LIFT STATION 11 ONE-LINE DIAGRAM

Transcription

1 LAC JOB : OSG-D-ELEC06.DWG LIFT STATION 11 ONE-LINE DIAGRAM DWG : SHEET : E

2 NEW NEW GENERATOR PAD BOLLARD BOLLARD WETWELL ACCESS HATCH WETWELL OUTLINE HANDHOLE SEWER MANHOLE LIFT STATION 11 ELECTRICAL PLAN LIFT STATION YARD HYDRANT D HOTBOX MAIN SERVICE DISCONNECT, TO BE REPLACED. SEE DWG E18 FOR DETAIL. FIELD FIT CONDUIT RISERS UNDER ENCLOSURE LIGHT POLE MAIN CONTROL ENCLOSURE POWER DISTRIBUTION AND SIGNAL PLAN CONCRETE PAD BOLLARD NEW AUTOMATIC TRANSFER SWITCH, FOR DETAIL SEE DWG E17 B ELECTRICAL NOTES EDGE OF PAVED AREA 1. SEE DWG E17 FOR CONDUIT AND WIRE SCHEDULE. 2. CONTRACTOR SHALL COORDINATE WITH ELECTRICAL UTILITY TO DE-ENERGIZE ELECTRICAL SERVICE DURING SERVICE DISCONNECT SWITCH REPLACEMENT. ALL UTILITY COORDINATION AND COSTS SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR. LAC JOB : OSG-D-ELEC06.DWG DWG : SHEET : E

3 REMOVE MANUAL TRANSFER SWITCH LOCATED ON INTERIOR OF MAIN CONTROL CABINET UTILITY METER, TO BE REPLACED, SEE DWG NO E18 FOR DETAIL. 36" MIN. SERVICE ENTRANCE DISCONNECT SWITCH TO BE REMOVED AND REPLACED WITH NEW SWITCH. MODIFY OR REPLACE CONDUITS AND CONDUCTORS TO ACCOMMODATE THE NEW SWITCH. SEE DWG E18 FOR DETAIL. REMOVE GENERATOR RECEPTACLE. AND WIRING. PATCH PENETRATIONS WITH BOLTED 1/8 INCH TYPE 304 SS PLATE AS NECESSARY. INSTALL NEW CONDUCTORS IN CONDUIT SS UNISTRUT, TYP. UNISTRUT FOOTING, TYP. B 6'-0" LIFT STATION 11 GENERATOR AND ATS DIAGRAM GENERATOR AND ATS DIAGRAM ATS FED BY THE UTILITY DISCONNECT AND STATION FED BY THE UTILITY DISCONNECT AND UTILITY DISCONNECT TO THE RIGHT OF ENCLOSURE GENERATOR EMERGENCY STOP INSIDE GENERATOR DISCONNECT BREAKER INSIDE LAC JOB : OSG-D-ELEC06.DWG DWG : SHEET : E

4 6' MAX LIFT STATION 11 METER AND S.E.D. MODIFICATIONS DISCONNECT AND METER BASE LAYOUT NEW DISCONNECT AND METER BASE LAYOUT REROUTE CONDUCTORS: - REMOVE FEEDERS CONNECTED TO THE DISCONNECT. - EXTEND CONDUIT "S" - INSTALL NEW METER BASE (LOWER THAN THE METER BASE) AND RECONNECT TO THE NEW METER BASE - PLUG AND SEAL THE OLD PENETRATIONS USING TYPE 304 SS PLATE. SECURE PLATE AND MAKE WEATHERPROOF. METER AND S.E.D. MODIFICATIONS NOT TO SCALE LAC JOB : OSG-D-ELEC06.DWG DWG : SHEET : E

