SECTION Automatic Transaxle/Transmission 4R70E/4R75E
|
|
|
- Carmella Underwood
- 6 years ago
- Views:
Transcription
1 i Automatic Transaxle/Transmission 4R70E/4R75E i SECTION Automatic Transaxle/Transmission 4R70E/4R75E CONTENTS PAGE Transmission Four Wheel Drive (4WD)
2 Automatic Transaxle/Transmission 4R70E/4R75E Transmission Four Wheel Drive (4WD) Special Tool(s) Retainer, Torque Converter (T97T-7902-A) Removal 1. Disconnect the battery ground cable. For additional information, refer to Section Remove the transfer case. For additional information, refer to Section B. 3. NOTE: If transmission disassembly is required, drain the transmission fluid. Loosen the transmission fluid pan bolts and allow the transmission fluid to drain. 4. After the transmission fluid has drained, remove the transmission fluid pan and drain the remaining transmission fluid from the transmission fluid pan. Inspect the fluid pan for any visible debris (metal particles or clutch material). 5. If transmission fluid contamination or transmission failure is confirmed by debris in the bottom of the transmission fluid pan, the transmission fluid cooler bypass valve must be replaced. If the vehicle is equipped with an oil-to-air (OTA) cooler, a new OTA must be installed. 6. NOTE: It is not necessary to torque the transmission fluid pan bolts in this step. Install the transmission fluid pan.
3 Automatic Transaxle/Transmission 4R70E/4R75E Disconnect the selector lever cable end. 8. Disconnect the heated oxygen sensor (HO2S) connector. 9. Remove the HO2S connector from the selector lever cable bracket. 10. Remove the selector lever cable bracket from the transmission.
4 Automatic Transaxle/Transmission 4R70E/4R75E Remove the flexplate inspection cover. 12. Remove the rubber access plug. 13. Remove and discard the 4 flexplate-to-torque converter nuts. 14. Remove the plastic starter motor electrical connector cap.
5 Automatic Transaxle/Transmission 4R70E/4R75E Remove the starter motor electrical connectors and the ground wire. 16. Remove the 3 bolts and the starter motor. 17. Disconnect the transmission cooler tubes and position them aside. 18. Remove the bolt from the RH cylinder head for the transmission filler tube and position the filler tube aside.
6 Automatic Transaxle/Transmission 4R70E/4R75E Remove the 2 bolts for the exhaust hanger. 20. Remove the RH exhaust shield bolt. 21. Remove the LH exhaust shield bolt. 22. NOTE: Make sure that the transmission is securely fastened to a suitable transmission jack. Position a suitable high-lift transmission jack under the transmission. 23. Remove the insulator nuts.
7 Automatic Transaxle/Transmission 4R70E/4R75E Remove the rear transmission retainer bolts and remove the crossmember. 25. Remove the insulator bolts. 26. Disconnect the electrical connectors and remove the wire harness from the transmission. 1 Disconnect the digital transmission range (TR) sensor electrical connector. 2 Disconnect the output shaft speed (OSS) sensor electrical connector. 3 Disconnect the turbine shaft speed (TSS) sensor electrical connector. 27. Disconnect the solenoid body assembly electrical connector.
8 Automatic Transaxle/Transmission 4R70E/4R75E NOTE: Note the length and the location of the bolts during removal. Remove the 7 transmission-to-engine bolts. 29. WARNING: Secure the torque converter in the transmission during removal or installation. The torque converter is heavy and may result in injury if it falls out of the transmission. Failure to follow this instruction may result in serious personal injury. Leaving the transmission in a horizontal position, slide it back far enough to install the special tool. Install the special tool. 30. NOTICE: To remove the transmission from the vehicle, it will be necessary to put the transmission into a nose-down position to clear, and not damage, the flexplate and the exhaust system. NOTE: Make sure that the special tool is in place and the transmission is securely fastened to a suitable transmission jack before tilting the transmission. Lower the transmission from the vehicle.
9 Automatic Transaxle/Transmission 4R70E/4R75E Once the transmission is clear of the vehicle, the transmission fluid cooler and cooler tubes should be cleaned. Carry out transmission fluid cooler backflushing and cleaning. For additional information, refer to Transmission Fluid Cooler Backflushing and Cleaning in this section. 32. Remove the special tool. 33. Remove the vent tube.
