Project: GKM Block 9 - BFP
|
|
- Emmeline Underwood
- 5 years ago
- Views:
Transcription
1 Project: GKM Block 9 - BFP Location: Mannheim, Germany Year: 2012 HKM111Z kw 6.3 kv 1775 rpm 3 pieces Operation with frequency inverter / efficiency 98.1 %
2 Project: Boxberg Power Plant Block R - BFP Location: Germany Year: 2009 HKM110D kw 10 kv 1478 rpm 1 piece Start-up at 75 % of the nominal voltage against full resisting moment of the pump. Best efficiency (>97 %) at 75 % of the nominal power (usual operation point of this application) Copyright: Vattenfall Europe
3 Project: GKM Block 9 ID-Fan Location: Mannheim, Germany Year: 2012 HKM111Z kw 10 kv 592 rpm 2 pieces Fan Power plant design standard: Start-up after voltage drop against open valve and partial voltage 80 % with reduced start-up current. Focus on low noise level.
4 Project: Wilhelmshaven - BFP Location: Wilhelmshaven, Germany Year: 2012 HKM111Z kw 15 kv 1488 rpm 2 pieces 15 kv design
5 Project: Eemscentraale - MCWP Location: Zwolle, The Netherlands Year: 2011 HKR112Z kw 6.6 kv 295 rpm Tube cooled 1 piece start-up current 4.5x
6 Project: Rotterdam - BFP Location: Rotterdam, The Netherlands Year: 2012 HKM111Z kw 15 kv 1488 rpm 2 pieces Power plant design standard: Start-up after voltage drop against open valve and partial voltage 80 % with reduced start-up current. Focus on low noise level.
7 Project: Moorburg - MCWP Location: Hamburg, Germany Year: 2012 HKM110Z kw 10 kv 297 rpm 6 pieces 80 db without tolerance at load / 20 pole design without forced ventilator / mounting form V1
8 Project: Moorburg ID-Fan Location: Hamburg, Germany Year: 2012 HKM111Z kw 10 kv 592 rpm 2 pieces Fan Power plant design standard: Start-up after voltage drop against open valve and partial voltage 80 % with reduced start-up current. Focus on low noise level.
9 Project: Wai Gao Qiao ID-Fan output extension Location: Shanghai, China Year: 2012 HKM190D kw 10 kv 745 rpm 5 pieces Fan The driven fan has a high moment of inertia (7824 kgm2). Max. permissable start-up time 20 seconds at 77 % rated voltage.
10 Project: Altbach FD-Fan Location: Stuttgart, Germany Year: 2011 HKM180Z / 3800 kw 10,5 / 2,5 kv 50 / 60 Hz 993 / 1191 rpm 1 piece Fan Design with 2 windings: Winding 1 = Operation on mains with 10.5 kv & Winding 2 = Operation with frequency inverter with 2.5 kv & 60 Hz
11 Project: Westfalen Block D&E - BFP Location: Hamm, Germany Year: 2012 HKM110D kw 10 kv 1482 rpm 3 pieces Power plant design standard: Start-up after voltage drop against open valve and partial voltage 80 % with reduced start-up current. Focus on low noise level.
12 Project: GKM Block 9 District Heating s Location: Mannheim, Germany Year: 2012 HCZ545P kw 3.3 kv 1495 rpm Water jacket cooled 3 pieces 1700 kw with utilization of F/B during frequency inverter operation while conforming with the max. acceptable frame size 450 mm.
13 Project: Westfalen Block D&E Oxi Blower Location: Hamm, Germany Year: 2012 HKG550L kw 10 kv 2990 rpm Rib cooled 3 pieces Fan
14 Project: Sostanj Block 6 - BFP Location: Sostanj, Slovenia Year: 2012 HKM110D kw 10.5 kv 1490 rpm 1 piece Efficienecy at 75 % load = % Sound pressure level at no-load = 77.9 db(a) Drive chain length = almost 18 m Run-out after voltage drop against open valve is possible
15 Project: Walsum Block 10 - BFP Location: Germany Year: 2009 HKM111Z kw 15 kv 1490 rpm 2 pieces 15 kv ± 10 % / start-up current 4.4x without tolerance / sound pressure level 82 db(a) at load without tolerance
16 Project: Oroszlany Location: Hungary Year: 2002 Various HKG 710 / 585 / 250 kw 6 kv 1493 / 1492 / 1490 rpm Rib cooled s Protection against 100 % humidity
17 Project: Walsum Block 10 PA-Fan Location: Germany Year: 2009 HKM156E kw 10 kv 1487 rpm 1 piece Fan Sound pressure level 80 db(a) without tolerance / start-up current 5.0x without tolerance
18 Project: Walsum Block 10 ID-Fan Location: Germany Year: 2009 HKM110D kw 15 kv 1745 rpm 1 piece Fan 15 kv ± 10 % / startup current 4.3x without tolerance / sound pressure level 82 db(a) at load without tolerance / design with redundant air/water cooler (4x 50%)
19 Project: Walsum Block 10 FD-Fan Location: Germany Year: 2009 HKM110D kw 15 kv 745 rpm 1 piece Fan 15 kv ± 10 % / start-up current 4.9x without tolerance / sound pressure level 82 db(a) at load without tolerance
20 Project: Walsum Block 10 CEP Location: Germany Year: 2009 HKR171P kw 10 kv 1486 rpm Tube cooled 2 pieces Start-up current 5.0x without tolerance / sound pressure level 83 db(a) at load without tolerance
21 Project: Walsum Block 10 Mills Location: Germany Year: 2009 HKM150D kw 10 kv 984 rpm 4 pieces Mill Start-up torque 200 % / start-up current 5.0x without tolerance
