Oil Pan Replacement Buick Regal

Size: px
Start display at page:

Download "Oil Pan Replacement Buick Regal"

Transcription

1 2000 Buick Regal Oil Pan Replacement Removal Procedure Tools Required J A Engine Support Adapters J B Universal Engine Support Fixture J A Engine Support Adapter Leg Set 1. Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Engine Electrical. 2. Carefully disconnect the throttle body air inlet duct. 3. Remove the engine mount struts from the engine. Refer to Engine Mount Strut Replacement. 4. Remove the drive belt. Refer to Drive Belt Replacement. 5. Install the J A, the J B and the J A. Do not raise the engine. Refer to Engine Support Fixture. 6. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 7. Disconnect the three-way catalytic converter pipe from the right exhaust manifold. Refer to Catalytic Converter Replacement in Engine Exhaust. 8. Remove the right front tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 9. Remove the right engine splash shield. Refer to Splash Shield Replacement - Engine in Body Front End. 10. Drain the engine oil. Refer to Engine Oil and Oil Filter Replacement. 11. Remove the oil filter. Refer to Engine Oil and Oil Filter Replacement.

2 12. Remove the AC compressor bracket bolts. Reposition and secure the AC compressor. 13. Disconnect the power steering oil cooler pipe brackets from the frame. 14. Remove the engine mount bracket bolts from the engine. Refer to Engine Mount and Bracket Replacement. 15. Remove the lower engine mount nuts. Refer to Engine Mount and Bracket Replacement. 16. Remove the torque converter cover. Refer to Torque Converter Cover Replacement in Automatic Transaxle - 4T65-E. 17. Disconnect the oil level sensor wiring harness connector. Notice Remove the oil level sensor, located in the oil pan, before the oil pan is removed. The sensor may be damaged if the oil pan is removed first. 18. Remove the oil level sensor. 19. Lower the vehicle. 20. Use the J B in order to raise the engine for access.

3 21. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 22. Suitably support the frame. Loosen the left side frame bolts. Remove the right side frame bolts. Lower the frame for access. Refer to Frame Removal in Frame and Underbody. 23. Remove the engine mount and the engine mount bracket. 24. Remove the oil pan retaining bolts. 25. Remove the oil pan. 26. Remove the oil pump pipe and screen assembly and the oil pan gasket. 27. Clean the following parts: The oil pan flanges The oil pan rail The front cover The rear main bearing cap The threaded holes Installation Procedure Notice

4 Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems. Notice Install the oil level sensor, located in the oil pan, after the oil pan is installed. The sensor may be damaged if the oil level sensor is installed first. 1. Install the oil pan gasket and the oil pump pipe and screen assembly. Tighten Tighten the oil pump pipe and screen bolts to 15 N m (11 lb ft).

5 2. Install the oil pan. 3. Clean the oil pan bolts and apply one drop of thread lock compound GM P/N or equivalent to the oil pan bolt threads. Important Do not overtighten bolts or damage to the oil pan may occur, resulting in an oil leak. 4. Install the oil pan bolts. Tighten Tighten the oil pan bolts to 14 N m (125 lb in). 5. Place the engine mount bracket and the engine mount to the proper position. Install the engine mount bracket bolts to the engine. Refer to Engine Mount and Bracket Replacement. 6. Install new right side frame bolts. Make sure the frame is suitably supported. Install new left side frame bolts. Refer to Frame Removal in Frame and Underbody. 7. Lower the vehicle. 8. Use the J B in order to lower the engine. 9. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 10. Install the lower engine mount nuts. Tighten Tighten the lower engine mount nuts to 47 N m (35 lb ft). 11. Install the oil level sensor. Tighten Tighten the oil level sensor to 20 N m (15 lb ft). 12. Connect the oil level sensor wiring harness connector. 13. Install the torque converter cover. Refer to Torque Converter Cover Replacement in Automatic Transaxle - 4T65-E. 14. Connect the power steering oil cooler pipe brackets to the frame.

