Hydraulic Hose. Hardy Spicer, Discovery Road, Dandenong South, Victoria, 3175 Toll free Ph:

Transcription

1 , 1-31 Discovery Road, Dandenong South, Victoria, 315 Toll free Ph:

2 DISCLAIMER Disclaimer The information and dimensions listed in these catalogues is correct to the best of our knowledge and belief, having been compiled from reliable and official sources of information. However (HS Company Pty Ltd) accepts no responsibility for possible errors, omissions or unsuitable parts being listed or fitted to any vehicle. Dimensions listed are nominal throughout. Due to our continuous product and range development we reserve the right to alter the specification without prior notice. We welcome any feedback re suspected errors or omissions to the information enclosed. We can be contacted via Or via Ph or Fax Alternatively via mail at PO Box 4262, Dandenong South, Vic D:1-II of Catalogue

3 HOSE CONTENTS Part No. Description / Standard Page No. Low / Suction / Push lock GMV Suction / Return Hose (Global MegaVac) D:1-16 R4 Suction / Return Hose D:1-16 RLA 1-Fiber Braid Return Line & Low D:1-1 RLC 3-Fiber Braid Return Line & Low D:1-1 LOC 1-Fiber Braid Lock-On Hose Cotton Cover D:1-18 LOL Lock-On Hose D:1-19 Medium / High (Braided) G1 SAE 100 R1AT D:1-13 G2 SAE 100 R2AT D:1- M2T SAE 100 R16 (MegaFlex) D:1-8 CM2T SAE 100 R16 (Twin Line MegaFlex) D:1-9 M3K SAE 100 R1 D:1-11 M6K / M5K / M4K MegaSys Hose D:1-9 Very High (Spiral) EFG3K SAE 100 R12 D:1-6 EFG4K SAE 100 R12 D:1-5 EFG5K SAE 100 R13 D:1-4 EFG6K SAE 100 R15 D:1-3 High Temperature G1H SAE 100 R1AT D:1-14 G2H SAE 100 R2AT D:1-12 G2XH SAE 100 R2AT D:1-12 G3H SAE 100 R3 D:1-15 GTH SAE 100 R6 D:1-15 ACP High-Temp Oil / Air Return & Air Brake Hose D:1- Special Product Hoses TR500 Air Brake / Engine Hose D:1-21 MegaTech250 High-Temp Transmission Oil Cooler Hose D:1-22 MegaTech500 High-Temp Oil / Air Return & Air Brake Hose D:1-22 MegaTech1000 High-Temp Oil / Air Return & Air Brake Hose D:1-21 C5CXH High-Temp Extreme Heat Hose D:1-23 PS188 Power Steering Hose D:1-30 PC / PW Power Clean / Wash Hose D:1-20 AC134 Polar Seal Refrigerant Hose D:1-30 C5C SAE 100 R5 D:1-24 C5D Multi Fluid High Temp Hose D:1-24 C5M Marine Fuel Line Hose D:1-25 C5E High Temp Hose D:1-25 TF/1 Teflon Hose D:1-26 TH / TH8 Thermoplastic Hose D:1-2 of Catalogue D:1-1

4 CONTENTS Cont. Part No. Description / Standard Page No. RFS Red Fire Suppressant Hose D:1-14 J2AT Jack Hose IJ 100 D:1-13 G2L Polar Flex Hose D:1-8 WBA Waterblast Hose Assembly D:1-32 Multi Purpose Hoses PREMO PremoFlex Hose D:1-31 TERMINATOR Terminator Hose D:1-31 D:1-2 of Catalogue

5 Extremely High For Biodegradable Hydraulic Fluids Recommended For: Extremely high pressure, high impulse applications such as hydrostatic transmissions. EFG6K is designed to meet all requirements of SAE 100R15 specifications and performance requirements of EN 856 4SP (-6, -8, -10, and -12) and EN 856 4SH (-12, -16, and -20). Compatible with biodegradable hydraulic fluids like polyolester, polyglycol and vegetable oil as well as standard petroleum based fluids. Available in 36M and 60M coils. Tube: Black, oil-resistant synthetic rubber (Nitrile-Type C) Reinforcement: Four (six for -20,-24 & -32) alternating layers of spiraled, high tensile steel. Cover: Black, oil resistant, synthetic rubber (Neoprene Type A). Colour coded layline. Available with unique abrasion-resistant MegaTuff cover. EFG6K Spiral Wire Hose - SAE 100R15 (Meets Flame Resistance Acceptance Designation US. MSHA2G ) Temperature Range: -40 C to +121 C GS Fittings up to -20 GSM Fittings for -24 & -32 EFG6K / / / / / 30 EFG6K / / / / / 30 EFG6K / / / / / 30 EFG6K / / / / / 30 EFG6K / / / / 30 EFG6K / / / / / 15 EFG6K / / / / / 15 EFG6K / / / / 15 MEGATUFF COVER Megatuff hose lasts up to 300 times longer than standard hose during hose-to-hose amd hose-to-metal abrasion tests per ISO 6945 EFG6K-08-MTF / / / / / 30 EFG6K-10-MTF / / / / / 30 EFG6K-12-MTF / / / / / 30 EFG6K-16-MTF / / / / 30 EFG6K-20-MTF / / / / / 15 EFG6K-24-MTF / / / / / 15 EFG6K-32-MTF / / / / 15 of Catalogue D:1-3

6 Extremely High For Biodegradable Hydraulic Fluids Recommended For: Extremely high pressure, hydraulic applications. EFG5K is designed to meet all requirements of SAE 100R13 specifications and performance requirements of EN 856 4SH (-16 and -20) and EN 856 4SP (-8, -10, and -12) and EN 856 R13. Compatible with biodegradable hydraulic fluids like polyolester, polyglycol and vegetable oil as well as standard petroleum based fluids. Available in 36M and 60M coils. Tube: Black, oil-resistant synthetic rubber (Nitrile-Type C) Reinforcement: Four layers of alternated spiraled, high tensile steel wire on -12 and -16 sizes - six layers of alternated spiraled, high tensile steel wire on -20, -24 & -32 size. Cover: Black, oil resistant, synthetic rubber (Neoprene). Colour coded layline. Available with unique abrasion-resistant MegaTuff cover. EFG5K Spiral Wire Hose - SAE 100R13 (Meets Flame Resistance Acceptance Designation US. MSHA2G ) Temperature Range: -40 C to +121 C GS Fittings up to -20 GSM Fittings for -24 & -32 EFG5K / / / / / 30 EFG5K / / / / / 30 EFG5K / / / / / 30 EFG5K / / / / / 30 EFG5K / / / / 30 EFG5K / / / / / 15 EFG5K / / / / / 15 EFG5K / / / / 15 MEGATUFF COVER Megatuff hose lasts up to 300 times longer than standard hose during hose-to-hose amd hose-to-metal abrasion tests per ISO 6945 EFG5K-06-MTF / / / / / 30 EFG5K-08-MTF / / / / / 30 EFG5K-10-MTF / / / / / 30 EFG5K-12-MTF / / / / / 30 EFG5K-16-MTF / / / / 30 EFG5K-20-MTF / / / / / 15 EFG5K-24-MTF / / / / / 15 EFG5K-32-MTF / / / / 15 D:1-4 of Catalogue

