|
|
- Norman Austin
- 6 years ago
- Views:
Transcription
1 Page 1 of Ford F450 Super Duty 6.7L Eng Service Manual: ENGINE MECHANICAL - 6.7L DIESEL -- F250-F550 SUPER DUTY IN-VEHICLE REPAIR > OIL PAN - LOWER MATERIAL SPECIFICATIONS Item Motorcraft SAE 0W-30 Super All Season Motor OilXO-0W30-LAS Motorcraft SAE 5W-40 Full Synthetic Diesel Motor OilXO-5W40-5QSD Motorcraft SAE 10W-30 Super Duty Diesel Motor OilXO-10W30-QSD Motorcraft SAE 15W-40 Super Duty Diesel Motor OilXO-15W40-QSD (US); CXO-15W40-LSD12 (Canada) Silicone Gasket and SealantTA-30 Specification WSS-M2C171-E WSS-M2C171-E WSS-M2C171-E WSS-M2C171-E WSE-M4G323- A4 IN-VEHICLE REPAIR > OIL PAN - LOWER > REMOVAL 1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to JACKING & LIFTING. 2. Drain the engine oil. 1. On late build vehicles, tighten to 26 Nm (19 lb-ft). 3. Remove the 15 bolts and the lower oil pan. 1. On early build vehicles, remove and discard the gasket. 2. On late build vehicles, clean and inspect the sealing surfaces.
2 Page 2 of 8 Fig 1: Locating Lower Oil Pan And Bolts IN-VEHICLE REPAIR > OIL PAN - LOWER > INSTALLATION Late build vehicles 1. Apply a 3.4 mm (0.133 in) diameter bead of sealant 1.0 mm (0.039 in) outward of the chamfer on the lower oil pan sealing face.
3 Page 3 of 8 Fig 1: Identifying Sealant Applying Area Of Chamfer On Lower Oil Pan Sealing Face All vehicles NOTE: On early build vehicles, install a new gasket.
4 Page 4 of 8 Fig 2: Identifying Lower Oil Pan Bolts Tightening Sequence 2. Install the lower oil pan and the 15 bolts. Tighten in the sequence shown. 1. Tighten to 10 Nm (89 lb-in). 3. Fill the engine with the correct engine oil for the climate. Refer to the Engine for additional oil and fill information. IN-VEHICLE REPAIR > OIL PAN - UPPER MATERIAL SPECIFICATIONS Item Silicone Gasket and SealantTA-30 Specification WSE-M4G323-A4 IN-VEHICLE REPAIR > OIL PAN - UPPER > UPPER OIL PAN
5 Page 5 of 8 Fig 1: Exploded View Of Upper Oil Pan Item Part Number Description Oil pan gasket Upper oil pan 3 W Upper oil pan bolt (5 required) 4 W Upper oil pan bolt (18 required) 5 W Upper oil pan bolt (2 required) IN-VEHICLE REPAIR > OIL PAN - UPPER > REMOVAL 1. Remove the oil level indicator. 2. Remove the flexplate. For additional information refer to Flexplate. 3. Remove the oil cooler. For additional information, refer to Oil Cooler.
6 Page 6 of 8 4. Remove and discard the oil filter. 5. Disconnect the Engine Oil Temperature (EOT) sensor and Engine Oil Pressure (EOP) switch electrical connectors. 6. Remove the nut from the oil filter header and position aside the engine wire harness. 7. Remove the nut and position aside the transmission cooler tubes. 8. Remove the nut and position aside the side engine wire harness. 9. Remove the 2 nuts from the front of the engine and position the engine wire harness aside. 10. Remove the 25 bolts and the upper oil pan. 1. Remove and discard the gasket. 2. Clean and inspect the sealing surfaces. IN-VEHICLE REPAIR > OIL PAN - UPPER > INSTALLATION 1. Install a new gasket in the upper oil pan. 2. Apply a dime-sized bead of sealant at the 4 cover joints. Fig 1: Locating Upper Oil Pan Gasket NOTE: Final torque must be reached within 30 minutes of sealant application.
