2006 Chevrolet Impala SS ENGINE Engine Electrical - Impala

Size: px
Start display at page:

Download "2006 Chevrolet Impala SS ENGINE Engine Electrical - Impala"

Transcription

1 BATTERY REPLACEMENT (RPOS LZE/LZ4/LZ9) Removal Procedure IMPORTANT: Do not tip the battery more than 40 degrees during removal. Fig. 52: View Of Negative Battery Cable Terminal & Battery 1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure (RPOs LZE/LZ4/LZ9) or Battery Negative Cable Disconnect/Connect Procedure (RPO LS4). 2. Remove the right front diagonal brace. Refer to Brace Replacement - Front Fender Upper Diagonal. Monday, December 01, :57:32 5:57:38 PM Page Mitchell Repair Information Company, LLC.

2 3. Open the positive battery cable terminal cover (7). 4. Loosen the positive battery cable terminal nut. 5. Remove the positive battery cable terminal from the battery. Fig. 53: View Of Battery Insulator 6. Remove the battery insulator. Monday, December 01, :57:32 PM Page Mitchell Repair Information Company, LLC.

3 Fig. 54: View Of Battery Hold Down & Bolt 7. Remove the battery hold down bolt and hold down. 8. Remove the battery. Installation Procedure IMPORTANT: Do not tip the battery more than 40 degrees during installation. Monday, December 01, :57:32 PM Page Mitchell Repair Information Company, LLC.

4 Fig. 55: View Of Battery Hold Down & Bolt 1. Install the battery. NOTE: Refer to Fastener Notice. 2. Install the battery hold down and bolt. Tighten: Tighten the bolt to 18 N.m (13 lb ft). Monday, December 01, :57:32 PM Page Mitchell Repair Information Company, LLC.

5 Fig. 56: View Of Battery Insulator 3. Install the battery insulator. Monday, December 01, :57:32 PM Page Mitchell Repair Information Company, LLC.

6 Fig. 57: View Of Negative Battery Cable Terminal & Battery 4. Install the positive battery cable terminal to the battery. 5. Tighten the positive battery cable terminal nut. Tighten: Tighten the nut to 15 N.m (11 lb ft). 6. Snap closed the positive battery cable terminal cover (7). 7. Install the right front diagonal brace. Refer to Brace Replacement - Front Fender Upper Diagonal. 8. Connect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure (RPOs LZE/LZ4/LZ9) or Battery Negative Cable Disconnect/Connect Procedure (RPO LS4). Monday, December 01, :57:32 PM Page Mitchell Repair Information Company, LLC.

7 BATTERY REPLACEMENT (RPO LS4) Removal Procedure IMPORTANT: Do not tip the battery more than 40 degrees during removal. Fig. 58: Identifying Negative Battery Cable Terminal & Battery Monday, December 01, :57:32 PM Page Mitchell Repair Information Company, LLC.

8 1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure (RPOs LZE/LZ4/LZ9) or Battery Negative Cable Disconnect/Connect Procedure (RPO LS4). 2. Remove the right front diagonal brace. Refer to Brace Replacement - Front Fender Upper Diagonal. 3. Reposition the positive battery cable terminal cover (1). 4. Loosen the positive battery cable terminal nut. 5. Remove the positive battery cable terminal from the battery. Fig. 59: View Of Battery Retainer & Bolts 6. Remove the battery retainer bolts (1) and retainer (2). 7. Remove the battery. Installation Procedure Monday, December 01, :57:32 PM Page Mitchell Repair Information Company, LLC.

9 IMPORTANT: Do not tip the battery more than 40 degrees during installation. Fig. 60: View Of Battery Retainer & Bolts 1. Install the battery. NOTE: Refer to Fastener Notice. 2. Install the battery retainer (2) and bolts (1). Tighten: Tighten the bolts to 18 N.m (13 lb ft). Monday, December 01, :57:32 PM Page Mitchell Repair Information Company, LLC.

10 Fig. 61: Identifying Negative Battery Cable Terminal & Battery 3. Install the positive battery cable terminal to the battery. 4. Tighten the positive battery cable terminal nut. Tighten: Tighten the nut to 15 N.m (11 lb ft). 5. Position the positive battery cable terminal cover (2). Monday, December 01, :57:33 PM Page Mitchell Repair Information Company, LLC.