7 Extremely High For Biodegradable Hydraulic Fluids Recommended For: Extremely high pressure, high impulse applications. Exceeds all performance requirements for SAE 100R12, EN 856 R12 and EN 856 4SP (-16) Compatible with biodegradable hydraulic fluids like polyolester, polyglycol and vegetable oil as well as standard petroleum based fluids. Available in 36M and 60M coils. Tube: Black, oil-resistant synthetic rubber (Nitrile-Type C) Reinforcement: Four alternating layers of spiraled, high tensile steel wire. Cover: Black, oil resistant, synthetic rubber (Neoprene Type A). Colour coded layline. Available with unique abrasion-resistant MegaTuff cover. EFG4K Spiral Wire Hose - SAE 100R12 (Meets Flame Resistance Acceptance Designation US. MSHA2G ) Temperature Range: -40 C to +121 C GS Fittings EFG4K / / / / / 30 EFG4K / / / / / 30 EFG4K / / / / / 30 EFG4K / / / / / 30 EFG4K / / / / 30 EFG4K / / / / / 15 MEGATUFF COVER Megatuff hose lasts up to 300 times longer than standard hose during hose-to-hose amd hose-to-metal abrasion tests per ISO 6945 EFG4K-06-MTF / / / / / 30 EFG4K-08-MTF / / / / / 30 EFG4K-10-MTF / / / / / 30 EFG4K-12-MTF / / / / / 30 EFG4K-16-MTF / / / / 30 EFG4K-20-MTF / / / / / 15 of Catalogue D:1-5

8 Extremely High Recommended For: Extremely high pressure, high impulse applications. Exceeds all requirements of SAE 100R12 and EN 856 R12 and performance requirements of EN 856 4SP. Compatible with biodegradable hydraulic fluids like polyolester, polyglycol and vegetable oil as well as standard petroleum based fluids. Available in 36M and 60M coils. Tube: Black, oil-resistant synthetic rubber (Nitrile-Type C) Reinforcement: Four alternating layers of spiraled, high tensile steel wire. Cover: Black, oil resistant, synthetic rubber (Neoprene). Colour coded layline. Available with unique abrasion-resistent MegaTuff cover. Temperature Range: -40 C to +121 C Global EFG3K Spiral Wire Hose - SAE 100R12 GS Fittings for -20 GSP Fittings for -24 & -32 EFG3K / / / / / 30 EFG3K / / / / / 15 EFG3K / / / / 15 MEGATUFF COVER Megatuff hose lasts up to 300 times longer than standard hose during hose-to-hose amd hose-to-metal abrasion tests per ISO 6945 EFG3K-20-MTF / / / / / 15 EFG3K-24-MTF / / / / / 15 EFG3K-32-MTF / / / / 15 D:1-6 Catalogue of

9 High Recommended For: High hydraulic oil lines. Meets or exceeds the requirements of SAE 100R2AT and SAE 100R2 types and performance requirements of EN 853 2SN. Tube: Black, oil-resistant synthetic rubber (Nitrile-Type C) Reinforcement: Two braids of high-tensile steel wire. Cover: Black, oil and abrasion resistant thin synthetic rubber (Modified Nitrile) Temperature Range: -40 C to +100 C Global G2 2-Wire Braid Hose - SAE 100R2 Type AT PC Fittings for -03 (except -24 and -32). GSP Fittings for -24 and -32 Bulk Reel G / / / / / 134 G / / / / / 16 G / / / / / 121 G / / / / / 100 G / / / / / 6 G / / / / / 6 G / / / / 50 G / / / / / 36 G / / / / / 36 G / / / / 36 High MegaTech II ACP Hot Oil/Air Line - SAE 100R2 Type AT Recommended For: Multipurpose high pressure, high temperature, air compressor lines, petroleum-base or phosphate ester hydraulic fluid supplies. Meets or exceeds the requirements of SAE 100R2AT and SAE 100R2 Type S. Tube: Black, oil-resistant synthetic rubber (CPE-Type J). Reinforcement: Two braids of high-tensile steel wire. Cover: Blue, oil and abrasion resistant polyester braid. Temperature Range: -40 C to +149 C for -20 Permanent GSP Fittings for -24 and -32 ACP / / / / / 40 ACP / / / / / 40 ACP / / / / 40 of Catalogue D:1-

10 High Global G2L PolarFlex Hose - SAE 100R2 Type AT Recommended For: High pressure, hydraulic oil lines. Meets or exceeds the requirements of SAE 100R2AT and performance requirements of EN 853 2SN. Tube: Black, oil-resistant synthetic rubber (Nitrile-Type C). Reinforcement: Two braids of high-tensile steel wire. Cover: Black, oil and abrasion resistant thin synthetic rubber (Neoprene). Temperature Range: -5 C to +100 C Bulk Reel G2L / / / / / 134 G2L / / / / / 11 G2L / / / / / 101 G2L / / / / / 6 G2L / / / / / 6 G2L / / / / 50 G2L / / / / / 34 High Recommended For: High pressure, hydraulic oil lines. Exceeds SAE 100R16 requirements. M2T hose has smaller exterior dimensions and significantly tighter bend radius. Tube: Black, oil-resistant synthetic rubber (Nitrile-Type C) Reinforcement: Two braids of high-tensile steel wire. Cover: Black, oil, abrasion and weather resistant, synthetic rubber (Modified Nitrile - Type C2). Green stripe layline. Available with unique abrasion-resistent MegaTuff cover. Temperature Range: -40 C to +100 C M2T Plus Megaflex 2 Wire Braid Hose - SAE 100R16 Bulk Reel M2T / / / / / 168 M2T / / / / / 11 M2T / / / / / 101 M2T / / / / / 6 M2T / / / / / 6 M2T / / / / 50 MEGATUFF COVER Megatuff hose lasts up to 300 times longer than standard hose during hose-to-hose amd hose-to-metal abrasion tests per ISO 6945 M2T-04-MTF / / / / / 10 M2T-06-MTF / / / / / 101 M2T-08-MTF / / / / / 101 M2T-10-MTF / / / / / 6 M2T-12-MTF / / / / / 6 M2T-16-MTF / / / / 50 D:1-8 Catalogue of

11 High Recommended For: High hydraulic oil lines. Meets SAE 100R16 requirements. CM2T hose has smaller exterior dimensions and significantly tighter bend radius. Exceeds performance standards of EN 85 2SC and ISO/DIS Tube: Black, oil resistant synthetic rubber (Nitrile-Type C). Reinforcement: Two braids of high-tensile steel wire. Cover: Black, oil, abrasion and weather resistant synthetic rubber (Modified Nitrile - Type C). Temperature Range: -40 C to +100 C CM2T Megaflex Connected TwinLine 2 Wire Braid Hose SAE 100R16. Bulk Reel CM2T / / / / / 65 CM2T / / / / / 55 High Recommended For: High pressure hydraulic applications. Provides tighter than standard minimum bend radius and greater flexibility for easier plumbing. Tube: Black, oil-resistant synthetic rubber (Nitrile-Type C) Reinforcement: Two braids of high tensile steel wire. Cover: Black, oil, abrasion and weather resistant synthetic rubber (Modified Nitrile - Type C). Colour coded layline Temperature Range: -40 C to +100 C Global M6K Mega6000 Hose Bulk Reel M6K / / / / / 134 High Recommended For: High pressure hydraulic applications. Provides tighter than standard minimum bend radius and greater flexibility for easier plumbing. Tube: Black, oil-resistant synthetic rubber (Nitrile-Type C) Reinforcement: Two braids of high tensile steel wire. Cover: Black, oil, abrasion and weather resistant synthetic rubber (Modified Nitrile - Type C). Colour coded layline Temperature Range: -40 C to +100 C Global M5K Mega5000 Hose Bulk Reel M5K / / / / / 134 M5K / / / / / 10 M5K / / / / / 101 M5K / / / / / 6 of Catalogue D:1-9

