power Windows (1) Air Horn 24.5 in Chrome-Round w/horn Shield
3 ConcertClass Without CD, Includes BT Phone and Audio, AM/FM, WB, USB and MP3 CB Terminals/Wiring Mtd Under Header CB Antenna Mounting, LH Mirror CB Antenna Mounting, RH Mirror Plug In Auto Reset Circuit Breaker Triangle Reflector Kit Shipped Loose 5 lb 3A:40bc Fire Extinguisher Cab Mounted Backup alarm(107db) Buzzer on Air Suspension Dump Valve Dual Output Sensors for Road & Engine Speed (5) Aero LED Marker Lights Daytime Running Lights (1) F/O Loadlight, Switch & (1) 10 ft Wire Coil Vehicle Color: Exterior: N85020 A- L0006EB White - Stand Bed: 15 Mark E Henderson Dump Body (no exceptions) Unibody design with no crossmembers One piece sloping sides with 60 front head & 54 tailgate One piece 3/16 grade 50 floor supported by 8 I-beam long sills 86 inside width; 96 outside width Dump body must be 100% fully welded, skip welds will not be accepted All side braces, tailgate braces, lower & upper rails on tailgate & sides must be of dirt shedding design. Seamless floor & sides joined by continuous welded 5 radius 10 ga. Grade 50 steel headsheet sides & tailgate construction Double weld-on horizontal side braces Contoured front corner posts 7ga. Grade 50 steel rear bolsters tied to an 8 deep reinforced rear apron 52 tall air operated tailgate with triple horizontal bracing Telescopic cylinder with internal doghouse 6 x8 x1/2 rear hinge assembly with 2 diameter hinge pins connected thru 2-1/2 greaseable hinge blocks 22 x86 10ga. Cab shield, Cab shield 12 bolt-on asphalt lip Vibco heavy duty vibrator with timer & dash mounted switch Light kit with a one-piece wiring harness for stop/turn/tail lights & clearance lights in rear bolsters (2) Whelen LED oval amber strobe lights installed in rear bolsters with switch mounted in cab Camero slide-n-go belt driven tarp system with a black mesh tarp & 12 bows Heavy duty custom pintle plate with D-rings (Franklin County to supply pintle hook) Mud flaps installed behind rear duals
4 Dump body to be painted Imron white (no substitutions) Henderson 14ft. FSH-II 304 Stainless Steel Spread (no exceptions) 304 Stainless Steel construction Sides, ends & side supports to be 10ga. 304 stainless steel Salt/sand spreader with 56 side height with a sloped front Standard top grate screens Replaceable 7ga. 304 stainless steel floor Longsills to be 7ga. 304 stainless steel with formed chain shields Cross sills to be 3 formed 7ga. 304 stainless steel, welded to side supports All hopper hardware to be stainless steel Grease tubes extended to rear of spreader 304 stainless steel chute assembly with a 20 SS spinner with replaceable spinner vanes. Chute shall have (2) spread pattern adjustable baffles with (5) adjustments, (4) bottom spinner deflectors which all are adjustable except the forward one & the chute shall have a bypass chute to unload the granular material. Chute shall be constructed of 10ga. 304 stainless steel. Rear discharge pintle chain conveyor to be 24 wide Chain tension adjusting rod to be 5/8 diameter stainless steel Conveyor sprockets to be 6 tooth self cleaning cast iron Spreader to be tied into dump body with a trunnion latch fabricated using 2 x3 x1/4 rectangular tubing, 1-1/4 shaft & 3 x3 x1/4 angles which shall be bolted to spreader. Trunnion latch painted black ( 4) 2 ratchet straps shall be included to keep spreader from moving Spreader to be plumbed complete & ready for operation Henke Snow Plow Henke Model: 36R11IS (no exceptions) 11 Reversable snow plow with Quick Hitch 3/16 moldboard, 36 tall with (6) ½ x4 curved vertical ribs Ribs welded to 2 x3 x3/8 moldboard top angle & bottom end welded to a 1 thick steel bottom rib pivot reinforcement The pivot reinforcement is to be welded to a 4 x4 x5/8 bottom angle Adjustable running gear with 8 steel wheels The circle push frame & the A-Frame shall be heavy duty construction Universal quick hitch, plow portion shall have, two self-aligning receiving jaws The receiving jaws shall be on 33-1/2 centers Cutting edge shall be 1/2 x8 x132 cutting edge Plow shall be equipped with a cushion valve & it shall be mounted to truck Quick hitch The truck Quick Link hitch shall be low profile, bottom of hitch to the top angle shall be no more than 31