22 Project: Walsum Block 10 - MCWP Location: Germany Year: 2009 HKR112P kw 10 kv 422 rpm Tube cooled 2 pieces Application: Highlight: Start-up current 5.0x without tolerance / sound pressure level 85 db(a) at load without tolerance
23 Project: Walsum Block 10 Absorber s Location: Germany Year: 2009 HKM163D kw 10 kv 493 rpm 4 pieces Start-up current 5.0x without tolerance / sound pressure level 75 db(a) at load without tolerance
24 Project: Voerde Power Plant LV Absorberpumps Location: Germany Year: 2004 HKR190B kw 0.69 kv 495 rpm Tube cooled 2 pieces Quietness stage R (max. 1.8 mm/sec) Operation with frequency converter
25 Project: Voerde Power Plant HV Absorberpumps Location: Germany Year: 2004 HKR190B kw 10 kv 495 rpm Tube cooled 6 pieces Quietness rating R (max. 1.8 mm/sec) / sound pressure at load 77 db(a)
26 Project: Termoli Power Plant MCWP Location: Italy Year: 2005 HKR110D kw 6.6 kv 495 rpm Tube cooled 2 pieces Design with double casing for noise reduction
27 Project: Termoli Power Plant Location: Italy Year: 2005 HKG550M kw 6.6 kv 1493 rpm Rib cooled 2 pieces
28 Project: Termoli Power Plant BFP Location: Italy Year: 2005 HKM156Z kw 3.3 kv 3578 rpm 4 pieces Frequency inverter driven / speed control range rpm / sound pressure level 82 db(a) without tolerance
29 Project: Simmering - MCWP Location: Vienna, Austria Year: 2008 HKR190P kw 6.3 kv 423 rpm Tube cooled 2 pieces
30 Project: Schwedt Power Plant ID-Fan Location: Germany Year: 2006 HKM180D kw 6 kv 995 rpm 3 pieces Fan 80 db at load without tolerance
31 Project: Schwedt Power Plant FD-Fan Location: Germany Year: 2006 HKG556H kw 6 kv 1494 rpm Rib cooled 3 pieces Fan Design with sleeve bearings / sound pressure level 80 db (+3 tolerance) at load
32 Project: Schwarze e Power Plant Location: Germany Year: 2008 HKM163R kw 10 kv 1482 rpm 3 pieces Vertical Design (V1), sound pressure level 80 db(a) without tolerance, start-up current 5.5x without positive tolerance
33 Project: Schwarze e ID-Fan Location: Germany Year: since 1994 HKM110D kw 10 kv 743 rpm 2+2 pieces Fan Low start-up current / low noise (80 db)
34 Project: Rugeley Power Plant - Booster Location: England Year: 2007 HKR111Z kw 11 kv 745 rpm Tube cooled 2 pieces Fan Heavy start-up at 80 % UN / design with sleeve bearings
35 Project: Niederaußem Power Plant ID-Fan Location: Germany Year: 1998 HKM110D kw 10 kv 743 rpm 2 pieces Fan Sound pressure level at load: 77 db(a) [without tolerance]
36 Project: Maritza Power Plant - BFP Location: Bulgaria Year: 2007 HKM171E kw 10 kv 1487 rpm 6 pieces 2nd shaft end for oil pump / reduced starting current 5.2x without tolerance
37 Project: Lippendorf Power Plant - MCWP Location: Lippendorf, Germany Year: 1996 HKL110Z kw 10 kv 330 rpm Air / air cooled 4 pieces Biggest manufactured motor in vertical design / low noise: 80 db(a) at load
38 Project: Lagisza Power Plant Location: Poland Year: 2007 HKM163E kw 10.5 kv 1491 rpm Tube cooled 1 piece 82 db(a) at load without tolerance / 2nd shaft end for oil pump
39 Project: Lagisza Power Plant Location: Poland Year: 2007 HCZ545D kw 10.5 kv 1494 rpm Water jacket cooled 2 pieces Water jacket cooled design / sound level 80 db(a)
40 Project: La Robla 2 Power Plant Location: Spain Year: 2007 HKM180E kw 6.3 kv 744 rpm 1 piece Fan Reduced starting current 4.7x / start-up at 71 % nominal load
41 Project: La Robla 2 Power Plant - Absorberpumps Location: Spain Year: 2007 HKG550K kw 6.3 kv 994 rpm Rib cooled 4 pieces Efficiency > 97 %
42 Project: Iskenderun Power Plant Location: Turkey Year: 2001 HKG550L kw 10 kv 596 rpm Rib cooled 10 pieces
43 Project: Flingern Power Plant Location: Germany Year:2004 HKG545K kw 5 kv 746 rpm Rib cooled 2 pieces Mounting form B3/B5 / additional load at the flange: N
44 Project: Fiddler s Ferry & Ferrybridge - Fan Location: England Year: 2007 HKR111Z kw 11 kv 745 rpm Tube cooled 6 pieces Fan Heavy start-up at 80 % UN / design with sleeve bearings
45 Project: Boxberg Block R ID Fan Location: Boxberg, Germany Year: 2009 HKM111Z kw 10 kv 590 rpm 1 piece Fan Reduced starting current 5.0x without tolerance / suitable for start-up at 75 % rated voltage during full resisting moment Weigth: 42 tons Nom. Torque: 218 knm
46 Project: Boblitz Location: Germany Year: 2004 MKG535K kw 400 V Hz 1425 rpm Rib cooled 3 pieces
47 Project: BoA 2&3, Neurath Power Plant - MCWP Location: Grevenbroich Germany Year: 2007 HKM110Z kw 10 kv 329 rpm 5 pieces Low noise: 80 db(a) at load / start-up current 4.8 (without tolerance)
48 Project: BoA 2&3, Neurath Power Plant - BFP Location: Grevenbroich, Germany Year: 2007 HKM110D kw 10 kv 1478 rpm 4 pieces Reduced starting current 4.8x without tolerance / suitable for start-up at 75 % rated voltage during full resisting moment. Used in the word s most modern twinblock lignite power plant.