6 15. Install the AC compressor bracket bolts. Refer to Compressor Replacement in HVAC. 16. Install the new oil filter. Refer to Engine Oil and Oil Filter Replacement. 17. Install the oil pan drain plug. Tighten Tighten the oil pan drain plug to 30N m (22 lb ft). 18. Install the right engine splash shield. Refer to Splash Shield Replacement - Engine in Body Front End. 19. Install the right front tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. 20. Connect the three-way catalytic converter pipe to the right exhaust manifold. Refer to Catalytic Converter Replacement in Engine Exhaust. 21. Lower the vehicle. 22. Remove the J B, the J A and the J A. 23. Install the drive belt. Refer to Drive Belt Replacement. 24. Install the engine mount struts to the engine. Refer to Engine Mount Strut Replacement. 25. Carefully install the throttle body air inlet duct. 26. Fill the crankcase with new engine oil. Refer to Engine Oil and Oil Filter Replacement. 27. Connect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in

7 Engine Electrical. 28. Inspect for the proper fluid levels. 29. Inspect for leaks. 30. Measure the wheel alignment. Refer to Wheel Alignment Specifications and Measuring Wheel Alignment in Wheel Alignment.

Page 1 of 5 2004 Pontiac GRAND PRIX Submodel: Engine Type: V6 Liters: 3.8 Fuel Delivery: FI Fuel: GAS Oil Pan Replacement Removal Procedure Disconnect the negative battery cable. Refer to Battery Negative

More information

Lower Intake Manifold Replacement

Lower Intake Manifold Replacement Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the

More information

COMPONENT LOCATOR > DISASSEMBLED VIEWS

COMPONENT LOCATOR > DISASSEMBLED VIEWS Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine

More information

Generator Replacement (LA1)

Generator Replacement (LA1) Page 1 of 5 2004 Buick Rendezvous - FWD Aztek, Rendezvous VIN A/B Service Manual Engine Engine Electrical Repair Instructions Document ID: 1407779 Generator Replacement (LA1) Removal Procedure 1. Remove

More information

Page 1 of 8 Section 03-01: Engine, 4.6L IN-VEHICLE SERVICE 1994 Town Car/Crown Victoria/Grand Marquis Workshop Manual Oil Pan and Oil Pump Screen Cover and Tube Town Car Removal 1. Disconnect battery ground

More information

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary. Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

More information

1 of 12 10/5/2015 8:11 AM

1 of 12 10/5/2015 8:11 AM 1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant

More information

2001 Chevrolet Corvette V8-5.7L VIN G

2001 Chevrolet Corvette V8-5.7L VIN G 1 of 14 2/21/2013 10:34 AM 2001 Chevrolet Corvette V8-5.7L VIN G Vehicle» Engine, Cooling and Exhaust» Engine» Oil Pan» Service and Repair Oil Pan Replacement Removal Procedure 1. 2. 3. Remove the front

More information

Intake Manifold Replacement

Intake Manifold Replacement Document ID# 738735 2002 Chevrolet Chevy Suburban - 4WD Print Intake Manifold Replacement Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may

More information

2001 Chevrolet CORVETTE

2001 Chevrolet CORVETTE riveline Support Assembly Replacement (Automatic Transmission) 1 of 21 10/24/2012 8:58 PM 2001 Chevrolet CORVETTE Submodel: Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Driveline Support Assembly

More information

Intake Manifold Replacement

Intake Manifold Replacement Page 1 of 14 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, and 6.0L Repair Instructions - On Vehicle Document ID:

More information

Front and Rear Suspension Modification Kit Installation

Front and Rear Suspension Modification Kit Installation Page 1 of 12 2014 Chevrolet Sonic (US/Canada) Sonic US/Canada Accessory Installation Manual Accessories Performance Accessories Accessories Document ID: 3471343 Front and Rear Suspension Modification Kit

More information

Engine Oil Cooler Hose/Pipe Replacement (4WD)

