Higher Temperature PP-Based Composite Provides Nylon/PA- Level Performance at Lower Weight and Economic Feasibility
|
|
- Carol Stevenson
- 6 years ago
- Views:
Transcription
1 Higher Temperature PP-Based Composite Provides Nylon/PA- Level Performance at Lower Weight and Economic Feasibility Society of Plastic Engineers Automotive Composites Conference & Exhibition September 13, 2012
2 Agenda ALBIS Group Mega-Trends and Market Drivers Performance PA GF / PP GF / PP LFRT next PP- NewTechnology next PP - Development Process Performance of next PP GF 35 next PP GF 35 - Aging Tests Drop-in solution / Warpage Target Applications Current Status Test Summary 2
3 ALBIS Group Facts & Figures Holding Foundation Turnover 2010/2011 Customers Employees Subsidiaries Compounding Sites Compounding Capacity Compounding Lines Certification ISO-9001 / ISO-TS OTTO KRAHN GmbH & Co. KG /733 Mio. EUR approx t/p.a /
4 ALBIS Group Global Network 4
5 Mega-Trends and Market Drivers Motivation for Material Substitution Weight reduction Lower density Lightweighting Improved fuel efficiency Vehicle Fuel efficiency CO2 emission reduction and higher MPG Economic feasibility Avoidance of Penalties (excess CO2 emissions) Material cost reduction (PP is lower cost base resin vs PA) Processing cost reduction with PP vs. PA No pre-drying necessary Lower processing temperatures use less energy and faster cycling Material Availability Broad supplier base for PP feedstock Better global availability of PP vs. PA 5
6 Mega-Trends and Market Drivers Vehicle Emission Standards European Union-Emission Standards (EC)443/2009: Target of 130g CO2/km for 2012 phase-in basis between 2012 & % % % % Penalties effective 2015: +1g 5,-Euro/car +2g 10,- Euro/car +3g 45,- Euro/car +4g 155,- Euro/car +5g 240,- Euro/car effective 2019: +1g 95,- Euro/car Target of 95g CO2/km for 2020 (to be reviewed in 2013) Source: Broschure Worldwide Emission Standards and Related Regulations, Continental Automotive GmbH, New emission standards drive weight reduction. 6
7 Mega-Trends and Market Drivers Emission Standards Penalties Source: Report How clean are Europe s cars?, European Federation for Transport and Environment (T&E), If Daimler, Volvo, BMW are not fulfilling Emission Standards they could face severe penalties as of 2015, i.e. would result in ca. 1,000,000,000 Euro 7
8 Mega-Trends and Market Drivers Emissions Reduction Impacts Design What does all this mean for Car Manufacturers / Suppliers? Weight reduction Metal replacement Lower density polymers/ fillers (e.g. PA=>PP, hollow glass) Carbon fibre technology Foaming, gas-injection, etc. Electrification Supercredits (<50g cars, equal 3,5cars) Electrical performance, high voltage Downsizing, i.e. smaller, powerful engines Mechanics Heat / creep resistance Aggressive liquids, i.e. fuels, lubes, etc. Chemical resistance Biofuel resistance (E10, E85) Market Driven vs. Customising. New Product Designs 8
9 Mega-Trends and Market Drivers Growth of Plastics Usage [kg] Growth of plastics usage in cars 190 kg 235 kg 250 kg kg 134 kg kg 12 % 14 % 12 % 15 % 16 % 20 % Golf I Golf II Golf III Golf IV Golf V Golf VI Source: VDI - Plastics in Automotive Engineering, Mannheim, Weight and cost reduction drive increased use of plastics. 9
10 Mega-Trends and Market Drivers Inter-Polymer Competition Substitution chain in the plastics industry Current status next PP close the gap 10
11 Performance PA GF / PP GF / PP LFRT Current Status Properties PP-H GF30 PA6 GF30 PP LFRT 30 Density [g/cm³] 1,12 1,36 1,12 ISO 1183 tensile strength [MPa] 23 C * 110 DIN EN ISO 527 E-Modul [MPa] 23 C * 6300 DIN EN ISO 527 elongation at break [%] 23 C 2 5* 2,3 DIN EN ISO 527 E-Modul [MPa] 75 C * 4600 DIN EN ISO 527 E-Modul [MPa] 120 C * 3500 DIN EN ISO 527 HDT A [ C] 138 > DIN EN ISO 75 Flexural strength [MPa] * 147 DIN EN ISO 178 Charpy unnotched [kj/m²] 23 C 12 70* 52 Charpy notched [kj/m²] 23 C 5 11* 19 DIN EN ISO 179/1eU DIN EN ISO 179/1eA Flow spiral [mm] ALBIS Norm * conditioned 11
12 next PP - New Technology A technical alternative to PA6 and PP LFRT compound Based on low cost, approved Polypropylene matrix New innovative technology Closing the gap between commodities and engineering resins 12
13 next PP - Development Process 15 months development time Approx. 190 production runs on laboratory extruder in R+D Formulation development Processing development Determination of mechanical properties through internal and external laboratory 9 Production trials Scale up Processing development Optimazation dosing position and units Optimazation screw design Maximization throughput 13
