INTRODUCTION TO ENGINEERING COMPOUNDS FLAME RETARDANTS HIGH PERFORMANCE
|
|
- Molly Gibbs
- 5 years ago
- Views:
Transcription
1 INTRODUCTION TO ENGINEERING COMPOUNDS FLAME RETARDANTS HIGH PERFORMANCE
2 PRODUCTS ETP, FR, HPP LATI NOMENCLATURE NATURAL & COLOURED MINERAL FILLED GLASS BEADS GLASS FIBRES CARBON FIBRES ELASTOMER MODIFIED FLAME RETARDANT PEEK a a a a b High Performance PPS LARTON a a a b PPA a a a PPSU LAPEX R a a b PES LAPEX A a a b PSU LASULF a a b PPh/PPc / EP a a a a a PA6 6 a a a a a a PA6 KELON B a a a Semi - crystallines PA66 66 a a a a a a PA66 KELON A a a a PAc 68 a a PAc SP a a a a a a a PA12 12 a a a a PBT LATER a a a a a a a POM LATAN a a a a a ABS LASTILAC a a a a Amorphous SAN LASTIL a a PC LATILON a a a a PPOm LARIL a a a PUR LASTANE a a ABS/PC LASTILAC 10 a a Blends PBT/PC LATIBLEND a a a a PBT/ABS LATIBLEND a a a PA/PP LATIBLEND a a b Intrinsically self-extinguishing
3 WHO IS LATI? LATI was created in Italy in From the year of foundation untill today, Lati has gained an absolutely prestigious position in the production of technical thermoplastic compounds. Nowadays Lati is: the compounder with the largest range of technical thermoplastics in Europe; one of the most qualified self-extinguishing compounds suppliers in the world; the most important independent European producer of fit-for-use thermoplastic compounds for special applications. The company has two plants in the North of Italy with a potential capacity of 38,000 tonnes per year. LATI s products are suitable for use in several industrial segments, from the automotive to fine mechanics, from domestic appliances to electronics. The distribution of materials is guaranteed by its own export network. The mission of LATI is to guarantee complete satisfaction to the customer thanks to the high technical contents of its own products and services, keeping maximum flexibility towards market requirements with a constant quality level.
4 ....
5 PROPERTIES (typical values) Latest updates on: FEATURES Physical Testing conditions Norms Units (SI) Density 23 C ISO 1183 g/cm³ Linear shrinkage at moulding * longitudinal 2mm thickness - packing pressure: 60MPa transversal ISO % Moisture absorption after 24h ISO 62 % Mechanical Notched IZOD (sample 63.5 x 12.7 x 3.2 mm) Notched CHARPY (sample 80 x 10 x 4 mm) Unnotched CHARPY (sample 80 x 10 x 4 mm) Tensile elastic modulus (speed 1 mm/min) Tensile strength (at yield) (speed 5 mm/min) Tensile strength (at break) (speed 5 mm/min) Tensile elongation (at yield) (speed 5 mm/min) Tensile elongation (at break) (speed 5 mm/min) 23 C -20 C 23 C -20 C 23 C -20 C 23 C 60 C 90 C 120 C 150 C 23 C 60 C 90 C 120 C 150 C 23 C 60 C 90 C 120 C 150 C 23 C 60 C 90 C 120 C 150 C 23 C 60 C 90 C 120 C 150 C ASTM D256-A J/m ISO 179-1eA kj/m 2 ISO 179-1eU kj/m 2 ISO R 527 (1) ISO 527 (1) ISO 527 (1) MPa MPa MPa ISO 527 (1) % ISO 527 (1) % Thermal Coefficient of linear thermal expansion 20 C 100 C LATI x10-6/ C Continuous Use Temperature (C.U.T.) continuous h IEC 216 C Vicat - Softening point 49 N - 50 C/h IS06 C HDT Heat Deflection Temperature 0.45 MPa 1.82 MPa ISO 75 C Electrical Electrical resistivity (surface) ASTM D 257 ohm CTI - Comparative Tracking Index IEC 112 V Flammability 3 mm Flammability rating 1.5 mm 0.75 mm UL 94 class GWFI - Glow Wire Flammability Index 2 mm 1 mm IEC C GWIT - Glow Wire Ignition Test 2 mm 1 mm IEC C Processing conditions Pre-drying temperature (at least 3 hours...) C Melt temperature C Mould Temperature C a b c d e f g h i j k l m Low smoke density and low toxicity index Low thermal expansion coefficient Electrically conductive High stiffness Halogen free Red phosphorous free PBB/PBDE free Very good surface appearance Very good impact resistance Very good chemical resistance Very high dimensional stability Very good thermal properties Tribological properties
6 ENGINEERING THERMOPLASTICS PA 66 PA 6 PA 6 PA 6 PPOm PPOm PUR PUR SAN ABS/PC ABS/PC ABS ABS PA 12 KELON A H CEG/40 KELON B H CER/30 KELON B H CET/30 KELON B H CETG/300 LARIL 13 G/20 LARIL 13 G/30 LASTANE 50 LASTANE 50 G/25 LASTIL G/30 LASTILAC 10 LASTILAC 11 G/10 LASTILAC RT K/10 LASTILAC SP G/17 12 CP/85 k k b b ik bi k hi k hi k b NB NB NB NB NB NB NB E HB HB HB HB HB HB AF PBB/PBDE and Sb 2 free HF Halogen free AG Chemically coupled K Carbon fibre B High fluidity KB, KB1 Red phosphorous C High viscosity KB3 Red phosphorous, suitable for warm & humid environments CE, CER, CET, KC, MX, TR, T, TES Mineral filler KB4 Red phosphorous. V0 at 0.75mm thickness. Improved CTI CP Special mineral filler L Oil stabilisation CT1 Improved CTI S Glass beads CT2 PBB/PBDE. Low Sb 2 content UV UV stabilisation CT3 Improved CTI. Halogen and red phosphorous free V Flame retardant CT4 Improved CTI. Low smoke density and low toxicity index VH Glycol and hydrolisis stabilisation E, PX Improved impact resistance V0, V1, V2 UL94-V0, V1, V2 FE Magnetizable filler W Metal stabilisation G Glass fibres V0E PBB/PBDE free H, H2, VH2 Heat stabilisation ---- UL approved
7 ENGINEERING THERMOPLASTICS PA 12 PA 12 PA 12 PA 12 PA 6 PA 6 PA 6 PA 6 PA 6 PA 6 PA 6 PA 6 PA 6 PA H FE90 12 H2 G/30 12 H2 K/30 12 G/50 6 BH 6 CUVHPX10 G/35 6 E02 6 H2 G/30 6 H2 G/35 6 H2 G/50 6 H2 G/55 6 H2E04 G/30 bi bc bi hk ik i bi bi i hk hk 6 S/ NB 60 NB NB NB 63 NB NB NB NB 105 NB NB NB 80 NB NB NB 65 NB NB NB 55 NB NB NB NB 5.5 NB NB NB 6 NB NB NB 6 NB NB NB 6 NB NB HB V-2 V-2 HB HB V-2 HB V-2 V-2 HB HB HB V-2 V-2 HB HB * Values obtained according to ISO norm at the specified pressure. Actual shrinkage values may differ because of the design. Values shown are based on testing of injection moulded laboratory test specimens, conditioned according to the practice and represent data that fall within the standard range of properties for non-coloured material, if not otherwise specified. As they may be subject to variations, these values do not represent a sufficient basis for any part design and are not intended for use in establishing values for specification purposes. Properties of moulded parts can be influenced by a wide range of factors including, but not limited to, colorants, part design, processing conditions, post-treatment conditions, environmental conditions and usage of regrind during the moulding process. If data are explicitely indicated as provisional, range of properties has to be considered wider. This information and technical assistance are provided as a convenience for informational purposes only and are subject to change without notice. The customer shall always ensure that the latest release of technical information is at his own disposal. Lati S.p.A. extends no warranties or guarantee, including a warranty of merchantability of whatever use is made of the product, and make no representations as to the accuracy, suitability, reliability, completeness and sufficiency of the information provided, and assume no responsibility regarding the consequences of its use or for any printing errors. It is the customer s responsibility to inspect and test our products in order to determine to his own satisfaction whether they are suitable for his intended uses and applications or used in conjunction with third-party materials This application-specific analysis shall at least include preliminary testing to determine the suitability for the customer s particular purpose from a technical as well as health, safety, and environmental standpoint. Such testing has not necessarily been done by us as the manner in which the customer use and the purpose to which utilise our products are beyond our control. Lati S.p.A. does not accept and hereby disclaims liability for, any damages whatsoever in connection with the use of or reliance on this information. No one is authorised to make any warranties, issue any immunities or assume any liabilities on behalf of Lati S.p.A. except in a writing signed by a specifically authorised Lati S.p.A. executive. Unless otherwise agreed in writing, the exclusive remedy for all claims is replacement of the product or refund of the purchase price at Lati s option, and in no event shall Lati S.p.A. be liable for special, consequential, incidental, punitive or exemplary damages. No information herein can be considered as a suggestion to use any product in conflict with intellectual property rights of third-parties. Lati S.p.A. disclaims any liability that may be claimed for infringement or alleged infringement of patents. Unless specifically stated in writing, the products mentioned herein are not suitable for applications in the pharmaceutical, medical or dental sector, in contact with foodstuff or for potable water transportation. For any other issues Lati S.p.A. Conditions of Sales apply. Copyright LATI S.p.A. 2010