5 Hitch shall have a telescoping lift arm with the outer tube constructed of 4 x4 x3/8 and the inner tube shall be 3 x3 x1/4 tubing Truck quick hitch shall be welded to a 5/16 formed channel bumper with the outer 18 of the bumper swept back on each side. Bumper shall be bolted to truck frame with a minimum of (6) 5/8 grade 8 bolts on each side. (2) Stress bars 1 x3 shall be installed & bolted to 4 x6 x1/2 angles which will be bolted to frame over axle. The truck hitch & bumper assembly shall be painted gloss black. Certified Power Hydraulic System Chelsea hot shift PTO installed with a Parker direct mounted pump Pump sized to operate a dump body, spreader & snow plow 30 gallon oil reservoir with a sight/temp gauge, suction strainer, magnetic drain plug & a screened fill cap A 1-1/4 filter & head shall be installed adjacent to the oil tank. The filter & head shall be mounted even with the top of tank so filter can be removed without losing oil. Filter shall include a sight gauge. Control Valve to be a DVA20 series & it shall be arranged as follows: Single acting work spool for dump body (#12 o-ring port) Single acting work spool for plow raise with detent in lower position Double acting work spool for plow angle (plow sections shall be #10 o-ring ports) Control valve shall have power beyond to spreader valve An SG Dual knob spreader valve shall be installed in cab in a spreader control tower as close to driver as possible. An SA-ID detented RVC head to control dump body & a DA-2 dual axis control head to control snow plow shall be installed in cab in a control tower. Morse cables shall be used to control valve sections A complete hose & fitting kit shall be installed. All hoses shall be sized appropriately. There shall be a full flow ball valve on the suction side of the tank. Spreader hoses shall be ran to right rear of truck frame & include quick couplers
2017 Single Axle 5 CU.YD. Dump Truck Specifications. Minimum Specifications 33,000 lb
2017 Single Axle 5 CU.YD. Dump Truck Specifications Item GVW Wheelbase Cab to Axle Minimum Specifications 33,000 lb 158 inches 84 inches Tires 11R x 22.5, Tubeless, 14 ply, All weather mud and snow tread
More informationDANA SPICER WIDE TRACK IPO STD FRONT AXLE(S)
Plant: CHASSIS NUMBER: 268033 MODEL: 337 M CUSTOMER NAME: LIN'S PROPANE TRUCKS WHEELBASE: 208.00 CAB TO AXLE: 138.20 CAB TO END OF FRAME: 220.00 AXLE TO BACK OF CAB: 69.80 OPTION 3371 200700 203020 515010
More informationCUSTOMER NAME: LIN'S PROPANE TRUCKS CHASSIS NUMBER: MODEL: 337 WHEELBASE: CAB TO AXLE:
CHASSIS NUMBER: 268035 MODEL: 337 CUSTOMER NAME: LIN'S PROPANE TRUCKS WHEELBASE: 208.00 CAB TO AXLE: 138.20 CAB TO END OF FRAME: 220.00 AXLE TO BACK OF CAB: 69.80 OPTION 3371 200700 203020 515010 612170
More informationREQUEST FOR QUOTATIONS
Public Works Department REQUEST FOR QUOTATIONS 12 14 YARD DUMP TRUCK PURCHASE Due: Thursday, July 27, 2017 No later than 2:00 P.M. Submit to: City of Arroyo Grande Attn: Public Works Department 1375 Ash
More informationMONTGOMERY COUNTY PUBLIC WORKS DEPARTMENT P. O. BOX 663 INDEPENDENCE, KANSAS PH FAX
MONTGOMERY COUNTY PUBLIC WORKS DEPARTMENT P. O. BOX 663 PH. 620-330-1170 - FAX 620-330-1177 MEMO To: From: Dump Truck Bidders Jim Wright Asst. Public Works Coordinator Date: February 23 rd 2016 Subject:
More informationGALLATIN PUBLIC UTILITIES
GALLATIN PUBLIC UTILITIES Bid Proposal Item: Single Axle Dump Truck Bid Date: Company Address: Phone Number: Manufacturer: Bid Information (1) Prices F.O.B., 249 Hancock Street, Gallatin, Tennessee 37066.
More informationALLEGAN COUNTY ROAD COMMISSION SPECIFICATION FOR BIDS
ALLEGAN COUNTY ROAD COMMISSION SPECIFICATION FOR BIDS PROPOSAL FOR DUMP BOX BODIES, V BOX SPREADERS, UNDER BODY SCRAPERS, PLOW WINGS, FABRICATION AND ASSEMBLY OF COUNTY DUMP TRUCKS Board of County Road
More informationINSTRUCTIONS TO BIDDERS AND SPECIFICATIONS FOR A 7-8 CUBIC YARD DUMP TRUCK
INSTRUCTIONS TO BIDDERS AND SPECIFICATIONS FOR A 7-8 CUBIC YARD CITY OF FOREST 120, SOUTH DAVIS ST P.O. BOX 298 FOREST, MS. 39074 RE: One or More New Dump Truck, Purchase And / Or Lease Purchase Financing.