14 Performance of next PP GF 35 E-Modulus vs. Temperature E-Modul [MPa] PA6 GF30 (cond.) next PP GF35 PP-H GF30 PP LFRT Temperatur [ C] Up to 110 C very similar to Nylon and PP LFRT 30 14
15 Performance of next PP GF 35 Benchmark I Properties PP-H GF30 PA6 GF30 PP LFRT 30 next PP GF 35 Density [g/cm³] 1,12 1,36 1,12 1,18 ISO 1183 tensile strength [MPa] 23 C * DIN EN ISO 527 E-Modul [MPa] 23 C * DIN EN ISO 527 elongation at break [%] 23 C 2 5* 2,3 3 DIN EN ISO 527 E-Modul [MPa] 75 C * DIN EN ISO 527 E-Modul [MPa] 120 C * DIN EN ISO 527 HDT A [ C] 138 > DIN EN ISO 75 Flexural strength [MPa] * DIN EN ISO 178 Charpy unnotched [kj/m²] 23 C Charpy notched [kj/m²] 23 C DIN EN ISO 179/1eU DIN EN ISO 179/1eA Flow spiral [mm] ALBIS Norm * conditioned 15
16 Performance of next PP GF 35 Benchmark Il Flow spiral E-Modul 23 C 200% 180% 160% 140% 120% E-Modul 75 C next PP 30 PP LFRT 30 PA 6 GF 30 con. 100% Charpy notched 80% 60% E-Modul 120 c 40% Charpy unnotched tensile strength 23 C Flexural strength HDT A next PP shows comparable properties with better flowability 16
17 next PP GF 35 - Aging Tests Thermal Storage Tests Hot air storage (Ofen storage) E-Modul DIN EN ISO 527 tensile strength DIN EN ISO 527 [MPa] [MPa] 0h / 23 C 1000h / 130 C 0h / 23 C 1000h / 150 C elongation at break [%] DIN EN ISO 527 Flexural modulus DIN EN ISO 178 Charpy unnotched DIN EN ISO 179/1eU Charpy notched DIN EN ISO 179/1eA [MPa] [kj/m²] [kj/m²] 3,0 3,0 2,7 2, No reduction of the properties after thermal storage 17
18 next PP GF 35 - Aging Tests Oil aging test Oil aging 90 C Tensile Strength Un. Charpy (23 C) 120% 100% 80% 60% 40% 20% 0% E-Modul 23 C next PP GF 35 PA GF 30 VWRequirement Flexural Modulus Flexural Strength 18
19 next PP GF 35 - Aging Tests Glycol aging test Glycol aging 90 C Un. Charpy (23 C) Tensile Strength 120% 100% 80% 60% 40% 20% 0% E-Modul PA GF 30 next PP GF 35 VW Requirement Flexural Modulus Flexural Strength 19
20 next PP GF 35 Drop-in solution / Warpage shrinkage PA 6 GF 30 next PP GF 35 longitudinal 0,16 0,4 transverse 0,82 0,6 averaged 0,49 0,5 Drop-in solution, due to comparable shrinkage Less warpage, due to smaller difference between longitudinal and transverse shrinkage 20
21 next PP GF35 Targets / Applications Main focus areas: 1. Automotive Under the hood 2. E&E engine cover, fan frame, fuse box, air intake manifold, etc. Power tools Appliances 3. General industries Furniture Other existing PA6 GF applications 21
22 next PP GF 35 Current Status Tests FMVSS 302 (flambility test) passed Shrinkage 60x60x2 mm 3 (parallel / transverse) 0,3-0,4 / 0,5-0,6 Glow wire test/ mm - 4 mm passed GWFI IEC Emissions not finished Media storage not finished Scratch resistance test not finished 22
23 next PP GF 35 Summary Weight reduction (ca. -18% vs. PA) Economic feasibility Excellent HDT performance (HDT A = 154 C); PP GF 140 C, PP LFRT 156 C, PA GF > 200 C High stiffness (> C) Good aging properties Drop-in solution / Warpage Processing advantages (Flow spiral approx. 94 cm) Outstanding surface properties 23
24 Thank you for your attention! Jim Keeler,
Crastin PBT Thermoplastic polyester resins
Crastin PBT Thermoplastic polyester resins Product guide and properties Start with DuPont Engineering Polymers DuPont s registered trademark Crastin PBT Thermoplastic polyester resins Introduction CRASTIN
More informationPolyamide 6 for Injection Moulding
Polyamide 6 for Injection Moulding Promyde is a trademark of NUREL 1 NUREL Engineering Polymers Excellence in Polymerization Recent technical advancements in NUREL polymerization processes have enabled
More informationPolyamide 6 & 66 for Injection Moulding
Polyamide 6 & 66 for Injection Moulding Promyde is a trademark of NUREL 1 NUREL Engineering Polymers Polymerization Integrated into In-House Compounding 50 years experience in polymerization processes
More informationTECHNYL A 218 BLACK 21N
TECHNYL A 218 BLACK 21N Description TECHNYL A 218 Black 21 N is an unreinforced polyamide 66, standard viscosity, heat stabilized for injection moulding.it is available in black color. Key Properties Chemical
More informationQUALITY FITS. Product range injection molding grades with reference data
