M-5220-MSVT GT500 with Quad Side Exhaust INSTALLATION INSTRUCTIONS
|
|
- Robyn Ryan
- 6 years ago
- Views:
Transcription
1 Please visit for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE INSTRUCTIONS, PLEASE CALL THE FORD PERFORMANCE TECHLINE AT !!! OVERVIEW: THE USE OF A FLOOR HOIST IS RECOMMENDED FOR THIS INSTALLATION. IF YOU DO NOT HAVE ACCESS TO ONE, USE A HYDRAULIC FLOOR JACK AND JACK STANDS TO RAISE THE VEHICLE.!!! CAUTION: JACK STANDS MUST BE USED ON A LEVEL SURFACE AND BE SECURELY SEATED. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY OR VEHICLE DAMAGE!!! KIT INCLUDES: Item # Qty: Description CM-5426-WGT500 1 H-Pipe CR AG RH 1 Side exhaust pipe CR BG LH 1 Side exhaust pipe CR3Z-5B266-A 2 Gasket, H-pipe to side pipe W S900 4 Nut, H-pipe to side ex. pipe W S439 4 Bolt, H-pipe to side ex. pipe X 1 Heat Shroud : STEP 1: Raise and support vehicle. Techline Page 1 of 9 IS
2 STEP 2: Spray penetrate on Exhaust coupler bolts. Loosen all Exhaust coupler bolts. (Number 7 in figure below.) 5.8L Techline Page 2 of 9 IS
3 Fig. 3 Fig. 4 STEP 3: Lift clamp tabs (See Fig. 3). STEP 4: Slide both clamps toward rear of vehicle (See Fig. 4). Fig. 5 Fig. 6 STEP 5: Hold up new H-pipe and align with rear of exhaust (See Fig. #5). Mark H-pipe end with tape (See Fig. #6). Techline Page 3 of 9 IS
4 Fig. 7 Fig. 8 Fig. 9 STEP 6: Measure 1-1/2 from end of H-pipe tape mark and make tape cut line (See Fig. 7). STEP 7: Cut both pipes at cut line (See Fig. 8). STEP 8: Clean sharp edges and burrs with a file (See Fig. 9). Fig. 11 Fig. 12 Fig. 13 STEP 9: Slide new clamps on exhaust small end first (See Fig. 11, 12 & 13). STEP 10: Install new H-pipe in place (See Fig. 12 & 13). STEP 11: Slide new clamps over front connection and the original rear clamps over pipe (See Fig. 12 & 13). STEP 12: STEP 13: Tighten rear clamp bolts 54 Nm (40 lb-ft). Tighten front clamp bolts 54 Nm (40 lb-ft). Remove LH and RH plastic shields in front of fuel tank from the underside of the vehicle. Techline Page 4 of 9 IS
5 STEP 14: Add heat shroud tape to rear axle cooler lines, if vehicle is equipped (passenger side in front of rear tire). (See Fig. 14, 15 & 16) NOTE: If necessary adjust rear axle cooler line bracket to clear side exhaust. Fig. 14 Fig. 15 Fig. 16 Step 15: Assure proper clearance between rear axle cooler lines and side exhaust. (See Fig. 17) Fig. 17 Techline Page 5 of 9 IS
6 Side Pipe Installation: STEP 16: NOTICE: Do not bend, twist or allow the exhaust side pipes to hang from the flexible bellows or damage to the exhaust side pipe may occur. Tighten the LH and RH exhaust side pipe bolts. (#2 and #21) Insure that the LH and RH exhaust side pipe grommet assemblies are installed (#1 and #20) Tighten to 25 Nm (18 lb-ft). STEP 17: NOTE: Install gaskets in the correct position (See exploded view). NOTE: When tightening the side pipe-to-exhaust H-pipe nuts, rotate the side pipe assembly so the pipe after the Torca clamp has a clearance of 10 mm (0.393 in) to 19 mm (0.748 in) to the flat surface of the floor pan. Install gaskets, nuts and the LH and RH exhaust side pipes. Align the exhaust side pipes and tighten the exhaust side pipe-to-exhaust H-pipe nuts to 40 Nm (30 lb-ft). STEP 18: NOTE: When tightening the Torca clamp, make sure the flat section of the side pipes has a clearance of 14 mm (0.551 in) to 23 mm (0.905 in) to the floor pan. Tighten the exhaust side pipe Torca clamps. Tighten to 48 Nm (35 lb-ft). Techline Page 6 of 9 IS
