MINING PRODUCTS POWERING PROGRESS MINING PRODUCTS HYDRAULICS + INDUSTRIAL HOSE + POWER TRANSMISSION

Transcription

1 MINING PRODUCTS POWERING PROGRESS TM MINING PRODUCTS GATES CORPORATION 1551 Wewatta Street Denver, CO / Fax Gates.com/mining September 2012 Supersedes September 2008 Edition HYDRAUICS + INDUSTRIA HOSE + POWER TRANSMISSION

2 TABE OF CONTENTS Warnings and Caution... 2 Getting the Best Service ife... 3 Information Temperature imits Agency Specifications Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belt Preventive Maintenance Tools PolyChain GT Carbon Belts Super HC Belts Predator Belts Hi-Power II Belts Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 1

3 Belts Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information Avoid injury to yourself and others by following these important hose assembly steps: Never underestimate the power of a blown hydraulic assembly. WARNING Serious injury, death and destruction of property can result from rupture or blow-apart of a hydraulic hose assembly that is: Damaged or worn out Assembled or installed incorrectly 1. Receive hands-on training with Gates recommended equipment. 2. Follow current Gates operating manuals and crimp data. 3. Use only new (unused) Gates recommended hose and couplings with Gates crimpers. 4. Wear safety glasses. Select and Install Assemblies With Care 1. Select proper hose assemblies for the application. Many factors and conditions affecting the inside and outside diameter of the hose must be taken into account. 2. Hose assembly routing must not create an injury hazard or damage hose. Refer to the standards, regulations and directories that apply in the countries where the equipment is sold and used. 3. Select hydraulic components so that the application's temperature, Many factors affect the selection, making, installation and maintenance of hose assemblies. This catalog, Gates Corporation, the hydraulic equipment maker and the Society of Automotive Engineers Recommended Practice SAE J1273, have useful information about selecting, making, installing and servicing hydraulic hose pressure and bend radius do not exceed recommended component limits. 4. Hose must not be stretched, kinked, crushed or twisted during installation or use. Hose must not be bent to less than the minimum bend radius. 5. Use only thermoplastic hose for non-conductive applications. For instance: cherry pickers. All other Gates hoses are electrically conductive. 6. DO NOT use hydraulic hose to transmit high pressure gases or steam. Follow Good Maintenance Practices 1. Establish a program of inspection, testing and replacement of hose assemblies from factors including: Severity of application. Frequency of equipment use. Past performance of hose assemblies. OTHER SAFETY INFORMATION assemblies. For further information, please contact your local Gates representative or call Gates Corporation. Gates recommends hose and coupling combinations in this catalog only after completing extensive testing. Evaluation of a hose and coupling combination requires considerable impulse testing and cannot be determined by a simple burst or pressure hold test. Gates disclaims all liability for any hose assembly made in violation of Gates recommendations, procedures and current crimp data. Crimp data is updated on average every year. For the most up-to-date crimp data, visit our website at www. gates.com/ecrimp. 2. Only properly trained persons should inspect, test or service hose assemblies. Update training periodically. 3. Document maintenance, inspections and testing. 4. AVOID FUID INJECTION INJURIES Fluid under pressure can cause serious injury. It can be almost invisible escaping from a pinhole, and it can pierce the skin into the body. Do not touch a pressurized hydraulic hose assembly with any part of your body. If fluid punctures the skin, even if no pain is felt, a serious emergency exists. Obtain medical assistance immediately. Failure to do so can result in loss of the injured body part or death. 5. Stay out of hazardous areas while testing hose assemblies under pressure. Use proper safety protection. The consumer's exclusive remedy with respect to any claim shall be a refund of the purchase price or replacement of the product at the option of Gates. In no event shall Gates be liable for any incidental or consequential damages whatsoever. IMITED WARRANTY Gates s are warranted to be free from defects in material and workmanship, and Gates will, at its option, replace or repair any s proved defective in material or workmanship. This is the sole remedy for breach of warranty. A OTHER WARRANTIES, EXPRESS OR IMPIED, INCUDING, BUT NOT IMITED TO, WARRANTIES OF MERCHANTABIITY AND FITNESS FOR A PARTICUAR PURPOSE, HEREBY ARE EXPRESSY DISCAIMED. IABIITY FOR CONSEQUENTIA, INCIDENTA, SPECIA, EXEMPARY AND INDIRECT DAMAGES, INCUDING, BUT NOT IMITED TO, OST PROFITS, HEREBY IS EXPRESSY EXCUDED, REGARDESS OF WHETHER SUCH DAMAGES WERE REASONABY FORESEEABE, OR WHETHER GATES HAD KNOWEDGE THAT THEY COUD OCCUR. This imited Warranty shall be void to the extent that any of the following, as determined by Gates, occurs: (a) improper installation of the s, including any unau thorized installation of s into vehicles; (b) improper usage or maintenance of the s; (c) induction of defect by other products; (d) mishandling of the s or other abuse; (e) improper matching with other applications; (f) collision, engine overheating or oil starvation, or product misapplication or contamina tion, including, but not limited to, contamination with oil or antifreeze; (g) the s are used for racing or competition; (h) any use not recommended in writing by Gates; or (i) any failure to follow use instructions. 2 gates.com/mining Gates Corporation

4 GETTING THE BEST SERVICE IFE FROM GATES HYDRAUIC HOSE + ASSEMBIES How long will a hydraulic hose assembly last? It depends on how it's used. This catalog and other Gates literature show the recommended limits for our assemblies (and also the hoses and couplings used to make assemblies). These limits include installation, maintenance and conditions of use. These limits MUST be followed or the assembly can fail resulting in personal injury or property damage. If you do not have this important information, you can get it at no cost from your local Gates distributor or Gates field representative. Hose assemblies in use should be inspected regularly for leaks, kinks, cover blisters, gouges, abrasion and other damage. Damaged or worn assemblies must be replaced immediately. You can increase assembly life if you do the following: Hose Assembly Installation Hydraulic hose assembly installations should comply with hydraulic hose routing and plumbing standards per SAE J1273 for the proper application of hose assemblies. Working Pressure The hydraulic system pressure should not exceed the rated working pressure of the hose. Pressure surges or peaks exceeding the rated working pressure are destructive and must be taken into account when selecting a hose. Minimum Burst Pressure Burst pressures are pressures referred to in this catalog which were intended for destructive testing purposes and for design safety factors only. Temperature Range Do not expose hose to internal or external temperatures exceeding the recommended limits. Consult additional technical data when hydraulic fluids contain emulsions or solutions. The fluid manufacturer's recommended maximum operating temperature for any given fluid must not be exceeded, regardless of hose temperature range. Fluid Compatibility The hydraulic assembly (tube, cover, reinforcement and couplings) must be fluid compatible. The correct hose must be used because phosphate ester and petroleum-based hydraulic fluids have drastically different chemical characteristics. Many hoses are compatible with one or the other, but not all fluids. For example, Gates G2XH, MegaTech and C5D hoses are capable of handling phosphate ester and petroleum-based hydraulic fluids. Minimum Bend Radius Do not bend or flex hose to a radius smaller than the minimum recommended and do not subject hose to tension or torque. This can place excessive stress on the reinforcement and severely reduce the ability of the hose to withstand pressure. Hose Size Hose size (inside diameter) must be capable of handling the required flow volume. Too small an l.d. for a given volume of flow results in excessive fluid pressure and heat generation which can result in tube damage. Hose Routing Restrain, protect or guide hose, with clamps if necessary, to minimize the risk of damage due to excessive flexing, whipping or contacting other moving parts or corrosives. Determine hose lengths and configurations that protect from abrasion, snagging or kinking and provide leakresistant connections. Hose ength Correct hose length should include considerations for length changes under pressure, machine vibration and motion, and hose assembly routing. Hose Applications Select the proper hose for the application. Suction applications (Gates GMV or G4H) and special fluid or high temperature capabilities are among the applications requiring particular consideration and a specific hose. When additional information is required, contact your local Gates representative. NOTE: Do not use Gates hydraulic hose in place of permanent piping. Hose Shelf ife Storage environment, along with rubber materials can vary the shelf life limit. Shelf life is difficult to quantify as many variables affect the hose. Proper storage precautions can result in three to five years shelf life. Beyond this time there can be significant service life decrease, depending on storage environment variables. Some variables are: Temperature Hose should be stored in a cool, dry area never exceeding +100 F (+38 C). If stored below freezing, pre-warming may be required prior to handling, testing and placing into service. Direct sunlight, rain, heaters or being near electrical equipment Humidity and ozone Oil, solvents, corrosive materials or fumes Insects or rodents Radioactivity Space allowance and bends Store hose in original container. Never stack hose too high, as its weight can crush hose at the bottom of the stack. Gates recommends hose in extended storage be visually inspected and tested prior to use. Hose judged marginal should be replaced to avoid potential failure, property damage or bodily injury. Store hose on a first-in/first-out basis. Unusually long storage, or poor storage environment can deteriorate hose, reduce performance and may lead to premature failure. Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 3

5 Specialized Mining Hose Information Specialized Mining Couplings, Adapters and Accessories Constant Pressure Hoses The MegaSys line consists of constant pressure spiral-wire and wire-braid hoses that can be bent up to one-third SAE specifications. Combined with innovative couplings specifically designed to crimp on these hoses, leak-free performance is guaranteed up to maximum working pressures as high as 8,000 psi. Standard Hydraulic Hose MegaSys Benefits Equipment Belts Simplifies hose selection with constant pressure ratings Bends up to one-third SAE bend radius specifications Saves overall hose assembly length Facilitates easier routing in tight applications Requires fewer bent tube fittings Eases installation with higher flexibility owers inventory requirements Extends life in bending, flexing applications Available with abrasion-resistant XtraTuff or MegaTuff covers Reduces costs by as much as 64 percent 4 gates.com/mining Gates Corporation

6 The MegaSys Hose ine MegaSys Spiral-Wire Constant Pressure Hoses EFG3K, EFG4K, EFG5K, EFG6K and G8K Hoses Each hose features a constant working pressure Four alternating layers (six in some larger sizes) of spiraled, high tensile steel Nitrile tube for use with biodegradable hydraulic fluids Tested to industry-leading 1,000,000 impulse cycles Temperature range -40 F to +250 F (-40 C to +121 C) Available with abrasion-resistant MegaTuff cover MegaSys Wire-Braid Constant Pressure Hoses M3K, M4K, M5K and M6K Hoses Each hose features a constant working pressure Two braids of high-tensile steel wire (one braid in M3K -3, -4, -5, -6 and -8 sizes) Nitrile tube for use with biodegradable hydraulic fluids Tested to industry-leading 600,000 cycles Temperature range -40 F to +212 F (-40 C to +100 C) Available with abrasion-resistant XtraTuff or MegaTuff covers MegaSys Hose Pressure Color Key 3000 psi 4000 psi 5000 psi 6000 psi 8000 psi Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 5

7 Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information ifeguard ine-of-sight Sleeving System There's a Better Way to Protect Equipment Operators Against Hydraulic Hose Failure. A burst or pinhole leak in a hydraulic system can cause serious problems especially for anything or anyone located within a three-foot line-of-sight. Personal injury. Fluid burns and injection. Fires and explosions. Electrical shock. Mechanical failure. Now, Gates has engineered the first effective, economical alternative to costly metal shielding or rerouting of hose lines. The ifeguard sleeving system is designed to protect operators, equipment and the environment from the hazards of catastrophic hydraulic hose failure a level of protection previously unavailable. IFEGUARD SEEVE How the System Works HOSE ONY The ifeguard sleeve is slipped onto the hose and clamped at each end. If a hose burst or pinhole leak occurs, escaping pressures and fluids are contained by the exceptionally strong sleeving material. Fluids then exit the system via openings created by the specially designed channel clamps at each end. A noticeable pool of leaking fluid serves as positive verification that a failure has occurred so corrective action can be taken immediately to replace the hose assembly. ifeguard sleeving correlates to a variety of industry standards, including ISO 3457 and MSHA's flame-resistance requirements. IFEGUARD SEEVE The ifeguard sleeve contained and effectively redirected fluid during 10,000 psi (68.9 MPa) burst tests while hoses without sleeving exploded, releasing a large amount of fluid in the immediate area. Provides containment of up to 10,000 psi (68.9 MPa) bursts Protects against 5,000 psi (34.5 MPa) pinhole leaks at +212 F (+100 C) for up to five minutes Handles hydraulic fluids and biodiesel fuel Allows fluid to safely escape down the length of the assembly Creates noticeable spill for hose failure detection Correlates to ISO 3457 and meets MSHA's flameresistance requirements No other sleeve provides this level of protection Patent pending system includes Gates hose, couplings, sleeve and channel clamps HOSE ONY Belts 6 gates.com/mining Gates Corporation

8 Solid, eak-free MegaCrimp Couplings The majority of hydraulic hose failures occur at the couplings due to blow-offs or leaks. Gates has designed and engineered innovative, robust couplings for MegaSys hoses that provide connections you can count on for superior performance guaranteed. The Versatile "No-Weep" Coupling with the Patented "C" Insert It's what's inside the pre-assembled MegaCrimp coupling that gives it world-class, leak-proof performance. It is designed with a patented "C" insert, attached to the ferrule, that accommodates hoses of different constructions and wall thicknesses. The insert's design ensures crimping forces are evenly distributed to form a concentric seal. During crimping, only the MegaCrimp coupling's outside shell takes on the shape of the dies. The "C" insert starts round, stays round like the hose. The "C" insert simplifies inventory requirements since one MegaCrimp coupling size can accommodate various hose outside diameters, on both one- and two-wire braid hydraulic hoses. GlobalSpiral Couplings The no-skive coupling one stem is all you need Robust swivel joint allows for maximum torque Strong Full-Torque Nut design up to 24,000 psi burst pressure (-20 size EFG6K) with improved torque resistance Features No skive Tested to 1,000,000 impulse cycles Key Features Robust "bite-the-wire" crimp ow profile Full-stem insertion Full-length crimp Tested to industry-leading 600,000 impulse cycles Simplifies inventory management Environmentally-friendly TuffCoat plating for 500 percent better corrosion resistance Coupling to 6,000 psi working pressure in all sizes* Over 75-plus thread/flange configurations TuffCoat plating "Bite-the-wire" crimp Premium steel +250 F temperature capability Machined full-back FJX and FFORX nuts Meets worldwide DIN, EN, SAE, ISO and Gates EFG6K standards and requirements One stem used for all spiral hoses Two-piece design *Except as noted in coupling tables MegaCrimp couplings have an optimum insertion force not too tight, not too loose so you can feel them "hit bottom" when inserted. Benefits Once inserted, MegaCrimp couplings stay put. They don't fall out. Fast, tailor-made assemblies. Eliminates skiving equipment, odor and dust. Extended coupling life. Easy-to-manage inventory. Fewer SKUs. Application coverage. More than five times better corrosion resistance than SAE ASTMB117 specification. Improved coupling retention. Maximum strength. Full performance at high temperatures. onger coupling life. 4:1 burst performance up to 24,000 psi. Improved torque/sealing capability. World-class performance. ess inventory. Easier to use. Reduced inventory by 30% because only one stem is required for all spiral wire hose types. Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 7

9 Information Choose the Gates Belt that Meets Your Needs Gates offers more types of belts than ever before. This broad choice of products allows you to select the belt that provides the best performance and the best value on your mining equipment. Belts Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Predator Belts Best Belts Available for Crusher Equipment. Highest power density of any V-belt on the market. Ideal for drives requiring high-impact strength and loadcarrying power. Minimal stretch for reduced maintenance. Allows momentary belt slip to act as a mechanical fuse in the system. KEVAR * or aramid tensile cords. Predator Single Belt Wear-resistant double fabric cover. Singles belts: AP, BP, CP, 5VP & 8VP classical cross sections; SPB-P & SPC-P metric cross sections. PowerBand belts: CP (up to 12 strands), 3VP (up to 10 strands), 5VP (up to 16 strands), 8VP (up to 12 strands). Predator PowerBand Belt Single or PowerBand V-Belts? To determine whether to choose single v-belts or joined PowerBand v-belts, first identify how much rock and debris your belt guards allow into your drive systems: None to 3/8 inch debris: Use one or more single belts. arger than 3/8 inch debris: Use PowerBand belts Note: PowerBand belts should not be used on deep groove sheaves because the tie band across the top will be cut or separate from the individual belt strands. *Kevlar is a registered trademark of E.I. du Pont de Nemours and Company Other Gates Belts for Aggregate Equipment Drive Applications. Super HC Molded Notch V-Belt Shaker Screens Service up to 400 hp. EPDM construction handles temperatures from -60 to +250 F Molded notches increase flexibility for drives with smaller diameter sheaves. Single belts: 3VX, 5VX, 8VX cross sections. PowerBand belts: 3VX (up to 22 strands), 5VX (up to 13 strands). Super HC V-Belt Shaker Screens Service up to 300 hp. Single belts: 3V, 5V, 8V cross sections. PowerBand belts: 3V (up to 30 strands), 5V (up to 18 strands), 8V (up to 12 strands). Hi-Power II V-Belt Shaker Screens Good general purpose V-belt. Single belts: A, B, C, D, E cross sections. PowerBand Belts: A (up to 20 strands), B (up to 16 strands), C (up to 12 strands), D (up to 8 strands). Poly Chain GT Carbon Synchronous Belt Shaker Screens and Conveyors Clean-running, high-powered polyurethane belt drive alternative to roller chain. Carbon tensile cord combines minimal stretch with extraordinary strength and load capacity, while absorbing shock loads. Ideal for low-speed, high-torque applications. Virtually immune to abrasion. 8mm pitch 12mm to 62mm widths. 14mm pitch 20mm to 125mm widths. 8 gates.com/mining Gates Corporation

10 Resources for Drive Design & More Information Visit to access these additional tools from Gates that help you save money and time: Design Flex Pro Software: Download software to design two-point drives in minutes, and get numerous drive solutions that fit your parameters. Design Flex Web : This online program has all the functionality of Design Flex Pro. Design IQ Software: Download this program to design multi-point and complex serpentine belt drives. It calculates necessary belt tension, shaft load, belt length and more. PartView : ocate the belts, sprockets and sheaves you need in this catalog complete with CAD models and 2D specification sheets. Case Studies: Improved reliability. Reduced downtime. ess maintenance. Read about the benefits of Gates belt drive systems. Gates PT Toolkit mobile app: Use your iphone or Android device to crunch the numbers on energy savings, center distance and belt tension. Perform power transmission calculations on the go. Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 9

11 Information Specialized Mining Hose Exclusive QUICK-PIC and AIM Programs Building Better Inventory Support for Construction Equipment Owners Gates Construction Distributors have instant access to our exclusive QUICK-PIC and AIM computer programs and extensive, up-to-date global product data online. Whether it's a critical failure in the field or regular equipment maintenance in the shop, your Gates Construction Distributor is the one-stop source for all your hydraulic assembly replacement needs. Complete equipment coverage Accurate, quality parts replacement Alternative to high-priced, hard-to-get OEM parts Fast, just-in-time service Minimal equipment downtime Reduced inventory costs Gates trust, quality and reliability in every assembly Specialized Mining Couplings, Adapters and Accessories Quick Part Number Interchange Finds the right replacement assembly in seconds to get equipment back on the job fast. QUICK-PIC interchanges more than 140,000 construction equipment manufacturer's part numbers with the right, high-quality Gates replacement. Your Gates Construction Distributor can then fabricate a replacement assembly to the right hose length in minutes, including fittings and protectors. Accurate Inventory Manager Matches hose and connector inventory to your equipment. With AIM, you get the parts you need, when you need them, at a price you can afford. AIM matches your Gates Construction Distributor's inventory to your exact equipment needs by manufacturer and model. No more guesswork. No more shopping around for a part. AIM tells your distributor exactly what parts to stock. Belts Equipment Standard Hydraulic Hose 10 gates.com/mining Gates Corporation