QUALITY FITS. Product range injection molding grades with reference data POCAN COLOR NOMENCLATURE Pocan is available in a large number of colors. We use a six-digit number to precisely characterize the
More informationAKROMID FR (PA 6.6, PA 6, PA 6.6/PA 6, PPA) AKROLOY FR (PA Blend)
FLAME-RETARDANT COMPOUNDS AKROMID FR (PA 6.6, PA 6, PA 6.6/PA 6, PPA) AKROLOY FR (PA Blend) AKRO-PLASTIC GmbH Member of the Feddersen Group Flame-retardant Products Increasingly Important for Extended
More informationPOlyNIl Product Brochure
POLYNIL Product Brochure APPLICATION PA6.6 Unreinforced for PRODUCT P50 FI P50 FIHS P50 FIBK P50 N P50 FL P50 FLBK P50 L Polynil P50 LBK PROPERTIES Internally Internally heat stabilized, Internally Nucleated,
More informationHigh Performance ABS Products for Automotive Applications
High Performance ABS Products for Automotive Applications ELIX Polymers is a leading manufacturer of ABS (Acrylonitrile-Butadiene-Styrene) resins and derivatives in Europe. Operating from its head office
More informationAntifreeze Resistant Fatigue Resistant Gasoline Resistance Automotive Under the Hood ASTM D 4066 PA012G30 ASTM D 6779 PA012G30
Vydyne R530H Nylon resins are general purpose polyamide, heat stabilized, hydrolysis resistant, 30% glass fiber reinforced resins. Available in natural and black. It is specifically designed to maximize
More informationPublic Transportation Materials for a Moving Market
Public Transportation Materials for a Moving Market AKRO-PLASTIC GmbH Member of the Feddersen Group Weight-Reduced Products Gaining Importance for Applications in the Transportation Sector EU guidelines
More informationREMA TECHNICAL INFORMATION DIN 80, 160, 320. Page 1 of 13
DIN 80, 160, 320 C O N N E C T O R D A T A S H E E T Page 1 of 13 DIN 80, 160 and 320 Connector datasheet REMA is the leading supplier of DIN-style (DIN standard 43589) quick-disconnect power connectors.
More informationCABELEC Conductive Compounds Product Selection Guide
Conductive Compounds CABELEC Conductive Compounds Product Selection Guide CABELEC Conductive Compounds Product SELECTION Guide Cabot s Performance Materials: Over 130 Years of Getting You Where You Want
More informationCONDUCTIVE COMPOUND AND CONCENTRATES CABELEC CONDUCTIVE COMPOUNDS AND CONCENTRATES PRODUCT SELECTION GUIDE
CONDUCTIVE COMPOUND AND CONCENTRATES CABELEC CONDUCTIVE COMPOUNDS AND CONCENTRATES PRODUCT SELECTION GUIDE Performance and leadership in black plastics Cabot Corporation is a global performance materials
More informationCONDUCTIVE COMPOUNDS. CABELEC Conductive Compounds Product Selection Guide
CONDUCTIVE COMPOUNDS CABELEC Conductive Compounds Product Selection Guide Cabot s Performance Materials: Over 130 Years of Getting You Where You Want to Go Cabot Corporation is a global performance materials
More informationDr.-Ing. Hosen SULAIMAN, Klaus UNRUH 16 June Steel in Automotive Industry The View from the Supply Chain
Dr.-Ing. Hosen SULAIMAN, Klaus UNRUH 16 June 2015 Steel in Automotive Industry The View from the Supply Chain Agenda Introduction Current situation on steel usage and delivery Material approval and future
More informationNEW APPLICATION TECHNOLOGIES IN PHENOLIC MOLDABLE COMPOSITES
NEW APPLICATION TECHNOLOGIES IN PHENOLIC MOLDABLE COMPOSITES 1. Why PF-GF have an increasing share of new engine components Plastics are replacing metal parts for a wide range of uses in the automotive
More informationCHEZACARB. Conductive Carbon Black for Polymer Compounds SIMPLY IMPROVING EVERYDAY LIFE
CHEZACARB Carbon Black for Polymer Compounds SIMPLY IMPROVING EVERYDAY LIFE CHEZACARB AC COMPOUNDS CHEZACARB Volume resistivity as a function of CB content (extruded sheets) 1E+09 Carbon Black for Polymer
More informationEuropean Good Practices in. chains Lighter than light Potential of blends from natural fibres and recycled carbon fibres for lightweight applications
European Good Practices in Eco-creativity, creativity, natural fibres & short value chains Lighter than light Potential of blends from natural fibres and recycled carbon fibres for lightweight applications
More informationBASF s Performance Polymers Delivering sustainable value
BASF s Delivering sustainable value Wolfgang Hapke President Performance Polymers Division September 5, 2012 A strategic fit for BASF BASF Group sales 2011 Oil & Gas 16% Other 9% Chemicals 18% Agricultural
More informationThe above data are preliminary and are subject to change as additional data are developed on subsequent lots.