12 High Recommended For: High pressure hydraulic applications. Provides tighter than standard minimum bend radius and greater flexibility for easier plumbing. The plus symbol indicates development testing at 150% of maximum working pressure up to 600,000 impulse cycles. Tube: Black, oil-resistant synthetic rubber (Nitrile-Type C) Reinforcement: Two braids of high tensile steel wire. Cover: Black, oil, abrasion and weather resistant synthetic rubber (Modified Nitrile - Type C). Colour coded layline. Available with unique abrasion-resistent MegaTuff or XtraTuff cover. Temperature Range: -40 C to +100 C Global M4K+ Mega4000 Hose up to -12 GS Fittings for -16 Bulk Reel M4K / / / / / 134 M4K / / / / / 101 M4K / / / / / 6 M4K / / / / / 6 M4K / / / / / 6 M4K / / / / 50 XTRATUFF COVER Xtratuff hose lasts up to 25 times longer than standard hose during hose-to-hose amd hose-to-metal abrasion tests per ISO 6945 M4K-04-XTF / / / / / 134 M4K-06-XTF / / / / / 101 M4K-08-XTF / / / / / 6 M4K-10-XTF / / / / / 6 M4K-12-XTF / / / / / 6 M4K-16-XTF / / / / 50 MEGATUFF COVER Megatuff hose lasts up to 300 times longer than standard hose during hose-to-hose amd hose-to-metal abrasion tests per ISO 6945 M4K-04-MTF / / / / / 10 M4K-06-MTF / / / / / 101 M4K-08-MTF / / / / / 6 M4K-10-MTF / / / / / 6 M4K-12-MTF / / / / / 58 M4K-16-MTF / / / / 50 D:1-10 Catalogue of

13 High Global M3K Mega3000 Hose - SAE 100R1 Recommended For: High hydraulic oil lines. Meets SAE 100R1 requirements and performance requirements of EN 85 1SC. M3K hose has smaller exterior dimensions and significantly tighter bend radius than other SAE 100R1 and 100R2 hose. Tube: Black, oil-resistant synthetic rubber (Nitrile-Type C). Reinforcement: Braided high-tensile steel wire. -4, -5, -6 and -8 sizes are one braid; -10, -12, and -16 sizes are two braid. Cover: Black, oil, abrasion and weather resistant synthetic rubber (Modified Nitrile). Colour coded layline. Available with unique abrasion-resistant Megatuff or XtraTuff cover. Temperature Range: -40 C to +100 C Bulk Reel M3K / / / / / 134 M3K / / / / / 11 M3K / / / / / 101 M3K / / / / / 6 M3K / / / / / 6 M3K / / / / / 6 M3K / / / / 50 XTRATUFF COVER Xtratuff hose lasts up to 25 times longer than standard hose during hose-to-hose amd hose-to-metal abrasion tests per ISO 6945 M3K-04-XTF / / / / / 134 M3K-05-XTF / / / / / 11 M3K-06-XTF / / / / / 101 M3K-08-XTF / / / / / 6 M3K-10-XTF / / / / / 6 M3K-12-XTF / / / / / 6 M3K-16-XTF / / / / 50 MEGATUFF COVER Megatuff hose lasts up to 300 times longer than standard hose during hose-to-hose amd hose-to-metal abrasion tests per ISO 6945 M3K-04-MTF / / / / / 134 M3K-06-MTF / / / / / 101 M3K-08-MTF / / / / / 6 M3K-10-MTF / / / / / 6 M3K-12-MTF / / / / / 6 M3K-16-MTF / / / / 50 of Catalogue D:1-11

14 High Global G2H High-Temp 2 Wire Braid Hose SAE 100R2 Type AT Recommended For: High hydraulic oil lines. Meets or exceeds the requirements of SAE 100R2AT and performance requirements of EN 853. Tube: Black, oil-resistant synthetic rubber (Nitrile-Type C) Reinforcement: Two braids of high-tensile steel wire. Cover: Black, oil-resistant synthetic rubber (Hypalon). Available with unique abrasion-resistent MegaTuff Temperature Range: -40 C to +135 C constant and +149 C intermittent (up to 10% of operating time) (-20). GSP Fittings for -24 and -32 G2H / / / / / 36 G2H / / / / / 36 G2H / / / / 36 MEGATUFF COVER Megatuff hose lasts up to 300 times longer than standard hose during hose-to-hose amd hose-to-metal abrasion tests per ISO 6945 G2H-20-MTF / / / / / 30 G2H-24-MTF / / / / / 30 G2H-32-MTF / / / / 30 High Recommended For: High hydraulic applications where pressure or temperature requirements exceed SAE 100R2AT Type S and EN 853 2SN or where resistance to either petroleum-base or phosphate ester fluids is required. Tube: Black, Specifically compounded for temperature and chemical resistance. (CPE - Type J) Reinforcement: Two braids of high tensile steel wire. Cover: Blue, oil and abrasion resistant thin synthetic rubber (CSM - Type M). Temperature Range: Petroleum based fluids -40 C to +149 C. Phosphate ester fluids as recommended by the fluid manufacturer, but within a range of -40 C to +100 C. For water emulsions: Max +10 C pressure lines, Max +82 C return lines. Global G2XH 2 Wire Braid Extreme Heat Hose SAE 100R2 Type AT Caution: Special O-Rings are required for phosphate ester fluid applications. Many male swivel fittings have internal O- Rings that are not recommended for phosphate ester fluids. Bulk Reel G2XH / / / / / 16 G2XH / / / / / 121 G2XH / / / / / 100 G2XH / / / / / 6 G2XH / / / / / 6 G2XH / / / / 50 G2XH / / / / / 36 G2XH / / / / / 40 G2XH / / / / 40 D:1-12 Catalogue of

15 High Recommended For: Hydraulic Jack applications. Meets material Handling Institute specification IJ 100 for hydraulic hose and assemblies used with jacking systems. Tube: Black, oil resistant synthetic rubber (Nitrile-Type C) Reinforcement: Two braids of high tensile steel wire. Cover: Black, oil and abrasion resistant synthetic rubber (Modified Nitrile). Available with unique abrasion-resistent MegaTuff Temperature Range: -40 C to +49 C J2AT 2 Wire Braid Jack Hose Bulk Reel J2AT / / / / / 10 J2AT / / / / / 101 MEGATUFF COVER Megatuff hose lasts up to 300 times longer than standard hose during hose-to-hose amd hose-to-metal abrasion tests per ISO 6945 J2AT-04-MTF / / / / / 10 J2AT-06-MTF / / / / / 101 Static (non-impulse) pressure rating for hydraulic jack applications only. Medium Recommended For: Medium pressure hydraulic lines. Meets or exceeds the requirements of SAE 100R1 Type AT and performance requirements of EN 853 1SN. Tube: Black, oil-resistant synthetic rubber (Nitrile-Type C) Reinforcement: One braid of high-tensile steel wire. Cover: Black, oil and abrasion resistant synthetic rubber (Modified Nitrile). Temperature Range: -40 C to +100 C Global G1 1 Wire Braid Hose - SAE 100R1 Type AT PC Fittings for -03 (except -24 and -32). GSP Fittings for -24 and -32 Bulk Reel G / / / / / 134 G / / / / / 134 G / / / / / 168 G / / / / / 11 G / / / / / 101 G / / / / / 6 G / / / / / 6 G / / / / 50 G / / / / / 30 G / / / / / 30 G / / / / 30 of Catalogue D:1-13