11 6. Install the right front diagonal brace. Refer to Brace Replacement - Front Fender Upper Diagonal. 7. Connect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure (RPOs LZE/LZ4/LZ9) or Battery Negative Cable Disconnect/Connect Procedure (RPO LS4). Monday, December 01, :57:33 PM Page Mitchell Repair Information Company, LLC.

2007 Chevrolet Impala SS. IMPORTANT: When replacing battery cables be sure to use replacement cables that are the same type, gage, and length.

2007 Chevrolet Impala SS. IMPORTANT: When replacing battery cables be sure to use replacement cables that are the same type, gage, and length. BATTERY POSITIVE AND NEGATIVE CABLE REPLACEMENT (RPO LS4) Removal Procedure IMPORTANT: When replacing battery cables be sure to use replacement cables that are the same type, gage, and length. Fig. 24:

More information

2007 Dodge Caliber SE

2007 Dodge Caliber SE REAR DOOR Fig. 69: REAR DOOR HINGE 1. With the help of an assistant, carefully remove nuts (1) from door studs. 2. Remove door (7) from vehicle. 3. Disconnect door harness (4). Fig. 70: REAR DOOR HINGE

More information

2006 Saturn Ion ACCESSORIES & EQUIPMENT Doors - Ion

2006 Saturn Ion ACCESSORIES & EQUIPMENT Doors - Ion POWER DOOR LOCK SWITCH REPLACEMENT Removal Procedure Fig. 28: View Of Power Door Lock Switch 1. Using a flat-bladed tool, pry the switch from the door trim panel enough to expose the locking tabs. 2. Press

More information

2003 Chevrolet Impala LS

2003 Chevrolet Impala LS MULTIFUNCTION, TURN SIGNAL SWITCH REPLACEMENT Removal Procedure Fig. 28: View Of Steering Column Wire Harness Assembly & Wire Harness Strap CAUTION: Refer to SIR Caution in Cautions and Notices. Tuesday,

More information

2003 Chevrolet Impala

2003 Chevrolet Impala IGNITION SWITCH LOCK CYLINDER REPLACEMENT Removal Procedure IMPORTANT: Perform the body control module (BCM) theft deterrent relearn procedure whenever you replace the ignition switch lock cylinder. 1.

More information

1999 Honda Accord DX

1999 Honda Accord DX Installation 1. Clean tensioner pulleys. Ensure cylinder No. 1 is at TDC by aligning dimple on timing belt drive pulley with pointer on oil pump housing. See Fig. 4. Ensure camshaft pulley TDC marks are

More information

2004 Chevrolet Silverado 3500

2004 Chevrolet Silverado 3500 CLUTCH PEDAL REPLACEMENT Removal Procedure 1. Remove the driver's side knee bolster and deflector. Refer to Knee Bolster Replacement in Instrument Panel, Gages, and Console. 2. Disconnect and reposition

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT CAUTION: DO NOT turn

More information

2003 Chevrolet Blazer

2003 Chevrolet Blazer INSTRUMENT PANEL (I/P) CARRIER REPLACEMENT Removal Procedure 1. On vehicles equipped with a manual transmission, remove the shift lever. Refer to CONTROL LEVER AND/OR BOOT REPLACEMENT in Manual Transmission

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect

More information

COMPONENT LOCATOR > DISASSEMBLED VIEWS

COMPONENT LOCATOR > DISASSEMBLED VIEWS Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine

More information

2003 Ford Focus ZTW SUSPENSION Front - Focus

2003 Ford Focus ZTW SUSPENSION Front - Focus HUB/STEERING KNUCKLE ASSEMBLY Removal 1. Loosen the strut tower nuts by at least five turns. See Fig. 4. Loosen the wheel hub retaining nut. Raise and support vehicle. Remove front wheel, brake caliper

More information

PGM-FI MAIN RELAY CIRCUIT TROUBLESHOOTING

PGM-FI MAIN RELAY CIRCUIT TROUBLESHOOTING PGM-FI MAIN RELAY CIRCUIT TROUBLESHOOTING 1. Turn the ignition switch OFF, then disconnect the PGM-FI main relay 7P connector. 2. Check for continuity between body ground and PGM-FI main relay 7P connector

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. On Millenia, raise and support vehicle. Remove right front wheel. Remove lower engine covers. 2. On all models, remove accessory

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2.