12 TEMPERATURE IMITS Temperature imits For Gates Hydraulic Hoses Caution: Water, water/oil emulsions and water/glycol solutions must be kept below the temperatures listed in the table below, relative to line pressures. Maximum Temperature imits for Water, Water/Oil Emulsions and Water/Glycol Solutions Hose G8K, EFG6K, EFG5K, EFG4K, EFG3K, G2, G2, MCPB, G1, M2T, M6K, M5K, M4K, M3K, RFS, RA, C5C, C5E, CPS, OC, O G2H, G1H, MegaTech hose line, G2XH, C5D, G3H, GTH, G4H, GMV, RC, TR500, PowerClean, M3KH, M4KH Caution: The fluid manufacturer's recommended maximum operating temperature for any given fluid must not be exceeded. If different than the above listed hose temperatures, the lower limit must take precedence. Actual service life at temperatures approaching the recommended limit will depend on the particular application and the fluid being used in the hose. Intermittent (up to 10% of operating time) refers to momentary temperature surges. Detrimental effects increase with increased exposure to elevated temperatures. Do NOT expose hose to maximum temperature and maximum rated working pressure at the same time. Agency and Industry Hose, Coupling & Assembly Specifications ABS American Bureau of Shipping AS 2260 Australian Standard BV Bureau Veritas (Marine Division), International DNV Det Norske Veritas (North Sea Floating Vessels), International DIN Deutsch Industry Norm, International G Germanischer loyd's, International IJS Industrial Jack Specifications, USA R loyd's Register, International RCCC Regular Common Carrier Conference for fleet Truck & Bus, USA DOT Department of Transportation, USA FMVSS Federal Motor Vehichle Safety Standard, USA MSHA 2G Mine Safety & Health Administration, USA FRAS Fire Retardant Anti Static, Australia USCG United States Coast Guard ISA International Standards Organization SAE Society of Automotive Engineers EN European Norm Pressure ines +200 F (+93 C) +225 F (+107 C) Return ines +180 F (+82 C) +180 F (+82 C) Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 11

13 AGENCY SPECIFICATIONS Belts Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information Gates Hose Type ABS Agency Specifications AS DOT / MSHA BV DNV DIN G IJS R RCCC FRAS 2260 FMVSS 2G USCG J1942 Fuel Oil Power Industry Specifications (PSI Performance) SAE ISO EN EFCPS X X Gates Proprietary Design EFW X X Gates Proprietary Design W X X Gates Proprietary Design CPB X X Gates Proprietary Design 100MP/Mine Spray X X Gates Proprietary Design Scorpion Gates Proprietary Design Rock Dust X X Gates Proprietary Design 18MB Gates Proprietary Design 500MP X X Gates Proprietary Design G8K X Gates Proprietary Design EFG6K X X X X X X X X X X 100R R15 EN 856 4SP/4SH EFG5K X X X X X X X X X X 100R R13 EN 856 4SP/4SH EFG4K X X X X X X X X X X 100R R12 EN 856 4SP++ EFG3K X X X X X X X X X X 100R R12 EN 856 4SP M-XP X X Gates Proprietary Design M2T X X X X X 100R SC R SC CM2TD X X X X X 100R SC R SC M6K X X X X X X Gates Proprietary Design M5K X X X X X X X Gates Proprietary Design M4K X X X X X X X X X X 100R R19 M4KH X X X X 100R R19 M3K X X X X X X X X X X X 100R R17 M3KH X X X X 100R R17 G2 X x X X X X x X X X 100R2 S SN R SN G2H X X X X X X X 100R2 S SN R SN G2XH X X X X 100R2 S SN R SN G2 X X X 100R2 S SN R SN J2AT X X X Gates Proprietary Design G1 X X X X X X X X X X 100R1 S SN R SN G1H X X X X X* X 100R1 S SN R SN RFS X X Gates Proprietary Design G3H X 100R3 854 R3 GTH X 100R6 854 R6 GTHX X 100R6 854 R6 G4H X X X 100R4 GMV X X X X X 100R4 RA X 30R2 RC Gates Proprietary Design OC 30R7 O X Gates Proprietary Design & -16 EFG4K *G1H sizes -6, -8, -12 & -16 **TH7NC Meets ANSI A92.2 for vehicle mounted aerial devices (-3 to -8) *** Needs fire sleeve when it is used for ABS application **** OA Black cover only 12 gates.com/mining Gates Corporation

14 Agency Specifications Industry Specifications (PSI Performance) Gates Hose Type ABS AS DOT / MSHA USCG J1942 BV DNV DIN G IJS R RCCC FRAS 2260 FMVSS 2G Fuel Oil Power SAE ISO EN TR500 X J1402 MegaTech II 100R2 AT, J1405 part 5 MegaTech G5TB J1405 part 6 MegaTech 3000 J1405 part 6 MegaTech 1000 X J1405 part 6, J1402 MegaTech 500 J1405 part 6 MegaTech 250 J1405 part 6 MegaTech OC J1405 part 6 C5C X X 100R5, J1402 C5D X X 100R5, J1402, J1405 C5M X X X X 100R5, J1527 A C5E X X 100R5, J1402 C14 100R14 TH7, TH7NC** 100R TH8, TH8NC 100R TH18, TH18NC 100R PolarSeal AC134a J51 "A2 & D", J2064 "C", Class 2 PolarSeal ACC-PSII J2064 "C", Class & -16 EFG4K *G1H sizes -6, -8, -12 & -16 **TH7NC Meets ANSI A92.2 for vehicle mounted aerial devices (-3 to -8) *** Needs fire sleeve when it is used for ABS application **** OA Black cover only Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 13

15 SPECIAIZED MINING HOSE Information EF Coal Power/ongwall Mine Hose EFCPS Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Min. Burst MBR Description Number (in) (in) (Max.psi) 1 (Max.psi) 2 Pressure (psi) (in) 12EFCPS / , EFCPS , EFCPS / , EFCPS / , EFCPS / , EFCPS / , EFCPS , EFCPS , Meets or exceeds SAE, ISO pressure requirements and EN 856 4SH dynamic working pressure. 2 Static working pressure means very little pressure surging as, for example, in longwall internal hydraulic roof support systems. Meets Flame Resistance Acceptance Designation "MSHA 2G" High-pressure hydraulic lines in longwall mining equipment and roof-support systems; petroleum-based or water emulsion fluids. Meets pressure requirements of EN 856 4SH. Available in cut length and/or 121' to 200' continuous lengths. Black, oil resistant, synthetic rubber (Nitrile). Four layers of alternated, spiraled, high-tensile steel wire over a layer of fabric on -12 and -16 sizes - six layers of alternated, spiraled, high-tensile steel wire over a layer of fabric on -20, -24 and -32 sizes. Black, oil and abrasion resistant, synthetic rubber (Neoprene). Yellow layline stripe. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GSH and GSM Couplings (-24 and -32) GlobalSpiral Couplings (-12, -16 and -20) Gates Proprietary Hose: Superior to SAE and ISO Specifications. Belts Equipment Standard Hydraulic Hose 14 gates.com/mining Gates Corporation

16 EF Coal Power/ongwall Mine Hose - MegaTuff EFCPS-MTF Min. Burst MBR Description Number (in) (in) (Max.psi) 1 (Max.psi) 2 Pressure (psi) (in) 12EFCPS-MTF / EFCPS-MTF EFCPS-MTF / EFCPS-MTF / EFCPS-MTF Meets or exceeds SAE, ISO and EN 856 4SH dynamic working pressure. 2 Static working pressure means very little pressure surging as, for example, in longwall internal hydraulic roof support systems. Meets Flame Resistance Acceptance Designation "MSHA 2G" High-pressure hydraulic lines in longwall mining equipment and roof-support systems; petroleum-based or water emulsion fluids. Meets pressure requirements of EN 856 4SH. Available in cut lengths. Black, oil resistant, synthetic rubber (Nitrile). Four layers of alternated, spiraled, high-tensile steel wire over a layer of fabric on -12 and -16 sizes - six layers of alternated, spiraled, high-tensile steel wire over a layer of fabric on -20, -24 and -32 sizes. Black, oil and abrasion resistant MegaTuff cover with synthetic rubber (Neoprene Type A base) with yellow color layline. Also available in standard cover. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GSH and GSM Couplings (-24 and -32) GlobalSpiral Couplings (-12, -16 and -20) Gates Proprietary Hose: Superior to SAE and ISO Specifications. Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 15

17 SPECIAIZED MINING HOSE Information EF ongwall Mine Hose EFW Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Min. Burst MBR Description Number (in) (in) (Max.psi) 1 (Max.psi) 2 Pressure (psi) (in) 8EFW / EFW / EFW EFW / EFW / EFW Impulse pressure rating. 2 Static working pressure means very little pressure surging as, for example, in longwall internal hydraulic roof support systems. Meets Flame Resistance Acceptance Designation "MSHA 2G" High-pressure hydraulic lines in longwall mining equipment and roof-support systems; petroleum-based or water emulsion fluids. Available in 121' to 200' continuous lengths. 12EFW meets the static pressure requirements of longwall mining equipment. 16EFW meets pressure requirements of longwall mining equipment and EN 856 4SP. Black, oil resistant, synthetic rubber (Nitrile). Four layers of alternated, spiraled, high-tensile steel wire over a layer of fabric. Black, oil and abrasion resistant, synthetic rubber (Neoprene). Yellow color layline stripe. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings (-12, -16 and -20) GSP (-24 and -32) Gates Proprietary Hose: Superior to SAE and ISO Specifications. Belts Equipment Standard Hydraulic Hose 16 gates.com/mining Gates Corporation

18 EF ongwall Mine Hose - MegaTuff Min. Burst MBR Description Number (in) (in) (Max.psi) 1 (Max.psi) 2 Pressure (psi) (in) 12EFW-MTF / EFW-MTF EFW-MTF / EFW-MTF / EFW-MTF Impulse pressure rating. EFW-MTF 2 Static working pressure means very little pressure surging as, for example, in longwall internal hydraulic roof support systems. Meets Flame Resistance Acceptance Designation "MSHA 2G" High-pressure hydraulic lines in longwall mining equipment and roof-support systems; petroleum-based or water emulsion fluids. Available in cut lengths. 12EFW meets the static pressure requirements of longwall mining equipment. 16EFW meets pressure requirements of longwall mining equipment and EN 856 4SP. Black, oil resistant, synthetic rubber (Nitrile). Four layers of alternated, spiraled, high-tensile steel wire over a layer of fabric. Black, oil and abrasion resistant MegaTuff cover with synthetic rubber (Neoprene Type A base) with yellow color layline. Also available in standard cover. Temperature Range: - 40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings (-12, -16 and -20) GSP (-24 and -32) Gates Proprietary Hose: Superior to SAE and ISO Specifications. Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 17

19 SPECIAIZED MINING HOSE Information Coal Power/ongwall Mine Hose - CPB Mine Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Min. Burst MBR Description Number (in) (in) (Max.psi) 1 (Max.psi) 2 Pressure (psi) (in) 4CPB / CPB / CPB / CPB / CPB CPB / CPB / CPB This working pressure per BCS174 means frequent pressure surges. Qualification testing requires 100,000 impulse cycles at 133% of the dynamic working pressure. 2 This working pressure means very little pressure surging. BCS174 says that the internal hydraulic circuit of a roof support system represents an almost steady-state condition with little or no dynamic loading, and hoses consequently will tolerate higher ratings. Determined by EN 853 2SN, it is the allowable working pressure under static load that approximates a 1:2.5 ratio to burst pressure. This is based on the EN specification burst pressures and not the higher Gates minimum burst pressures listed above. Meets Flame Resistance Acceptance Designation "MSHA 2G" Meets performance of British Coal Specification BCS174 High-pressure hydraulic lines in longwall mining equipment and roof-support systems; petroleum-based or water emulsion fluids. Black, oil resistant, synthetic rubber (Nitrile). Two braids of high-tensile steel wire. Black, oil and abrasion resistant, synthetic rubber (Nitrile). White color layline. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): MegaCrimp Couplings (-4, -6, -8, -12, -16 and -20) GSP (-24 and -32) Gates Proprietary Hose: Superior to SAE and ISO Specifications. Belts Equipment Standard Hydraulic Hose 18 gates.com/mining Gates Corporation

20 Coal Power/ongwall Mine Hose - CPB Mine - MegaTuff Min. Burst MBR Description Number (in) (in) (Max.psi) 1 (Max.psi) 2 Pressure (psi) (in) 4CPB-MTF / CPB-MTF / CPB-MTF / CPB-MTF / CPB-MTF CPB-MTF / CPB-MTF / CPB-MTF This working pressure per BCS174 means frequent pressure surges. Qualification testing requires 100,000 impulse cycles at 133% of the dynamic working pressure. 2 This working pressure means very little pressure surging. BCS174 says that the internal hydraulic circuit of a roof support system represents an almost steady-state condition with little or no dynamic loading, and hoses consequently will tolerate higher ratings. Determined by EN 853 2SN, it is the allowable working pressure under static load that approximates a 1:2.5 ratio to burst pressure. This is based on the EN specification burst pressures and not the higher Gates minimum burst pressures listed above. Meets Flame Resistance Acceptance Designation "MSHA 2G" Meets performance of British Coal Specification BCS174 High-pressure hydraulic lines in longwall mining equipment and roof-support systems; petroleum-based or water emulsion fluids. Black, oil resistant, synthetic rubber (Nitrile). Two braids of high-tensile steel wire. Black, oil and abrasion resistant MegaTuff cover with synthetic rubber (Neoprene Type A base). Also available in standard cover. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): MegaCrimp Couplings (-4, -6, -8, -12, -16, -20) GSP (-24 and -32) Gates Proprietary Hose: Superior to SAE and ISO Specifications. Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 19

21 SPECIAIZED MINING HOSE Information Air and Multi-Purpose Hose TERMINATOR Terminator (Specification 3202T, 3202TW) Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Reel Packaging Max. Suction MBR Weight Std. Number WP (in. Hg) (in) Pack / Reel / Reel / Reel / Reel Reel / Reel / ft ft ft. Exact ength 500 Foot One Piece Reels Max. Suction MBR Weight Std. Number WP (in. Hg) (in) Pack / Reel / Reel / Reel / Reel Standard Hydraulic Hose Equipment Belts Meets Flame Resistance Acceptance Designation "MSHA 30 CFR-18.65" Applications requiring a premium-quality, multi-purpose hose with superior abrasion resistance for air, oil and some chemical applications. Excellent durability for extra long life in these applications: mining, air drill, construction and other severe service. Good weather and ozone resistance. Temperature: -40 F to +212 F (-40 C to +100 C) continuous service. Construction Type C (Nitrile). Black. Construction Synthetic, high tensile textile cord. Construction Type C4 (Carboxylated Nitrile). Yellow. Packaging: 1/4" through 3/4": Packaged in 500' to 700' reels. Maximum 2 pieces in 50' increments. 1" and 1 1/4": Packaged in 300' to 400' reels. Maximum 3 pieces. Minimum length 50'. 1 1/2" and 2": Packaged 100' coiled and wrapped in polyethylene. Minimum of 90% of hose reels will be 1-piece lengths. Exact length reels: 500' in one continuous length or E-crimp): MegaCrimp couplings (through 1 1/4") GX Couplings (through 1 1/4") GSP Couplings (1 1/2" and 2" only) 20 gates.com/mining Gates Corporation

22 Air and Multi-Purpose Hose Standard Reel Packaging Exact ength 500 Foot One Piece Reels PREMOFEX AR Premo Flex AR (Specification 3205AR) Max. Suction MBR Weight Std. Number WP (in. Hg) (in) Pack / Reel / Reel / Reel / Reel Reel Max. Suction MBR Weight Std. Number WP (in. Hg) (in) Pack / / / / Meets Flame Resistance Acceptance Designation "MSHA 30 CFR-18.65" Applications requiring a premium grade spiral hose with superior abrasion resistance, excellent flexibility and maximum resistance to air, water, petroleum oils and lubricating oils (to 212 F). Recommended for gasoline, kerosene, and fuel oil transfer only to 120 F. Good weather and ozone resistance. Temperature: -40 F to +212 F (-40 C to +100 C) continuous service. Construction Type C (Nitrile). Black. Construction Synthetic, high tensile textile cord. Construction Type C4 (Carboxylated Nitrile). Red. Packaging: 1/4" through 3/4": Packaged in 500' to 700' reels. Maximum 2 pieces in 50' increments. 1": Packaged in 300' to 400' reels. Maximum 2 pieces in 50' increments. Minimum of 90% of hose reels will be 1-piece lengths. Exact length reels: 500' in one continuous length or E-crimp): MegaCrimp Couplings GX Couplings Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 21

23 SPECIAIZED MINING HOSE Information Mining Hose 1000 MP/MINE SPRAY 1000 MP/Mine Spray (Specification 3619M) Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Max. Suction MBR Weight Std. Number WP (in. Hg) (in) Pack / ft / ft ft / ft / ft ft / ft / ft ft / ft / ft ft / Bulk 50 ft / Bulk 50 ft Bulk 50 ft / Bulk 50 ft / Bulk 50 ft Bulk 50 ft / Bulk 100 ft Bulk 100 ft / Bulk 100 ft / Bulk 100 ft. Standard Hydraulic Hose Equipment Belts Meets Flame Resistance Acceptance Designation "MSHA 30 CFR-18.65" High-pressure water service in underground mining applications and hot water washdown service. Temperature: -40 F to +212 F (-40 C to +100 C) service range. Construction Type P (EPDM). Black. Construction Braided, high tensile steel wire. Construction Type C2 (Modified Nitrile). Yellow (non-marking). All sizes are perforated. Packaging: 1/2" through 2": 50' and 100' lengths, one length coiled in a carton. 1/2" x 50': Packaged 1200' per bulk carton, each length coiled and tied. 3/4" x 50': Packaged 1000' per bulk carton, each length coiled and tied. 3/4" x 100': Packaged 500' per bulk carton, each length coiled and tied. 1" x 50': Packaged 700' per bulk carton, each length coiled and tied. 1" x 100': Packaged 400' per bulk carton, each length coiled and tied. 1 1/4" x 50': Packaged 600' per bulk carton, each length coiled and tied. 1 1/4" x 100': Packaged 300' per bulk carton, each length coiled and tied. 1 1/2" x 50': Packaged 400' per bulk carton, each length coiled and tied. 1 1/2" x 100': Packaged 200' per bulk carton, each length coiled and tied. 2" x 50': Packaged 200' per bulk carton, each length coiled and tied or E-crimp): MegaCrimp (1/2" through 1 1/4") GSP (1 1/2" and 2" only) 22 gates.com/mining Gates Corporation

24 Mining Hose Black Cover (3619MC) ongwall Mine Emulsion (Specification 3619MC, 3619MY) Max. Suction MBR Weight Std. Number WP (in. Hg) (in) Pack / ft ft / ft ft. Yellow Cover (3619MY) ONGWA MINE EMUSION Max. Suction MBR Weight Std. Number WP (in. Hg) (in) Pack ft ft. Meets Flame Resistance Acceptance Designation "MSHA 30 CFR-18.65" Flexible connections in high pressure water distribution and emulsion systems used in a variety of industries. The thick cover meets MSHA's self-extinguishing requirements, and is designed for the rough mining environment. Temperature: -40 F to +212 F (-40 C to +100 C) normal service. Construction Type A (Neoprene). Black. Construction Braided, high tensile steel wire. Construction Type C2 (Specially Compounded Elastomer). Black. Type C4 (Modified Nitrile). Yellow (non-marking). Packaging: All lengths coiled in a carton. Wildman Reusable Male Dixon Holedell Style 2 1/2 W (see Crimp Data Manual or ecrimp for details) Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 23

25 SPECIAIZED MINING HOSE Information Mining Hose SCORPION Scorpion (Specification 3618MT) Specialized Mining Hose Max. Suction MBR Weight Std. Number WP (in. Hg) (in) Pack / ft ft / ft ft ft. Meets Flame Resistance Acceptance Designation "MSHA 30 CFR-18.65" High-pressure and high temperature air hose used on industrial, construction, pneumatic mining and drilling applications requiring a wire braided hose with a high degree of hot air resistance. Temperature: -40 F to +300 F (-40 C to +149 C). Construction Type J (CPE). Black. Construction Braided, high tensile steel wire. Construction Type J (CPE). Black. All sizes perforated. Packaging: 50' per carton +/- 10'. Maximum of 2 pieces. Minimum length 10' or E-crimp): GSP (-24 and -32) Belts Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories 24 gates.com/mining Gates Corporation

26 Mining Hose 18MB AIR DRI 18MB Air Drill (Specification 3618, 3618G) Max. Suction MBR Weight Std. Number WP (in. Hg) (in) Pack / ft ft / ft / ft ft ft / ft / ft ft ft. Meets Flame Resistance Acceptance Designation "MSHA 30 CFR-18.65" Extra heavy duty, high pressure use on industrial, construction and pneumatic mining applications requiring wire braided hose with an oil resistant tube and abrasion resistant cover. Temperature: -30 F to +212 F (-34 C to +100 C) continuous service. Construction Type A (Neoprene). Black. Construction Braided, high tensile steel wire. Construction Type C2 (Modified Nitrile). Gray with yellow stripe. All sizes are perforated. For 3/4" through 1 1/4" sizes only. Type D3 (Natural Rubber). Gray with yellow stripe. All sizes are perforated. For 1 1/2" through 4" sizes only. Packaging: 3/4" through 1 1/2": Packaged 49' - 50' length coiled in carton. 2" though 4": Packaged 48' - 50' length coiled in carton. 2 1/2" x 60': Packaged 60' length coiled in carton or E-crimp): GSP (1 1/2" and 2") Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 25