Engine Oil Cooler Hose/Pipe Replacement (4WD) Page 1 of 9 1998 Chevrolet Blazer - 4WD Blazer, Bravada, Jimmy, S10 Pickup, Sonoma (VIN S/T) Service Manual Engine Engine Mechanical - 4.3L Repair Instructions Document ID: 179331 Engine Oil Cooler Hose/Pipe

More information

2000 Chevrolet Blazer

2000 Chevrolet Blazer HEATER CORE Removal Procedure 1. Remove the heater/vent module. Refer to HEATER/VENT MODULE. 2. Remove the heater core access cover screws. Fig. 14: Identifying Heater Core Access Cover & Screws 3. Remove

More information

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting

More information

1991 Volkswagen Vanagon Syncro

1991 Volkswagen Vanagon Syncro corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at

More information

Disconnect the breather tube from the air cleaner outlet duct.

Disconnect the breather tube from the air cleaner outlet duct. Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from

More information

Engine Removal and Installation

Engine Removal and Installation Page 1 of 5 Home Account Contact ALLDATA Log Out Help TINO TORRES Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Chrysler Sebring Sedan V6-2.7L VIN R Conversion Calculator Vehicle

More information

This information covers the proper replacement procedure for the EGR valve on the Volvo D16F engine.

This information covers the proper replacement procedure for the EGR valve on the Volvo D16F engine. Volvo Trucks North America Greensboro, NC USA EGR Valve, Replacement DService Bulletin Trucks Date Group No. Page 11.2006 254 24 1(17) EGR Valve Replacement D16F W2005772 This information covers the proper

More information

Page 1 of 6 Section 07-01A: Transaxle, Automatic CD4E 1996 Probe Workshop Manual REMOVAL Procedure revision date: 06/14/2000 Transaxle Item Part Number Description 1 10655 Battery 2 10732 Battery Tray

More information

2003 F-Super Duty /Excursion Workshop Manual

2003 F-Super Duty /Excursion Workshop Manual Page 1 of 7 SECTION 303-04F: Fuel Charging and Controls Turbocharger, 6.0L Diesel 2003 F-Super Duty 250-550/Excursion Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Turbocharger

More information

Solenoid Valve VCB, Replacement, D13F. This information covers the procedures for replacing the VCB solenoid valve on the Volvo D13F engine.

Solenoid Valve VCB, Replacement, D13F. This information covers the procedures for replacing the VCB solenoid valve on the Volvo D13F engine. Volvo Trucks North America Greensboro, NC USA DService Bulletin Trucks Date Group No. Page 10.2007 253 67 1(9) Solenoid Valve VCB, Replacement D13F Solenoid Valve VCB, Replacement, D13F This information

More information

1 of 8 12/12/2012 6:08 PM 1999 Chevrolet Express - 2WD Express, Savana VIN G Service Manual Engine Engine Mechanical - 6.5L Repair Instructions Engine Replacement Removal Procedure Tools Required J 36857

More information

3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter

3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter 1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower

More information

2003 Volkswagen Passat GL

2003 Volkswagen Passat GL 2001-03 AUTOMATIC TRANSMISSIONS Removal & Installation - 01V APPLICATION TRANSAXLE APPLICATION Application Transaxle Model Passat 1.8L (FWD) 01V 2.8L (FWD & 4WD) 01V 4.0L (AWD) 2002-03 01V REMOVAL & INSTALLATION

More information

303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine

303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine 2010 MKZ Report a problem with this article 303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid REMOVAL Procedure revision date: 10/19/2012 Engine Special Tool(s) 2,200# Floor Crane,

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove

More information

Disconnect negative battery cable and remove coolant bottle cap.