More information

2006 Ford Pickup F350 Super Duty

2006 Ford Pickup F350 Super Duty Fig. 100: Identifying Evaporator Core Housing Components Removal All vehicles 1. Remove the suction accumulator. For additional information, refer to SUCTION ACCUMULATOR. 2. Remove the RH battery. For

More information

2002 Mitsubishi Montero Limited

2002 Mitsubishi Montero Limited Fig. 9: Removing Drive Belt Auto Tensioner (2001-02 Montero) Sunday, December 07, 2008 2:19:07 2:19:11 PM Page 1 2005 Mitchell Repair Information Company, LLC. Fig. 10: Exploded View Of Timing Belt Components

More information

2002 Jeep Grand Cherokee Laredo

2002 Jeep Grand Cherokee Laredo Removal WARNING: DO NOT REMOVE THE CYLINDER BLOCK DRAIN PLUGS OR LOOSEN THE RADIATOR DRAINCOCK WITH THE SYSTEM HOT AND UNDER PRESSURE. SERIOUS BURNS FROM COOLANT CAN OCCUR. REFER TO COOLING SYSTEM DRAINING.

More information

FUEL-FILLER LID REMOVAL/INSTALLATION

FUEL-FILLER LID REMOVAL/INSTALLATION 2005 ACCESSORIES & EQUIPMENT Body Panels - MX-5 Miata FUEL-FILLER LID REMOVAL/INSTALLATION 1. Remove the bolts, then remove the fuel-filler lid. Fig. 1: Removing Fuel-Filler Lid 2. Install in the reverse

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Noting position for installation reference, disconnect secondary wires from spark plugs. Remove spark plugs. 2. Disconnect negative battery cable. Remove air

More information

2003 Dodge Dakota ENGINE PERFORMANCE Removal & Installation - Dakota

2003 Dodge Dakota ENGINE PERFORMANCE Removal & Installation - Dakota FUEL LINE DISCONNECT FITTINGS NOTE: Fuel lines may contain single tab, dual tab or plastic retainer ring disconnect fitting. Determine type of disconnect fitting used and use proper procedure for proper

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect

More information

2001 Dodge Pickup R2500

2001 Dodge Pickup R2500 FUEL INJECTION PUMP Removal CAUTION: High-pressure fuel lines must be clamped securely and routed so they do not contact each other or any other components. DO NOT weld or switch high-pressure fuel lines.

More information

DOOR PANEL REMOVAL/INSTALLATION

DOOR PANEL REMOVAL/INSTALLATION DOOR PANEL REMOVAL/INSTALLATION Special Tools Required KTC trim tool set SOJATP2014 Trim pad remover, Snap-on A177A, or equivalent, commercially available. 2-DOOR NOTE: Use the appropriate tool from the

More information

2005 Chrysler 300 C ENGINE Mechanical - 3.5L - Service Information & Magnum

2005 Chrysler 300 C ENGINE Mechanical - 3.5L - Service Information & Magnum 1. Install camshaft sprockets onto the camshafts. Install NEW sprocket attaching bolts into place. The 255 mm (10 in.) bolt is to be installed in the left camshaft and the 213 mm (8 3/8 in.) bolt is to

More information

2005 Saturn L ENGINE Engine Mechanical - 3.0L (L81) - L300

2005 Saturn L ENGINE Engine Mechanical - 3.0L (L81) - L300 Crankcase Vent Housing Removal Fig. 324: Removing & Installing Engine Vent Housing 1. Remove the hoses from the chamber. 2. Remove the chamber bolts. 3. Remove the chamber. 4. Remove the gasket material.

More information

1999 Dodge Caravan ENGINE PERFORMANCE Self-Diagnostics - Caravan, Town & Country, & Voyager

1999 Dodge Caravan ENGINE PERFORMANCE Self-Diagnostics - Caravan, Town & Country, & Voyager 1. Attempt to start engine. If engine does not start, go to next step. If engine starts, go to step 4. 2. Turn ignition off. Disconnect connectors at Powertrain Control Module (PCM). PCM is located between

More information

TORQUE SPECIFICATIONS

TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket Bolts Upper Vertical Bolt 16-21 (22-29) Horizontal Bolts 32-43 (43-58) A/C Compressor-To-Bracket Bolts 32-43