More informationCity of New Haven. 101 FRONT STREET PO BOX 236 NEW HAVEN, MO Phone * * Fax
City of New Haven 101 FRONT STREET PO BOX 236 NEW HAVEN, MO 63068 Phone 573-237-2349 * www.newhavenmo.org * Fax 573-237-4696 August 20, 2014 Request for Bids, Medium Duty Truck City of New Haven The City
More informationTOWN OF FARRAGUT. Bid Specifications For 2017 Dump Truck. William McKelvey Public Works Director Municipal Center Drive Farragut, TN 37934
TOWN OF FARRAGUT Bid Specifications For 2017 Dump Truck William McKelvey Public Works Director TOWN OF FARRAGUT 11408 Municipal Center Drive Farragut, TN 37934 (865) 966-7057 BID SPECIFICATIONS for 2017
More informationRequest for Bids INFORMATION FOR BIDDERS. FURNISH THE CITY OF DERBY, KANSAS, ONE (1)2014 or NEWER TANDEM AXLE 10 YARD DUMP TRUCK w/ PLOW
Request for Bids City of Derby Public Works 2015-027 INFORMATION FOR BIDDERS FURNISH THE CITY OF DERBY, KANSAS, ONE (1)2014 or NEWER TANDEM AXLE 10 YARD DUMP TRUCK w/ PLOW 1. Sealed bids, on the attached
More informationConcord Road Equipment Mfg., Inc. NorEast-R. Severe Duty Combination Dump Body Spreader with Flat Floor and Integral Center Conveyor
Body Lengths Standard available body lengths (inside of headsheet to inside of tailgate) are 9ft, 10ft, 11ft, 13ft, and 15ft; special sizes are available upon request Understructure Construction Longitudinal
More informationInvitation No: Additional available options:
Invitation No: 044-14 Additional available options: The choice of any of these options, is in lieu of, or in addition to the base bid for the State of Ohio and subject to final engineering approval. Some
More informationTruck Specs. Sabre 9 Off-Highway GCWR: 242,000. CapacityTrucks.com
Truck Specs Sabre 9 Off-Highway GCWR: 242,000 CapacityTrucks.com Sabre 9 / Off-Highway - Base Model Base Model Sabre 9 / Off-Highway Basic Overview GCWR: 242,000 Basic Overview Axle: 4x2 Basic Overview
More informationAn ISO 9001:2000 Certified Company Autocar MY x DOT/EPA Compliant Terminal Tractor Standard Specifications
An ISO 9001:2000 Certified Company Autocar MY 2015 4x2 2013 DOT/EPA Compliant Terminal Tractor Standard Specifications Engine and Equipment Standard Optional Engine model Exhaust Air cleaner Radiator Fan
More informationALLEGAN COUNTY ROAD COMMISSION PROPOSAL FOR WESTERN STAR TANDEM REAR AXLE DUMP TRUCKS (CAB & CHASSIS) MINIMUM 64000# GVWR
ALLEGAN COUNTY ROAD COMMISSION PROPOSAL FOR WESTERN STAR TANDEM REAR AXLE DUMP TRUCKS (CAB & CHASSIS) MINIMUM 64000# GVWR Board of County Road Commissioners of the County of Allegan 1308 Lincoln Road Allegan,
More informationRUGGED CONSTRUCTION SUPERIOR DESIGN IN TRUCK BODY FABRICATION
RUGGED CONSTRUCTION SUPERIOR DESIGN IN TRUCK BODY FABRICATION A DIVISION OF PB9600 STANDARD PLATFORM/ STAKE BODIES SHOWN EQUIPPED WITH 12' Body with Optional Wood Floor Triple Window in Bulkhead Stake
More informationADDENDUM 2. The following clarifications, changes, additions, and/or deletions are hereby made to the RFB:
Date: January 2, 2018 ADDENDUM 2 RFB No: FS-07-18 / Haul Truck Bid Date: January 11, 2018/2:00 PM Local Time The following clarifications, changes, additions, and/or deletions are hereby made to the RFB:
More informationWarranty - Standard Equipment & Specs
Warranty - Standard Equipment & Specs Warranty Basic Distance Unlimited miles Months 24 months Powertrain Distance Unlimited miles Months 24 months Corrosion Perforation Distance Unlimited miles Months
More informationThe bidder shall furnish a complete set of Operator, Service, and Parts Manuals with each body sold.
2013 Model or current production year 34,000 G.V.W.R. Cab and Chassis INTENT: These specifications describe a Dump Truck. GENERAL TERMS: All equipment furnished under this contract shall be new, unused,
More informationTender Town of Yarmouth Equipment Purchase 5 Ton Single Axle Truck Complete with dump box, slide-in spreader, pre-wet system, and spreader controls.
Tender Town of Yarmouth Equipment Purchase 5 Ton Single Axle Truck Complete with dump box, slide-in spreader, pre-wet system, and spreader controls. General Instructions: 1. All bids must be submitted
More informationINVITATION TO BID ONE (1) 10-FOOT DUMPBODY DUMP TRUCK WITH DIESEL / CNG OPTIONS
P. O. B o x 1 5 4 0 T h o m a s v i l l e, G A 3 1 7 9 9 2 2 9-227- 7 0 0 0 F A X 2 2 9-227- 3 2 4 3 w w w. t h o m a s v i l l e. o r g INVITATION TO BID ONE (1) 10-FOOT DUMPBODY DUMP TRUCK WITH DIESEL
More informationWinning Bidder. Monroe Truck Equipment
Bid results for purchase and delivery of Two (2) QuadAxle Plow Equipment Packages-2018 To be installed by Waupaca County Winning Bidder Monroe Truck Equipment Dump Body: 17' 6" inside length x 84" inside
More informationMANISTEE COUNTY ROAD COMMISSION 2019 TANDEM AXLE TRUCK SPECIFICATIONS AND BID REQUIREMENTS (ALTERNATE BID) January 4, 2018
GENERAL 1. The following minimum specifications are for a tandem axle truck (conventional cab and chassis with an engine and transmission). 2. The truck shall be the manufacturer s current model under
More informationZip's Truck Equipment. 316 W. Milwaukee Street New Hampton, Iowa Phone: Fax: Visual Inspection.