Zenite LCP Product Information liquid crystal polymer resin 30% Glass Reinforced Liquid Crystal Polymer Resin PRELIMINARY DATA Zenite 7130 is a 30% glass reinforced LCP resin having excellent toughness
More informationLAPOL HDT TECHNICAL BULLETIN
Raising the Heat Deflection Temperature of PLA LAPOL HDT TECHNICAL BULLETIN OCTOBER 2014 1 Polylactic Acid (PLA) The Front Runner in Bioplastics 100% degradable thermoplastic resin Made from renewable
More informationElastollan Product Range
Thermoplastic Polyurethane Elastomers (TPU) Elastollan Product Range Elastogran is Polyurethanes Contents Quality management to DIN EN ISO 9001 Page 2 Nomenclature for Elastollan Page 3 Packaging, Storage
More informationFull Composite Solutions for Mobile Hydraulic Applications
Full Composite Solutions for Mobile Hydraulic Applications WIEFP 2014, Sao Paulo 02. Sept. 2014 The reproduction, distribution and utilization of this document as well as the communication of its contents
More informationWolf Kunststoff ZEDEX ZX-530 A5D Polymer Alloy
Wolf Kunststoff ZEDEX ZX-530 A5D Polymer Alloy Category : Polymer, Thermoplastic Material Notes: Main Characteristics: Low Creep; Low moisture absorption; Flame retardant; Low impurity ions; Good machinability;
More informationThermx PCT. High-performance Polyester. Product and Properties Guide
Thermx PCT High-performance Polyester Product and Properties Guide Thermx Chemical resistance Processability Dimensional stability Heat resistance Fast molding cycles Thermx PCT polyester is a hightemperature
More informationAKROMID A (PA 6.6) AKROMID B (PA 6) AKROLOY PA CompaDur PBT
P R O D U C T I N F O R M A T I O N B A S I C PR O G R A M AKROMID A (PA 6.6) AKROMID B (PA 6) AKROLOY PA PBT AKRO Engineering Plastics (Suzhou) Co., Ltd. Member of the Feddersen Group Dear AKRO-PLASTIC
More informationChallenges For Future Powerplant Coolant Systems
Challenges For Future Powerplant Coolant Systems Steven Mok, Karla Butler, Terrence Cressy, Paul Kane, Brian Fish (Presented at SPE Auto EPCON, April 28, 2009. Sterling Heights, MI) 2 Discussion Agenda
More informationFuture Development Targets for manual Transmissions
Future Development Targets for manual Transmissions International VDI-Congress 2013 Friedrichshafen Dipl.-Ing. Wulf Leitermann, Platform Director Manual Transmissions & Components, GETRAG GmbH & Cie K
More informationBOGE Rubber & Plastics achieves record sales and extends its product portfolio with Fiberreinforced rubber-elastic coupling
Automotive supplier remains on an expansion course BOGE Rubber & Plastics achieves record sales and extends its product portfolio with Fiberreinforced rubber-elastic coupling Sales grow by 8.6 percent
More informationGlobal Automotive DowAksa current focus
Global Automotive DowAksa current focus World at a glance Light weighting is not a new idea Key Market Driver: Mass Reduction CALIFORNI Mass reduction is vital for car makers to avoid fuel efficiency or
More informationvoestalpine automotive Components Linz
voestalpine automotive Components Linz Tailored Solutions for the Automotive Industry www.voestalpine.com Agenda Company overview Plant expansion Examples of TWB Applications 2 7/3/2017 Maserati Alfa Romea
More informationROLLER LUBRICANT VISCOSITY RATING
CHAIN INFORMATION OUTER PLATE OUTER PLATE PIN 2 PIECES OF EACH MAKE AN OUTER LINK BUSH INNER PLATE INNER PLATE 2 PIECES OF EACH MAKE AN INNER LINK ROLLER AMERICAN BRITISH Lubrication (Dependent on power
More informationThe Future of Mobility. Dhiren Verma VP, Analytics June 22, 2016
The Future of Mobility Dhiren Verma VP, Analytics June 22, 2016 Our Vision To radically change the way organizations design products and make decisions We Work with Some of the Best Automotive Aerospace
More informationHANNOVER MESSE Materials Forum
HANNOVER MESSE Materials Forum Novel Fibre Reinforced Polymers for the Automobile Interior Lightweight Structural Components in a Multi-Material Design Hannover, 10 th April 2013 R. Matheis, T. Schulte,
More informationVISCOBASE Synthetic Base Fluids. Economical solutions for high-performance automotive and industrial gear oils
VISCOBASE Synthetic Base Fluids Economical solutions for high-performance automotive and industrial gear oils High-performance base fluids and lubricant additives The oil additives specialists at Evonik
More informationArcelorMittal. The leading supplier to the automotive industry in Europe
ArcelorMittal The leading supplier to the automotive industry in Europe September 2016 European leadership towards automotive customers 1 Market needs To develop global operations to respond to the needs
More informationKLINGER soft-chem. Benefits: Key features: Certificates and approvals: Properties: Industries:
KLINGER soft-chem KLINGER soft-chem brings the sealing technology on a new level and it is the best choice for operating conditions up to 260 C. Multi-directional expanded PTFE Excellent corrosion resistance
More informationAdvanced Materials. Raising insulation performance in car electronics
Raising insulation performance in car electronics Quarter 2, 2013 Table of contents Raising performance Ignition coils Reliability and protection for electronic devices Improved endurance for ignition
More informationEngine encapsulation. A synergic approach to exterior noise and CO 2 emissions reduction. Brussels, 18th December 2012 Maurizio Mantovani - Autoneum
Engine encapsulation A synergic approach to exterior noise and CO 2 emissions reduction Brussels, 18th December 2012 Maurizio Mantovani - Autoneum Agenda 1. Who is Autoneum 2. Benefits of encapsulation
More informationPRODUCTION OF POLYETHYLENE AND POLYPROPYLENE PIPES POLYPROPYLENE SEWAGE PIPES KONTI KAN PP-HM.