7 Page 7 of 8 Fig 2: Identifying Upper Oil Pan Bolts Tightening Sequence 3. With the help of an assistant, install the upper oil pan and 25 bolts. Tighten in 2 stages in the sequence shown. 1. Stage 1: Tighten to 2 Nm (18 lb-in). 2. Stage 2: Tighten to 24 Nm (18 lb-ft). 4. Position the front wire harness and install the 2 nuts. 1. Tighten to 12 Nm (106 lb-in). 5. Position the side wire harness and install the nut. 1. Tighten to 12 Nm (106 lb-in). 6. Position the transmission cooler tubes and install the nut. 1. Tighten to 12 Nm (106 lb-in). 7. Position the engine wire harness at the oil filter header and install the nut. 1. Tighten to 12 Nm (106 lb-in). 8. Connect the EOP switch and EOT sensor electrical connectors. 9. Install a new oil filter.
8 Page 8 of Install the oil cooler. For additional information, refer to Oil Cooler. 11. Install the flexplate. For additional information refer to Flexplate. 12. Install the oil level indicator.
2010 Explorer, Mountaineer, Explorer Sport Trac Workshop Manual. IN-VEHICLE REPAIR Procedure revision date: 06/11/2009
SECTION 303-01B: Engine - 4.6L 2010 Explorer, Mountaineer, Explorer Sport Trac Workshop (3V) Manual IN-VEHICLE REPAIR Procedure revision date: 06/11/2009 Engine Lubrication Components - Exploded View Brackets,
More information2006 Freestar/Monterey Workshop Manual. IN-VEHICLE REPAIR Procedure revision date: 12/01/2005
SECTION 303-01: Engine 3.9L and 4.2L IN-VEHICLE REPAIR Procedure revision date: 12/01/2005 Valve Cover LH Item Part Number Description 1 W708650 Oil level indicator tube bolt 2 6754 Oil level indicator
More informationIN-VEHICLE REPAIR. Engine Front Cover
303-01A-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01A-1 Special Tool(s) SAE 5W-20 Premium WSS-M2C930-A Synthetic Blend Motor Oil Alignment Plate, Camshaft XO-5W20-QSP (in Canada
More informationSECTION C Engine 5.4L (3V)
303-01C-i Engine 5.4L (3V) 303-01C-i SECTION 303-01C Engine 5.4L (3V) CONTENTS PAGE IN-VEHICLE REPAIR Engine Front Cover... 303-01C-2 303-01C-2 Engine 5.4L (3V) 303-01C-2 IN-VEHICLE REPAIR Engine Front
More informationIN-VEHICLE REPAIR. Engine Front Cover
303-01B-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01B-1 Special Tool(s) Motorcraft SAE 5W-20 WSS-M2C930-A Premium Synthetic Blend 3-Jaw Puller Motor Oil 303-D121 XO-5W20-QSP
More informationIN-VEHICLE REPAIR. Oil Pan Lower. Removal. 2. Disconnect the LH and RH battery ground cables. For additional information, refer to Section
303-01C-1 IN-VEHICLE REPAIR Oil Pan Lower Special Tool(s) 3-Bar Engine Support 303-F070 Lifting Eyes 303-D030 303-01C-1 2. Disconnect the LH and RH battery ground cables. For additional information, refer
More informationEngine Front Cover. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Installer, Front Cover Oil Seal (T88T-6701-A)
SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/23/2008 Engine Front Cover Special Tool(s) 3-Jaw Puller 303-D121 or equivalent Installer, Front
More information2006 Expedition/Navigator Workshop Manual
7. Remove the RH variable camshaft timing (VCT) oil control solenoid. For additional information, refer to Section 303-14. 8. Remove the RH ignition coils. For additional information, refer to Section
More informationEngine Front Cover. Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1) or equivalent. Support Bar, Engine 303-F070
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Engine Front Cover Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1)
More informationCrankshaft Rear Seal with Retainer Plate
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Crankshaft Rear Seal with Retainer Plate Special Tool(s) Installer, Crankshaft Rear
More informationWSS-M2C931- B. 1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Oil Filter Adapter Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1)