8 ENGINEERING THERMOPLASTICS PA 66 PA 66 PA 66 PA 66 PA 66 PA 66 PA 66 PA 66 PA 66 PA 66 PA 66 PA 66 PA E21 66 E21 G/15 66 E21 G/30 66 E21 K/30 66 H2 G/25 66 H2 G/30 66 H2 G/35 66 H2 G/50 66 H2 G/60 66 H2 K/20 66 H2 K/30 ik i i bci i bi bi bi bc bc d 66 H2 K/40 bc d 66 H2 K/50 bc di NB NB NB NB NB NB NB NB NB NB NB NB NB E3 HB HB HB HB HB HB HB AF PBB/PBDE and Sb 2 free HF Halogen free AG Chemically coupled K Carbon fibre B High fluidity KB, KB1 Red phosphorous C High viscosity KB3 Red phosphorous, suitable for warm & humid environments CE, CER, CET, KC, MX, TR, T, TES Mineral filler KB4 Red phosphorous. V0 at 0.75mm thickness. Improved CTI CP Special mineral filler L Oil stabilisation CT1 Improved CTI S Glass beads CT2 PBB/PBDE. Low Sb 2 content UV UV stabilisation CT3 Improved CTI. Halogen and red phosphorous free V Flame retardant CT4 Improved CTI. Low smoke density and low toxicity index VH Glycol and hydrolisis stabilisation E, PX Improved impact resistance V0, V1, V2 UL94-V0, V1, V2 FE Magnetizable filler W Metal stabilisation G Glass fibres V0E PBB/PBDE free H, H2, VH2 Heat stabilisation ---- UL approved
9 ENGINEERING THERMOPLASTICS PA 66 PA 66 PA 66 PA 66 PA 66 PA6.10 PA6.10 PA6.12 PA6.12 POM POM POM POM POM 66 H2 S/30 66 H2E21 G/13 66 LH2 G/35 66 VH G/30 66 VH2 G/30 SP1 G/30 SP1 G/50 SP2 H2 G/35 SP2 H2 G/45 LATAN 13 LATAN 13 G/30 LATAN 13 K/30 LATAN 13 S/15 LATAN 13 S/20 hk i j j m bc NB NB NB NB NB NB NB NB NB NB HB HB HB * Values obtained according to ISO norm at the specified pressure. Actual shrinkage values may differ because of the design. Values shown are based on testing of injection moulded laboratory test specimens, conditioned according to the practice and represent data that fall within the standard range of properties for non-coloured material, if not otherwise specified. As they may be subject to variations, these values do not represent a sufficient basis for any part design and are not intended for use in establishing values for specification purposes. Properties of moulded parts can be influenced by a wide range of factors including, but not limited to, colorants, part design, processing conditions, post-treatment conditions, environmental conditions and usage of regrind during the moulding process. If data are explicitely indicated as provisional, range of properties has to be considered wider. This information and technical assistance are provided as a convenience for informational purposes only and are subject to change without notice. The customer shall always ensure that the latest release of technical information is at his own disposal. Lati S.p.A. extends no warranties or guarantee, including a warranty of merchantability of whatever use is made of the product, and make no representations as to the accuracy, suitability, reliability, completeness and sufficiency of the information provided, and assume no responsibility regarding the consequences of its use or for any printing errors. It is the customer s responsibility to inspect and test our products in order to determine to his own satisfaction whether they are suitable for his intended uses and applications or used in conjunction with third-party materials This application-specific analysis shall at least include preliminary testing to determine the suitability for the customer s particular purpose from a technical as well as health, safety, and environmental standpoint. Such testing has not necessarily been done by us as the manner in which the customer use and the purpose to which utilise our products are beyond our control. Lati S.p.A. does not accept and hereby disclaims liability for, any damages whatsoever in connection with the use of or reliance on this information. No one is authorised to make any warranties, issue any immunities or assume any liabilities on behalf of Lati S.p.A. except in a writing signed by a specifically authorised Lati S.p.A. executive. Unless otherwise agreed in writing, the exclusive remedy for all claims is replacement of the product or refund of the purchase price at Lati s option, and in no event shall Lati S.p.A. be liable for special, consequential, incidental, punitive or exemplary damages. No information herein can be considered as a suggestion to use any product in conflict with intellectual property rights of third-parties. Lati S.p.A. disclaims any liability that may be claimed for infringement or alleged infringement of patents. Unless specifically stated in writing, the products mentioned herein are not suitable for applications in the pharmaceutical, medical or dental sector, in contact with foodstuff or for potable water transportation. For any other issues Lati S.p.A. Conditions of Sales apply. Copyright LATI S.p.A. 2010
10 ENGINEERING THERMOPLASTICS POM POM POM POM POM POM PPh PPh PPh PPh PPh PPh PPh PPc LATAN 13 S/30 LATAN 13 E71 LATAN 2 LATAN 23UV LATAN 23UVE71 LATAN 3 E71 22H2 MX/25 7H2W TR/40 9H TES/30 AG7H G/30 AG7H K/30 AG7H2 G/50 AG9H MI/40 EP 22UVH2 MX/25 i m m i hk k k bc b k hk NB NB NB NB NB NB 25 NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB 65 NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB HB HB HB HB HB HB AF PBB/PBDE and Sb 2 free HF Halogen free AG Chemically coupled K Carbon fibre B High fluidity KB, KB1 Red phosphorous C High viscosity KB3 Red phosphorous, suitable for warm & humid environments CE, CER, CET, KC, MX, TR, T, TES Mineral filler KB4 Red phosphorous. V0 at 0.75mm thickness. Improved CTI CP Special mineral filler L Oil stabilisation CT1 Improved CTI S Glass beads CT2 PBB/PBDE. Low Sb 2 content UV UV stabilisation CT3 Improved CTI. Halogen and red phosphorous free V Flame retardant CT4 Improved CTI. Low smoke density and low toxicity index VH Glycol and hydrolisis stabilisation E, PX Improved impact resistance V0, V1, V2 UL94-V0, V1, V2 FE Magnetizable filler W Metal stabilisation G Glass fibres V0E PBB/PBDE free H, H2, VH2 Heat stabilisation ---- UL approved
11 ENGINEERING THERMOPLASTICS PPc PBT PBT PBT PBT PBT ABS PPh PA 6 PC PC PC PC PC EP 7 TES/30 LATER 4 LATER 4 E61 LATER 4 G/20 LATER 4 G/30 LATER 4 G/50 LATIBLEND 3675 G/10 LATIBLEND 5262 LATIBLEND 6252 H2 G/30 k hk i b b i b LATILON 28D LATILON 28D G/20 LATILON 28D G/30 LATILON 28D K/20 ai k ak ak ab c LATILON 28D K/40 ab c NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB HB HB HB HB V-1 V-1 HB HB HB * Values obtained according to ISO norm at the specified pressure. Actual shrinkage values may differ because of the design. Values shown are based on testing of injection moulded laboratory test specimens, conditioned according to the practice and represent data that fall within the standard range of properties for non-coloured material, if not otherwise specified. As they may be subject to variations, these values do not represent a sufficient basis for any part design and are not intended for use in establishing values for specification purposes. Properties of moulded parts can be influenced by a wide range of factors including, but not limited to, colorants, part design, processing conditions, post-treatment conditions, environmental conditions and usage of regrind during the moulding process. If data are explicitely indicated as provisional, range of properties has to be considered wider. This information and technical assistance are provided as a convenience for informational purposes only and are subject to change without notice. The customer shall always ensure that the latest release of technical information is at his own disposal. Lati S.p.A. extends no warranties or guarantee, including a warranty of merchantability of whatever use is made of the product, and make no representations as to the accuracy, suitability, reliability, completeness and sufficiency of the information provided, and assume no responsibility regarding the consequences of its use or for any printing errors. It is the customer s responsibility to inspect and test our products in order to determine to his own satisfaction whether they are suitable for his intended uses and applications or used in conjunction with third-party materials This application-specific analysis shall at least include preliminary testing to determine the suitability for the customer s particular purpose from a technical as well as health, safety, and environmental standpoint. Such testing has not necessarily been done by us as the manner in which the customer use and the purpose to which utilise our products are beyond our control. Lati S.p.A. does not accept and hereby disclaims liability for, any damages whatsoever in connection with the use of or reliance on this information. No one is authorised to make any warranties, issue any immunities or assume any liabilities on behalf of Lati S.p.A. except in a writing signed by a specifically authorised Lati S.p.A. executive. Unless otherwise agreed in writing, the exclusive remedy for all claims is replacement of the product or refund of the purchase price at Lati s option, and in no event shall Lati S.p.A. be liable for special, consequential, incidental, punitive or exemplary damages. No information herein can be considered as a suggestion to use any product in conflict with intellectual property rights of third-parties. Lati S.p.A. disclaims any liability that may be claimed for infringement or alleged infringement of patents. Unless specifically stated in writing, the products mentioned herein are not suitable for applications in the pharmaceutical, medical or dental sector, in contact with foodstuff or for potable water transportation. For any other issues Lati S.p.A. Conditions of Sales apply. Copyright LATI S.p.A. 2010
