1998 Contour/Mystique Workshop Manual
|
|
- Marlene Waters
- 5 years ago
- Views:
Transcription
1 SECTION 30-01: Automatic Transmission/Transaxle 1998 Contour/Mystique Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 09/14/2001 Main Controls Special Tool(s) Aligner, Selector Shaft 30-S290 (T94P 000 H) TRS Sensor Alignment Tool (T9L 0010 A) Material MERCON Multi-purpose automatic transmission fluid MERCON XT-2-QDX Removal 1. Disconnect the battery ground cable. 2. Remove the battery tray. For additional information, refer to Section Vehicles with air conditioning 3. CAUTION: Do not place excessive pressure on tubes/hoses (A/C) and fittings when disconnecting and reconnecting A/C components. Excessive pressure may cause component damage and A/C system leaks. NOTE: On some vehicles, it may be necessary to disconnect and position the A/C suction accumulator out of the way to allow enough room for main control cover removal. Remove the suction accumulator bracket and position the suction accumulator to one side. Loosen the suction accumulator canister holding screw, and remove the suction accumulator from the bracket. 4. Disconnect the transaxle wiring harness electrical connector. 1. Remove the ground cable, if fitted. 2. Remove the solenoid body electrical connector. 3. Remove the transmission range (TR) sensor electrical connector. 4. Remove the wiring harness retaining clip. 5. Disconnect the transmission shift cable and bracket. 1. Remove the bracket bolts. 2. Remove the cable. 6. NOTE: Position a suitable drain pan under the main control cover. Disconnect the transaxle cooler inlet line.
2 . NOTE: Remove the bolts in the indicated sequence. Remove the main control cover. Open clamp and disconnect the main control cover vent tube. Remove the main control bolts and main control cover. 8. Remove the main control cover gasket. 9. NOTE: Remove the bolts in the indicated sequence. Remove the main control valve body bolts. 10. NOTE: Do not damage the manual valve. Lift the main control valve body while disconnecting the manual valve link.
3 11. Remove the solenoid body harness connector. 1. Depress the retaining tabs. 2. Push the solenoid valve body electrical connector down through the transaxle case. 12. Make sure the manual valve control lever does not fall out while removing from the vehicle. Installation 1. Install the manual valve. 2. NOTE: Inspect solenoid valve body harness connector O-ring seal and install new as necessary before installing solenoid valve body harness connector in transaxle case. Push the solenoid valve body harness connector up through the transaxle case. 3. Connect the manual valve link to the manual valve. 4. NOTE: Install the bolts in the indicated sequence. Position the main control valve body and install the mounting bolts.
4 5. Loosen the nut on the ball stud for the manual valve detent lever actuating rod assembly. 6. Remove the manual control lever bolt.. Using the special tool and pin, align the shifter shaft. 8. Move the manual valve detent lever assembly to the ``D" position. 9. Tighten the nut on the ball. Remove the shifter pin from the special tool. 10. Rotate the special tool until the socket can be fitted on nut. Tighten the detent nut. Rotate back to the ``D" position and check the adjustment.
5 11. Using the special tool, check the manual control lever assembly settings. 12. Install the manual control lever. 1. Position the manual control lever. 2. Tighten the bolt. 13. Install and rotate the manual valve detent lever assembly to the NEUTRAL position. 1. Low 1 2. Low 2 3. Drive 4. Neutral 5. Reverse 6. Park 14. Connect the shift cable to the control lever. 1. Install the shift cable. 2. Install the bolts. 15. Install new gasket on the main control cover before positioning. 16. NOTE: Tighten the bolts in the indicated sequence. Install the main control cover. Connect the main control cover vent tube and close clamp. Position main control cover and tighten bolts.