16 Medium Recommended For: Medium pressure hydraulic oil lines. Meets or exceeds the requirements of SAE 100R1 Type AT. Tube: Black, oil resistant synthetic rubber (Nitrile-Type C) Reinforcement: One braid of high tensile steel wire. Cover: Black, oil and abrasion resistant synthetic rubber (Hypalon - Type M). Temperature Range: -40 C to +135 C constant and +149 C intermittent (up to 10% of operating time). Global G1H High-Temp 1 Wire Braid Hose (except -24 and -32). GSP Fittings for -24 and -32 Bulk Reel G1H / / / / / 134 G1H / / / / / 11 G1H / / / / / 101 G1H / / / / / 6 G1H / / / / / 6 G1H / / / / 50 G1H / / / / / 36 G1H / / / / / 36 G1H / / / / 36 Hypalon is a registered trademark of DuPont Medium Recommended For: Low pressure power fire suppressant applications on mining and fire fighting equipment. The red cover is for easy visual identification in these applications. Tube: Black, oil resistant synthetic rubber (Nitrile-Type C) Reinforcement: One braid of high tensile steel wire. Cover: Red, oil and abrasion resistant (Modief Nitrile - Type C). Temperature Range: -40 C to +100 C. RFS Red Fire Suppressant Hose PC Fittings for -03 Bulk Reel RFS / / / / / 134 RFS / / / / / 134 RFS / / / / / 91 RFS / / / / / 91 RFS / / / / / 91 RFS / / / / 50 D:1-14 Catalogue of

17 Medium G3H (C3H) High Temp 2 Fibre Braid Hose - SAE 100R3 Recommended For: Hydraulic oil lines, anti-freeze solutions or water. Meets or exceeds the requirements of SAE 100R3. Tube: Black, synthetic rubber (Nitrile-Type C) Reinforcement: Two fibre braids. Cover: Black, oil and abrasion resistant synthetic rubber (Neoprene). Temperature Range: For hydraulic lines -40 C to +135 C constant and +149 C intermittent (up to 10% of operating time). Hose O.D. (-04, -06, -08, -10) Vacuum (in.hg / mm.hg) G3H / / / / 6 28 / / 139 G3H / / / / / / 101 G3H / / / / / / 91 G3H / / / / / / 69 G3H / / / / / / 61 G3H / / / / / / 49 G3H / / / / / 30 G3H / / / / / / 24 Medium Recommended For: Hydraulic oil lines, heavy duty transmission oil cooler lines and glycol anti-freeze solutions. Meets or exceeds the requirements of SAE 100R6. Tube: Black, specially compounded, synthetic rubber (Nitrile-Type C) Reinforcement: One fibre braids. Cover: Black, oil and abrasion resistant synthetic rubber (Neoprene). Temperature Range: For hydraulic oil lines -40 C to +135 C constant and +149 C intermittent (up to 10% of operating time). GTH (C6H) High Temp 1 Fibre Braid Hose - SAE 100R6 Hose O.D. (Except -03) PC Fittings for -03 Vacuum (in.hg / mm.hg) GTH / / / / / / 218 GTH / / / / / / 168 GTH / / / / 6 28 / / 152 GTH / / / / 6 28 / / 168 GTH / / / / / / 85 GTH / / / / / / 6 GTH / / / / / / 6 of Catalogue D:1-15

18 Low GMV - Global MegaVac Return Line and Suction Hose Recommended For: Petroleum and water-base hydraulic fluids in suction lines or on low pressure return lines. Meets or exceeds requirements of SAE 100R4. Uses half the bend radius od SAE 100R4. Tube: Black, synthetic rubber is specially designed for resistence to high temperatures (Nitrile-Type C). Reinforcement: Double spiral textile (braid for -12, -16 and -20 reinforced with a helical spiral-wire to prevent collapse. Cover: Black synthetic rubber is oil and abrasion resistant. (Neoprene - Type A). Green spiral layline. Temperature Range: -40 C to +135 C constant and +149 C intermitent (up to 10% of operating time). Hose O.D. MegaCrimp Couplings or Clamps. For -24 to -32 use GSP Couplings. For -40 to -64 use GL Couplings Vacuum (in.hg / mm.hg) GMV / / / / / / 30 GMV / / / 6 25 / / 30 GMV / / / / / / 30 GMV / / / / / / 30 GMV / / / / / 30 GMV / / / / / / 30 GMV / / 5 25 / / / / 30 GMV / / / / / 30 GMV / / / / / / 30 GMV / / / / / 30 Low Recommended For: Petroleum and water-base hydraulic fluids in suction lines or on low pressure return lines. Meets or exceeds requirements of SAE 100R4. Tube: Black, synthetic rubber is specially designed for resistence to high temperatures (Nitrile-Type C). Reinforcement: Double spiral textile reinforced with a helical spiral wire to prevent collapse. Cover: Black synthetic rubber is oil and abrasion resistant. (Neoprene). Temperature Range: For hydraulic oil lines -30 C to +100 C. Hose O.D. (mm) 100R4 Suction Hose Use clamp over beaded nipple Vacuum (in.hg / mm.hg) R / / / / / / 40 R / / / / / 40 R / / / / / / 40 R / / / / / / 40 R / 505 / / / / 40 R / / / / / / 40 R / / / / / 40 R / / / / / / 40 R / / / / / 40 D:1-16 Catalogue of

19 Low RLA 1 Fibre Braid Return Line and Low Hose Recommended For: Low pressure hydraulic oil return lines or general purpose water, glycol anti-freeze solutions, conveying diesel fuel, petrol or air. Meets 30R2 performance requirements of both Type 1 and Type 2. Tube: Black, oil resistant synthetic rubber (Nitrile - Type C) Reinforcement: One fibre braid. Cover: Black, oil and abrasion resistant synthetic rubber (Modified Nitrile). Temperature Range: -40 C to +100 C. Air to +1 C only Hose O.D. (except -3). PC Fittings (-3 only) Vacuum (in.hg / mm.hg) Bulk Reel RLA / / / / 6 28 / / 168 RLA / / / / 6 28 / / 168 RLA / / / / / / 168 RLA / / / / / / 168 RLA / / / / / / 168 RLA / / / / / / 168 RLA / / / / / / 168 RLA / / / / / 91 Low Recommended For: Petroleum-base hydraulic oils, glycol-antifreeze, air or water in low pressure fluid transfer or hydraulic system return lines. Generally connected to 100R4 stems, beaded nipples, or tube type ports with worm gear clamps Tube: Black, oil resistant synthetic rubber (Nitrile - Type C) Reinforcement: Three fibre braid. Cover: Black, oil and abrasion resistant synthetic rubber (Modified Nitrile - Type C). Temperature Range: -40 C to +135 C constant and +149 C intermittent (up to 10% of operating time). Air to +1 C only RLC 3 Fibre Braid Return Line and Low Hose Hose O.D. Fittings: Use barded stem or beaded-tube with clamps only. Vacuum (in.hg / mm.hg) RLC / / / / / 15 RLC / / / / / / 15 RLC / / / / / / 30 RLC / / / / / / 15 RLC / / / / / 15 RLC / / / / / / 15 RLC / / / / / / 15 RLC / / / / / 15 RLC / / / / / / 15 RLC / / 400 / / / / 11 of Catalogue D:1-1