PRODUCTION OF POLYETHYLENE AND POLYPROPYLENE PIPES POLYPROPYLENE SEWAGE PIPES KONTI KAN PP-HM www.konti-hidroplast.com.mk CONTENTS INTRODUCTION...2 PRODUCT DESCRIPTION...5 PIPE PROFILE AND...7 SOLID CONNECT...9
More informationBenteler Distribution. Steel tube solutions for hydraulic and pneumatic applications
Benteler Distribution Steel tube solutions for hydraulic and pneumatic applications Benteler Distribution Customized steel tube solutions for challenging requirements Benteler Distribution is an internationally
More informationLubrication Needs for Next Generation Gasoline Passenger Car Engine Technology
Lubrication Needs for Next Generation Gasoline Passenger Car Engine Technology V Simpósio de Lubrificantes, Aditivos e Fluidos São Paulo, Brasil, October 24, 2012 Ravi Tallamraju Passenger Car Motor Oil
More informationSUPREME. Catalogue 2016/18 NEW. Fasteners and Components EXPANDED MATERIAL RANGE BLACK MOULDED SHOULDER WASHERS
NEW BLACK MOULDED SHOULDER WASHERS SUPREME Fasteners and Components Australia s Leading Supplier of High Quality Plastic Fasteners and Components Catalogue 2016/18 EXPANDED MATERIAL RANGE Natural Nylon
More informationxperion Energy & Environment GmbH Otto-Hahn-Strass Kassel Germany
xperion Energy & Environment GmbH Otto-Hahn-Strass 5 34123 Kassel Germany http:// About the Company xperion Energy & Environment GmbH is a global oriented company within the Avanco Group. With high-end
More informationVISCOBASE Synthetic Base Fluids ECONOMICAL SOLUTIONS FOR HIGH-PERFORMANCE AUTOMOTIVE AND INDUSTRIAL GEAR OILS
VISCOBASE Synthetic Base Fluids ECONOMICAL SOLUTIONS FOR HIGH-PERFORMANCE AUTOMOTIVE AND INDUSTRIAL GEAR OILS HIGH-PERFORMANCE BASE FLUIDS AND LUBRICANT ADDITIVES The Oil Additives specialists at Evonik
More informationAKROMID A (PA 6.6) AKROMID B (PA 6) AKROMID C (PA 6.6/PA 6 Blend)
P R O D U C T I N F O R M A T I O N B A S I C P R O G R A M AKROMID A (PA 6.6) AKROMID B (PA 6) AKROMID C (PA 6.6/PA 6 Blend) AKRO-PLASTIC GmbH Member of the Feddersen Group Dear AKRO-PLASTIC customers,
More informationULTEM* 1010 Resin. SABIC Innovative Plastics - Polyether Imide. Actions. General Information. Product Description
ULTEM* 1010 Resin SABIC Innovative Plastics - Polyether Imide Actions General Information Product Description Transparent, enhanced flow Polyetherimide (Tg 217C). ECO Conforming, UL94 V0 and 5VA listing.
More informationK-Resin SB Copolymer/Crystal Polystyrene Sheet Property Modification with High Impact Polystyrene
Styrene-Butadiene Copolymers Plastics Technical Center Report #9 K-Resin SB Copolymer/Crystal Polystyrene Sheet Property Modification with High Impact Polystyrene INTRODUCTION. Many sheet extruders are
More informationEpoxy Resin L Unit Value
Technical data Epoxy Resin L + Hardener S, L, CL, EPH 500, W 300, GL 1, GL 2, EPH 573 and EPH 161 Low viscosity, free of solvents and fillers Fast impregnation of glass, aramid, and carbon fibres High
More informationOutline of Genestar Business. September 11, 2018
Outline of Business September 11, 2018 What is? Well-balanced of (80 C ; after water absorption), also known as PA9T, is a heat resistant polyamide resin which Kuraray has developed using its unique monomer
More informationDRIVING WITH FEWER EMISSIONS: how can carmakers meet the 2021 targets for CO 2. emissions?