6 1. NOTE: Remove the drain pan. Connect the transaxle cooler inlet line. 18. NOTE: Do not tighten the TR sensor bolts. Install the transmission range (TR) sensor and install the bolts loosely. 19. Tighten the TR sensor bolts. For additional information, refer to Transmission Range (TR) Sensor in this section. 20. Connect the transaxle harness electrical connector. 1. Install the ground cable. 2. Install the solenoid body electrical connector. 3. Install the TR sensor electrical connector. 4. Install the wiring harness clip. Vehicles with air conditioning 21. CAUTION: Do not place excessive pressure on tubes/hoses (A/C) and fittings when disconnecting and reconnecting A/C components. Excessive pressure may cause component damage and A/C system leaks. NOTE: On some vehicles, it may be necessary to disconnect and position the suction accumulator out of the way to allow enough room for main control cover removal. Position the suction accumulator and install the screws.
7 22. Install the battery tray. For additional information, refer to Section NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 160 km (100 miles) or more to relearn the strategy. Connect the battery ground cable. 24. Check the transmission fluid, add as necessary use Motorcraft MERCON multi-purpose transmission fluid or equivalent meeting MERCON specification. 25. Start the engine and move the transaxle range selector lever through all gear positions. Refill as necessary.
IN-VEHICLE REPAIR. Main Control Valve Body. Removal. 6. Disconnect the transaxle wiring harness electrical connector and TR sensor connector.
307-01-1 Automatic Transaxle/Transmission 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Material Item Thread Sealant with PTFE TA-24 Motorcraft MERCON Multi-Purpose (ATF) Transmission Fluid XT-2-QDX
More informationMAIN CONTROL VALVE BODY. Removal 1. Disconnect the battery cables. 2. Remove the battery and tray.
1 of 17 MAIN CONTROL VALVE BODY Removal 1. Disconnect the battery cables. 2. Remove the battery and tray. 3. Disconnect the breather tube and mass air flow (MAF) / intake air temperature (IAT) sensor.
More informationDisconnect the breather tube and mass air flow (MAF) /intake air temperature (IAT) sensor.
1 of 19 10/1/2011 11:11 AM oval 1. 2. Disconnect the battery cables. Remove the battery and tray. 3. Disconnect the breather tube and mass air flow (MAF) /intake air temperature (IAT) sensor. 4. Remove
More information1 of 14 11/19/ :45 AM
1 of 14 11/19/2016 11:45 AM 6F35 Digital Transmission Range (TR) Sensor Removal All vehicles 1. With the vehicle in NEUTRAL, position it on a hoist. 3.0L engine 2. Remove the Air Cleaner (ACL) outlet pipe.
More informationAutomatic Transmission 5R44E and 5R55E
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Special Tool(s) Aligner, Valve Body 307-333 (T95L-70010-B) Aligner, Valve Body 307-334 (T95L-70010-C)
More informationIN-VEHICLE REPAIR. Output Shaft Speed (OSS) Sensor. Removal
307-01-1 Automatic Transaxle/Transmission 6F50 307-01-1 IN-VEHICLE REPAIR Output Shaft Speed (OSS) Sensor Material Item MERCON V Automatic Transmission Fluid XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada)
More informationPage 1 of 7 Section 07-01A: Transmission, Automatic, E4OD IN-VEHICLE SERVICE 1993 Bronco/Econoline/F-Series Workshop Manual Valve Bodies and Intermediate Band Servo NOTE: If a transmission has been disassembled
More information1998 Escort/Tracer Workshop Manual
Page 1 of 11 SECTION 307-01: Automatic Transaxle/Transmission 1998 Escort/Tracer Workshop Manual DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIES Procedure revision date: 03/05/1998 Main Control Valve Body Assembly
