Fastener Tightening Specifications Specification

Size: px
Start display at page:

Download "Fastener Tightening Specifications Specification"

Transcription

1 2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt 10 Y 89 lb in Camshaft Position Sensor Bolt 10 Y 89 lb in Camshaft Thrust Plate Screw 10 Y 89 lb in Clutch Pressure Plate Bolt 25 Y 18 lb ft Connecting Rod Bearing Cap Bolt 25 Y 18 lb ft 110 degrees Coolant Crossover Pipe Bolt Front Coolant Crossover Pipe Bolt Side 10 Y 89 lb in Coolant Drain Plug 19 Y 14 lb ft Coolant Temperature Sensor 23 Y 17 lb ft Crankshaft Balancer Bolt Installation Pass Using the Old Bolt to Ensure the Balancer is Completely Installed 125 Y 92 lb ft Install a NEW Bolt After the Installation Pass and Tighten as Described in the First and es 125 Y 92 lb ft 130 degrees Crankshaft Main Bearing Cap Bolt/Stud

2 77 degrees Crankshaft Oil Deflector Nut 25 Y 18 lb ft Crankshaft Position Sensor Shield Nut 11 Y 98 lb in Crankshaft Position Sensor Stud 11 Y 98 lb in Cylinder Head Bolt 60 Y 44 lb ft 140 degrees Drive Belt Idler Pulley Bolt 13 mm 30 Y 22 lb ft Drive Belt Idler Pulley Bolt 15 mm Drive Belt Idler Pulley Bolt Upper Right and Lower Left Center Right 30 Y 22 lb ft Drive Belt Tensioner Bolt Engine Block Heater Engine Block Plug 60 Y 44 lb ft Engine Front Cover Bolt 25 Y 18 lb ft Engine Lift Bracket Bolt 70 Y 52 lb ft Engine Mount Bolts Engine Mount Bracket Bolts Convertible Except Convertible Bracket to Engine Block 90 Y 66 lb ft

3 Bracket to Oil Pan Engine Mount Bracket Lower Bolts Engine Mount Bracket Upper Bolts 90 Y 66 lb ft Engine Mount Nuts Engine Mount Strut Bolts Engine Mount Strut Bracket to Engine Bolts 25 Y 18 lb ft Engine Oil Pressure Switch 16 Y 12 lb ft Engine Wiring Harness Bracket Bolt 13 Y 115 lb in Engine Wiring Harness Ground Terminal Nut 25 Y 18 lb ft EVAP Purge Valve Bolt 12 Y 106 lb in Exhaust Crossover Heat Shield Bolts 10 Y 89 lb in Exhaust Crossover Pipe Nuts 25 Y 18 lb ft Exhaust Crossover Pipe Studs 25 Y 18 lb ft Exhaust Manifold Bolt 20 Y 15 lb ft Exhaust Manifold Heat Shield Bolt 10 Y 89 lb in Exhaust Manifold Lower Heat Shield Bolt 10 Y 89 lb in Flywheel Bolt Automatic Transmission 70 Y 52 lb ft Manual Transmission Manual Transmission 70 degrees Front Oil Gallery Plug 33 Y 24 lb ft Fuel Injector Rail Bolt 10 Y 89 lb in Fuel Injector Wiring Harness Electrical Connector Bracket Bolt 14 Y 124 lb in Generator Rear Brace Upper Nut 25 Y 18 lb ft

4 Generator Through Bolt Heated Oxygen Sensor 42 Y 31 lb ft Heater Inlet and Outlet Pipe Bolt 10 mm 10 Y 89 lb in Heater Inlet and Outlet Pipe Bolt/Nut 13 mm 25 Y 18 lb ft Heater Inlet Pipe Stud 35 Y 26 lb ft Ignition Coil Bracket Bolt/Nut/Stud 25 Y 18 lb ft Intake Manifold Cover Ball Stud 10 Y 89 lb in Knock Sensor 25 Y 18 lb ft Lower Intake Manifold Bolt Center 7 Y 62 lb in 16 Y 12 lb ft Lower Intake Manifold Bolt Corner 7 Y 62 lb in 25 Y 18 lb ft Oil Filter 30 Y 22 lb ft Oil Filter Adapter Bolt 25 Y 18 lb ft Oil Filter Adapter Heat Shield Nuts 25 Y 18 lb ft Oil Filter Fitting 39 Y 29 lb ft Oil Level Indicator Tube Bolt 25 Y 18 lb ft Oil Pan Bolt 25 Y 18 lb ft Oil Pan Drain Plug 25 Y 18 lb ft Oil Pan Side Bolt 50 degrees

5 Oil Pan Support Bracket Bolt Oil Pan to Transaxle Bolts Oil Pump Cover Bolt 10 Y 89 lb in Oil Pump Drive Gear Clamp Bolt 36 Y 27 lb ft Oil Pump Mounting Bolt 41 Y 30 lb ft Piston Oil Nozzle Bolt 10 Y 89 lb in Rear Oil Gallery Plug 3/8 inch 33 Y 24 lb ft Spark Plug 15 Y 11 lb ft Starter Motor to Engine Block Bolts 40 Y 30 lb ft Throttle Body Bolt/Nut 10 Y 89 lb in Throttle Body Stud 6 Y 53 lb in Timing Chain Tensioner Bolt 21 Y 15 lb ft Torque Converter to Flexplate Bolts 62 Y 46 lb ft Transaxle Brace Bolts 72 Y 53 lb ft Transaxle to Engine Bolts 75 Y 55 lb ft Transaxle to Oil Pan Bolts Transmission to Engine Bolts 75 Y 55 lb ft Transmission to Engine Brace Bolts Transmission Torque Converter Cover Bolts 7.5 Y 66 lb in Transmission Torque Converter to Flex Plate Bolts 62 Y 46 lb ft Upper Intake Manifold Bolt/Stud 25 Y 18 lb ft Valve Lifter Guide Bolt 10 Y 89 lb in Valve Lifter Oil Manifold Cover Plate Bolt 25 Y 18 lb ft Valve Rocker Arm Bolt 34 Y 25 lb ft Valve Rocker Arm Cover Bolt 10 Y 89 lb in Water Inlet Bolt/Stud 10 Y 89 lb in Water Pump Bolt 25 Y 18 lb ft