DRIVING WITH FEWER EMISSIONS: how can carmakers meet the 2021 targets for CO 2 emissions? DRIVING CHANGE: HOW CAN CARMAKERS MEET THE 2021 TARGETS FOR CO 2 2 Our new forecast shows many carmakers are struggling
More informationINTRODUCTION TO ENGINEERING COMPOUNDS FLAME RETARDANTS HIGH PERFORMANCE
INTRODUCTION TO ENGINEERING COMPOUNDS FLAME RETARDANTS HIGH PERFORMANCE PRODUCTS ETP, FR, HPP LATI NOMENCLATURE NATURAL & COLOURED MINERAL FILLED GLASS BEADS GLASS FIBRES CARBON FIBRES ELASTOMER MODIFIED
More informationWelcome to the world of HCS Group. Company Presentation, May 2018
Welcome to the world of HCS Group. Company Presentation, May 2018 istockphoto Our Vision HCS Group is a leading global provider of solutions for high-value specialty hydrocarbons HCS Group HCS Group Leading
More informationDELO-DUOPOX AD895 Multi-purpose 2c epoxy resin, cures at room temperature, medium-viscous, filled
DELO-DUOPOX AD895 Multi-purpose 2c epoxy resin, cures at room temperature, medium-viscous, filled Base - epoxy resin - two-component Use - high-strength construction adhesive - multi-purpose - the cured
More informationEngineering polymers in the underhood
Engineering polymers in the underhood The underhood of a car is a particularly challenging area because of high-temperature stresses (often above 100 C) and for the presence of aggressive liquids as gasoline,
More informationHow to industrialize CFRPs? Challenges and opportunities
How to industrialize CFRPs? Challenges and opportunities 11th International Carbon Festival October 05-07, 2016 David Weinberg, Voith Composites GmbH & Co. KG 1 Agenda Voith Composites CFRPs: Challenges
More informationMicrocellular polyurethane as steering coupling element
Microcellular polyurethane as steering coupling element Material specific properties of solutions based on Cellasto -Elastolit-X composite structures Contents Cellasto material specific properties: Classification,
More informationRoadmaps, Projects And Future Plans of the European Green Cars Initiative PPP. Dr. Beate Müller VDI VDE Innovation + Technik GmbH Berlin, Germany
Roadmaps, Projects And Future Plans of the European Green Cars Initiative PPP Dr. Beate Müller VDI VDE Innovation + Technik GmbH Berlin, Germany EU Policy for Clean Transport Europe 2020 Strategy 20% cut
More informationDETAIL SPECIFICATION SHEET INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, CROSSLINKED CHLORINATED POLYOLEFIN, FLEXIBLE
INCH-POUND MIL-DTL-23053/1C 17 June 1996 SUPERSEDING MIL-I-23053/1B 01 May 1986 DETAIL SPECIFICATION SHEET INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, CROSSLINKED CHLORINATED POLYOLEFIN, FLEXIBLE
More informationFossil-fuel resources becoming more costly: economically, environmentally & geopolitically.
Fossil-fuel resources becoming more costly: economically, environmentally & geopolitically. A need exists for sustainable, low-cost, bio-based feedstock in the renewable plastics industry. Diversion of
More informationDELO-DUOPOX AD897 Multi-purpose 2c epoxy resin, cures at room temperature, high-viscous, filled
DELO-DUOPOX AD897 Multi-purpose 2c epoxy resin, cures at room temperature, high-viscous, filled Base - epoxy resin - two-component Use - for the trowelling of welded seams - pasty and run-resistant but
More informationATEVA MEDICAL EVA POLYMERS UNIQUE SOLUTIONS FOR YOU
ATEVA MEDICAL EVA POLYMERS UNIQUE SOLUTIONS FOR YOU WHAT IS ATEVA MEDICAL? Ateva Medical EVA-based resins deliver the reliable performance required for medical applications. Celanese can help companies
More informationCompostable Solutions for Packaging. FlexPackCon 2016 Randy Jester
Compostable Solutions for Packaging FlexPackCon 2016 Randy Jester 10/14/2016 1 Overview Film structural polymers ecovio aliphatic-aromatic polyester / PLA blend ecoflex aliphatic-aromatic polyester Packaging
More informationDATA SHEET OF COMPASHIELD EE GASKET
DATA SHEET OF COMPASHIELD EE GASKET Introduction Compashield EE gaskets developed by Nolato is extruded in parallel with dual conductive/non-conductive gaskets, provide both optimum EMI and environmental
More informationAdvanced compounds for superior parts
Advanced compounds for superior parts Michael Sommer Glenn Mazza Menzolit Compounds International BYK July 2007 Content 1 2 3 4 5 Rising demands Finding answers to the new challenges Automotive applications
More informationAnnex to the Accreditation Certificate D-PL according to DIN EN ISO/IEC 17025:2005
Deutsche Akkreditierungsstelle GmbH Annex to the Accreditation Certificate D-PL-17435-01-00 according to DIN EN ISO/IEC 17025:2005 Period of validity: 30.09.2016 to 08.12.2018 Holder of certificate: k3works
More informationInspiring design innovation
IROGRAN Thermoplastic Polyurethanes Inspiring design innovation Product Overview IROGRAN TPU: Inspiring design innovation The manufacture of modern products, engineering components and technical parts
More informationLitarion GmbH Electrovaya Inc.