49 Project: BoA2&3, Neurath Power Plant - Absorber Location: Grevenbroich, Germany Year: 2007 HKR110B kw 10 kv 424 rpm Tube cooled 13 pieces Design according to power plant standard / noise level 77 db(a) without tolerance at load
50 Project: Abono2 Power Plant Location: Spain Year: 2005 HKM110D kw 6 kv 747 rpm 2 pieces Fan Efficiency 97.9 % / heavy starting duty of an ID-Fan with a moment of inertia of kgm2
We Keep the World in Motion. Power Plants
Power Plants March 2011 Which kind of power plants and applications are our motors used for? ELIN Motoren offers drive solutions for selected applications in all forms of thermal power plants: Pumps -
More informationWe Keep the World in Motion. Power Plants
We Keep the World in Motion. Power Plants www.elinmotoren.at December 2013 Which kind of power plants and applications are our motors used for? ELIN Motoren offers drive solutions for selected applications
More informationSpecial edition POWER - GEN
Special edition POWER - GEN Dear Reader, Special edition POWER - GEN June 2010 www.sarens.com Power Plants Germany pioneered in 2006 the building of a new generation of coal and gas fired power plants.
More informationWe Keep the World in Motion. Motors for Cement Industry
We Keep the World in Motion. Motors for Cement Industry January 2017 Many Facts, why to trust in ELIN Machines Sustainable Development Low Life Cycle Costs High Reliability High Efficiencies High Quality
More informationDYNAS3 LEADING SOLUTIONS FOR DYNAMIC ENGINE TESTING. Explore the future
LEADING SOLUTIONS FOR DYNAMIC ENGINE TESTING DYNAS3 Explore the future Automotive Test Systems Process & Environmental Medical Semiconductor Scientific 2 DYNAS 3 Best-in-class AC dynamometers The HORIBA
More informationwater-cooled motor / generator with up to 13 kw continuous power
water-cooled motor / generator with up to 13 kw continuous power KEY FEATURES permanent magnet synchronous machine water-cooled high peak power for motor applications convincing cost-benefit ratio recommended
More informationMotor Reliable & Technology Drives since 1922 GERMANY. FRANCE. NETHERLANDS. ITALY. SPAIN. RUSSIA. SINGAPORE
Motor Reliable & Technology Drives since 1922 GERMANY. FRANCE. NETHERLANDS. ITALY. SPAIN. RUSSIA. SINGAPORE Experience and Innovation since 3 Generations Johann Helmke 1889 1985 Founder of 1922 Ing. Johann
More informationSingle Phase AC Induction Electric Motors
Single Phase AC Induction Electric Motors Europe s original and finest electric motors providing legendary performance, reliability and engineering design. The AMME range of single phase are capacitor
More informationWe Keep the World in Motion. Company presentation
We Keep the World in Motion. Company presentation www.elinmotoren.at January 2018 ... in Motion. What you can expect from ELIN Motoren: high industrial standards based on decades of experience highest
More informationNCF 60 Hz. Protection class IP 55
The Nederman NCF Fans have direct drive motors which means a safe and cost effective operation. Installing an energy efficient NCF fan with our other Nederman products saves time and reduces energy costs.
More informationSARENS WILBERT Joint Venture
SARENS WILBERT Joint Venture specialists in special applications sale and rental worldwide WOLFF WK 60140B max. 45 t capacity WILBERT Heavy Lifters with up to 128 t capacity WT 905L e.tronic WT 1305L e.tronic
More informationSINGLE PHASE TEFC CAGE MOTORS
SINGLE PHASE TEFC CAGE MOTORS 2 SINGLE PHASE TEF CAGE MOTORS Mechanical protection: IP 54 Voltage: 220 V, 50 Hz Type Output power P N kw Rated speed n N min -1 Efficiency % Power factor cos Rated current
More informationACEA Report. Vehicles in use Europe 2017
ACEA Report Vehicles in use Europe 2017 TABLE OF CONTENTS Summary... 2 Vehicles in use in Europe... 3 Passenger cars... 3 Light commercial vehicles... 4 Medium and heavy commercial vehicles... 5 Buses...
More informationNCF fans 50 Hz. Protection class IP 55
The Nederman NCF Fans have direct drive motors which means a safe and cost effective operation. Installing an energy efficient NCF fan with our other Nederman products saves time and reduces energy costs.