20 Low LOC 1 Fibre Braid Lock-On Hose Recommended For: Petroleum-base hydraulic oils, glycol anti-freeze compounds, water, hot lubricating oils and air. Lock-On hose and fittings are not recommended for vibration or pressure surge applications, such as permanent piping in residential or commercial buildings. Tube: Black, oil resistant synthetic rubber (Nitrile - Type C) Reinforcement: One fibre braid. Cover: Oil and mildew resistant textile braid, impregnated with synthetic rubber. Temperature Range: -40 C to +100 C. For air to -40 C +1 C. Hose O.D. Fittings: Push On Field Attachable. Clamp over beaded nipple: Bulk Reel LOC / / / / 6 55 / 15 LOC / / / / / 183 LOC / / / / / 102 LOC / / / / / 9 LOC / / / / / 6 D:1-18 Catalogue of

21 of Low Recommended For: Petroleum based hydraulic oils, water, glycol antifreeze solutions, hot lubricating oils and air. Lock-On hose and fittings are NOT recommended for pressure surge applications or critical applications, such as permanent piping in residential or commercial buildings. Not recommended for gasoline or diesel fuels. Tube: Black, oil-resistant synthetic rubber highly resistent to oil and heat (Nitrile-Type C) Reinforcement: One fibre braid. Cover: Black, oil and abrasion resistant thin synthetic rubber (Modified Nitrile). Available in black-neoprene (LOLA) blue (LOLB), green (LOLG), red (LOLR), yellow (LOLY), and grey (LOLC) colours. Temperature Range: -40 C to +100 C. For air: +1 C only. Catalogue LOL Plus Lock-On Hose Fittings: Push On Field Attachable. Clamp over beaded nipple: LOL Plus Lock-On Hose is packaged in UPS shippable reels. Black is standard colour - others available on request. Vacuum (in.hg. / mm.hg) Bulk Reel LOLA / / / / 6 28 / / 91 LOLB / / / / 6 28 / / 91 LOLG / / / / 6 28 / / 91 LOLR / / / / 6 28 / / 91 LOLY / / / / 6 28 / / 91 LOLC / / / / 6 28 / / 91 LOLA / / / / 6 28 / / 91 LOLB / / / / 6 28 / / 91 LOLG / / / / 6 28 / / 91 LOLR / / / / 6 28 / / 91 LOLY / / / / 6 28 / / 91 LOLC / / / / 6 28 / / 91 LOLA / / / / 6 28 / / 91 LOLA / / / / 6 28 / / 91 LOLB / / / / 6 28 / / 91 LOLG / / / / 6 28 / / 91 LOLR / / / / 6 28 / / 91 LOLY / / / / 6 28 / / 91 LOLC / / / / 6 28 / / 91 LOLA / / / / / / 91 LOLB / / / / / / 91 LOLG / / / / / / 91 LOLR / / / / / / 91 LOLY / / / / / / 91 LOLC / / / / / / 91 LOLA / / / / / / 6 LOLB / / / / / / 6 LOLG / / / / / / 6 LOLR / / / / / / 6 LOLY / / / / / / 6 LOLC / / / / / / 6 LOLA / / / / / / 6 LOLB / / / / / / 69 LOLG / / / / / / 69 LOLR / / / / / / 69 LOLY / / / / / / 69 LOLC / / / / / / 69 D:1-19

22 PowerClean Hose Recommended For: Use on hot or cold water, high pressure cleaning equipment. Tube: Water resistant synthetic rubber. Reinforcement: High-tensile on or two wire braid. Cover: Oil resistant blue synthetic rubber. Temperature Range: -40 C to +121 C 2500 PSI Max. Burst Bulk Reel PC BLACK / / / / 91 PC BLUE / / / / PSI PC BLACK / / / / 91 PC BLUE / / / / 91 PC YELLOW / / / / PSI PC BLACK / / / / PSI PC BLACK / / / / 91 PC BLUE / / / / 91 PC BLUE / / / / PSI PC BLACK / / / / 91 PC BLUE / / / / PSI PC BLACK / / / / 91 Note: Not recommended for Steam Hose Recommended For: Use on hot or cold water, high pressure cleaning equipment. Tube: Water resistant synthetic rubber. Reinforcement: High-tensile on or two wire braid. Cover: Oil resistant blue synthetic rubber. Temperature Range: -40 C to +121 C 1 Wire Wash Hose Max. Burst Bulk Reel PW/1-04-B - 1/ / / / PW/1-05-B - 5/ / / / PW/1-06-B - 3/ / / / 12 - PW/1-08-B - 1/ / / 18-2 Wire PW/2-04-B - 1/ / / / PW/2-05-B - 5/ / / / PW/2-06-B - 3/ / / / 12 - PW/2-08-B - 1/ / / / 18 - D:1-20 Catalogue of

23 Fleet Application Recommended For: Air brake, pressurized hot oil return lines and rotary oil/air compressor lines, engine and transmission coolant lines and hot lube oil lines. Meets or exceeds DOT FMVSS 106-4, SAE J1402. Not recommended for gasoline or diesel fuel applications. Tube: True-bore black (Nitrile - Type C). Reinforcement: One braid of high tensile carbon steel wire. Cover: Oil and mildew resistant textile braid, impregnated with synthetic rubber. Temperature Range: -40 C to +149 C. Air to +1 C. TR500 Air Brake/Engine Hose Vacuum (in.hg. / mm.hg) Bulk Reel TR / / / / / / 6 TR / / / / / / 144 TR / / / / / / 122 TR / / / / 1 30 / / 91 TR / / / / / / 61 TR / / / / / 46 Fleet Application MegaTech 1000 (ACR) High-Temp Oil/Air Return and Air Brake Hose Recommended For: Air brake, pressurized hot oil return lines and rotary oil/air compressor lines. Meets the requirements of DOT FMVSS 106-4, SAE J1402, SAE J1019 performance specifications for high temperature transmission and lubricating oil systems using petroleum based oils. Not recommended for gasoline or diesel fuel applications. Tube: True-bore GTS black tube, specifically compounded for temperature and chemical resistance (CPE - Type J). Reinforcement: One braid of high tensile carbon steel wire. Cover: Oil and mildew resistant textile braid, impregnated with synthetic rubber. Temperature Range: Petroleum-base fluids -40 C to +149 C. Phosphate ester fluids as recommended by the fluid manufacturer, but within a range of -40 C to +100 C. Vacuum (in.hg. / mm.hg) Bulk Reel MT / / / / / / 10 MT / / / / / / 10 MT / / / / / / 10 MT / / / / / / 91 MT / / / / / / 61 MT / / / / / 46 MT / / / / / / 30 of Catalogue D:1-21