12 FLAME RETARDANT PA 66 PA 66 PA 6 PA 6 PA 6 PA 6 PA 6 PPA PPA PPA PPOm PPOm PPOm PPOm SAN KELON A FR H2 CETG/300-V0 KELON A FR H CET/35-V2 KELON B FR H CET/05-V2HF KELON B FR H CET/30-V0 KELON B FR H CETG/250-V0 KELON B FR H2 CE/25-V2HF KELON B FR H2 CEG/500-V0CT3 fg fg fg fg fg e b D G/30-V0 bf gl D G/35-V0 bf gl D G/35-V0KB LARIL 13 G/10-V1 bl be f LARIL 13 G/20-V1 be f LARIL 13 G/30-V1 be f LARIL 13-V1KC be fk LASTIL G/25-V0 fk NB NB NB NB NB NB NB NB V-0 V-2 V-0 V-0 V-2 V-0 V-0 V-0 V-0 V-1 V-0 V-2 V-0 V-0 V-2 V-0 V-0 V-0 V-0 V-1 V-1 V-1 V-1 V-0 V-0 V-2 V-2 V-2 V-0 V-2 V-1 V-0 V-0 V AF PBB/PBDE and Sb 2 free HF Halogen free AG Chemically coupled K Carbon fibre B High fluidity KB, KB1 Red phosphorous C High viscosity KB3 Red phosphorous, suitable for warm & humid environments CE, CER, CET, KC, MX, TR, T, TES Mineral filler KB4 Red phosphorous. V0 at 0.75mm thickness. Improved CTI CP Special mineral filler L Oil stabilisation CT1 Improved CTI S Glass beads CT2 PBB/PBDE. Low Sb 2 content UV UV stabilisation CT3 Improved CTI. Halogen and red phosphorous free V Flame retardant CT4 Improved CTI. Low smoke density and low toxicity index VH Glycol and hydrolisis stabilisation E, PX Improved impact resistance V0, V1, V2 UL94-V0, V1, V2 FE Magnetizable filler W Metal stabilisation G Glass fibres V0E PBB/PBDE free H, H2, VH2 Heat stabilisation ---- UL approved
13 FLAME RETARDANT ABS ABS ABS PA 6 PA 6 PA 6 PA 6 PA 6 PA 6 PA 6 PA 6 PA 66 PA 66 PA 66 PA 66 LASTILAC AR G/17-V0E ef gk LASTILAC ARUV-V0 LASTILAC AR-V0E hk lf gk 6 H2 G/20-V0 6 H2 G/20- V2HF 6 H2 G/30- V0AF 6 H2 G/30- V0CT1 6 H2 G/30- V0HF1 6 H2 G/30- V2HF 6 H2PX-V0 6 H-V0 g gk ef hk 66 B G/20-V 66 B H-V0 66 H2 G/25-V0CT1 66 H2 G/25-V0HF1 eg ef hk b b NB NB 60 NB NB NB 50 NB NB NB 40 NB NB NB 5 NB NB NB 5.3 NB NB NB 6 NB V-0 5VA V-0 V-0 V-2 V-0 V-0 V-0 V-2 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-2 V-0 V-0 V-0 V-2 V-0 V-0 V-0 V-0 V-0 V-0 V-1 V-2 V-2 V-2 V-0 V-0 V-2 V-0 V-0 V-0 V-0 V-0 V * Values obtained according to ISO norm at the specified pressure. Actual shrinkage values may differ because of the design. Values shown are based on testing of injection moulded laboratory test specimens, conditioned according to the practice and represent data that fall within the standard range of properties for non-coloured material, if not otherwise specified. As they may be subject to variations, these values do not represent a sufficient basis for any part design and are not intended for use in establishing values for specification purposes. Properties of moulded parts can be influenced by a wide range of factors including, but not limited to, colorants, part design, processing conditions, post-treatment conditions, environmental conditions and usage of regrind during the moulding process. If data are explicitely indicated as provisional, range of properties has to be considered wider. This information and technical assistance are provided as a convenience for informational purposes only and are subject to change without notice. The customer shall always ensure that the latest release of technical information is at his own disposal. Lati S.p.A. extends no warranties or guarantee, including a warranty of merchantability of whatever use is made of the product, and make no representations as to the accuracy, suitability, reliability, completeness and sufficiency of the information provided, and assume no responsibility regarding the consequences of its use or for any printing errors. It is the customer s responsibility to inspect and test our products in order to determine to his own satisfaction whether they are suitable for his intended uses and applications or used in conjunction with third-party materials This application-specific analysis shall at least include preliminary testing to determine the suitability for the customer s particular purpose from a technical as well as health, safety, and environmental standpoint. Such testing has not necessarily been done by us as the manner in which the customer use and the purpose to which utilise our products are beyond our control. Lati S.p.A. does not accept and hereby disclaims liability for, any damages whatsoever in connection with the use of or reliance on this information. No one is authorised to make any warranties, issue any immunities or assume any liabilities on behalf of Lati S.p.A. except in a writing signed by a specifically authorised Lati S.p.A. executive. Unless otherwise agreed in writing, the exclusive remedy for all claims is replacement of the product or refund of the purchase price at Lati s option, and in no event shall Lati S.p.A. be liable for special, consequential, incidental, punitive or exemplary damages. No information herein can be considered as a suggestion to use any product in conflict with intellectual property rights of third-parties. Lati S.p.A. disclaims any liability that may be claimed for infringement or alleged infringement of patents. Unless specifically stated in writing, the products mentioned herein are not suitable for applications in the pharmaceutical, medical or dental sector, in contact with foodstuff or for potable water transportation. For any other issues Lati S.p.A. Conditions of Sales apply. Copyright LATI S.p.A. 2010
14 FLAME RETARDANT PA 66 PA 66 PA 66 PA 66 PA 66 PA 66 PA 66 PA 66 PA 66 PA 66 PA 66 PA6/PA66 PPh PPh PPh 66 H2 G/25-V0KB 66 H2 G/25-V0KB1 66 H2 G/25-V0KB3 66 H2 G/25-V0KB4 66 H2 G/35-V0KB 66 H2 G/35-V0KB1 66 H2 G/35-V0KB3 66 H2 G/50-V0KB1 66 H2PX-V0 66 H2PX-V2 66 H-V0 b b i b b b bi gk gk ef hk 68 H2-V0 ef k 7 TR-V2 7H2-V2HF 7H2W T-V0 k k k NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-2 V-0 V-0 V-2 V-2 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-2 V-0 V-0 V-2 V-2 V-0 V-0 HB HB V-0 V-0 HB V-0 V-0 V-0 V-2 V-0 V-2 V-2 V AF PBB/PBDE and Sb 2 free HF Halogen free AG Chemically coupled K Carbon fibre B High fluidity KB, KB1 Red phosphorous C High viscosity KB3 Red phosphorous, suitable for warm & humid environments CE, CER, CET, KC, MX, TR, T, TES Mineral filler KB4 Red phosphorous. V0 at 0.75mm thickness. Improved CTI CP Special mineral filler L Oil stabilisation CT1 Improved CTI S Glass beads CT2 PBB/PBDE. Low Sb 2 content UV UV stabilisation CT3 Improved CTI. Halogen and red phosphorous free V Flame retardant CT4 Improved CTI. Low smoke density and low toxicity index VH Glycol and hydrolisis stabilisation E, PX Improved impact resistance V0, V1, V2 UL94-V0, V1, V2 FE Magnetizable filler W Metal stabilisation G Glass fibres V0E PBB/PBDE free H, H2, VH2 Heat stabilisation ---- UL approved
15 FLAME RETARDANT PPh PPh PPh PPh PPh PPc PBT PBT PBT PBT PBT PC PC PC PC 7H2W T-V0E g 7H2W-V0 7-V2 AG3H2W G/30-V0 AG3H2W G/30-V0E EP 7-V2 LATER 4 E61 GCER/450-V0 LATER 4 G/30-V0 LATER 4 G/30-V0CT2 LATER 4-V0 LATIBLEND 7587 E61-V0 LATILON 28D-V0 LATILON 28D G/20-V0 ef k k b g k i g f bi ef ik k aef ik LATILON 30D-V0 LATILON 30D G/10-V ae fk NB NB NB NB 40 NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB 1.5 NB NB NB NB NB 1.5 NB NB NB VB V-0 V-2 5VA V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-2 V-0 V-0 V-2 V-0 V-0 V-0 V-0 V-0 V-2 V-0 V-0 V-0 V-0 V-2 V-0 V-0 V-0 V-0 V-0 V-2 V-2 V * Values obtained according to ISO norm at the specified pressure. Actual shrinkage values may differ because of the design. Values shown are based on testing of injection moulded laboratory test specimens, conditioned according to the practice and represent data that fall within the standard range of properties for non-coloured material, if not otherwise specified. As they may be subject to variations, these values do not represent a sufficient basis for any part design and are not intended for use in establishing values for specification purposes. Properties of moulded parts can be influenced by a wide range of factors including, but not limited to, colorants, part design, processing conditions, post-treatment conditions, environmental conditions and usage of regrind during the moulding process. If data are explicitely indicated as provisional, range of properties has to be considered wider. This information and technical assistance are provided as a convenience for informational purposes only and are subject to change without notice. The customer shall always ensure that the latest release of technical information is at his own disposal. Lati S.p.A. extends no warranties or guarantee, including a warranty of merchantability of whatever use is made of the product, and make no representations as to the accuracy, suitability, reliability, completeness and sufficiency of the information provided, and assume no responsibility regarding the consequences of its use or for any printing errors. It is the customer s responsibility to inspect and test our products in order to determine to his own satisfaction whether they are suitable for his