More information

2006 Chrysler Pacifica

2006 Chrysler Pacifica HALOGEN HEADLAMP Fig. 15: Halogen Headlamp Unit 1 - HEADLAMP HIGH BEAM 2 - HEADLAMP LOW BEAM 1. Remove the headlamp unit (Refer to ELECTRICAL/LAMPS/LIGHTING - EXTERIOR/HEADLAMP UNIT - REMOVAL). 2. Disconnect

More information

Oil Pan Replacement Buick Regal

Oil Pan Replacement Buick Regal 2000 Buick Regal Oil Pan Replacement Removal Procedure Tools Required J 28467-90A Engine Support Adapters J 28467-B Universal Engine Support Fixture J 36462-A Engine Support Adapter Leg Set 1. Disconnect

More information

2006 Hyundai Tiburon GT

2006 Hyundai Tiburon GT Fig. 5: Identifying Clutch Cover & Disc Component With Torque Specifications REMOVAL 1. Drain the clutch fluid and transaxle gear oil. 2. Remove the transaxle assembly. 3. Insert the special tool (09411-25000)

More information

2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.

2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right

More information

1992 Toyota Cressida

1992 Toyota Cressida Monday, May 16, 2016 5:32:47 PM Page 13 2005 Mitchell Repair Information Company, LLC. Fig. 7: Exploded View Of Typical Cylinder Head & Components Fig. 8: Cylinder Head Bolt Removal Sequence Monday, May

More information

2001 Dodge Dakota ENGINES 4.7L V8

2001 Dodge Dakota ENGINES 4.7L V8 FRONT COVER Removal & Installation 1. Disconnect negative battery cable. Remove drive belt. Remove A/C compressor mounting bolts, and position compressor aside. Drain cooling system. Remove radiator hoses.

More information

2001 Chrysler Sebring LX. This procedure also covers condition where power window cables become disconnected.

2001 Chrysler Sebring LX. This procedure also covers condition where power window cables become disconnected. POWER WINDOW MOTOR NOTE: This procedure also covers condition where power window cables become disconnected. Removal Remove window regulator. See WINDOW REGULATOR. Remove 2 screws attaching metal cover

More information

ALLDATA Online Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12. Service and Repair

ALLDATA Online Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12. Service and Repair ALLDATA Online - 2000 Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component

More information

2003 Cadillac DeVille DTS

2003 Cadillac DeVille DTS TRIM PANEL REPLACEMENT - SIDE FRONT DOOR Tools Required J 36796 Clip Zip Clip Removal Tool, or J 38778 Door Trim Pad Clip Remover Removal Procedure 1. Position the window fully downward. 2. Ensure the

More information

2007 Pontiac G BRAKES Disc Brakes - G6

2007 Pontiac G BRAKES Disc Brakes - G6 REAR DISC BRAKE PADS REPLACEMENT Removal Procedure CAUTION: Refer to Brake Dust Caution. 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between

More information

See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( )

See SPECIFICATIONS & PROCEDURES article in WHEEL ALIGNMENT. Lower Ball Joint 1-22 ( ) Upper Ball Joint 6-39 ( ) Page 1 of 9 ARTICLE BEGINNING DESCRIPTION Front suspension uses coil springs with integral shock absorbers. Coil springs are mounted between the upper control arms and vehicle frame. A stabilizer bar controls

More information

DOOR LOCKS, TRUNK LID & FUEL DOOR - POWER. Entire Article

DOOR LOCKS, TRUNK LID & FUEL DOOR - POWER. Entire Article ARTICLE BEGINNING 1999-2000 ACCESSORIES & EQUIPMENT Lexus Power Door Locks, Trunk Lid & Fuel Door RX300 DESCRIPTION POWER DOOR LOCKS All doors can be locked and unlocked from either front door using control

More information

INSTALLING AND REMOVING THE HEATING/AIR-CONDITIONING UNIT

INSTALLING AND REMOVING THE HEATING/AIR-CONDITIONING UNIT INSTALLING AND REMOVING THE HEATING/AIR-CONDITIONING UNIT REMOVAL 1. Remove the covers over the heating/air-conditioning system, battery and fluid tank. Disconnect and remove the battery. 2. Remove the

More information

1993 Jeep Grand Cherokee. WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES 1993 WHEEL ALIGNMENT Chrysler Corp. - Specifications & Procedures

1993 Jeep Grand Cherokee. WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES 1993 WHEEL ALIGNMENT Chrysler Corp. - Specifications & Procedures ADJUSTMENTS CAMBER MEASUREMENT Check camber to determine if any components are bent or damaged. Camber angle is NOT adjustable. If angle is not to specification, components causing problem must be replaced.