Zip's Truck Equipment 316 W. Milwaukee Street New Hampton, Iowa 50659 Phone: 641-394-3166 Fax: 641-394-4044 Visual Inspection Page: 1 of 6 Customer: Address: Division: Phone: null Reference #: 2NPRLZ9X37M730087
More informationNOTICE TO BIDDERS. ONE (1) NEW TANDEM AXLE TRUCK (cab & chassis)
NOTICE TO BIDDERS The Roscommon County Road Commission will receive sealed bids until 2:00 p.m. on Thursday, March 22. 2012. (Bids will be opened at 2:00 p.m. for tabulation and review. Bid results and
More informationSPECIFICATIONS FOR 4X4 SINGLE AXEL PLOW TRUCK. City of Negaunee
SPECIFICATIONS FOR 4X4 SINGLE AXEL PLOW TRUCK City of Negaunee The following specification describes the minimum requirements for a 4x4 single axel plow truck for the City of Negaunee. The equipment bid
More informationGU533 MACK TRUCKS ARE BUILT TO BUILD
TRUCKS ARE BUILT TO BUILD STANDARD POWERTRAIN SPECIFICATIONS ENGINE: CUMMINS ISL9 345 Peak Horsepower 345HP at 1900 RPM Horsepower 330 HP at 20 Gov. RPM Max. Torque 1150 lb/ft at 1400 RPM V-MAC IV Total
More informationINFEED HOPPER COMPONENTS. Parts may not be exactly as shown. Bandit. Copyright 1/12
INFEED HOPPER COMPONENTS 80 INFEED HOPPER COMPONENTS 1. 626-200019 Folding Pan for Infeed Hopper 2 a. 900-4901-83 Folding Pan Spring Lock & Trap Door Lock b. 900-7900-93 Black Rubber Cap (Not Shown) 3
More informationCITY OF TACOMA Environmental Services Department - Solid Waste Management
CITY OF TACOMA Environmental Services Department - Solid Waste Management ADDENDUM NO. 2 DATE: September 11, 2018 REVISIONS TO: Request for Bids Specification No. ES18-0279F Solid Waste Yard Tractors NOTICE
More informationSpecifications for: Hi-Way Model SA-6C 304 Stainless Steel Under Tailgate Spreader Comply to. Make and Model Bid: HOPPER AUGER MECHANISM
Hi-Way Model SA-6C 304 Stainless Steel Under Tailgate Spreader GENERAL 1. The under tailgate spreader required in these specifications shall be hydraulically operated and shall consist of a steel trough,
More informationQUOTE For a 2017 Fire Department Conventional Truck Chassis-Water Tender With PTO Pump
Town of Wascott PO Box 159,Wascott, WI 54890 Phone: 715/466-4252 Email: wascott@centurytel.net QUOTE For a 2017 Fire Department Conventional Truck Chassis-Water Tender With PTO Pump Note: Bidders must
More informationWinning Bid Meets Specifications Meets Specifications Yes/No Deviations Yes/No Deviations
Minimum Specifications/Questionnaire Bid Result for One (1) Purchase and Installation of Tandem Axle Plow Equipment Monroe Truck Equipment Winning Bid DUMP BODY: General: 14 inside length x 84 inside width
More informationPage 1. Equipment: RSP Moldboard Only Serial # RSP RSP Qty: 2. Equipment: OWP Serial # OWP Qty: 1
NON STOCK INVENTORY The following units are currently in stock and discounted for immediate delivery. All units are new, unless otherwise stated and sold AS IS. Standard manufacturer s warranty on pumps,
More informationNOTICE OF BID. The City of Pigeon Forge is receiving bids on four trucks for the Public Works Department.
NOTICE OF BID The City of Pigeon Forge is receiving bids on four trucks for the Public Works Department. Specifications may be obtained from the Public Works Department in City Hall between the hours of
More informationWarranty - Standard Equipment & Specs
Warranty - Standard Equipment & Specs Warranty Basic Distance Unlimited miles Months 24 months Powertrain Distance Unlimited miles Months 24 months Corrosion Perforation Distance Unlimited miles Months
More informationCustomer Proposal. Rush Medium Duty Truck Center, Dallas Irving Blvd., Dallas, Texas, Office: Prepared for: Prepared by:
Customer Proposal Prepared for: Lonnie Sullivan Republic Services 18500 N. Allied Way Phoenix, AZ 85054 Prepared by: Gary Gibson Office: 214-678-5922 Email: gibsong@rushenterprises.com Date: 01/26/2017
More informationGU812 MACK TRUCKS ARE BUILT TO BUILD
GU812 TRUCKS ARE BUILT TO BUILD STANDARD POWERTRAIN SPECIFICATIONS ENGINE: MP7-325M Peak Horsepower 325HP at 1500-1900 RPM Horsepower 300 HP at 2100 Gov. RPM Max. Torque 1200 lb/ft at 1100-1350 RPM V-MAC
More informationNOTICE OF BID. The City of Pigeon Forge is receiving bids on three trucks for the Public Works Department.
NOTICE OF BID The City of Pigeon Forge is receiving bids on three trucks for the Public Works Department. Specifications may be obtained from the Public Works Department in City Hall between the hours
More informationNOTICE OF BID. The City of Pigeon Forge is receiving bids on one knuckle boom trash loader for the sanitation department.
