INDEX FOR RIG INVENTORY Rig 225

Transcription

1 INDEX FOR RIG INVENTORY 225 SECTION A B C D E F G H I J K L M N O P CATEGORY HOISTING EQUIPMENT ROTARY EQUIPMENT PUMPING AND HIGH PRESSURE DISCHARGE SYSTEM LOW PRESSURE MUD SYSTEM PRIME MOVERS / TRANSMISSION / ELECTRIC AUXILIARY EQUIPMENT BLOWOUT PREVENTION AND WELL CONTROL EQUIPMENT RIG FLOOR EQUIPMENT DRILL STRING PARAMETERS RECORDING/INDICATING EQUIPMENT FISHING TOOLS SAFETY EQUIPMENT CAMP EQUIPMENT TRANSPORT WATER PUMPING EQUIPMENT WAREHOUSE 1

2 Number 225 SECTION A : HOISTING EQUIPMENT A 1 A 2 Drawworks OIME TBA Drive type - Electric or Mechanical Mechanical. Auxiliary Brake - Make, Model, Typ Baylor 6032 Maximum Input HP 2000 hp. Drum Size (OD X L) and Line Size 23 inch x 48 inch Lebus grooved. Line size 1 1/4 inch Catworks Catheads - Make & Mode Foster 24 AH make up. 37 AH breakou Hoisting Capacity in Low/with number lines strung up 700,000lb in Low with 10 lines Crown Block Safety Device - Make Model, Type. Possi Stop system with ABB Koomey Phuematic Toggle Back up Mast Parco Model - HH136A-800K cantilever split leve Dimensions - Clear Height, Mast Base Width, Crown Width Height 136' + 15' extension Mast base width 27' Crown Width 9' 11" x 7' Maximum Rated Static Hook Load (No Gross Nominal Capacity) 800,000 lbs. Hook Load Rating with number of line 705,000 with 10 lines Adjustable Stabbing Board (adjustable stroke) with 15' Adjustable Stroke Crown Block - Type Parco M/S. Crown Block Sheaves Number - Size & Line Size Six (6) x 48 inch. Line size 1 1/4 inch. Crown Block Fast Line Sheave -Size & Line Size One (1) inch. Line size 1 1/4 inch. Mast Racking Capacity, with size DP 17,856 ft of 5 inch drill pipe Bumper Blocks under crown ( Y or N Tubing Board Available ( or No No. A 3 Substructure Make and type Clear Height under Rotary Beams Nominal Height (Floor Height Max. Set-back Load, (lbs. Max. Casing (rotary beams) (lbs Matting Boards ( or No Parco. 17.9ft. 21 ft. 550,000 lbs. 680,000 lbs. A 4 BOP Handling Device Travelling blocks and slings Make and type Certified slings Lift capacity 15 ton each 2

3 Number 225 A 5 A 6 Traveling Assembly Block, Type and Rating Ideco UTB 360. Block Sheave Number, Size, Line Siz Five 42 inch. Line size 1 1/4 inch Hook, Type and Rating Ideco 360 ton. Elevator Links, Size, Length and Ratin 132 inch x 350 ton. Elevator Links, Size, Length and Ratin 130" x 350 ton. Elevator Links, Size, Length and Ratin 160 inch x 500 ton Drilling Line Make (EIPS or EEIPS) EEIPS. Nominal Diamete 1 1/4 inch. Length 5000' Equipped with spooling system - Type No 3

4 Number 225 SECTION B : ROTARY EQUIPMENT B 1 Top Drive No B 2 Rotary Table and Equipmen Make and type Oime 27 1/2" Opening 27 1/2" Drive (Thru Drawworks or Independently Driven) Compounded Maximum Input HP 2000 Master Bushings MSPC Static Load Rating 570 ton Bowl Inserts for Casing # 1, #2 and #3 4