Litarion GmbH Electrovaya Inc. Lithium Ion Technology beyond the Standard Company Presentation 08/2017 Company Group System integration: From cassettes and modules up to MWh scale energy storage 160,000
More informationTRUCKTEC T R U C K T E C
T R U C K T E C H i s t o r y a n d P r o g r e s s TRUCKTEC a u t o m o t i v e H i s t o r y Our success proves we are doing it right. What started just yesterday is continuously evolving. We are developing
More informationDeep-dive E-Mobility
Dr. Jochen Schröder President Business Division E-Mobility CES - 17th Annual J.P. Morgan Auto Tech Conference Las Vegas Automotive OEM at a glance Automotive OEM At a Glance Sales and EBIT margin 3) Sales
More informationAutomotive R&D: Energy, Transport & ICT
Automotive R&D: Energy, Transport & ICT Dr. Simon Godwin Director, EUCAR JRC Roundtable, Brussels, 15 th February 2012 European Automobile Industry OEMs turnover of 536bn (total automotive industry 847bn).
More informationHonda Clarity Fuel Cell HyLAW National Workshop, Budapest, 27. September 2018
Honda Clarity Fuel Cell HyLAW National Workshop, Budapest, 27. September 2018 Thomas Brachmann Technical Leader New Energy and Fuel Cell Chief Project Engineer Section Leader Automobile Powertrain Research
More informationContinuity in internationalization: BOGE Rubber & Plastics on track for further growth
Page 1/6, 28.04.2017 Automotive supplier reports record sales Continuity in internationalization: BOGE Rubber & Plastics on track for further growth Sales grew by 3.2 percent to EUR 763.4 million in 2016
More informationDelivery program Semi-finished plastics
Delivery program Semi-finished plastics Centroplast Engineering Plastics GmbH Engineering plastics belong to most important industrial materials. They convince above all by their level of performance and
More informationVERLON No Swell Wear Rings
VERLON No Swell Wear Rings Ultra precision +.001 tolerance on cross section NO SWELL - Lowest friction Strength to 40,000 PSI Large range of widths, cross sections and diameters - metric too Features &
More informationPRODUCTS GUIDE ENGINEERING THERMOPLASTICS FLAME RETARDANT HIGH PERFORMANCE
PRODUCTS GUIDE ENGINEERING THERMOPLASTICS FLAME RETARDANT HIGH PERFORMANCE WHO IS LATI? LATI is a company founded in Italy in 1945. Since its foundation, it has been gaining a prestigious position in the
More informationGlobal Luxury Car Market: Size, Trends & Forecasts ( ) April 2018
Global Luxury Car Market: Size, Trends & Forecasts (2018-2022) April 2018 Global Luxury Car Market: Coverage Executive Summary and Scope Introduction/Market Overview Global Market Analysis Regional Market
More informationIntroduction of Voith Composites. Meet the Future of Carbon Fiber Composites. Germany, July voith.com. Garching, June 27, 2018
voith.com Introduction of Voith Composites Germany, July 2018 Garching, June 27, 2018 Meet the Future of Carbon Fiber Composites Voith Composites Germany July 2018 1 Voith Group One of the Biggest Family
More informationAn automotive perspective on the use of carbon fibres
An automotive perspective on the use of carbon fibres Dr. Armin Plath I Dr. Olaf Täger I Timo Niederstadt I Materials and Manufacturing Processes 13.06.2012 The Challenge of CO 2 -Reduction 2 Opportunities
More informationPowertrain: New Technologies and Strategies. Contents
Contents Table of Figures... 5 Introduction... 8 Industry Drivers... 13 Legislation and regulation... 13 Sulphur... 18 Meeting consumer requirements... 20 Gasoline Engine Technology... 22 Fuel efficiency...
More informationChallenges of material development for Selective Laser Sintering. Coachulting Forum
Challenges of material development for Selective Laser Sintering Coachulting Forum 31.1.2018 Agenda About ADVANC3D Materials GmbH Status Quo of SLS Plastic Material Requirements of customers Cornerstones
More informationSelected Aspects of the Processing Stability of Polyolefins
1 Selected Aspects of the Processing Stability of Polyolefins Part 1 Polypropylene H. Kwon 1, J.Kim 1, J.Bayer 2, J. Mara 3, B.Iyer 4 & Klaus Keck 1 1 Songwon Industrial, South Korea 2 Songwon International
More informationPowerPact B. Molded case circuit breakers and switches from A
PowerPact B Molded case circuit breakers and switches from 15-125 A 2 schneider-electric.us Efficiency that clicks. PowerPact B molded case circuit breakers Schneider Electric introduces a new family member
More informationnovapress 850 Extreme adaptability. High fault tolerance. Maximum sealing performance.