7 Side Exhaust Kit Techline Page 7 of 9 IS
8 Item Description 1 LH exhaust side pipe grommet assembly 2 LH exhaust side pipe bolt - 25 Nm (18 lb-ft) 3 LH exhaust side pipe 4 LH exhaust side pipe Torca clamp - 48 Nm (35 lb-ft) 5 LH exhaust side pipe-to-exhaust H-pipe nut (2 required) - 40 Nm (30 lb-ft) 6 LH exhaust side pipe flange 10 Gasket 11 Exhaust H-Pipe 12 Gasket 16 RH exhaust side pipe-to-exhaust H-pipe nut (2 required) - 40 Nm (30 lb-ft) 17 RH exhaust side pipe flange 18 RH exhaust side pipe Torca clamp - 48 Nm (35 lb-ft) 19 RH exhaust side pipe 20 RH exhaust side pipe grommet assembly 21 RH exhaust side pipe bolt - 25 Nm (18 lb-ft) Techline Page 8 of 9 IS
9 Completed Installation of the GT500 Quad Exhaust System Techline Page 9 of 9 IS
M-5220-MB Mustang GT Side Exhaust Kit INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information.!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationM-5220-M L Quad Pipe Exhaust System INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationM-5230-V6 Mustang V6 Dual Exhaust Kit INSTRUCTION SHEET
Please visit www.fordracingparts.com for the most current instruction information.!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationOVERVIEW: KIT INCLUDES:
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS Please visit www. performanceparts.ford.com for the most current instruction and warranty
More informationM-5230-V6 Mustang V6 Dual Exhaust Kit INSTRUCTION SHEET
Please contact the Techline for the most current instruction information (800) FORD788.!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: The use of a floor hoist is
More informationOVERVIEW: KIT INCLUDES:
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationM-5230-MGTCA Mustang GT, Mustang GT500 INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationM-5230-MSVTCD Mustang GT with GT500 Quad Tip Exhaust INSTALLATION INSTRUCTIONS
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS. Please visit www.fordracingparts.com for the most current instruction information!!!
More informationOVERVIEW: KIT INCLUDES:
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationExhaust System Installation for the Ford Mustang PN s , , , , , , , ,
Exhaust System Installation for the PN s-140583, 140584,1 40585, 140586, 140587, 140588, 140589, 140590, 140591 ***** Please compare the parts in the box with the bill of materials provided ***** to assure
More informationREMOVAL AND INSTALLATION
303-03-1 Engine Cooling 303-03-1 REMOVAL AND INSTALLATION Radiator, Cooling Fan and Shroud Special Tool(s) Wrench, Fan Clutch Nut 303-240 (T84T-6312-D) Holding Wrench, Fan Pulley 303-239 (T84T-6312-C)
More informationTo ensure this part number fits your specific model year, please visit our website for the latest model year listings at
Exhaust System Installation for Ford Mustang GT, Shelby GT500, & Mustang V6 PN s 11789, 11790, 11791, 11792, 11793, 11796, 11797, 11798, 11799, 11836, 11837, & 11838 ***** Please compare the parts in the
More informationExhaust System Installation for the Ford Mustang PN s , , , , , , , ,
Exhaust System Installation for the Ford Mustang PN s-140583, 140584,1 40585, 140586, 140587, 140588, 140589, 140590, 140591 Precision manufactured using aircraft quality T-304 stainless steel; this system
More informationPlease compare the parts in the box with the bill of materials provided to assure that you have all the parts necessary for this installation.