5 Number 225 SECTION C: HIGH PRESSURE MUD SYSTEM C 1 C 2 Mud Pumps Number 2 x CE F1000 and 1 x GD PZ-9 Make & Model Continental Emsco F 1000 and one GD PZ9 Drive (Electric or Mechanical). Model & Make Mechanical, Caterpillar D-398 with Twin disk HUD transmission Maximum Input Horse Power per Pump 770 HP Suction dampener. Make & Mode #1 & #2 CE Discharge dampener. Make & Mode #3 Mattco and #1 & #2 CE F-1000 Reset Relief Valves. Make & Model Reset Relief Valve, Titan class Type "C Charging Pumps. Number, Make & Model 1 x Halco " x 8", One Mission Magnum 6" x 5" Suction Strainer Double strainer Discharge Strainer High Pressure Mud Lines Discharge Line. Single & Dual, Interna Diameter. Single 4" Working Pressure 5000 psi Standpipe Manifold 5" Pressure gauges - range and resolutio psi Rotary Hose. Size, Length, WP 75' x 3" I.D x 7500 ps Standpipe (s) Single, Dual, Size, WP Single 4" and 5" Spare Rotary hose. Size, Length, WP Tesco, 4" x 75 x 7000 ps 5

6 Number 225 SECTION D : LOW PRESSURE MUD SYSTEM D 1 Mud Mixing With No Bulk Bag mixing Gantry Hoppers - Make & Model MCM 3" Location top of mud tanks Low Pressure Pumps - Make & Type Halco 2500 centrifical 8" x 6" Drive - Electrical or Engine Driven Electric motor 75 HP Covered Area mixing Facilities D 2 Turbo Shear High speed mixer Location Reserve Tank Low Pressure Pumps - Make & Model Mission 6x8 Drive - Electric or Engine Driven elecric 100 hp Covered Area No Mixing Facilities 2" hopper D 3 D 4 Active Mud Tanks Tank 1 (Dimensions & Capacity in barrels) Shale Shaker tank Tank 2 (Dimensions & Capacity in barrels). Tank 3 (Dimensions & Capacity in barrels). Tank 4 (Dimensions & Capacity in barrels). Tank 5 (Dimensions & Capacity in barrels). Tank 6 (Dimensions & Capacity in barrels). Pill Tank included in active system /No (capacity in barrels) Sand Trap included in active system (capacity in barrels) Reserve Mud Tank Tank 1 (Dimensions & Capacity in barrels) Tank 2 (Dimensions & Capacity in barrels) Shaker tank,sand trap 25bbl, and settling tanks 157bbl Total Ca 220bbls to Bottom of Trough Degasser and desander total 220 bbls to bottom of trough Active reserve, total 145 bbls to bottom of trough Active pit 145 bbls total to bottom of trough Suction pit 220 bbls total from bottom of trough Slug tank, 110 bbls 110 bbls 25 bbls 375 bbls 375 bbls D 5 D 6 Trip Tank Total Capacity in bbls, Number of Compartments & Capacity of each. One 100 bbls Incremental Volume (bbl/inch.97 bbls/ inch Level Indicator (Mechanical/Electronic) Electrical Location (Independent tank/part of Active Mud System) Seperated from Active Fill System (Pumps & Motors Sizes) 2" x 3" mission pump w/- 25 HP electric moto Trip tank manifold Two (2) outlets Shale Shaker Number Three (3) derrick flo-line shakers Max flow rate (GPM) 525gpm w/- 10.4ppg over 210 mesh sreen 6

7 Number 225 D 7 High "G" Dryer Derrick Flo-line Make and type Super G No. of cones - sizes 20 x 4" on mud cleaner and 3" x 10" on desande Max flow rate (GPM) the desilter 1200 gpm and the desander 1500 gpm Feed Pump - make and type 2 x Halco Supreme 8" x 6" Drive Motor 75 HP electric motor D 8 D 9 Water Tank ( Water) Number Three (3) Capacity 235 bbl's each Flow Meters No Pumps - make and type Transferred through mixing pumps Drive Motors - make and type Mixing pumps as above Pit Volume Totalize Mud System - make and type AOI 2800 Tanks Monitored Active, intermediate and trip tanks Floor Display & Other Display Acadianna monitor in Supt and Companymans offic Mechanical Indicators Electrical floats 7