2002 F-150 Workshop Manual
Page 1 of 8 SECTION 307-01B: Automatic Transmission 4R70W 2002 F-150 Workshop Manual REMOVAL Procedure revision date: 04/02/2003 Transmission Special Tool(s) Retainer, Torque Converter 307-346 (T97T-7902-A)
1999 Explorer/Mountaineer Workshop Manual
Page 1 of 5 SECTION 307-01B: Automatic Transmission 5R55E 1999 Explorer/Mountaineer Workshop Manual REMOVAL Procedure revision date: 07/27/1998 Transmission Special Tool(s) Torque Converter Holding Tool
Transmission Diesel Engines
Page 1 of 17 SECTION 307-01B: Automatic Transaxle/Transmission TorqShift 6 2011 F-250, 350, 450, 550 Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 11/12/2010 Transmission
1998 Ford EXPEDITION. Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS. Transmission
1998 Ford EXPEDITION Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS SECTION 307-01C: Automatic Transmission 4R100 1998 Expedition/Navigator Workshop Manual REMOVAL Procedure revision
IN-VEHICLE REPAIR. Output Shaft Speed (OSS) Sensor. Removal
307-01-1 Automatic Transaxle/Transmission 6F50 307-01-1 IN-VEHICLE REPAIR Output Shaft Speed (OSS) Sensor Material Item MERCON V Automatic Transmission Fluid XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada)
Transmission. All vehicles
INSTALLATION: TRANSMISSION (A... INSTALLATION: TRANSMISSION (AUTOMATIC TRANSAXLE/TRANSMISSION) 307 01 Automatic Transaxle/Transmission 2006 Mustang INSTALLATION Procedure revision date: 07/11/2008 All
3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter
1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower
Transmission. Special Tool(s) Installation. All vehicles
Transmission Special Tool(s) Installation All vehicles 1. CAUTION: Prior to the installation of the transmission, the fluid, cooler lines and the cooler bypass valve must be cleaned. Transmission failure
1 of 14 11/19/ :45 AM
1 of 14 11/19/2016 11:45 AM 6F35 Digital Transmission Range (TR) Sensor Removal All vehicles 1. With the vehicle in NEUTRAL, position it on a hoist. 3.0L engine 2. Remove the Air Cleaner (ACL) outlet pipe.
BD PERFORMANCE TRANSMISSION
1 BD PERFORMANCE TRANSMISSION 2008-10 F o r d 6. 4 L ( 5 R 1 1 0 ) I n s t a l l a t i o n I n s t r u c t i o n s 4WD Part # 1064494 2WD Part # 1064492 Please read the instructions and warranty disclaimer
IN-VEHICLE REPAIR. Main Control Valve Body. Removal. 6. Disconnect the transaxle wiring harness electrical connector and TR sensor connector.
307-01-1 Automatic Transaxle/Transmission 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Material Item Thread Sealant with PTFE TA-24 Motorcraft MERCON Multi-Purpose (ATF) Transmission Fluid XT-2-QDX
2004 F-150 Workshop Manual
Page 1 of 8 SECTION 303-01B: Engine 5.4L (3V) 2004 F-150 Workshop Manual REMOVAL Procedure revision date: 02/10/2004 Engine Printable View (943 KB) Special Tool(s) Modular Engine Lift Bracket 303-F047
BD PERFORMANCE TRANSMISSION
1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD PERFORMANCE TRANSMISSION 2008-10 F o r d 6. 4 L ( 5 R 1 1 0 ) I n s t a l l a t i o n I n s t r u c t i o n s 4WD Part # 1064494 2WD Part
DIAGNOSIS AND TESTING
307-01-1 Automatic Transaxle/Transmission 307-01-1 DIAGNOSIS AND TESTING Transmission Connector Layouts Connector Reference and Terminal Readings Powertrain Control module (PCM) 1 Pressure control solenoid
F o r d I n s t a l l a t i o n I n s t r u c t i o n s
1 DO NOT USE WATER-BASED TRANSMISSION FLUSHING FLUID THE LINING IN THE CONVERTOR CLUTCHES WILL DISINTIGRATE, RENDERING THE CONVERTOR USELESS AND WARRANTY WILL BE VOIDED. BD PERFORMANCE TRANSMISSION F o
DISASSEMBLY AND ASSEMBLY
307-01-1 Automatic Transaxle/Transmission 4R70E/4R75E 307-01-1 DISASSEMBLY AND ASSEMBLY Main Control Valve Body Disassembly Main Control Valve Body Disassembled View Item Part Number Description Item Part
Page 1 of 6 Section 07-01A: Transaxle, Automatic CD4E 1996 Probe Workshop Manual REMOVAL Procedure revision date: 06/14/2000 Transaxle Item Part Number Description 1 10655 Battery 2 10732 Battery Tray
2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI - Removal and Installation
Page 1 of 8 Removal and Installation REMOVAL 1. REMOVE HOOD Torque: 13 Nm (130 kgf-cm, 9 ft. lbs.) 2. REMOVE BATTERY 3. REMOVE ECM AND ECM CASE Torque: 6.9 Nm (70 kgf-cm, 61 inch lbs.) 4. REMOVE ECM BRACKET
REPLACEMENT. 9. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 (a) Remove the 2 bolts and control cable bracket No.1.