NOTICE OF BID The City of Pigeon Forge is receiving bids on one knuckle boom trash loader for the sanitation department. Specifications may be obtained from the Public Works Department at City Hall between
More informationCustomer Proposal. Rush Medium Duty Truck Center, Dallas Irving Blvd., Dallas, Texas, Office: Prepared for: Prepared by:
Customer Proposal Prepared for: Lonnie Sullivan Republic Services 18500 N. Allied Way Phoenix, AZ 85054 Prepared by: Gary Gibson Office: 214-678-5922 Email: gibsong@rushenterprises.com Date: 01/27/2017
More informationHale Trailer Brake & Wheel
Hale Trailer Brake & Wheel 062290 Design Type: FRAMELESS DUMP TRAILER BODY SPECIFICATIONS Genesis Design - INBOARD Length: 32'-0" Width: 96" Overall Side Height: 66" (64"+2") Aluminum Height: 64" Top Rail
More informationCustomer Proposal. Rush Medium Duty Truck Center, Dallas Irving Blvd., Dallas, Texas, Office: Prepared for: Prepared by:
Customer Proposal Prepared for: Chris Limongelli Republic Services 14400 N. 87th St, Suite 200 Scottsdale, AZ 85260 Office: 480-718-6528 Mobile: 602-369-1776 Email: climongelli@republicservices.com Prepared
More informationPHILLIPS 120V 1000 WATT WITHOUT STEP MOUNTED RECEPTACLE PHILLIPS 120V 1000 WATT WITH STEP MOUNTED RECEPTACLE OIL PAN HEATER
ENGINE AND EQUIPMENT STANDARD OPTIONAL ENGINE MODEL ISB 13, 200 HP @ 2600RPM / 520 FT-LB, CUMMINS ISB 13, 220 HP @ 2600RPM / 520 FT-LB, CUMMINS ISB 13, 240 HP @ 2600RPM / 560 FT-LB, CUMMINS ISB 13, 260
More informationFLAT BED STAKE BODY TRUCK
Group 1 Contract Attachment 4 Price Sheet: Dump Trucks Please see Attachment D: Instruction and General Information for Instructions, Color Key, and Reference Key. GVWR* Code 2 Base Vehicle Description3
More informationTrailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains
Trailer Parts Brake Components Axle Components Suspensions Lights & Electrical Wheels & Tires Loading Ramps Couplers & Safety Chains Trailer Jacks Fenders Dump Trailer Parts Tilt SST Parts Decal Kits Brake
More informationTrailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains
Trailer Parts Brake Components Axle Components Suspensions Lights & Electrical Wheels & Tires Loading Ramps Couplers & Safety Chains Trailer Jacks Fenders Dump Trailer Parts Tilt SST Parts Decal Kits Brake
More informationNOTICE OF LETTING PATROL TRUCK ACCESSORY EQUIPMENT
NOTICE OF LETTING PATROL TRUCK ACCESSORY EQUIPMENT Quotes close at 10:00 A.M., February 18, 2015. The Columbia County Highway Committee will meet in the conference room on the second floor of the Highway
More information54 For RoadWorks customer service, call DOOR AND WINDOW TRIMS 379 VISOR AND WINDSHIELD ACCESSORIES 379 GRILL INSERTS
379 VISOR AND WINDSHIELD ACCESSORIES Multi-Fit Ultracab Visors 60 Multi-Fit Flat Top Visors 60 Flat Top Blind Mount Visors 61-62 Ultracab Blind Mount Visors 62-63 Flat Top Standard Mount Visors 64 Ultracab
More informationABS Components Air Compressors Air Dryers & Cartridges Air Tanks. Air Disc Brakes Bearings Brake Pads Brake Rotors Brake Shoes & Kits Camshafts & Kits
Air Brake Systems ABS Components Air Compressors Air Dryers & Cartridges Air Tanks Air Valves Brass Fittings Composite Fittings Coiled Air Hoses Glad Hands Nylon Tubing Rubber Hose Tire Valves Brake &
More informationThe TARCO Highlander JR is heavy-duty type material spreader that can be used for a variety of light to medium duty truck applications.
THE BASICS: The TARCO Highlander JR is heavy-duty type material spreader that can be used for a variety of light to medium duty truck applications. Typical buyers of these types of machines include municipalities,
More informationIndicates Winning Bid
Bid results for purchase and delivery of Two (2) Tandem Axle Plow Equipment Packages To be installed by Waupaca County Indicates Winning Bid Monroe Truck Equipment Dump Body: 14' 6" inside length x 84"
More informationGU713 BUILT FOR THE JOB
GU713 BUILT FOR THE JOB STANDARD POWERTRAIN SPECIFICATIONS ENGINE: MP7-325M Peak Horsepower 325HP at 1500-1900 RPM Horsepower 300 HP at 2100 Gov. RPM Max. Torque 1200 lb/ft at 1100-1350 RPM V-MAC IV Total
More informationRAC EXPORT TRADING Germany Tel
Technical Specification Kenworth 963S oilfield truck, new GAWR RATINGS Front Axle Weight Rating 40.000 Lb. 18.140 kg Rear Axle Weight Rating 150.000 Lb 68.030 kg Gross Vehicle Weight Rating 190.000 Lb.