27 SPECIAIZED MINING HOSE Information Mining Hose 500 MP AIR DRI 500 MP Air Drill (Specification 3618, 3618Y) Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Black Cover (3618) Max. Suction MBR Weight Std. Number WP (in. Hg) (in) Pack / ft ft / ft / ft ft / ft ft. Yellow Cover (3618Y) Max. Suction MBR Weight Std. Number WP (in. Hg) (in) Pack / ft ft / ft / ft ft / ft ft. Standard Hydraulic Hose Meets Flame Resistance Acceptance Designation "MSHA 30 CFR-18.65" Heavy-duty, high pressure use on industrial, construction and pneumatic mining applications requiring wire braided hose with an oil resistant tube and abrasion resistant cover. Temperature: -22 F to +180 F (-30 C to +82 C) continuous service. Construction Type C (Nitrile). Black. Construction Braided, high tensile steel wire. Construction Type D3 (Natural Rubber). Black with yellow spiral stripe. All sizes are perforated. Type C2 (Modified Nitrile). Yellow with black spiral stripe. All sizes are perforated. Packaging: 100' length coiled in a carton or E-crimp): GSP (-24 and -32) Belts Equipment 26 gates.com/mining Gates Corporation

28 Mining Hose Rock Dust (Specification 4691) Max. Suction MBR Weight Std. Number WP (in. Hg) (in) Pack / ft / ft ft / ft ft. Meets Flame Resistance Acceptance Designation "MSHA 30 CFR-18.65" Rock dusting applications in underground coal mines where limestone dust (or other inert rock-derived dusting agent) is sprayed in order to isolate exposed coal surfaces from potential heat or ignition sources. Temperature: -40 F to +180 F (-40 C to +82 C). Construction Type D (Natural Rubber). Black. Construction Synthetic, high tensile textile with steel wire helix. Construction Type C2 (Modified Nitrile). Black with yellow spiral stripe. Packaging: 100' length coiled and wrapped in polyethylene : Multiple - contact Gates PA Hotline for additional information Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 27

29 SPECIAIZED MINING COUPINGS, ADAPTERS AND ACCESSORIES Information GlobalSpiral High Press-ok Super - Male Couplings Press-ok Couplings Hose ID ength Cutoff Description Number (in) (in) (in) 24GSH-24PSOR / GSH-32PSOR C Specialized Mining Hose GlobalSpiral Press-ok Super - Male Couplings Hose ID ength Cutoff Description Number (in) (in) (in) 8GS-8PSOR / GS-12PSOR / GS-16PSOR GS-20PSOR / C Specialized Mining Couplings, Adapters and Accessories GlobalSpiral High Press-ok Super - Male Couplings With Hammer Flange Hose ID ength Cutoff Description Number (in) (in) (in) 24GSH-24PSORHF / GSH-32PSORHF GSM-32PSORHF Includes O-rings and back-up rings. GlobalSpiral Press-ok Super - Male Couplings With Hammer Flange Hose ID ength Cutoff Description Number (in) (in) (in) 20GS-20PSORHF / Includes O-rings and back-up rings. GlobalSpiral High Press-ok Super - Female Couplings Hose ID ength Cutoff Description Number (in) (in) (in) 24GSH-24FPS / GSH-32FPS C C C Standard Hydraulic Hose GlobalSpiral Press-ok Super - Female Couplings Hose ID ength Cutoff Description Number (in) (in) (in) 8GS-8FPS / GS-12FPS / GS-16FPS GS-20FPS / GSP-24FPS / GSP-32FPS C Equipment Belts GlobalSpiral Press-ok - Male Couplings Hose ID ength Cutoff Description Number (in) (in) (in) 6GS-6P / GS-8P / GS-12P / GS-16P GS-20P / GSP-24P / GSP-32P Meets or exceeds SAE J1467. Includes O-rings and back-up rings. C 28 gates.com/mining Gates Corporation

30 MegaCrimp Press-ok - Male Couplings Press-ok Couplings Hose ID ength Cutoff Description Number (in) (in) (in) 4G-4P / G-6P / G-6P / G-8P / G-12P / G-16P G-20P / Meets or exceeds SAE J1467. Includes O-rings and back-up rings. GlobalSpiral Press-ok - Female Couplings Hose ID ength Cutoff Description Number (in) (in) (in) 32GSP-32FP Meets or exceeds SAE J1467. GlobalSpiral Press-ok ow-profile - Male Couplings Hose ID ength Cutoff Description Number (in) (in) (in) 24GSP-24PM / GSP-32PM Includes O-rings and back-up rings. GlobalSpiral Press-ok ow-profile - Female Couplings Hose ID ength Cutoff Description Number (in) (in) (in) 24GSP-24PF / GSP-32PF ongwall Mine Emulsion Hose coupling Press-ok ow-profile - Male Coupling C Description Number (mm) (mm) 40W-40PM ongwall Mine Emulsion Hose coupling Press-ok ow-profile - Female Coupling C Description Number (mm) (mm) 40W-40PF ongwall Mine Emulsion Hose Ferrule Description Number (mm) 40W1F C C C C C C Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 29

31 SPECIAIZED MINING COUPINGS, ADAPTERS AND ACCESSORIES Information Specialized Mining Hose Press-ok Super Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Male Press-ok Super to Female Press-ok C T1 Description Number (mm) (in) (mm) 20MSH-6FSA / MSH-12FSA / MSH-16FSA / MSH-20FSA / MSH-24FSA / MSH-32FSA / MSH-16FSA / MSH-20FSA / MSH-32FSA / MSH-20FSA MSH-24FSA T1 C Belts Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Male Press-ok Super to Female Press-ok Super Straight C T1 Description Number (mm) (in) (mm) 20MSH-20FSH / MSH-20FSH / Male Press-ok Super to Female Press-ok Super - 45 T1 A Description Number (in) (mm) (mm) 8MSH-8FSH / MSH-12FSH / MSH-16FSH Male Press-ok Super to Female Press-ok Super - 90 T1 A Description Number (in) (mm) (mm) 12MSH-12FSH / MSH-16FSH MSH-20FSH / MSH-24FSH / Female Press-ok Super to Female Press-ok Super Straight Reference Coupling A Description Number (in) (mm) (mm) 8FSH-8FSH /2-1/ FSH-12FSH /4-3/ FSH-16FSH FSH-20FSH /4-1 1/ FSH-24FSH /2-1 1/ FSH-32FSH Female Press-ok Super Y A Description Number (mm) (mm) FSHY FSHY T1 T1 T1 A A T1 A C T1 A 30 gates.com/mining Gates Corporation

32 Press-ok Super Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Female Press-ok Super to Female Press-ok Super - 90 Reference Coupling A Description Number (in) (mm) (mm) 8FSH-8FSH /2-1/ FSH-12FSH /4-3/ FSH-16FSH FSH-20FSH /4-1 1/ FSH-24FSH /2-1 1/ FSH-32FSH Female Press-ok Super Tee Reference Coupling A B Description Number (in) (mm) (mm) (mm) 8-8-8FSHT /2-1/2-1/ FSHT /4-3/4-3/ FSHT FSHT /4-1 1/4-1 1/ FSHT /2-1 1/2-1 1/ FSHT /2-1 1/2-1 1/ FSHT / FSHT Female Press-ok Super to NPTF Solid Male A T1 Description Number (mm) (in) Thread (mm) 8FSH-8MP /2 1/ FSH-12MP /4 3/ FSH-16MP / FSH-20MP /4 1 1/4-11 1/ FSH-24MP /2 1 1/2-11 1/ FSH-32MP / Female Press-ok Super to Female Press-ok Super Ball Valve Reference Coupling A Description Number (in) (mm) (mm) 20FSH-20FSHBV /4-1 1/ FSH-24FSHBV /2-1 1/ FSH-32FSHBV Male Press-ok Super Plug T1 Description Number (in) (mm) 8MSH-PUG / MSH-PUG / MSH-PUG MSH-PUG / MSH-PUG / MSH-PUG A B A T1 T1 A B A Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 31

33 SPECIAIZED MINING COUPINGS, ADAPTERS AND ACCESSORIES Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Press-ok Super Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Male Press-ok Super to NPTF Solid Male T1 Description Number (in) Thread (mm) 8MSH-8MP /2 1/ MSH-12MP /4 3/ MSH-16MP / MSH-20MP /4 1 1/4-11 1/ MSH-24MP /2 1 1/2-11 1/ MSH-32MP / Male Press-ok Super to Male Press-ok A B T1 T2 Description Number (mm) (mm) (in) (in) (mm) 20MSH-24MSA /4 1 1/ Male Press-ok Super to Male Press-ok Super A B T1 T2 Description Number (mm) (mm) (in) (in) (mm) 12MSH-12MSH /4 3/ MSH-12MSH / MSH-12MSH /4 3/ MSH-16MSH / MSH-20MSH /4 1 1/ MSH-24MSH /4 1 1/ MSH-32MSH / MSH-20MSH /2 1 1/ MSH-24MSH /2 1 1/ MSH-20MSH / MSH-24MSH / MSH-32MSH T1 T1 T1 A A B B T2 T2 Female Press-ok Super Cap A T1 Description Number (mm) (in) (mm) 8FSH-CAP / FSH-CAP / FSH-CAP FSH-CAP / FSH-CAP / FSH-CAP A T1 Belts Equipment Standard Hydraulic Hose 32 gates.com/mining Gates Corporation

34 Staple Reference Coupling Description Number (in) 8SHS STAPE /2 12SHS STAPE /4 20SHS STAPE /4 24SHS STAPE /2 32SHS STAPE O-Ring Reference Coupling Description Number (in) 8 SHOR O-RING /2 12 SHOR O-RING /4 16 SHOR O-RING SHOR O-RING /4 24 SHOR O-RING /2 32 SHOR O-RING Back-Up Ring Reference Coupling Description Number (in) 8 SHBR BACK-UP RING /2 12 SHBR BACK-UP RING /4 16 SHBR BACK-UP RING SHBR BACK-UP RING /4 24 SHBR BACK-UP RING /2 32 SHBR BACK-UP RING Press-ok Super Accessories Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 33

35 SPECIAIZED MINING COUPINGS, ADAPTERS AND ACCESSORIES Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Press-ok Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Female Press-ok to Female Press-ok Reference Coupling A Description Number (in) (mm) (mm) 4FSA-4FSA /4-1/ FSA-6FSA /8-3/ FSA-8FSA /2-1/ FSA-10FSA /8-5/ FSA-12FSA /4-3/ FSA-16FSA FSA-20FSA /4-1 1/ FSA-24FSA /2-1 1/ FSA-32FSA FSA-40FSA /2-2 1/ FSA-48FSA Meets or exceeds SAE J1467. Female Press-ok to Female Press-ok - 90 Reference Coupling A B Description Number (in) (mm) (mm) (mm) 4FSA-4FSA /4-1/ FSA-6FSA /8-3/ FSA-8FSA /2-1/ FSA-12FSA /4-3/ FSA-16FSA FSA-20FSA /4-1 1/ FSA-24FSA /2-1 1/ FSA-32FSA Meets or exceeds SAE J1467. A A B Standard Hydraulic Hose Female Press-ok Swivel to Female Press-ok Swivel Reference Coupling A B Description Number (in) (mm) (mm) (mm) 4FSAX-4FSAX /4-1/ FSAX-4FSAX /8-1/ FSAX-6FSAX /8-3/ FSAX-6FSAX /2-3/ FSAX-8FSAX /2-1/ FSAX-8FSAX /4-1/ FSAX-12FSAX /4-3/ FSAX-12FSAX / FSAX-16FSAX FSAX-20FSAX /4-1 1/ Meets or exceeds SAE J1467. A B Belts Equipment 34 gates.com/mining Gates Corporation

36 Press-ok Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Female Press-ok Swivel to Female Press-ok Swivel - 45 Reference Coupling A B Description Number (in) (mm) (mm) (mm) 4FSAX-4FSAX /4-1/ FSAX-6FSAX /8-3/ FSAX-8FSAX /2-1/ FSAX-12FSAX /4-3/ FSAX-16FSAX FSAX-20FSAX /4-1 1/ Meets or exceeds SAE J1467. Female Press-ok Swivel to Female Press-ok Swivel - 90 Reference Coupling T1 A B C Description Number (in) (in) (mm) (mm) (mm) (mm) 4FSAX-4FSAX /4-1/4 1/ FSAX-6FSAX /8-3/8 3/ FSAX-6FSAX /2-3/8 1/ FSAX-8FSAX /2-1/2 1/ FSAX-12FSAX /4-3/4 3/ FSAX-16FSAX FSAX-20FSAX /4-1 1/4 1 1/ Meets or exceeds SAE J1467. Female Press-ok Fixed Tee Reference Coupling A B C Description Number X-X-Y (in) (mm) (mm) (mm) (mm) 4-4-4FSAT /4-1/4-1/ FSAT /8-3/8-3/ FSAT /2-1/2-3/ FSAT /2-1/2-1/ FSAT /4-3/4-3/ FSAT /4-3/4-1/ FSAT /4-3/4-3/ FSAT / FSAT / FSAT / FSAT FSAT /4-1 1/4-3/ FSAT /4-1 1/4-1/ FSAT /4-1 1/4-3/ FSAT /4-1 1/ FSAT /4-1 1/4-1 1/ FSAT /2-1 1/2-3/ FSAT /2-1 1/2-1/ FSAT /2-1 1/2-3/ FSAT /2-1 1/ FSAT /2-1 1/2-1 1/ FSAT /2-1 1/2-1 1/ FSAT FSAT / FSAT / FSAT FSAT /2-2 1/ FSAT /2-2 1/2-2 1/ FSAT FSAT Meets or exceeds SAE J1467. A A T1 B X A Y C B X A C B Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 35

37 SPECIAIZED MINING COUPINGS, ADAPTERS AND ACCESSORIES Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Press-ok Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Female Press-ok Swivel Tee Reference Coupling A B C Description Number X-X-Y (in) (mm) (mm) (mm) (mm) 4-4-4FSAXT /4-1/4-1/ FSAXT /8-3/8-3/ FSAXT /2-1/2-3/ FSAXT /2-1/2-1/ FSAXT /2-1/2-3/ FSAXT /4-3/4-3/ FSAXT /4-3/4-1/ FSAXT /4-3/4-3/ FSAXT /4-3/ FSAXT / FSAXT / FSAXT / FSAXT FSAXT /4-5/8-1 1/ FSAXT /4-1 1/4-3/ FSAXT /4-1 1/4-1/ FSAXT /4-1 1/4-3/ FSAXT /4-1 1/ FSAXT /4-1 1/4-1 1/ Meets or exceeds SAE J1467. Male Press-ok Adapter to Female Press-ok Adapter T Reference Coupling Description Number (in) (mm) 6MSA-6-6FSAT /8-3/8-3/ MSA-8-8FSAT /2-1/2-1/ Meets or exceeds SAE J1467. A X B Y X C Female Press-ok Y Reference Coupling A Description Number (in) (mm) (mm) 6-6-6FSAY /8-3/8-3/ Meets or exceeds SAE J1467. Standard Hydraulic Hose Female Press-ok Cross Reference Coupling A B Description Number (in) (mm) (mm) (mm) FSAC /4-1/4-1/4-1/ FSAC /8-3/8-3/8 3/ FSAC /2-1/2-1/2-1/ FSAC /4-3/4-3/4-3/ FSAC FSAC /4-1 1/4-1 1/4-1 1/ Meets or exceeds SAE J1467. A B A Belts Equipment 36 gates.com/mining Gates Corporation

38 Press-ok Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Female Press-ok K Configuration Reference Coupling A Description Number (in) (mm) (mm) FSAK /8-3/8-3/8-3/ Meets or exceeds SAE J1467. arger K sizes available. Contact Customer Service. Female Press-ok Swivel to Female British Standard Pipe Parallel - 45 A B T1 Description Number (mm) (mm) (in) Thread (mm) 4FSAX-4FBSPPX /4 1/ FSAX-6FBSPPX /8 3/ FSAX-8FBSPPX /2 1/ Meets or exceeds SAE J1467. Female Press-ok Swivel to Female British Standard Pipe Parallel - 90 A B T1 Description Number (mm) (mm) (in) Thread (mm) 4FSAX-4FBSPPX /4 1/ FSAX-6FBSPPX /8 3/ FSAX-8FBSPPX /2 1/ FSAX-12FBSPPX /4 3/ FSAX-16FBSPPX FSAX-20FBSPPX /4 1 1/ Meets or exceeds SAE J1467. Female Press-ok Swivel to NPTF Solid Male A B T1 Description Number (mm) (mm) (in) Thread (mm) 4FSAX-2MP /4 1/ FSAX-4MP /4 1/ FSAX-6MP /4 3/ FSAX-2MP /8 1/ FSAX-4MP /8 1/ FSAX-6MP /8 3/ FSAX-8MP /8 1/ FSAX-6MP /2 3/ FSAX-8MP /2 1/ FSAX-12MP /2 3/ FSAX-8MP /4 1/ FSAX-12MP /4 3/ FSAX-16MP / / FSAX-12MP / FSAX-16MP / FSAX-20MP /4-11 1/ FSAX-24MP /2-11 1/ FSAX-16MP / / FSAX-20MP /4 1 1/4-11 1/ Meets or exceeds SAE J1467. A A T1 A T1 A T1 B B B Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 37

39 SPECIAIZED MINING COUPINGS, ADAPTERS AND ACCESSORIES Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information Press-ok Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Female Press-ok to NPTF Solid Male A B T1 Description Number (mm) (mm) (in) Thread (mm) 24FSA-24MP /2 1 1/2-11 1/ FSA-32MP / Meets or exceeds SAE J1467. Female Press-ok Swivel to NPTF Solid Male - 45 A B T1 Description Number (mm) (mm) (in) Thread (mm) 4FSAX-4MP /4 1/ FSAX-6MP /8 3/ FSAX-8MP /8 1/ FSAX-6MP /2 3/ FSAX-8MP /2 1/ FSAX-12MP /2 3/ FSAX-12MP /4 3/ FSAX-16MP / FSAX-20MP /4 1 1/4-11 1/ Meets or exceeds SAE J1467. Female Press-ok Swivel to NPTF Solid Male - 90 A B T1 Description Number (mm) (mm) (in) Thread (mm) 4FSAX-4MP /4 1/ FSAX-6MP /4 3/ FSAX-6MP /8 3/ FSAX-8MP /8 1/ FSAX-8MP /2 1/ FSAX-12MP /2 3/ FSAX-16MP / FSAX-8MP /4 1/ FSAX-12MP /4 3/ FSAX-12MP / FSAX-16MP / FSAX-20MP /4 1 1/4-11 1/ Meets or exceeds SAE J1467. Female Press-ok Swivel to NPTF Solid Male - 90 ong Drop A B T1 Description Number (mm) (mm) (in) Thread (mm) 4FSAX-4MP /4 1/ FSAX-6MP /8 3/ FSAX-8MP /2 1/ FSAX-12MP /4 3/ Meets or exceeds SAE J1467. A A T1 T1 A T1 A T1 B B B B Belts 38 gates.com/mining Gates Corporation

40 Press-ok Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Female Press-ok Swivel to Male O-Ring Boss Solid A B T1 Description Number (mm) (mm) (in) Thread (mm) 4FSAX-4MB /4 7/ FSAX-5MB /4 1/ FSAX-6MB /4 9/ FSAX-4MB /8 7/ FSAX-6MB /8 9/ FSAX-8MB /8 3/ FSAX-6MB /2 9/ FSAX-8MB /2 3/ FSAX-10MB /2 7/ FSAX-12MB /2 1 1/ FSAX-10MB /4 7/ FSAX-12MB /4 1 1/ FSAX-16MB /4 1 5/ FSAX-20MB /4 1 5/ FSAX-24MB /4 1 7/ FSAX-12MB / FSAX-16MB / FSAX-16MB /4 1 5/ FSAX-20MB /4 1 5/ FSAX-24MB /2 1 7/ FSAX-32MB / Meets or exceeds SAE J1467. Female Press-ok Swivel to Male O-Ring Boss Solid - 45 A B T1 Description Number (mm) (mm) (in) Thread (mm) 4FSAX-4MB /4 7/ FSAX-6MB /4 9/ FSAX-4MB /8 7/ FSAX-6MB /8 9/ FSAX-8MB /8 3/ FSAX-6MB /2 9/ FSAX-8MB /2 3/ FSAX-10MB /2 7/ FSAX-12MB /2 1 1/ FSAX-12MB /4 1 1/ FSAX-16MB / FSAX-20MB /4 1 5/ Meets or exceeds SAE J1467. A T1 A T1 B B Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 39