More informationLARGE THREE-PHASE SQUIRREL CAGE ASYNCHRONOUS MOTORS FOR HEAVY DUTY APPLICATIONS ADH SERIES
LARGE THREE-PHASE SQUIRREL CAGE ASYNCHRONOUS MOTORS FOR HEAVY DUTY APPLICATIONS ADH SERIES FRAMES 355 560 355kW 1500kW (1500rpm) FOR INVERTER DUTY Code Declaration of conformity The motors described in
More informationproducts 22 º C Ventilation Air Conditioning Refrigeration Inside PROVIDED BY HEINEN & HOPMAN
products > Duct fan WMR OUTSIDE 35 C HUMIDITY 90% 22 º C Inside PROVIDED BY HEINEN & HOPMAN Heating Ventilation Air Conditioning Refrigeration To stand by our clients in the harshest environments WMR duct
More informationWe Keep the World in Motion. Business Unit Oil & Gas
We Keep the World in Motion. Business Unit Oil & Gas www.elinmotoren.at November 2016 Oil & Gas Why to use ELIN Motoren? Sustainable Development High Reliability High Efficiencies High Quality ATEX certified
More informationLED T8 glass tube 4ft 18W
LED T8 glass tube 4ft 18W A u t h o r i z e d L i c e n s e e f o r T O S H I B A t r a d e m a r k 1. Specification: A. General Data Model 4ft T8 glass tube 18W Product Code 00301315547A 00301315548A
More informationJMC 320 GS-N.L. Technical Description. Cogeneration Unit-Container. with Island Operation no special Grid Code
Technical Description Cogeneration Unit-Container JMC 320 GS-N.L with Island Operation no special Grid Code Electrical output Thermal output 1053 kw el. 1215 kw Emission values NOx < 500 mg/nm³ (5% O2)
More informationBREXIT AND THE AUTO INDUSTRY: FACTS AND FIGURES
BREXIT AND THE AUTO INDUSTRY: FACTS AND FIGURES GLOBAL TRADE European Union EU vehicle imports: Total value: 45,693 million Quantity: 3,395,419 units EU vehicle exports: Total value: 135,398 million Quantity:
More informationHIGH EFFICIENCY INDUCTION MOTORS COMBROHEF001_=
COMBROHEF001_= HIGH EFFICIENCY INDUCTION MOTORS High efficiency induction motors General specifications Rated outputs and efficiency values are in accordance with IEC 60034-30-1 all parameters are measured
More informationWillem van der Westhuizen Pump Consultant Eskom Enterprises Engineering Johannesburg South-Africa. Master Degree in Mechanical Engineering
SELECTING THE OPTIMISED PUMP CONFIGURATION AND DRIVE OPTION FOR THE CONDENSATE EXTRACTION AND BOILER FEED PUMPS FOR THE NEW ESKOM SUPERCRITICAL POWER STATIONS Abstract: Willem van der Westhuizen Pump Consultant
More informationCOMBROIND001_= THREE PHASE SQUIRREL CAGE INDUCTION MOTORS. IE1 motors MAA - BAA Series IE2 motors MAQ - BAQ Series
COMBROIND001_= THREE PHASE SQUIRREL CAGE INDUCTION MOTORS IE1 motors MAA - BAA Series IE2 motors MAQ - BAQ Series 03 07 07 08 12 15 15 16 18 20 SPECIFICATIONS AND STANDARDS IE1 - MAA / BAA Series Technical
More informationProduct Catalogue ARMONIA Providing indoor climate comfort
Product Catalogue ARMONIA Providing indoor climate comfort ARMONIA 1,3-11 kw Water cassette Main applications Light commercial buildings Offi ces Shops General description Why this choice? Silent operation
More informationAUSTRIA. Table 1. FDI flows in the host economy, by geographical origin. (Millions of US dollars)
Table 1. FDI flows in the host economy, by geographical origin World 5 690 138 6 195 3 184 10 784 7 933 31 154 6 858 9 303 840 10 618 5 760 Developed economies 5 740 13 5 341 2 689 10 137 6 291 29 721
More informationNEW COMMERCIAL VEHICLE REGISTRATIONS EUROPEAN UNION 1. November 2018
PRESS EMBARGO: NEW COMMERCIAL VEHICLE REGISTRATIONS EUROPEAN UNION 1 November 2018 Commercial vehicle registrations: +3.8% 11 months into 2018; +2.7% in November Total new commercial vehicles In November
More informationHorizontal Cartridge DUST COLLECTOR OPF
* The level of sound pressure is affected by the background noise, the reverberation of the environment, the presence of other sonorsources and the positioning of the machine near reflecting surfaces.
More informationHIGH TEMPERATURE TWIN SQUIF FANS
HIGH TEMPERATURE FANS HIGH TEMPERATURE FOR SMOKE EXTRACT CERTIFIED TO EN12101-3-2002. 374 029 2085 8200 BENEFITS QUIET AND POWERFUL SOLUTIONS High performance centrifugal motor/impeller combination providing
More informationWORLD MOTOR VEHICLE PRODUCTION BY COUNTRY AND TYPE QUARTERS June 14, 2018
QUARTERS 2017-2018 June 14, 2018 CONTENTS BASEPROTOTAL BASEPROCARS BASEPROLCV BASEPROHCV BASEPROBC Summation of cars, LCVs, HCVs, heavy buses Cars LCVs HCVs Heavy buses Note: The production of cars and
More informationM SERIES. Electric Motors
Electric otors Range They are the most effective and economical answer to needs of alternating current transmission. The threephase motors are available, in accordance with the IEC international standards,
More informationVPC Corporate Presentation
VPC Corporate Presentation 21/22. 09. 2016 Agenda About VPC Services Portfolio Experience & Customers 2 VPC Profil Shareholder palero Locations Range of services Engineering services for power generation
More informationHigh efficiency induction motors
High efficiency induction motors Technical data Type Power Speed Efficiency Power factor Current Rated current Breakdown Sound pressure level Moment of Inertia η cosφ I n T n I s /I n T s T max L pa J
More informationTRANSNORM LOW VOLTAGE MOTORS IC 411 TN LV 1 4E5
TechnicalDocumentation TN LV 1 4E5 TRANSNORM LOW VOLTAGE MOTORS IC 411 Mission, Vision, Targets Our electric motors and generators are optimized in accordance with our client's technical and economical
More informationHFW-350 T5. Generating Rates SERVICE PRP STANDBY. INDUSTRIAL RANGE Soundproof Powered by FPT_IVECO
G1 WATER-COOLED THREE PHASE 50 HZ STAGE 2 DIESEL Generating Rates SERVICE PRP STANDBY Power kva 350 390 Power kw 280 312 Rated Speed r.p.m. 1.500 Standard Voltage V 400/230 Available Voltages V 230-230/132
More informationHDW-200 T5. Generating Rates SERVICE PRP STANDBY. INDUSTRIAL RANGE Soundproof Powered by DOOSAN
E10 WATER-COOLED THREE PHASE 50 HZ STAGE 2 DIESEL Generating Rates SERVICE PRP STANDBY Power kva 200 220 Power kw 160 176 Rated Speed r.p.m. 1.500 Standard Voltage V 400/230 Available Voltages V 230-230/132
More informationTn (Nm) Ts/Tn. Is/In
Technical Data Two Speed Motor Single Winding Motor type 4 / 8 pole Power (kw) RPM In V (A) Power factor Cos ϕ Tn (Nm) Ts/Tn Is/In AC brake In (ma) DC brake In (ma) Z 0 (starts/ hour) Moment of inertia
More informationSeries VENTS KSK. Centrifugal kitchen fan in sound-insulated casing with air flow up to 8138 m 3 /h
SOUND-INSULATED KITCHEN FAN Series device. The impeller is mounted on the motor shaft and is balanced statically and dynamically. The motor has F class motor winding insulation and ingress protection rating.