AUTOMATIC TRANSMISSION / TRANS REPLACEMENT 1. REMOVE HOOD SUBASSY 2. REMOVE BATTERY 3. REMOVE WINDSHIELD WIPER LINK ASSY (See page 666) 4. REMOVE FRONT PANEL ASSY (See page 2610) 5. REMOVE CYLINDER HEAD
SECTION Automatic Transaxle/Transmission 6R80
307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE IN-VEHICLE REPAIR Main Control... 307-01-2 307-01-2 Automatic Transaxle/Transmission
FULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L
2018-01-15 FORD F150 ECOBOOST 3.5L FULL BORE PERFORMANCE MANIFOLD SET (PART #500101X) 1 FULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L INSTALLATION INSTRUCTIONS 2011-2012 FORD F150 3.5L ECOBOOST
2001 Chevrolet CORVETTE
riveline Support Assembly Replacement (Automatic Transmission) 1 of 21 10/24/2012 8:58 PM 2001 Chevrolet CORVETTE Submodel: Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Driveline Support Assembly
Page 1 of 22 SECTION 307-01: Automatic Transaxle/Transmission 4R70E/4R75E ASSEMBLY Procedure revision date: 05/29/2009 Transmission Printable View (1554 KB) Special Tool(s) Air Test Plate, Transmission
1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
file://c:\program Files\tsocache\OFFICE_2780\SXN~us~en~file=SXNB2012.htm~gen~ref...
Page 1 of 14 SECTION 211-02: Power Steering 1999 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 07/27/1998 Gear 5.0L Removal 1. Place the front wheels in the straight
SECTION B Manual Transaxle/Transmission TR6060
308-03B-i Manual Transaxle/Transmission TR6060 308-03B-i SECTION 308-03B Manual Transaxle/Transmission TR6060 CONTENTS PAGE Transmission... 308-03B-2 308-03B-2 Manual Transaxle/Transmission TR6060 308-03B-2
REMOVAL AND INSTALLATION
303-03-1 Engine Cooling 303-03-1 REMOVAL AND INSTALLATION Radiator, Cooling Fan and Shroud Special Tool(s) Wrench, Fan Clutch Nut 303-240 (T84T-6312-D) Holding Wrench, Fan Pulley 303-239 (T84T-6312-C)
2003 Volkswagen Passat GL
2001-03 AUTOMATIC TRANSMISSIONS Removal & Installation - 01V APPLICATION TRANSAXLE APPLICATION Application Transaxle Model Passat 1.8L (FWD) 01V 2.8L (FWD & 4WD) 01V 4.0L (AWD) 2002-03 01V REMOVAL & INSTALLATION
1999 E-Series Workshop Manual
http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998
DISASSEMBLY AND ASSEMBLY
307-01-1 Automatic Transaxle/Transmission 307-01-1 DISASSEMBLY AND ASSEMBLY Transaxle Special Tool(s) Dial Indicator Gauge With Holding Fixture 100-002 (TOOL-4201-C) Special Tool(s) Test Plate Screw Set,
DISASSEMBLY. Transmission. All vehicles
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 DISASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Remover, Servo 307-347 (T97T-7D021-A)
DIAGNOSIS AND TESTING
307-01-1 Automatic Transmission 5R55S 307-01-1 DIAGNOSIS AND TESTING Transmission Connector Layouts Connector Reference and Terminal Readings Powertrain Control Module (PCM) C175b 1 Shift Solenoid A (SSA)
REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH. 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N.
REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N. (b) Check that the parking brake is released. (c) Remove
MAIN CONTROL VALVE BODY. Removal 1. Disconnect the battery cables. 2. Remove the battery and tray.
1 of 17 MAIN CONTROL VALVE BODY Removal 1. Disconnect the battery cables. 2. Remove the battery and tray. 3. Disconnect the breather tube and mass air flow (MAF) / intake air temperature (IAT) sensor.
Disconnect the breather tube and mass air flow (MAF) /intake air temperature (IAT) sensor.
1 of 19 10/1/2011 11:11 AM oval 1. 2. Disconnect the battery cables. Remove the battery and tray. 3. Disconnect the breather tube and mass air flow (MAF) /intake air temperature (IAT) sensor. 4. Remove
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual REMOVAL Procedure revision date: 07/25/2008 Engine Special Tool(s) Heavy Duty Floor Crane 014-00071 or equivalent Lifting Bracket, Engine
1998 Contour/Mystique Workshop Manual
SECTION 30-01: Automatic Transmission/Transaxle 1998 Contour/Mystique Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 09/14/2001 Main Controls Special Tool(s) Aligner, Selector Shaft 30-S290
10/13/2016 5:33 PM. Radiator (B205L/R, B235R) To remove
1 of 15 Radiator (B205L/R, B235R) To remove 1. Disconnect the vent hose from the battery. Disconnect the positive and negative battery cables and remove the battery. Note the radio code where applicable.
1 of 1 7/1/17, 2:02 PM. Air Cleaner Assembly Replacement ALLDATA, LLC. All Rights Reserved. (Version )
Air Cleaner Housing Service and Repair, Removal and Replacement: Ai... http://repair.alldata.com/alldata/article/display.action?componentid=367... 1 of 1 7/1/17, 2:02 PM Air Cleaner Assembly Replacement
PARTIAL ENGINE ASSY (2TR FE)
COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER
2002 F-Super Duty /Excursion Workshop Manual
Page 1 of 25 SECTION 307-01: Automatic Transaxle/Transmission 2002 F-Super Duty 250-550/Excursion Workshop Manual ASSEMBLY Procedure revision date: 05/23/2001 Transmission Special Tool(s) Remover, O-Ring
Items Vehicles with 4G63 engine Vehicles with 4D56 engine. Type 5-speed, floor-shift 5-speed, floor-shift. 2nd rd
22-2 MANUAL TRANSMISSION General Information GENERAL INFORMATION 22100010113 Items Vehicles with 4G63 engine Vehicles with 4D56 engine Transmission model R5M21-5 R5M21-5 Type 5-speed, floor-shift 5-speed,
Page 1 of 8 2012 Ford F450 Super Duty 6.7L Eng Service Manual: ENGINE MECHANICAL - 6.7L DIESEL -- F250-F550 SUPER DUTY IN-VEHICLE REPAIR > OIL PAN - LOWER MATERIAL SPECIFICATIONS Item Motorcraft SAE 0W-30
Intake Components 1117
Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold
Zoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
Page 1 of 7 Section 07-01A: Transmission, Automatic, E4OD IN-VEHICLE SERVICE 1993 Bronco/Econoline/F-Series Workshop Manual Valve Bodies and Intermediate Band Servo NOTE: If a transmission has been disassembled
CERTAIN 2018 MODEL YEAR EXPEDITION AND NAVIGATOR VEHICLES EQUIPPED WITH R-1234YF REFRIGERANT - SPECIAL R-1234YF REFRIGERANT SERVICE INFORMATION
PAGE 1 OF 33 CERTAIN 2018 MODEL YEAR EXPEDITION AND NAVIGATOR VEHICLES EQUIPPED WITH R-1234YF REFRIGERANT - SPECIAL R-1234YF REFRIGERANT SERVICE INFORMATION OVERVIEW This program provides special service
1994 Bronco/Econoline/F-Series
Page 1 of 8 Section 10-01A: Fuel Tank, Filters, Lines and Electric Fuel Pump, Gasoline Engines REMOVAL AND INSTALLATION 1994 Bronco/Econoline/F-Series Workshop Manual Fuel Tank Steel Midship Fuel Tank,
Page 1 of 14 Oil Pan Removal & Installation 4.2L Engine 4WD Vehicles To Remove: 1. Before servicing the vehicle refer to the precautions at the beginning of this section. 2. Raise and support the vehicle.