Disconnect negative battery cable and remove coolant bottle cap. 1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use

More information

Fastener Tightening Specifications Specification

Fastener Tightening Specifications Specification 2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt

More information

2. Remove the intake manifold cover. Refer to Intake Manifold Cover Replacement.

2. Remove the intake manifold cover. Refer to Intake Manifold Cover Replacement. VALVE COVER GASKET Valve Rocker Arm Cover Replacement - Left Side Removal Procedure 1. Partially drain the cooling system. Refer to Cooling System Draining and Filling (LZE, LZ4, LZG, 9C1, 9C3, GE47716

More information

Cylinder Head Installation - Left Side

Cylinder Head Installation - Left Side Cylinder Head Installation - Left Side Tools Required J 36660-A Torque Angle Meter 1. Install the cylinder head locator dowel pins, if necessary. 2. Inspect the cylinder head locator dowel pins for proper

More information

EXHAUST SYSTEM AND INTAKE MANIFOLD

EXHAUST SYSTEM AND INTAKE MANIFOLD J EXHAUST SYSTEM AND INTAKE MANIFOLD 11-1 EXHAUST SYSTEM AND INTAKE MANIFOLD CONTENTS page EXHAUST SYSTEM... 1 EXHAUST SYSTEM DIAGNOSIS... 2 page SERVICE PROCEDURES... 3 TORQUE SPECIFICATIONS... 10 EXHAUST

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Valve Cover» Service and Repair» Procedures» RH Valve Cover RH Removal 1. Disconnect the battery ground cable. 2. Remove the air cleaner

More information

M-9424-M50B 2012 Boss 302 Intake Manifold INSTALLATION INSTRUCTIONS

M-9424-M50B 2012 Boss 302 Intake Manifold INSTALLATION INSTRUCTIONS !!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. WARNING: CUSTOM CALIBRATION REQUIRED! CALIBRATION NOT INCLUDED! KIT CONTENTS: 1) Intake Manifold Assembly 2) Assembly

More information

1 of 14 11/19/ :45 AM

1 of 14 11/19/ :45 AM 1 of 14 11/19/2016 11:45 AM 6F35 Digital Transmission Range (TR) Sensor Removal All vehicles 1. With the vehicle in NEUTRAL, position it on a hoist. 3.0L engine 2. Remove the Air Cleaner (ACL) outlet pipe.

More information

Cylinder Head Replacement

Cylinder Head Replacement CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A

More information

Engine Cylinder Head Installation

Engine Cylinder Head Installation Engine Cylinder Head Installation Important: Install the cylinder head without the camshafts. 1. Install the engine cylinder head to the engine block. 2. Install the AIR pump bolt and fir tree fastener

More information

1990 Buick Electra Limited

1990 Buick Electra Limited 4. To install remaining components, reverse removal procedure. Coat rocker arm bolts with GM Threadlock (12345493) prior to installation. Fig. 3: Cylinder Head Bolt Tightening Sequence FRONT CRANKSHAFT

More information

2004 DRIVELINE/AXLE. Rear Drive Axle - Corvette. Fastener Tightening Specifications Specification Application

2004 DRIVELINE/AXLE. Rear Drive Axle - Corvette. Fastener Tightening Specifications Specification Application 2004 DRIVELINE/AXLE Rear Drive Axle - Corvette SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Differential Case Bolts 55 N.m

More information

Page 1 of 14 Oil Pan Removal & Installation 4.2L Engine 4WD Vehicles To Remove: 1. Before servicing the vehicle refer to the precautions at the beginning of this section. 2. Raise and support the vehicle.

More information

This information covers the proper procedure for replacing the intake manifold gasket on the Volvo D16F engine.

This information covers the proper procedure for replacing the intake manifold gasket on the Volvo D16F engine. Volvo Trucks North America Greensboro, NC USA DService Bulletin Trucks Date Group No. Page 2.2007 251 39 1(14) Intake Manifold Gasket Replacement D16F Intake Manifold Gasket Replacement W2005773 This information

More information

1998 Contour/Mystique Workshop Manual

1998 Contour/Mystique Workshop Manual SECTION 30-01: Automatic Transmission/Transaxle 1998 Contour/Mystique Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 09/14/2001 Main Controls Special Tool(s) Aligner, Selector Shaft 30-S290

More information

THIS BULLETIN IS BEING PROVIDED IN ADVANCE. DO NOT ORDER PARTS OR PERFORM ANY ACTIONS RELATED TO THIS BULLETIN UNTIL JANUARY 15, 2008.