More informationTAG3. Diesel engine - ElectropaK. Series kwm 1500 rpm. Basic technical data. Ratings. Total weight of ElectropaK
1105 kwm Standby @ 1500 rpm Diesel engine - ElectropaK 4000 Series Basic technical data Number of cylinders............................................................8 Cylinder arrangement................................................
More informationNEW ALTERNATIVE FUEL VEHICLE REGISTRATIONS IN THE EUROPEAN UNION 1 Q1 2015
NEW ALTERNATIVE FUEL VEHICLE REGISTRATIONS IN THE Q1 2015 ALTERNATIVE FUEL VEHICLE registrations: +28.8% in in first quarter In the first quarter of 2015, total alternative fuel vehicle (AFV) registrations
More information4016TAG1A 4016TAG2A. Series kwm 1500 rpm kwm 1500 rpm ElectropaK. Ratings. Basic technical data
4016TAG1A 1270-1741 kwm (Gross) @ 1500 rpm 1413-1937 kwm (Gross) @ 1500 rpm ElectropaK Basic technical data Number of cylinders...................................................16 Cylinder arrangement..........................................
More informationWe continously develop great professional potential of people in the region and their long-term experiences in the precise engineering.
PRODUCTION OF AHP HYDRAULIKA, a.s. is a private jointstock company with a history which reaches up to 1952; located in a heart of Europe in the central part of the Slovak republic, in Turčianske Teplice.
More informationPiston Pumps Series P2 / P3 Variable Displacement
Piston Pumps Series P2 / P3 Variable Displacement Catalogue HY11-2600/UK July 2003 Contents Series P2/P3 Description Technical information 3 Ordering code 4 Control options LA and LB 6 Control options
More informationHADI-Paste-(wet) Filling-Process
HADI-Paste-(wet) Filling-Process Semi-automatic equipment type RPM-N5 / RPM-6 and Fully automatic production-line type PRP-N1 General: This popular system is used on a worldwide basis by many of the technology
More informationNEW ALTERNATIVE FUEL VEHICLE REGISTRATIONS IN THE EUROPEAN UNION 1 Q2 2015
NEW ALTERNATIVE FUEL VEHICLE REGISTRATIONS IN THE Q2 2015 New alternative fuel vehicle (AFV) registrations in the EU by engine type Q2 2014 Q2 2015 Thousand units 70 60 50 40 30 20 10 0 EVs HEVs AFVs other
More informationDelivery Statistics. Second quarter 2015 EUROPEAN PULP AND PAPER INDUSTRY
Second quarter EUROPEAN PULP AND PAPER INDUSTRY INTRODUCTION 2 nd Quarter, Paper and board deliveries by CEPI countries were 45.9 million tonnes in the first half of, a small tonnage decrease on the same
More informationProduct Data Sheet ACi 4420 HHR
ACi 4420 HHR INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 4 3 Operating Data... 5 3.1 Operating Data - Electrical Interface - Input... 5 3.2 Electrical Operating Data... 5
More informationNGS. Dual-Magnet Float Switch. Pressure: up to 25 bar. Density: > 0.7 kg/dm 3. High switch capacity. Material: stainless steel 1.