intended uses and applications or used in conjunction with third-party materials This application-specific analysis shall at least include preliminary testing to determine the suitability for the customer s particular purpose from a technical as well as health, safety, and environmental standpoint. Such testing has not necessarily been done by us as the manner in which the customer use and the purpose to which utilise our products are beyond our control. Lati S.p.A. does not accept and hereby disclaims liability for, any damages whatsoever in connection with the use of or reliance on this information. No one is authorised to make any warranties, issue any immunities or assume any liabilities on behalf of Lati S.p.A. except in a writing signed by a specifically authorised Lati S.p.A. executive. Unless otherwise agreed in writing, the exclusive remedy for all claims is replacement of the product or refund of the purchase price at Lati s option, and in no event shall Lati S.p.A. be liable for special, consequential, incidental, punitive or exemplary damages. No information herein can be considered as a suggestion to use any product in conflict with intellectual property rights of third-parties. Lati S.p.A. disclaims any liability that may be claimed for infringement or alleged infringement of patents. Unless specifically stated in writing, the products mentioned herein are not suitable for applications in the pharmaceutical, medical or dental sector, in contact with foodstuff or for potable water transportation. For any other issues Lati S.p.A. Conditions of Sales apply. Copyright LATI S.p.A. 2010
16 HIGH PERFORMANCE THERMOPLASTICS PES PES PES PES PPSU PPSU PPSU PPA PPA PPA PPA PPA LAPEX A LAPEX A G/10 LAPEX A G/20 LAPEX A G/30 LAPEX R LAPEX R G/10 LAPEX R G/20 CE/60 G/15 G/30 G/35 G/45 abh kl abh kl ab l ab l abhi jkl abhi jkl abi jl bl l bl bl bl NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB NB V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V AF PBB/PBDE and Sb 2 free HF Halogen free AG Chemically coupled K Carbon fibre B High fluidity KB, KB1 Red phosphorous C High viscosity KB3 Red phosphorous, suitable for warm & humid environments CE, CER, CET, KC, MX, TR, T, TES Mineral filler KB4 Red phosphorous. V0 at 0.75mm thickness. Improved CTI CP Special mineral filler L Oil stabilisation CT1 Improved CTI S Glass beads CT2 PBB/PBDE. Low Sb 2 content UV UV stabilisation CT3 Improved CTI. Halogen and red phosphorous free V Flame retardant CT4 Improved CTI. Low smoke density and low toxicity index VH Glycol and hydrolisis stabilisation E, PX Improved impact resistance V0, V1, V2 UL94-V0, V1, V2 FE Magnetizable filler W Metal stabilisation G Glass fibres V0E PBB/PBDE free H, H2, VH2 Heat stabilisation ---- UL approved
17 HIGH PERFORMANCE THERMOPLASTICS PPA PPA PPA PPA PEEK PEEK PEEK PEEK PEEK PEEK D G/40 D G/50 D GCE/650 D K/ GCE/ G/15 10 G/30 10 G/40 10 G/50 bi l bi l bd l bc dl ajk lm abj klm aj lm aj lm aij lm abj lm NB NB >300 >300 >300 >300 >300 > > >300 > > > V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-1 V-0 V-1 V-1 V-1 V * Values obtained according to ISO norm at the specified pressure. Actual shrinkage values may differ because of the design. Values shown are based on testing of injection moulded laboratory test specimens, conditioned according to the practice and represent data that fall within the standard range of properties for non-coloured material, if not otherwise specified. As they may be subject to variations, these values do not represent a sufficient basis for any part design and are not intended for use in establishing values for specification purposes. Properties of moulded parts can be influenced by a wide range of factors including, but not limited to, colorants, part design, processing conditions, post-treatment conditions, environmental conditions and usage of regrind during the moulding process. If data are explicitely indicated as provisional, range of properties has to be considered wider. This information and technical assistance are provided as a convenience for informational purposes only and are subject to change without notice. The customer shall always ensure that the latest release of technical information is at his own disposal. Lati S.p.A. extends no warranties or guarantee, including a warranty of merchantability of whatever use is made of the product, and make no representations as to the accuracy, suitability, reliability, completeness and sufficiency of the information provided, and assume no responsibility regarding the consequences of its use or for any printing errors. It is the customer s responsibility to inspect and test our products in order to determine to his own satisfaction whether they are suitable for his intended uses and applications or used in conjunction with third-party materials This application-specific analysis shall at least include preliminary testing to determine the suitability for the customer s particular purpose from a technical as well as health, safety, and environmental standpoint. Such testing has not necessarily been done by us as the manner in which the customer use and the purpose to which utilise our products are beyond our control. Lati S.p.A. does not accept and hereby disclaims liability for, any damages whatsoever in connection with the use of or reliance on this information. No one is authorised to make any warranties, issue any immunities or assume any liabilities on behalf of Lati S.p.A. except in a writing signed by a specifically authorised Lati S.p.A. executive. Unless otherwise agreed in writing, the exclusive remedy for all claims is replacement of the product or refund of the purchase price at Lati s option, and in no event shall Lati S.p.A. be liable for special, consequential, incidental, punitive or exemplary damages. No information herein can be considered as a suggestion to use any product in conflict with intellectual property rights of third-parties. Lati S.p.A. disclaims any liability that may be claimed for infringement or alleged infringement of patents. Unless specifically stated in writing, the products mentioned herein are not suitable for applications in the pharmaceutical, medical or dental sector, in contact with foodstuff or for potable water transportation. For any other issues Lati S.p.A. Conditions of Sales apply. Copyright LATI S.p.A. 2010
18 HIGH PERFORMANCE THERMOPLASTICS PEEK PEEK PEEK PEEK PEEK PEEK PEEK PPS PPS PPS 10 G/60 10 K/20 10 K/30 10 K/ G/30 50 K/30 LARTON CE/60 LARTON G/40 LARTON GCE/600 abd jlm abc jlm abcd jkl abcd jkl ajk lm aj lm abcd jlm ab jl ab jl abj kl NB NB >300 >300 >300 >300 >300 >300 > >300 >300 >300 > >300 > >300 >300 >300 > >300 > V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-0 V-1 V-1 V-1 V-0 V AF PBB/PBDE and Sb 2 free HF Halogen free AG Chemically coupled K Carbon fibre B High fluidity KB, KB1 Red phosphorous C High viscosity KB3 Red phosphorous, suitable for warm & humid environments CE, CER, CET, KC, MX, TR, T, TES Mineral filler KB4 Red phosphorous. V0 at 0.75mm thickness. Improved CTI CP Special mineral filler L Oil stabilisation CT1 Improved CTI S Glass beads CT2 PBB/PBDE. Low Sb 2 content UV UV stabilisation CT3 Improved CTI. Halogen and red phosphorous free V Flame retardant CT4 Improved CTI. Low smoke density and low toxicity index VH Glycol and hydrolisis stabilisation E, PX Improved impact resistance V0, V1, V2 UL94-V0, V1, V2 FE Magnetizable filler W Metal stabilisation G Glass fibres V0E PBB/PBDE free H, H2, VH2 Heat stabilisation ---- UL approved
19 HIGH PERFORMANCE THERMOPLASTICS PPS PPS PPS PPS L-PPS L-PPS PSU PSU PSU PSU LARTON GCE/650 LARTON GK/400 LARTON K/20 LARTON K/30 LARTON L G/40 LARTON L K/20 LASULF LASULF G/15 LASULF G/20 LASULF G/30 abd jkl abcd jkl abc jkl abc jkl ab jl abc jkl abh kl abh kl ab hl ab hl NB NB NB NB NB NB NB NB NB NB NB NB E V-0 V-1 V-0 V-0 V-0 V-0 HB V-1 V-1 V-0 V * Values obtained according to ISO norm at the specified pressure. Actual shrinkage values may differ because of the design. Values shown are based on testing of injection moulded laboratory test specimens, conditioned according to the practice and represent data that fall within the standard range of properties for non-coloured material, if not otherwise specified. As they may be subject to variations, these values do not represent a sufficient basis for any part design and are not intended for use in establishing values for specification purposes. Properties of moulded parts can be influenced by a wide range of factors including, but not limited to, colorants, part design, processing conditions, post-treatment conditions, environmental conditions and usage of regrind during the moulding process. If data are explicitely indicated as provisional, range of properties has to be considered wider. This information and technical assistance are provided as a convenience for informational purposes only and are subject to change without notice. The customer shall always ensure that the latest release of technical information is at his own disposal. Lati