THIS BULLETIN IS BEING PROVIDED IN ADVANCE. DO NOT ORDER PARTS OR PERFORM ANY ACTIONS RELATED TO THIS BULLETIN UNTIL JANUARY 15, 2008. NUMBER: 24-008-07 GROUP: Heating & A/C DATE: December 18, 2007 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,

More information

Intake Manifold Removal (Upper)

Intake Manifold Removal (Upper) Intake Manifold Removal (Upper) Disconnect the vacuum lines from the upper intake manifold. Disconnect the MAP sensor electrical connector. Remove the MAP sensor screws. Remove the MAP sensor. Remove the

More information

CLUTCH Toyota Celica DESCRIPTION ADJUSTMENTS CLUTCH PEDAL HEIGHT Clutch. Celica

CLUTCH Toyota Celica DESCRIPTION ADJUSTMENTS CLUTCH PEDAL HEIGHT Clutch. Celica CLUTCH 1993 Toyota Celica 1993 Clutch Celica DESCRIPTION The single, dry disc type clutch uses a hydraulically operated master cylinder and a release cylinder mounted on clutch housing. Clutch release

More information

Installation Instructions

Installation Instructions Installation Instructions Transverse K04 Tools Required Jack and jack stands Drain pan for coolant and oil 3" and 6" extensions Channel locks 7mm, 8mm, 10mm, 11mm, 12mm, 13mm, and 16mm sockets Oxygen sensor

More information

Engine Removal/Installation

Engine Removal/Installation Engine Removal/Installation Make sure jacks and safety stands are placed properly and hoist brackets are attached to correct positions on the engine. (See Section 1). Apply parking brake and block rear

More information

DESCRIPTION AND OPERATION

DESCRIPTION AND OPERATION 303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589

More information

2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...

2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin... Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine

More information

GM 4T65E Installation Tips

GM 4T65E Installation Tips GM 4T65E Installation Tips WARNING: DO NOT operate vehicle without installing a new transmission oil cooler. We recommend installing a Hayden 1403 or 1404. Bypass the radiator and install the new cooler.

More information

Catalytic Converter: Service and Repair

Catalytic Converter: Service and Repair 2007 GMC Truck Envoy 4WD V8-5.3L Copyright 2009, ALLDATA 10.10 Page 1 Catalytic Converter: Service and Repair Catalytic Converter Replacement (5.3L and 6.0L Engines) Removal Procedure 1. Raise and suitably

More information

REMOVAL. Fig Sized for Print

REMOVAL. Fig Sized for Print ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting

More information

Engine Front Cover. Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1) or equivalent. Support Bar, Engine 303-F070

Engine Front Cover. Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1) or equivalent. Support Bar, Engine 303-F070 SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Engine Front Cover Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1)

More information

M-5220-MB Mustang GT Side Exhaust Kit INSTALLATION INSTRUCTIONS

M-5220-MB Mustang GT Side Exhaust Kit INSTALLATION INSTRUCTIONS Please visit www.fordracingparts.com for the most current instruction information.!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

Installation Instructions and Warranty Information

Installation Instructions and Warranty Information Corporate Office: PerTronix Inc. 440 E. Arrow Highway, San Dimas, California 91773 * Phone 909.599.5955 FAX 909.599.6424 Installation Instructions and Warranty Information 6695S 2007-14 5.4/5.8 Ford Mustang

More information

Torque Guidelines (Z 22 SE)

Torque Guidelines (Z 22 SE) Page 1 of 14 Torque Guidelines (Z 22 SE) No. Designation Nm 1 Retaining bolts, coolant pump sprocket to coolant pump 2 Retaining bolts, balancer shaft timing chain guide rail to 3 Retaining bolts, balancer

More information

2005 Chevrolet Equinox Equinox VIN L Service Manual Engine Engine Mechanical - 3.4L Repair Instructions - On Vehicle Document ID:

2005 Chevrolet Equinox Equinox VIN L Service Manual Engine Engine Mechanical - 3.4L Repair Instructions - On Vehicle Document ID: xtooltipelement Service Information 2005 Chevrolet Equinox Equinox VIN L Service Manual Engine Engine Mechanical - 3.4L Repair Instructions - On Vehicle Document ID: 1383623 Engine Front Cover Replacement

More information

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.

Disconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly. ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.

More information

Vehicle Level Engine, Cooling and Exhaust Engine Cylinder Head Assembly Service and Repair. Service and Repair

Vehicle Level Engine, Cooling and Exhaust Engine Cylinder Head Assembly Service and Repair. Service and Repair Page 1 of 7 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2001 Pontiac Sunfire L4-2.2L VIN 4 Conversion Calculator

More information

2001 Ranger Workshop Manual. 1. Drain the cooling system. For additional information, refer to Section

2001 Ranger Workshop Manual. 1. Drain the cooling system. For additional information, refer to Section Exhaust Gas Recirculation (EGR) Valve 2.3L 1. Drain the cooling system. For additional information, refer to Section 303-03. 2. Disconnect the battery ground cable. For additional information, refer to

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before

More information

Part # 6695S. Read all instructions carefully before attempting installation.

Part # 6695S. Read all instructions carefully before attempting installation. Corporate Office: PerTronix Inc. 440 E. Arrow Highway, San Dimas, California 91773 * Phone 909.599.5955 FAX 909.599.6424 Installation Instructions and Warranty Information 2007-10 5.4 Ford Mustang Shelby

More information

ASSEMBLY/INSTALLATION INSTRUCTIONS

ASSEMBLY/INSTALLATION INSTRUCTIONS ASSEMBLY/INSTALLATION INSTRUCTIONS AURORA 3000 & 4000 SCORPION TURBO SYSTEM NOTICE: The engine oil must be changed any time the turbocharger is removed from the engine. The passages in the block underneath

More information

Piston Cooling Nozzle, Replacement

Piston Cooling Nozzle, Replacement Volvo Trucks North America Greensboro, NC USA This Service Bulletin replaces Service Bulletin 221-49, Piston Cooling, dated (1.2007), publication no. PV776-20177472. DService Bulletin Trucks Date Group

More information

Page 1 of 5 303-01B Engine 3.0L (4V) 2004 Escape IN-VEHICLE REPAIR Procedure revision date: 05/26/2005 Engine Front Cover Material Removal Item Motocraft Metal Surface Cleaner ZC-21 Silicone Gasket and

More information

Exhaust Manifold - Remove and Install

Exhaust Manifold - Remove and Install 14 RENR7458-09 i02228217 Exhaust Manifold - Remove and Install SMCS Code: 1059-010 Illustration 25 g01124147 1. Apply ing (A) to the outside diameter of the male ends of exhaust manifold (2). Assemble

More information

Page 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description

More information

2002 F-150 Workshop Manual

2002 F-150 Workshop Manual Page 1 of 8 SECTION 307-01B: Automatic Transmission 4R70W 2002 F-150 Workshop Manual REMOVAL Procedure revision date: 04/02/2003 Transmission Special Tool(s) Retainer, Torque Converter 307-346 (T97T-7902-A)

More information

2012 Kia Soul L4 2.0L

2012 Kia Soul L4 2.0L 2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender

More information

SECTION D Fuel Charging and Controls Turbocharger

SECTION D Fuel Charging and Controls Turbocharger 303-04D-i Fuel Charging and Controls Turbocharger 303-04D-i SECTION 303-04D Fuel Charging and Controls Turbocharger CONTENTS PAGE Turbocharger Body On... 303-04D-2 303-04D-2 Fuel Charging and Controls

More information

2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.

2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages. 2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position

More information

This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.