41 SPECIAIZED MINING COUPINGS, ADAPTERS AND ACCESSORIES Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information Press-ok Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Female Press-ok Swivel to Male O-Ring Boss Solid - 90 A B T1 Description Number (mm) (mm) (in) Thread (mm) 4FSAX-4MB /4 7/ FSAX-6MB /4 9/ FSAX-4MB /8 7/ FSAX-6MB /8 9/ FSAX-8MB /8 3/ FSAX-6MB /2 9/ FSAX-8MB /2 3/ FSAX-10MB /2 7/ FSAX-12MB /2 1 1/ FSAX-12MB /4 1 1/ FSAX-16MB / FSAX-20MB /4 1 5/ Meets or exceeds SAE J1467. Female Press-ok Swivel to Male British Standard Pipe Parallel A B T1 Description Number (mm) (mm) (in) Thread (mm) 4FSAX-4MBSPP /4 1/ FSAX-6MBSPP /4 3/ FSAX-4MBSPP /8 1/ FSAX-6MBSPP /8 3/ FSAX-8MBSPP /8 1/ FSAX-6MBSPP /2 3/ FSAX-8MBSPP /2 1/ FSAX-10MBSPP /2 5/ FSAX-12MBSPP /2 3/ FSAX-16MBSPP / FSAX-10MBSPP /8 5/ FSAX-8MBSPP /4 1/ FSAX-12MBSPP /4 3/ FSAX-16MBSPP / FSAX-12MBSPP / FSAX-16MBSPP FSAX-20MBSPP / FSAX-16MBSPP / FSAX-20MBSPP /4 1 1/ FSAX-24MBSPP /4 1 1/ Meets or exceeds SAE J1467. Female Press-ok Swivel to Male British Standard Pipe Parallel - 45 A B T1 Description Number (mm) (mm) (in) Thread (mm) 6FSAX-6MBSPP /8 3/ FSAX-8MBSPP /2 1/ FSAX-16MBSPP Meets or exceeds SAE J1467. A T1 A T1 A T1 B B B Belts 40 gates.com/mining Gates Corporation

42 Press-ok Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Female Press-ok Swivel to Male British Standard Pipe Parallel - 90 A B T1 Description Number (mm) (mm) (in) Thread (mm) 12FSAX-12MBSPP /4 3/ Meets or exceeds SAE J1467. Female Press-ok Swivel to Male BSP O-Ring A B T1 Description Number (mm) (mm) (in) Thread (mm) 4FSAX-4MBSPPOR /4 1/ FSAX-6MBSPPOR /8 7/ FSAX-8MBSPPOR /8 1/ FSAX-6MBSPPOR /2 7/ FSAX-8MBSPPOR /2 1/ FSAX-12MBSPPOR /2 3/ FSAX-16MBSPPOR /2 9/ FSAX-8MBSPPOR /4 1/ FSAX-12MBSPPOR /4 3/ FSAX-16MBSPPOR / FSAX-12MBSPPOR / FSAX-16MBSPPOR FSAX-20MBSPPOR / FSAX-16MBSPPOR / FSAX-20MBSPPOR /4 1 1/ Meets or exceeds SAE J1467. Female Press-ok Swivel to Female Banjo Fitting A B C T1 Bolt Description Number (mm) (mm) (mm) (in) (mm) Size 4FSAX-4BJ / /4 BSP 6FSAX-6BJ / /8 BSP 8FSAX-6BJ / /8 BSP 8FSAX-8BJ / /2 BSP 12FSAX-12BJ / /4 BSP 16FSAX-16BJ BSP 20FSAX-20BJ / /4 BSP Meets or exceeds SAE J1467. Press-ok Banjo Washer Reference Coupling Description Number (in) 4BW /4 6BW /8 8BW /2 Meets or exceeds SAE J1467. A T1 A T1 A T1 BOT SIZE B B C B Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 41

43 SPECIAIZED MINING COUPINGS, ADAPTERS AND ACCESSORIES Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information Press-ok Banjo Bolt BSP Thread Press-ok Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Description Number Thread (mm) 4BB / BB / BB / BB / BB BB / Meets or exceeds SAE J1467. Male Press-ok to Female Press-ok A T1 Description Number (mm) (in) (mm) 16MSA-12FSA Meets or exceeds SAE J1467. Male Press-ok to Female Press-ok - 45 A T1 Description Number (mm) (in) (mm) 6MSA-6FSA / MSA-8FSA / MSA-12FSA / Meets or exceeds SAE J1467. Male Press-ok to Female Press-ok - 90 A T1 T2 Description Number (mm) (in) (in) (mm) 6MSA-6FSA /8 3/ MSA-8FSA /2 1/ MSA-12FSA /4 3/ Meets or exceeds SAE J1467. Male Press-ok to Female Press-ok to Female Press-ok A T1 Description Number (mm) (in) (mm) 16MSA-16FSA-6FSA Meets or exceeds SAE J1467. T1 T1 T1 A T1 T2 A T1 A T1 A Equipment T1 Belts T1 A 42 gates.com/mining Gates Corporation

44 Press-ok Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Male Press-ok to Female Press-ok Swivel A T1 T2 Description Number (mm) (in) (in) (mm) 4MSA-4FSAX /4 1/ MSA-6FSAX /4 3/ MSA-8FSAX /4 1/ MSA-4FSAX /8 1/ MSA-6FSAX /8 3/ MSA-8FSAX /8 1/ MSA-12FSAX /8 3/ MSA-20FSAX /8 1 1/ MSA-4FSAX /2 1/ MSA-6FSAX /2 3/ MSA-8FSAX /2 1/ MSA-12FSAX /2 3/ MSA-16FSAX / MSA-20FSAX /2 1 1/ MSA-6FSAX /4 3/ MSA-8FSAX /4 1/ MSA-12FSAX /4 3/ MSA-16FSAX / MSA-20FSAX /4 1 1/ MSA-12FSAX / MSA-16FSAX MSA-20FSAX / MSA-24FSAX / MSA-32FSAX MSA-12FSAX /4 3/ MSA-16FSAX / MSA-20FSAX /4 1 1/ MSA-24FSAX /4 1 1/ MSA-32FSAX / MSA-16FSAX / MSA-20FSAX /2 1 1/ MSA-24FSAX /2 1 1/ MSA-32FSAX / MSA-16FSAX MSA-20FSAX / MSA-24FSAX / MSA-32FSAX Meets or exceeds SAE J1467. Male Press-ok to Female Press-ok Swivel - 45 A T1 T2 Description Number (mm) (in) (in) (mm) 4MSA-4FSAX /4 1/ MSA-4FSAX /8 1/ MSA-6FSAX /8 3/ MSA-6FSAX /2 3/ MSA-8FSAX /2 1/ MSA-12FSAX /2 3/ MSA-12FSAX /4 3/ MSA-16FSAX MSA-20FSAX /4 1 1/ Meets or exceeds SAE J1467. T1 T1 T2 A A T2 Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 43

45 SPECIAIZED MINING COUPINGS, ADAPTERS AND ACCESSORIES Belts Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information Press-ok Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Male Press-ok to Female Press-ok Swivel - 90 A B T1 T2 Description Number (mm) (mm) (in) (in) (mm) 4MSA-4FSAX /4 1/ MSA-6FSAX /4 3/ MSA-8FSAX /4 1/ MSA-4FSAX /8 1/ MSA-6FSAX /8 3/ MSA-8FSAX /8 1/ MSA-4FSAX /2 1/ MSA-6FSAX /2 3/ MSA-8FSAX /2 1/ MSA-12FSAX /2 3/ MSA-10FSAX /8 5/ MSA-8FSAX /4 1/ MSA-12FSAX /4 3/ MSA-16FSAX / MSA-20FSAX /4 1 1/ MSA-12FSAX / MSA-16FSAX MSA-20FSAX / MSA-12FSAX /4 3/ MSA-16FSAX / MSA-20FSAX /4 1 1/ MSA-24FSA /2 1 1/ MSA-32FSA Meets or exceeds SAE J1467. Male Press-ok to Male Press-ok A B T1 T2 Description Number (mm) (mm) (in) (in) (mm) 4MSA-4MSA /4 1/ MSA-4MSA /8 1/ MSA-6MSA /8 3/ MSA-6MSA /8 3/ MSA-4MSA /2 1/ MSA-6MSA /2 3/ MSA-8MSA /2 1/ MSA-4MSA /8 1/ MSA-10MSA /8 5/ MSA-6MSA /4 3/ MSA-8MSA /4 1/ MSA-12MSA /4 3/ MSA-8MSA / MSA-10MSA / MSA-12MSA / MSA-16MSA MSA-12MSA /4 3/ MSA-16MSA / MSA-20MSA /4 1 1/ MSA-8MSA /2 1/ MSA-12MSA /2 3/ MSA-16MSA / MSA-20MSA /2 1 1/ MSA-24MSA /2 1 1/ MSA-16MSA MSA-24MSA / MSA-32MSA MSA-40MSA /2 2 1/ MSA-48MSA Meets or exceeds SAE J1467. T1 T1 A T2 A B B T2 44 gates.com/mining Gates Corporation

46 Press-ok Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Male Press-ok to NPTF Solid Male A T1 Description Number (mm) (in) Thread (mm) 4MSA-2MP /4 1/ MSA-4MP /4 1/ MSA-6MP /4 3/ MSA-12MP /4 3/ MSA-2MP /8 1/ MSA-4MP /8 1/ MSA-6MP /8 3/ MSA-8MP /8 1/ MSA-12MP /8 3/ MSA-4MP /2 1/ MSA-6MP /2 3/ MSA-8MP /2 1/ MSA-12MP /2 3/ MSA-16MP / / MSA-6MP /4 3/ MSA-8MP /4 1/ MSA-12MP /4 3/ MSA-16MP / / MSA-12MP / MSA-16MP / MSA-20MP /4-11 1/ MSA-20MP /4 1 1/4-11 1/ MSA-24MP /4 1 1/2-11 1/ MSA-20MP /2 1 1/4-11 1/ MSA-24MP /2 1 1/2-11 1/ MSA-32MP / Meets or exceeds SAE J1467. Male Press-ok to Male O-Ring Boss Solid A T1 Description Number (mm) (in) Thread (mm) 4MSA-4MB /4 7/ MSA-5MB /4 1/ MSA-6MB /4 9/ MSA-4MB /8 7/ MSA-6MB /8 9/ MSA-8MB /8 3/ MSA-10MB /8 7/ MSA-12MB /8 1 1/ MSA-6MB /2 9/ MSA-8MB /2 3/ MSA-10MB /2 7/ MSA-12MB /2 1 1/ MSA-16MB /2 1 5/ MSA-8MB /4 3/ MSA-10MB /4 7/ MSA-12MB /4 1 1/ MSA-16MB /4 1 5/ MSA-12MB / MSA-16MB / MSA-20MB / MSA-20MB /4 1 5/ Meets or exceeds SAE J1467. T1 T1 A A Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 45

47 SPECIAIZED MINING COUPINGS, ADAPTERS AND ACCESSORIES Belts Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information Press-ok Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Male Press-ok to Male British Standard Pipe Parallel A T1 Description Number (mm) (in) Thread (mm) 4MSA-4MBSPP /4 1/ MSA-6MBSPP /4 3/ MSA-4MBSPP /8 1/ MSA-6MBSPP /8 3/ MSA-8MBSPP /8 1/ MSA-6MBSPP /2 3/ MSA-8MBSPP /2 1/ MSA-12MBSPP /2 3/ MSA-16MBSPP / MSA-10MBSPP /4 5/ MSA-12MBSPP /4 3/ MSA-16MBSP P / MSA-12MBSPP / MSA-16MBSPP MSA-20MBSPP / MSA-20MBSPP /4 1 1/ MSA-24MBSPP /4 1 1/ MSA-24MBSPP /2 1 1/ MSA-32MBSPP Meets or exceeds SAE J1467. Female Press-ok Cap A T1 Description Number (mm) (in) (mm) 4FSA / FSA / FSA / FSA / FSA FSA / FSA / FSA FSA / FSA Meets or exceeds SAE J1467. Male Press-ok Plug A T1 Description Number (mm) (in) (mm) 4MSA / MSA / MSA / MSA / MSA / MSA MSA / MSA / MSA MSA / MSA Meets or exceeds SAE J1467. T1 A T1 T1 A A 46 gates.com/mining Gates Corporation

48 Press-ok Adapters Gates can make special designs, angles, bores, etc. Contact Gates Customer Service with your detailed needs. Male Press-ok to Female Ball Valve Adapter Reference Coupling A Description Number (in) (mm) (mm) 4MS-4FSXBV /4-1/ MS-6FSXBV /8-3/ MS-8FSXBV /2-1/ MS-12FSXBV /4-3/ MS-16FSXBV MS-20FSXBV /4-1 1/ MS-24FSXBV /2-1 1/ MS-32FSXBV Meets or exceeds SAE J1467. T handle to 1", single arm crank 1 ¼" and above as shown in illustration. Female Press-ok Ball Valve to Female Ball Valve Adapter Reference Coupling A Description Number (in) (mm) (mm) 4FSX-4FSXBV /4-1/ FSX-6FSXBV /8-3/ FSX-8FSXBV /2-1/ FSX-12FSXBV /4-3/ FSX-16FSXBV FSX-20FSXBV /4-1 1/ FSX-24FSXBV /2-1 1/ FSX-32FSXBV Meets or exceeds SAE J1467. T handle to 1", single arm crank 1 ¼" and above as shown in illustration. A A Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 47

49 SPECIAIZED MINING COUPINGS, ADAPTERS AND ACCESSORIES Belts Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information Staple - Carbon Steel Reference Coupling Description Number (in) 4SS STAPE /4 6SS STAPE /8 8SS STAPE /2 10SS STAPE /8 12SS STAPE /4 16SS STAPE SS STAPE /4 24SS STAPE /2 32SS STAPE SS STAPE /2 48SS STAPE For static pressure applications. Staple - Stainless Steel Reference Coupling Description Number (in) 4SSS STAPE /4 6SSS STAPE /8 8SSS STAPE /2 10SSS STAPE /8 12SSS STAPE /4 16SSS STAPE SSS STAPE /4 24SSS STAPE /2 32SSS STAPE For impulse pressure applications. O-Ring Reference Coupling Description Number (in) 4SOR O-RING /4 6SOR O-RING /8 8SOR O-RING /2 10SOR O-RING /8 12SOR O-RING /4 16SOR O-RING SOR O-RING /4 24SOR O-RING /2 32SOR O-RING Back-Up Ring Reference Coupling Description Number (in) 4SBR BACK-UP RG /4 6SBR BACK-UP RG /8 8SBR BACK-UP RG /2 10SBR BACK-UP RG /8 12SBR BACK-UP RG /4 16SBR BACK-UP RG SBR BACK-UP RG /4 24SBR BACK-UP RG /2 32SBR BACK-UP RG Press-ok Accessories 48 gates.com/mining Gates Corporation

50 Press-ok ow Profile Adapters and Accessories Press-ok ow Profile Male to NPTF Solid Male B C Description Number (mm) (mm) (mm) 24PM-24MP Press-ok ow Profile Male to Male Press-ok T2 B C Description Number (in) (mm) (mm) (mm) 24PM-24MSA / Press-ok ow Profile Male to Female Press-ok Reference Coupling Description Number (in) 24PM-24FSA /2 Staple for ow Pressure Carbon Steel Reference Coupling Description Number (in) 24SS /2 32SS C C C B B B T2 Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 49

51 STANDARD HYDRAUIC HOSE Information G8K Spiral Wire Hose Ultra High Pressure Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Meets Flame Resistance Acceptance Designation "MSHA 2G" Ultra high-pressure, high-impulse applications such as hydrostatic transmissions, for use in the construction, agriculture, forestry, underground or open pit mining, or other industries on applications where extremely high pressure capability is required. G8K hose and couplings offer industry-leading bend radius capability, which leads to ease of routing and installation, longer hose life in flexing applications, and fewer bent tube fitting requirements. Black, oil-resistant Neoprene Type A tube material allows for the high pressure, high temperature performance required in these demanding applications. See Hose Stock Characteristics. Six alternating layers of high tensile steel wire spiral construction. Black, oil resistant, synthetic rubber (Neoprene - Type A), with color coded layline. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): G8K Couplings EFG6K Spiral Wire Hose SAE 100R15 For Biodegradable Hydraulic Fluids Extremely High Pressure Standard Hydraulic Hose Equipment Belts Meets Flame Resistance Acceptance Designation "MSHA 2G" Extremely high-pressure, high-impulse applications such as hydrostatic transmissions. EFG6K is designed to meet or exceed all requirements of SAE 100R15 specifications and performance requirements of EN 856 4SP (-6, -8, -10 and -12), EN 856 4SH (-12, -16, and -20), and ISO 3862 Type R15 (-6, -8, -10, -12, -16, -24 and -32). Compatible with biodegradable hydraulic fluids like polyolester, polyglycol and vegetable oil as well as standard petroleum-based fluids. Available in 121' through 200' continuous lengths. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Four (six for -20, -24 and -32) alternating layers of spiraled, high-tensile steel. Black, oil resistant, synthetic rubber (Neoprene - Type A). Color coded layline. Also available with unique abrasion resistant MegaTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings (-6 through -20) GlobalSpiral High Pressure Couplings (-24 and -32) Stainless Steel "S" Couplings 50 gates.com/mining Gates Corporation

52 Extremely High Pressure Extremely High Pressure For Biodegradable Hydraulic Fluids EFG6K Spiral Wire Hose MegaTuff Cover For Biodegradable Hydraulic Fluids MegaTuff hose lasts up to 300 times longer than standard hose during hose-to-hose and hose-to-metal abrasion tests per ISO Meets Flame Resistance Acceptance Designation "MSHA 2G" Extremely high-pressure, high-impulse applications such as hydrostatic transmissions. EFG6K is designed to meet or exceed all requirements of SAE 100R15 specifications and performance requirements of EN 856 4SP (-6, -8, -10 and -12), EN 856 4SH (-12, -16, and -20), and ISO 3862 Type R15 (-6, -8, -10, -12, -16, -24 and -32). Compatible with biodegradable hydraulic fluids like polyolester, polyglycol and vegetable oil as well as standard petroleum-based fluids. Available in 121' through 200' continuous lengths. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Four (six for 20, -24 and -32) alternating layers of spiraled, high-tensile steel. Black, oil, abrasion and weather resistant MegaTuff cover with synthetic rubber (Neoprene - Type A) base, with color coded layline. Also available in Standard cover. See Hose Stock Characteristics. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings (-6 through -20) GlobalSpiral High Pressure Couplings (-24 and -32) Stainless Steel "S" Couplings EFG5K Spiral Wire Hose SAE 100R13 Meets Flame Resistance Acceptance Designation "MSHA 2G" Extremely high-pressure, high-impulse applications such as hydrostatic transmissions. EFG5K is designed to meet or exceed all requirements of SAE 100R13 specifications and performance requirements of EN 856 4SP (-6, -8, -10 and -12), EN 856 4SH (-12, -16, and -20), and ISO 3862 Type R13 (-6, -8, -10, -12, -16, -24). Compatible with biodegradable hydraulic fluids like polyolester, polyglycol and vegetable oil as well as standard petroleum-based fluids. Available in 121' through 200' continuous lengths. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Four (six for 20, -24 and -32) alternating layers of spiraled, high-tensile steel. Black, oil resistant, synthetic rubber (Neoprene - Type A), with color coded layline. Also available with unique abrasion resistant MegaTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings (-6 through -20) GlobalSpiral High Pressure Couplings (-24 and -32) Stainless Steel "S" Couplings Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 51

53 STANDARD HYDRAUIC HOSE Information EFG5K Spiral Wire Hose MegaTuff Cover For Biodegradable Hydraulic Fluids Extremely High Pressure MegaTuff hose lasts up to 300 times longer than standard hose during hose-to-hose and hose-to-metal abrasion tests per ISO Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Meets Flame Resistance Acceptance Designation "MSHA 2G" Extremely high-pressure, high-impulse applications such as hydrostatic transmissions. EFG5K is designed to meet or exceed all requirements of SAE 100R13 specifications and performance requirements of EN 856 4SP (-6, -8, -10 and -12), EN 856 4SH (-12, -16, and -20), and ISO 3862 Type R13 (-6, -8, -10, -12, -16, -24). Compatible with biodegradable hydraulic fluids like polyolester, polyglycol and vegetable oil as well as standard petroleum-based fluids. Available in 121' through 200' continuous lengths. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Four (six for -20 and -24) alternating layers of spiraled, high-tensile steel. Black, oil, abrasion and weather resistant MegaTuff cover with synthetic rubber (Neoprene - Type A) base, with color coded layline. Also available in Standard cover. See Hose Stock Characteristics. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings (-6 through -20) GlobalSpiral High Pressure Couplings (-24 and -32) Stainless Steel "S" Couplings EFG4K Spiral Wire Hose SAE 100R12 For Biodegradable Hydraulic Fluids Extremely High Pressure Standard Hydraulic Hose Equipment Belts Meets Flame Resistance Acceptance Designation "MSHA 2G" Extremely high-pressure, high-impulse applications. Exceeds all performance requirements for SAE 100R12, EN 856 R12 and ISO 3862 Type R12. Compatible with biodegradable hydraulic fluids like polyolester, polyglycol and vegetable oil as well as standard petroleum-based fluids. Available in 121' through 200' continuous lengths. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Four alternating layers of spiraled, high-tensile steel wire. Black, oil resistant, synthetic rubber (Neoprene - Type A), with color coded layline. Also available with unique abrasion resistant MegaTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings Stainless Steel "S" Couplings 52 gates.com/mining Gates Corporation