More information

1998 Volkswagen Golf GL

1998 Volkswagen Golf GL Removal (Thermo Tensioner Roller - 1997 & Up) CAUTION: To prevent valves from contacting piston, DO NOT rotate camshaft or crankshaft with timing belt removed. Valve damage may result. 1. Remove air cleaner

More information

2000 Chevrolet Blazer

2000 Chevrolet Blazer HEATER CORE Removal Procedure 1. Remove the heater/vent module. Refer to HEATER/VENT MODULE. 2. Remove the heater core access cover screws. Fig. 14: Identifying Heater Core Access Cover & Screws 3. Remove

More information

2005 Cadillac CTS BRAKES Disc Brakes - CTS

2005 Cadillac CTS BRAKES Disc Brakes - CTS Removal Procedure 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid

More information

2006 Jeep Commander ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Service Information - Commander

2006 Jeep Commander ACCESSORIES AND EQUIPMENT Lamps/Lighting - Exterior - Service Information - Commander REMOVAL BULB Fig. 58: Remove/Install Rear Lamp Unit Bulbs NOTE: The rear lamp unit (1) contains four bulbs. For domestic vehicles they are: backup (2), park/stop (3), park/turn signal (4) and rear side

More information

2005 Cadillac CTS BRAKES Disc Brakes - CTS

2005 Cadillac CTS BRAKES Disc Brakes - CTS Removal Procedure 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid

More information

2004 Dodge Stratus ES. Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk.

2004 Dodge Stratus ES. Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk. REMOVAL - SHOCK ASSEMBLY NOTE: Access for the nuts attaching the rear shock assembly upper mount to the vehicle is through the inside of the trunk. 1. Roll back carpeting on top of the rear shock tower

More information

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Engine Electrical.

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure in Engine Electrical. 2004 GMC Envoy 4.2L Eng 1Search IGNITION SWITCH CYLINDER REQUESTED INFORMATION Ignition Lock Cylinder Replacement Removal Procedure 1. Disconnect the negative battery cable. Refer to Battery Negative Cable

More information

ARTICLE BEGINNING COMPONENTS FRONT DOOR Toyota Tacoma

ARTICLE BEGINNING COMPONENTS FRONT DOOR Toyota Tacoma Page 1 of 17 ARTICLE BEGINNING COMPONENTS Page 2 of 17 Fig. 1: Front Door Components (w/o Power Door Lock & Power Window Regulator) Page 3 of 17 Fig. 2: Front Door Components (W/ Power Door Lock & Power

More information

TIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage

TIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage Page 1 of 20 TIMING BELT REPLACEMENT Tools Required J 42492-A (KM-421-A) Timing Belt Adjuster J 45059 Angle Meter KM-470-B Angular Torque Gage Removal Procedure Fig. 37: View Of Throttle Cable CAUTION:

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (Standard Tensioner

More information

1 of 11 8/12/2015 3:23 PM

1 of 11 8/12/2015 3:23 PM 1 of 11 8/12/2015 3:23 PM ENGINE CONTROL MODULE (ECM) REPLACEMENT REMOVAL PROCEDURE NOTE: Always turn the ignition off when installing or removing the ECM connectors in order to prevent damage to the components.

More information

2004 Dodge Pickup R1500 MIL ILLUMINATION DIAGNOSTIC TROUBLE CODES P0401, P0403, P0404, P0405, P0406 TECHNICAL SERVICE BULLETIN

2004 Dodge Pickup R1500 MIL ILLUMINATION DIAGNOSTIC TROUBLE CODES P0401, P0403, P0404, P0405, P0406 TECHNICAL SERVICE BULLETIN TECHNICAL SERVICE BULLETIN Reference Number(s): 18-021-04, Date of Issue: May 4, 2004 GROUP: Vehicle Performance SUBJECT MIL Illumination Diagnostic Trouble Codes P0401, P0403, P0404, P0405, P0406 OVERVIEW