More information2007 Explorer/Mountaineer/Explorer Sport Trac Workshop Manual MERCON V
2007 Explorer SECTION 307-01A: Automatic Transaxle/Transmission 5R55S 2007 Explorer/Mountaineer/Explorer Sport Trac Workshop Manual Report a problem with this article IN-VEHICLE REPAIR Procedure revision
More information2002 F-Super Duty /Excursion Workshop Manual
Page 1 of 25 SECTION 307-01: Automatic Transaxle/Transmission 2002 F-Super Duty 250-550/Excursion Workshop Manual ASSEMBLY Procedure revision date: 05/23/2001 Transmission Special Tool(s) Remover, O-Ring
More informationAssembly. NOTE: Before beginning assembly, perform/inspect the following:
Page 1 of 31 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 1997 Ford Truck F 150 2WD Pickup V6-4.2L VIN 2
More information2003 E-Series Workshop Manual
Page 1 of 20 SECTION 307-01B: Automatic Transmission 4R70W 2003 E-Series Workshop Manual ASSEMBLY Procedure revision date: 04/27/2006 Transmission Printable View (1828 KB) Special Tool(s) Dial Indicator
More informationPage 1 of 6 Section 03-01B: Engine, 7.5L MFI Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 05/17/2000 Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Damper Remover
More information1 of 1 7/1/17, 2:02 PM. Air Cleaner Assembly Replacement ALLDATA, LLC. All Rights Reserved. (Version )
Air Cleaner Housing Service and Repair, Removal and Replacement: Ai... http://repair.alldata.com/alldata/article/display.action?componentid=367... 1 of 1 7/1/17, 2:02 PM Air Cleaner Assembly Replacement
More informationTransmission Diesel Engines
Page 1 of 17 SECTION 307-01B: Automatic Transaxle/Transmission TorqShift 6 2011 F-250, 350, 450, 550 Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 11/12/2010 Transmission
More information2002 F-150 Workshop Manual
Page 1 of 8 SECTION 307-01B: Automatic Transmission 4R70W 2002 F-150 Workshop Manual REMOVAL Procedure revision date: 04/02/2003 Transmission Special Tool(s) Retainer, Torque Converter 307-346 (T97T-7902-A)
More informationSECTION Automatic Transaxle/Transmission 6R80
307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE IN-VEHICLE REPAIR Main Control... 307-01-2 307-01-2 Automatic Transaxle/Transmission
More information1999 Explorer/Mountaineer Workshop Manual
Page 1 of 5 SECTION 307-01B: Automatic Transmission 5R55E 1999 Explorer/Mountaineer Workshop Manual REMOVAL Procedure revision date: 07/27/1998 Transmission Special Tool(s) Torque Converter Holding Tool
More information1998 Ford EXPEDITION. Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS. Transmission
1998 Ford EXPEDITION Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS SECTION 307-01C: Automatic Transmission 4R100 1998 Expedition/Navigator Workshop Manual REMOVAL Procedure revision
More informationSTEPS Install the (A) input shaft with long spliced end first. Install the (B) aligning pin.
1999 Ford Truck Econoline E450 Super Duty V10-6.8L VIN S Vehicle > Transmission and Drivetrain > Automatic Transmission/Transaxle > Service and Repair > Overhaul > 4R100 > Assembly STEPS 51-94 51. Install
More informationPage 1 of 10 SECTION 307-01: Automatic Transaxle/Transmission 2005 Focus Workshop Manual ASSEMBLY Procedure revision date: 04/04/2008 Transaxle Printable View (2476 KB) Special Tool(s) Alignment Tool,
More informationPage 1 of 6 Section 07-01A: Transaxle, Automatic CD4E 1996 Probe Workshop Manual REMOVAL Procedure revision date: 06/14/2000 Transaxle Item Part Number Description 1 10655 Battery 2 10732 Battery Tray
More informationDescription. Cooling. Mechatronik module. Automatic Transmission (07.01) Transmission (07.00) transmission fault-finding.