54 Extremely High Pressure Extremely High Pressure EFG4K Spiral Wire Hose MegaTuff Cover For Biodegradable Hydraulic Fluids MegaTuff hose lasts up to 300 times longer than standard hose during hose-to-hose and hose-to-metal abrasion tests per ISO Meets Flame Resistance Acceptance Designation "MSHA 2G" Extremely high-pressure, high-impulse applications. Exceeds all performance requirements for SAE 100R12, EN 856 R12 and ISO 3862 Type R12. Compatible with biodegradable hydraulic fluids like polyolester, polyglycol and vegetable oil as well as standard petroleum-based fluids. Available in 121' through 200' continuous lengths. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Four alternating layers of spiraled, high-tensile steel wire. Black, oil, abrasion and weather resistant MegaTuff cover with synthetic rubber (Neoprene - Type A) base, with color coded layline. Also available in Standard cover. See Hose Stock Characteristics. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings Stainless Steel "S" Couplings For Biodegradable Hydraulic Fluids EFG3K Spiral Wire Hose SAE 100R12 Meets Flame Resistance Acceptance Designation "MSHA 2G" Extremely high-pressure, high-impulse applications. Exceeds all performance requirements for SAE 100R12, EN 856 R12, performance requirements of EN 856 4SP, and ISO 3862 Type R12. Compatible with biodegradable hydraulic fluids like polyolester, polyglycol and vegetable oil as well as standard petroleum-based fluids. Available in 121' through 200' continuous lengths. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Four alternating layers of spiraled, high-tensile steel wire. Black, oil resistant, synthetic rubber (Neoprene - Type A), with color coded layline. Also available with unique abrasion resistant MegaTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GSP Couplings (-24 and -32) GlobalSpiral Couplings (-6 through -20) Stainless Steel "S" Couplings Powering Progress. gates.com/mining 53 Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts

55 STANDARD HYDRAUIC HOSE Information EFG3K Spiral Wire Hose MegaTuff Cover For Biodegradable Hydraulic Fluids Extremely High Pressure MegaTuff hose lasts up to 300 times longer than standard hose during hose-to-hose and hose-to-metal abrasion tests per ISO Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Meets Flame Resistance Acceptance Designation "MSHA 2G" Extremely high-pressure, high-impulse applications. Exceeds all performance requirements for SAE 100R12, EN 856 R12, performance requirements of EN 856 4SP, and ISO 3862 Type R12. Compatible with biodegradable hydraulic fluids like polyolester, polyglycol and vegetable oil as well as standard petroleum-based fluids. Available in 121' through 200' continuous lengths. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Four alternating layers of spiraled, high-tensile steel wire. Black, oil, abrasion and weather resistant MegaTuff cover with synthetic rubber (Neoprene - Type A) base, with color coded layline. Also available in Standard cover. See Hose Stock Characteristics. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GSP Couplings (-24 and -32) GlobalSpiral Couplings (-6 through -20) Stainless Steel "S" and "B" Couplings Hot Oiler 2-Wire Braid Hose High Pressure Standard Hydraulic Hose Equipment Meets Flame Resistance Acceptance Designation "MSHA 2G" Static pressure, hot oiler applications. Designed specifically to handle the transfer of hot oil at 275 F continuous, 300 F intermittent to clear the paraffin around the casing to help start the flow of oil to the surface. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil and abrasion resistant, synthetic rubber (Hypalon - Type M). Temperature Range: -40 F to +300 F (-40 C to +149 C). For water emulsions see Temperature imits Table or E-crimp): Field Attachable Type T Couplings GSP Couplings Belts Hypalon is a Registered Trademark of E.I. du Pont de Nemours and Company. 54 gates.com/mining Gates Corporation

56 High Pressure High Pressure M-XP Million Impulse Xtra Performance Wire Braid Hose Meets Flame Resistance Acceptance Designation "MSHA 2G" High-pressure, high impulse life hydraulic applications. Provides tighter than standard minimum bend radius and greater flexibility for easier plumbing. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil, abrasion and weather resistant, synthetic rubber (Modified Nitrile - Type C2), with color coded layline. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): MegaCrimp Couplings Global M6K Mega6000 Hose Meets Flame Resistance Acceptance Designation "MSHA 2G" High-pressure hydraulic applications. Provides tighter than standard minimum bend radius and greater flexibility for easier plumbing. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil, abrasion and weather resistant, synthetic rubber (Modified Nitrile - Type C2), with color coded layline. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): MegaCrimp Couplings Stainless Steel "B" Couplings Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 55

57 STANDARD HYDRAUIC HOSE Information Global M5K Mega5000 Hose High Pressure Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Meets Flame Resistance Acceptance Designation "MSHA 2G" High-pressure hydraulic applications. Provides tighter than standard minimum bend radius and greater flexibility for easier plumbing. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil, abrasion and weather resistant, synthetic rubber (Modified Nitrile - Type C2), with color coded layline. Also available with unique abrasion resistant MegaTuff or XtraTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Stainless Steel "B" Couplings Global M5K Mega5000 Hose MegaTuff Cover M5K-MTF High Pressure Standard Hydraulic Hose Meets Flame Resistance Acceptance Designation "MSHA 2G" High-pressure hydraulic applications. Provides tighter than standard minimum bend radius and greater flexibility for easier plumbing. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil, abrasion and weather resistant MegaTuff cover with synthetic rubber (Neoprene - Type A) base, with color coded layline. Also available in Standard or XtraTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Belts Equipment 56 gates.com/mining Gates Corporation

58 High Pressure High Pressure Global M5K Mega5000 Hose XtraTuff Cover Meets Flame Resistance Acceptance Designation "MSHA 2G" High-pressure hydraulic applications. Provides tighter than standard minimum bend radius and greater flexibility for easier plumbing. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil, abrasion and weather resistant, synthetic rubber (Modified Nitrile - Type C2), with color coded layline. Also available in Standard or MegaTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Global M4K Mega4000 Hose SAE 100R19 Meets Flame Resistance Acceptance Designation "MSHA 2G", and ISO11237 R19 High-pressure hydraulic applications. Exceeds SAE 100R19 and ISO11237 R19. Allows for tighter minimum bend radius, increased working pressure and improved impulse cycles than industry standards. Provides greater performance, flexibility, easier routing and plumbing of mobile and stationary hydraulic platforms. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil, abrasion and weather resistant, synthetic rubber (Modified Nitrile - Type C2), with color coded layline. Also available with unique abrasion resistant MegaTuff or XtraTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Stainless Steel "S" and "B" Couplings Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 57

59 STANDARD HYDRAUIC HOSE Information Global M4K Mega4000 Hose MegaTuff Cover High Pressure MegaTuff hose lasts up to 300 times longer than standard hose during hose-to-hose and hose-to-metal abrasion tests per ISO Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Meets Flame Resistance Acceptance Designation "MSHA 2G", and ISO11237 R19 High-pressure hydraulic applications. Exceeds SAE 100R19 and ISO11237 R19. Allows for tighter minimum bend radius, increased working pressure and improved impulse cycles than industry standards. Provides greater performance, flexibility, easier routing and plumbing of mobile and stationary hydraulic platforms. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil, abrasion and weather resistant MegaTuff cover with synthetic rubber (Neoprene - Type A) base, with color coded layline. Also available in Standard or XtraTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Stainless Steel "S" and "B" Couplings Global M4K Mega4000 Hose XtraTuff Cover High Pressure XtraTuff hose lasts up to 25 times longer than standard hose during hose-to-hose and hose-to-metal abrasion tests per ISO Standard Hydraulic Hose Meets Flame Resistance Acceptance Designation "MSHA 2G", and ISO11237 R19 High-pressure hydraulic applications. Exceeds SAE 100R19 and ISO11237 R19. Allows for tighter minimum bend radius, increased working pressure and improved impulse cycles than industry standards. Provides greater performance, flexibility, easier routing and plumbing of mobile and stationary hydraulic platforms. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil, abrasion and weather resistant, synthetic rubber (Modified Nitrile - Type C2), with color coded layline. Also available in Standard or MegaTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Stainless Steel "S" and "B" Couplings Belts Equipment 58 gates.com/mining Gates Corporation

60 High Pressure High Pressure M4KH Wire Braid Hose High-Temp SAE 100R19 (Meets Flame Resistance Acceptance Designation "MSHA 2G", and ISO11237 R19) Meets Flame Resistance Acceptance Designation "MSHA 2G", and ISO11237 R19 High-pressure hydraulic applications. Exceeds SAE 100R19 and ISO11237 R19. Allows for tighter minimum bend radius, increased working pressure and improved impulse cycles than industry standards. Provides greater performance, flexibility, easier routing and plumbing of mobile and stationary hydraulic platforms. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil, abrasion and weather resistant, thin synthetic rubber (Neoprene - CR), with color coded layline. Flame resistance - MSHA 2G. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Stainless Steel "S" and "B" Couplings M4KH Wire Braid Hose High-Temp MegaTuff Cover MegaTuff hose lasts up to 300 times longer than standard hose during hose-to-hose and hose-to-metal abrasion tests per ISO Meets Flame Resistance Acceptance Designation "MSHA 2G", and ISO11237 R19 High-pressure hydraulic applications. Exceeds SAE 100R19 and ISO11237 R19. Allows for tighter minimum bend radius, increased working pressure and improved impulse cycles than industry standards. Provides greater performance, flexibility, easier routing and plumbing of mobile and stationary hydraulic platforms. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil, abrasion and weather resistant MegaTuff cover with synthetic rubber (Neoprene - Type A) base, with color coded layline. Flame resistance - MSHA 2G. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Stainless Steel "S" and "B" Couplings Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 59

61 STANDARD HYDRAUIC HOSE Information Global M3K Mega3000 Hose SAE 100R17 High Pressure Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Meets Flame Resistance Acceptance Designation "MSHA 2G", and ISO11237 R17 High-pressure hydraulic oil lines. Exceeds SAE 100R17 and ISO11237 R17 working pressure, minimum bend radius requirements and performance requirements of EN 857 1SC. M3K hose has smaller exterior dimensions and significantly tighter bend radius than other SAE 100R1 and 100R2 hose. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Braided, high-tensile steel wire. -4, -5, -6 and -8 sizes are one braid; -10, -12 and -16 sizes are two braid. Black, oil, abrasion and weather resistant, synthetic rubber (Modified Nitrile - Type C2), with color coded layline. Also available with unique abrasion resistant MegaTuff or XtraTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Power Crimp Couplings (-3 only) Stainless Steel "B" Couplings Global M3K Mega3000 Hose MegaTuff Cover High Pressure MegaTuff hose lasts up to 300 times longer than standard hose during hose-to-hose and hose-to-metal abrasion tests per ISO Standard Hydraulic Hose Equipment Belts Meets Flame Resistance Acceptance Designation "MSHA 2G", and ISO11237 R17 High-pressure hydraulic oil lines. Exceeds SAE 100R17 and ISO11237 R17 working pressure, minimum bend radius requirements and performance requirements of EN 857 1SC. M3K hose has smaller exterior dimensions and significantly tighter bend radius than other SAE 100R1 and 100R2 hose. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Braided, high-tensile steel wire. -4, -5, -6 and -8 sizes are one braid; -10, -12 and -16 sizes are two braid. Black, oil, abrasion and weather resistant MegaTuff cover with synthetic rubber (Neoprene - Type A) base, with color coded layline. Also available in Standard or XtraTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Power Crimp Couplings (-3 only) Stainless Steel "B" Couplings 60 gates.com/mining Gates Corporation

62 High Pressure High Pressure Global M3K Mega3000 Hose XtraTuff Cover XtraTuff hose lasts up to 25 times longer than standard hose during hose-to-hose and hose-to-metal abrasion tests per ISO Meets Flame Resistance Acceptance Designation "MSHA 2G", and ISO11237 R17 High-pressure hydraulic oil lines. Exceeds SAE 100R17 and ISO11237 R17 working pressure, minimum bend radius requirements and performance requirements of EN 857 1SC. M3K hose has smaller exterior dimensions and significantly tighter bend radius than other SAE 100R1 and 100R2 hose. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Braided, high-tensile steel wire. -4, -5, -6 and -8 sizes are one braid; -10, -12 and -16 sizes are two braid. Black, oil, abrasion and weather resistant, synthetic rubber (Modified Nitrile - Type C2), with color coded layline. Also available in Standard or MegaTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Power Crimp Couplings (-3 only) Stainless Steel "B" Couplings M3KH Wire Braid Hose High-Temp SAE 100R17 Meets Flame Resistance Acceptance Designation "MSHA 2G", and ISO11237 R17 High-pressure hydraulic oil lines. Exceeds SAE 100R17 and ISO11237 R17 requirements and performance requirements of EN 857 1SC. M3KH hose has smaller exterior dimensions and significantly tighter bend radius than other SAE 100R1 and 100R2 hose. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. One braid of high-tensile steel wire. Black, oil, abrasion and weather resistant, synthetic rubber (Neoprene CR), with color coded layline. See Hose Stock Characteristics. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Stainless Steel "B" Couplings Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 61

63 STANDARD HYDRAUIC HOSE Information M3KH Wire Braid Hose High-Temp MegaTuff Cover High Pressure MegaTuff hose lasts up to 300 times longer than standard hose during hose-to-hose and hose-to-metal abrasion tests per ISO Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Meets Flame Resistance Acceptance Designation "MSHA 2G", and ISO11237 R17 High-pressure hydraulic oil lines. Exceeds SAE 100R17 and ISO11237 R17 working pressure, minimum bend radius requirements and performance requirements of EN 857 1SC. M3KH hose has smaller exterior dimensions and significantly tighter bend radius than other SAE 100R1 and 100R2 hose. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. One braid of high-tensile steel wire. Black, oil, abrasion and weather resistant MegaTuff cover with synthetic rubber (Neoprene - Type A) base, with color coded layline. Also available in Standard cover. See Hose Stock Characteristics. Temperature Range: -40 F to +250 F (-40 C to +121 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Stainless Steel "B" Couplings M2T MegaFlex 2-Wire Braid Hose SAE 100R16 High Pressure Standard Hydraulic Hose Meets Flame Resistance Acceptance Designation "MSHA 2G", and ISO SC R16 High-pressure hydraulic oil lines. Exceeds SAE 100R16 and ISO SC R16 requirements and performance requirements of EN 857 2SC. M2T hose has smaller exterior dimensions and significantly tighter bend radius. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil, abrasion and weather resistant, synthetic rubber (Modified Nitrile - Type C2), with color coded layline. Also available with unique abrasion resistant MegaTuff or XtraTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Stainless Steel "B" Couplings Belts Equipment 62 gates.com/mining Gates Corporation

64 High Pressure High Pressure M2T MegaFlex 2-Wire Braid Hose MegaTuff Cover MegaTuff hose lasts up to 300 times longer than standard hose during hose-to-hose and hose-to-metal abrasion tests per ISO Meets Flame Resistance Acceptance Designation "MSHA 2G", and ISO SC R16 High-pressure hydraulic oil lines. Exceeds SAE 100R16 and ISO SC R16 working pressure, minimum bend radius requirements and performance requirements of EN 857 2SC. M2T hose has smaller exterior dimensions and significantly tighter bend radius. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil, abrasion and weather resistant MegaTuff cover with synthetic rubber (Neoprene - Type A) base, with color coded layline. Also available in Standard or XtraTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Stainless Steel "B" Couplings M2T MegaFlex 2-Wire Braid Hose XtraTuff XtraTuff hose lasts up to 25 times longer than standard hose during hose-to-hose and hose-to-metal abrasion tests per ISO Meets Flame Resistance Acceptance Designation "MSHA 2G", and ISO SC R16 High-pressure hydraulic oil lines. Exceeds SAE 100R16 and ISO SC R16 working pressure, minimum bend radius requirements and performance requirements of EN 857 2SC. M2T hose has smaller exterior dimensions and significantly tighter bend radius. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil, abrasion and weather resistant, synthetic rubber (Modified Nitrile - Type C2), with color coded layline. Also available in Standard or MegaTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Stainless Steel "B" Couplings Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 63

65 STANDARD HYDRAUIC HOSE Information CM2T MegaFlex Connected Twin-ine 2-Wire Braid SAE 100R16 High Pressure Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Meets Flame Resistance Acceptance Designation "MSHA 2G" High-pressure hydraulic oil lines joined together for easier plumbing and routing. Meets SAE 100R16 requirements. CM2T hose has smaller exterior dimensions and significantly tighter bend radius. Exceeds performance standards of EN 857 2SC and ISO/DIS Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil, abrasion and weather resistant, synthetic rubber (Modified Nitrile - Type C2), with color coded layline. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): MegaCrimp Couplings Global G2 2-Wire Braid Hose SAE 100R2 Type AT High Pressure Standard Hydraulic Hose Meets Flame Resistance Acceptance Designation "MSHA 2G" High-pressure hydraulic oil lines. Meets or exceeds the requirements of SAE 100R2, ISO1436 2SN R2 and EN 853 2SN. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil and abrasion resistant, thin synthetic rubber (Modified Nitrile - Type C2). See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): Field Attachable Type T Couplings GSP Couplings (-24 and -32) GlobalSpiral Couplings MegaCrimp Couplings (except -24 and -32) Stainless Steel "B" Couplings Belts Equipment 64 gates.com/mining Gates Corporation

66 High Pressure High Pressure G2XH 2-Wire Braid Extreme Heat Hose SAE 100R2 Meets Flame Resistance Acceptance Designation "MSHA 2G" High-pressure hydraulic applications where pressure or temperature requirements exceed SAE 100R2, ISO1436 2SN R2 and EN 853 2SN or where resistance to either petroleum-base or phosphate ester fluids is required. Meets SAE J1942 requirements. Black, oil and chemical resistant, synthetic rubber (CPE). Two braids of high-tensile steel wire. Blue, oil and abrasion resistant, thin synthetic rubber Hypalon. Flame resistance - U.S. MSHA 2G. Temperature Range: Petroleum-base fluids: -40 F to +300 F (-40 C to +149 C). Phosphate esters fluids as recommended by the fluid manufacturer, but within a range of -40 F to +212 F. For water emulsions: Max F Pressure lines, Max +180 F Return lines. For water emulsions see Temperature imits Table or E-crimp): GlobalSpiral Couplings MegaCrimp Couplings Hypalon is a Registered Trademark of E.I. du Pont de Nemours and Company. Global G2H High-Temp 2-Wire Braid Hose Meets Flame Resistance Acceptance Designation "MSHA 2G" High-pressure hydraulic oil lines. Meets or exceeds the requirements of SAE 100R2, ISO1436 2SN R2 and EN 853 2SN. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil resistant, synthetic rubber (Hypalon - Type M). Also available with unique abrasion resistant MegaTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +275 F (-40 C to +135 C) constant and +300 F (+149 C) intermittent (up to 10% of operating time). For water emulsions see Temperature imits Table or E-crimp): Field Attachable Type T Couplings GSP Couplings (-24 and -32) MegaCrimp Couplings (-20) Hypalon is a Registered Trademark of E.I. du Pont de Nemours and Company. Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 65

67 STANDARD HYDRAUIC HOSE Information Global G2H High-Temp MegaTuff Cover High Pressure MegaTuff hose lasts up to 300 times longer than standard hose during hose-to-hose and hose-to-metal abrasion tests per ISO Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Meets Flame Resistance Acceptance Designation "MSHA 2G" High-pressure hydraulic oil lines. Meets or exceeds the requirements of SAE 100R2, ISO1436 2SN R2 and EN 853 2SN. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil and abrasion resistant, synthetic rubber and MegaTuff cover. Also available in Standard cover. See Hose Stock Characteristics. Temperature Range: -40 F to +275 F (-40 C to +135 C) constant and +300 F (+149 C) intermittent (up to 10% of operating time). For water emulsions see Temperature imits Table or E-crimp): Field Attachable Type T Couplings GSP Couplings (-24 and -32) MegaCrimp Couplings (-20) Global G2 PolarFlex Hose SAE 100R2 Type AT High Pressure Standard Hydraulic Hose Meets Flame Resistance Acceptance Designation "MSHA 2G" High-pressure hydraulic oil lines. Meets or exceeds the requirements of SAE 100R2, ISO1436 2SN R2 and EN 853 2SN. Qualified to Mil-DT Type II Class B. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil and abrasion resistant, thin synthetic rubber (Neoprene - Type A). See Hose Stock Characteristics. Temperature Range: -70 F to +212 F (-57 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): Field Attachable Type T Couplings GSP Couplings (-24 and -32) MegaCrimp Couplings (except -24 and -32) Belts Equipment 66 gates.com/mining Gates Corporation