Exhaust System Installation for Ford Mustang GT, Shelby GT500, & Mustang V6 PN s 11789, 11790, 11791, 11792, 11793, 11796, 11797, 11798, 11799, 11836, 11837, & 11838 These instructions have been written
More informationExhaust System Installation for the Mustang GT & Shelby GT500 PN , , , , ,
Exhaust System Installation for the Mustang GT & Shelby GT500 PN 140370, 140371, 140372, 140410, 140411, 140412 These instructions have been written to help you with the installation of your Borla Performance
More informationInstallation for Chevrolet Malibu 2.0L Turbo PN-11936
Installation for Chevrolet Malibu 2.0L Turbo PN-11936 BORLA PERFORMANCE INDUSTRIES ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts
More information1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions
Please visit www.performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT
More informationExhaust System Installation for the Ford Mustang PN s ,140584,140585,140589,140590,140591
Exhaust System Installation for the Ford Mustang PN s-140583,140584,140585,140589,140590,140591 Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years
More informationExhaust System Installation PN , , , , &
Exhaust System Installation PN-140415, 140416, 140417, 140438, & 140466 BORLA PERFORMANCE INDUSTRIES These instructions have been written to help you with the installation of your Borla Performance Exhaust
More informationOVERVIEW: KIT INCLUDES: Two piece drive shaft loop
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationInstallation for the Ford Mustang V-6 PN s , ,
Installation for the Ford Mustang V-6 PN s-140586, 140587, 140588 These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read this document
More informationExhaust System Installation for Nissan GT-R PN 12658
Exhaust System Installation for Nissan GT-R PN 12658 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts necessary for this installation.
More informationM-9603-FST FOCUS ST COLD AIR INTAKE KIT INSTALLATION INSTRUCTIONS
M-9603-FST Please visit www.fordracingparts.com for the most current instruction information.!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND
More informationM-5230-MSVTCD Mustang GT with GT500 Quad Tip Exhaust INSTALLATION INSTRUCTIONS
NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS.!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!!
More information2002 F-150 Workshop Manual
Page 1 of 8 SECTION 307-01B: Automatic Transmission 4R70W 2002 F-150 Workshop Manual REMOVAL Procedure revision date: 04/02/2003 Transmission Special Tool(s) Retainer, Torque Converter 307-346 (T97T-7902-A)
More informationInstallation Instructions for Challenger R/T: , , , Charger R/T: , , ,
Installation Instructions for Challenger R/T: 140713, 140714, 140715, 140716 Charger R/T: 140722, 140723, 140724, 140725 ***** Please compare the parts in the box with the bill of materials provided *****
More informationInstallation for Ford Explorer PN s , ,
Installation for Ford Explorer PN s- 140656, 140659, 140658 These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read this document completely
More informationCROWN VICTORIA POLICE INTERCEPTOR (CVPI) PACKAGE OPTIONAL UPGRADE KIT
PAGE 1 OF 6 AFFECTED S: OVERVIEW CROWN VICTORIA POLICE INTERCEPTOR (CVPI) PACKAGE OPTIONAL UPGRADE KIT CERTAIN 1992 THROUGH 2003 MODEL YEAR CROWN VICTORIA POLICE INTERCEPTOR (CVPI) S CURRENTLY IN POLICE
More information2013 Mustang Workshop Manual
32. Attach the wiring harness retainers to the LH side of the oil pan and the front oil pan stud bolts and install the 2 nuts. Tighten to 8 Nm (71 lb-in). 33. Position the underbody shield and install
More informationInstallation for Dodge Challenger R/T PN s ,
Installation for PN s-140707, 140708 ***** Please compare the parts in the box with the bill of materials provided ***** (view the following pages) to assure that you have all the parts necessary for this
More informationM-9424-M50CJ INTAKE MANIFOLD INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationExhaust System Installation For Dodge Challenger 3.5L
Exhaust System Installation For Dodge Challenger 3.5L BORLA PERFORMANCE INDUSTRIES These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please
More informationExhaust System Installation for Corvette, C6 or Z06 PN s , 11811, 11812, 11814, 11815, 11816, 11917
Exhaust System Installation for Corvette, C6 or Z06 PN s - 11810, 11811, 11812, 11814, 11815, 11816, 11917 ***** Please compare the parts in the box with the bill of materials provided ***** to assure
More informationIMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Performance We ask that you take a few moments to
More informationENGINE REMOVAL & INSTALLATION