This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis. Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers

More information

2006 Chevrolet Impala SS ENGINE Engine Electrical - Impala

2006 Chevrolet Impala SS ENGINE Engine Electrical - Impala BATTERY REPLACEMENT (RPOS LZE/LZ4/LZ9) Removal Procedure IMPORTANT: Do not tip the battery more than 40 degrees during removal. Fig. 52: View Of Negative Battery Cable Terminal & Battery 1. Disconnect

More information

Intake Components 1117

Intake Components 1117 Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold

More information

1999 Honda Accord DX

1999 Honda Accord DX Installation 1. Clean tensioner pulleys. Ensure cylinder No. 1 is at TDC by aligning dimple on timing belt drive pulley with pointer on oil pump housing. See Fig. 4. Ensure camshaft pulley TDC marks are

More information

IN-VEHICLE REPAIR. Upper Intake Manifold

IN-VEHICLE REPAIR. Upper Intake Manifold 303-01-1 Engine 3.9L and 4.2L 303-01-1 IN-VEHICLE REPAIR Upper Intake Manifold Special Tool(s) Remover, Spark Plug Wire 303-106 (T74P-6666-A) Material Item Silicone Brake Caliper Grease and Dielectric

More information

SECTION B Engine 5.0L (4V)

SECTION B Engine 5.0L (4V) 303-01B-i Engine 5.0L (4V) 303-01B-i SECTION 303-01B Engine 5.0L (4V) CONTENTS PAGE SPECIFICATIONS... 303-01B-2 303-01B-2 Engine 5.0L (4V) 303-01B-2 SPECIFICATIONS Material Motorcraft Metal Surface Prep

More information

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie

More information

Lubrication system components, removing and installing

Lubrication system components, removing and installing 17-1 Lubrication system components, removing and installing Note: If large quantities of metal particles or other deposits (caused, for example, by partial seizure of the crankshaft or conrod bearings)

More information

Exhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove

Exhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove 1 Page 1 of 20 Exhaust Gas Recirculation Valve, Replace J982500 Remove 1. Disconnect battery negative lead 2. Disconnect hose (1) from oil filler on air cleaner assembly, then move to one side Release

More information

Valve Rocker Arm and Push Rod Installation (6.2L LS3)

Valve Rocker Arm and Push Rod Installation (6.2L LS3) 9. Tighten the cylinder head bolts: 10.1. Tighten the M11 cylinder head bolts (1-10) a first pass in sequence to 30 N m (22 lb ft). 10.2. Tighten the M11 cylinder head bolts (1-10) a second pass in sequence

More information

6.7L Cummins EGR Delete

6.7L Cummins EGR Delete 6.7L Cummins EGR Delete H I A B E C D F J K G L PACKING LIST: Part# A B C D E F G H I J K L QTY. 4 Description Coolant Hose Coolant Hose Connector M0 Flange Nut 5/6 Bolts, Nuts, and Flat Washers /4-0 Bolt,

More information

FULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L

FULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L 2018-01-15 FORD F150 ECOBOOST 3.5L FULL BORE PERFORMANCE MANIFOLD SET (PART #500101X) 1 FULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L INSTALLATION INSTRUCTIONS 2011-2012 FORD F150 3.5L ECOBOOST

More information

1999 E-Series Workshop Manual

1999 E-Series Workshop Manual http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998

More information

2012 Kia Soul L4 2.0L

2012 Kia Soul L4 2.0L 2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are

More information

03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions

03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions Hellion Power Systems 03-04 Mach 1 Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation

More information

Trailer Hitch Platform Package Installation

Trailer Hitch Platform Package Installation Page 1 of 9 2014 Chevrolet Silverado 1500-2WD Sierra, Silverado VIN C/K Accessory Installation Manual Accessories Trailer Hitch Platform Package Installation Table 1: Light Duty Hitch Platform Kit Contents

More information

1 M-3000-H4 F150 4X4 Lowering Kit

1 M-3000-H4 F150 4X4 Lowering Kit READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. IT IS RECOMMENDED THAT INSTALLATION BE DONE BY A QUALIFIED MECHANIC. REPLACE ALL STOCK PARTS THAT ARE DAMAGED OR WORN. ALWAYS WEAR EYE PROTECTION.