More informationISUZU N-SERIES (REG CAB) DIESEL CAB/CHASSIS SPECS NPR-HD (14,500# GVWR)
MODEL YEAR 2017 MANUFACTURER ISUZU MODEL NPR-HD (diesel) GVWR 14,500# *Optional Wheelbases WHEELBASE 109.0 132.5 * 150.0 * 176.0 * CA DIMENSION 86.5 110.0 127.5 153.5 BOC DIMENSION 7.7 7.7 10.2 10.2 USABLE
More informationTRUCKINGTRUTH.COM T T. Daniel B s Pre-Trip Inspection Checklist
TRUCKINGTRUTH.COM T T Daniel B s Pre-Trip Inspection Checklist 1 My pre-trip begins as I approach the vehicle. I am looking for leaks, leaning one way or the other (which may indicate a low tire or bad
More informationType 3 Fire Engine Model 346
Type 3 Fire Engine Model 346 Issue Date: February 2016 Supersedes: February 2014 Type 3 Fire Engine, Model 346 Supersedes February 2014 Page 1 Table of Contents Record of Revisions 3 1 General 4 1.1 General
More informationRefuse Dump Wrecker STANDARD POWERTRAIN SPECIFICATIONS. Mack Trucks, Inc.,
STANDARD POWERTRAIN SPECIFICATIONS Refuse Dump Wrecker Mack Trucks, Inc., Allentown, Pennsylvania ENGINE: MP7-325M Peak Horsepower 325HP at 1500-1900 RPM Horsepower 300 HP at 2100 Gov. RPM Max. Torque
More informationTHE Municipality of Hastings Highlands. Request for Proposal for supply and delivery of one (1) current year
THE Municipality of Hastings Highlands Request for Proposal for supply and delivery of one (1) current year TANDEM AXLE DIESEL TRUCK CAB AND CHASSIS COMPLETE WITH PLOW/SAND COMBINATION UNIT Notice to vendors:
More information1ASD-6CDSS-6P-1D-2S-LM "Salt Special" sander, dual spinner, w/unidirectional reversible auger, includes extra salt shields (Per Ea)
PRICE SCHEDULE 8.0 TO PROVIDE - Make and Model FALLS 1ASD-6 Stainless Steel Under tailgate type, 6" dia (carbon steel) 6" pitch, single auger, direct hydraulic drive, LH Discharge w/poly self-leveling
More information13AU609H063 (1999) Page 1 of 25 Axle & Wheels Front And Steering Assembly
13AU609H063 (1999) Page 1 of 25 Axle & Wheels Front And Steering Assembly 13AU609H063 (1999) Page 2 of 25 Axle & Wheels Front And Steering Assembly 1 683-0304 1 S Frame 2 710-0604A 1 /P Self-tapping Screw,
More informationI N V I T A T I O N F O R B I D S NOTICE TO BIDDERS
I N V I T A T I O N F O R B I D S NOTICE TO BIDDERS The City of Alamosa Department of Public Works, 300 Hunt Avenue, Alamosa, CO will be accepting bids until 1:30 p.m., December 19, 2016, for a 2016 Automated
More informationBANNOCK COUNTY SOLID WASTE
BANNOCK COUNTY SOLID WASTE 1500 N. Fort Hall Mine Road Pocatello, Idaho 83204 Ph. (208) 236-0607 NEW 2018 ROLL-OFF BID PACKAGE The undersigned hereby agrees and proposes to furnish one (1) new 2018 (make)
More informationISUZU NPR-HD REG CAB CAB & CHASSIS SPECS 14,500# GVWR DSL
MODEL YEAR 2014 MANUFACTURER ISUZU MODEL NPR-HD DSL GVWR 14,500# *Optional Wheelbases WHEELBASE 109.0 132.5 * 150.0 * 176.0 * CA DIMENSION 86.5 110.0 127.5 153.5 BOC DIMENSION 7.7 7.7 10.2 10.2 USABLE
More informationSNOW PLOW, FRAME, HYDRAULIC SYSTEM, DUMP BODY, WING, SPREADER AND PRE-WET TANK SYSTEM
DEKALB COUNTY HIGHWAY DEPARTMENT SNOW PLOW, FRAME, HYDRAULIC SYSTEM, DUMP BODY, WING, SPREADER AND PRE-WET TANK SYSTEM Sealed proposal for the furnishing and installing of snow plow, frame, hydraulic system,
More informationi. ii. iii. iv. 1. HYDRAULIC CYLINDER PIVOT PIN GREASE TWO PLACES 2. 5 TH PLATE- DRAFT ARM CONNECTION GREASE TWO PLACES 3. DRAFT ARM- BOLSTER CONNECTION GREASE TWO PLACES 4. HIGH LIFT GATE HINGE GREASE
More informationIt don t mean a thing If it ain t got the swing
SWING CHUTE SAND/SALT SPREADER INSTALLATION AND OPERATING INSTRUCTIONS SWING CHUTE SPREADER MODELS: 7, 8, 9, 9.5 & 10 MANUAL FOR SPREADER SERIAL NUMBERS AFTER # 20000 It don t mean a thing If it ain t
More informationAddendum 2 Minimum Specifications One New Twin-Screw Diesel-Powered Cab & Chassis For the Sanitation Division
Minimum Specifications One New 2018-2019 Twin-Screw Diesel-Powered Cab & Chassis For the Sanitation Division General: Axles: 1. GVWR 53,200-lbs. 2. Wheel Base As required for CA (cab to axle) 3. Front
More informationDump Bodies Version of Excel used: CONTRACTOR BODY Warranty
Dump Bodies Contract end Date 09-30-18 Vendor Name: Contact Person: Street Address: P.O. Box: City, State, Zip Phone #: Toll Free #: Fax #: Email Address: Website: ABM Equipment & Supply, LLC. Sam Fahey
More informationTHE CORPORATION OF THE CITY OF GRAND FORKS
THE CORPORATION OF THE CITY OF GRAND FORKS 7217 4TH STREET, BOX 220 GRAND FORKS, BC VOH 1H0 FAX 250-442-8000 TELEPHONE 250-442-8266 Addendum no.1 Request for Proposal : Title: PW2017-01-RFP Plow / Sand
More informationSTATE OF MINNESOTA. 5.0 DUMP BODY SCOTT ALUMINUM Make. LANDSCAPER BODY Warranty. 1 YEAR BODY, DEALER PRICE LIST Date & I.D.