More information2006 Ford Pickup F350 Super Duty
CYLINDER HEAD - RH SPECIAL TOOLS REFERENCE Lifting Bracket, Cylinder Head 303-759 Heavy Duty Floor Crane 014-00071 Wednesday, January 28, 2009 1:47:28 1:47:34 PM Page 1 2005 Mitchell Repair Information
More information11/29/2017 Engine Cooling - Coolant Pump - Removal and Installation 2010 Ford Edge MotoLogic Engine Cooling 2010 Edge, MKX
2010 Edge Report a problem with this article 303-03 Engine Cooling 2010 Edge, MKX REMOVAL AND INSTALLATION Procedure revision date: 10/04/2010 Coolant Pump Special Tool(s) Camshaft Holding Tool 303-1248
More informationPage 1 of 8 303-01A Engine 2.3L 2007 Escape/Mariner/Escape Hybrid/Mariner Hybrid IN-VEHICLE REPAIR Procedure revision date: 10/05/2008 Cylinder Head Special Tool(s) Alignment Plate, Camshaft 303-465 (T94P-6256-CH)
More informationPage 1 of 5 303-01B Engine 3.0L (4V) 2004 Escape IN-VEHICLE REPAIR Procedure revision date: 05/26/2005 Engine Front Cover Material Removal Item Motocraft Metal Surface Cleaner ZC-21 Silicone Gasket and
More informationIN-VEHICLE SERVICING > VALVE COVER - RH
Page 1 of 20 Service Manual: ENGINE - 5.4L (3V)- F-150 & MARK LT IN-VEHICLE SERVICING > VALVE COVER - RH 2008 Ford Pickup 5.4L Eng F150 Material Item Specification Motorcraft Metal Surface Prep ZC-31 PAG
More informationSECTION B Engine 5.0L (4V)
303-01B-i Engine 5.0L (4V) 303-01B-i SECTION 303-01B Engine 5.0L (4V) CONTENTS PAGE SPECIFICATIONS... 303-01B-2 303-01B-2 Engine 5.0L (4V) 303-01B-2 SPECIFICATIONS Material Motorcraft Metal Surface Prep
More informationREMOVAL AND INSTALLATION
303-04C-1 REMOVAL AND INSTALLATION Fuel Injectors Special Tool(s) Caps, Fuel System 310-158 Special Tool(s) 303-04C-1 Holding Rack, Fuel Injector 303-D114 (D94T-9000-E1) Cups, Fuel Injector 303-1261 Tool,
More informationIN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent
303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent
More informationSECTION A Engine 3.7L
303-01A-i Engine 3.7L 303-01A-i SECTION 303-01A Engine 3.7L CONTENTS PAGE SPECIFICATIONS... 303-01A-2 303-01A-2 Engine 3.7L 303-01A-2 SPECIFICATIONS Material Motorcraft High Performance Engine RTV Silicone
More informationSECTION D Fuel Charging and Controls Turbocharger
303-04D-i Fuel Charging and Controls Turbocharger 303-04D-i SECTION 303-04D Fuel Charging and Controls Turbocharger CONTENTS PAGE Turbocharger... 303-04D-2 303-04D-2 Fuel Charging and Controls Turbocharger
More informationEngine. Special Tool(s) Adapter for (T97T-6256-A) Adapter for (T97T-6256-D)
SECTION 303-01A: Engine 4.0L SOHC 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 05/10/2010 Engine Special Tool(s) Adapter for 303-564 303-578 (T97T-6256-A) Adapter for 303-577 303-576
More information2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.
2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position
More information8/28/2018 Engine 6.0L Diesel - Cylinder Head RH - in Vehicle Repair 2006 Ford F-550 MotoLogic. Specification
2006 F-550 Applies to: 6.0L Diesel Report a problem with this article SECTION 303-01C: Engine 6.0L Diesel 2006 F-Super Duty 250-550 Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/03/2006
More informationEngine 3.5L 2010 Edge, MKX. SPECIFICATIONS Procedure revision date: 08/26/2013. Specification. Item Specification Fill Capacity
2010 Edge Report a prolem with this article 303-01 Engine 3.5L 2010 Edge, MKX SPECIFICATIONS Procedure revision date: 08/26/2013 s Material Fill Capacity Motorcraft High Performance Engine RTV Silicone
More information2011 Mercury Grand Marquis LS
Fig. 6: Locating Intake Manifold Crash Bracket With Tie Strap 24. Remove the intake manifold crash bracket bolt. 25. Disconnect the fuel rail pressure and temperature sensor vacuum and electrical connectors.