More information

1990 SUSPENSION Front ES250, LS400

1990 SUSPENSION Front ES250, LS400 SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Rotate engine clockwise and position cylinder No. 1 on TDC of compression stroke. Ensure "O" mark on crankshaft pulley aligns

More information

2005 Ford Pickup F250 Super Duty

2005 Ford Pickup F250 Super Duty Installation All vehicles CAUTION: Install new D-ring seals on the crankcase-to-head tube. It requires several hours after installation for the D-ring seals to relax back to their original size. If the

More information

1 of 5 1/10/2017 5:10 PM

1 of 5 1/10/2017 5:10 PM 1 of 5 1/10/2017 5:10 PM Shock Module Yoke Replacement ^ Tools Required - J 24319-B Steering Linkage and Tie Rod Puller Removal Procedure 1. Raise and support the vehicle. Refer to Vehicle Lifting. 2.

More information

MAXIMA DRIVER'S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD TECHNICAL SERVICE BULLETIN

MAXIMA DRIVER'S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD TECHNICAL SERVICE BULLETIN Page 1 of 11 2000-2003 MAXIMA DRIVER'S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD TECHNICAL SERVICE BULLETIN Reference Number(s): NTB02-001d, Date of Issue: December 21, 2004 NISSAN: 2000-2003 Maxima

More information

2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue

2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. 2. Raise and support vehicle. Remove right front wheel. Remove lower front splash shield. 3. Lower vehicle. Loosen,

More information

1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6

1989 Nissan 300ZX. 3.0L V6 - VIN [H] & 3.0L V6 TURBO - VIN [C] 1989 Engines - 3.0L & 3.0L Turbo V6 INTAKE MANIFOLD Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle

More information

2007 Chevrolet Suburban C1500. Excessive Engine Oil Consumption (Verify Condition, Inspect Valve Stems, Replace Cylinder Heads if Necessary)

2007 Chevrolet Suburban C1500. Excessive Engine Oil Consumption (Verify Condition, Inspect Valve Stems, Replace Cylinder Heads if Necessary) Excessive Engine Oil Consumption (Verify Condition, Inspect Valve Stems, Replace Cylinder Heads if Necessary) CONDITION: TECHNICAL SERVICE BULLETIN Reference Number(s): 07-06-01-007B, Date of Issue: July

More information

Generator Replacement (LA1)

Generator Replacement (LA1) Page 1 of 5 2004 Buick Rendezvous - FWD Aztek, Rendezvous VIN A/B Service Manual Engine Engine Electrical Repair Instructions Document ID: 1407779 Generator Replacement (LA1) Removal Procedure 1. Remove

More information

1998 Subaru Forester

1998 Subaru Forester Inspection 1. Inspect timing belt teeth for breaks, cracks or wear. Inspect belt for signs of oil contamination. When inspecting timing belt, do not bend less than a radius of 2.36" (6.0 mm). Replace belt

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING & COUNTERBALANCE SHAFT BELTS

More information

TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT

TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove belt splash shield. 4. Remove accessory drive belts.

More information

Diesel Engine - Runs Hot Towing or Pulling Grades

Diesel Engine - Runs Hot Towing or Pulling Grades ALLDATA Online - 2005 GMC Truck Sierra 3500 4WD V8-6.6L DSL Turbo VIN 2 - Di...Page 1 of 11 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's

More information

1995 Mercury Grand Marquis GS

1995 Mercury Grand Marquis GS AIR BAG SYSTEM CAUTION: Read the following safety precautions BEFORE servicing steering columns on vehicles equipped with air bag restraint system. ALWAYS wear safety glasses when servicing vehicle with

More information

1998 Honda Accord EX

1998 Honda Accord EX Installation (New Belt) 1. Ensure that engine is at TDC. Align dimple on timing belt drive pulley with pointer on oil pump. See Fig. 4. Align camshaft pulleys with pointers on back covers. 2. Remove battery

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION HEATED SEAT MODULE (HSM), MEMORY SEAT MODULE (MSM) OR MEMORY HEATED SEAT MODULE (MHSM) NOTE: After installation, initialize memory seat module. Move each power seat adjuster motor,