ASSEMBLY/INSTALLATION INSTRUCTIONS
ASSEMBLY/INSTALLATION INSTRUCTIONS AURORA 3000 & 4000 SCORPION TURBO SYSTEM NOTICE: The engine oil must be changed any time the turbocharger is removed from the engine. The passages in the block underneath
Catalytic Converter: Service and Repair
2007 GMC Truck Envoy 4WD V8-5.3L Copyright 2009, ALLDATA 10.10 Page 1 Catalytic Converter: Service and Repair Catalytic Converter Replacement (5.3L and 6.0L Engines) Removal Procedure 1. Raise and suitably
10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L
2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN
1 M-3000-H4 F150 4X4 Lowering Kit
READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. IT IS RECOMMENDED THAT INSTALLATION BE DONE BY A QUALIFIED MECHANIC. REPLACE ALL STOCK PARTS THAT ARE DAMAGED OR WORN. ALWAYS WEAR EYE PROTECTION.
Fastener Tightening Specifications Specification
2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt
2004 DRIVELINE/AXLE. Rear Drive Axle - Corvette. Fastener Tightening Specifications Specification Application
2004 DRIVELINE/AXLE Rear Drive Axle - Corvette SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Differential Case Bolts 55 N.m
2000 Ranger Workshop Manual
SECTION 211-02: Power Steering 2000 Ranger Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/1/1999 Gear Torsion Bar Suspension Special Tool(s) Remover, Tie Rod End 211-001 (TOOL-3290-D)
2006 F-150/Mark LT Workshop Manual
Page 1 of 14 SECTION 307-01: Automatic Transaxle/Transmission 4R70E/4R75E DIAGNOSIS AND TESTING Procedure revision date: 09/26/2008 Pinpoint Tests OSC Equipped Vehicle Printable View (485 KB) Special Tool(s)
1998 Escort/Tracer Workshop Manual
Page 1 of 11 SECTION 307-01: Automatic Transaxle/Transmission 1998 Escort/Tracer Workshop Manual DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIES Procedure revision date: 03/05/1998 Main Control Valve Body Assembly
Automatic Transmission 5R44E and 5R55E
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Special Tool(s) Aligner, Valve Body 307-333 (T95L-70010-B) Aligner, Valve Body 307-334 (T95L-70010-C)
SERVICE MANUAL Gearbox - Allison AT545 - Gearbox Installation
Gearbox - Allison AT545 - Gearbox Installation Oil level dipstick Gearbox oil cooler Auxiliary oil filter Modulator Page 3.4 Gearbox - Allison AT545 Checking Oil Level The dipstick and filler are situated
REMOVAL. 10. REMOVE FRONT SUSPENSION MEMBER BRACE Remove the 8 bolts and brace.
EM64 ENGINE MECHANICAL (2JZGE) EM1S801 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DRAIN ENGINE OIL 4. REMOVE ENGINE COVER Remove the 4 nuts and engine cover. 5. REMOVE AIR CLEANER
Zoom and Print Options
Vehicle» Powertrain Management» Fuel Delivery and Air Induction» Fuel Tank» Service and Repair» Procedures» Fuel Tank Removal and Installation REMOVAL WARNING: DO NOT SMOKE OR CARRY LIGHTED TOBACCO OR
CLEANING AUTOMATIC TRANSMISSION COMPONENTS
Classification: Reference: Date: AT87-008 TS87-172 November 23, 1987 CLEANING AUTOMATIC TRANSMISSION COMPONENTS APPLIED VEHICLE(S): All Nissan models equipped with automatic transmission or transaxle SERVICE
MANUAL TRANSMISSION CONTENTS
22-1 MANUAL TRANSMISSION CONTENTS GENERAL INFORMATION.................. 2 LUBRICANTS.............................. 2 SEALANT.................................. 2 SPECIAL TOOLS...........................