24 Fleet Application MegaTech 500 (ACR) High-Temp Oil/Air Return and Air Brake Hose Recommended For: Air brake, pressurized hot oil return lines and rotary oil/air compressor lines. Meets or exceeds DOT FMVSS 106-4, SAE J1402, SAE J1019 performance specifications for high temperature transmission and lubricating oil systems using petroleum base oils. Not recommended for gasoline or diesel fuel applications. Tube: True-bore GTS black tube, specifically compounded for temperature and chemical resistance (CPE - Type J). Reinforcement: One braid of high tensile carbon steel wire. Cover: Oil and mildew resistant textile braid, impregnated with synthetic rubber. Temperature Range: Petroleum-base fluids -40 C to +149 C. Phosphate ester fluids as recommended by the fluid manufacturer, but within a range of -40 C to +100 C GSP Fittings -24 and -32 GL Fittings -40 and -48 Vacuum (in.hg. / mm.hg) Bulk Carton MT / / / / / / 30 MT / / / / / 30 MT / / / / / / 30 MT / / / / / 30 Fleet Application MegaTech 250 High-Temp Transmission Oil Cooler (TOC) Hose Recommended For: For high temperature (149 C) transmission oil cooler lines, pressurised hot oil return lines, and turbo charger oil supplies. Meets or exceeds SAE J1019 performance specifications for high temperature transmission and lubricating oil systems using petroleum based oils. Not recommended for gasoline or diesel fuel applications. Tube: True-bore GTS black tube, specifically compounded for temperature and chemical resistance (CPE - Type J). Reinforcement: One braid of high tensile steel wire. Cover: Oil and mildew resistant textile braid, impregnated with synthetic rubber. Temperature Range: Petroleum-base fluids -40 C to +149 C. Phosphate ester fluids as recommended by the fluid manufacturer, but within a range of -40 C to +100 C. Vacuum (in.hg. / mm.hg) Bulk Reel MT / / / / / / 10 MT / / / / / / 10 MT / / / / / / 10 MT / / / / 6 30 / / 91 MT / / / / / / 61 MT / / / / / 46 MT / / / / / / 30 D:1-22 Catalogue of

25 Fleet Application Recommended For: Extremely High temperature petroleum based or phosphate ester fluids, turbo charger oil supply and hot lube oil lines. Meets the requirements of SAE J1405 performance specifications for high temperature transmission and lubrication oil systems. Tube: Black, oil and heat resistant synthetic polymer tube (CPE - Type J). Reinforcement: Braided high tensile wire and textile. Cover: Blue, oil and mildew resistant polyester/textile braid. Temperature Range: -40 C to +150 C. C5CXH Xtreme Heat Hose - SAE100R5 R5 Fittings Depending on sze GS Fittings Depending on Size Refer Crimp Data for Correct Selection Bulk Reel C5CXH / / / / / 11 C5CXH / / / / / 11 C5CXH / / / / / 100 C5CXH / / / / / 84 C5CXH / / / / / 66 C5CXH / / / / / 50 C5CXH / / / / / 36 of Catalogue D:1-23

26 Fleet Application Recommended For: Medium pressure hydraulic petroleum based oil lines in impulse applications, lube oil, air and water in applications such as air brakes, power steering (CAUTION: Intended for heavy-duty commercial vehicle use only), turbo charger oil supplies, tilt cab cylinders, transmission coolant and filtration lines. Meets or exceeds requirements of SAE 100R5 for traditional hydraulic applications. DOT FMVSS Type All and SAE J1402 Type All for air brake applications (-4 to -12). Not recommended for gasoline or diesel fuel. Tube: -4 and -5: black, oil and heat resistant synthetic rubber (Neoprene -m Type A); -6 through to -40. (Nitrile-Type C) Reinforcement: One braid of high tensile carbon steel wire over one braid of polyester. Cover: Black, oil and mildew resistant polyester braid. C5C SAE 100R5 Temperature Range: Under SAE 100R5 (hydraulic) conditions -40 C to +100 C. All purpose fleet application (hot lube oil lines) -40 C to +149 C. Air to +1 C only. For water emulsions, etc. Avoid continuous use at maximum temperature concurrent with maximum working pressures. Fittings: R5 Field Attachable Fittings Bulk Reel C5C / / / / / 134 C5C / / / / / 11 C5C / / / / / 11 C5C / / / / / 101 C5C / / / / / 84 C5C / / / / / 6 C5C / / / / / 50 C5C / / / / / 30 C5C / / / / / 30 C5C / / / / / 30 C5C / / / / / 30 Fleet Application Recommended For: Petroleumbase or phosphate ester fluids; diesel fuels and filtration lines, transmission coolant lines, hot lube oil lines, power steering (CAUTION: Intended for heavy-duty commercial vehicle use only), gasoline and turbocharger oil supplies. Tilt cab cylinder and air brakes. C5D (-4 to -12) meets or exceeds DOT FMVSS Type All, SAE J1402 Type All and SAE J1019 and fuel resistance of SAE J30R2. Tube: Black, oil and heat resistant synthetic rubber (CPE - Type J). Reinforcement: One braid of high tensile steel wire over one braid of polyester. Cover: Green for easy identification, oil and mildew resistant polyester braid impregnated with synthetic rubber. C5D High Temp Multifluid Hose Temperature Range: -40 C to +149 C. Air to +121 C only, maximum phosphate esters to +100 C. Fittings: R5 Field Attachable Fittings Bulk Reel C5D / / / / / 134 C5D / / / / / 11 C5D / / / / / 11 C5D / / / / / 101 C5D / / / / / 84 C5D / / / / / 6 C5D / / / / / 50 D:1-24 of Catalogue

27 Fleet Application Recommended For: On-shore/off-shore and marine diesel fuel and gasoline applications and hot lines up to 100 C. Meets marine fuel line specifications SAE J152 Type A Class I and SAE J1942 requirements. Tube: Nitrile-Type C Reinforcement: One wire braid. Cover: Modified Nitrile. Blue. Temperature Range: -20 C to +100 C. C5M Marine Fuel Line Hose Fittings: Brass or carbon steel R5 Field Attachable Fittings. Power Crimp PC stainless Permanent Fittings for marine applications. Permanent Power Crimp PC Fittings. C5M / / / / / 11 C5M / / / / / 11 C5M / / / / / 101 C5M / / / / 5 25 / 84 C5M / / / / / 6 C5M / / / / / 50 Fleet Application DOT FMVSS 106 Type AI, SAE J1019 and SAE J1402 Type AI (-4 to -12) Recommended For: Air brake hose, power steering (CAUTION: Intended for heavy-duty commercial vehicle use only), fuel filter, engine and transmission coolant lines, and hot (+149 C) lube oil lines. Not recommended for gasoline or diesel fuels. Tube: Black, oil and heat resistant, synthetic rubber (Nitrile- Type C) Reinforcement: One braid of high tensile steel wire over one braid of polyester. Cover: Black, oil and heat resistant, textile braid impregnated with synthetic rubber. Green stripe for easy identification. Temperature Range: -40 C to +149 C. Air to +121 C maximum only. C5E High Temp Flexline Hose Fittings: C5E Field Attachable Fittings. C5E / / / / / 122 C5E / / / / / 106 C5E / / / / / 68 C5E / / / / / 144 C5E / / / / / 100 C5E / / / / / 60 C5E / / / / / 84 C5E / / / / / 30 of Catalogue D:1-25