More informationSECTION D Fuel Charging and Controls Turbocharger
303-04D-i Fuel Charging and Controls Turbocharger 303-04D-i SECTION 303-04D Fuel Charging and Controls Turbocharger CONTENTS PAGE Turbocharger Body On... 303-04D-2 303-04D-2 Fuel Charging and Controls
More information2004 F-150 Workshop Manual
Page 1 of 8 SECTION 303-01B: Engine 5.4L (3V) 2004 F-150 Workshop Manual REMOVAL Procedure revision date: 02/10/2004 Engine Printable View (943 KB) Special Tool(s) Modular Engine Lift Bracket 303-F047
More informationSECTION C Engine 6.4L Diesel
303-01C-i Engine 6.4L Diesel 303-01C-i SECTION 303-01C Engine 6.4L Diesel CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 6.4L Diesel 303-01C-2 SPECIFICATIONS Material Gasket Maker TA-16 Motorcraft
More informationASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s)
303-01A-1 ASSEMBLY Engine Special Tool(s) Tensioner, Timing Chain 303-571 (T97T-6K254-A) Special Tool(s) 303-01A-1 Installer, Crankshaft Vibration Damper 303-102 (T74P-6316-B) Holding Tool, Camshaft Sprocket
More informationWSS- M97B51-A1 WSS- M2C930-A. 5.7L (6 qt) with filter WSE- M4G323-A4
SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual SPECIFICATIONS Procedure revision date: 01/22/2009 Material Item Specification Fill Capacity Gasket Maker TA-16 WSK- M2G348-A5 Motorcraft
More informationIN-VEHICLE REPAIR. Main Control Valve Body. Removal. 6. Disconnect the transaxle wiring harness electrical connector and TR sensor connector.
307-01-1 Automatic Transaxle/Transmission 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Material Item Thread Sealant with PTFE TA-24 Motorcraft MERCON Multi-Purpose (ATF) Transmission Fluid XT-2-QDX
More information2003 F-Super Duty /Excursion Workshop Manual
Page 1 of 7 SECTION 303-04F: Fuel Charging and Controls Turbocharger, 6.0L Diesel 2003 F-Super Duty 250-550/Excursion Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Turbocharger
More information2006 F-Super Duty Workshop Manual. Installation. All vehicles. Install the glow plug. Tighten to 19 Nm (14 lb-ft).
Installation All vehicles 1. Install the glow plug. Tighten to 19 Nm (14 lb-ft). 2. Clean and apply clean engine oil to the O-rings. 3. Using the special tool, install the glow plug harness. Vehicles equipped
More information1 of 14 11/19/ :45 AM
1 of 14 11/19/2016 11:45 AM 6F35 Digital Transmission Range (TR) Sensor Removal All vehicles 1. With the vehicle in NEUTRAL, position it on a hoist. 3.0L engine 2. Remove the Air Cleaner (ACL) outlet pipe.