6 Water Pump Pulley Bolt 25 Y 18 lb ft

Lower Intake Manifold Replacement

Lower Intake Manifold Replacement Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the

More information

DISASSEMBLED VIEWS. Disassembled Views. Engine Covers and Component Assemblies (1 of 2) (LF1, LFW or LFX)

DISASSEMBLED VIEWS. Disassembled Views. Engine Covers and Component Assemblies (1 of 2) (LF1, LFW or LFX) 2012 Cadillac CTS Wagon AWD V6-3.0L Vehicle > Engine, Cooling and Exhaust > Engine > Locations > Components DISASSEMBLED VIEWS Disassembled Views Engine Covers and Component Assemblies (1 of 2) (LF1, LFW

More information

COMPONENT LOCATOR > DISASSEMBLED VIEWS

COMPONENT LOCATOR > DISASSEMBLED VIEWS Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine

More information

5.7L ENGINE PARTS BOOK. Not for. Reproduction

5.7L ENGINE PARTS BOOK. Not for. Reproduction 5.7L ENGINE PARTS BOOK Engine Model: Engine Family: PSI, Industrial Engine Spec N.: 39004120-39004248 Parts Book Revision: December, 2015 TABLE OF CONTENTS SECTION PAGE CYLINDER BLOCK... 3-5 CYLINDER HEAD...

More information

PARTIAL ENGINE ASSY (2ZZ GE)

PARTIAL ENGINE ASSY (2ZZ GE) COMPONENTS 14189 140R701 7.0 (71, 62 in. lbf) Cylinder Head Cover No. 2 19 (194, 14) Radiator Support Upper 19 (194, 14) Radiator Hose Inlet Cruise Control Actuator Assy 6.0 (61, 53 in. lbf) Radiator Assy

More information

Zoom and Print Options

Zoom and Print Options Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove

More information

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary. Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.

More information

TORQUE SPECIFICATIONS

TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS Application Ft. Lbs. (N.m) A/C Compressor Bracket Bolts Upper Vertical Bolt 16-21 (22-29) Horizontal Bolts 32-43 (43-58) A/C Compressor-To-Bracket Bolts 32-43

More information

7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).

7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L). 1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual

More information

PARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque

PARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque ENGINE MECHANICAL 1417 COMPONENTS 141FP01 Radiator Grille Front Bumper Cover Engine Under Cover RH Engine Under Cover LH A79361 962 1418 ENGINE MECHANICAL Heater Outlet Water Hose 7.0 (71, 62 in. lbf)

More information

PARTIAL ENGINE ASSY (2TR FE)

PARTIAL ENGINE ASSY (2TR FE) COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER

More information

Torque Guidelines (Z 22 SE)

Torque Guidelines (Z 22 SE) Page 1 of 14 Torque Guidelines (Z 22 SE) No. Designation Nm 1 Retaining bolts, coolant pump sprocket to coolant pump 2 Retaining bolts, balancer shaft timing chain guide rail to 3 Retaining bolts, balancer

More information

Disconnect negative battery cable and remove coolant bottle cap.

Disconnect negative battery cable and remove coolant bottle cap. 1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use

More information

2003 Taurus/Sable Workshop Manual

2003 Taurus/Sable Workshop Manual Page 1 of 24 SECTION 303-01A: Engine 3.0L (2V) ASSEMBLY 2003 Taurus/Sable Workshop Manual Engine Special Tool(s) Piston Ring Compressor 303- D032 (D81L-6002-C) Camshaft Bearing Set 303-017 (T65L-6250-A)

More information

Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC

Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC Torque Specifications for 2003 Hyundai Tiburon (GK) 2.7L DOHC Engine Mechanical System Camshaft sprocket bolt 90 ~ 110 900 ~ 1,100 65 ~ 80 Cylinder head cover bolt 8 ~ 10 80 ~ 100 5.8 ~ 7.2 Main bearing

More information

1 of 12 11/20/2016 9:32 PM

1 of 12 11/20/2016 9:32 PM 1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing

More information

5.7L V Chevrolet Camaro * PLEASE READ THIS FIRST * ENGINE IDENTIFICATION VEHICLE IDENTIFICATION NUMBER (VIN) ADJUSTMENTS

5.7L V Chevrolet Camaro * PLEASE READ THIS FIRST * ENGINE IDENTIFICATION VEHICLE IDENTIFICATION NUMBER (VIN) ADJUSTMENTS 5.7L V8 2001 Chevrolet Camaro 2000-01 ENGINES General Motors 5.7L V8 Chevrolet; Camaro Pontiac; Firebird * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE

More information

ENGINE REPAIR 966H (TAL/A6J/A6G) OPTIONS

ENGINE REPAIR 966H (TAL/A6J/A6G) OPTIONS 966H (TAL/A6J/A6G) OVERVIEW S OUT OF FRAME Cylinder Packs Main Bearings Standard Big End Bearing Standard Thrust Plates Fuel Filter Filter Assembly - Water Separator Cap-Pressure (Radiator) Engine Oil

More information

SECTION B Engine 5.0L (4V)

SECTION B Engine 5.0L (4V) 303-01B-i Engine 5.0L (4V) 303-01B-i SECTION 303-01B Engine 5.0L (4V) CONTENTS PAGE SPECIFICATIONS... 303-01B-2 303-01B-2 Engine 5.0L (4V) 303-01B-2 SPECIFICATIONS Material Motorcraft Metal Surface Prep

More information

ENGINE ASSEMBLY. COMPONENTS (Part 1)

ENGINE ASSEMBLY. COMPONENTS (Part 1) 1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS

More information

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) 1 of 15 8/7/2016 2:34 PM 2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E) Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Removal and Installation 2 of 15

More information

Intake Components 1117

Intake Components 1117 Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold

More information

SECTION A Engine 3.7L

SECTION A Engine 3.7L 303-01A-i Engine 3.7L 303-01A-i SECTION 303-01A Engine 3.7L CONTENTS PAGE SPECIFICATIONS... 303-01A-2 303-01A-2 Engine 3.7L 303-01A-2 SPECIFICATIONS Material Motorcraft High Performance Engine RTV Silicone

More information

2003 F-Super Duty /Excursion Workshop Manual

2003 F-Super Duty /Excursion Workshop Manual Page 1 of 16 SECTION 303-01C: Engine 7.3L Diesel DISASSEMBLY Procedure revision date: 05/21/2002 Engine Printable View (1761 KB) Special Tool(s) Cylinder Head Lifting Tool (D94T-6000-B) 303-D098 Damper

More information

1990 Buick Electra Limited

1990 Buick Electra Limited 4. To install remaining components, reverse removal procedure. Coat rocker arm bolts with GM Threadlock (12345493) prior to installation. Fig. 3: Cylinder Head Bolt Tightening Sequence FRONT CRANKSHAFT

More information

A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES. Signal (V) Ignition SW ON (Engine OFF) B B B

A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES. Signal (V) Ignition SW ON (Engine OFF) B B B 5. Specified Data A: ENGINE CONTROL MODULE (ECM) I/O SIGNAL FOR MT VEHICLES B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen heater Engine coolant temperature Signal

More information

Cylinder Head Replacement

Cylinder Head Replacement CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A

More information

Model 16CG5AMQ

Model 16CG5AMQ Model 16CG5AMQ 1 16 2 7 27 53 35 22 16 2 32 15 33 30 13 19 17 12 3 3 37 6 29 7 36 50 2 25 36 5 31 21 20 51 1 10 1 39 5 0 3 9 3 9 1 2 5 52 11 6 26 1 Model 16CG5AMQ Ref. Part Number Description 1 61-0035-0637

More information

REQUIRES SPECIAL TOOLS TO INSTALL. SEE REPAIR INSTRUCTION MANUAL. 411 718 38 3 1027 1 127 127 127A 1080 1081 1028 127 718A 127 718 44B 718A 2 44A 493 44 1069 112 718B 1019 LABEL KIT 1058 OWNER S MANUAL

More information

1991 Volkswagen Vanagon Syncro

1991 Volkswagen Vanagon Syncro corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at

More information

EM 92 2TR-FE ENGINE MECHANICAL ENGINE ASSEMBLY REMOVAL

EM 92 2TR-FE ENGINE MECHANICAL ENGINE ASSEMBLY REMOVAL 92 2TR-FE ENGINE MECHANICAL ENGINE ASSBLY ROVAL 1. ROVE HOOD SUB-ASSBLY 2. DISCHARGE FUEL SYST PRESSURE ( FU-1) 3. ROVE NO. 1 ENGINE UNDER COVER SUB- ASSBLY (for Pre Runner and 4WD Type) (a) Remove the

More information

5. Engine Control Module (ECM) I/O Signal S008526

5. Engine Control Module (ECM) I/O Signal S008526 5. Engine Control Module (ECM) I/O Signal S008526 A: ELECTRICAL SPECIFICATION S008526A08 1. MT VEHICLES S008526A0801 B2M2267A Crankshaft Camshaft Throttle Rear oxygen Front oxygen (A/F) heater Rear oxygen

More information

(DT20C ENGINE) JLR 3.0L 24V DOHC V6 TC Diesel TYPE TIGHTENING TORQUES. Rev. 2.0 OE

(DT20C ENGINE) JLR 3.0L 24V DOHC V6 TC Diesel TYPE TIGHTENING TORQUES. Rev. 2.0 OE (DT20C ENGINE) JLR 3.0L 24V DOHC V6 TC Diesel 1 TYPE TIGHTENING TORQUES 1. Cylinder head CAUTION : (*) Follow the tightening sequence. Reference Designation (1) bolts - Throttle butterfly housing Tightening

More information

SECTION C Engine 5.4L (4V)

SECTION C Engine 5.4L (4V) 303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 SPECIFICATIONS Material Motorcraft Metal Surface Prep

More information

REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM 14)

REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM 14) EM34 ENGINE MECHANICAL (2UZFE) EM11U02 REMOVAL 1. DRAIN ENGINE COOLANT 2. REMOVE THROTTLE BODY COVER 3. DISCONNECT TIMING BELT FROM CAMSHAFT TIM- ING PULLEYS (See page EM14) A02844 Be careful not to drop

More information

M-6007-A50NA Engine Specifications and Owner's Manual

M-6007-A50NA Engine Specifications and Owner's Manual M-6007-A50NA Engine Specifications and Owner's Manual Fordracingparts.com Techline 1-800-367-3788 Page 1 of 11 IS-1850-0377 Please visit www.fordracingparts.com for the most current instruction information.!!!