28 Fleet Application C14 Teflon Hose (SAE 100R14) Recommended For: Air compressor discharge, hot oil and fluids, hot and greasy environments. C14 Tube: Nonconductive white, smooth bore Polytetrafluroethylene (PTFE). Cover / Reinforcement: One braid of stainless steel wire. Temperature Range: -0 C to +260 C. Not recommended for high dynamic pressure loads. DN (mm) (mm) Min. / Max. Fittings: Use 2 Piece Fittings Only as specified on the Hardy Spicer teflon crimp chart. (mm) Min. / Max. TF/ / / / / / / 64 TF/ / / / / / / 6 TF/ / / / / / / 102 TF/ / / / / / / 133 TF/ / / / / / / 152 TF/ / / / / / / 18 TF/ / / / / / / 203 TF/ / / / / / 305 If used above 120 C, consider the pressure reduction factor. (Max. - Operating x Factor). Temp: 120 C, 140 C, 160 C, 180 C, 200 C, 220 C. Factor: 1.0, 0.8, 0.6, 0.4, 0.2, 0 D:1-26 Catalogue of

29 Thermoplastic TH Recommended For: Petroleum water base and synthetic hydraulic fluids. Applications include: power and telephone mobile equipment (cherry pickers), lubrication lines, blowout preventer control lines, hydraulic lifts and farm and construction machinery. TH hoses meet or exceed performance requirements of SAE 100R with a significantly tighter bend radius. Tube: 100% seamless Nylon - Type Z that easily handles a broad range of hydraulic fluids, including phosphate esters and water glycol. Reinforcement: Braided synthetic fibre on -2, -8, -12 and -16. Spiraled synthetic fibre on -3, -4, -5 and -6. Cover: Black polyurethane that resists hydraulic fluids, high temperatures, ageing and weathering. Black TH is perforated for use in general hydraulic and pneumatic service. (Black Cover) Temperature Range: -54 C to +93 C. Continuous service for petroleum and synthetic oils. Maximum of +0 C for water,/oil emulsions and water glycol. PCTS Fittings for -02 & -03 TH / / / / / 6 TH / / / / / 6 TH / / / / / 6 TH / / / / / 6 TH / / / / / 6 TH / / / / / 6 TH / / / / / 60 TH / / / / 60 Thermoplastic Recommended For: Petroleum water base and synthetic hydraulic fluids. Applications include: power and telephone mobile equipment (cherry pickers), lubrication lines, blowout preventer control lines, hydraulic lifts and farm and construction machinery. Orange colour THNC meets or exceed performance requirements of SAE 100R with a significantly tighter bend radius. Tube: -2, -12 and -16: 100% seamless nylon - Type Z that easily handles a broad range of hydraulic fluids, including phosphate esters and water glycol; -3 through to -8 polyester.. Reinforcement: Braided synthetic fibre (except -2: Spiraled synthetic fibre). Cover: Orange urethane that resists hydraulic fluids, high temperatures, ageing and weathering. Orange THNC is nonperforated for applications requiring electrical non-conductivity. Meets SAE 100R Electrical Conductivity Test. Maximum leakage shall not exceed 50 microamperes when subjected to 5 kv/ft. for five minutes. (Orange is industry accepted colour for non-conductive hose). THNC Non-Conductive - SAE100R (Orange Cover - Non-Conductive) Temperature Range: -54 C to +93 C. Continuous service for petroleum and synthetic oils. Maximum of +0 C for water,/oil emulsions and water glycol. PCTS Fittings for -02 & -03 THNC / / / / / 6 THNC / / / / / 6 THNC / / / / / 6 THNC / / / / / 6 THNC / / / / / 6 THNC / / / / / 6 THNC / / / / / 60 THNC / / / / 60 of Catalogue D:1-2

30 Thermoplastic THDL - Dual Line - SAE 100R Recommended For: Petroleum water base and synthetic hydraulic fluids. Applications include: power and telephone mobile equipment (cherry pickers), lubrication lines, blowout preventer control lines, hydraulic lifts and farm and construction machinery. THDL hoses meet or exceed performance requirements of SAE 100R with a significantly tighter bend radius. Tube: 100% seamless Nylon - Type Z that easily handles a broad range of hydraulic fluids, including phosphate esters and water glycol. Reinforcement: Spiraled synthetic fibre. Cover: Black polyurethane that resists hydraulic fluids, high temperatures, ageing and weathering. Black GTDL is perforated for use in general hydraulic and pneumatic service. (Black Cover) Temperature Range: -54 C to +93 C. Continuous service for petroleum and synthetic oils. Maximum of +0 C for water,/oil emulsions and water glycol. THDL / / / / / 6 THDL / / / / / 6 THDL / / / / / 6 THDL / / / / / 6 Thermoplastic Recommended For: Petroleum water base and synthetic hydraulic fluids. Applications include: power and telephone mobile equipment (cherry pickers), lubrication lines, blowout preventer control lines, hydraulic lifts and farm and construction machinery. Orange colour THNCDL meets SAE 100R non-conductivity requirments. THNCDL meets or exceed performance requirements of SAE 100R with a significantly tighter bend radius. Tube: Polyester. Reinforcement: Braided synthetic fibre. Cover: Orange urethane that resists hydraulic fluids, high temperatures, ageing and weathering. Orange THNCDL is non-perforated for applications requiring electrical nonconductivity. Meets SAE 100R Electrical Conductivity Test. Maximum leakage shall not exceed 50 microamperes when subjected to 5 kv/ft. for five minutes. (Orange is industry accepted colour for non-conductive hose). THNCDL Non-Conductive Dual Line SAE100R (Orange Cover - Non-Conductive) Temperature Range: -54 C to +93 C. Continuous service for petroleum and synthetic oils. Maximum of +0 C for water,/oil emulsions and water glycol. THNCDL / / / / / 6 THNCDL / / / / / 6 THNCDL / / / / / 6 D:1-28 Catalogue of