S.p.A. extends no warranties or guarantee, including a warranty of merchantability of whatever use is made of the product, and make no representations as to the accuracy, suitability, reliability, completeness and sufficiency of the information provided, and assume no responsibility regarding the consequences of its use or for any printing errors. It is the customer s responsibility to inspect and test our products in order to determine to his own satisfaction whether they are suitable for his intended uses and applications or used in conjunction with third-party materials This application-specific analysis shall at least include preliminary testing to determine the suitability for the customer s particular purpose from a technical as well as health, safety, and environmental standpoint. Such testing has not necessarily been done by us as the manner in which the customer use and the purpose to which utilise our products are beyond our control. Lati S.p.A. does not accept and hereby disclaims liability for, any damages whatsoever in connection with the use of or reliance on this information. No one is authorised to make any warranties, issue any immunities or assume any liabilities on behalf of Lati S.p.A. except in a writing signed by a specifically authorised Lati S.p.A. executive. Unless otherwise agreed in writing, the exclusive remedy for all claims is replacement of the product or refund of the purchase price at Lati s option, and in no event shall Lati S.p.A. be liable for special, consequential, incidental, punitive or exemplary damages. No information herein can be considered as a suggestion to use any product in conflict with intellectual property rights of third-parties. Lati S.p.A. disclaims any liability that may be claimed for infringement or alleged infringement of patents. Unless specifically stated in writing, the products mentioned herein are not suitable for applications in the pharmaceutical, medical or dental sector, in contact with foodstuff or for potable water transportation. For any other issues Lati S.p.A. Conditions of Sales apply. Copyright LATI S.p.A. 2010
20 LATI: HIGH PERFORMANCE MATERIALS AND FULL TECHNICAL SUPPORT LATI has been developing high technology compounds during the last 25 years. Metal substitution, new polymers and formulations, advanced projects and engineering requirements: this huge amount of topics must be supported by an adequate know-how in order to help our Customers to implement our grades in new products. Today LATI can offer to its Customers a fully structured service including engineering, simulation, co-design and tailor made technical courses. Fluid-dynamical simulations: rheological description of LATI compounds are used to evaluate the moulding process into details, predicting filling and deformation issues. Skilled engineers will consequently suggest mould modifications, tips to stiffen the geometry of parts, correct moulding parameters and so on. The whole activity is performed by using the most updated and advanced computer technology available today. Fiber orientation prediction, cooling channel design, mould layout: every aspect of the moulding process is kept under strict control by LATI co-design engineers. Stress analysis: metal replacement can be suitable without problems by relying on finite element simulation, evaluating how plastic parts can withstand applied loads and deformations. Also in this case a full mechanical description is achieved by LATI laboratories and then forwarded to stress analysis stations for calculation. FEA can take into consideration any aspect related to project requirements: temperature, environmental conditions, contact with other bodies, creep and fatigue. The best numerical methods available on the marketused by highly skilled engineers graduated in polymer technology. Thermal analysis: it s the most recent development in FE simulation on polymers. Thermally conductive polymers can now be evaluated before proceeding with their implementation in new high end applications. By means of finite element thermal analysis, LATI can provide a strong support in calculating, e.g., working temperature of heat sinks and coolers for electronic industry in order to promote metal to plastic substitution. A real asset to polymer compound development. Technical training courses: polymer specialists and Customers must share their own knowledge to be very proactive in proposing to the market new compounds and new applications. LATI can provide in-house and on-site complete technical courses for engineers, technologists and designers in order to create a strong partnership between Supplier and Producer. Full courses on engineering, special compounds and designing with plastics will be performed by LATI specialists, combining passion for compounds with more than 60 years of experience.
21 LITERATURE Contact: LATI Industria Termoplastici S.p.A. Via F. Baracca, Vedano Olona (VA) - Italy Tel.: Fax: Special materials Product range LATI Special materials guide LATI Product range ETP, FR, HPP materials Latilub Engineering, flame-retardant and high performance engineering thermoplastics overview Engineering polymers featuring low coefficient of friction and high wear resistance INTRODUCTION TO SPECIALS [Vers. 003] INTRODUCTION TO ENGINEERING COMPOUNDS FLAME RETARDANTS HIGH PERFORMANCE LATILUB ENGINEERING POLYMERS FEATURING LOW COEFFICIENT OF FRICTION AND HIGH WEAR RESISTANCE LATI THERMOPLASTICS LASER MARKING Dimensional molding shrinkage Dimensional molding shrinkage of thermoplastic parts Definition of Laser Laser Marking Techniques Laser Beam Sources HIGH PERFORMANCE THERMOPLASTICS Compounding Solutions Laser marking LATI Thermoplastics laser marking Marking Quality and Technical Specifications Marking Effects Troubles and Poor Marking Performances Characteristics of the Beam-steered Laser Systems Thermoplastic Materials Markability Nd:YAG Laser - Marking Process Parameters Examples of Laser Marking Effects on Various Lati Engineering Thermoplastic Compounds LATI profile Chemical resistance data LATI Thermoplastic industries profile LATI chemical resistance ratings are referred to the base resins used in our compounds
PRODUCTS GUIDE ENGINEERING THERMOPLASTICS FLAME RETARDANT HIGH PERFORMANCE
PRODUCTS GUIDE ENGINEERING THERMOPLASTICS FLAME RETARDANT HIGH PERFORMANCE WHO IS LATI? LATI is a company founded in Italy in 1945. Since its foundation, it has been gaining a prestigious position in the
More informationCrastin PBT Thermoplastic polyester resins
Crastin PBT Thermoplastic polyester resins Product guide and properties Start with DuPont Engineering Polymers DuPont s registered trademark Crastin PBT Thermoplastic polyester resins Introduction CRASTIN
More informationPolyamide 6 for Injection Moulding
Polyamide 6 for Injection Moulding Promyde is a trademark of NUREL 1 NUREL Engineering Polymers Excellence in Polymerization Recent technical advancements in NUREL polymerization processes have enabled
More informationTECHNYL A 218 BLACK 21N
TECHNYL A 218 BLACK 21N Description TECHNYL A 218 Black 21 N is an unreinforced polyamide 66, standard viscosity, heat stabilized for injection moulding.it is available in black color. Key Properties Chemical
More informationPolyamide 6 & 66 for Injection Moulding
Polyamide 6 & 66 for Injection Moulding Promyde is a trademark of NUREL 1 NUREL Engineering Polymers Polymerization Integrated into In-House Compounding 50 years experience in polymerization processes
More informationQUALITY FITS. Product range injection molding grades with reference data
QUALITY FITS. Product range injection molding grades with reference data POCAN COLOR NOMENCLATURE Pocan is available in a large number of colors. We use a six-digit number to precisely characterize the
More informationAKROMID FR (PA 6.6, PA 6, PA 6.6/PA 6, PPA) AKROLOY FR (PA Blend)
FLAME-RETARDANT COMPOUNDS AKROMID FR (PA 6.6, PA 6, PA 6.6/PA 6, PPA) AKROLOY FR (PA Blend) AKRO-PLASTIC GmbH Member of the Feddersen Group Flame-retardant Products Increasingly Important for Extended
More informationAntifreeze Resistant Fatigue Resistant Gasoline Resistance Automotive Under the Hood ASTM D 4066 PA012G30 ASTM D 6779 PA012G30
Vydyne R530H Nylon resins are general purpose polyamide, heat stabilized, hydrolysis resistant, 30% glass fiber reinforced resins. Available in natural and black. It is specifically designed to maximize
More informationBADA CORPORATE PRESENTATION QUALITY FLEXIBILITY RELIABILITY YOUR INDIVIDUAL SPECIALIST FOR PLASTICS
BADA CORPORATE PRESENTATION YOUR INDIVIDUAL SPECIALIST FOR PLASTICS QUALITY FLEXIBILITY RELIABILITY BADA OUR EXPERTISE AT A GLANCE 3 BADA FACTS TWO STATE-OF-THE-ART PRODUCITON SITES Bühl (Baden)/Germany
More informationULTEM* 1010 Resin. SABIC Innovative Plastics - Polyether Imide. Actions. General Information. Product Description
ULTEM* 1010 Resin SABIC Innovative Plastics - Polyether Imide Actions General Information Product Description Transparent, enhanced flow Polyetherimide (Tg 217C). ECO Conforming, UL94 V0 and 5VA listing.