More information

DESCRIPTION AND OPERATION

DESCRIPTION AND OPERATION 303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589

More information

5. Engine Control Module (ECM) I/O Signal

5. Engine Control Module (ECM) I/O Signal 5. A: ELECTRICAL SPECIFICATION B134 B135 B136 B137 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 19 18 34 33 32 31 30 29 28 19 18 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 35 34 33 32 31

More information

EM 97 2TR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSTALLATION

EM 97 2TR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSTALLATION 2TR-FE ENGINE MECHANICAL ENGINE ASSBLY 97 G038557E01 INSTALLATION 1. INSTALL ENGINE OIL PRESSURE SWITCH ASSBLY ( LU-1) 2. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH (a) Install the engine mounting

More information

REMOVAL. 10. REMOVE FRONT SUSPENSION MEMBER BRACE Remove the 8 bolts and brace.

REMOVAL. 10. REMOVE FRONT SUSPENSION MEMBER BRACE Remove the 8 bolts and brace. EM64 ENGINE MECHANICAL (2JZGE) EM1S801 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DRAIN ENGINE OIL 4. REMOVE ENGINE COVER Remove the 4 nuts and engine cover. 5. REMOVE AIR CLEANER

More information

Air Intake/Filtration

Air Intake/Filtration Air Intake/Filtration Air Intake/Filtration Ref # Part Description Qty 25 048 -S CLEANER, AIR-CANISTER (includes 2-8) 2 25 096 06-S COVER ASSMBLY,AIR CLEANER (includes 3,4) 3 24 462 07-S VALVE, DUST EJECTOR

More information

Page 1 of 9 SECTION 303-01B: Engine 2.0L SPI 2002 Focus Workshop Manual ASSEMBLY Procedure revision date: 12/14/2000 Engine Special Tool(s) Crankshaft Rear Seal Pilot 303-329 (T88P-6701-B2) Crankshaft

More information

365-SUB Engine : Engine Assembly 365-SUB [1/1] Page 1 of 5

365-SUB Engine : Engine Assembly 365-SUB [1/1] Page 1 of 5 Page 1 of 5 1 951-11012 Bolt 2 951-11054 Valve Cover 2 951-11054 1 Valve Cover 3 731-07059 Breather Hose 4 726-04101 Hose Clamp 6 N/A 1 Intake Valve Spring Seat 7 751-11124 Pivot Locking Nut 7 751-11124

More information

REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide.

REMOVAL. 5. REMOVE OIL DIPSTICK GUIDE (a) Remove the bolt, dipstick guide and engine wire bracket. (b) Remove the O ring from the dipstick guide. EM34 ENGINE MECHANICAL (2RZFE, 3RZFE) P23426 EM1MY01 REMOVAL 1. DRAIN ENGINE COOLANT 2. DISCONNECT THESE CABLES: (a) Disconnect the accelerator cable from the throttle body. A/T: Disconnect the throttle

More information

Intake Manifold Replacement

Intake Manifold Replacement Page 1 of 13 Your Current Vehicle: 2008 Cadillac STS Intake Manifold Replacement Intake Manifold Replacement Removal Procedure 1. Turn the ignition OFF. 2. Remove the fuel injector sight shield. Refer

More information

CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT

CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT REPLACEMENT N0. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE ). REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE ). REMOVE STARTER ASSY (SEE PAGE 99). REMOVE AUTOMATIC TRANSAXLE ASSY (SEE PAGE

More information

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION

More information

ILLUSTRATED PARTS BOOK Walk Behind Mower MODEL: SM2010

ILLUSTRATED PARTS BOOK Walk Behind Mower MODEL: SM2010 ILLUSTRATED PARTS BOOK Walk Behind Mower MODEL: SM2010 Table of Contents Top Level Assembly...3 Engine Top Level Assembly..4 Handle Assembly 5 Frame Assembly.6 Blade Assembly...7 Wheel Assembly.8 Warning

More information

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly

Audi > B4 > Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Audi > B4 > 1993 1995 2.8 Liter V6 2V Engine Mechanical, Engine Code(s): AAH, AFC 10 Engine Assembly Removing The engine is removed from above, after being separated from the transmission. Note: All tie

More information

CUMMINS ENGINE ISX15 ISX CM2250 Service Workshop Manual

CUMMINS ENGINE ISX15 ISX CM2250 Service Workshop Manual Instant Manual Download CUMMINS ENGINE ISX15 ISX CM2250 Service Workshop Manual Download Here CUMMINS ENGINE ISX15 Service Workshop Repair Shop Manual PLEASE NOTE: YOU NEED TO BE CONNECTED TO THE INTERNET

More information

1998 Saab 900 SE ENGINES Saab 2.0L & 2.3L 4-Cylinder

1998 Saab 900 SE ENGINES Saab 2.0L & 2.3L 4-Cylinder Removal & Installation See VALVE SPRINGS under CYLINDER HEAD under OVERHAUL. CAMSHAFT Removal 1. Rotate crankshaft until "0" mark on flywheel aligns with timing mark on flywheel cover. Remove inspection