303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine
2010 MKZ Report a problem with this article 303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid REMOVAL Procedure revision date: 10/19/2012 Engine Special Tool(s) 2,200# Floor Crane,
Items Vehicles with 4G63 engine Vehicles with 4D56 engine. Type 4-speed full automatic 4-speed full automatic. 2nd rd
23-2 AUTOMATIC TRANSMISSION General Information/ Service Specifications GENERAL INFORMATION 23100010141 Items Vehicles with 4G63 engine Vehicles with 4D56 engine Transmission model R4AW2-6 V4AW2-6 Type
B&M / INTRODUCTION
INSTALLATION INSTRUCTIONS FOR B&M AUTOMATIC TRANSMISSIONS REPLACING GM TH350, TH400, and TH700R4 / 4L60 (not including 4L60E / electronic shift models) B&M part numbers: 102002-103005 - 107101-107104 107105-107106
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY Removal and Installation REMOVAL WARNING: Follow the "General Precautions" before working on the fuel system. Refer to "General Precautions".
Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly
Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie
2013 Mustang Workshop Manual
32. Attach the wiring harness retainers to the LH side of the oil pan and the front oil pan stud bolts and install the 2 nuts. Tighten to 8 Nm (71 lb-in). 33. Position the underbody shield and install
IN-VEHICLE REPAIR. Oil Pan Lower. Removal. 2. Disconnect the LH and RH battery ground cables. For additional information, refer to Section
303-01C-1 IN-VEHICLE REPAIR Oil Pan Lower Special Tool(s) 3-Bar Engine Support 303-F070 Lifting Eyes 303-D030 303-01C-1 2. Disconnect the LH and RH battery ground cables. For additional information, refer
Oil Pan Replacement Buick Regal
2000 Buick Regal Oil Pan Replacement Removal Procedure Tools Required J 28467-90A Engine Support Adapters J 28467-B Universal Engine Support Fixture J 36462-A Engine Support Adapter Leg Set 1. Disconnect
V6 Spring Belt Tensioner
Dodgerunner s V6 Spring Belt Tensioner Installation Guide Dodgerunner 2007 The bracket consists of two pieces of 1/8" steel bolted together. The main piece is flat plate with welded-on alternator mounting
Page 1 of 5 303-01B Engine 3.0L (4V) 2004 Escape IN-VEHICLE REPAIR Procedure revision date: 05/26/2005 Engine Front Cover Material Removal Item Motocraft Metal Surface Cleaner ZC-21 Silicone Gasket and
FUEL PUMP CAMSHAFT TIMING CHECK
PUBLISHED: 26-FEB-2018 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING CHECK (G1473740) GENERAL PROCEDURES 19.90.16 HIGH PRESSURE FUEL TIMING CHECK 5000 CC,
Fuel Tank: Service and Repair Fuel Tank Removal/Installation FUEL TANK REMOVAL/INSTALLATION
2004 Mazda 3 L4-2.3L Copyright 2013, ALLDATA 10.52 Page 1 Fuel Tank: Service and Repair Fuel Tank Removal/Installation FUEL TANK REMOVAL/INSTALLATION WARNING: Repairing a fuel tank containing fuel is dangerous.
Chevrolet Ford Dodge LCT1000--LCT RH / 47RE / 48RE E4OD / 4R100. Transmission removal, Installation And testing
ATS Transmission Procedures Chevrolet Ford Dodge LCT1000--LCT2500 47RH / 47RE / 48RE E4OD / 4R100 Transmission removal, Installation And testing Please read before any work is done Removal NOTE: NOTE:
2002 Explorer Sport/Sport Trac Workshop Manual
Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)
Removing the engine. General. Tools. Work description. Preparatory work
General General Applies to 9 and 13 litre engines with XPI, PDE or GAS and cylinder block generation 2. Tools Examples of suitable tools from Scania: Part number Designation 98 094 Lifting chain 99 318
Valve Body: Service and Repair
2007 Chevy Truck TrailBlazer 2WD L6-4.2L Copyright 2013, ALLDATA 10.52SS Page 1 Valve Body: Service and Repair Valve Body and Pressure Switch Replacement Removal Procedure 1. Ensure that removal of the
POWERSHIFT TRANSMISSION
1. Specifications... 5-3 2. Structure... 5-4 2.1 Torque converter... 5-4 2.2 Transmission... 5-5 2.3 Power Train Line... 5-6 2.4 Control Valve... 5-7 2.5 Main Regulator Valve... 5-7 2.6 Torque Converter
1. Remove the battery tray. For additional information, refer to Battery Tray ( )
Page 1 of 11 Removal 1. Remove the battery tray. For additional information, refer to Battery Tray (86.15.11) 2. Remove the air cleaner. For additional information, refer to Air Cleaner (19.10.05) 3. NOTE