TORQUE VALUES ENGINE MOUNTING = Apply Victory All Purpose Grease 2872187 1. Install all bolts in order A-H Do not tighten. E 41 Nm (30 lb-ft) M8 x 25mm D 111 Nm (82 lb-ft) 12 x 100mm ENGINE INSTALLATION
More information2000 Toyota Celica GT-S L4-1762cc 1.8L DOHC MFI - Removal and Installation
Page 1 of 8 Removal and Installation REMOVAL 1. REMOVE HOOD Torque: 13 Nm (130 kgf-cm, 9 ft. lbs.) 2. REMOVE BATTERY 3. REMOVE ECM AND ECM CASE Torque: 6.9 Nm (70 kgf-cm, 61 inch lbs.) 4. REMOVE ECM BRACKET
More informationM-2300-T 6-Piston Mustang Brake Kit INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationM-FR3-FA Fiesta Handling Pack INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationPowerstroke EGR Delete A B C
20-203 6.7 Powerstroke EGR Delete A B C D E F G H I J K Part # A B C D E F G H I J K PACKING LIST: QTY. 3 5 2 Description Sensor Bracket Exhaust Blockoff Plate Straights Barbed Brass Fitting 39 5/8 Coolant
More informationChevrolet Camaro Exhaust System Installation PN s , , , , , , , , , , ,
Chevrolet Camaro Exhaust System Installation PN s -140280, 140281, 140282, 140348, 140356, 140493, 140494, 140495, 140526, 140530, 140528, 140532 Thank you for purchasing a Borla Performance Cat-Back Exhaust
More informationRear Toyota Landcruiser 4x4 S-W GX 91 Onwards
60728A0 Rear Toyota Landcruiser 4x4 S-W 80-100 GX 91 Onwards LOWER SPRING SEAT.DRILLING INSTRUCTIONS 6. The picture above shows the expected result after drilling the hole in step 4. 1. The spring seat
More informationInstallation for Dodge Charger R/T PN s , ,
Installation for Dodge Charger R/T PN s 140635, 140636, 140637 These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read this document
More informationIMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Exhaust We ask that you take a few moments to complete
More informationIMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Exhaust We ask that you take a few moments to complete
More informationLong Tube Header Installation for Charger R/T, Magnum R/T, Chrysler 300C, Challenger R/T & Charger R/T PN *,17256*, 17275*
Long Tube Header Installation for Charger R/T, Magnum R/T, Chrysler 300C, Challenger R/T & Charger R/T PN - 17252*,17256*, 17275* ***** Please compare the parts in the box with the bill of materials provided
More informationSTOP IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED TO ACTIVATE YOUR LIMITED LIFETIME WARRANTY GO TO: CORSAPERFORMANCE.
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Exhaust We ask that you take a few moments to complete
More informationHeader Installation For Jeep Wrangler
Header Installation For 2007-2008 Jeep Wrangler Precision manufactured using high quality austenitic stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance
More informationInstallation for Ford F-150 Raptor (V6 Ecoboost) PN s , 60638, 60650*
Installation for (V6 Ecoboost) PN s- 60637, 60638, 60650* ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts necessary for this installation.
More informationExhaust System Installation for Chevrolet Corvette C6 PN and
Exhaust System Installation for Chevrolet Corvette C6 PN-140128 and 140131 These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read this
More informationExhaust System Installation for Chevrolet Silverado and GMC Sierra PN , , , , ,
Exhaust System Installation for Chevrolet Silverado and GMC Sierra PN-140535, 140536, 140537, 140538, 140539, 140540 ***** Please compare the parts in the box with the bill of materials provided *****
More informationOwner smanual. Banks TorqueTube System Ford 5.4L F-150 (Late Body Style) with Installation Instructions
Owner smanual with Installation Instructions Banks TorqueTube System 2004-2008 Ford 5.4L F-150 (Late Body Style) THIS MANUAL IS FOR USE WITH SYSTEMS 48715 Gale Banks Engineering 546 Duggan Avenue Azusa,
More informationInstallation for Jeep Grand Cherokee SRT8 PN s , and 60634, 60635
Installation for Jeep Grand Cherokee SRT8 PN s-140632, 140633 and 60634, 60635 BORLA PERFORMANCE INDUSTRIES ***** Please compare the parts in the box with the bill of materials provided ***** to assure
More informationExhaust System Installation for the Ford F-150 PNs , , , , , ,
Exhaust System Installation for the Ford F-150 PNs 140693, 140694, 140695, 140696 140697, 140698, 140699, 140700 BORLA PERFORMANCE INDUSTRIES ***** Please compare the parts in the box with the bill of
More information1994 Bronco/Econoline/F-Series
Page 1 of 8 Section 10-01A: Fuel Tank, Filters, Lines and Electric Fuel Pump, Gasoline Engines REMOVAL AND INSTALLATION 1994 Bronco/Econoline/F-Series Workshop Manual Fuel Tank Steel Midship Fuel Tank,
More informationPlease compare the parts in the box with the bill of materials provided to assure that you have all the parts necessary for this installation.