More information

Pubert engine R100 Part list Moteur Pubert R100 Pièces détachées

Pubert engine R100 Part list Moteur Pubert R100 Pièces détachées Pubert engine R100 Part list Moteur Pubert R100 Pièces détachées Ref part list :0330091002 FIG.1 HEAD SUBASSEMBLY, CYLINDER / PLUG,SPARK (E04) E04-1 12140-Z510110-0000 0001150103 HEAD SUBASSEMBLY, CYLINDER

More information

2011 Mercury Grand Marquis LS

2011 Mercury Grand Marquis LS Fig. 6: Locating Intake Manifold Crash Bracket With Tie Strap 24. Remove the intake manifold crash bracket bolt. 25. Disconnect the fuel rail pressure and temperature sensor vacuum and electrical connectors.

More information

E70PL4EEC 1999 : CAMSHAFT [1/23] Page 1 of 49

E70PL4EEC 1999 : CAMSHAFT [1/23] Page 1 of 49 E70PL4EEC 1999 : CAMSHAFT [1/23] Page 1 of 49 E70PL4EEC 1999 : CAMSHAFT [1/23] 1 5030657 1 CAMSHAFT 2 5030658 1 PLATE, Camshaft thrust 3 5030549 1 SEAL, Camshaft 4 5030989 2 BOLT, Plate 5 5030663 8 ARM,

More information

RYOBI Pressure Washer Manufacturing No Item No. RY Replacement Parts List

RYOBI Pressure Washer Manufacturing No Item No. RY Replacement Parts List RYOBI Pressure Washer Manufacturing No. 090079399 Item No. RY8000 Replacement Parts List TECHTRONIC INDUSTRIES POWER EQUIPMENT 428 Pearman Dairy Road, Anderson, SC 62 USA -800-860-400 www.ryobitools.com

More information

ENGINE MECHANICAL <3.0L ENGINE>

ENGINE MECHANICAL <3.0L ENGINE> 11C-1 GROUP 11C ENGINE MECHANICAL CONTENTS GENERAL DESCRIPTION......... 11C-2 ENGINE DIAGNOSIS............. 11C-3 SPECIAL TOOLS................ 11C-4 ON-VEHICLE SERVICE........... 11C-6 DRIVE

More information

DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage.

DISASSEMBLY. Engine. CAUTION: Remove the cylinder heads before removing the crankshaft. Failure to do so can result in engine damage. 303-01A-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Vibration Damper 303-101 (T74P-3616-A) Special Tool(s) Crankshaft Socket 303-674 303-01A-1 Remover, Crankshaft Vibration Damper 303-773

More information

GROUP 11C 11C-1 CONTENTS GENERAL DESCRIPTION... 11C-2 ENGINE DIAGNOSIS... 11C-2 CRANKSHAFT FRONT OIL SEAL... 11C-30 SPECIAL TOOLS...

GROUP 11C 11C-1 CONTENTS GENERAL DESCRIPTION... 11C-2 ENGINE DIAGNOSIS... 11C-2 CRANKSHAFT FRONT OIL SEAL... 11C-30 SPECIAL TOOLS... 11C-1 GROUP 11C CONTENTS GENERAL DESCRIPTION 11C-2 ENGINE DIAGNOSIS 11C-2 SPECIAL TOOLS 11C-3 ON VEHICLE SERVICE 11C-5 DRIVE BELT TENSION CHECK AND ADJUSTMENT 11C-5 IGNITION TIMING CHECK 11C-5 IDLE MIXTURE

More information

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components. 4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,

More information

WE JUST MADE YOUR DRIVE A LITTLE MORE RELAXING. THE ENHANCED COVERAGE FOR YOUR BMW CPO VEHICLE.

WE JUST MADE YOUR DRIVE A LITTLE MORE RELAXING. THE ENHANCED COVERAGE FOR YOUR BMW CPO VEHICLE. WE JUST MADE YOUR DRIVE A LITTLE MORE RELAXING. Introducing THE CERTIFIED PRE-OWNED (CPO) WRAP, THE ENHANCED COVERAGE FOR YOUR BMW CPO VEHICLE. When you purchase a Certified Pre-Owned BMW, you look forward

More information

Chainsaw Emak S.p.A.

Chainsaw Emak S.p.A. Chainsaw - Engine Meccanografico RE 005145 C/C Postale 11178423 Partita IVA 00130010358 Codice Fiscale 00130010358 1 / 15 Meccanografico RE 005145 C/C Postale 11178423 Partita IVA 00130010358 Codice Fiscale

More information

13A2693G190 LT-165 (2003) Page 1 of 31 Carburetor

13A2693G190 LT-165 (2003) Page 1 of 31 Carburetor 13A2693G190 LT-165 (2003) Page 1 of 31 Carburetor 13A2693G190 LT-165 (2003) Page 2 of 31 Carburetor TC-640330 1 S Carburetor (Incl 184 of Engine Parts Lists) 1 TC-640035 1 Throttle Shaft & Lever Assembly

More information

Page 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description

More information

2. Remove the intake manifold cover. Refer to Intake Manifold Cover Replacement.

2. Remove the intake manifold cover. Refer to Intake Manifold Cover Replacement. VALVE COVER GASKET Valve Rocker Arm Cover Replacement - Left Side Removal Procedure 1. Partially drain the cooling system. Refer to Cooling System Draining and Filling (LZE, LZ4, LZG, 9C1, 9C3, GE47716