8 Number 225 SECTION E : PRIME MOVERS / TRANSMISSION / ELECTRIC E 1 Diesel Engines Number Four (4) Manufacturer Caterpillar Model D343 Continuous Output (HP) at RPM 425 HP E 2 Transmission Twin Disc Manufacturer Twin disc Model TAC 51 Output Drive Type Drive Line E 3 Generators Caterpillar D-3412 Number Two (2) Manufacturer Caterpillar Type SR4 Output (KW) 475 KW Drive Motor Caterpillar E 4 AC Distribution system Manufacturer Type Input/Output -Transformers Westinghouse HTUL Y/ 120 volt International Transformer Corp, 75 KVA 3N 60 HZ E 5 Fuel Tanks Number Two (2) Capacity (Barrels) 235 BBL Equipped with sight gauge and marked by inch calibration /No Dip Stick in inches Fuel Flow Meters /No Double Wall Tank /No No Fuel Filter System - Make & Mode yes, Nelson and Windslow Pumps - make and type Mission3x4 Drive Motors - make and type Siemans RG Hp 8

9 Number 225 SECTION F : AUXILIARIES, DRILLING RIG SKIDDING F 1 F 2 F 3 F 4 F 5 F 6 F 7 Cutting & Welding Number Cutting Two (2) Number Portable Welding Machines Two (2) Millar Big 30A and Millar Big Blue 302P Air Compressors Number Three (3) Make and type GD- EBP 99 J-100HP 440CFM / Plus 2 x 30 HP Power Supply & Pressure 415 volts 120 ps Air Receivers (Volume) Six (6) totalling 150Cubic fee Two (2) at compressor skid and Two (2) in sub base and Four (4) unde Location of Air Receivers Draworks Air Drier Gardener Denve Wireline Unit Make & Type Mathey Wire Size Length 15000' Power Electric Chicksan Hoses Type FMC Size 2" Max. Working Pressure Rating psi Number Four (4) Straights None Elbows One (1) Loops 12' Tees None Valves One (1) Doghouse Number One (1) Size 10' x 8' Location - (Driller, Off Driller, Bottom Driller Workshop (Mechanic/Electric) Number Three (3) Size 20' Other Catwalks Two (2) Pipe racks - Number of Sets Five (5) Steam Cleaner No F 8 Cellar Jet Number Make and type Flow rate Two Parker Design 900gpm 9

10 Number 225 F 9 Cellar Air Pumps Number Two (2) Make and type Wilden 3" Flow rate F 10 Skidding Type Manual Pulley system using Travel block and drawork 10

11 Number 225 SECTION G: BLOWOUT PREVENTION AND WELL CONTROL G 1 Annular Type Preventers Diverter system Number One (1) Size 21 1/4" Hydril Pressure Rating 2000psi Top Connection Studded Bottom Connection Flanged Annular BOP system Number One (1) Size 13 5/8" Hydril GK Pressure Rating 5000psi Top Connection Studded Bottom Connection Hub 10,000 PSI G2 Number Three (3) Size 13 5/8" Pressure Rating 10,000psi Make and type (Singles/Double Cameron Single Type U Top Connection Hub Bottom Connection Hub Side Outlet size, connections 4 1/16' Large Bore Bonnets (/No No Tandem Boosters (/No No G3 BOP's Rams (BOP Size & Pressure) Cameron 13 5/8" 10,000ps 9 5/8" Rams - Sets One (1) 7" Rams - Sets One (1) 5" Rams - Sets Two (2) 3 1/2" Rams - Sets Two (2) Blind Rams Two (2) Variable Bore Rams (Size) One 3 1/2" x 5" 2 7/8" One (1) 2 3/8" One (1) 11

12 Number 225 G 4 Adapter / Spacer Spools Spacer spools Number One (1) mud cross Size 21 1/4" Pressure Rating 2,000psi Height 31 1/2" Bottom Connection Flanged Top Connection Flanged Outlets (Number & Size) 10" and 4 1/16" Number Two (2) mud cross Size 13 5/8" Pressure Rating 10M Height 29 1/2" Bottom Connection Hub Top Connection Hub Outlets, Size 4 1/16" Mud Cross Valves Kill Line - ID and pressure rating 2" 15,000PSI Chicksans Kill Line Valves - No, Type, Size, Rating Two 2 1/16" 10,000psi Flocon Kill Line NRV - No, Type, Size, Rating Two Cameron 2 1/16" 10,000psi Choke Line - ID and pressure Rating 4 1/16" 10,000psi Choke Line Valves - No, Type, Size Rating 4" Manual, 10, /16" Flocon Choke Line HCR- No, Type, Size, Rating One Cameron 4 1/16" 10,000psi Double studded adapters Number One (1) Size 21 1/4" Pressure Rating 3000psi x 2000psi Height 0.13 Number One (1) Size 13 5/8" Pressure Rating 10,000psi x 5,000ps Height 0.19 Number One (1) Size 13 5/8" Pressure Rating 5,000psi x 3,000ps Height 0.19 Number One (1) Size 13 5/8" Pressure Rating 10,000psi x 3,000ps Height 0.19 Number One (1) Size 13 5/8" x 11" Pressure Rating 5,000psi x 5,000ps Height 0.16 Number One (1) Size 13 5/8" x 11" Pressure Rating 10,000psi x 5,000ps Height