More information2/13/2018 Engine 3.0L (4V) - Valve Cover RH - in Vehicle Repair 2006 Lincoln Zephyr MotoLogic
2006 Zephyr Applies to: 3.0L (4V) Report a problem with this article SECTION 303-01B: Engine 3.0L (4V) 2006 Fusion/Milan/Zephyr Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/24/2006 Valve
More information2007 Explorer/Mountaineer/Explorer Sport Trac Workshop Manual SECTION A: Engine 4.0L SOHC. IN-VEHICLE REPAIR Procedure revision date: 04/20/2006
SECTION 303-01A: Engine 4.0L SOHC 2007 Explorer/Mountaineer/Explorer Sport Trac Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 04/20/2006 Camshaft Drive Cassette LH Printable View (577 KB)
More informationOIL PUMP (G306709) DISCOVERY 3, ENGINE - TDV6 2.7L DIESEL SPECIAL TOOL(S) Crankshaft Front Seal Remover PUMP - OIL - RENEW
2005.0 DISCOVERY 3, 303-01 ENGINE - TDV6 2.7L DIESEL OIL PUMP (G306709) IN-VEHICLE REPAIR 12.60.26 PUMP - OIL - RENEW 2700 CC 4.3 USED WITHINS SPECIAL TOOL(S) 303-1120 Crankshaft Front Seal Remover 303-1122
More informationSECTION C Engine 6.0L Diesel
303-01C-i Engine 6.0L Diesel 303-01C-i SECTION 303-01C Engine 6.0L Diesel CONTENTS PAGE IN-VEHICLE REPAIR Cylinder Head RH... 303-01C-2 303-01C-2 Engine 6.0L Diesel 303-01C-2 IN-VEHICLE REPAIR Cylinder
More informationIN-VEHICLE REPAIR. Upper Intake Manifold
303-01-1 Engine 3.9L and 4.2L 303-01-1 IN-VEHICLE REPAIR Upper Intake Manifold Special Tool(s) Remover, Spark Plug Wire 303-106 (T74P-6666-A) Material Item Silicone Brake Caliper Grease and Dielectric
More informationCylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty
More informationTransmission Diesel Engines
Page 1 of 17 SECTION 307-01B: Automatic Transaxle/Transmission TorqShift 6 2011 F-250, 350, 450, 550 Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 11/12/2010 Transmission
More informationIN-VEHICLE REPAIR. Camshaft RH. Removal. 2. Remove the RH valve cover. For additional information, refer to Valve Cover RH in this section.
303-01B-1 IN-VEHICLE REPAIR Camshaft RH Special Tool(s) Compressor, Valve Spring 303-1039 Wedge, Timing Chain 303-1175 303-01B-1 2. Remove the RH valve cover. For additional information, refer to Valve
More information2002 Crown Victoria/Grand Marquis Workshop Manual
Page 1 of 24 SECTION 303-01: Engine 2002 Crown Victoria/Grand Marquis Workshop Manual INSTALLATION Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Installer, Crankshaft Vibration Damper
More informationIN-VEHICLE REPAIR. Timing Drive Components. Removal. 3. Position the crankshaft keyway at the 12 o clock position.
303-01B-1 IN-VEHICLE REPAIR Timing Drive Components 303-01B-1 Special Tool(s) Compressor, Valve Spring 303-1039 Locking Tool, Camshaft Phaser Sprocket 303-1046 3. Position the crankshaft keyway at the
More informationIntake Components 1117
Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold
More informationPage 1 of 18 303-01C Engine 5.4L (3V) 2010 F-150 IN-VEHICLE REPAIR Procedure revision date: 07/01/2009 Timing Drive Components Special Tool(s) Compressor, Valve Spring 303-1039 Holding Tool, Crankshaft
More informationINSTALLATION. Engine. All vehicles. 1. Install the special tool to the threaded hole located at the LH side of the engine block.
303-01B-1 INSTALLATION Engine 303-01B-1 Special Tool(s) 3-Bar Engine Support Kit 303-F072 Lifting Brackets, Engine 303-050 (T70P-6000) Modular Engine Lift Bracket 303-F047 (014-00073) or equivalent 2.
More informationPage 1 of 14 Oil Pan Removal & Installation 4.2L Engine 4WD Vehicles To Remove: 1. Before servicing the vehicle refer to the precautions at the beginning of this section. 2. Raise and support the vehicle.
More informationIN-VEHICLE REPAIR. Camshaft RH. Removal. 2. Remove the RH valve cover. For additional information, refer to Valve Cover RH in this section.
303-01C-1 IN-VEHICLE REPAIR Camshaft RH Special Tool(s) 303-01C-1 2. Remove the RH valve cover. For additional information, refer to Valve Cover RH in this section. Compressor, Valve Spring 3. NOTICE:
More informationIN-VEHICLE REPAIR. Timing Drive Components. Removal. 3. Position the crankshaft keyway at the 12 o clock position.