68 High Pressure High Pressure J2AT 2-Wire Braid Jack Hose 10,000 Static Pressure Only Meets Flame Resistance Acceptance Designation "MSHA 2G" Hydraulic jack applications. Meets Material Handling Institute specification IJ 100 for hydraulic hose and assemblies used with jacking systems. 10,000 Static Pressure Only Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil and abrasion resistant, synthetic rubber (Modified Nitrile - Type C2). Also available with unique abrasion resistant MegaTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +120 F (-40 C to +49 C). For water emulsions see Temperature imits Table or E-crimp): Use MegaCrimp Male Pipe ong Nose Couplings on jack end of assembly for engagement. J2AT 2-Wire Braid Jack Hose MegaTuff Cover 10,000 Static Pressure Only MegaTuff hose lasts up to 300 times longer than standard hose during hose-to-hose and hose-to-metal abrasion tests per ISO Meets Flame Resistance Acceptance Designation "MSHA 2G" Hydraulic jack applications. Meets Material Handling Institute specification IJ 100 for hydraulic hose and assemblies used with jacking systems. 10,000 Static Pressure Only Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Black, oil and abrasion resistant, synthetic rubber and MegaTuff cover. Also available in Standard cover. See Hose Stock Characteristics. Temperature Range: -40 F to +120 F (-40 C to +49 C). For water emulsions see Temperature imits Table or E-crimp): Use MegaCrimp Male Pipe ong Nose Couplings on jack end of assembly for engagement. Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 67

69 STANDARD HYDRAUIC HOSE Information G1 1-Wire Braid Hose SAE 100R1 Type AT Medium Pressure Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Meets Flame Resistance Acceptance Designation "MSHA 2G" Medium pressure hydraulic lines. Meets or exceeds the requirements of SAE 100R1, ISO SNR1 and EN 853 1SN. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. One braid of high-tensile steel wire. Black, oil and abrasion resistant, synthetic rubber (Modified Nitrile - Type C2). See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). For water emulsions see Temperature imits Table or E-crimp): Field Attachable Type T Couplings GSP Couplings (-24 and -32) MegaCrimp Couplings (except -3, -24 and -32) Stainless Steel "B" Couplings G1H 1-Wire Braid Hose High-Temp SAE 100R1 Type AT Medium Pressure Standard Hydraulic Hose Equipment Meets Flame Resistance Acceptance Designation "MSHA 2G" Medium pressure hydraulic oil lines. Meets or exceeds requirements of SAE 100R1 Type AT. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. One braid of high-tensile steel wire. Black, oil and abrasion resistant, synthetic rubber (Hypalon - Type M). Temperature Range: -40 F to +275 F (-40 C to +135 C) constant and +300 F (+149 C) intermittent (up to 10% of operating time). For water emulsions see Temperature imits Table or E-crimp): GSP Couplings (-24 and -32) MegaCrimp Couplings (except -24 and -32) Stainless Steel "B" Couplings (-24 and -32 only) Belts Hypalon is a Registered Trademark of E.I. du Pont de Nemours and Company. 68 gates.com/mining Gates Corporation

70 Medium Pressure High Pressure RFS Red Fire Suppressant Hose Meets Flame Resistance Acceptance Designation "MSHA 2G" ow-pressure powder fire suppressant applications in mining, forestry and fire fighting equipment. The red cover is for easy visual identification in these applications. Meets performance requirements of SAE 100R1. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. One braid of high-tensile steel wire. Red, oil and abrasion resistant (Modified Nitrile - Type C2). Temperature Range: -40 F to +212 F (-40 C to +100 C) or E-crimp): MegaCrimp Couplings Power Crimp Couplings (-3 only) MegaTech II SAE 100R2 Type AT ACP Carton Pack Multi-purpose high-pressure, high-temperature, air compressor lines, petroleum-base or phosphate ester hydraulic fluid supply lines. Meets the requirements of SAE J1405 performance specifications for high-temperature transmission and lubricating oil systems using petroleum base oils. Meets or exceeds the requirements of SAE 100R2 and SAE 100R2 Type S. Black, oil resistant, synthetic rubber (CPE - Type J). See Hose Stock Characteristics. Two braids of high-tensile steel wire. Blue, oil and abrasion resistant, polyester braid. Temperature Range: -40 F to +300 F (-40 C to +149 C) or E-crimp): GSP Couplings (-24 and -32) MegaCrimp Couplings (-20 only) Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 69

71 STANDARD HYDRAUIC HOSE Information MegaTech 3000 High-Temp Oil/Air Return Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Temperature Range: MegaTech 1000 High-Temp Oil/Air Return For pressurized hot oil return lines and rotary oil lines. Meets the requirements of SAE J1405 performance specifications for high-temperature transmission and lubricating oil systems using petroleum base oils. True-bore GTS (Gates Technical Spec.) black tube specifically compounded for temperature and chemical resistance (CPE - Type J). Two braids of high-tensile steel wire or E-crimp): MegaCrimp Couplings Oil and mildew resistant, textile braid, impregnated with synthetic rubber. Petroleum-base fluids: -40 F to +300 F (-40 C to +149 C). Phosphate esters fluids as recommended by the fluid manufacturer, but within a range of -40 F to +212 F (-40 C to +100 C). Fleet Application Standard Hydraulic Hose Air brake, pressurized hot oil return lines and rotary oil/air compressor lines. Meets the requirements of DOT FMVSS , SAE J1402, for Air Brake Hose (-4, 6, 8, 10), and SAE J1405 performance specifications for hightemperature transmission and lubricating oil systems using petroleum base oils. Not recommended for gasoline or diesel fuel applications. GTS (Gates Technical Spec.) black tube specifically compounded for temperature and chemical resistance (CPE - Type J). See Hose Stock Characteristics. One braid of high-tensile steel wire. Oil and mildew resistant, textile braid, impregnated with synthetic rubber. Temperature Range: Petroleum-base fluids: -40 F to +300 F (-40 C to +149 C). Phosphate esters fluids as recommended by the fluid manufacturer, but within a range of -40 F to +212 F (-40 C to +100 C) or E-crimp): MegaCrimp Couplings Belts Equipment 70 gates.com/mining Gates Corporation

72 Fleet Application MegaTech 500 High-Temp Oil/Air Return For air brake hose, pressurized hot oil return lines and rotary oil/air compressor lines. Meets the requirements of SAE J1405 performance specifications for high-temperature transmission and lubricating oil systems using petroleum base oils. Not recommended for gasoline or diesel fuel applications. GTS (Gates Technical Spec.) black tube specifically compounded for temperature and chemical resistance (CPE - Type J). See Hose Stock Characteristics. One braid of high-tensile steel wire. Oil and mildew resistant, textile braid, impregnated with synthetic rubber. Temperature Range: Petroleum-base fluids: -40 F to +300 F (-40 C to +149 C). Phosphate esters fluids as recommended by the fluid manufacturer, but within a range of -40 F to +212 F (-40 C to +100 C) or E-crimp): G Couplings GSP Couplings (-24 and -32) MegaTech 250 High-Temp Transmission Oil Cooler (TOC) Hose High-temperature (300 F) transmission oil cooler lines, pressurized hot oil return lines and turbocharger oil supplies. Meets or exceeds SAE J1405 performance specifications for high-temperature transmission and lubricating oil systems using petroleum base oils. Not recommended for gasoline or diesel fuel applications. GTS (Gates Technical Spec.) black tube specifically compounded for temperature and chemical resistance (CPE - Type J). See Hose Stock Characteristics. One braid of high-tensile steel wire. Oil and mildew resistant, textile braid, impregnated with synthetic rubber. Temperature Range: Petroleum-base fluids: -40 F to +300 F (-40 C to +149 C). Phosphate esters fluids as recommended by the fluid manufacturer, but within a range of -40 F to +212 F (-40 C to +100 C) or E-crimp): GP Couplings (-4 through -12) MegaCrimp Couplings Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 71

73 STANDARD HYDRAUIC HOSE Information MegaTech G5TB Extreme Heat Oil/Air Return Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Temperature Range: M500 Wire Braid Hose For pressurized hot oil return lines and rotary oil lines. Meets the requirements of SAE J1405 performance specifications for high-temperature transmission and lubricating oil systems using petroleum base oils. True-bore GTS (Gates Technical Spec.) black tube specifically compounded for temperature and chemical resistance (CPE - Type J). Two braids of high-tensile steel wire or E-crimp): G Couplings (-24 and -32 only) MegaCrimp Couplings Blue, oil and mildew resistant textile braid, impregnated with synthetic rubber. Petroleum-base fluids: -40 F to +300 F (-40 C to +149 C). Phosphate esters fluids as recommended by the fluid manufacturer, but within a range of -40 F to +212 F (-40 C to +100 C). ow Pressure Standard Hydraulic Hose Meets Flame Resistance Acceptance Designation "MSHA 2G" Pilot lines, grease lines and pressure return lines, 500 psi or less pressure applications. Black, oil resistant, synthetic rubber (NBR). One braid of high-tensile steel wire. Black, oil and abrasion resistant, synthetic rubber, flame resistance. Also available with unique abrasion resistant XtraTuff cover. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C) or E-crimp): GP Couplings MegaCrimp Couplings Belts Equipment 72 gates.com/mining Gates Corporation

74 ow Pressure M500-XTF M500 XtraTuff Wire Braid Meets Flame Resistance Acceptance Designation "MSHA 2G" Pilot lines, grease lines and pressure return lines, 500 psi or less pressure applications. Black, oil resistant, synthetic rubber (NBR). One braid of high-tensile steel wire. Black, oil and abrasion resistant, synthetic rubber, flame resistance. Also available in Standard cover. See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C) or E-crimp): GP Couplings MegaCrimp Couplings TR500 High-Temp/Air Brake/Engine Hose Air brake hose, high temperature pressurized oil return lines and rotary oil/air compressor lines, engine and transmission coolant lines and lube oil lines. Meets or exceeds DOT FMVSS , SAE J1402 for air brake hose (4, 6, 8, 10). Not recommended for gasoline or diesel fuel applications. Black (Nitrile - Type C). See Hose Stock Characteristics. One braid of high-tensile steel wire. Oil and mildew resistant, textile braid, impregnated with synthetic rubber. Temperature Range: -40 F to +250 F (-40 C to +121 C) or E-crimp): GP Couplings MegaCrimp Couplings Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 73

75 STANDARD HYDRAUIC HOSE Information G3H High-Temp 2-Fiber Braid Hose SAE 100R3 Medium Pressure Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Hydraulic oil lines, anti-freeze solutions or water. Meets or exceeds requirements of SAE 100R3. Temperature Range: Black, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Two fiber braids. Black, oil and abrasion resistant, synthetic rubber (Neoprene - Type A). See Hose Stock Characteristics. For hydraulic oil lines -40 F to +275 F (-40 C to +135 C) constant and +300 F (+149 C) intermittent (up to 10% of operating time) or E-crimp): MegaCrimp Couplings (-4, -6, -8, -10) GTH High-Temp 1-Fiber Braid Hose SAE 100R6 ow Pressure Standard Hydraulic Hose Temperature Range: Hydraulic oil lines, heavy-duty transmission oil cooler lines and glycol anti-freeze solutions. Meets or exceeds requirements of SAE 100R6. Black, specially compounded, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. One fiber braid. Black, oil and abrasion resistant, synthetic rubber (Neoprene - Type A). See Hose Stock Characteristics. For hydraulic oil lines -40 F to +275 F (-40 C to +135 C) constant and +300 F (+149 C) intermittent (up to 10% of operating time) or E-crimp): GP Couplings (except -3 and -5) MegaCrimp Couplings (except -3) Power Crimp Couplings (-3 only) Belts Equipment 74 gates.com/mining Gates Corporation

76 ow Pressure ow Pressure GTHX High-Temp Fiber Spiral Hose SAE 100R6 Hydraulic oil lines, heavy-duty transmission oil cooler lines and glycol anti-freeze solutions. Meets or exceeds requirements of SAE 100R6. Black, specially compounded, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Spiraled synthetic fiber. Black, oil and abrasion resistant, synthetic rubber (Neoprene - Type A). See Hose Stock Characteristics. Temperature Range: For hydraulic oil lines -40 F to +275 F (-40 C to +135 C) constant and +300 F (+149 C) intermittent (up to 10% of operating time) or E-crimp): GP Couplings MegaCrimp Couplings GMV Global MegaVac Return ine and Suction Hose Meets Flame Resistance Acceptance Designation "MSHA 2G" Petroleum and water-base hydraulic fluids in suction lines or in low pressure return lines. Meets or exceeds requirements of SAE 100R4. Uses half the bend radius of SAE 100R4. Meets marine ABS with use of HeatGuard high temp sleeve. Black, synthetic rubber is specifically designed for resistance to high temperatures (Nitrile - Type C). See Hose Stock Characteristics. Double spiral textile (braid for -12, -16 and -20) reinforced with a helical spiral-wire to prevent collapse. Black synthetic rubber is oil and abrasion resistant (Neoprene - Type A). See Hose Stock Characteristics. Temperature Range: -40 F to +275 F (-40 C to +135 C) constant and +300 F (+149 C) intermittent (up to 10% of operating time) or E-crimp): G Couplings MegaCrimp Couplings (-12 through -20) Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 75

77 STANDARD HYDRAUIC HOSE Information G4H MegaVac Return ine and Suction Hose ow Pressure Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Meets Flame Resistance Acceptance Designation "MSHA 2G" Petroleum and water-base hydraulic fluids in suction lines or in low pressure return lines. Meets or exceeds requirements of SAE 100R4 (except 1" I.D.). Uses half the bend radius of SAE 100R4. Black, synthetic rubber is specifically designed for resistance to high temperatures (Nitrile - Type C). See Hose Stock Characteristics. Double spiral textile reinforced with a helical spiral-wire to prevent collapse. Black synthetic rubber is oil and abrasion resistant (Neoprene - Type A). See Hose Stock Characteristics. Temperature Range: -40 F to +275 F (-40 C to +135 C) constant and +300 F (+149 C) intermittent (up to 10% of operating time) or E-crimp): G Couplings MegaCrimp Couplings Use clamp over beaded nipple. RA 1-Fiber Braid Return ine and ow Pressure Hose ow Pressure Standard Hydraulic Hose Meets Flame Resistance Acceptance Designation "MSHA 2G" ow-pressure hydraulic oil return lines for general purpose water, glycol antifreeze solutions, conveying diesel fuel, gasoline or air. Meets SAE 30R2 performance requirements of both Type 1 and Type 2 for fuel and B20 constant contact up to 125 F biodiesel fuel transfer applications. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. One fiber braid (-3 to -10). Spiral braid (-12 to -16). Black, synthetic rubber. Oil and abrasion resistant (Modified Nitrile - Type C2). See Hose Stock Characteristics. Temperature Range: -40 F to +212 F (-40 C to +100 C). Air to +160 F (+71 C) only or E-crimp): GP Couplings (except -3, -5 and -16) MegaCrimp Couplings (except -3) Power Crimp Couplings (-3 only) Belts Equipment 76 gates.com/mining Gates Corporation

78 ow Pressure ow Pressure RC 3-Fiber Braid Return ine and ow Pressure Hose Petroleum-base hydraulic oils, glycol antifreeze, air or water in low pressure fluid transfer or hydraulic system return lines. Generally connected to 100R4 stems, beaded nipples, or tube type ports with worm gear clamps. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. Three fiber braids. Black, oil and abrasion resistant, synthetic rubber (Modified Nitrile - Type C2). See Hose Stock Characteristics. Temperature Range: For hydraulic oil lines -40 F to +275 F (-40 C to +135 C) constant and +300 F (+149 C) intermittent (up to 10% of operating time); air to +160 F (+71 C) only. For water emulsions see Temperature imits Table or E-crimp): Use barbed stem or beaded-tube with clamps only. MegaTech OC 1-Fiber Braid High-Temp ock-on Hose High-temperature (300 F) transmission oil cooler lines, pressurized hot oil return lines and turbocharger oil supply lines. Meets or exceeds SAE J1405 performance specifications for high-temperature transmission and lubricating oil systems using petroleum base oils. Not recommended for gasoline or diesel fuel applications. True-bore GTS (Gates Technical Spec.) black tube specifically compounded for temperature and chemical resistance (CPE - Type J). One fiber braid. Oil and mildew resistant, textile braid, impregnated with synthetic rubber. Temperature Range: -40 F to +300 F (-40 C to +149 C) or E-crimp): Field Attachable OC Couplings GP Couplings (-4 to -12) MegaCrimp Couplings (-16) Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 77

79 STANDARD HYDRAUIC HOSE Information OC 1-Fiber Braid ock-on Hose ow Pressure Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Petroleum-base hydraulic oils, glycol antifreeze compounds, water, engine lubricating oils and air. ock-on hose and couplings are NOT recommended for vibration or pressure surge applications, such as permanent piping in residential or commercial buildings. Meets SAE 30R2, SAE 30R6 and SAE 30R7 performance requirements for fuel and B20 biodiesel fuel transfer applications up to +125 F. Black, oil resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. One fiber braid. Oil and mildew resistant, textile braid, impregnated with synthetic rubber. Temperature Range: -40 F to +250 F (-40 C to +121 C). For air: -40 F to +160 F (-40 C to +71 C) or E-crimp): Field Attachable OC Couplings GP Couplings O Plus ock-on Hose ow Pressure Standard Hydraulic Hose Black Cover Only Meets Flame Resistance Acceptance Designation "MSHA 2G" Petroleum-base hydraulic oils, water, glycol antifreeze solutions, engine lubricating oils, and air. ock-on hose and couplings are NOT recommended for pressure surge applications or critical applications, such as permanent piping in residential or commercial buildings. Do not use for gasoline or diesel fuels, unless approved by Gates H/C Application. Black, oil resistant, synthetic rubber highly resistant to oil and heat (Nitrile - Type C). See Hose Stock Characteristics. One fiber braid. Oil and abrasion resistant synthetic rubber (Modified Nitrile - Type C2). Available in black Neoprene (OA), blue (OB), green (OG), red (OR), yellow (OY) and gray (OC) colors. Temperature Range: -40 F to +212 F (-40 C to +100 C). Air to +160 F (+71 C) only or E-crimp): Field Attachable OC Couplings GP Couplings (except -3) Use clamp over beaded nipple. Belts Equipment 78 gates.com/mining Gates Corporation

80 C5C Hydraulic Hose SAE 100R5 Medium pressure hydraulic petroleum-based oil lines in impulse applications, lube oil, air and water in applications such as air brakes, power steering (CAUTION: Intended for heavy-duty commercial vehicle use only), turbocharger oil supplies, tilt cab cylinders, transmission coolant and filtration lines. Meets or exceeds requirements of SAE 100R5 for traditional hydraulic applications, DOT FMVSS Type AII and SAE J1402 Type AII for air brake applications (-4 to -12). Not recommended for gasoline or diesel fuel. -4 and -5: black, oil and heat resistant synthetic rubber (Neoprene - Type A); -6 through -40: (Nitrile - Type C). See Hose Stock Characteristics. One braid of high-tensile carbon steel wire over one braid of polyester. Black, oil and mildew resistant, polyester braid. Temperature Range: Under SAE 100R5 (hydraulic) conditions -40 F to +212 F (-40 C to +100 C). All-purpose fleet application (hot lube oil lines) -40 F to +300 F (-40 C to +149 C). Air to +160 F (+71 C) only. Avoid continuous use at maximum temperature concurrent with maximum working pressures or E-crimp): C5 Field Attachable Coupling C5D High-Temp Multi-Fluid Hose Petroleum-base or phosphate ester fluids; diesel fuels and filtration lines, transmission coolant lines, hot lube oil lines, power steering (CAUTION: Intended for heavy-duty commercial vehicle use only), gasoline and turbocharger oil supplies. Tilt cab cylinder and air brakes. C5D (-4 to -12) meets or exceeds DOT FMVSS Type All, SAE J1402 Type All and SAE J1405 and fuel resistance of SAE J30R2. Not approved for bio diesel. Black, oil and heat resistant, synthetic rubber (CPE - Type J). See Hose Stock Characteristics. One braid of high-tensile steel wire over one braid of polyester. Green for easy identification, oil and mildew resistant, polyester braid impregnated with synthetic rubber. Temperature Range: -40 F to +300 F (-40 C to +149 C). Air to +250 F (+121 C) only, maximum phosphate esters to +212 F (+100 C) or E-crimp): C5 Field Attachable Couplings Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 79