5 LAC JOB : OSG-D-ELEC07.DWG LIFT STATION 17 ONE-LINE DIAGRAM DWG : SHEET : E

6 CONTINUES TO UTILITY TRANSFORMER SEE DWG C10 FOR DETAIL HOTBOX HANDHOLE SECONDARY SERVICE CONDUIT, TO BE ABANDONED IN PLACE WATER METER HANDHOLE UNISTRUT SUPPORTS TELEMETRY PANEL MAIN SERVICE DISCONNECT, TO BE REMOVED ENCLOSURE YARD HYDRANT UTILITY METER, TO BE REMOVED NEW AUTOMATIC TRANSFER SWITCH MANUAL TRANSFER SWITCH, TO BE REMOVED D DRY WELL OUTLINE JUNCTION VAULT FIELD FIT CONDUIT RISERS UNDER NEW AND ENCLOSURES NEW UTILITY METER NEW MAIN SERVICE DISCONNECT NEW CONCRETE PAD EXTENSION. NEW UNISTRUT SUPPORT, FOR DETAIL SEE DWG E21 B NEW GENERATOR PAD NEW STANDBY GENERATOR ELECTRICAL NOTES 1. INTERCEPT CONDUIT FEEDING THE PUMP CONTROL PANEL IN DRY WELL ABOVE GRADE WITH NEW CONDUIT. INSTALL JUNCTION BOX TO MAKE CONNECTION. INSTALL NEW CONDUCTORS IN NEW AND CONDUIT. 2. SUPPORT NEW CONDUIT ON AND NEW UNISTRUT SUPPORT. 3. ROUTE CONDUIT ABOVE GRADE AND PENETRATE DRYWELL WALL 2 ABOVE GRADE. SEAL CONDUIT PENETRATION WATER TIGHT. 4. SEE DWG E21 FOR CONDUIT AND WIRE SCHEDULE. 5. CONTRACTOR SHALL COORDINATE WITH ELECTRICAL UTILITY TO DE-ENERGIZE ELECTRICAL SERVICE DURING SECONDARY POWER AND SERVICE DISCONNECT SWITCH REPLACEMENT. SECONDARY POWER CONDUIT SIZE, TYPE AND MATERIALS SHALL BE PER UTILITY STANDARDS. ALL UTILITY COORDINATION AND COSTS SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR. LIFT STATION 17 ELECTRICAL PLAN CONCRETE APRON LAC JOB : OSG-D-ELEC07.DWG POWER DISTRIBUTION AND SIGNAL PLAN DWG : SHEET : E

7 UTILITY METER ON REAR OF UNISTRUIT TO BE REMOVED MAXIMUM HEIGHT OF METER BASE SHALL BE 6"-0" ABOVE GRADE REMOVE MANUAL TRANSFER SWITCH AND GENERATOR RECEPTACLE ON REAR OF UNISTRUIT ENCLOSURE, DO NOT DISTURB TELEMETRY PANEL SERVICE ENTRANCE DISCONNECT SWITCH ON REAR OF UNISTRUT TO BE REMOVED. 7'-0" APPROX. 1-1/2" LR 1-1/2" PULLING ELL SS UNISTRUT, TYP. 1-1/2" LL 6'-0" NEW 6"X6" JUNCTION BOX CONDUITS CONTINUE TO BREAKER PANEL LOCATED IN DRY WELL CL2 ANALYZER PANEL LIFT STATION 17 GENERATOR AND ATS DIAGRAM ATS FED BY THE UTILITY DISCONNECT AND STATION FED BY THE UTILITY DISCONNECT AND UTILITY DISCONNECT B CONDUIT CONTINUES TO UTILITY TRANSFORMER UNISTRUT FOOTING, TYP. 3/4" PREMOLDED JOINT FILLER GENERATOR AND ATS DIAGRAM 3/4" PREMOLDED JOINT FILLER 3/4" PREMOLDED JOINT FILLER CONDUIT CONTINUES TO 2-INCH PVC PUMP CONTROL PANEL CONDUIT LOCATED IN DRY WELL LAC JOB : OSG-D-ELEC07.DWG GENERATOR EMERGENCY STOP INSIDE GENERATOR DISCONNECT BREAKER INSIDE DWG : SHEET : E

8 ɸ LAC JOB : OSG-D-ELEC08.DWG LIFT STATION 24 ONE-LINE DIAGRAM DWG : SHEET : E

9 BOLLARDS PVC RISER, TYP. NEW NEW GENERATOR PAD OUTLINE OF BELOW GRADE HOLDING TANK WETWELL ACCESS HATCH NEW AUTOMATIC TRANSFER SWITCH, FOR DETAIL SEE DWG E24 B JUNCTION BOX WETWELL OUTLINE MAIN SERVICE DISCONNECT, TO BE REPLACED. SEE DWG E25 FOR DETAIL. CONCRETE PAD BOLLARD LIFT STATION 24 ELECTRICAL PLAN STUBOUT CONDUIT 2 FEET BEYOND CONCRETE PAD AND STAKE FOR FUTURE USE. BOLLARD BOLLARD FIELD FIT CONDUIT RISERS UNDER ENCLOSURE D LAC JOB : OSG-D-ELEC08.DWG ELECTRICAL NOTES 1. SEE DWG E24 FOR CONDUIT AND WIRE SCHEDULE. 2. CONTRACTOR SHALL COORDINATE WITH ELECTRICAL UTILITY TO DE-ENERGIZE ELECTRICAL SERVICE DURING SERVICE DISCONNECT SWITCH REPLACEMENT. ALL UTILITY COORDINATION AND COSTS SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR. MAIN CONTROL PANEL POWER DISTRIBUTION AND SIGNAL PLAN UTILITY METER YARD HYDRANT HOTBOX DWG : SHEET : E