303-01C-1 IN-VEHICLE REPAIR Timing Drive Components 303-01C-1 Special Tool(s) Compressor, Valve Spring 303-1039 Locking Tool, Camshaft Phaser Sprocket 303-1046 3. Position the crankshaft keyway at the
More information2003 Taurus/Sable Workshop Manual
Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)
More informationfile://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref...
Page 1 of 41 SECTION 303-01B: Engine 4.6L and 5.4L 2000 F-150 Workshop Manual ASSEMBLY Procedure revision date: 01/27/2004 Engine 4.6L Special Tool(s) Compressor, Valve Spring 303-567 (T97P-6565-AH) Compressor
More informationPage 1 of 75 303-01D Engine - 5.2L 32V Ti-VCT 2016 Mustang Assembly Procedure revision date: 12/15/2016 Special Tool(s) / General Equipment Engine Base Part Number: 6L084 205-142 (T80T-4000-J) Installer,
More informationEngine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH)
Page 1 of 41 SECTION 303-01A: Engine 5.4L (2V) 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual ASSEMBLY Procedure revision date: 04/04/2003 Engine Special Tool(s) Compressor,
More informationTiming Drive Components
2006 Ford F 150 : Engine Mechanical > Engine, 5.4L (3V) > IN VEHICLE REPAIR > Timing Drive Components Timing Drive Components Listen SECTION 303 01C: Engine 5.4L (3V) 2006 F 150/Mark LT Workshop Manual
More information2009 Mustang Workshop Manual. REMOVAL AND INSTALLATION Procedure revision date: 05/23/2008
Fuel Rail Pressure and Temperature Sensor - 4.0L SOHC Material Item Motorcraft SAE 5W-30 Premium Synthetic Blend Motor Oil XO-5W30-QSP (US); Motorcraft SAE 5W-30 Super Premium Motor Oil CXO-5W30-LSP12
More informationSECTION C Engine 5.4L (4V)
303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 SPECIFICATIONS Material Motorcraft Metal Surface Prep
More informationPage 1 of 23 303-01C Engine - 3.2L Duratorq-TDCi (148kW/200PS) - Puma 2011-2014 Ranger Assembly Procedure revision date: 07/21/2016 Special Tool(s) / General Equipment Engine Base Part Number: 6L084 100-002
More information2010 Town Car Workshop Manual. REMOVAL AND INSTALLATION Procedure revision date: 08/20/2009
SECTION 502-02: Full Frame and Body Mounting REMOVAL AND INSTALLATION Procedure revision date: 08/20/2009 Crossmember - Number 2 Special Tool(s) Engine Support Bar 303-F072 Support Bracket, Engine 303-639
More informationINSTALLATION. Engine. All vehicles. 1. Install the special tool to the threaded hole located at the LH side of the engine block.
303-01B-1 INSTALLATION Engine 303-01B-1 Special Tool(s) 3-Bar Engine Support Kit 303-F072 Lifting Brackets, Engine 303-050 (T70P-6000) Modular Engine Lift Bracket 303-F047 (014-00073) or equivalent 2.