31 Thermoplastic TH8 - SAE 100R8 Recommended For: Use with petroleum, water base and synthetic hydraulic fluids. Applications include: power and telephone mobile equipment (cherry pickers), lubrication lines, blowout preventer control lines, hydraulic lifts and farm and construction equipment. TH8NC hose (orange cover) meets SAE 100R8 non-conductivity requirements. TH8 and TH8NC hoses meet or exceed performance requirements of SAE 100R8 with a significantly tighter bend radius. Multiline avaialable. Tube: 100% seamless Nylon - Type Z that easily handles a broad range of hydraulic fluids, including phosphate esters and water glycol. Reinforcement: Two polyester braids. Cover: Black or orange urethane resists hydraulic fluids, high temperatures, aging and weather. TH8NC (orange) is nonperforated for applications requiring electrical nonconductivity. TH8NC meets SAE 100R8 Electrical Conductivity Test. Maximum leakage shall not exceed 50 microamperes when subjected to 5 kv/ft. for five minutes. (Orange is industry accepted colour for non-conductive hose). Black cover is perforated for use in general hydraulic and pneumatic service. (Black Cover) Temperature Range: -54 C to +93 C. Continuous service for petroleum and synthetic oils. Maximum of +0 C for water,/oil emulsions and water glycol. (-4 through to -16) PCTS Fittings for -03 TH / / / / / 6 TH / / / / / 6 TH / / / / / 6 TH / / / / / 6 TH / / / / / 60 TH / / / / 60 Thermoplastic Recommended For: Use with petroleum, water base and synthetic hydraulic fluids. Applications include: power and telephone mobile equipment (cherry pickers), lubrication lines, blowout preventer control lines, hydraulic lifts and farm and construction equipment. GT8NC hose (orange cover) meets SAE 100R8 non-conductivity requirements. TH8 and TH8NC hoses meet or exceed performance requirements of SAE 100R8 with a significantly tighter bend radius. Multiline avaialable. Tube: 100% seamless Nylon - Type Z that easily handles a broad range of hydraulic fluids, including phosphate esters and water glycol. Reinforcement: Two polyester braids. Cover: Black or orange urethane resists hydraulic fluids, high temperatures, aging and weather. TH8NC (orange) is nonperforated for applications requiring electrical nonconductivity. TH8NC meets SAE 100R8 Electrical Conductivity Test. Maximum leakage shall not exceed 50 microamperes when subjected to 5 kv/ft. for five minutes. (Orange is industry accepted colour for non-conductive hose). Black cover is perforated for use in general hydraulic and pneumatic service. TH8NC - SAE 100R8 Temperature Range: -54 C to +93 C. Continuous service for petroleum and synthetic oils. Maximum of +0 C for water,/oil emulsions and water glycol. (-4 through to -16) (Orange Cover - Non-Conductive) TH8NC / / / / / 6 TH8NC / / / / / 6 TH8NC / / / / / 6 of Catalogue D:1-29

32 Refrigerant PolarSeal Hose (SAE J51, Type A2 Dimensions; SAE J51, Type D Performance; SAE J2064, Type C, Class II Performance) Recommended For: Liquid and gaseous R134a, R12 and R22 refrigerants in automotive air conditioning and industrial systems; i.e. tractors, construction trucks, mobile and stationary refrigeration units. Designed to minimize permeation of R134a refrigerant and contamination of the system. Tube: Black synthetic rubber. Barrier: Nylon liner. Reinforcement: Two layers of spiral polyester. Cover: Black synthetic rubber. Temperature Range: -30 C to +125 C. Permanent G45 PolarSeal (ACA) Fittings. AC134a / / / / / 104 AC134a / / / / / 2 AC134a / / / / / 64 AC134a / / / / / 53 Power Steering Recommended For: Power steering pressure lines. Designed to meet requirements of SAE J2050 specifications. Tube: Synthetic rubber specially compounded to provide resistance to high temperatures and power steering fluid (Hypalon - Type M). Reinforcement: Two high strength nylon braids that resist high temperatures and allow for expansion for system noise dampening. Cover: Black sybthetic rubber developed specifically to resist under hood environment (Neoprene). Temperature Range: -40 C to +150 C. Designed to meet requirements of SAE J2050 specifications. PS188 Power Steering Hose One piece, permanent Power Steering Fittings. PS / / / / / 15 D:1-30 Catalogue of

33 Multi-Purpose Hose Recommended For: Applications requiring a premium quality, multi-purpose hose with superior abrasion resistance for air, oil and some chemical applications. Excellent durability for extra long life in these applications.: mining, air drill, construction, poultry plants and other severe service. Excellent weather and ozone resistance. Tube: Type C (Nitrile). Black Reinforcement: Synthetic, high tensile textile cord. Cover: Type C 4 (Carboxylated Nitrile). Yellow. Temperature Range: -40 C to 100ºC continuous service. TERMINATOR - Air and Multi-Purpose Hose (Except -24 and -32) GSP Fittings for -24 and -32 TERMINATOR Vacuum (in.hg. / mm.hg) TERMINATOR / / / 6 30 / 62 TERMINATOR / / / 6 25 / 635 TERMINATOR / / / / 635 TERMINATOR / / / / 381 TERMINATOR / / / 254 TERMINATOR / / / / 254 TERMINATOR / / / / 254 TERMINATOR / / / 254 Multi-Purpose Hose Recommended For: Premo Flex is the perfect choice for multiple applications requiring a highly flexible, cost effective hose with maximum resistance to petroleum oils, gasoline, kerosene and fuel oil (to +48ºC) and lubrication oils (to +100ºC). Premo Flex can be used for transferring gasoline or diesel fuels. It is also suitable for air and water applications, offers excellent weather and ozone resistance. Tube: NBR (Nitrile). RMA (Class A) High oil resistence. Reinforcement: Synthetic, high tensile textile cord. Cover: Type C2 (Modified Nitrile). Red. Temperature Range: -40 C to 100ºC continuous service. Characteristics: Non conductive at 1000 volts DC. Meets electrical; resistance of one megaohm per inch when subjected to 1000 volts DC. PREMOFLEX - Air and Multi-Purpose Hose Fittings: Hose clamps PREMOFLEX Vacuum (in.hg. / mm.hg) PREMO / / / / 62 PREMO / / / / 62 PREMO / / / 6 30 / 62 PREMO / / / / 635 PREMO / / / / 508 PREMO / / / / 508 PREMO / / / 254 PREMO / / / / 254 PREMO / / / / 254 of Catalogue D:1-31

34 Waterblast Assemblies WB Waterblast Type: Max : Available Sizes: Liner: Reinforcement: Cover: Skive: Temperature Range: Waterblast Hose Assemblies Waterblast Hose Up to 1000bar (14500psi) -08 & -12 Synthetic rubber resistant to water, water-glycol hydraulic fluids Four spiraled layers of high tensile steel wire Oil & weather resistant black synthetic rubber Yes - Internal & External -40ºC to +85ºC (-40ºF to 185ºF) Black synthentic rubber resistant to oils, weather & abrasion. Matched to M24 x 1.5 & M36 x 1.5 Female Fittings. Solid nut type, no crimp or thrust wire nuts. Available in single hose lengths up to 40 metres. Tight bend radius 200mm (-08) 310mm (-12). All hose assemblies to be indivdually tested, certified and numbered. Cost competitve with similar products in market. All hoses are sold as a complete pressure tested and certified hose assembly. Individual parts are not available separately. Dash Size Nominal WB/PLUS /2 (12.mm) WB/PLUS /4 (19.1mm) Dash Size WBMF /2 (12.mm) WBMF /4 (19.1mm) HOSE OD Reinforcement Max. (bar / psi) Min. Burst (bar / psi) (2mm) 1.26 (32.4mm) (23mm) (29.5mm) HOSE FITTINGS Min Bend Weight 1000 / / / lb/ft (1.36kg/m) 1000 / / / lb/ft (1.80kg/m) Nominal Female Thread Ferrule External Skive Internal Skive Crimp Diameter M24 x 1.5mm WBF mm 16.0mm 29.1mm M36 x 1.5mm WBF mm 19.0mm 38.9mm D:1-32 of Catalogue