More information

99-04 GT. Hellion Power Systems Mustang GT Kit Instructions

99-04 GT. Hellion Power Systems Mustang GT Kit Instructions Hellion Power Systems 99-04 Mustang GT Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation

More information

Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent

Cylinder Head. Special Tool(s) Compressor, Valve Spring (T93P-6565-AR) Heavy Duty Floor Crane or equivalent SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual INSTALLATION Procedure revision date: 04/03/2009 Cylinder Head Special Tool(s) Compressor, Valve Spring 303-452 (T93P-6565-AR) Heavy Duty

More information

96-04 tt. Hellion Power Systems Mustang Twin Turbo Kit Instructions

96-04 tt. Hellion Power Systems Mustang Twin Turbo Kit Instructions 96-04 tt Hellion Power Systems 1996-2004 Mustang Twin Turbo Kit Instructions 1. Disconnect battery and elevate front end of car on either Jack stands or a lift if available 2.Lock steering wheel and remove

More information

TRANSMISSION REMOVAL & INSTALLATION - A/T

TRANSMISSION REMOVAL & INSTALLATION - A/T TRANSMISSION REMOVAL & INSTALLATION - A/T 1990 Nissan 240SX 1990 TRANSMISSION SERVICING Nissan Automatic Transmission Axxess, Maxima, Pathfinder, Pickup, Pulsar NX, Sentra, Stanza, 240SX, 300ZX NOTE: For

More information

Section 7.3 Water Manifold has been updated.

Section 7.3 Water Manifold has been updated. NUMBER: 08 DD15-11 S.M. REF.: 7.3 ENGINE: DD15 DATE: September 2008 SUBJECT: WATER MANIFOLD PUBLICATION: DDC-SVC-MAN-0002 Section 7.3 Water Manifold has been updated. 7.3 WATER MANIFOLD Coolant flows from

More information

MM009 6TH GEN CAMARO MOTOR MOUNT KIT

MM009 6TH GEN CAMARO MOTOR MOUNT KIT BMR recommends professional installation of this product. A service lift is also recommended for installation of this product. If the vehicle is equipped with an oil cooler, engine coolant is drained during

More information

2013 Mustang Workshop Manual

2013 Mustang Workshop Manual 32. Attach the wiring harness retainers to the LH side of the oil pan and the front oil pan stud bolts and install the 2 nuts. Tighten to 8 Nm (71 lb-in). 33. Position the underbody shield and install

More information

MANUAL TRANSMISSIONS. Servicing - Corvette. Transmission Model (RPO Code) Borg-Warner T56 6-Speed (M12)

MANUAL TRANSMISSIONS. Servicing - Corvette. Transmission Model (RPO Code) Borg-Warner T56 6-Speed (M12) 2003-04 MANUAL TRANSMISSIONS Servicing - Corvette APPLICATION TRANSMISSION APPLICATION Application Corvette Convertible & Coupe Z06 Transmission Model (RPO Code) Borg-Warner T56 6-Speed (MM6) Borg-Warner

More information

EXHAUST SYSTEM AND INTAKE MANIFOLD

EXHAUST SYSTEM AND INTAKE MANIFOLD EXHAUST SYSTEM AND INTAKE MANIFOLD 11-1 EXHAUST SYSTEM AND INTAKE MANIFOLD CONTENTS page GENERAL INFORMATION... 1 SERVICE PROCEDURES... 4 page TORQUE SPECIFICATION... 13 EXHAUST SYSTEMS The exhaust systems

More information

SLP Camaro ZL1 STAGE 2 (625 HP)

SLP Camaro ZL1 STAGE 2 (625 HP) SLP - 2012 Camaro ZL1 STAGE 2 (625 HP) PART #26001 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1

More information

IN-VEHICLE REPAIR. Engine Front Cover

IN-VEHICLE REPAIR. Engine Front Cover 303-01B-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01B-1 Special Tool(s) Motorcraft SAE 5W-20 WSS-M2C930-A Premium Synthetic Blend 3-Jaw Puller Motor Oil 303-D121 XO-5W20-QSP

More information

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION

More information