Dual-Magnet Float Switch measuring monitoring analysing NGS Pressure: up to 5 bar O O Medium temperature: up to 50 C Density: > 0.7 kg/dm 3 High switch capacity O O Connection: square flange, DIN flange,
More informationCEPSPO(2017) November 2017 NATO UNCLASSIFIED. To : See recipients list (page 3)
06 November 2017 To : See recipients list (page 3) Subject : Infrastructure Call for bidders Call for bids No. 1 related to the supply, setting up and commissioning of high-voltage power supply units and
More information5-door FRS-ID: Year of production Legend. Version 4.3b / Opel Automobile GmbH. High strength zone
Ampera-e 5-door Legend Airbag Stored gas inflator Seat belt pretensioner Gas strut / Preloaded spring High strength zone High voltage power cable / component High voltage disconnect SRS control unit Battery
More informationEnergy-efficient Cast Iron Three Phase Induction Motors 50 Hz
Energyefficient Cast Iron Three Phase Induction Motors Hz IE 1 / www.pumpsgp.com IE / ENERGYEFFICIENT CAST IRON CONTENTS SPECIFICATIONS APPLICATIONS FEATURES AND BENEFITS BENEFITS OF ENERGY EFFICIENT MOTORS
More informationEfficiency index. Efficiency index average best. Efficiency index. Number of average mean
semester: 2, year 2007 EURO TOP TEN Market Monitoring 2nd Note Refrigerator freestanding EU nnum nnum in in kwh kwh Class (A, A+ or average average A++) Austria 84 200.8 23 29.5 72.2 A++ 459 belgium 83
More informationAXIAL FANS Catalogue CN0050C01 May 2008
ADTA AXIAL FANS Catalogue CN0050C01 May 2008 ADTA AXIAL FANS Catalogue CN0050C01 May 2008 Construction Specifications Impellers: Breezax aerfoil blades are available in four types of material: Glass Reinforced
More informationEmissions per capita and GDP
Emissions per capita and GDP (1990 -) CEIP Centre on Emission Inventories and Projections Emissions per capita and emissions per GDP were calculated for all years from 1990 to where data was available
More informationProduction of heat by type Terajoules
Production of heat by type Table Notes geo represents heat used directly for district heating, agriculture etc. without a commercial transaction taking place. Please refer to the Definitions Section on
More informationIN-LINE MIXED FLOW DUCT FANS MIXVENT-TD Fan Systems
IN-LINE MIXED FLOW DUCT FANS MIXVENT-TD Fan Systems MIXVENT TD / MIXVENT TD-T MIXVENT TDx2 ACCESSORIES Description Range Construction The MIXVENT system has been designed to compliment the MIXVENT-TD range
More informationRDR-UL. Constant flow regulators
Fans Air Handling Units Air Distribution Products Fire Safety Air Conditioning Air Curtains and Fan Heater Tunnel Fans RDR-UL Constant flow regulators 2 Air distribution products RDR-UL Description Systemair
More informationS E R I E S. Electric Motors
S E R I E S COMPANY PROFILE Established in 1965 in the town of Formigine, Motovario has grown to become one of the most important Italian and European manufacturers of gear units for industrial and civil
More informationJaw Couplings REK DCO
elastic for dynamic applications with curved jaws Features Compensation of axial, radial and angular misalignments Adsorbs vibrations Progressive torsion spring properties due to primarily pressurised
More informationNew Generation 1LE1/1PC1
New Generation LE/PC /2 Orientation /2 Overview /3 Benefits /4 Application /4 Technical specifications /5 Selection and ordering data /7 More information /8 General Line motors with shorter delivery time
More informationBREXIT AND THE AUTO INDUSTRY: FACTS AND FIGURES
BREXIT AND THE AUTO INDUSTRY: FACTS AND FIGURES GLOBAL TRADE European Union EU vehicle imports: Total value: 48,019 million Quantity: 3,640,975 units EU vehicle exports: Total value: 138,536 million Quantity:
More informationIE2 and IE3 THREE PHASE ASYNCHRONOUS ELECTRIC MOTORS PRODUCT CATALOGUE ELK
IE2 and IE3 THREE PHASE ASYNCHRONOUS ELECTRIC MOTORS PRODUCT CATALOGUE ELK 000-0616 PRODUCTION SITE AND PRODUCTION TECHNOLOGY ELK Motor has been founded by major shareholders of Yılmaz Redüktör A.Ş. as
More informationSTANDARD VERSION OF HIGH VOLTAGE MOTORS
AUSTRIA STANDARD VERSION OF HIGH VOLTAGE MOTORS The following pages contains the three phase squirrel cage high voltage induction motors in three different versions. a) Open drip-proof IP23 motors SCf
More informationMobile Hydraulics Solutions
Mobile Hydraulics Solutions Fan Drives Hydraulically Driven Lube Oil PTO Gear Pumps KP Asphalt Gear Pumps BTH 1 Mobile Hydraulics Solutions Content 2 Hydraulic motors KM 3-19 Fan drives 3 KM 1 space optimized
More informationDATA SHEET. Three Phase Induction Motor - Squirrel Cage. Customer : Product code : : W22 NEMA Premium Efficiency Three-Phase
DATA SHEET Frame Output Poles Frequency Rated voltage Rated current L. R. Amperes LRC No load current Rated speed Slip Rated torque Locked rotor torque Breakdown torque Insulation class Service factor
More informationGeneral Purpose Cast Iron Motors
General Purpose Cast Iron Motors Totally enclosed squirrel cage three phase low voltage motors, Sizes 71-355, 0.25 to 250 kw www.abb.com/motors&drives > Motors > Low voltage motors > General purpose motors
More informationProduction of heat by type Terajoules
Production of heat by type Table Notes geo represents heat used directly for district heating, agriculture etc. without a commercial transaction taking place. represents heat used for the production of
More informationLifting Instructions for 1336 PLUS and FORCE D Frame Drives
Installation Instructions Lifting Instructions for 1336 PLUS and FORCE D Frame Drives This publication will guide you through the steps needed to properly lift and mount the following drives: 1336 PLUS
More informationALLROUNDER 520 A. Distance between tie bars: x (520 x 520 mm) Clamping force: 165 tons Injection unit: 6.1 oz, 8.2 oz, 15.
