Vegetable based lubricating & degreasing solvent with high solvent power

Transcription

1 Vegetable based lubricating & degreasing solvent with high solvent power PRODUCT DESCRIPTION IMPACT is Vegetable based degreasing solvent with high solvent power, demonstrated by a Kauri Butanol index (KBI) of 180. IMPACT is unique, with high cleaning and dissolving power and high wettability; extremely high solubility parameters and cohesion forces, for effective dissolution and removal of most organic and inorganic pollutants, including inks and fresh resins. IMPACT has excellent lubricant and anti wear properties. Friction test (SRV) result of 0.12, means that IMPACT helps to reduce energy consumption, disassembly effort and operating noise levels. Strong penetrating power with low surface tension: 23,4 Dynes/cm and confirmed, powerful deoxidising power, tested according to MIL A 907 ED, loosening torque 12Nm. IMPACT can also be used as a cleaner to remove tar provides instant tar removal as per Asphalt removal test: 40 g at 20 C, 3'15 ANTI-CORROSION ACTION: most manufacturers and aerosol packagers of penetrating, deoxidising fluids and releasing agents, claim anti-corrosion properties to their products. However, the anti-corrosion performance of a product is defined by the ISO 9227 and ISO standards; therefore, such products need to be tested and evaluated quantitatively. This is not usually seen on other products. The anticorrosion properties of those products are usually negligible. ibiotec IMPACT, leaves a non-photosensitive anti-oxygen film, without desiccation, and thus protects against corrosion during a short period of time. Just as most other products on the market, its purpose is not to protect metals against atmospheric, chemical or thermal attack in the long term. In all cases, it is preferable to use a specific product for that purpose.

2 INSTRUCTIONS FOR USE Shake the aerosol briefly, in an up-and-down movement. Spray the surfaces that are to be treated from a distance of 20 cm, depending on their size. Aerosol usable in any position, even upside down. Use the appropriate nozzle for the job, shake the aerosol for a few seconds, spray on surfaces being treated. If needed, wipe with a damp cloth after treatment. Caution: Following cleaning or in case of accidental spilling, floors can get slippery; rinse with water. IMPACT is also a lubricant. Do not use on transmission belts or as a brake cleaner. IMPACT aerosol is usable in all positions. Valves specifically designed and patented by ibiotec. Aerosol guaranteed not to have butane-propane propellant, which is highly flammable, explosive, and subject to storage and handling regulations. Most common source of accidents reported by the insurance companies.

3 PHYSICO-CHEMICAL CHARACTERISTICS Appearance Visual Clear - Colour Visual Amber - Odour Olfactory None - Density at 25 C NF EN ISO kg/m 3 Refraction index ISO Freezing point ISO C Water solubility - Partial, rinsable % Kinematic viscosity at 40 C NF EN mm²/s Acid value EN N/M mg KOH/g Iodine value NF EN N/M g I 2 /100g Water content NF ISO ppm Residue following rinsing with water NF T % PERFORMANCE CHARACTERISTICS AS A DEGREASING SOLVENT KB index ASTM D Evaporation rate - N/A min Surface tension at 20 C ISO Dyne/cm Breakdown voltage IEC Volts Copper blade corrosion, 100 h at 40 C PERFORMANCE CHARACTERISTICS AS A LUBRICANT ISO a Class Friction test, SRV ASTM D Coefficient

4 Shell four-ball tester - Wear scar diameter Shell four-ball tester - Wear loading Friction test, fretting wear, 1.7 m/sec at 98 N IP 239 ASTM D 2596 IP 239 ASTM D mm 3200 dan REICHERT Under testing - Potential noise reduction GRW method - 60 db Press fit test Under testing Stamping test - Erichsen ISO Under testing RIG test for electrical contacts FIRE SAFETY CHARACTERISTICS Under testing Flash point (closed cup) ISO 2719 > 100 C Autoignition temperature ASTM E 659 > 230 C Lower explosive limit NF EN % (volume) Upper explosive limit NF EN % (volume) Content of explosive, oxidising, flammable, or very/extremely flammable substances TOXICOLOGICAL CHARACTERISTICS CLP regulation 0 % Anisidine value NF ISO 6885 < 6 - Peroxide value NF ISO 3960 < 10 meq(o 2 )/kg TOTOX (Anisidine index +2x Peroxyde index) - < 26 - Content of CMR, irritant and CLP regulation 0 %

5 corrosive substances Content of residual methanol derived from transesterification processes Emissions of hazardous, CMR, irritant, corrosive compounds at 160 C. ENVIRONMENTAL CHARACTERISTICS GC-MS 0 % GC-MS 0 % Water hazard WGK Germany 1 Class Primary biodegradability, CEC 21 days at 25 C Ready biodegradability L 33 T 82 Higher than 90 % OCDE 301 A over a 28-day period COD disappearance Ready and ultimate biodegradability ISO 7827 Higher than 80 % OCDE 310 C over a 28-day period Biodegradation after 69 days Modified MITI Higher than % % Bioaccumulation Partition index (noctanol/water) OCDE 107 Lower than 3 log KOW Vapour pressure at 20 C NF EN < 0.1 hpa VOC concentration (Volatile Organic Compounds) - 0 %

6 Sulphur content Bomb calorimeter GC MS < 200 ppm Benzene content ASTM D % Total halogen content Bomb calorimeter GC MS Chlorinated solvent content - 0 Aromatic solvent content - 0 Content of substances hazardous to the environment Content of compounds with non-zero GWP Content of compounds with non-zero ODP Carbon balance, life cycle analysis. < 200 ppm CLP regulation 0 % - 0 % - 0 % ISO * N/M: Not measured or non-measurable N/A: Not applicable Kg, carbon equivalent

7 PRESENTATION IMPACT is presented in non flammable Aerosol can 650ml, and packed in cartons of 2 cans. ibiotec Tec Industries Service is certified ISO 9001 ISO OHSAS SMI