Automatic Transaxle (07.01) Description The ZF 6HP26 automatic gearbox has the following features: Six forward speeds and One reverse A torque converter with an integral converter lock-up clutch Electronic
More informationPage 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description
More informationTransmission. All vehicles
INSTALLATION: TRANSMISSION (A... INSTALLATION: TRANSMISSION (AUTOMATIC TRANSAXLE/TRANSMISSION) 307 01 Automatic Transaxle/Transmission 2006 Mustang INSTALLATION Procedure revision date: 07/11/2008 All
More information1999 E-Series Workshop Manual
http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998
More informationDESCRIPTION AND OPERATION > TRANSAXLE DESCRIPTION
Page 1 of 10 2006 Mercury Montego 3.0L Eng Premier Service Manual: AUTOMATIC TRANSMISSION - CVT Print Date: DESCRIPTION AND OPERATION > TRANSAXLE DESCRIPTION This transaxle represents the start of a new
More informationPage 1 of 22 SECTION 307-01: Automatic Transaxle/Transmission 4R70E/4R75E ASSEMBLY Procedure revision date: 05/29/2009 Transmission Printable View (1554 KB) Special Tool(s) Air Test Plate, Transmission
More informationOil pan, oil strainer and valve body, removing and installing
Page 1 of 44 38-1 Oil pan, oil strainer and valve body, removing and installing WARNING! Do not run engine with the oil pan removed or without ATF filling and do not tow vehicle. Notes: Always replace
More informationOil Pan Replacement Buick Regal
2000 Buick Regal Oil Pan Replacement Removal Procedure Tools Required J 28467-90A Engine Support Adapters J 28467-B Universal Engine Support Fixture J 36462-A Engine Support Adapter Leg Set 1. Disconnect
More information2001 Lincoln LS Workshop Manual
Page 1 of 10 SECTION 303-01B: Engine 3.9L 2001 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/16/2000 Intake Manifold Removal 1. Disconnect the battery ground cable. For additional
More information1994 Bronco/Econoline/F-Series
Page 1 of 8 Section 10-01A: Fuel Tank, Filters, Lines and Electric Fuel Pump, Gasoline Engines REMOVAL AND INSTALLATION 1994 Bronco/Econoline/F-Series Workshop Manual Fuel Tank Steel Midship Fuel Tank,
More informationReturn to Instruction Sheet index TCI Installation Instructions for Turbo Hydramatic 350C & 250C
Page 1 of 6 Return to Instruction Sheet index TCI 326300 Installation Instructions for Turbo Hydramatic 350C & 250C NOTE: This kit was not intended for installation in transmissions that are in poor general
More information10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L
2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN
More informationASSEMBLY. Transmission Automatic Transmission 5R44E and 5R55E. Special Tool(s)
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 ASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Installer, Transmission Extension Housing
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
More informationTiming Belt: Service and Repair Installation
1998 Mercury Mystique L4-122 2.0L DOHC VIN 3 SFI Copyright 2008, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Installation NOTE:Ford does not provide camshaft gear timing marks, or information to
More information1997 Explorer/Mountaineer
Page 1 of 9 Section 308-07C: Transfer Case All-Wheel Drive DISASSEMBLY AND ASSEMBLY 1997 Explorer/Mountaineer Workshop Manual Transfer Case Special Service Tool(s) Bearing Cone Replacer T88T-7025-B Bearing
More informationCrankshaft Rear Seal with Retainer Plate
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Crankshaft Rear Seal with Retainer Plate Special Tool(s) Installer, Crankshaft Rear
More informationThe steering column is of a modular construction and features easy to service electrical switches.
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a01.htm~gen~ref.htm Page 1 of 3 Section 11-04A: Steering Column, Ranger DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Steering Column NOTE:
More informationSECTION B Manual Transaxle/Transmission TR6060
308-03B-i Manual Transaxle/Transmission TR6060 308-03B-i SECTION 308-03B Manual Transaxle/Transmission TR6060 CONTENTS PAGE Transmission... 308-03B-2 308-03B-2 Manual Transaxle/Transmission TR6060 308-03B-2
More information9/20/2017 Automatic Transaxle/Transmission External Controls - Selector Lever Cable - Removal and Installation 2008 Ford Edge MotoLogic
2008 Edge SECTION 307-05: Automatic Transaxle/Transmission External Controls REMOVAL AND INSTALLATION 2008 Edge/MKX Workshop Manual Procedure revision date: 06/17/2009 Report a problem with this article
More informationASSEMBLY. Transmission Automatic Transaxle/Transmission. Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P X) Special Tool(s)
307-01-1 Automatic Transaxle/Transmission 307-01-1 ASSEMBLY Transmission Special Tool(s) Adjustment Set, Transmission Band 307-S022 (T71P-77370-A) Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P-77103-X)
More informationTCI Trans-Scat
Page 1 of 5 Return to Instruction Sheet index TCI 350000 Trans-Scat Installation Instructions For TURBO HYDRAMATIC 350 This kit will allow you to reprogram your transmission to meet your driving needs
More informationEngine Front Cover. Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1) or equivalent. Support Bar, Engine 303-F070
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Engine Front Cover Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1)
More information2001 Ford FOCUS. Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS. Timing Belt
2001 Ford FOCUS Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS SECTION 303-01A: Engine??? 2.0L Zetec-E (Zetec) 2001 Focus Workshop Manual IN-VEHICLE REPAIR Procedure revision date:
More informationDIAGNOSIS AND TESTING
307-01B-1 DIAGNOSIS AND TESTING Special Testing Procedures The special tests are designed to aid the technician in diagnosing the hydraulic and mechanical portion of the transmission. Engine Idle speed
More information3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter
1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower
More informationDISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission.