Facts and figures ALLROUNDER 52 A Distance between tie bars: 2.47 x 2.47 (52 x 52 mm) Clamping force: 165 tons Injection unit: 6.1 oz, 8.2 oz, 15.3 oz www.arburg.com 52 A Machine dimensions 78.8 53.7 33.44
More informationData sheet. Page: 1 / 5. ETL GGSAV11D BKSBIE3 Inline pump. Operating data. Design
Data sheet Page: 1 / 5 Operating data Requested flow rate Operating data determined for maximum inlet pressure Requested developed head 15.00 m Pumped medium Ambient air temperature 20.0 C Fluid temperature
More informationA-L O C COOLING SYSTEM OLAER COOLERS. Olaer A-LOC with integrated circulation pump for industrial hydraulic systems
OLAER A-L O C COOLERS COOLING SYSTEM Olaer A-LOC with integrated circulation pump for Olaer A-LOC with integrated circulation pump for industrial hydraulic systems R OLAER A-LOC FOR OPTIMUM EFFICIENCY
More informationNEW PASSENGER CAR REGISTRATIONS BY ALTERNATIVE FUEL TYPE IN THE EUROPEAN UNION 1 Quarter
PRESS EMBARGO: NEW PASSENGER CAR REGISTRATIONS BY ALTERNATIVE FUEL TYPE IN THE EUROPEAN UNION 1 Quarter 3 2017 Alternative fuel vehicle registrations: +51.4% in third quarter of 2017 In the third quarter
More informationCentrifugal Pumps. 50Hz
SJ 50Hz Non-Submersible Pump Made of cast iron Bipolar/Direct coupling type SJ model Applications General water supply in buildings and apartments, etc Hot and cold water circulation Supply of industrial
More informationTHERMAL GENERATION PROJECTS
THERMAL GENERATION PROJECTS Client /Project Country Project Details Date Power Utility Pakistan Owner s Engineering review of Basic and Detailed Engineering Operation & Maintenance Service Provider Advisory
More informationALLROUNDER 720 H. Distance between tie bars: 720 x 720 mm Clamping force: 3200 kn Injection unit (according to EUROMAP): 1300, 2100, 3200
Facts and figures ALLROUNDER 72 H Distance between tie bars: 72 x 72 mm Clamping force: 32 kn Injection unit (according to EUROMAP): 13, 21, 32 www.arburg.com 72 H Machine dimensions 858 2198 max. 385
More information8210/ RIPP LOCK lock washer. Efficient and secure
8210/10.02 RIPP LOCK lock washer Efficient and secure RIPP LOCK lock washers RIPP LOCK lock washers ribbed on both sides 2 The system RIPP LOCK lock washers have radial ribs on both sides. The pitch angle
More informationTRANSMISSIONS. Mechanical Power Transmission
TRANSMISSIONS Mechanical Power Transmission Dunlop BTL Ltd European Distribution Centre MPT House Brunswick Road Cobbs Wood Industrial Estate Ashford, Kent. UK TN23 1EL Contact us +44 (0)1233 663340 +44
More informationSpain s exports by oil product group and country of destination. Year Corporación de Reservas Estratégicas de Productos Petrolíferos
Corporación de Reservas Estratégicas de Productos Petrolíferos Castellana, 79 28046 Madrid T. +34 91 360 09 10 Updated F. +34 91 420 on39 45 www.cores.es July 13 th 2015 Spain s exports by oil product
More informationSlide Bearings For Industrial, Marine And Offshore Installations
Slide Bearings For Industrial, Marine And Offshore Installations The advantages of working with RENK Hannover are many; here are a few of particular interest: RENK can boast a depth of experience in bearings
More informationCase studies on adoption of advanced coal-fired power technology in emerging economies
Case studies on adoption of advanced coal-fired power technology in emerging economies Cleaner and more efficient coal technologies in Russia Expert meeting 10 December 2012, World Trade Center, Moscow
More informationhore PRODUCT CATALOGUE nd Offsh arine an ms for Ma & Refrig CENTRIFUGAL FANS HV VAC &
hore nd Offsh arine an ms for Ma geration System & Refrig HV VAC & PRODUCT CATALOGUE CENTRIFUGAL FANS ! "# $ % & " ' (! ) * +,+( -../01..2 PRODUCT CATALOGUE 73-16 CENTRIFUGAL FANS CONTENT PAGE 1. CENTRIFUGAL
More informationPosition Qty. Description Single Price
Position Qty. Description Single Price 1 SEG.4.26.2.5B On request Product No.: 9675913 Note! Product picture may differ from actual product Grundfos SEG pumps are submersible pumps with horizontal discharge
More informationFacts and figures ALLROUNDER 1500 T
Facts and figures ALLROUNDER 15 T Table diameter: 59.6 (15 mm) Clamping force: 176, 22, 275, 35 tons : 3.7 oz, 6.1 oz, 8.2 oz, 15.3 oz, 29.1 oz, 45.4 oz www.arburg.com 15 T Machine dimensions up to 22
More informationALLROUNDER 320 C GOLDEN EDITION
Facts and figures ALLROUNDER 32 C GOLDEN EDITION Distance between tie bars: 12.6 x 12.6 (32 x 32 mm) Clamping force: 55 tons Injection unit: 2.3 oz, 3.7 oz www.arburg.com 32 C GOLDEN EDITION Machine dimensions
More informationALLROUNDER 630 H. Distance between tie bars: 630 x 630 mm Clamping force: 2500 kn Injection unit (acc. to EUROMAP): 800, 1300, 2100.