13 Number 225 G 5 Risers/Bell Nipples Size 21 1/4" N/A Top Connections Open Bottom Connections Flange Outlets, size 12" Size 13 5/8" Height N/A Top Connections Open Bottom Connections Flanged Outlets, size 12" G 6 G 7 B.O.P. Test Stump Flange Size 13 5/8" Working Pressure 10,000psi Pressure Unit and Control Koomey T S Capacity, Accumulator Pressure 3000 psi No. of Accumulator Bottles Twenty Four (24) Main Control - location On unit no. of station Six Remote Controls - locations Floor no. of stations One Emergency control station Manual on unit Reservoir Capacity 315 gal No. of Electric Pumps One (1) No. of Air Pumps Four (4) G 8 G 9 Portable Test Unit for B.O.P. Power Supply Range Pressure Recorder BOP Wrench Koomey Air 15,000psi Hytorc G 10 Choke Manifold Pressure Rating 10,000psi Positive Choke, Make, Type, Size Cameron 2" Adjustable Choke, Make, Type, CIW adj 2 1/16" Remote Controlled Chokes Swaco super choke Remote Choke Controls Location(s Floor Gate Valves with Flanges Two 4 1/16" - Five 3 1/16" - Seven 2 1/16" 10,000ps Buffer Size and Pressure Rating Capacity of Buffer 13' x 8" =.429 bbl's x 10,000 psi ratin Automatic Choke Control HCR Valve on Choke Line D.P. read out pressure data Driilers console gauge, Swaco gauge 13

14 Number 225 G 11 Gas Control Mud/Gas Separator Poor-Boy Type Make, Type and Size Inlet Size & Connection Outlet Size & Connection Degasser Make Type Capacity Tri-Flo 3" Line to 10" inlet Flange 8" flange Swaco Vacume w/- compressor and 3HP electric motor 34" x 10' = 11.2 bbls G 12 Gray IBOP Valves (Stab In Type Float Valve) Make Hydril Connection Size One 6 5/8" Reg, Two 4 1/2" IF Number Three Minimum I.D. 2 7/8" G 13 Inside BOP'S for Drill String Drop In (Wireline Retrievable Two Make, type and size Hydril Size Connections 4 1/2"IF and 3 1/2"IF Number Two (2) Plug size 2 1/4" and 1 1/2" Minimum I.D. 1 x 2 1/4" and 1 x 1 1/2" Full Opening Valve Make, Type and Size Hydril Connections 6 5/8"REG x 8"OD x 2, 4 1/2" IF x 6 1/2" OD x2, 3 1/2" IF x 4 3/4" x 2 Number Six(6) Grey Valve Size 6 1/2" Connections 4 1/2" IF Number One (1) G 14 Float Valve For 7 5/8 Reg. connections One (1) For 6 5/8 Reg. connections One (1) For 4 1/2 Reg. connections One (1) For 3 1/2 Reg. connections One (1) G 15 Circulating / Side Entry Subs Number Two (2) Size Connections 4 1/2"IF and 3 1/2" IF Side Entry Connection 1502 Pressure Rating 5,000psi G 16 Circulating Heads For Drill String Two (2) Make, Type, Size 4 1/2" IF Top Connection 1502 Bottom Connection 4 1/2" IF 14