More informationPOlyNIl Product Brochure
POLYNIL Product Brochure APPLICATION PA6.6 Unreinforced for PRODUCT P50 FI P50 FIHS P50 FIBK P50 N P50 FL P50 FLBK P50 L Polynil P50 LBK PROPERTIES Internally Internally heat stabilized, Internally Nucleated,
More informationElastollan Product Range
Thermoplastic Polyurethane Elastomers (TPU) Elastollan Product Range Elastogran is Polyurethanes Contents Quality management to DIN EN ISO 9001 Page 2 Nomenclature for Elastollan Page 3 Packaging, Storage
More informationHigher Temperature PP-Based Composite Provides Nylon/PA- Level Performance at Lower Weight and Economic Feasibility
Higher Temperature PP-Based Composite Provides Nylon/PA- Level Performance at Lower Weight and Economic Feasibility Society of Plastic Engineers Automotive Composites Conference & Exhibition September
More informationThermx PCT. High-performance Polyester. Product and Properties Guide
Thermx PCT High-performance Polyester Product and Properties Guide Thermx Chemical resistance Processability Dimensional stability Heat resistance Fast molding cycles Thermx PCT polyester is a hightemperature
More informationCABELEC Conductive Compounds Product Selection Guide
Conductive Compounds CABELEC Conductive Compounds Product Selection Guide CABELEC Conductive Compounds Product SELECTION Guide Cabot s Performance Materials: Over 130 Years of Getting You Where You Want
More informationCONDUCTIVE COMPOUNDS. CABELEC Conductive Compounds Product Selection Guide
CONDUCTIVE COMPOUNDS CABELEC Conductive Compounds Product Selection Guide Cabot s Performance Materials: Over 130 Years of Getting You Where You Want to Go Cabot Corporation is a global performance materials
More information3M TM Dyneon TM Fluoroplastics. Product Comparison Guide.
3M TM Dyneon TM Fluoroplastics Product Comparison Guide. Characteristics 3M Dyneon Fluoroplastics. Nominal values, not for specification purposes 1) Melt Index is measured at the following conditions 265
More informationTexin 245 Covestro PUR Thermoplastic Polyurethane Elastomer (Polyester) Action Saturday, October 22, 2016 Units English Legend (Open) General Information Product Description Texin 245 resin is an aromatic
More informationContents. Product Portfolio 03. Product 04. Product Selection Guide 12. Integrated Solution 21. At a Glance 22. Global Network 23
Enjoy Our Excellence & Expertise ABS, ABS Alloy, ASA Contents Product Portfolio 03 Exclusive Product 04 Product Selection Guide 12 Integrated Solution 21 At a Glance 22 Global Network 23 Expertise Excellent
More informationWolf Kunststoff ZEDEX ZX-530 A5D Polymer Alloy
Wolf Kunststoff ZEDEX ZX-530 A5D Polymer Alloy Category : Polymer, Thermoplastic Material Notes: Main Characteristics: Low Creep; Low moisture absorption; Flame retardant; Low impurity ions; Good machinability;
More informationPublic Transportation Materials for a Moving Market
Public Transportation Materials for a Moving Market AKRO-PLASTIC GmbH Member of the Feddersen Group Weight-Reduced Products Gaining Importance for Applications in the Transportation Sector EU guidelines
More informationThe above data are preliminary and are subject to change as additional data are developed on subsequent lots.
Zenite LCP Product Information liquid crystal polymer resin 30% Glass Reinforced Liquid Crystal Polymer Resin PRELIMINARY DATA Zenite 7130 is a 30% glass reinforced LCP resin having excellent toughness
More informationMITRAS MATERIALS GMBH
MITRAS MATERIALS GMBH Friedrich-Ochs-Str. 2 92637 Weiden/Opf. Tel.: 0961 / 89-810 / 89-812 Fax: 0961 / 89-672 Directory of services L a b o r a t o r y MITRAS MATERIALS GMBH Edition 02/18 Rev. 08 page
More informationElectronic Materials Brochure
Electronic Materials Brochure TABLE OF CONTENTS 3 Introduction to Materials 4 ISODAMP C-8000 Materials 6 ISOLOSS SL Molding Materials - Thermosets 8 CONFOR EG Foams CONFOR SC Foams ISODAMP C-8000 MATERIALS
More informationDELO -PUR 9692 Multi-purpose 2c polyurethane, cures at room temperature, high-viscous, filled
DELO -PUR 9692 Multi-purpose 2c polyurethane, cures at room temperature, high-viscous, filled Base - polyurethane - two-component Use - for the bonding of metal, plastic and sometimes even elastomers -
More informationInspiring design innovation
IROGRAN Thermoplastic Polyurethanes Inspiring design innovation Product Overview IROGRAN TPU: Inspiring design innovation The manufacture of modern products, engineering components and technical parts
More informationCONDUCTIVE COMPOUND AND CONCENTRATES CABELEC CONDUCTIVE COMPOUNDS AND CONCENTRATES PRODUCT SELECTION GUIDE
CONDUCTIVE COMPOUND AND CONCENTRATES CABELEC CONDUCTIVE COMPOUNDS AND CONCENTRATES PRODUCT SELECTION GUIDE Performance and leadership in black plastics Cabot Corporation is a global performance materials
More informationSUPREME. Catalogue 2016/18 NEW. Fasteners and Components EXPANDED MATERIAL RANGE BLACK MOULDED SHOULDER WASHERS
NEW BLACK MOULDED SHOULDER WASHERS SUPREME Fasteners and Components Australia s Leading Supplier of High Quality Plastic Fasteners and Components Catalogue 2016/18 EXPANDED MATERIAL RANGE Natural Nylon
More informationQCB Thermoplastic Bearing Units
QCB Thermoplastic Bearing Units CAT TP 2017 E Ver1 NBC Group Ltd In the interest of continuing improvement, NBC Group Ltd reserves the right to modify any product or specification without prior notice.
More informationg/cm C Mpa % 2 kj/m Mpa Mpa -1-4 K x 10 C
PEPiping systems 7 plastics at sangir > technical details & applications > pe Technical details & applications Polyethylene Chemical composition of PE: Ethylene Polyethylene Polymer n Polyethylene is a
More informationGIACOGREEN Pipes and Fittings in Polypropylene Random
GIACOGREEN Pipes and Fittings in Polypropylene Random GIACOMINI s.p.a. 28017 S.Maurizio d Opaglio (Novara) Tel. 0322-923111 Fax 0322-96256 Telex 200035 www.giacomini.com dal 1951 January 2000 GIACOMINI,
More informationChallenges For Future Powerplant Coolant Systems
Challenges For Future Powerplant Coolant Systems Steven Mok, Karla Butler, Terrence Cressy, Paul Kane, Brian Fish (Presented at SPE Auto EPCON, April 28, 2009. Sterling Heights, MI) 2 Discussion Agenda
More informationREMA TECHNICAL INFORMATION DIN 80, 160, 320. Page 1 of 13
DIN 80, 160, 320 C O N N E C T O R D A T A S H E E T Page 1 of 13 DIN 80, 160 and 320 Connector datasheet REMA is the leading supplier of DIN-style (DIN standard 43589) quick-disconnect power connectors.
More informationSurface Protective Systems
Surface Protective Systems Technical information Oxydur VEL-SR Mechanical applied electrically conductive laminate system Base Vinyl ester resin Material Group Membranes Tank- / vessel linings - laminates
More informationADVANCED MEDICAL POLYMERS FOR THE LIFE OF YOUR PROGRAM. Medical Product Portfolio
ADVANCED MEDICAL POLYMERS FOR THE LIFE OF YOUR PROGRAM Medical Product Portfolio 1 OUR MEDICAL TECHNOLOGY POLYMERS MT PORTFOLIO OFFERS DESIGN FREEDOM AND ADVANCED PERFORMANCE Offering advanced polymer
More informationCHEZACARB. Conductive Carbon Black for Polymer Compounds SIMPLY IMPROVING EVERYDAY LIFE
CHEZACARB Carbon Black for Polymer Compounds SIMPLY IMPROVING EVERYDAY LIFE CHEZACARB AC COMPOUNDS CHEZACARB Volume resistivity as a function of CB content (extruded sheets) 1E+09 Carbon Black for Polymer
More informationAN RPM to TACH Counts Conversion. 1 Preface. 2 Audience. 3 Overview. 4 References
AN 17.4 RPM to TACH Counts Conversion 1 Preface 2 Audience 3 Overview 4 References This application note provides look up tables for the calculation of RPM to TACH Counts for use with the EMC2103, EMC2104,
More informationDELO-DUOPOX AD895 Multi-purpose 2c epoxy resin, cures at room temperature, medium-viscous, filled
DELO-DUOPOX AD895 Multi-purpose 2c epoxy resin, cures at room temperature, medium-viscous, filled Base - epoxy resin - two-component Use - high-strength construction adhesive - multi-purpose - the cured
More informationHigh Performance ABS Products for Automotive Applications
High Performance ABS Products for Automotive Applications ELIX Polymers is a leading manufacturer of ABS (Acrylonitrile-Butadiene-Styrene) resins and derivatives in Europe. Operating from its head office
More informationDelivery program Semi-finished plastics
Delivery program Semi-finished plastics Centroplast Engineering Plastics GmbH Engineering plastics belong to most important industrial materials. They convince above all by their level of performance and
More informationPOLYCAST CELL CAST ACRYLIC Solutions for Aerospace
POLYCAST CELL CAST ACRYLIC Solutions for Aerospace Delivering aircraft transparencies for the demanding aerospace industry. cast cell cast acrylic has been manufactured and trusted by the aerospace industry
More informationMATERIAL DATA SHEET* ALPANA d.o.o.