81 STANDARD HYDRAUIC HOSE Information C5M Marine Fuel ine Hose Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Meets Flame Resistance Acceptance Designation "MSHA 2G" On-shore/off-shore and marine diesel fuel and gasoline applications and hot oil lines up to +212 F. Meets USCG marine fuel line specifications, SAE J1527 B100 to +125 F Type A Class 1 and SAE J1942 requirements. Exceeds performance requirements of SAE J30R2 for non-marine applications. Nitrile - Type C. See Hose Stock Characteristics. One wire braid Modified Nitrile - Type C2. Blue. See Hose Stock Characteristics. Temperature Range: -4 F to +212 F (-20 C to +100 C) or E-crimp): C5 Field Attachable Couplings C5E High-Temp Flexline Hose DOT FMVSS 106 Type A1, SAE J1405 and SAE J1402 Type A1 (-4 to -12). Standard Hydraulic Hose Air brake hose, power steering (CAUTION: Intended for heavy-duty commercial vehicle use only), fuel filter, engine and transmission coolant lines, and hot (+300 F) lube oil lines. Black, oil and heat resistant, synthetic rubber (Nitrile - Type C). See Hose Stock Characteristics. One braid of high-tensile steel wire over one braid of polyester. Black, oil and heat resistant, textile braid impregnated with synthetic rubber. Green stripe for easy identification. Temperature Range: -40 F to +300 F (-40 C to +149 C). Air +250 F (+121 C) maximum only. For water emulsions see Temperature imits Table or E-crimp): C5E Field Attachable Couplings Belts Equipment 80 gates.com/mining Gates Corporation

82 Cover/ Temperature Range: C or E-crimp): C14 Couplings Nylon Air Brake Tubing Truck, bus and mobile air brake, and service lines where heat and battery acids are not present. Conforms to SAE J844 specifications. Meets D.O.T. FMVSS Heat and light stabilized seamless extruded nylon. Type A: Non-reinforced in sizes 1/8", 5/32", 3/16" and 1/4". NOTE: 1/8" and 5/32" are NOT recognized by D.O.T. for air brake systems, these are for service lines only. Type B: Reinforced with one open ply of fibrous nylon in sizes 5/16", 3/8", 1/2", 5/8" and 3/4". Nylon. Available in black (NABTA), blue (NABTB), green (NABTG), red (NABTR), yellow (NABTY), orange (NABTO), purple (NABTP), brown (NABTN), silver (NABTS) and white (NABTW) colors. Other colors available upon request. Temperature Range: -40 F to +200 F (-40 C to +93 C) or E-crimp): Gates DOT Sureok Couplings C14 PTFE Hose SAE 100R14 Type A Nonconductive Air compressor discharge, hot oil and fluids, hot and greasy environments. One braid of 300 Series stainless steel wire. Dynamic: -65 F to +400 F (-54 C to +204 C). Static: -65 F to +450 F (-54 C to +232 C). Type A-Nonconductive white, smooth bore Polytetrafluoroethylene (PTFE). See Hose Stock Characteristics. Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 81

83 STANDARD HYDRAUIC HOSE Information C14CT PTFE Hose SAE 100R14 Type B Conductive Specialized Mining Hose Cover/ Temperature Range: C14CT or E-crimp): C14 Couplings Air compressor discharge, hot oil and fluids, hot and greasy environments. One braid of 300 Series stainless steel wire. Dynamic: -65 F to +400 F (-54 C to +204 C). Static: -65 F to +450 F (-54 C to +232 C). Type B-Conductive black/white smooth bore Polytetrafluoroethylene (PTFE). See Hose Stock Characteristics. Specialized Mining Couplings, Adapters and Accessories TH8 Hydraulic Hose SAE 100R8 Thermoplastic Standard Hydraulic Hose Use with petroleum, water base and synthetic hydraulic fluids. Applications include: power and telephone mobile equipment (cherry pickers), lubrication lines, blowout preventer control lines, hydraulic lifts and farm and construction machinery. TH8 hose meets or exceeds performance requirements of SAE 100R8 with a significantly tighter bend radius. Multiline available. 100% seamless Nylon - Type Z that easily handles a broad range of hydraulic fluids, including phosphate esters and water glycol. See Hose Stock Characteristics. Two polyester braids. Black urethane resists hydraulic fluids, high temperatures, aging and weathering. Black TH8 cover is perforated for use in general hydraulic and pneumatic service. Temperature Range: -65 F to +200 F (-54 C to +93 C) continuous service for petroleum and synthetic oils. Maximum of +158 F (+70 C) for water, water/oil emulsions and water glycol or E-crimp): MegaCrimp Couplings (-4 through -16) Swage PCTS Couplings (-3 only) Belts Equipment 82 gates.com/mining Gates Corporation

84 Thermoplastic Thermoplastic TH8NC Non Conductive Hydraulic Hose SAE 100R8 Use with petroleum, water base and synthetic hydraulic fluids. Applications include: power and telephone mobile equipment (cherry pickers), lubrication lines, blowout preventer control lines, hydraulic lifts and farm and construction machinery. TH8NC hose (orange cover) meets SAE 100R8 non-conductivity requirements. TH8NC hose meets or exceeds performance requirements of SAE 100R8 with a significantly tighter bend radius. Multiline available. 100% seamless Nylon - Type Z that easily handles a broad range of hydraulic fluids, including phosphate esters and water glycol. See Hose Stock Characteristics. Two polyester braids. Orange urethane resists hydraulic fluids, high temperatures, aging and weathering. TH8NC is non-perforated for applications requiring electrical non-conductivity. Meets SAE 100R8 Electrical Conductivity Test. Maximum leakage shall not exceed 50 microamperes when subjected to 75 kv/ft. for five minutes. (Orange is industry accepted color for non-conductive hose). Temperature Range: -65 F to +200 F (-54 C to +93 C) continuous service for petroleum and synthetic oils. Maximum of +158 F (+70 C) for water, water/oil emulsions and water glycol or E-crimp): MegaCrimp Couplings TH7 Hydraulic Hose SAE 100R7 Petroleum, water base and synthetic hydraulic fluids. Applications include: power and telephone mobile equipment (cherry pickers), lubrication lines, blowout preventer control lines, hydraulic lifts and farm and construction machinery. TH7 hose meets or exceeds performance requirements of SAE 100R7 with a significantly tighter bend radius. 100% seamless Nylon - Type Z that easily handles a broad range of hydraulic fluids, including phosphate esters and water glycol. See Hose Stock Characteristics. Braided synthetic fiber (-2, -8, -12 and -16). Spiraled synthetic fiber (-3, -4, -5 and -6). Black polyurethane that resists hydraulic fluids, high temperatures, aging and weathering. Black TH7 is perforated for use in general hydraulic and pneumatic service. Temperature Range: -65 F to +200 F (-54 C to +93 C) continuous service for petroleum and synthetic oils. Maximum of +158 F (+70 C) for water, water/oil emulsions and water glycol or E-crimp): MegaCrimp Couplings Swage PCTS Couplings (-2 and -3) Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 83

85 STANDARD HYDRAUIC HOSE Information TH7NC Non Conductive Hydraulic Hose SAE 100R7 Thermoplastic Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Petroleum and synthetic hydraulic fluids. Applications include: power and telephone mobile equipment (cherry pickers), lubrication lines, blowout preventer control lines, hydraulic lifts and farm and construction machinery. Orange color TH7NC meets SAE 100R7 nonconductivity requirements and meets or exceeds performance requirements of SAE 100R7 with a significantly tighter bend radius. Meets ANSI A92.2 for vehicle mounted aerial devices (-4 to -8). -2, -12, and -16: 100% seamless Nylon - Type Z that easily handles a broad range of hydraulic fluids, including phosphate esters and water glycol; -3 through -8 Polyester. See Hose Stock Characteristics. Braided synthetic fiber (except -2: Spiraled synthetic fiber). Orange urethane that resists hydraulic fluids, high temperatures, aging and weathering. Orange TH7NC is nonperforated for applications requiring electrical non-conductivity. Meets SAE 100R7 Electrical Conductivity Test. Maximum leakage shall not exceed 50 microamperes when subjected to 75 kv/ft. for five minutes. (Orange is industry accepted color for non-conductive hose). Temperature Range: -65 F to +200 F (-54 C to +93 C) continuous service for petroleum and synthetic oils. Maximum of +158 F (+70 C) for water, water/oil emulsions and water glycol or E-crimp): MegaCrimp Couplings Swage PCTS Couplings (-2 and -3) TH7D Dual ine Hydraulic Hose SAE 100R7 Thermoplastic Standard Hydraulic Hose Equipment Belts Petroleum, water base and synthetic hydraulic fluids. Applications include: power and telephone mobile equipment (cherry pickers), lubrication lines, blowout preventer control lines, hydraulic lifts and farm and construction machinery. TH7D hose meets or exceeds performance requirements of SAE 100R7 with significantly tighter bend radius. 100% seamless Nylon - Type Z that easily handles a broad range of hydraulic fluids, including phosphate esters and water glycol. See Hose Stock Characteristics. Spiraled synthetic fiber. Black polyurethane that resists hydraulic fluids, high temperatures, aging and weathering. Black TH7D is perforated for use in general hydraulic and pneumatic service. Temperature Range: -65 F to +200 F (-54 C to +93 C) continuous service for petroleum and synthetic oils. Maximum of +158 F (+70 C) for water, water/oil emulsions and water glycol or E-crimp): MegaCrimp Couplings 84 gates.com/mining Gates Corporation

86 Thermoplastic Thermoplastic TH7NCD Non Conductive Dual ine Hydraulic Hose SAE 100R7 Petroleum, water base and synthetic hydraulic fluids. Applications include: power and telephone mobile equipment (cherry pickers), lubrication lines, blowout preventer control lines, hydraulic lifts and farm and construction machinery. Orange color TH7NCD meets SAE 100R7 non-conductivity requirements and meets or exceeds performance requirements of SAE 100R7 with significantly tighter bend radius. Meets ANSI A92.2 for vehicle mounted aerial devices (-3 and -8). Polyester. Braided synthetic fiber. Orange urethane that resists hydraulic fluids, high temperatures, aging and weathering. Orange TH7NCD is nonperforated for applications requiring electrical non-conductivity. Meets SAE 100R7 Electrical Conductivity Test. Maximum leakage shall not exceed 50 microamperes when subjected to 75 kv/ft. for five minutes. (Orange is industry accepted color for non-conductive hose.) Temperature Range: -65 F to +200 F (-54 C to +93 C) continuous service for petroleum and synthetic oils. Maximum of +158 F (+70 C) for water, water/oil emulsions and water glycol or E-crimp): MegaCrimp Couplings TH18 Constant Pressure Hydraulic Hose SAE 100R18 TH18 hose meets or exceeds performance requirements of SAE 100R18 with a significantly tighter bend radius. Suitable for petroleum or synthetic-based hydraulic fluids in hydraulic systems. TH18 is ideal for industrial and agricultural applications exposed to low temperatures or cyclic and quick temperature changes. Remains highly flexible in cold weather conditions and is resistant to hydraulic fluids, high temperatures, aging and weathering. Polyester elastomer. One band of synthetic fiber. Black, special polyester, perforated. Temperature Range: -67 F to +212 F (-55 C to +100 C) continuous service for petroleum and synthetic oils. Maximum of +158 F (+70 C) for water-based fluids or E-crimp): MegaCrimp Couplings Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 85

87 STANDARD HYDRAUIC HOSE Information TH18NC Constant Pressure Non Conductive Hydraulic Hose SAE 100R18 Thermoplastic Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories TH18NC hose meets or exceeds performance requirements of SAE 100R18 with a significantly tighter bend radius. Suitable for petroleum or synthetic-based hydraulic fluids in hydraulic systems. TH18NC non-conductive hoses are suitable for use in high-voltage applications. Remains highly flexible in cold weather conditions and is resistant to hydraulic fluids, high temperatures, aging and weathering. Polyester elastomer. Two bands of synthetic fiber. Special polyester, orange (industry-accepted color for non-conductive hose), non-perforated for applications requiring electrical non-conductivity. Meets SAE 100R18 Electrical Conductivity Test. Maximum leakage shall not exceed 50 microamperes when subjected to 75kV/ft for five minutes. Temperature Range: -67 F to +212 F (-55 C to +100 C) continuous service for petroleum and synthetic oils. Maximum of +158 F (+70 C) for water-based fluids or E-crimp): MegaCrimp Couplings PolarSeal Hose (SAE J51, Type A2 Dimensions; SAE J51, Type D Performance; SAE J2064, Type C, Class II Performance). Refrigerant Standard Hydraulic Hose iquid and gaseous R134a and R12 refrigerants in automotive air conditioning and industrial systems; i.e., tractors, construction trucks, mobile and stationary refrigeration units. Designed to minimize permeation of R134a refrigerant. Black, synthetic rubber (Chloroprene - Type A). See Hose Stock Characteristics. Two layers of spiral polyester. Black synthetic rubber (EPDM). See Hose Stock Characteristics. Temperature Range: -22 F to +257 F (-30 C to +125 C). Barrier: Nylon liner or E-crimp): PolarSeal Couplings Belts Equipment 86 gates.com/mining Gates Corporation

88 Refrigerant PolarSeal II Hose AC systems on School/Transit Busses, RV's, imos and other heavy equipment that has long run or hard to service AC lines. iquid and gaseous R134a and R12 refrigerants in automotive air conditioning and industrial systems; i.e., tractors, construction trucks, mobile and stationary refrigeration units. Designed to minimize permeation of R134a refrigerant. Black, synthetic Elastomeric rubber. Fabric Braid Heat, Moisture and Ozone resistant black synthetic Elastomeric cover. Temperature Range: -22 F to +257 F (-30 C to +125 C). Barrier: Nylon liner or E-crimp): PolarSeal II Coupling Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 87

89 Information EQUIPMENT In the shop or in the field, Gates has a crimper for every job. MobileCrimp 4-20 he latest in high tech crimping. T Portable and lightweight only 57 pounds. n Powerful enough to crimp up to 1-1/4" I.D. four spiral-wire hose. n Great for jobs in the field. n n Specialized Mining Hose FOR SAFETY S SAKE Power Crimp 707 he most precise, yet simplest crimper made. T The first crimper with electronic digital readout to indicate crimp diameter setting. n Crimps low pressure return lines to high pressure spiral hoses, from 3/16" to 1-1/4" I.D. four-spiral wire. n Crimps straight and bent tube couplings, plus 45 and 90 block types. n S wage capable. n Specialized Mining Couplings, Adapters and Accessories n SC-32 Crimper Compact design to minimize space required. High-ton ram force with an integrated pump. n Pump pre-wired for either 110 Volt or 220 Volt (1 phase) outlets. n Bottom-loading makes crimping easier. n Come with all the base plates and spacers required to crimp up to 2" hoses. n n GC32-XD Crimper n C rimps every hose and coupling in the Gates hydraulic catalog, including 2-1/2" Global MegaVac return lines. n Standard Hydraulic Hose n n n Accepts electrical input from 208 volts to 260 volts, single phase. T wice as fast as the Gates OmniCrimp 21 crimper, which the GC32-XD is replacing. P atented quick change tool enables fast loading and unloading of color-coded, numbered dies Radial Ton crimping force GC96 Crimper Equipment n E lectronic touch screen control panel for fast input of crimper settings. n H orizontal front-end feed makes crimping easier and convenient. n 3 40 ton force that allows crimping of a wide variety of couplings. n 2 speed die closure and rapid retract permit fast assembly fabrication. n Belts n F ull range die sets that enable production of a wide range of hose assemblies. 2 " 6 wire and 6" industrial For complete crimper specifications, see the following pages. 88 gates.com/mining Gates Corporation

90 MobileCrimp This lightweight, versatile crimper is powerful enough to crimp up to 1-1/4" four spiral-wire hose Weighing approximately 57 pounds, this new field crimper combines the latest crimping technology with oldfashioned toughness and durability. Digital Dial Control Just dial in appropriate crimp setting and hold the start button until light comes on and buzzer sounds, then release. Ability to lock-in setting for multiple assemblies. ight and buzzer operate on two "AAA" batteries. Number: Accessories MobileCrimp 4-20 Die Selection Table For MegaCrimp (G25) Couplings 4-20 Crimper Hose Sizes Hose Type 1/4" 3/8" 1/2" 5/8" 3/4" 1" 1-1/4" M3K MC21 or MC31 MC22 or MC32 MC33 MC34 MC35 MC37 M2T MC21 or MC31 MC22 or MC32 MC33 MC34 MC35 MC37 G1 MC21 or MC31 MC22 or MC32 MC33 MC34 MC35 MC37 MC39 G2 MC21 or MC31 MC22 or MC32 MC33 MC34 MC35 MC37 MC39 For other hose and coupling configurations, reference or Gates crimp data manual. Number Crimper-to-Pump Male Quick Disconnect Crimper-to-Pump Female Quick Disconnect Die Sets (ordered separately) For GlobalSpiral (G20) Couplings Hose Sizes Hose Type 3/8" 1/2" 5/8" 3/4" 1" 1-1/4" EFG6K MC33 MC33 MC35 MC35 MC37 EFG5K MC33 MC33 MC35 MC35 MC37 EFG4K MC33 MC33 MC35 MC35 MC37 MC39* *MGS (G21 series) couplings only. Die Set MC21/MC31 MC22/MC32 MC33 MC34 MC35 MC37 MC / / FOR SAFETY S SAKE Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 89

91 EQUIPMENT Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories MobileCrimp 4-20 Power Sources Wide selection of pumps to match all your power needs. Shop Air Pump Works off standard shop air (90 psi). Economical, convenient and versatile for use wherever 90 psi compressed air is available. Number: Pressure Rating: 10,000 psi Weight: 10 lbs. Hand Pump No power source needed. Economical, convenient and portable for use anywhere. Make factory-quality assemblies in the field to minimize downtime. Number: Pressure Rating: 10,000 psi Weight: 25.6 lbs. 1/2 HP 115 Volt AC Pump Medium speed. Economical. Recommended for a stationary or mobile application. Number: Pressure Rating: 10,000 psi Weight: 32 lbs. Standard Hydraulic Hose 1-1/2 HP 115 Volt AC Pump High speed. Recommended for stationary applications only. Number: Pressure Rating: 10,000 psi Weight: 108 lbs. Equipment Belts 1/4 HP 12 Volt DC Pump Mobile operation, runs on standard 12 volt car/truck battery or a 12 volt portable battery pack. Ideal for tough jobs in the field. Number: Pressure Rating: 10,000 psi Weight: 20.5 lbs. 90 gates.com/mining Gates Corporation

92 Power Crimp 707 Gates Power Crimp 707 is the most precise, yet simplest crimper made. It was the first crimper with electronic digital readout to indicate gauge setting. The toughest part about using the 707 is pushing a button. It takes just a few seconds to make factoryquality hose assemblies. Crimps most hydraulic hoses from low pressure return lines to extremely high pressure spirals, from 3/16" to 1-1/4" I.D. Crimps straight and bent tube couplings, plus 45 and 90 block types. Can also be adapted for use as a power swager. Power Crimp 707 Die Selection Table Power Crimp Power Source The flows of two fixed displacement pumps are combined to deliver a high volume of oil at low pressure for fast transversion. SPECIFICATIONS SPECIFICATIONS Number: Standard PC707 without die sets wired for 115 volts (includes die backup ring and a notched cone). ion Rate: 100 assemblies per hour (using 1/2" I.D. two-wire straight thread assemblies). Dimensions: 13" wide by 12" deep by 26-1/2" high. Weight: 188 lbs. PC V Converter Kit Converts crimper and pump Number: For MegaCrimp (G25) Couplings For GlobalSpiral (G20) Couplings Hose Sizes Hose Type 1/4" 3/8" 1/2" 5/8" 3/4" 1" 1-1/4" M3K 721 or or M2T 721 or or G1 721 or or G2 721 or or For other hose and coupling configurations, reference or Gates crimp data manual. Die Sets (ordered separately) Die Set 721/ / * 739* / / * Must Use No-Notch Die Cone. Die Cones: No-Notch Number: Notched Number: Hose Sizes Hose Type 3/8" 1/2" 5/8" 3/4" 1" 1-1/4" EFG6K EFG5K EFG4K Number: (115 volt, 30 amp, circuit, 1 h.p., 60 cycles) Dimensions: 12" wide by 25" deep by 12" high. Weight: 70 lbs. Maximum Working Pressure: 4,900 psi. PC V Converter Kit Converts crimper and pump Number: Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 91