15 Number 225 SECTION H: DRILLING RIG FLOOR EQUIPMENT H 1 Elevators H 1.1 Standard - String Elevators Type, Capacity, Number For 5" Drill Pipe One (1) WTM 250 ton For 20" Casing Two (1) BJ SLX 150 Ton For 13-3/8" Casing One (1) Web Wilson 150 Ton For 9-5/8" Casing One (1) Web Wilson 150 Ton For 7" Casing One (1) BJ SLX 150 For 5" casing One (1) Varco 100 Ton H 1.2 Single Joint Elevators - Make & Number For 20" Casing For 13-3/8" Casing For 9-5/8" Casing For 7" Casing For 5" Casing One (1) set BJ One (1) set BJ Two (2)sets one BJ and one (1) Web Wilson One (1) Dencon One (1) Varco H 2 Standard Manual Slips Type, Capacity, Number For 5" Drill Pipe Two (2) SDXL 5 1/2" Body for drillpipe 4 1/2" to 5 1/2" For 4-1/2' Drill Pipe One (1) Wooley 4 1/2" for pipe 4", 3 1/2", 2 7/8" 2 3/8" For 3-1/2" Drill Pipe One (1) Varco SDMC For 9-1/2" Drill Collar One (1) Wooley type A 8 1/4" x 10" For 8-1/4" Drill Collar One (1)Wooley type A 6 3/4" 8 3/4" For 6-1/2" Drill Collar One (1) Wooley type A 5 1/2" x 7 For 20" Casing One (1) Varco CMSXL 5329 For 13-3/8" Casing One (1) Varco CMSXL 5313 For 9-5/8" Casing One (1) Varco CMSXL 5307 For 7" Casing One (1) Den Con H 3 Casing Slip Type Elevators BJ 500Ton H 3.1 Casing Spider (Slip Type) BJ 500Ton H 4 Manual Drill Pipe & Casing Tongs BJ Type B, Woolley Type B, Woolley Sdd For 5" Drill Pipe One (1) For 3-1/2" Drill Pipe Two (2) For 9-1/2" Drill Collar One (1) For 8-1/4" Drill Collar One (1) For 6-1/2" Drill Collar One (1) For 4-3/4" Drill Collar One (1) For 13-3/8" Casing One (1) For 9-5/8" Casing One (1) For 7" Casing One (1) 15

16 Number 225 H 5 H 6 H 7 Drill Pipe Spinning Tong Varco SSW 10 Size Range 3 1/2" - 5" Power Supply Air Power Casing Tongs Size, Make and Mode 13-3/8" Casing power tong One (1) Eckel 13 5/8" Standard and One (1) Eckel 13 5/8" HD 5-1/2" Casing/Tubing power tong Two (2) Eckel Hydraulic Unit for Casing/Tubing Power Tong Two (2) Duetz Number, Make, Model & Capacity F6L912 H 8 Hydraulic Cathead Pheumatic Make and Model Foster Line Pull 30,000 ft/lbs on single line Make up H 9 Dog Collars/Safety Clamp Number Two (2) Varco Size and Range 4 x Varco type C H 10 Bit Breakers To Break 26" Tri-cone bit One (1) To Break 17 1/2" Tri-cone bit One (1) To Break 14 3/4" Tri-cone bit To Break 12 1/4" Tri-cone bit One (1) To Break 10 5/8" Tri-cone bi To Break 8 1/2" Tri-cone bit One (1) To Break 6" Tri-cone bit One (1) H 11 Winches Number Three (3). Ingersoll Rand Line Size 5/8" Capacity 6000lb 11000lb Location floor and Catwalk H 12 Man riding Winch Number One (1). RAM Line Size 3/8" Capacity 1500lb Location Floor H 13 Mud Saver Box One (1) Oteco Mud Guard Size Range 5", 4 1/2", 3 1/2", 2 3/8"-2 7/8". 16

17 Number 225 H 14 Casing Fill-Up Line of Line 2' Cement line O.D. 2" Connections 1502 weco Controls Charge Pump Location Standpipe H 15 Well Fill-Up Line of Line O.D. Connections Controls Location 2" chicksan 1502 weco Charge Pump Standpipe H 16 Stabbing board Height Adjustable, Min/Max Heigh 15' Removable /No Exterior Access Inertia Line provision Run out board/flap fitted Load Test 1500 KG swl Manufacturer Deckard 17