308-03A-1 DISASSEMBLY Transmission 308-03A-1 Special Tool(s) Puller, Bearing 205-D064 (D84L-1123-A) or equivalent Remover/Installer, Front Wheel Hub 204-069 (T81P-1104-C) 2. Remove the 4 clutch housing
More information2004 DRIVELINE/AXLE. Rear Drive Axle - Corvette. Fastener Tightening Specifications Specification Application
2004 DRIVELINE/AXLE Rear Drive Axle - Corvette SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Differential Case Bolts 55 N.m
More information1 Green Pressure Regulator Spring Automatic transmissions operate at temperatures between 150ºF and
Installation Instructions for 603107 Valve Body Kit C-4 1970 & Later Tools Required Speed Handle or Ratchet 3/8 Drive 1/2 Socket 3/8 Drive 7/16 Socket 3/8 Drive 5/16 Socket 3/8 Drive Small Screwdriver
More informationPage 1 of 5 Section 03-01C: Engine, 4.0L V-6 IN-VEHICLE SERVICE Workshop Manual Camshaft SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Sensor Adjusting Wrench T94T-12270-A Removal NOTE: It is
More informationTransmission. Special Tool(s) Installation. All vehicles
Transmission Special Tool(s) Installation All vehicles 1. CAUTION: Prior to the installation of the transmission, the fluid, cooler lines and the cooler bypass valve must be cleaned. Transmission failure
More informationALLDATA Online Ford Focus L4-2.0L DOHC VIN 5 - Service and Repair. Service and Repair
Page 1 of 22 Service and Repair NOTE: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Belt Special
More informationDisconnect negative battery cable and remove coolant bottle cap.
1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use
More informationALLDATA Online - 1997 Ford Truck F 150 2WD Pickup V8-5.4L SOHC VIN L - Servi... Page 1 of 22 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference
More informationFord 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.
1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T
More informationEngine Front Cover. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Installer, Front Cover Oil Seal (T88T-6701-A)
SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/23/2008 Engine Front Cover Special Tool(s) 3-Jaw Puller 303-D121 or equivalent Installer, Front
More information2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.
2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position
More informationDISASSEMBLY Procedure revision date: 11/22/2001
Page 1 of 31 Evan Groenke From: Daniel Lelovic [dlelovic@rogers.com] Sent: May 8, 2005 12:06 PM To: 'Evan Groenke' Subject: 2.5 L Engine Disassembly SECTION 303-01B: Engine 2.5L 2000 Contour/Mystique Workshop
More informationDISASSEMBLY AND ASSEMBLY
307-01-1 Automatic Transaxle/Transmission 307-01-1 DISASSEMBLY AND ASSEMBLY Transaxle Special Tool(s) Dial Indicator Gauge With Holding Fixture 100-002 (TOOL-4201-C) Special Tool(s) Test Plate Screw Set,
More informationSECTION Automatic Transaxle/Transmission 6R80
307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE GENERAL PROCEDURES Transmission Fluid Drain and Refill... 307-01-2 Drain... 307-01-2
More informationIN-VEHICLE REPAIR Procedure revision date: 12/15/ Position the vehicle on a hoist. For additional information, refer to Section
2002 F-150 Applies to: 4R100 Report a problem with this article SECTION 307-01A: Automatic Transmission 4R100 2002 F-150 Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 12/15/2003 Main Control
More informationOil Pan July DDC-SVC-MAN-0081 DD Platform Installation of the Oil Pan Added graphics, additional torque specs.