MATERIAL DATA SHEET* ALPANA d.o.o. Contents H-Pur Material Data Sheet... 2 LT-Pur Material Data Sheet... 3 S-Pur Material Data Sheet... 4 XH-Pur Material Data Sheet... 5 XSH-Pur Material Data Sheet...
More informationAKROMID A (PA 6.6) AKROMID B (PA 6) AKROLOY PA CompaDur PBT
P R O D U C T I N F O R M A T I O N B A S I C PR O G R A M AKROMID A (PA 6.6) AKROMID B (PA 6) AKROLOY PA PBT AKRO Engineering Plastics (Suzhou) Co., Ltd. Member of the Feddersen Group Dear AKRO-PLASTIC
More informationDRISCOPIPE 8100 HDPE PIPE and FITTINGS DATA SHEET
PerfmancePipe.com DRISCOPIPE 8100 HDPE PIPE and FITTINGS DATA SHEET Driscopipe 8100 Pipe and Fittings meet exceed: Driscopipe 8100 Pipe and Fittings f: ASTM D2513, D2683, D3261 ASTM D3350, cell classification
More informationDimensions / Order Codes
U-Bolt Clamps Dimensions / Flat Steel U-Bolt with Plastic Pipe Saddle (Short) and U-Profile Type FB+RUK (To be used as Fixed Point Clamps only) B1 ø D1 H4 H2 H3 H1 L2 L1 B2 Flat Steel U-Bolt (type FB)
More informationVERONEX Cases MATERIAL PERFORMANCE CHARACTERISTICS. MECHANICAL PROPERTIES Units Test method Result. THERMAL PROPERTIES Units Test method Result
VERONEX Cases VERONEX is a breakthrough in plastic enclosure design, combining the versatility and functionality demanded by engineers, with the modern styling appreciated by their customers. The VERONEX
More informationFK Series Automated Butterfly Valves Product Data Sheet
Product Data Sheet introduction < STANDARDS > ASTM D1784 ASTM D3222 ASTM D4101 IPEX FK Series Automated Butterfly Valves offer superior strength and chemical resistance in highly corrosive environments
More informationYELLOWSTRIPE 8300 BIMODAL HDPE PIPE DATA SHEET
PerformancePipe.com YELLOWSTRIPE 8300 BIMODAL HDPE PIPE DATA SHEET Yellowstripe 8300 Pipe meets or exceeds: ASTM D2513 CAN/CSA-B137.4 UPC ASTM D3350, cell classification PE445574C and PE445576C PPI TR-4
More informationNeopolen P 9230 ESD. Bulk density 1) Average Average Color 2) particle size particle weight [ kg/m 3 ] [ mm ] [ mg ]
= registered trademark of BASF SE Neopolen P 9230 ESD Product Description Neopolen P 9230 ESD is expanded Polypropylene supplied in the form of beads. The cells are largely closed. Table 1: Bulk density
More information1W, 10V - 200V Surface Mount Silicon Zener Diode
1W, 10V - 200V Surface Mount Silicon Zener Diode FEATURES Photo Glass passivated junction Ideal for automated placement Low inductance Typical IR less than 1μA above 11V Compliant to RoHS Directive 2011/65/EU
More informationDELO-DUOPOX AB8390 Multi-purpose 2c epoxy resin, cures at room temperature, high-viscous, filled
DELO-DUOPOX AB839 Multi-purpose 2c epoxy resin, cures at room temperature, high-viscous, filled Base - epoxy resin - two-component, thixotropic Use - high-strength construction adhesive - multi-purpose
More informationProduct Description PLEXIGLAS GS PLEXIGLAS XT
Product Description PLEXIGLAS GS PLEXIGLAS XT PLEXIGLAS trademark for the world s first acrylic was invented by us and first produced by the casting process in 1933. Today we manufacture PLEXIGLAS GS (=
More informationSR InfuGreen 810 Green Epoxy systems for Injection and Infusion
Page 1 / 9 SR InfuGreen 810 Green Epoxy systems for Injection and Infusion The InfuGreen 810 is a two-component epoxy system. It has been specially formulated for resin transfer processes, such as injection
More informationLAPOL HDT TECHNICAL BULLETIN
Raising the Heat Deflection Temperature of PLA LAPOL HDT TECHNICAL BULLETIN OCTOBER 2014 1 Polylactic Acid (PLA) The Front Runner in Bioplastics 100% degradable thermoplastic resin Made from renewable
More informationPVC SCHEDULE 40 FITTINGS
PVC SCHEDULE 40 FITTINGS Performance Engineered & Tested 40-2-0604 SPEARS Schedule 40 PVC fitting designs combine years of proven experience with computer generated stress analysis to yield the optimum
More informationStandard Classification System for Polyamide Molding and Extrusion Materials (PA) 1
Designation: D 6779 05 Stard Classification System for Polyamide Molding Extrusion Materials (PA) 1 This stard is issued under the fixed designation D 6779; the number immediately following the designation
More informationDELO-DUOPOX AD897 Multi-purpose 2c epoxy resin, cures at room temperature, high-viscous, filled
DELO-DUOPOX AD897 Multi-purpose 2c epoxy resin, cures at room temperature, high-viscous, filled Base - epoxy resin - two-component Use - for the trowelling of welded seams - pasty and run-resistant but
More informationBonstrand PSX L3, PSX L3C, PSX JF and PSX JFC Polysiloxane-phenolic Fire-resistant Fiberglass Pipe and Fittings
Bonstrand PSX L3, PSX L3C, PSX JF and PSX JFC Polysiloxane-phenolic Fire-resistant Fiberglass Pipe and Fittings For offshore platforms, marine and onshore service Description Bondstrand PSX JF and PSX
More informationZenite LCP Celanese LCP-009 AM 10/13
Zenite LCP 2013 Celanese LCP-009 AM 10/13 Zenite LCP Overview LCPs and Zenite LCP Zenite LCP Specific Properties Products and Roadmap UL Considerations Comparative Data 2013 Celanese LCP-009 AM 10/13 Zenite
More informationSolvay/ Torlon Thrust Bearing Discussion Torlon Versus Vespel Brian Stern
Solvay/ Torlon Thrust Bearing Discussion Torlon Versus Vespel 8-7-2018 Brian Stern Agenda Torlon Commercial Applications Thrust Bearing Requirements Torlon Property Discussion Torlon Friction and Wear
More informationDELO -PUR 9691 Multi-purpose 2c polyurethane, cures at room temperature, medium-viscous, filled
DELO -PUR 9691 Multi-purpose 2c polyurethane, cures at room temperature, medium-viscous, filled Base - polyurethane - two-component Use - for the bonding of metal, plastic and sometimes even elastomers
More informationATEVA MEDICAL EVA POLYMERS UNIQUE SOLUTIONS FOR YOU
ATEVA MEDICAL EVA POLYMERS UNIQUE SOLUTIONS FOR YOU WHAT IS ATEVA MEDICAL? Ateva Medical EVA-based resins deliver the reliable performance required for medical applications. Celanese can help companies
More informationMACP TB. 23 db Coupler MHz Rev. V1. Features. Functional Schematic. Description. Pin Configuration 4. Ordering Information 1,2
23 Coupler Features 23 Coupling Ratio Surface Mount Package Available on Tape and Reel Excellent Temperature Stability RoHS Compliant and Pb Free 260 C Reflow Compatible Description The MACP-0145 is a
More informationAhmedabad Textile Industry s Research Association (ATIRA), P.O. Ambawadi Vistar, Ahmedabad, Gujarat
Last Amended on - Page 1 of 13 I. TEXTILE MATERIALS 1. Fibre Micronaire Length Length uniformity Strength Elongation% Short fibre % Colour Whiteness (Rd) Colour Yellowness (+b) Neps/g Neps size SCN/g SCN
More informationHigh Current Thermal Fuse
High Current Thermal Fuse FEATURES Functioning temperature: F = (235 ± 15) C Holding temperature: H = 160 C Current: 50 A Suitable for insert assembly systems Material categorization: For definitions of
More informationPE-HDXc pipes (physically cross-linked polyethylene pipes)
pipes (physically cross-linked polyethylene pipes) Applications: Domestic drinking water installations, radiator connections and surface regulation Special properties high chemical resistance (according
More informationEngineering polymers in the underhood
Engineering polymers in the underhood The underhood of a car is a particularly challenging area because of high-temperature stresses (often above 100 C) and for the presence of aggressive liquids as gasoline,
More informationWiring Duct T1 Series - Slotted
Duct T1 Series - Slotted UL file E123572 T1 Series Gray Open Slot Rigid PVC (including cover) Catalog Standard Carton Package Quantity Price Catalog Single Piece Pkg Package Quantity Price T1-0506G 20
More informationSurface Protective Systems
Surface Protective Systems Technical information Oxydur VEL-U Laminate system for concrete and steel substrates Base Vinyl ester resin Material Group Membranes Tank- / vessel linings - laminates Description
More informationNORDEL EPDM Product Selection Guide
NORDEL EPDM Product Selection Guide NORDEL EPDM products are members of Dow s family of ethylene propylene diene terpolymers and feature the widest range of ethylene content available in the industry.