More information

2. Remove the intake manifold cover. Refer to Intake Manifold Cover Replacement.

2. Remove the intake manifold cover. Refer to Intake Manifold Cover Replacement. VALVE COVER GASKET Valve Rocker Arm Cover Replacement - Left Side Removal Procedure 1. Partially drain the cooling system. Refer to Cooling System Draining and Filling (LZE, LZ4, LZG, 9C1, 9C3, GE47716

More information

#PIP4158D: Low Oil Pump Pressure Due To Sticking Oil Pressure Relief Valve - (Jan 18, 2012)

#PIP4158D: Low Oil Pump Pressure Due To Sticking Oil Pressure Relief Valve - (Jan 18, 2012) Page 1 of 22 #PIP4158D: Low Oil Pump Pressure Due To Sticking Oil Pressure Relief Valve - (Jan 18, 2012) Subject: Low Oil Pump Pressure Due To Sticking Oil Pressure Relief Valve Models: 2008-2009 Buick

More information

1998 Buick Century Limited

1998 Buick Century Limited STABILIZER SHAFT LINK Removal 1. Raise and support the vehicle. 2. Disconnect the rear stabilizer shaft link from the strut. 3. Remove the rear stabilizer shaft link nut. 4. Remove the stabilizer shaft

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower

More information

A/C SYSTEM SPECIFICATIONS

A/C SYSTEM SPECIFICATIONS A/C SYSTEM SPECIFICATIONS SPECIFICATIONS Application Specification Compressor Type Matsushita Matsushita Rotary Sanden Sanden Scroll Compressor Belt Deflection (1) Used 5/16-7/16" (8-9.5 mm) New 9/32-5/16"

More information

1983 Mazda RX-7 GSL TUNE-UP' 'Mazda Rotary

1983 Mazda RX-7 GSL TUNE-UP' 'Mazda Rotary TESTING ENGINE COMPRESSION The manufacturer recommends using a special compression tester (49 0820 280K). Compression testers for piston engines will read only the highest pressure of the 3 combustion

More information

#PI0412: No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge - (Jan 12, 2012)

#PI0412: No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge - (Jan 12, 2012) Page 1 of 22 Document ID: 2608825 #PI0412: No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge - (Jan 12, 2012) Subject: No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge Models:

More information

Page 1 of 9 FRONT AXLE HUB & WHEEL BEARING Removal (Avalon, Camry, Camry Solara & Sienna) 1. 2. 3. 4. 5. 6. 7. 8. Remove front wheel. Check wheel bearing backlash and deviation (rotational free play).

More information

2002 Chevrolet Blazer

2002 Chevrolet Blazer The blower motor will operate in any switch position, as long as the ignition switch is in the RUN position and the mode switch is in any position other than OFF. When the ignition switch is on, power

More information

2002 Dodge Pickup R1500

2002 Dodge Pickup R1500 CAUTION: Overtightening the tensioner arm torx bolt can cause severe damage to the cylinder head. Tighten torx bolt to specified torque only. Install left side chain tensioner arm. Apply Mopar Lock N,

More information

3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter

3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter 1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower

More information

REPAIR INSTRUCTIONS > LOWER CONTROL ARM REPLACEMENT (1500 SERIES) > TOOLS REQUIRED

REPAIR INSTRUCTIONS > LOWER CONTROL ARM REPLACEMENT (1500 SERIES) > TOOLS REQUIRED Page 1 of 13 2007 GMC Yukon 5.3L Eng Base Service Manual: FRONT SUSPENSION SYSTEM Print Date: REPAIR INSTRUCTIONS > LOWER CONTROL ARM REPLACEMENT (1500 SERIES) > TOOLS REQUIRED J 43631 Ball Joint Separator.

More information

RIM Hood For Aeromaster Bodies

RIM Hood For Aeromaster Bodies RIM Hood For Aeromaster Bodies Service Guide WARNING: Hood should be opened by releasing the hold-down straps, lifting the hood, and engaging the prop rod. Be sure prop rod is properly engaged before working

More information

DESCRIPTION & OPERATION

DESCRIPTION & OPERATION HEADLIGHT DOORS 1998 ACCESSORIES & EQUIPMENT General Motors Corp. - Headlight Doors DESCRIPTION & OPERATION NOTE: Headlight Doors Module (HDM) may also be referred to as headlight opening door actuator

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (200SX & 300ZX)

More information

2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar

2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar COWL TOP VENT PANEL 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top