novapress 850 Extreme adaptability. High fault tolerance. Maximum sealing performance. GASKETS TECHNICAL TEXTILES EXPANSION JOINTS INSULATION NEW MATERIALS A quantum leap in tightness Maximum sealing performance
More informationComponents: Dimensions / Order Codes
Light Series LB Components: Dimensions / Order Codes Clamp Body Single Design ø D 2 B ø D 3 H S ø D 1 L2 L3 Order Codes Clamp Body Standard Materials Polypropylene Colour: Black Material code: PP Polyamide
More informationisovac high-perm A
Data sheet isovac P 400-65 A page 1/6 01/2018 Electrical Steel Fully processed Data sheet isovac P 400-65 A page 1/6 01/2018 isovac high-perm 400-65 A The specialist with the highest permeability Manufactured
More informationDELO -PUR 9692 Multi-purpose 2c polyurethane, cures at room temperature, high-viscous, filled
DELO -PUR 9692 Multi-purpose 2c polyurethane, cures at room temperature, high-viscous, filled Base - polyurethane - two-component Use - for the bonding of metal, plastic and sometimes even elastomers -
More informationComponents: Dimensions / Order Codes Clamp Body. * 1st part of STAUFF Group 4. * Exact outside diameters Ø D1 / Ø D2 (mm) Clamp Body.
Components: Dimensions / Order Codes Clamp Body Clamp Body Colour: Green Material code: PP 4 PP One clamp body is consisting of two clamp halves. 1st part of STAUFF 4 Exact outside diameters Ø D1 / Ø D2
More informationOverview. 1. About UQM 2. The market 3. Market strategy 4. Financials
Overview 1. About UQM 2. The market 3. Market strategy 4. Financials About UQM About UQM Design and manufacture propulsion systems for electric vehicles Founded in 1967 Based in Longmont, Colorado Transportation
More informationThe xev Industry Insider Report
The xev Industry Insider Report November 2017 REPORT OUTLINE I. xev Market Trends 1. Overview Market Drivers Recent EV-Market Boosters Until Tesla, most automakers had introduced subcompact and city EVs
More informationHigh efficient SI-engine with ultra high injection pressure Chalmers University]
High efficient SI-engine with ultra high injection pressure [Research @ Chalmers University] Event; Energirelaterad forskning, 2017 Gothenburg, Sweden 5 th October 2017 Peter Granqvist President DENSO
More informationDSM Elastomers Presentation at the VKRT
THE Global Innovative EPDM Supplier Innovation @ DSM Elastomers Presentation at the VKRT Maurits F.H. van Tol DSM Elastomers Vice-President, Global Research and Development February 12th, 2009 Outline
More informationStandard Classification System for Polyamide Molding and Extrusion Materials (PA) 1
Designation: D 6779 05 Stard Classification System for Polyamide Molding Extrusion Materials (PA) 1 This stard is issued under the fixed designation D 6779; the number immediately following the designation
More informationSVENSK STANDARD SS-EN :2005. Härdplastmattor Specifikation för valsmatta (SMC) och bulkmassa (BMC) Del 3: Särskilda krav
SVENSK STANDARD SS-EN 14598-3:2005 Fastställd 2005-06-14 Utgåva 1 Härdplastmattor Specifikation för valsmatta (SMC) och bulkmassa (BMC) Del 3: Särskilda krav Reinforced thermosetting moulding compounds
More informationComponents: Dimensions / Order Codes. Clamp Body * *1*06*PP * * * * Clamp Body. ød2. Pipe / Tube / Hose Bore (1 Clamp Body)
ød Components: Dimensions / Order Codes Clamp Body ød B H L L L Clamp Body Colour: Green Material code: PP Colour: Black Material code: PA See page A88 for material properties and technical information.
More informationFuels to Enable More Efficient Engines
Fuels to Enable More Efficient Engines Robert L. McCormick & Bradley T. Zigler 4 th International Conference on Biofuels Standards: Current Issues, Future Trends Gaithersburg, Maryland, USA November 13,
More informationThe right chain! Approved Performance from Rexnord. Double pitch roller chains. MODULE_05/GB/2014/08 // No liability accepted for misprints or errors!
Approved Performance from Rexnord Double pitch roller chains Double pitch roller chains Fulfils ISO quality requirements Inner plate Hardened and tempered Roller Seamless Outer plate Hardened and tempered
More informationAs the first manufacturer, Röchling offers semi-finished products made of flame-retardant polyamide 6
As the first manufacturer, Röchling offers semi-finished products made of flame-retardant polyamide 6 With SUSTAMID 6 FR, large-size machined components and short runs are now possible Lahnstein With SUSTAMID
More informationPE-HDXc pipes (physically cross-linked polyethylene pipes)
pipes (physically cross-linked polyethylene pipes) Applications: Domestic drinking water installations, radiator connections and surface regulation Special properties high chemical resistance (according
More informationEFFECT OF TYRE OVERLOAD AND INFLATION PRESSURE ON ROLLING LOSS & FUEL CONSUMPTION OF AUTOMOBILES CARS
EFFECT OF TYRE OVERLOAD AND INFLATION PRESSURE ON ROLLING LOSS & FUEL CONSUMPTION OF AUTOMOBILES CARS D.MADHUSUDHANA 1 C. NAGARAJA 2 PG Student Assistant Professor Dept. of Mechanical Engineering Dept.
More information