Facts and figures ALLROUNDER 63 H Distance between tie bars: 63 x 63 mm Clamping force: 25 kn Injection unit (acc. to EUROMAP): 8, 13, 21 www.arburg.com 63 H Machine dimensions 858 438 1468 2198 max. 395
More informationInfographics on Electromobility (January 2019)
Infographics on Electromobility (January 2019) Publisher: BMW Group Corporate Communications Electromobility Last Update: 04.01.2019 Contact: presse@bmw.de ELECTROMOBILITY IN GERMANY. SHARE IN NEW REGISTRATIONS
More informationMedium Voltage Soft Starters MOTOR CONTROL IS OUR NATURE
Medium Voltage Soft Starters MOTOR CONTROL IS OUR NATURE hrvs-dn General This advanced, micro-processor controlled through fiber optic links, Medium Voltage soft starter is designed for use with standard
More informationCentrifugal Fans ADH belt driven. Issue 2.5 EN August 2013
Centrifugal Fans ADH belt driven Issue 2.5 EN August 2013 1 AMCA Nicotra Gebhardt S.p.A. (Italy) certifies that ADH-E fans of the E0, E2, E4, E6 and E7 versions, from sizes 0160 to 0560, RDH-E fans of
More informationALLROUNDER 370 E. Distance between tie bars: 370 x 370 mm Clamping force: 600 kn Injection unit (acc. to EUROMAP): 170, 290.
Facts and figures ALLROUNDER 37 E Distance between tie bars: 37 x 37 mm Clamping force: 6 kn Injection unit (acc. to EUROMAP): 17, 29 www.arburg.com 37 E Machine dimensions 215 122 85 12 33 435 192 245
More informationLow Voltage Induction Motors
Low Voltage Induction Motors Catalogue-2009/04 E TAC-C CAST IRON Frame Size 71->355 0,18-315 kw t-telectric.com Technical features TAC-C motors are designed and manufactured according to IEC34, IEC72,
More informationALLROUNDER 520 E. Distance between tie bars: 520 x 520 mm Clamping force: 1500 kn Injection unit (acc. to EUROMAP): 290, 400, 800.
Facts and figures ALLROUNDER 52 E Distance between tie bars: 52 x 52 mm Clamping force: 15 kn Injection unit (acc. to EUROMAP): 29, 4, www.arburg.com 52 E Machine dimensions 2 135 85 12 33 4 13 625 4885
More informationproducts 22 º C Ventilation Air Conditioning Refrigeration Self Contained Units - 90MA self-contained marine air conditioning unit Inside
products > Self Contained Units - 90MA self-contained marine air conditioning unit OUTSIDE 35 C HUMIDITY 90% 22 º C Inside PROVIDED BY HEINEN & HOPMAN Heating Ventilation Air Conditioning Refrigeration
More informationA.C. Motor for Railway. Auxiliary Application
A.C. Motor for Railway Auxiliary Application EN A dynamic, strong and ambitious Group: Orange1 Holding is an international renown Group, one of the most important European manufacturers of single-phase
More informationALLROUNDER 570 H. Distance between tie bars: 570 x 570 mm Clamping force: 2000 kn Injection unit (acc. to EUROMAP): 400, 800, 1300.
Facts and figures ALLROUNDER 57 H Distance between tie bars: 57 x 57 mm Clamping force: 2 kn Injection unit (acc. to EUROMAP): 4, 8, 13 www.arburg.com 57 H Machine dimensions 22 148 85 438 2242 1) 2251
More informationALLROUNDER 630 A. Distance between tie bars: 630 x 630 mm Clamping force: 2500 kn Injection unit (acc. to EUROMAP): 800, 1300, 2100.
Facts and figures ALLROUNDER Distance between tie bars: 630 x 630 mm Clamping force: 2500 kn Injection unit (acc. to EUROMAP): 800, 1300, 2100 www.arburg.com Machine dimensions 2217 227 1487 max. 450 877
More informationNEW PASSENGER CAR REGISTRATIONS BY FUEL TYPE IN THE EUROPEAN UNION 1
PRESS EMBARGO: NEW PASSENGER CAR REGISTRATIONS BY FUEL TYPE IN THE EUROPEAN UNION 1 Quarter 3 2018 Fuel types of new cars: diesel 18.2%, petrol +15.2%, electric +30.0% in third quarter of 2018 In the third
More informationALLROUNDER 270 C GOLDEN EDITION
Facts and figures ALLROUNDER 2 C GOLDEN EDITION Distance between tie bars: 2 x 2 mm Clamping force: 4 kn Injection unit (acc. to EUROMAP):, 1 www.arburg.com 2 C GOLDEN EDITION Machine dimensions 85 33
More informationALLROUNDER 570 C GOLDEN EDITION
Facts and figures ALLROUNDER 57 C GOLDEN EDITION Distance between tie bars: 57 x 57 mm Clamping force: 2 kn Injection unit (acc. to EUROMAP): 8 www.arburg.com 57 C GOLDEN EDITION Machine dimensions 255
More information3 Phase Power Systems - Designed for Canada
3 Phase Power Systems - Designed for Canada AC OUTPUT NESS-25kVA - Mobile NESS-50kVA - Mobile Units Rated AC Power Output 33 66 kw Maximum AC Power Output 33 66 kw AC Output Line Connection 4 - wire (L1-L2-L3-N)
More informationALLROUNDER 630 S. Distance between tie bars: 630 x 630 mm Clamping force: 2500 kn Injection unit (acc. to EUROMAP): 800, 1300, 2100.
Facts and figures ALLROUNDER 630 S Distance between tie bars: 630 x 630 mm Clamping force: 2500 kn Injection unit (acc. to EUROMAP): 800, 1300, 2100 www.arburg.com 630 S Machine dimensions 2183 5) 2207
More informationALLROUNDER 270 A. Distance between tie bars: 270 x 270 mm Clamping force: 350 kn Injection unit (acc. to EUROMAP): 5, 70, 100.
Facts and figures ALLROUNDER 27 A Distance between tie bars: 27 x 27 mm Clamping force: 35 kn Injection unit (acc. to EUROMAP): 5, 7, 1 www.arburg.com 27 A Machine dimensions 238 122 12 425 254 438 191
More information