More informationSECTION A8 LUBRICITY
FORMATE TECHNICAL MANUAL C A B O T CHEMICAL AND PHYSICAL PROPERTIES SECTION A8 LUBRICITY A8.1 Introduction...2 A8.2 Lubricity tests from HLT Lubricity Tester...2 A8.2.1 Instrument description...2 A8.2.2
More information400W, 5V - 188V Surface Mount Transient Voltage Suppressor
400W, 5V - 188V Surface Mount Transient Voltage Suppressor FEATURES Low profile package Ideal for automated placement Glass passivated junction Excellent clamping capability Fast response time: Typically
More informationWeldalloy Catalogue 1
Weldalloy Catalogue 1 ONTE Contents P Pig s Tail Protective Wrapping........ 3 Pig s Tail Data Sheet.............. 4 Fire Resistant Anti Static Pig s Tail..... 6 Electrical Guard................... 7 Tidy
More informationStandard Classification System for Carbon Blacks Used in Rubber Products 1
Designation: D 1765 04 Standard Classification System for Carbon Blacks Used in Rubber Products 1 This standard is issued under the fixed designation D 1765; the number immediately following the designation
More informationEpoxy Resin L Unit Value
Technical data Epoxy Resin L + Hardener S, L, CL, EPH 500, W 300, GL 1, GL 2, EPH 573 and EPH 161 Low viscosity, free of solvents and fillers Fast impregnation of glass, aramid, and carbon fibres High
More informationPMP40001 Test Results
Test Report June 2016 PMP40001 Test Results 1 General 1.1 Purpose This test report is to provide the detailed data for evaluating and verifying the PMP40001 which employs one Buck-Boost Controller ----
More informationFlo-Way. Measure Granular or Powdered Material. Stand Alone or Connect to Other Devices for Blending. Used by Successful Producers World-Wide
Flo-Way R Solids Impact Flow Meter Measure Granular or Powdered Material Stand Alone or Connect to Other Devices for Blending Used by Successful Producers World-Wide Visit our website: www.beltwayscales.com
More information3 TM Cold Applied Barrier Boot System
M Technical Information : Barrier Boot TM Cold Applied Barrier Boot System For rated voltages 6.5/11(12) kv and 8.7/15(17.5) kv 92-EE 717-1 Product Description The Cold Applied Barrier Boot System consist
More informationPart Number: CAT6+ UTP CMR PRE-TERM 6 CAT6+ UTP CMR Pre-Term 6
Part Number: CAT6+ UTP CMR PRE-TERM 6 CAT6+ UTP CMR Pre-Term 6 Product Description CAT6+ UTP CMR Pre-Term 6 Technical Specifications Product Overview Environmental Space: Suitable Applications: Riser IBDN
More informationisovac high-perm A
Data sheet isovac P 400-65 A page 1/6 01/2018 Electrical Steel Fully processed Data sheet isovac P 400-65 A page 1/6 01/2018 isovac high-perm 400-65 A The specialist with the highest permeability Manufactured
More informationComponents: Dimensions / Order Codes Clamp Body. * 1st part of STAUFF Group 4. * Exact outside diameters Ø D1 / Ø D2 (mm) Clamp Body.
Components: Dimensions / Order Codes Clamp Body Clamp Body Colour: Green Material code: PP 4 PP One clamp body is consisting of two clamp halves. 1st part of STAUFF 4 Exact outside diameters Ø D1 / Ø D2
More informationSurface Protective Systems
Surface Protective Systems Technical information Oxydur UP 410 Laminate TI 216 Laminate system for concrete and steel substrates Base Polyester resin, unsaturated Material Group Membranes Tank- / vessel
More informationNTC Thermistors, Molded Range
2381 641 6... N Thermistors, Molded Range FEATURES Excellent for surface temperature measurement Designed for harsh environments Based on the 2322 640 0... naked thermistor chips. Old part number was 2322
More informationNEW APPLICATION TECHNOLOGIES IN PHENOLIC MOLDABLE COMPOSITES
NEW APPLICATION TECHNOLOGIES IN PHENOLIC MOLDABLE COMPOSITES 1. Why PF-GF have an increasing share of new engine components Plastics are replacing metal parts for a wide range of uses in the automotive
More informationVALSIR SUPPLY SYSTEMS MIXAL
TECHNICAL DATA SHEET VALSIR SUPPLY SYSTEMS MIXAL The product Mixal is an extremely flexible multilayer pipe and is therefore ideal for the creation of floor, wall and ceiling radiant heating and cooling
More informationCROSS REFERENCE CATALOG
Heatshrink Products NORTH AMERICAN HEATSHRINK CROSS REFERENCE CATALOG & ORDERING PROCEDURE HELLERMANNTYTON SIGMAFORM RAYCHEM 3M HEBRAN MIL. SPEC. NAVSEA Moulded Shapes HellermannTyton C O N T E N T S
More informationDual Lock Reclosable Fasteners Roll Goods with Pressure Sensitive Adhesive
3 Dual Lock Reclosable Fasteners Roll Goods with Pressure Sensitive Adhesive Technical Data Sheet June 2012 General Description Applications 3M Dual Lock Reclosable Fasteners are positive-locking, blind
More informationTKD SERIES 3-WAY BALL VALVES - TRUE UNION
TKD SERIES 3-WAY BALL VALVES - TRUE UNION The TKD offers a host of advanced features that set it apart from other multi-port valves. The patented seat stop carrier allows for in-line micro-adjustment of
More informationFusion Equipment & Tools Electrofusion Processor Scraper Tools Rerounding Tools Socket Fusion Kit
Fusion Equipment & Tools Electrofusion Processor Scraper Tools Rerounding Tools Socket Fusion Kit 71 I Fuse 105 Electrofusion Processor The IntegriFuse I Fuse 105 Electrofusion Processor is the next generation
More informationFluid Sealing Association
Fluid Sealing Association STANDARD FSA-DSJ-401-09 SPECIFICATION FOR HIGH TEMPERATURE AND ACID RESISTANT TERPOLYMER FLUOROELASTOMER REVISED OCTOBER, 2009 994 Old Eagle School Road, Suite 1019 Wayne, Pennsylvania
More informationDurable Goods Labelling Compliance
productoverview Durable Goods Labelling Compliance Durable goods require labels that give crucial instructions, product details and safety information. The labels have to stay in place and remain legible
More informationDELO -ML DB133 anaerobic and UV-curing adhesive
DELO -ML DB133 anaerobic and UV-curing adhesive Base - Modified urethane acrylate - one-component, solvent-free - dual-curing adhesive Use - for impact-resistant metal bondings - for mixed bondings with
More informationARALDITE AV 8574 Resin Hardener HV 8574
Advanced Materials ARALDITE AV 8574 Resin Hardener HV 8574 HEAT- AND CHEMICAL-RESISTANT EPOXY ADHESIVE DESCRIPTION ARALDITE AV 8574 Resin/Hardener HV 8574 epoxy adhesive is a twocomponent system suitable
More informationAdvanced Materials. Raising insulation performance in car electronics
Raising insulation performance in car electronics Quarter 2, 2013 Table of contents Raising performance Ignition coils Reliability and protection for electronic devices Improved endurance for ignition
More information3M CP2 Press-Fit Headers and Sockets, 2 mm
1 of 7 3M CP2 Press-Fit Headers and Sockets, 2 mm A-Style CP2 Connectors CP2-SA110-G1-KR Right Angle Socket Connectors mated to CP2-HA110-GA1-KR Header Connectors 78-5102-0083-1 Revised Date: February
More informationPromix Solutions trust the leader. Static Mixers Solutions for Injection Molding
Promix Solutions trust the leader Static Mixers Solutions for Injection Molding Your partner in the plastics processing industry Founded in 2012 as a spin-off of Sulzer Chemtech Subsidiaries in Winterthur,
More informationPart Number: 10GX F/UTP CMR PATCH CORDS 10GX F/UTP CMR Patch Cords
Part Number: 10GX F/UTP CMR PATCH CORDS 10GX F/UTP CMR Patch Cords Product Description 10GX F/UTP CMR Patch Cords Technical Specifications Product Overview Environmental Space: Suitable Applications: Riser
More informationHiPer-tex fibre for light weight, cost effective blast and ballistic protection solutions
HiPer-tex fibre for light weight, cost effective blast and ballistic protection solutions ballistic protection ballistic protection blast protection taking glass fibre to a higher level HiPer-tex fibre:
More informationS R O T A L SU IN INSULATORS
INSULATORS INSULATORS LV INSULATORS & MV BUSHINGS BMC & SMC MOULDED PARTS CONTENTS 03 04 05 LV Insulators Material Data LV Insulators Type SK Color: Red LV Insulators Type SK 06 07 08 09 10 11 LV Insulators
More informationManufacturer of Pig s Tail Protective Wrap
Manufacturer of Pig s Tail Protective Wrap ABOUT US Company Weldalloy, group of companies with production facilities on three continents, is the world s leading manufacturer of spiral protective wrap.
More information