Series P Series P. Penguin Vertical Pump

Transcription

1 Features: Choice of CPVC, PVDF, or Polypropylene Sealless Runs Dry Without Damage Self-Priming When Immersed No Metal Contact Chemical Resistant Extended Pump Lengths Available (See Bulletin 1) Recommended Applications: Sump Pumping / Draining Transfer Pumping Recirculation Pumping Plating Wet Fume Scrubbing Waste Treatment Wet Processing Etching Filtering Flows from 9 to 17 GPM Pressure to 1 Ft. Model P-7 1/AK vertical immersible pumps are compact, portable, and self-priming when immersed. Simple in design and effi cient in performance, this pump has only one moving part. Constructed completely of CPVC, polypropylene, or PVDF where in contact with the solution, this pump is suitable for pumping, agitating, fi ltering, or circulating acid and alkaline solutions (ph 0-14), abrasive fl uids, and other corrosive solutions. Maximum temperature ratings are as follows: CPVC-180ºF, polypropylene-ºf, and PVDF-0ºF. Because PVDF is ultra pure, it is recommended for use in high purity deionized water, HF, and liquids that must remain contamination free. The vertical pump has a rigid, solid stainless steel, one-piece rotor drive shaft covered with a two-piece sleeve and impeller. Titanium shafts are available as an option. Because of the unique double impeller design, this pump has no seals, no pump bearings, no bushings, no wearing parts, and thus requires little maintenance. As a standard feature on our P-1/4 model and up, the vertical pump comes equipped with a plugged air purge in the bottom (shaft end) endbell of the motor. If utilized, this air purge requires a minimum of psi to create a positive displacement, extending the life of the lower motor bearing. The vertical pump is equipped with a totally enclosed fan cooled (TEFC) motor. Most motor housings come standard with epoxy coating for additional corrosion resistance and oversized shaft end bearings for longer life and easy replacement. Single phase motors are wired 11V and equipped with a foot cord and grounded plug unless otherwise specifi ed. All three phase motors are shipped unwired. vertical pumps are versatile, easy to install, and require a minimal amount of tank space, thus saving valuable fl oor space. Most can be easily moved from tank to tank, with mounting either internally or externally on the tank fl ange. Bulletin 01M /07

2 Design Features On Most Models Performance Charts P-1/ GPM LPM P-1/ GPM LPM P-1/4 1. Motor fan cover with drip shield.. Standard TEFC Epoxy coated motor.. Air purge plug. 4. One-piece stainless steel rotor shaft assembly. Optional 1 SS or Titanimm shaft available on most models.. Viton vapor seal/fume barrier assembly.. Sleeved O-ring sealed compound impeller for non metallic solution contact. 7. Overfl ow GPM LPM.4.

3 Performance Charts P-1/ P-/ GPM LPM GPM LPM P-/4 P GPM LPM P-1/ GPM LPM P-1 1/ 9 0 0HZ HZ HZ HZ 0HZ GPM LPM HZ 0HZ 0HZ GPM LPM 1..

4 Performance Charts P- P GPM LPM GPM LPM P- P-7 1/ M FT. M FT " " GPM LPM " " " 7" GPM LPM Mounting Diagram P1/ - P Mounting Diagram P - P7 1/ /8 ø 4. 4 SLOTS.4 WIDE 7- /8 (ref) / - 1 / 1 / / 4

5 Top View SEE NOTES P-1/1 P-1/ P-1/4 P-1/-P- P- & P-7 1/ Dimensions Model A B C D E F G H Suction Discharge P-1/1 1/ 1/ /4 9 /8 /8 14 /8 /4 /8 /4 MPT 1/ FPT P-1/ 1/4 1/4 1/ 8 7/8 1 1/ 4 1 P-1/4 1/ 8 9 /8 19 /8 1 1/8 1 FPT /4 FPT P-1/ /4 /4 /4 1 /4 1/4 1/ 1 1/4 P-1/ 4 1/ 1/ /8 /8 1 /8 1 1/ FPT P-/4 /4 /4 /4 1 /4 1/4 1/ 1 1/4 1 1/4 FPT P-/4 9 1/4 1 MPT P-1 4 1/ 1/ /8 /8 1 /8 1 1/ FPT P-1 1/ P- /4 P-* / 8 1/4 1 1/8 1 1/MPT P-* FPT P-7 1/ 1/ 1 / 1 /8 8 /4 1/8

6 Specifications Max Max Max Max Model Flow Head Flow Head Motor Dimensions (gpm) (ft) 0HZ (LPM) 0HZ (M) RPM Volts Hertz Phase Amps Ht Wth Lth Wt P-1/ /1 000/ / 00/ P-1/ / / P-1/ / 40 1/0.4/ /40 1./0. 11/ /.9 4 P-1/ /. 47 1/ 08-0/40 0/ / / /.9 4 P-1/ 4 0/0.4/ / /9 4 11/ / P-/ /4 0/0 / /40.7-./ / / P-/ /4 40 0/0 / /40.7-./ / /. 0 P /0 1.8/ /40.4-./1. 47 P- 1 1/ / 11/ / / /. 48 P /.7 0 P / /40 P / P-7 1/ / /9. Nomenclature P XX X - XX - XX - XX - XX Vertical Pump Horsepower Construction Material/O-Ring Elastomer Material Impeller/Housing Configuration Shaft Configuration Shaft Material 1 Pump Bracket Config. 1/1=1/1 1/=1/ 1/4=1/ 1/=1/ /4=/4 1=1 1 1/=1 1/ = = = 7 1/=7 1/ A = CPVC/EPR B = Polypropylene/EPR C = PVDF/Viton None = Standard = High Pressure 1 None = Threaded K = Keyway/Thrd Screw&Nut None = 1SS T = Titanium None=Bracket RB = Round Flange DP = Bracket Rigid Plumbed RB round flange applies to models P, P & 7 1/ only. B polypro and C PVDF models are only available with RB round flange configuration. A CPVC models are available with standard bracket. Optional RB includes round flange Optional DP includes bracket and rigid plumbed configurations. K Keyway impeller-p, P & P7-1/ K Threaded screw/w nut impeller-1/, /4, 1, 1-1/, Bulletin 01M /07