9/20/2017 Automatic Transaxle/Transmission External Controls - Selector Lever Cable - Removal and Installation 2008 Ford Edge MotoLogic
2008 Edge SECTION 307-05: Automatic Transaxle/Transmission External Controls REMOVAL AND INSTALLATION 2008 Edge/MKX Workshop Manual Procedure revision date: 06/17/2009 Report a problem with this article
Assembly. NOTE: Before beginning assembly, perform/inspect the following:
Page 1 of 31 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 1997 Ford Truck F 150 2WD Pickup V6-4.2L VIN 2
Property of American Airlines
Maintenance / On Vehicle Service 4L6XE/70E 2013 PAGE 145 This manual provides Maintenance and some On-Vehicle Service Information for the 4L6XE/70E series transmission. For diagnostic information, refer
INSTRUCTIONS. Disassembly. Shifter Cam Assembly. Shifter Forks
INSTRUCTIONS Disassembly To protect against accidental start-up of vehicle, always disconnect the negative battery cable before working on the motorcycle. Failure to disconnect the battery cable could
Property of American Airlines
Operation and Maintenance Manual Appendix C, GM 4L6XE/4L70E Service This manual provides Maintenance and some On-Vehicle Service Information for the 4L6XE/70E series transmission. For diagnostic information,
5. Engine Control Module (ECM) I/O Signal
5. A: ELECTRICAL SPECIFICATION B134 B135 B136 B137 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 19 18 34 33 32 31 30 29 28 19 18 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 35 34 33 32 31
DIAGNOSIS AND TESTING
307-01-1 Automatic Transaxle/Transmission 307-01-1 DIAGNOSIS AND TESTING Pinpoint Tests OSC Equipped Vehicle Special Tool(s) Transmission Fluid Pressure Gauge 307-004 (T57L-77820-A) Special Tool(s) MLP-TR
Transmission, removing and
Page 1 of 20 34-18 Transmission, removing and installing Removing Special tools and equipment 3282 transmission support 3282/10 adjustment plate 3337 ring spanner 7-piece set VAG1383A engine/transmission
COMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
Removal. All vehicles. Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair. Special Tool(s) Check Pin - Camshaft Pulleys
Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair Special Tool(s) Check Pin - Camshaft Pulleys 303-1132 Timing Pin - Camshaft Pulleys 303-1126 Timing Pin - Automatic Transmission
AUTO TRANS OVERHAUL - V.A.G. 01V Article Text 1998 Volkswagen Passat This file passed thru Volkswagen Technical Site -
AUTO TRANS OVERHAUL - V.A.G. 01V Article Text 1998 Volkswagen Passat This file passed thru Volkswagen Technical Site - http://volkswagen.msk.ru ARTICLE BEGINNING 1997-98 AUTOMATIC TRANSMISSIONS Volkswagen/Audi
7-0 ENGINE REMOVAL 7. ENGINE REMOVAL/INSTALLATION MXU 500
7 ENGINE REMOVAL SERVICE INFORMATION------------------------------------------------ 7-1 ENGINE REMOVAL ------------------------------------------------------- 7-2 ENGINE INSTALLATION ------------------------------------------------
OVERVIEW: KIT INCLUDES:
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS Please visit www. performanceparts.ford.com for the most current instruction and warranty
Page 1 of 8 Section 03-01: Engine, 4.6L IN-VEHICLE SERVICE 1994 Town Car/Crown Victoria/Grand Marquis Workshop Manual Oil Pan and Oil Pump Screen Cover and Tube Town Car Removal 1. Disconnect battery ground
2001 Ranger Workshop Manual. 1. Drain the cooling system. For additional information, refer to Section
Exhaust Gas Recirculation (EGR) Valve 2.3L 1. Drain the cooling system. For additional information, refer to Section 303-03. 2. Disconnect the battery ground cable. For additional information, refer to
FUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G )
PUBLISHED: 10-OCT-2017 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G1473741) GENERAL PROCEDURES 19.90.17 HIGH PRESSURE FUEL TIMING CHECK AND
2003 F-Super Duty /Excursion Workshop Manual
Page 1 of 16 SECTION 303-01C: Engine 7.3L Diesel DISASSEMBLY Procedure revision date: 05/21/2002 Engine Printable View (1761 KB) Special Tool(s) Cylinder Head Lifting Tool (D94T-6000-B) 303-D098 Damper