18 Number 225 SECTION I: DRILL STRING I 1 Drill Pipe 5" Size and Grade 5" S-135 Weight 19.5 Range Two (2) No. of joints Four Hundred and Seventy One (471 Tool Joint O.D. 6 5/8" Tool Joint Thread 4 1/2" IF Internal Plastic Coating between 30/70% Thread Protectors Hard banding Smooth Pinchrome and Armaco I 2 I 3 Drill Pipe Pup-Joints Number Three (3) Length 5', 10' 15' Size and Grade 5" S-135 Weight 19.5 Tool Joint O.D. 6 5/8" Tool Joint Thread 4 1/2"IF Internal Plastic Coating Thread Protectors Hard banding No Heavy Weight Drill Pipe Number Twenty Five (25) Size and Grade 5" Weight 49.3 Range Two (2) Tool Joint O.D. 6 5/8" Tool Joint Thread 4 1/2"if Thread Protectors Hard banding 18

19 Number 225 I 4 Drill Collars 9 1/2" OD 9 1/2" ID 3" Length 31' Connection 7 5/8"Reg Number Nine (9) Spiral Grooved (Number Spiral Lift Shoulder Thread Protectors (one per end Slip Recess No OD 8" ID 2 7/8" Length 31' Connection 6 5/8"Reg Number Twenty Five (25) Spiral Grooved (Number Spiral Lift Shoulder Thread Protectors (one per end Slip Recess OD 6 3/4" ID 2 3/4" Length 31' Connection 4 1/2"IF Number Twenty Five (25) Spiral Grooved (Number Spiral Lift Shoulder Thread Protectors (one per end Slip Recess I 5 I 6 Lifting Subs For 9-1/2" DC Five (5) For 8" DC's Six (6) For 6-1/2" DC Five (5) Bit Subs (Bored for float) For 7 5/8 Reg. connections Two (2) For 6 5/8 Reg. connections Two (2) For 4 1/2 Reg. connections Two (2) I 7 Saver Subs Number and Pin Connection Two each 19

20 Number 225 I 8 Cross over subs Pin conn - Box conn Three (3) 7 5/8" x 6 5/8"reg Six (6) 4 1/2" IF x 6 5/8" reg Two (2) 6 5/8" reg x 4" IF One (1) 4" IF x 6 5/8" reg One (1) 6 5/8" reg x 6 5/8" reg Three (3) 4 1/2" IF x 4 1/2" IF Three (3) 4 1/2" reg x 4 1/2" IF Two (2) 4" IF x 4 1/2" IF One (1) 4 1/2" x 4" IF One (1) 3 1/2" EUE x 4 1/2" IF One (1) 4 1/2" IF x 3 1/2" IF One (1) 4 1/2" IF x 4 1/2" reg I 9 Double pin subs - Pin x Pin One (1) 6 5/8" REG x 6 5/8" REG left hand Two (2) 4 1/2" IF x 4 1/2" IF I 10 Bit Subs Two (2) x 6 5/8" REG x 6 5/8" REG One (1) 4 1/2"REG x 4 1/2" IF One (1) 6 5/8" REG x 7 5/8" REG I 11 Kelly Guard Valves Pin _ Box Three (3) 4 1/2" IF x 4 1/2" IF One (1) 6 5/8" REG x 6 5/8" REG I 12 Side Entry Sub One (1) 4 1/2" IF x 4 1/2" IF I 13 Circ Sub Two (2) 4 1/2" IF x 1502 weco I 14 Lift Subs Pin - Box Five (5) 7 5/8" REG x 7 5/8"REG Four (4) 6 5/8" REG x 6 5/8" REG Five (5) 4 1/2" IF x 4 1/2" IF One (1) 7 5/8" REG x 4 1/2" IF Two (2) 6 5/8" REG x 4 1/2" IF 20

21 Number 225 SECTION J: SURVEY TOOLS J 1 Make & Size One Each Totco 1 15/16" Survey running Too J 2 Retrieving Tools One Each J 3 Recording Instructmentation One Each 0-16 Degree Survey Clock 21

22 Number 225 SECTION K: FISHING TOOLS K 1 Reverse Circulating Basket 11 1/2", 7 7/8", K 2 Magnets 10 5/8", 7" K 3 Overshots 11 3/4", 10 5/8", 9 5/8", 8 1/8", 8 1/8", 7 5/8", 5 3/4" K 4 Fishing Jars 6 1/4", 4 3/4" K 5 Bumper Subs 7 3/4", 6 1/4", 4 3/4" K 6 Junk Mills 12", 8 1/8" 22