More information

INSTRUCTION BULLETIN

INSTRUCTION BULLETIN INSTRUCTION BULLETIN No. 328288 Machine: M20/T20/M30/ S30 Published: 05-2011 Rev. 00 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in

More information

Vehicle Level Engine, Cooling and Exhaust Cooling System Water Pump Service and Repair Removal. Removal

Vehicle Level Engine, Cooling and Exhaust Cooling System Water Pump Service and Repair Removal. Removal 1 of 7 4/5/2008 11:18 PM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1994 Jeep Truck Wrangler L6-242 4.0L VIN S MFI Conversion

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect

More information

Engine Removal and Installation

Engine Removal and Installation Page 1 of 5 Home Account Contact ALLDATA Log Out Help TINO TORRES Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Chrysler Sebring Sedan V6-2.7L VIN R Conversion Calculator Vehicle

More information

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components. 4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,

More information

Vehicle Level Engine, Cooling and Exhaust Engine Cylinder Head Assembly Service and Repair. Service and Repair

Vehicle Level Engine, Cooling and Exhaust Engine Cylinder Head Assembly Service and Repair. Service and Repair Page 1 of 7 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2001 Pontiac Sunfire L4-2.2L VIN 4 Conversion Calculator

More information

Body, front. Lock carrier with attachments, removing and installing

Body, front. Lock carrier with attachments, removing and installing Page 1 of 19 50-1 Body, front Lock carrier with attachments, removing and installing 1 - Hex bolt (6x) 45 Nm (33 ft lb) 2 - Hex bolt 45 Nm (33 ft lb) 3 - Hex bolt (4x) 10 Nm (7 ft lb) 4 - Hex bolts (2x)

More information

CLUTCH - HIGH EFFORT - DASH CRACKED IN CLUTCH MASTER CYLINDER AREA-VEHICLES BUILT BEFORE 6/15/90

CLUTCH - HIGH EFFORT - DASH CRACKED IN CLUTCH MASTER CYLINDER AREA-VEHICLES BUILT BEFORE 6/15/90 Page 1 of 17 HIGH CLUTCH EFFORT/CLUTCH FLUID LEAK - CRACKED MOUNT TECHNICAL SERVICE BULLETIN Reference Number(s): 90-16-7, Date of Issue: August 1, 1990 Related Ref Number(s): 90-16-7 ARTICLE BEGINNING

More information

#PI0646: Park Assist Blocked See Owners Manual Displayed in Driver Information Center (DIC) - (Jan 12, 2012)

#PI0646: Park Assist Blocked See Owners Manual Displayed in Driver Information Center (DIC) - (Jan 12, 2012) Page 1 of 45 Document ID: 2745752 #PI0646: Park Assist Blocked See Owners Manual Displayed in Driver Information Center (DIC) - (Jan 12, 2012) Subject: Park Assist Blocked See Owners Manual Displayed in

More information

1996 Toyota Camry DX ENGINE PERFORMANCE Toyota Basic Diagnostic Procedures

1996 Toyota Camry DX ENGINE PERFORMANCE Toyota Basic Diagnostic Procedures FUEL SYSTEM Basic diagnosis of fuel system should begin by checking fuel pump operation and fuel pressure. WARNING: ALWAYS release fuel pressure before disconnecting any fuel injection-related component.

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and

More information

M-5230-V6 Mustang V6 Dual Exhaust Kit INSTRUCTION SHEET

M-5230-V6 Mustang V6 Dual Exhaust Kit INSTRUCTION SHEET Please contact the Techline for the most current instruction information (800) FORD788.!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: The use of a floor hoist is

More information

2002 Honda Passport LX

2002 Honda Passport LX Fig. 151: Removing Piston Pin 11. Piston (10) Page 130 2005 Mitchell Repair Information Company, LLC. 12. Connecting rod (11) INSPECTION AND REPAIR Pistons Carefully clean away all the carbon adhering

More information

1 of 12 8/25/2017, 4:29 PM

1 of 12 8/25/2017, 4:29 PM 1 of 12 8/25/2017, 4:29 PM STANDARD PROCEDURE - WHEEL ALIGNMENT PRE-WHEEL ALIGNMENT INSPECTION Before any attempt is made to change or correct the wheel alignment, the following inspection and necessary

More information