Vendor Name: ABM EQUIPMENT & SUPPLY, LLC. PRICING PAGE Contact Person: RON ZIMMER Street Address: 333 2ND STREET NE P.O. Box: City, State, Zip HOPKINS, MN 55343 Phone #: 952-938-5451 Toll Free #: 800-229-5451
More informationPennsylvania State Police Tactical Mounted Unit. 25,500# GVWR Crew Cab Tractor
Pennsylvania State Police Tactical Mounted Unit 25,500# GVWR Crew Cab Tractor The following pages specify the design and component requirements for a crew cab truck tractor. In addition to the vehicle
More informationNORTH CAROLINA SHERIFFS ASSOCIATION
NORTH CAROLINA SHERIFFS ASSOCIATION Name of Dealership Type of Vehicle Zone LOADMASTER EXCEL "S" REAR LOADER - 31 YARD (Specification #76) Base Unit Price 2016 Loadmaster Excel "S" Rear Loader - 31 Yard
More informationNORTH CAROLINA SHERIFFS ASSOCIATION
NORTH CAROLINA SHERIFFS ASSOCIATION Name of Dealership Type of Vehicle Zone LOADMASTER EXCEL "S" REAR LOADER - 20 YARD (Specification #73) Base Unit Price 2016 Loadmaster Excel "S" Rear Loader - 20 Yard
More informationWarranty - Standard Equipment & Specs
Warranty - Standard Equipment & Specs Warranty Basic Powertrain Corrosion Perforation Distance Unlimited miles Months 36 months Roadside Assistance Diesel Engine Distance 250000 miles Months 60 months
More informationPart s Catalog. GT2100 Garden Tractor. Model No. 14AP80RP744. Original Instructions (EN) (01/31/06)
Part s Catalog GT0 Garden Tractor Model No. AP0RP Original Instructions (EN) -0 (0//0) Model P0RP -0-00 Turf Tire, x. x -0-00 Rim,.0 x.0-00 Lug Nut, /- -00A-0 Wheel Assembly, x. x -00-00 Rim Assembly,.0
More informationGS12 Grape Spreader. Illustrated Parts Breakdown
GS Grape Spreader Illustrated Parts Breakdown Page Front End Assembly Page Axle Assembly Page Floor & Apron Page Pump Assembly Page Page Hydraulics Manifold Components Page Gearbox Components S/N - Page
More informationLAPEER COUNTY ROAD COMMISSION 2015 Truck Equipment
LAPEER COUNTY ROAD COMMISSION 2015 Truck Equipment Bidders please note that any and all exceptions to the specifications must be noted in areas provided. Failure to disclose any and all exceptions or deviations
More informationMINIMUM SPECIFICATIONS FOR SOLID WASTE TRANSFER TRAILER(S)
MINIMUM SPECIFICATIONS FOR SOLID WASTE TRANSFER TRAILER(S) MINIMUM TECHNICAL REQUIREMENTS FOR AN ALUMINUM COMPOSITE OPEN TOP TRANSFER TRAILER Bidder shall complete each item with either a check mark "
More informationGSN-8 Spreader. Illustrated Parts Breakdown. Page 1 Front End Assembly Page 2 Axle Assembly Page 3 Floor & Apron Page 4 Pump Assembly
GSN- Spreader Illustrated Parts Breakdown Page Front End Assembly Page Axle Assembly Page Floor & Apron Page Pump Assembly Page Hydraulics Page Manifold Components Page Manifold Cover Page Gearbox Components
More informationSTATE OF MINNESOTA PRICING Page % DISCOUNT
TRAILERS: DUMP BODY, LOWBOYS, FLATBED, TAG, SLIDE AXLE, UTILITY, GOOSENECK, ENCLOSED, ETC. Vendor Name: Truck Utilities Inc Contact Person: Paul Warner Street Address: 2370 English Street P.O. Box: City,
More information1- Body capacity The minimum capacity of the body, excluding hopper area is:
1- Body capacity The minimum capacity of the body, excluding hopper area is: 10.5 cu.yd. 2- Body dimensions The body is rounded to permit maximum capacity. Inside body width is: Outside body width is:
More informationMB3 Chassis with Front Mount Plow
MB3 Chassis with Front Mount Plow Reference Only. Shown with optional 24 Ft folding plow Reference Only. Shown with optional 24 Ft flared plow Chassis with four wheel Tru-Trac 4 x 4 drive. 164-inch wheel
More informationPart s Catalog. LX500 Lawn Tractor. Model No. 13AP60RP744. Original Instructions (EN) (01/31/06)
Part s Catalog For Parts Call 0-- or 0-- LX00 Lawn Tractor Model No. AP0RP Original Instructions (EN) -0 (0//0) For Parts Call 0-- or 0-- Model P0RP NUMBER --00 Turf Tire, 0 x 0.0 x -000-00 Rim,.0 x.0-0-0
More informationMEYER MATE 9.0 CU FT. SPREADER
MEYER MATE 9.0 CU FT. SPREADER General Specifications Overall Height: 41.25" Overall Width: 49.5" Overall Depth: 32" Weight Empty: 140 lbs. Spreading Width: Minimum 3 Maximum 30 Spreading Material: Dry
More informationAUTOMATED REFUSE TRUCK RIGHTHAND OPERATING, DIESEL POWERED
AUTOMATED REFUSE TRUCK RIGHTHAND OPERATING, DIESEL POWERED The unit(s) to be furnished under this proposal shall be a diesel powered, Low Entry, Tilt Cab with Cab over chassis, Color White, automatic transmission,
More information365 & 450 Model Grain Wagons
365 & 450 Model Grain Wagons Features 30 side slope and 40 end slope on the gravity box. Heavy duty bracing on slant side of box and rigid internal box reinforcing braces. Rocking bolster is standard on
More informationSpecifications For MEYER UTG GEAR STAINLESS STEEL. General: Comply Exception
MEYER UTG GEAR STAINLESS STEEL General: This under tailgate shall be of the bottom opening design. The entire unit shall rigidly mount to the side of the dump box with single pin quick detachable hardware.