23 Number 225 L 1 SECTION L: SAFETY EQUIPMENT Eye wash facilities Number and Locations Drench Showers wash Four (4) rig floor, mixing area, welding w/shop, Meck w/sho Three (3) floor, shale shakers, mixing area L 2 Site Fire Extinguishers Twenty Five (25) Type abc Dry Chemical powde Number, Type & Size Size 150lb 3, 30lb 18, 20lb 2, 2 kg crane and forklift L 3 Camp Site Fire Extinguishers Twenty (20) type ABC dry chemical powde Number, Type & Size One (1) 150lb, Nine (9) 30lb, Ten (10) 20lb L 4 Gas Protection Toxic LTX 312 Detect H2S, CO, O2 combustible / LEL Portable Gas Detection Ki Two (2) Gas alarm max detect, H2S, CO,O2, comustible / LE L 5 Fire fighting pump Diesel Portable Fire Pump Camp Manufacturer and type Number of location 3304 Catapillar with Halco 6x5 Smoke detectors One each Room L 6 Breathing Apparatus Full Face Mask with 30 minute bottles Scott 30 min SCBA Number of masks and regulators Six (6) Number of bottles Six (6) 23

24 Number 225 SECTION M: CAMP MAIN AND RIG (IF APPLICABLE) M 1 Main Camp Main Camp Beds for One hundered and Twenty (120 Recreation Facilities Two (2) Kitchen Facilities Two (2) Mess hall Facilities Two (2) Sick Bay One (1) Office Accommodation None Radio Room No Laundry Two (2) Food Storage Uni Two (2) Bath & Toilet Unit One (1) M 2 M 3 M 4 Camp Type Accommodation for Company Ma 30' Office sleeper Type Accommodation for Tool pushe 30' Office sleeper Type Accommodation for Operator Staf 30' sleeper Type Accommodation for Mechanic 30' sleeper Type Accommodation for Mud Enginee 40' sleeper block Type Accommodation for Crew Messing 40' sleeper block Mini CAMP Kitchen facilities No Dining facilities No Total Beds for Security Camp Ten (10) Power M 4.1 Main Camp Generators Make, Type KW Output Caterpillar 3408 PC 380KW M 4.2 Camp Generators Make, Type Caterpillar 3306 KW Output 210 KW Security Camp Generators Make, Type KW Output 24

25 Number 225 M 5 Water - Septic - Main camp M 5.1 Potable water storage capacity Distillation/purification facilities Capacity Goulds pump 510S, 1 HP 115/230v type UC 200bbl M 5.2 Septic Disposal Unit Two (2) Blue Dolpin Capacity 40 BBL M 6 M 7 Intercom System Gaitronics 701 Number of Stations Ten (10) Positions located R/floor, KMC, Logging, M/house,MCC, Dir Drillers, CM, TP, R/Supt M/board Radio System Type Kenwood Antenna Type Hand held Number and Location (s Three in Supt office 25

26 Number 225 SECTION N: TANK STORAGE AND TRANSPORT N 1 Fuel Tanks (Camp) Number Two (2) Capacity 235bbls N 2 Water Tank (Camp) Number Capacity Flow Meters One 200 bbl's No N 3 N 4 Forklift CAT 966 Capacity 6 ton Auxiliary - Bucke Bucket Number One (1) Load Spreading Mats (Matting Boards Type Wooden 6m x 3m x 4" Number Thirty (30) 26

27 Number 225 SECTION O : WATER PUMPING EQUIPMENT O 1 Pumps Type EWCO triplex Number One (1) Power Supply Detroit 8V71 Type Mission 3 x 2x 13 Number One (1) Power Supply electric 25 HP O 2 Water Line Amount One Hundred and Fifty Feet (150' Size 4 1/2" 27

28 Number 225 SECTION P : WAREHOUSE EQUIPMENT P 1 Buildings Sixteen Each Twenty Foot Sea Containers Office One Each Twenty Foot Sea Containers Dollar Value ROM - US$ 1.2 K 28