Installation for Chevrolet Corvette C7 Stingray & ZO6 (Standard exhaust) PN s - 11862, 11863, 11868, 11869, 11877, 11878, 11880, 11881 (Optional NPP) PN s - 11874, 11855, 11875, 11856 ZO6 PN s - 11902,
More informationInstallation for Chevrolet Silverado & GMC Sierra PN s , , ,
Installation for Chevrolet Silverado & GMC Sierra PN s-140717, 140718, 140719, 140720 BORLA PERFORMANCE INDUSTRIES ***** Please compare the parts in the box with the bill of materials provided ***** to
More informationFord Mustang GT Long Tube Header Installation
2005-2006 Ford Mustang GT Long Tube Header Installation Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance
More informationM H Harley/F150 Vacuum Boost Gauge INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationIN-VEHICLE REPAIR. Oil Pan Lower. Removal. 2. Disconnect the LH and RH battery ground cables. For additional information, refer to Section
303-01C-1 IN-VEHICLE REPAIR Oil Pan Lower Special Tool(s) 3-Bar Engine Support 303-F070 Lifting Eyes 303-D030 303-01C-1 2. Disconnect the LH and RH battery ground cables. For additional information, refer
More informationA-Spec Racing EK-RBS-01. Section I Installation Preparations. Sub Frame Reinforcement Brace. Rev: B ASR General Applicability
Part number: EK-RB-01 EK-RBS-01 Section I Installation Preparations General Applicability 1996-2000 Civic Hatch Back DX, CX 1996-2000 Civic Coupe EX, HX, DX 1996-2000 Civic Sedan EX, VP, LX, DX 1999-2000
More informationOwner smanual. Banks Monster Exhaust System Toyota FJ Cruiser. with Installation Instructions
with Installation Instructions Owner smanual Banks Monster Exhaust System 2007-2009 Toyota FJ Cruiser THIS MANUAL IS FOR USE WITH MONSTER EXHAUST SYSTEMS 48141, 48142 Gale Banks Engineering 546 Duggan
More informationPlease take time to read and understand these installation instructions.
Cat Back Exhaust System 2013+ SRT/ GTS Viper Please take time to read and understand these installation instructions. CORSA recommends that the installation of this system be performed by a qualified service
More informationInstallation for Dodge Challenger & Charger HellCat PN s , , , , , , ,
Installation for PN s-140642, 140646, 140647, 140648, 140666, 140667, 140668, 140669 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the
More informationLong Tube Header Installation For Dodge Challenger SRT-8 & R/T, Charger SRT-8 & R/T, Magnum SRT-8 & R/T & Chrysler 300 SRT-8 & 300C
Long Tube Header Installation For 2005-2008 Dodge Challenger SRT-8 & R/T, Charger SRT-8 & R/T, Magnum SRT-8 & R/T & Chrysler 300 SRT-8 & 300C Precision manufactured using high quality austenitic stainless
More informationLong Tube Header Installation For Ford Mustang GT
Long Tube Header Installation For 2005-2008 Ford Mustang GT Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla
More informationM-6010-R451/R452 Ford Racing 351 Race Block INSTRUCTION SHEET
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationPiston Cooling Nozzle, Replacement
Volvo Trucks North America Greensboro, NC USA This Service Bulletin replaces Service Bulletin 221-49, Piston Cooling, dated (1.2007), publication no. PV776-20177472. DService Bulletin Trucks Date Group
More informationSECTION C Engine 5.4L (4V)
303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE IN-VEHICLE REPAIR Timing Drive Components... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 IN-VEHICLE REPAIR Timing
More informationROUSH Cat Back Exhaust
ROUSH Cat Back Exhaust Installation Instructions 2015-2018 2.3L I-4 P/N: 422094 (1315-5G203) 2015-2017 5.0L V8 P/N: 422092 (1315-5G201) 2018 5.0L V8 P/N: 422093 (1318-5G202) 39555 Schoolcraft Rd, Plymouth