More information

1.6L 4-CYL - VIN [E]

1.6L 4-CYL - VIN [E] 1.6L 4-CYL - VIN [E] 1993 Nissan Sentra 1993 NISSAN ENGINES 1.6L 4-Cylinder NX, Sentra * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES

More information

STARTER COMPONENTS FOR REMOVAL AND INSTALLATION

STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Removal STARTER COMPONENTS FOR REMOVAL AND INSTALLATION Starter Components For Removal And Installation REMOVAL OF STARTER 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started

More information

WSS- M97B51-A1 WSS- M2C930-A. 5.7L (6 qt) with filter WSE- M4G323-A4

WSS- M97B51-A1 WSS- M2C930-A. 5.7L (6 qt) with filter WSE- M4G323-A4 SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual SPECIFICATIONS Procedure revision date: 01/22/2009 Material Item Specification Fill Capacity Gasket Maker TA-16 WSK- M2G348-A5 Motorcraft

More information

5. Engine Control Module (ECM) I/O Signal

5. Engine Control Module (ECM) I/O Signal 5. Engine Control Module (ECM) I/O Signal A: ELECTRICAL SPECIFICATION B134 B135 B136 B137 17 16 15 14 13 12 11 10 9 8 27 26 25 24 23 22 21 20 19 18 34 33 32 31 30 29 28 19 18 17 16 15 14 13 12 11 10 9

More information

Alternator bracket Box 1. Alternator engine plate Box 1. Alternator pulley Box 1. Alternator spacer (1.760") Box 1

Alternator bracket Box 1. Alternator engine plate Box 1. Alternator pulley Box 1. Alternator spacer (1.760) Box 1 NASCAR SPEC ENGINE KIT PACKING LIST Part + Required Fasteners Quantity RYRE Part # Box # Inside Crate Alternator 1 100001 Individual Box 3/8-24 x 5.00 Hex 1 7/16-14 x 5.50 Hex 1 3/8-24 Flanger Nut 1 3/8

More information

MITSIBUSHI FTO NUT,BOLT AND TORQUE GUIDE

MITSIBUSHI FTO NUT,BOLT AND TORQUE GUIDE MITSIBUSHI FTO NUT,BOLT AND TORQUE GUIDE All information below has been obtained from the official Mitsubishi fto workshop manual, and I hold no liability for any incorrect information. Heads marked 4

More information

Cummins engine Signature ISX QSX15 Service Workshop Shop Repair Manual - PDF Service Manual

Cummins engine Signature ISX QSX15 Service Workshop Shop Repair Manual - PDF Service Manual Cummins engine Signature ISX QSX15 Service Workshop Shop Repair Manual - PDF Service Manual DOWNLOAD HERE "Cummins engine Signature ISX QSX15 Service Workshop Shop Repair Manual - PDF Service Manual Signature

More information

CYLINDER HEAD (for Bank 2 4WD and Pre-Runner)

CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) 144 1GR-FE ENGINE MECHANICAL CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) ENGINE 1GR-FE ENGINE MECHANICAL COMPONENTS 88 (897, 65) x4 88 (897, 65) x4 NO. 1

More information

Illustrated Parts List MODEL Reproduction. Not for. 48,000 Watt Home Generator System

Illustrated Parts List MODEL Reproduction. Not for. 48,000 Watt Home Generator System Illustrated Parts List MODEL 076035-0 48,000 Watt Home Generator System Rev. A 4/14/2011 Table Of Contents PRODUCT COMPONENTS Main Unit... 4 Alternator... 6 Control Panel... 7 Enclosure... 8 Engine -

More information

Service Parts. Engine. Engine Model: KG L. Generator Models: 24/30RCL 38RCLB CCL. TP /18b

Service Parts. Engine. Engine Model: KG L. Generator Models: 24/30RCL 38RCLB CCL. TP /18b Service Parts Engine Engine Model: KG0.L Generator Models: /0RCL 8RCLB 5--6CCL TP-690 9/8b Table of Contents Description Page Introduction... Number System Significance... Illustrations... How to Find

More information

DISASSEMBLY Procedure revision date: 11/22/2001

DISASSEMBLY Procedure revision date: 11/22/2001 Page 1 of 31 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:06 PM To: 'Evan Groenke' Subject: 2.5 L Engine Disassembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop

More information

FUEL PUMP CAMSHAFT TIMING CHECK

FUEL PUMP CAMSHAFT TIMING CHECK PUBLISHED: 26-FEB-2018 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING CHECK (G1473740) GENERAL PROCEDURES 19.90.16 HIGH PRESSURE FUEL TIMING CHECK 5000 CC,

More information

ILLUSTRATED PARTS LIST MS330ECH PUMP/ENGINE PACKAGE. MS330ECH PUMP/ENGINE PACKAGE PART # REV12/01 Maruyama. E x t r a o r d i n a r y.