7 17-13 1 7 17-13 SUBJECT DATE Oil Pan July 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081 DD Platform Installation of the Oil Pan Added
More informationTroubleshooting The Transmission Hydraulic System
416B, 426B, 428B, 436B, & 438B BACKHOE LOADERS TRANSMISSION Testing And Adjusting Troubleshooting The Transmission Hydraulic System Make reference to the following warning and pressure tap locations for
More informationIN-VEHICLE REPAIR. Engine Front Cover
303-01B-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01B-1 Special Tool(s) Motorcraft SAE 5W-20 WSS-M2C930-A Premium Synthetic Blend 3-Jaw Puller Motor Oil 303-D121 XO-5W20-QSP
More informationTCI TRANS-SCAT
Page 1 of 9 Return to Instruction Sheet index TCI 360000 TRANS-SCAT Installation Instructions for FORD C-6 Transmissions TCI s TRANS-SCAT kit will allow you to calibrate the performance of your transmission.
More informationIN-VEHICLE REPAIR. Upper Intake Manifold
303-01-1 Engine 3.9L and 4.2L 303-01-1 IN-VEHICLE REPAIR Upper Intake Manifold Special Tool(s) Remover, Spark Plug Wire 303-106 (T74P-6666-A) Material Item Silicone Brake Caliper Grease and Dielectric
More informationCERTAIN MODEL YEAR FUSION AND ESCAPE VEHICLES EQUIPPED WITH A 6F35 TRANSMISSION SHIFTER CABLE BUSHING REPLACEMENT
PAGE 1 OF 9 CERTAIN 2013-2016 MODEL YEAR FUSION AND 2013-2014 ESCAPE VEHICLES EQUIPPED WITH A 6F35 TRANSMISSION SHIFTER CABLE BUSHING REPLACEMENT OVERVIEW In some of the affected vehicles, the bushing
More information2003 Volkswagen Passat GL
2001-03 AUTOMATIC TRANSMISSIONS Removal & Installation - 01V APPLICATION TRANSAXLE APPLICATION Application Transaxle Model Passat 1.8L (FWD) 01V 2.8L (FWD & 4WD) 01V 4.0L (AWD) 2002-03 01V REMOVAL & INSTALLATION
More informationDISASSEMBLY TRANSAXLE DISASSEMBLY AND ASSEMBLY. Part 1 Of 3
2004 Mitsubishi Truck Endeavor V6-3.8L SOHC Vehicle > Transmission and Drivetrain > Automatic Transmission/Transaxle > Service and Repair > Overhaul > F4A5A > Disassembly and Assembly DISASSEMBLY TRANSAXLE
More informationPage 6 of 6 OUTLAW DIESEL EGR COOLER DELETE KIT W/INTAKE ELBOW L FORD POWERSTROKE
What s in the box 1 Exhaust Block-Off Plate 1 Exhaust Gasket 2 Coolant Line Plugs 1 Brass Barbed Hose Connector 1 Stand-off Spacer 4 M10-1.25 x 40 Hex Head Bolts (Exhaust Manifold) 2 M10-1.25 x 20 Hex
More information2003 F-Super Duty /Excursion Workshop Manual
Page 1 of 16 SECTION 303-01C: Engine 7.3L Diesel DISASSEMBLY Procedure revision date: 05/21/2002 Engine Printable View (1761 KB) Special Tool(s) Cylinder Head Lifting Tool (D94T-6000-B) 303-D098 Damper
More informationAUTO TRANS OVERHAUL - V.A.G. 01V Article Text 1998 Volkswagen Passat This file passed thru Volkswagen Technical Site -
AUTO TRANS OVERHAUL - V.A.G. 01V Article Text 1998 Volkswagen Passat This file passed thru Volkswagen Technical Site - http://volkswagen.msk.ru ARTICLE BEGINNING 1997-98 AUTOMATIC TRANSMISSIONS Volkswagen/Audi
More informationTRANSMISSION SERVICING - A/T Article Text 1998 Volkswagen Passat This file passed thru Volkswagen Technical Site -
TRANSMISSION SERVICING - A/T Article Text 1998 Volkswagen Passat This file passed thru Volkswagen Technical Site - http://volkswagen.msk.ru ARTICLE BEGINNING 1997-98 TRANSMISSION SERVICING Automatic Transmission
More informationSECTION C Engine 5.4L (3V)
303-01C-i Engine 5.4L (3V) 303-01C-i SECTION 303-01C Engine 5.4L (3V) CONTENTS PAGE IN-VEHICLE REPAIR Engine Front Cover... 303-01C-2 303-01C-2 Engine 5.4L (3V) 303-01C-2 IN-VEHICLE REPAIR Engine Front
More informationThis information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.
Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers
More information1991 TRANSMISSION SERVICING Automatic Transmission. Mitsubishi: Eclipse, Galant, Mirage, Montero, Pickup, Precis, 3000GT
Article Text ARTICLE BEGINNING 1991 TRANSMISSION SERVICING Automatic Transmission Mitsubishi: Eclipse, Galant, Mirage, Montero, Pickup, Precis, 3000GT IDENTIFICATION MITSUBISHI AUTOMATIC TRANSMISSION APPLICATIONS
More information2000 F-Super Duty /Excursion/F-53 Motorhome Chassis Workshop Manual
Page 1 of 9 SECTION 307-01: Automatic Transaxle/Transmission 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 12/15/2003 Main Control
More information26 November 2009 Valve Body # / BD VALVE BODY. For Dodge 5.9L 12V Cummins Trucks
26 November 2009 Valve Body #1030410 / 1030415 1 BD VALVE BODY For 1991-1995 Dodge 5.9L 12V Cummins Trucks - - I n s t a l l a t i o n I n s t r u c t i o n s - - 1030410 1991-1993 Dodge (4 Spd) 618 1030415
More informationTransaxle. 1. Mount the transaxle to Bench Mounted Holding Fixture T57L-500-B.
«1997 Aspire Table of Contents» «Group 07: TRANSAXLE» «Section 07-01: Transaxle, Automatic» «DISASSEMBLY» Transaxle CAUTION: To prevent dirt from entering the transaxle, it should be disassembled and kept
More information2002 Taurus/Sable Workshop Manual
SECTION 211-02: Power Steering REMOVAL AND INSTALLATION 2002 Taurus/Sable Workshop Manual Power Steering Pump Pulley CII Pump Special Tool(s) Installer, Power Steering Pump Pulley 211-009 (T65P-3A733-C)
More information6.4L EGR Delete With Intake Elbow
6.4L EGR Delete With Intake Elbow J I E C B F D G H A Part# A B C D E F G H I J PACKING LIST: QTY. 2 4 2 4 2 Description Exhaust Block-Off Plate Exhaust Gasket Coolant Line Plugs Brass Barbed Hose Connector
More informationMANUAL TRANSMISSIONS. Servicing - Corvette. Transmission Model (RPO Code) Borg-Warner T56 6-Speed (M12)
2003-04 MANUAL TRANSMISSIONS Servicing - Corvette APPLICATION TRANSMISSION APPLICATION Application Corvette Convertible & Coupe Z06 Transmission Model (RPO Code) Borg-Warner T56 6-Speed (MM6) Borg-Warner
More information1. Remove the battery tray. For additional information, refer to Battery Tray ( )
Page 1 of 11 Removal 1. Remove the battery tray. For additional information, refer to Battery Tray (86.15.11) 2. Remove the air cleaner. For additional information, refer to Air Cleaner (19.10.05) 3. NOTE
More informationPowerglide Automatic Floor Mount Shifter Installation Instructions
Powerglide Automatic Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 (865) 966-2269 FAX (865) 671-1999 tech@lokar.com www.lokar.com Powerglide
More informationBD PERFORMANCE TRANSMISSION
1 BD PERFORMANCE TRANSMISSION 2008-10 F o r d 6. 4 L ( 5 R 1 1 0 ) I n s t a l l a t i o n I n s t r u c t i o n s 4WD Part # 1064494 2WD Part # 1064492 Please read the instructions and warranty disclaimer
More informationValve Body: Service and Repair
2007 Chevy Truck TrailBlazer 2WD L6-4.2L Copyright 2013, ALLDATA 10.52SS Page 1 Valve Body: Service and Repair Valve Body and Pressure Switch Replacement Removal Procedure 1. Ensure that removal of the