More information1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST MUSTANG LONG TUBE HEADERS (M30000)
2/18/04 1501 Industrial Way N., Toms River, NJ 08755 732-349-2109 Fax:732-244-0867 ADVANCED - Installation requires professional-type tools and advanced automotive-service skills. If you lack experience
More informationINSTRUCTION, HALDEX PUMP LVS KIT P/N
LIFT CORPORATION Sht. 1 of 11 DSG# M-06-33 Rev. - Date: 12/17/07 INSTRUCTION, HALDEX PUMP LVS KIT P/N 267923-01 MALE BULLET LVS WIRE HARNESS P/N 267924-01 QTY. 1 LOW VOLTAGE SWITCH (LVS MODULE) P/N 906530-01
More informationChevrolet Camaro (Gen6) Installation Guide PN 11920, 11921, 11924, 11925, 11926, 11927, 11930, 11931
Installation Guide PN 11920, 11921, 11924, 11925, 11926, 11927, 11930, 11931 ***** Please compare the parts in the box with the bill of materials provided ***** (view the following pages) to assure that
More informationMODEL NO & UP
FORM NO. 97 50xi GARDEN TRACTOR MODEL NO. 7570 990000 & UP SET UP INSTRUCTIONS Loose Parts Use the chart below to identify parts for assembly. DESCRIPTION QTY. USE Rear Wheel Wheel Bolt R.H. Wheel Spindle
More informationM-9603-M50CJ COLD AIR INTAKE INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More information2007 Ford Freestyle SEL
Fig. 279: Exploded View Of Engine Heads, Intake & Exhaust Components Item Part Number Description 1 9D475 Exhaust gas recirculation (EGR) system module 2 9D477 EGR module tube 3 9F485 RH exhaust manifold
More informationOwner s Manual. Banks Ram-Air Intake System Ford 6.8L V-10, 30-valve Class-A Motorhome. with Installation Instructions
with Installation Instructions Owner s Manual Banks Ram-Air Intake System 06-08 Ford 6.8L V-10, 30-valve Class-A Motorhome THIS MANUAL IS FOR USE WITH KIT 49191 Gale Banks Engineering 546 Duggan Avenue
More informationExhaust System Installation for Audi S5, S4, and S6 PNs , ,
Exhaust System Installation for Audi S5, S4, and S6 PNs-140391, 140403, 140704 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts
More informationFord 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.
1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T
More information3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter
1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower
More informationTOYOTA CAMRY SE V SPORT EXHAUST. Conflicts. Part Number: Code: DE1. Kit Contents. Hardware Bag Contents.
TOYOTA CAMRY SE V6 2014 SPORT EXHAUST Part Number: 00016-32021 Code: DE1 Conflicts Note: Kit Contents Item # Qty. Reqd. Description 1 1 L/H Muffler Assembly 2 1 R/H Muffler Assembly 3 4 5 6 7 8 Hardware
More informationFULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L
2018-01-15 FORD F150 ECOBOOST 3.5L FULL BORE PERFORMANCE MANIFOLD SET (PART #500101X) 1 FULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L INSTALLATION INSTRUCTIONS 2011-2012 FORD F150 3.5L ECOBOOST
More information15-17 FORD MUSTANG GT
15-17 FORD MUSTANG GT IMPORTANT! WARRANTY AND Please Forward All Information to Consumer Be sure to review the enclosed instructions prior to beginning the installation process. If you have any questions
More informationC7 Corvette Blackheart 3 304SS Cat-Back Exhaust System w/ AFM Valves RHKR w/ NPP Mufflers
2014-2015 C7 Corvette Blackheart 3 304SS Cat-Back Exhaust System w/ AFM Valves 70501349-RHKR w/ NPP Mufflers Installation Instructions Thank you for making HOOKER HEADERS your choice in a high-performance
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 2102 LOWERING SPINDLE ASSEMBLY 1998-UP CHEVROLET / GMC BLAZER / X-TREME / JIMMY / ENVOY 2 Wheel Drive Congratulations! You were selective enough to choose a BELLTECH PRODUCT.