ILLUSTRATED PARTS LIST MS330ECH PUMP/ENGINE PACKAGE. MS330ECH PUMP/ENGINE PACKAGE PART # REV12/01 Maruyama. E x t r a o r d i n a r y. MARUYAMA ILLUSTRATED PARTS LIST PUMP/ENGINE PACKAGE PUMP/ENGINE PACKAGE PART #4540 REV1/01 Maruyama. E x t r a o r d i n a r y. ILLUSTRATED PARTS LIST MAIN BODY 7 5 1 1 0 9 4 17 11 15 14 3 1 1 19 5 1 9

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before

More information

1. Remove the timing belt upper front cover. Refer to Timing Belt Upper Front Cover Removal.

1. Remove the timing belt upper front cover. Refer to Timing Belt Upper Front Cover Removal. 2013 Sonic Applies to: 1.8L (LUW, LWE) Report a problem with this article Special Tools EN-652 Flywheel Holder EN-6333 Locking Pin EN-6340 Locking Tool EN-6628-A Locking Tool EN-45059 Torque Angle Sensor

More information

Ref Partnumber Description GXV610K1 Serial Numbers ZE3-W01ZB STARTER ASSY., RECOIL *NH1 * ZE3-W01ZP STARTER ASSY.

Ref Partnumber Description GXV610K1 Serial Numbers ZE3-W01ZB STARTER ASSY., RECOIL *NH1 * ZE3-W01ZP STARTER ASSY. GXV610K1(QWA/A) E-11 RECOIL STARTER 001 28400-ZE3-W01ZB STARTER ASSY., RECOIL *NH1 * 1 001 28400-ZE3-W01ZP STARTER ASSY., RECOIL *R280 * 1 2009863 002 28410-ZE3-W01ZB CASE COMP., RECOIL STARTER *NH1 *

More information

Illustrated Parts List

Illustrated Parts List FORM MS 56 08/11/2004 REPLACES FORM MS 56 11/14/2002 FILE IN SECT. 2 OF SERVICE MANUAL 312700 Illustrated Parts List Model Series 312700 TYPE NUMBERS 0101 through 01. TABLE OF CONTENTS Air Cleaner.........................

More information

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.

1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting

More information

Cylinder Head Removal

Cylinder Head Removal 2006 Odyssey Cylinder Head Removal Report a problem with this article NOTE: Use fender covers to avoid damaging painted surfaces. To avoid damaging the wires and terminals, unplug the wiring connectors

More information

7-8 CHEVROLET AND GMC BLAZER JIMMY S10 SONOMA _U07.qxd 8/30/05 3:01 PM Page 8 BVC GMC CARS JCK/MJS/KJE 8/22/ S10P-C07

7-8 CHEVROLET AND GMC BLAZER JIMMY S10 SONOMA _U07.qxd 8/30/05 3:01 PM Page 8 BVC GMC CARS JCK/MJS/KJE 8/22/ S10P-C07 26770_U07.qxd 8/30/05 3:01 PM Page 8 7-8 06025-S10P-C07 06025-S10P-C08 26770_U07.qxd 8/30/05 3:01 PM Page 9 7-9 06025-S10P-C09 26770_U07.qxd 8/30/05 3:01 PM Page 10 7-10 06025-S10P-C10 26770_U07.qxd 8/30/05

More information

Illustrated Parts List

Illustrated Parts List FORM MS 54 08/11/2004 REPLACES FORM MS 54 11/14/2002 FILE IN SECT. 2 OF SERVICE MANUAL 311700 Illustrated Parts List Model Series 311700 TYPE NUMBERS 0005 through 0209. TABLE OF CONTENTS Air Cleaner.........................

More information

Craftsman Snow Thrower Model PARTS LIST

Craftsman Snow Thrower Model PARTS LIST Craftsman Snow Thrower Model 24.88955 11 13 3 26 24 9 1 18 54 6 25 15 20 23 16 5 14 1 55 9 4 4 28 8 30 2 5 56 35 36 46 3 39 50 53 43 38 48 52 42 51 41 40 49 4 44 31 45 31 21 29 34 9 19 10 32 22 26 Craftsman

More information

Engine 3.5L 2010 Edge, MKX. SPECIFICATIONS Procedure revision date: 08/26/2013. Specification. Item Specification Fill Capacity

Engine 3.5L 2010 Edge, MKX. SPECIFICATIONS Procedure revision date: 08/26/2013. Specification. Item Specification Fill Capacity 2010 Edge Report a prolem with this article 303-01 Engine 3.5L 2010 Edge, MKX SPECIFICATIONS Procedure revision date: 08/26/2013 s Material Fill Capacity Motorcraft High Performance Engine RTV Silicone

More information

LINCOLN. Continental 1

LINCOLN. Continental 1 3154_U01.qxd 8/1/03 7:28 AM Page 1 Continental 1 BRAKES...1-27 DRIVE TRAIN...1-21 ENGINE REPAIR...1-7 FUEL SYSTEM...1-20 PRECAUTIONS...1-7 SPECIFICATION CHARTS...1-2 STEERING AND SUSPENSION...1-22 A Air

More information

UT cc Chain Saw Page 1 of 9 Figure A

UT cc Chain Saw Page 1 of 9 Figure A UT10519 46cc Chain Saw Page 1 of 9 Figure A UT10519 46cc Chain Saw Page 2 of 9 Figure A 1 700106001 1 Heat Reflector Tape 2 671087001 4 Spacer Insert 3 570226001 1 S Oil Outlet Grommet 4 660503002 1 Guide

More information

Water Pump Mfg. No Item No. UT40520 Replacement Parts List

Water Pump Mfg. No Item No. UT40520 Replacement Parts List Water Pump Mfg. No. 099858001 Item No. UT40520 Replacement Parts List 990000709 6-4-15 (Rev:01) HOMELITE CONSUMER PRODUCTS, INC. 1428 Pearman Dairy Road, Anderson, SC 29625 Phone 1-800-242-4672 www.homelite.com