More informationSection Index Cross Reference: Sorted by Buffers Model Numbers REF-1 to -9 Cross Reference: Sorted by Penz Model Numbers REF-10 to -18
Section Index Cross Reference: Sorted by Buffers Model Numbers REF-1 to -9 Cross Reference: Sorted by Penz Model Numbers REF-10 to -18 1000 - LANDING LEG PARTS Sandshoes: Low Profile 1001-1 to -3 Sandshoes:
More informationLine Body Canopy and Accessories:
ATTACHMENT A Heavy Crew Truck Line Body and Accessories Installation. TMWA provided cab & chassis specifications are provided on last page The Cab & Chassis will be a Freightliner (All Other Items Referenced
More informationMOBILE MIXERS PARTS MANUAL HIGH ROUGHAGE, STATIONARY, TRUCK & TRAILER MODELS. Serial number up to
MOBILE MIXERS PARTS MANUAL 405-470 - 540 HIGH ROUGHAGE, STATIONARY, TRUCK & TRAILER MODELS Serial number up to Harsh International, Inc. 600 Oak Ave. Eaton, CO 80615-0007 (970) 454-2291 Fax: (970) 454-3491
More information2018 Kenworth T880 Roll-off Trucks
2018 Kenworth T880 Roll-off Trucks Pioneer Tarper Included Only $174,900 Plus F.E.T. 2018 KENWORTH WITH PIONEER RACK N PINION TARP Engine Information ISX Cummins 425 H.P. @ 1800 RPM Paccar MX-13 430 H.P.
More informationCITY OF ROCK ISLAND S P E C I F I C A T I O N S
CITY OF ROCK ISLAND S P E C I F I C A T I O N S It is the intent of the City of Rock Island to receive bids on fourteen (14) snow plows. The proposed plows will be used by the Public Works Departments
More information4X2 CXU632. Line Haul Pickup & Delivery STANDARD POWERTRAIN SPECIFICATIONS. Mack Trucks, Inc.,
4X2 CXU632 STANDARD POWERTRAIN SPECIFICATIONS ENGINE: CUMMINS ISX12-G 400 Horsepower 400 HP [298 kw] @ 1800 RPM Max. Torque 1450 lb/ft @ 1200RPM Engine Type - 4 Cycle, Spark Ignited, Inline 6 Cylinder,
More informationTOWN OF CHAPLIN BID SPECIFICATION REQUIREMENTS 2018 OR LATER 37,780 DUMP TRUCK AND SNOW FIGHTING EQUIPMENT PACKAGE
TOWN OF CHAPLIN BID SPECIFICATION REQUIREMENTS 2018 OR LATER 37,780 DUMP TRUCK AND SW FIGHTING EQUIPMENT PACKAGE The Town of Chaplin is seeking bids for a new Department of Public Works 37,780 GVW Truck
More information9895 Combine Parts Catalog EFF. S/N HSC8101
9895 Combine Parts Catalog EFF. S/N HSC8101 1 FORWARD ALPHABETICAL INDEX The complete alphabetical index appears at the beginning of this publication. It is used to locate major groups, assemblies and
More informationSchedule "B'" 2015 Tandem Combination Snowplow/Sander Specification
General Specifications Is the vehicle to be supplied made up from individual components that meet or exceed the specifications outlined in the following pages of the tender? Where minimums are called for,
More informationMAKE AND MODEL. Engine: Tier 4 Compliant? Yes or No. Turning Radius Fuel Tank Size Rear Axle Rating 21,000. Rear Suspension Rating 21,000
Vendor Name: Hoglund Bus & Truck Contact Person: Chris Sexton Ben Stone Street Address: 116 E Oakwood Drive P.O. Box: 249 City, State, Zip Phone #: 319-290-2882 Fax #: 763-295-4992 Email Address: bstone@wayneusa.com
More informationMUNICIPAL SNOW & ICE CONTROL EQUIPMENT NOTHING WORKS LIKE A DOGG
MUNICIPAL SNOW & ICE CONTROL EQUIPMENT NOTHING WORKS LIKE A DOGG Our History 1946 Buyers Products Company founded by Sam Ruven and Bessie Kleinman as a distributor of driveline components. Buyers continued
More informationSPECIFICATIONS FOR TRUCK EQUIPPED WITH AERIAL LIFT AND SERVICE BODY Pennsylvania Department of Military and Veteran Affairs
Page 1 of 5 SPECIFICATIONS FOR TRUCK EQUIPPED WITH AERIAL LIFT AND SERVICE BODY Pennsylvania Department of Military and Veteran Affairs Insulated Telescopic Articulating type aerial lift with the following
More information