More informationService Bulletin No. 3033
MODEL TYPE SECTION/GROUP DATE G Series Coaches Product Improvement 2--Rear Axle Mar. 31, 2010 SUBJECT CONDITIONS BEARING BOX Parts may be purchased from MCI Service Parts, Louisville, Kentucky or from
More informationBanks Monster Exhaust Rear Quads System
Banks Monster Exhaust Rear Quads System 2007-2008 Chevy/GMC 1500 Silverado, 6.0L V-8 Gas, Vortex Max THIS MANUAL IS FOR USE WITH MONSTER EXHAUST SYSTEMS 48347 Gale Banks Engineering 546 Duggan Avenue Azusa,
More informationExhaust System Installation for Subaru Impreza WRX + STI PNs ,140381,140418, &
Exhaust System Installation for Subaru Impreza WRX + STI PNs-140264,140381,140418, & 140595 ***** Please compare the parts in the box with the bill of materials provided ***** (view the following pages)
More informationRemove four nuts, then the cooling fan assembly.
The DOHC and SOHC engines both use the same Service and Repair procedure from Isuzu. Make note that the DOHC and SOHC engines both use a single gear for the camshaft but use different alignment marks.
More informationExhaust System Installation for Audi S4, S5 & S5 Sportback PNs ,
Exhaust System Installation for Audi S4, S5 & S5 Sportback PNs 140740, 140749 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts necessary
More information2015+ Mustang GT V8 X-Pipe Exhaust Kit Installation Instructions P/N: (99-137)
2015+ Mustang GT V8 X-Pipe Exhaust Kit Installation Instructions P/N: 422046 (99-137) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Mustang GT V8 X-Pipe Exhaust Kit Installation Instructions
More information15-17 FORD MUSTANG GT
15-17 FORD MUSTANG GT IMPORTANT! WARRANTY AND Please Forward All Information to Consumer Be sure to review the enclosed instructions prior to beginning the installation process. If you have any questions
More informationThank you for purchasing a Borla Performance Cat-Back Exhaust System.
Thank you for purchasing a Borla Performance Cat-Back Exhaust System. Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing
More informationPage 1 of 8 2012 Ford F450 Super Duty 6.7L Eng Service Manual: ENGINE MECHANICAL - 6.7L DIESEL -- F250-F550 SUPER DUTY IN-VEHICLE REPAIR > OIL PAN - LOWER MATERIAL SPECIFICATIONS Item Motorcraft SAE 0W-30
More informationBanks Monster Exhaust System Ford Power Stroke 6.7L Turbo-Diesel F-250/F-350/F-450 Trucks
with Installation Instructions Owner smanual Banks Monster Exhaust System 2017+ Ford Power Stroke 6.7L Turbo-Diesel F-250/F-350/F-450 Trucks THIS MANUAL IS FOR USE WITH SYSTEM 49794 Step-by-step installation
More informationSubaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More information6.7L Cummins EGR Delete
6.7L Cummins EGR Delete H I A B E C D F J K G L PACKING LIST: Part# A B C D E F G H I J K L QTY. 4 Description Coolant Hose Coolant Hose Connector M0 Flange Nut 5/6 Bolts, Nuts, and Flat Washers /4-0 Bolt,
More informationInstallation Guide for Chevrolet Camaro ZL1 PNs ,
Installation Guide for Chevrolet Camaro ZL1 PNs -140726, 140727 ***** Please compare the parts in the box with the bill of materials provided ***** (view the following pages) to assure that you have all
More information2007 Shelby GT500 Long Tube Headers Installation
2007 Shelby GT500 Long Tube Headers Installation Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance
More information2000 Toyota Truck Tundra. Timing Belt: Service and Repair
Timing Belt: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY 4. REMOVE THROTTLE BODY COVER 5. REMOVE INTAKE AIR CONNECTOR ASSEMBLY 6. REMOVE
More informationOwner smanual. Banks Monster Split-Dual Exhaust System Ford Power Stroke 6.0L Turbo-Diesel F250/F350 Trucks. with Installation Instructions
Owner smanual with Installation Instructions Banks Monster Split-Dual Exhaust System 2003-2007 Ford Power Stroke 6.0L Turbo-Diesel F250/F350 Trucks THIS MANUAL IS FOR USE WITH Systems 47600-47614, 48761,
More information