10 REMOVE MANUAL TRANSFER SWITCH LOCATED ON INTERIOR OF MAIN CONTROL CABINET UTILITY METER REMOVE GENERATOR RECEPTACLE. AND WIRING. PATCH PENETRATIONS WITH BOLTED 1/8 INCH TYPE 304 SS PLATE AS NECESSARY. 36" MIN. SERVICE ENTRANCE DISCONNECT SWITCH TO BE REMOVED AND REPLACED WITH NEW SWITCH. MODIFY OR REPLACE CONDUITS AND CONDUCTORS TO ACCOMMODATE THE NEW SWITCH. SS UNISTRUT, TYP. UNISTRUT FOOTING, TYP. B 6'-0" LIFT STATION 24 GENERATOR AND ATS DIAGRAM GENERATOR AND ATS DIAGRAM ATS FED BY THE UTILITY DISCONNECT AND STATION FED BY THE UTILITY DISCONNECT AND UTILITY DISCONNECT TO THE RIGHT OF ENCLOSURE GENERATOR EMERGENCY STOP INSIDE GENERATOR DISCONNECT BREAKER INSIDE LAC JOB : OSG-D-ELEC08.DWG DWG : SHEET : E

11 LAC JOB : OSG-D-ELEC08.DWG LIFT STATION 24 METER AND S.E.D. MODIFICATIONS DISCONNECT AND CONDUIT "R" LAYOUT NEW DISCONNECT AND NEW CONDUIT "R" LAYOUT - RE-USE 240V FEEDERS AND METER BASE - INSTALL NEW THE CONDUIT ( R ) AND CONDUCTORS BETWEEN THE METER BASE AND DISCONNECT - INSTALL NEW DISCONNECT S.E.D. AND CONDUIT MODIFICATIONS NOT TO SCALE DWG : SHEET : E

12 LAC JOB : OSG-D-ELEC09.DWG LIFT STATION 27 ONE-LINE DIAGRAM DWG : SHEET : E

13 NEW BOLLARD, TYP. LIGHT POLE EDGE OF ROADWAY JUNCTION BOX SALVAGED STANDBY GENERATOR NEW GENERATOR PAD JUNCTION BOX GENERATOR NAMEPLATE SALVAGED GENERATOR, PROVIDED BY CITY. TO BE INSTALLED ON NEW GENERATOR PAD. GENERATOR IS 115" LONG, 29" WIDE, 65" TALL. CONTRACTOR SHALL MOVE THE GENERATOR FROM ITS CURRENT LOCATION TO THE SITE. WETWELL ACCESS HATCH FIELD FIT CONDUIT RISERS UNDER ENCLOSURE NEW UTILITY METER D DESCRIPTION PLOT DATE: REVIEWED: DATE SAVE DATE: 1. SEE DWG E28 FOR CONDUIT AND WIRE SCHEDULE. 2. CONTRACTOR SHALL COORDINATE WITH ELECTRICAL UTILITY TO DE-ENERGIZE ELECTRICAL SERVICE DURING SERVICE DISCONNECT SWITCH REPLACEMENT. ALL UTILITY COORDINATION AND COSTS SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR. GENERATOR POWER DISTRIBUTION AND SIGNAL PLAN ELECTRICAL NOTES ENGINEER: PVC RISER, TYP. Apr 17, 2019 NEW AUTOMATIC TRANSFER SWITCH LAC MAIN CONTROL PANEL CONCRETE PAD OSG-D-ELEC09.DWG JOB : YARD HYDRANT BY REVIEW NEW SERVICE DISCONNECT LIFT STATION 27 ELECTRICAL PLAN WETWELL OUTLINE CITY CITY OF OF LACEY LACEY ON-SITE ON-SITE LIFT LIFT STATION STATION GENERATORS GENERATORS SITE FENCE 0" 1" DWG : SHEET : E " 47

14 NEW AUTOMATIC TRANSFER SWITCH LOCATED ON THE BACK OF THE MAIN CONTROL CABINET ENCLOSURE SERVICE ENTRANCE DISCONNECT SWITCH TO BE REMOVED AND REPLACED WITH NEW SWITCH. MODIFY OR REPLACE CONDUITS AND CONDUCTORS TO ACCOMMODATE THE NEW SWITCH. UTILITY METER BASE, TO BE REMOVED AND REPLACED WITH NEW UTILITY METER BASE. LAC JOB : LIFT STATION 27 GENERATOR AND ATS DIAGRAM GENERATOR AND ATS DIAGRAM ATS FED BY THE UTILITY DISCONNECT AND STATION FED BY THE UTILITY DISCONNECT AND UTILITY DISCONNECT TO THE RIGHT OF ENCLOSURE GENERATOR EMERGENCY STOP INSIDE GENERATOR DISCONNECT BREAKER INSIDE OSG-D-ELEC09.DWG DWG : SHEET : E

15 1-1/2" PULLING ELL 1-1/2" LL LIFT STATION 27 CONTROL PANEL MODIFICATION 1-1/2" LR 2-INCH CONDUIT CONTINUES TO UTILITY TRANSFORMER 2-INCH CONDUIT CONTINUES TO UTILITY TRANSFORMER 1-1/2" PULLING ELL LAC JOB : OSG-D-ELEC09.DWG CONTROL PANEL MODIFICATIONS DWG : SHEET : E