More informationCylinder Block Cradle
SECTION 303-01A: Engine 4.0L SOHC 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 01/27/2010 Cylinder Block Cradle Special Tool(s) Lifting Bracket, Engine 303-050 (T70P-6000) Support
More information1998 Ford EXPEDITION. Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS. Transmission
1998 Ford EXPEDITION Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS SECTION 307-01C: Automatic Transmission 4R100 1998 Expedition/Navigator Workshop Manual REMOVAL Procedure revision
More informationEngine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,
More informationSECTION C Engine 5.4L (3V)
303-01C-i Engine 5.4L (3V) 303-01C-i SECTION 303-01C Engine 5.4L (3V) CONTENTS PAGE IN-VEHICLE REPAIR Timing Drive Components... 303-01C-2 303-01C-2 Engine 5.4L (3V) 303-01C-2 IN-VEHICLE REPAIR Timing
More information2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar
COWL TOP VENT PANEL 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top
More information2011 Flex Workshop Manual. REMOVAL AND INSTALLATION Procedure revision date: 05/10/2010
SECTION 303-14: Electronic Engine Controls REMOVAL AND INSTALLATION Procedure revision date: 05/10/2010 Knock Sensor (KS) - 3.5L GTDI NOTE: LH cylinder head removed from art for clarity. Item Part Number
More informationPage 1 of 8 Section 03-01: Engine, 4.6L IN-VEHICLE SERVICE 1994 Town Car/Crown Victoria/Grand Marquis Workshop Manual Oil Pan and Oil Pump Screen Cover and Tube Town Car Removal 1. Disconnect battery ground
More information1999 E-Series Workshop Manual
http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998
More informationTiming Drive Components
IN VEHICLE REPAIR: TIMING DRI... IN VEHICLE REPAIR: TIMING DRIVE COMPONENTS (ENGINE 5.4L (3V)) 303 01B Engine 5.4L (3V) 2004 F 150 IN VEHICLE REPAIR Procedure revision date: 03/14/2006 Timing Drive Components
More informationValve Cover - RH Material
1 of 5 5/15/2015 8:06 AM Valve Cover - RH Material 2 of 5 5/15/2015 8:06 AM 3 of 5 5/15/2015 8:06 AM Removal CAUTION: During engine repair procedures, cleanliness is extremely important. Any foreign material,
More informationFUEL PUMP CAMSHAFT TIMING CHECK
PUBLISHED: 26-FEB-2018 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING CHECK (G1473740) GENERAL PROCEDURES 19.90.16 HIGH PRESSURE FUEL TIMING CHECK 5000 CC,
More informationPage 1 of 9 SECTION 303-01B: Engine 2.0L SPI 2002 Focus Workshop Manual ASSEMBLY Procedure revision date: 12/14/2000 Engine Special Tool(s) Crankshaft Rear Seal Pilot 303-329 (T88P-6701-B2) Crankshaft
More informationDESCRIPTION AND OPERATION > TRANSAXLE DESCRIPTION
Page 1 of 10 2006 Mercury Montego 3.0L Eng Premier Service Manual: AUTOMATIC TRANSMISSION - CVT Print Date: DESCRIPTION AND OPERATION > TRANSAXLE DESCRIPTION This transaxle represents the start of a new
More informationBD PERFORMANCE TRANSMISSION
1 BD PERFORMANCE TRANSMISSION 2008-10 F o r d 6. 4 L ( 5 R 1 1 0 ) I n s t a l l a t i o n I n s t r u c t i o n s 4WD Part # 1064494 2WD Part # 1064492 Please read the instructions and warranty disclaimer
More informationIN-VEHICLE REPAIR. Output Shaft Speed (OSS) Sensor. Removal
307-01-1 Automatic Transaxle/Transmission 6F50 307-01-1 IN-VEHICLE REPAIR Output Shaft Speed (OSS) Sensor Material Item MERCON V Automatic Transmission Fluid XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada)
More information2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...
Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine
More informationFUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G )
PUBLISHED: 10-OCT-2017 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G1473741) GENERAL PROCEDURES 19.90.17 HIGH PRESSURE FUEL TIMING CHECK AND
More informationASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 39 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:08 PM To: 'Evan Groenke' Subject: 2.5L Engine Re-assembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
More information2005 Ford Pickup F250 Super Duty. SPECIAL TOOLS Release Tool, Injector Connector
FUEL INJECTORS SPECIAL TOOLS Release Tool, Injector Connector 303-1115 MATERIAL Item Specification SAE 15W-40 Super Duty Motor Oil XO-15W40-QSD or equivalent WSS-M2C171-D Metal Brake Parts Cleaner PM-4
More information2002 F-150 Workshop Manual
Page 1 of 8 SECTION 307-01B: Automatic Transmission 4R70W 2002 F-150 Workshop Manual REMOVAL Procedure revision date: 04/02/2003 Transmission Special Tool(s) Retainer, Torque Converter 307-346 (T97T-7902-A)
More informationDESCRIPTION AND OPERATION
303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589
More informationPage 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description
More informationM-2300-T 6-Piston Mustang Brake Kit INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationBD PERFORMANCE TRANSMISSION
1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD PERFORMANCE TRANSMISSION 2008-10 F o r d 6. 4 L ( 5 R 1 1 0 ) I n s t a l l a t i o n I n s t r u c t i o n s 4WD Part # 1064494 2WD Part
More informationALLDATA Online - 1997 Ford Truck F 150 2WD Pickup V8-5.4L SOHC VIN L - Servi... Page 1 of 22 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference
More information1995 Aerostar/Ranger/Explorer
Page 1 of 13 Section 03-01C: Engine, 4.0L V-6 DISASSEMBLY AND ASSEMBLY 1995 Aerostar/Ranger/Explorer Workshop Manual Engine Disassembly 1. NOTE: Before starting disassembly, remove all wiring harnesses,
More informationSECTION Automatic Transaxle/Transmission 4R70E/4R75E
307-01-i Automatic Transaxle/Transmission 4R70E/4R75E 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 4R70E/4R75E CONTENTS PAGE Transmission Four Wheel Drive (4WD)... 307-01-2 307-01-2 Automatic
More information1999 Explorer/Mountaineer Workshop Manual
Page 1 of 5 SECTION 307-01B: Automatic Transmission 5R55E 1999 Explorer/Mountaineer Workshop Manual REMOVAL Procedure revision date: 07/27/1998 Transmission Special Tool(s) Torque Converter Holding Tool
More informationPiston Cooling Nozzle, Replacement
Volvo Trucks North America Greensboro, NC USA This Service Bulletin replaces Service Bulletin 221-49, Piston Cooling, dated (1.2007), publication no. PV776-20177472. DService Bulletin Trucks Date Group
More information2007 Explorer/Mountaineer/Explorer Sport Trac Workshop Manual MERCON V
2007 Explorer SECTION 307-01A: Automatic Transaxle/Transmission 5R55S 2007 Explorer/Mountaineer/Explorer Sport Trac Workshop Manual Report a problem with this article IN-VEHICLE REPAIR Procedure revision
More informationAutomatic Transmission 5R44E and 5R55E
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Special Tool(s) Aligner, Valve Body 307-333 (T95L-70010-B) Aligner, Valve Body 307-334 (T95L-70010-C)
More informationPage 1 of 7 SECTION 303-04D: Fuel Charging and Controls Turbocharger 2006 F-Super Duty 250-550 Workshop Manual GENERAL PROCEDURES Procedure revision date: 10/09/2009 Turbocharger Reconditioning Printable
More informationM-5220-MSVT GT500 with Quad Side Exhaust INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Procedures» Removal Cylinder Heads http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=376&nonstandardid=682956&vehicleid=45317&windowname=maina
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Valve Cover» Service and Repair» Procedures» RH Valve Cover RH Removal 1. Disconnect the battery ground cable. 2. Remove the air cleaner
More informationOil Pan Replacement Buick Regal
2000 Buick Regal Oil Pan Replacement Removal Procedure Tools Required J 28467-90A Engine Support Adapters J 28467-B Universal Engine Support Fixture J 36462-A Engine Support Adapter Leg Set 1. Disconnect
More informationSECTION Automatic Transaxle/Transmission 6R80
307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE IN-VEHICLE REPAIR Main Control... 307-01-2 307-01-2 Automatic Transaxle/Transmission
More information2008 F-Super Duty Workshop Manual
Page 1 of 13 SECTION 303-04C: Fuel Charging and Controls 6.4L Diesel 2008 F-Super Duty 250-550 Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/04/2009 Fuel Injection Pump High Pressure,
More information1990 Buick Electra Limited
4. To install remaining components, reverse removal procedure. Coat rocker arm bolts with GM Threadlock (12345493) prior to installation. Fig. 3: Cylinder Head Bolt Tightening Sequence FRONT CRANKSHAFT
More information