More information

Illustrated Parts List to

Illustrated Parts List to Illustrated Parts List Model Series 176400 to 176499 TYPE NUMBERS 0035, 0049, 0050, 0101, 0103, 0113, 0114, 0115, 0116. FORM MS 0419 9/97 REPLACES FORM MS 0419 5/97 FILE IN SECT. 2 OF SERVICE MANUAL 176400

More information

MARINE ILLUSTRATED PARTS MANUAL MODEL MP6.0L

MARINE ILLUSTRATED PARTS MANUAL MODEL MP6.0L MARINE ILLUSTRATED PARTS MANUAL MODEL MP6.0L L510014 12/02 This Page Was Intentially Left Blank MODEL MP6.0L PARTS MANUAL - 1 Contents: Symbols... 2 Maintenance Item Part Numbers... 3 Cylinder Block Assembly

More information

H8190 Pump Parts Breakdown

H8190 Pump Parts Breakdown H8190 Pump Parts Breakdown -30- H8189/H8190 Gasoline Pressure Washer H8190 Pump Parts List 1 PH8189001 CRANK CASE COVER BOLT 51 PH8189051 VALVE JACKET INNER GASKET 2 PH8189002 OIL DRAIN PLUG 52 PH8189052

More information

TM 500 G2R PRO FIG.1 HEAD SUBASSEMBLY, CYLINDER / PLUG,SPARK (E01)

TM 500 G2R PRO FIG.1 HEAD SUBASSEMBLY, CYLINDER / PLUG,SPARK (E01) TM 500 G2R PRO TM 500 G2R PRO FIG.1 HEAD SUBASSEMBLY, CYLINDER / PLUG,SPARK (E01) E01-4 12131-Z140120-0000 GASKET, CYLINDER HEAD 1 1 E01-5 12410-Z300120-0000 COVER SUBASSEMBLY, CYLINDER HEAD 1 1 E01-6

More information

ENGINE GENERAL ENGINE GENERAL GENERAL OVERVIEW AND OPERATION PROCESS 1. STRUCTURE...

ENGINE GENERAL ENGINE GENERAL GENERAL OVERVIEW AND OPERATION PROCESS 1. STRUCTURE... GENERAL 1. STRUCTURE... 3 OVERVIEW AND OPERATION PROCESS 1. ENGINE CONTROLS COMPONENTS... 2. INTAKE SYSTEM COMPONENTS... 3. EXHAUST SYSTEM COMPONENTS... 4. LUBRICATION SYSTEM COMPONENTS... 5. COOLING SYSTEM

More information

GXV620K1(QYF) E-12-1 FAN COVER (2)

GXV620K1(QYF) E-12-1 FAN COVER (2) GXV620K1(QYF) E-12-1 FAN COVER (2) 001 16715-ZJ1-840 COVER, FUEL PUMP 1 003 19611-ZJ1-850ZA COVER, FAN (RECOIL STARTER) *NH1 * 1 003 19611-ZJ1-850ZB COVER, FAN (RECOIL STARTER) *R8 * 1 2005207 003 19611-ZJ1-850ZC

More information

PARTS MANUAL SUPPORTED BY HUSTLER TURF EQUIPMENT AND EXCEL INDUSTRIES, INC.

PARTS MANUAL SUPPORTED BY HUSTLER TURF EQUIPMENT AND EXCEL INDUSTRIES, INC. SHIBAURA DIESEL ENGINE MODEL: N843 and N843L PARTS MANUAL SUPPORTED BY HUSTLER TURF EQUIPMENT AND EXCEL INDUSTRIES, INC. Table of Contents Chapter 1 General Information....................................

More information

ENGINE MECHANICAL <3.0L>

ENGINE MECHANICAL <3.0L> 11C-1 GROUP 11C ENGINE MECHANICAL CONTENTS GENERAL DESCRIPTION......... 11C-2 ENGINE DIAGNOSIS............. 11C-2 SPECIAL TOOLS................ 11C-3 ON VEHICLE SERVICE........... 11C-5 DRIVE BELT

More information

ENGINE ASSEMBLY COMPONENTS EM 170 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY V-BANK COVER VACUUM HOSE AIR CLEANER ASSEMBLY NO. 2 VENTILATION HOSE

ENGINE ASSEMBLY COMPONENTS EM 170 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY V-BANK COVER VACUUM HOSE AIR CLEANER ASSEMBLY NO. 2 VENTILATION HOSE 170 ENGINE 1GR-FE MECHANICAL COMPONENTS 1GR-FE ENGINE MECHANICAL ENGINE 7.5 (76, 66 in.*lbf) V-BANK COVER 8.0 (82, 71 in.*lbf) 8.0 (82, 71 in.*lbf) VACUUM HOSE AIR CLEANER NO. 2 VENTILATION HOSE MASS AIR

More information

Illustrated Parts List. Model Series. TYPE NUMBERS 0035 through TABLE OF CONTENTS

Illustrated Parts List. Model Series. TYPE NUMBERS 0035 through TABLE OF CONTENTS Illustrated Parts List Model Series TYPE NUMBERS 0035 through 0563. TABLE OF CONTENTS FORM MS--6359--08/04/2009 REPLACES FORM MS--6359--10/07/2008 FILE IN SECT. 2 OF SERVICE MANUAL Air Cleaner... 5 Alternator...

More information