More informationWSS-M2C931- B. 1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Oil Filter Adapter Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1)
More informationIN-VEHICLE SERVICING > VALVE COVER - RH
Page 1 of 20 Service Manual: ENGINE - 5.4L (3V)- F-150 & MARK LT IN-VEHICLE SERVICING > VALVE COVER - RH 2008 Ford Pickup 5.4L Eng F150 Material Item Specification Motorcraft Metal Surface Prep ZC-31 PAG
More informationSECTION Automatic Transaxle/Transmission 4R70E/4R75E
307-01-i Automatic Transaxle/Transmission 4R70E/4R75E 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 4R70E/4R75E CONTENTS PAGE Transmission Four Wheel Drive (4WD)... 307-01-2 307-01-2 Automatic
More informationINTAKE MANIFOLD INSPECTION/REPLACEMENT
ATTACHMENT III Owner Notification Program 99M01 INTAKE MANIFOLD INSPECTION/REPLACEMENT AFFECTED VEHICLES: 1997 AND 1998 CROWN VICTORIA POLICE INTERCEPTOR VEHICLES WITH 4.6L SOHC ENGINES BUILT AT THE ST.
More information2011 Mercury Grand Marquis LS
Fig. 6: Locating Intake Manifold Crash Bracket With Tie Strap 24. Remove the intake manifold crash bracket bolt. 25. Disconnect the fuel rail pressure and temperature sensor vacuum and electrical connectors.
More informationReturn to Instruction Sheet index. Installation Instructions For C-4 70 and Later, Except 70 Falcon
Page 1 of 8 Return to Instruction Sheet index TCI 260100 Trans-Scat Automatic Transmission Installation Instructions For C-4 70 and Later, Except 70 Falcon TCI 260100 Kit Contains: Qty. Description One
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009
NUMBER: 8 5 09 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009 SUBJECT: CYLINDERHEADCOOLANTVENTLINE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change
More informationBR 43. BRAKE HYDRAULIC BRAKE BOOSTER (w/ VSC) REMOVAL
AKE HYDRAULIC AKE BOOSTER (w/ VSC) 43 REMOVAL Before starting the work, make sure that the ignition switch is OFF and depress the brake pedal more than 20 times. As high pressure is applied to the brake
More informationInstallation Instructions
2011-2013 LML DURAMAX COMPOUND-ADD 2011-2015 LML A Duramax TURBO KIT Add INSTALL A Turbo INSTRUCTIONS Compound Kit Installation Instructions 1-800-955-0476 - www.industrialinjection.com - info@industrialinjection.com
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Valve Cover» Service and Repair» Procedures» LH Valve Cover LH Removal 1. Disconnect the battery ground cable. 2. Remove the air cleaner
More informationPart No amatic 350
Watch our installation video on YouTube Installation Instructions Shift Improver Kit Part No. 30262 1968-1981 TurboHy urbohydr drama amatic 350 B&M Racing and Performance Products 2002 Congratulations!
More information303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine
2010 MKZ Report a problem with this article 303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid REMOVAL Procedure revision date: 10/19/2012 Engine Special Tool(s) 2,200# Floor Crane,
More information