93 EQUIPMENT Information Specialized Mining Hose SC32 Crimper The Gates SC32 crimper is a versatile, easy-touse, economical machine suitable for a hardworking shop environment. It is offered in 110V and 220V single phase versions to match the shop power supply. This rugged crimper is designed for continued use to meet day-to-day shop and counter needs for crimps on hoses up to 1-1/4" I.D. with occasional crimps for larger assemblies up to 2", 6-spiral hose. Number: Wired for 220 Volts with 2 HP electric pump Number: Wired for 110 Volts with 1 HP electric pump Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose SPECIFICATIONS Dimensions: 16.5" W x 32" D x 29" H Max. Rated Working Pressure: 10,000 psi Max. Crimping Force: 80 tons Weight: 275 Pounds Warranty: 2 Years SC32 Die Selection Table For GlobalSpiral (G20) Couplings Hose Sizes Hose Type 3/8" 1/2" 5/8" 3/4" 1" 1 1/4" EFG3K EFG4K EFG5K For MegaCrimp (G25) Couplings Hose Sizes Hose Type 1/4" 3/8" 1/2" 5/8" 3/4" 1" 1-1/4" M3K 721 or or M2T 721 or or G1 721 or or G2 721 or or Die Sets (ordered separately) For GSP & GSH Couplings Hose Sizes Hose Type 1-1/2" 2" EFG6K SC EFG5K SC SC-314 EFG3K SC SC-313 G1H SC32-310() SC-313 G2H SC32-310() SC-312 For other hose and coupling configurations, reference or Gates crimp data manual. Die Set SC32-21/31 SC32-22/32 SC32-33 SC32-34 SC32-35 SC32-37* SC32-39* / / Die Set SC SC SC SC SC supersedes 310 die. * Must Use No-Notch Die Cone. Belts Equipment 92 gates.com/mining Gates Corporation

94 GC32-XD Die Set Die Set Die Set Die Set Die Set Die Set Crimper The new GC32-XD crimper from Gates crimps every hose and coupling in our hydraulics catalog fast. The open crimper head accommodates any Gates hose construction or coupling configuration, including 2-1/2" Global MegaVac return lines. And it makes them at a rate that's twice as fast as the Gates OmniCrimp 21 crimper, which the GC32-XD is replacing. Internally, the GC32-XD uses a unique cloverleaf* design that simply produces a better crimp. Unlike standard annular head configurations, Gates exclusive cloverleaf design reinforces the piston so the dies move smoother for more consistent crimps without any taper in the crimp OD. GC32 -XD Crimper For GlobalSpiral (G20) Couplings Die Sets (ordered separately) SPECIFICATIONS Number: Dimensions: 37" high by 23" wide by 19-1/2" deep Weight: 660 lbs. Motor: 5 hp Pump: 2-stage Power Source: V, Hz, 1 phase and 20 Amps Maximum Operating Pressure: 470 tons Stand: (Optional): 25-1/2" high by 31-3/4" wide by 16-1/2" deep (height adjustable) *Patent pending Rack and stand sold separately For GSP & GSH Couplings Hose Sizes Hose Sizes Hose Type 3/8" 1/2" 5/8" 3/4" 1" 1-1/4" Hose Type 1-1/2" 2" EFG6K EFG6K G5K EFG5K C12M EFG3K G1H () For MegaCrimp (G25) Couplings G2H () Hose Sizes Hose For ifeguard Sleeving Type 1/4" 3/8" 1/2" 5/8" 3/4" 1" 1-1/4" M3K or or /4" 3/8" 1/2" M2T or or G or or /8" 3/4" 1" G or or For other hose and coupling configurations, reference or Gates crimp data manual. Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 93

95 EQUIPMENT Information Specialized Mining Hose GC96 Crimper The GC 96 crimper is capable of crimping 2" 6 wire and up to 6" ID industrial hose. This crimper allows distributors to make reliable and professional looking assemblies providing more value to the end user. The large crimper head allows industrial hose assemblies to be made with a variety of terminations using crimpable ferrules and sleeves. The GC96 crimper has additional versatility since in conjunction with optional spacer dies and GC32-XD dies; it can make Gates hydraulic hose assemblies also. SPECIFICATIONS Number: Dimensions: 31" high by 32" wide by 16" deep Weight: 650 lbs. Power Source: V, Hz, single phase and 20 amps Capability: 1/4" 2" Hydraulic hose 2-1/2" 4" Industrial hose 5" 6" Industrial hose up to and including 100 PSI WP Specialized Mining Couplings, Adapters and Accessories GC96 Crimper For GlobalSpiral (G20) Couplings Hose Sizes Hose Type 3/8" 1/2" 5/8" 3/4" 1" 1-1/4" EFG6K G5K C12M For MegaCrimp (G25) Couplings Hose Sizes Hose Type 1/4" 3/8" 1/2" 5/8" 3/4" 1" 1-1/4" M3K or or M2T or or G or or G or or For other hose and coupling configurations, reference or Gates crimp data manual. For GSP & GSH Couplings Hose Sizes Hose Type 1-1/2" 2" EFG6K EFG5K EFG3K G1H () G2H () For ifeguard Sleeving 1/4" 3/8" 1/2" /8" 3/4" 1" Standard Hydraulic Hose Equipment Belts Die Sets (ordered separately) Die Set Die Set Die Set Die Set Die Set Die Set gates.com/mining Gates Corporation

96 xxx xxxxx xxx PolarSeal Number: Hose Portable Crimper II Gates portable PolarSeal Crimper II is a hand-operated hose crimping machine specifically designed for crimping Gates PolarSeal couplings and is intended for use with Gates PolarSeal refrigerant hose. Standard dies included will crimp 5/16" (-6 Black), 13/32" (-8 Blue), 1/2" (-10 Green) and 5/8" (-12 Clear) sizes. Features: n Portable hand operation, easy to change over from size to size. n Heavy-duty construction for use with air impact wrenches. n Crimps two-braid dimension or nylon barrier hose. n OE-style bubble crimp. n Quick-change dies, no tools required to change sizes. n ightweight for easy handling, less than six lbs. n Capable of crimping underhood air conditioning applications. n Includes four color-coded die sets for crimping two-braid barrier hose. n Removable die holder accommodates complicated shapes. n Color-coded, urethane encased dies. n Unit can be bench-mounted. n Shipped in a custom carrying case with instructions. n No electrical requirements. n ocator flag centers ferrule in dies. PolarSeal II Hose Pliers The PolarSeal II pliers are used to crimp the clamps on PolarSeal II couplings. The ratcheting pliers will not release until the crimp is complete guaranteeing a proper seal. The straight jaw pliers are used when there are no obstructions to hinder crimping. The notched jaw pliers are for use in tight quarters. Use the side or the front of the pliers to complete the crimp. Vertical Hydraulic Hose Cabinet Rack up sales and get organized at the same time with a new vertical' hydraulic hose cabinet from Gates. Number: n Six narrow and two wide slots to stock a variety of hydraulic hoses. n Designed to support one hydraulic coupling cabinet on top for maximum efficiency. n Optional choice for use as cabinet base with maximum of one fourdrawer cabinet. n Shown with four-drawer cabinet (purchase separately as ). Ratcheting Pliers Number: Straight Jaw Pliers Number: D(2/95) Portable Crimper M A D E I N U S A P A T E N T P E N D I N G Hydraulic Hose Reel Rack This sturdy and convenient rack stores three reels of hose. Number: Dimensions: 30" deep by 28" wide by 72" high (2/95) Notched Jaw Pliers Number: Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 95

97 EQUIPMENT Information Specialized Mining Hose Hydraulic Coupling Cabinet Customized to fit all your needs! Now even more versatile, these easy-to-assemble units are compactly designed to give you years of reliable service. Components are ordered individually by product number for easy customization. 1 2 n MobileCrimp 4-20 Pre-drilled holes in mounting shelf (item #2 below) allows easy mounting of either the Positive Stop or Digital Dial MobileCrimp 4-20 crimper. Safety Hints: If the MobileCrimp 4-20 is mounted on top of the cabinet, you must: Use crimper mounting shelf (item #2 below) Bolt shelf and cabinet to wall using pre-drilled holes Not use the caster leg set n Mounting Shelf for MC 4-20 Crimper Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose n Coupling Cabinet with Four Sliding Shelves (Two Shown) Shelves slide out for easy access and can hold a combination of ten 3-1/2" wide bin boxes or five 7" wide bin boxes. Unit can be stacked and bolted together as shown in illustration. Each measures 41" wide by 21" high by 12" deep. Safety Hint: Slide open only one shelf at a time to avoid tipping. n Stationary egs (Shown) Allows for precise leveling. He avy-duty Caster eg Set (Not Shown) Set consists of four heavy-duty casters, two of which can be locked. n Bin Boxes Order separately in whatever combination best fits your needs. Dividers come with each bin box. Each bin box has slots to allow for maximum utilization. Description Ten 3.5" wide bins with 30 dividers Five 7" wide bins with 15 dividers Three dividers for 3.5" wide bin box Four dividers for 7" wide bin box Two-Drawer Coupling Cabinet This two-drawer cabinet is ideal to add nylon air brake tubing couplings to your hydraulic inventory. This cabinet can be stacked and bolted together with your existing hydraulic cabinet. Uses the same bin boxes as listed above. Measures 41" wide by 11" high by 12" deep. 4 When assembled, the typical combination of two four-shelf coupling cabinets and stationary leg set as shown measures 48" high by 41" wide by 12" deep. 5 Belts Equipment 96 gates.com/mining Gates Corporation

98 FOR SAFETY S SAKE Work Bench Number: Dimensions: 36" wide by 24" deep by 36" tall This new hydraulic work bench is ideal for holding either the Power Crimp 707 or MobileCrimp 4-20 crimpers as well as hydraulic saws. The lower shelf can be used for storage or as shown with the pump. It is made of an angle iron frame construction with a high-density fiberboard top and welded 13-gauge steel lower shelf. All hardware is included to allow for easy assembly in about 10 minutes. Hydraulic Coupling Bin Number: The 24-bin cabinet is constructed of heavy gauge steel. Cabinet measures 34" wide by 24" high by 12" deep. Excellent for storing large 1-1/4" to 2" I.D. couplings. Coupling Bin Boxes Bin boxes for hydraulic couplings. Corrugated cardboard design gives extra strength. Includes four dividers per box. Number: Measures: 5" wide by 4-1/2" high by 11" deep. Number: Measures: 7-1/2" wide by 4-1/2" high by 11" deep. Gates Hose Cutter Model 2-24 For two-wire braid hose through 1-1/2" ID. Number: Clean Easy Cuts Safe Operation FEATURES: n Cuts up to 1-1/2" I.D. two-wire braid reinforced hose. n Designed to operate on standard 20 amp service. n Reversible 8" scalloped-edge, high-speed steel blade with 5/8" bore can be sharpened. n Radius hose feed into blade for safety and reduced friction. n Inner blade guard for safe operation. SPECIFICATIONS Power Source: 1-1/2 HP (2.6 HP Peak), 115V, 60 Hz., 15 Amp motor with power cord and plug. Dimensions: 13" wide by 24" length by 17" high. Weight: 65 lbs. Replacement Blade Number: Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 97

99 EQUIPMENT Belts Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information Gates Power Cutter 208 Number: Effortless Straight Cuts Every Time n Clear face shield for added safety. n Powerful high torque, 4.5 horsepower peak motor that makes cutting faster and easier. n Includes scalloped, 12" blade to dissipate heat, reducing friction for clean, faster cuts up to 1-1/4" I.D. n Optional abrasive blade for continuous use with 1-1/4" I.D and larger spiral-wire reinforced hose. n Safely cuts two and four-wire hoses through 2", six-wire hoses through 1-1/4". n Reversible blade can be sharpened; removal and installation is easy. n Cuts small 3/16" I.D. hose and handles the tough jobs, including 2" I.D. spiral wire hoses.* n Easy to use, front face plate with moveable pins holds hose securely for a clean straight cut. n Sturdy blade guard shields blade for safety. n Permanent mounting brackets (included) to attach saw to table. * Optional abrasive blade preferred for cutting spiral-wire hose, larger than 1-1/4" I.D. CUTTER SPECIFICATIONS Shaft/Arbor Hole Diameter: 1" Power Source: 4.5 HP Peak, 115/50/60 Hz, 20 Amps. No oad Speed: 3,500 rpm Dimensions: 22-1/2" wide by 18-1/4" length by 23-1/2" high Weight: 65 lbs. Gates Hose Cutter Model 6-32 For six-wire spiral and two-wire braid hose through 2" I.D. Number: Clean Easy Cuts Safe Operation FEATURES: n Cuts up to 2" I.D. two-wire braid through six-spiral reinforced hose. n Reversible 10" scalloped-edge, high-speed steel blade with 3/4" bore, can be sharpened. n Radius hose feed into blade for safety and reduced friction. n Inner blade guard for safe operation. n Includes Coolant Spray System Kit for reduced heat in high-capacity cutting applications (recommended for multi-braid and spiral reinforced hose). Kit includes reservoir, spray nozzle and mounting hardware. n Power cord not included. Caution: Keep blade sharp. Heat generated by a dull blade can damage steel and flare the hose. BADE SPECIFICATIONS Blade Dimensions: 12" by 1/8" Scalloped Replacement Number: Optional Abrasive Number: SPECIFICATIONS Power Source: 3 HP (5.2 HP Peak), Single phase, 230V, 60 Hz., 20 Amp motor Dimensions: 22" wide by 42" length by 24" high Weight: 215 lbs. Replacement Blade Number: gates.com/mining Gates Corporation

100 4-16 Portable Hose Saw SPECIFICATIONS Voltage: 120 Volts Cycle: 60 Hz / 1 phase Power: 6.5 Amp No-load speed: 7,400 rpm Wheel size: 6" Arbor Hole: 7/8" FEATURES: n Cuts up to 1", four-wire braid n Abrasive cut-off wheel Number: Hand-Held Hose Cutter Number: Makes clean cuts no ragged edges. Cuts most non-metal reinforced rubber hoses. Excellent for cutting textile-reinforced hose. FEATURES: n ightweight with nylon handles. n Blade closes into handle for safety. n Cutter and blades packaged individually on shrink-wrapped cards. Replacement Blade Number: Small Nylon Tubing Cutter & Replacement Blades Number: Tubing cutter gives straight, clean, square cuts on J844 tubing. FEATURES: n ightweight and compact size 3/4" by 3". n Designed to ensure user's safety. n "Blade guard" offers more protection against accidental blade contact. n Handle has ribs for improved grip. Replacement Blade Number: Gates also offers replacement blades in a five pack bag. Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 99

101 EQUIPMENT Information Swager Conversion Kit for the Power Crimp 707 Produces top quality assemblies using Gates 1/8" and 3/16" thermoplastic hydraulic hose with Gates PCTS couplings and Gates C14 PTFE hose and couplings. Easily converts the Power Crimp 707 to a power swager. Adapter Collar Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Description Number Complete Kit Collar Die Cone Adapter Actuator Rod /2" Spacer Ring Dies and pushers must be ordered separately. See Swage Data Chart in Gates Crimp Data Manual for details. Gates HS-1 Hand Swager Number: Produces top quality assemblies using Gates 1/8" and 3/16" thermoplastic hydraulic hose with Gates PCTS couplings and Gates C14 PTFE hose and couplings. Simply insert the assembly into the swager from the bottom, place dies around the coupling, and pump the handle. A six-ton jack then goes to work and the swage is completed. Positive dies ensure a correct swage every time. Rod Cone Spacer Ring The perfectly swaged assembly is removed and you are ready to repeat the process. Pushers and dies must be ordered separately. SPECIFICATIONS Dimensions: 15" wide by 7" deep by 19-1/2" high Weight: 41 lbs. Belts Equipment Standard Hydraulic Hose 100 gates.com/mining Gates Corporation

102 Hose Assembly Machine Power Mate 25 Portable hose assembly machine for field attachable couplings. Machine Number: (115 volts, 30 amps, 1 phase, 60 cycles.) Folding Stand Number: n Produces complete, dependable hose assemblies. n Applies field attachable couplings in sizes from 3/16" through 2" I.D. on medium and high-pressure hoses. n Accommodates male pipe, swivel, flange and elbow type field attachable couplings. n Easy and safe to operate. n Hand-skiving tool can be used with Power Mate 25. n Affords quick and simple operation reduces costly downtime and delays. n Heavy-duty provides years of trouble-free service. n Weighs 141 lbs. (without stand). Takes up less than 4 by 5 ft. of floor space with stand. n Can be bench mounted or made portable with folding leg stand. Push-On Tool Number: This hand-operated coupling machine, made of rugged cast iron and steel construction, eliminates the hard work of manually pushing stems into hoses. It comes complete with mandrels for 1/4", 3/8", 1/2", 5/8" and 3/4" I.D. sizes of lock-on couplings. Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 101

103 EQUIPMENT Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information Hand-Operated Hose Perforator Tool These hose perforators have needle-studded wooden rollers which perforate the covers of non-skive wire braid hose used in high pressure inert gas applications. They are hand-operated so the operator can control the degree of perforation in the hose cover. 1-1/4" Hose Perforator for 3/16" to 3/4" I.D. Hose Number: Dimensions: 2-1/2" O.D. roller by 1-1/4" wide by 8" OA. Weight: 3/4 lbs. 3" Hose Perforator for 1" to 2" I.D. Hose Number: Dimensions: 3-3/4" O.D. roller by 3" wide by 9-1/2" OA. Weight: 1-1/4 lbs. C14 Hose Cutting Shear Recommended for C14 PTFE Hose Number: This cutting shear handles Gates C14 PTFE hose up through 1" without requiring pretaping of the hose. The shear is fast and easy to use and results in a very clean cut. Weight: 18 lbs. Dimensions: 9" wide by 15" high by 14" deep. 30" handle. xxxxx xx xx xxxx xxxx xxx xx xx Belts Equipment 102 gates.com/mining Gates Corporation

104 C14 Hose Insertion Die Holder for Use with Hose Insertion Dies Required for inserting hose into ferrule on all sizes. Use the fixture (see photo) to mount the Hose Insertion Die Holder onto a bench top to aid in the assembly of Gates C14 hose. Each item listed in the table below must be ordered separately. See product numbers listed in Gates Crimp Data and Dies Manual. Description Number Hose Insertion Die Holder Hose Insertion Fixture C14 Hose Insertion Dies Used to guide the hose into the ferrule when used with the Hose Insertion Die Holder. One set required for each hose size. See product numbers listed in Gates Crimp Data and Dies Manual. C14 Hose Expanders Used to expand the hose and round out the tube after cutting and to insert the stem into the hose. One expander required for each hose size. See product numbers listed in Gates Crimp Data and Dies Manual. C14 Swage Pushers Specially designed to accommodate Gates C14 couplings. They protect the threads and bottom out on the dies to complete the swage. Use the C14 Swage Data Chart in Gates Crimp Data and Dies Manual to determine the proper pushers. C14 Swage Dies Specifically designed to swage Gates C14 hose assemblies. They provide the required swage dimensions to meet full performance. One die set is required for each hose size. See product numbers listed in Gates Crimp Data and Dies Manual. MegaCrimp Number: Coupling Insertion Tool Offers an easy way to confirm the right insertion depth for all Gates wire-braid hydraulic hoses. To use, simply insert the hose into its proper slot indicated by dash size, push it all the way in, check for square cut (maximum allowable angle of cut is five degrees), then mark the insertion depth on the hose. Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 103

105 EQUIPMENT Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories MegaClean System Used to remove dirt from the inside out with the help of pressurized launchers and compatible nozzles. Gates MegaClean foam projectiles sweep through the inside surface of the hose, taking fine particles of loose dirt and other contaminants with them. At percent larger than the hose ID, these projectiles leave nothing behind but a hose that truly is clean from the inside out. MegaClean MC-K32 Kit Number MC-32 Hand auncher (Including "Rotary" Plug & Coupler) MC-GAR-1 Adapter Ring (-4 thru -20) C32 Carrying & Storage Case Hose Nozzles GH-04, GH-05, GH-06, GH-08, GH-10, GH-12, GH-16, GH-20, GH-24, GH-32 JIC Assembly Nozzles GA-04, GA-06, GA-08, GA-10, GA-12, GA-16, GA-20, GA-24, GA-32 GA-04-FFORX Nozzle MC-32 auncher Stand 1 Projectile Catcher Bucket 1 Roll MegaClean Assembly Tape 1 Bag of Projectiles isted in Chart Below MegaClean MC-K20 Kit Number MC-20 Hand auncher Female Quick-Release Coupler C20 Carrying & Storage Case Hose Nozzles GH-04, GH-05, GH-06, GH-08, GH-10, GH-12, GH-16, GH-20 1 Projectile Catcher Bucket 1 Roll MegaClean Assembly Tape 1 Bag of Projectiles isted in Chart Below How it works: Step 1 Standard Hydraulic Hose Equipment Belts MegaClean Projectiles Included in Kits Number Part Number MC-K32 MC-K20 Bag Quantity HAP-04 X X HP-04 X X HAP-06 X X HP-06 X X HAP-08 X X HP-08 X X HP-08-1 X X HP-10 X X HP-12 X X HP-16 X X HP-20 X X HP-24 X HP-32 X 15 Step 2 (continues next page) 104 gates.com/mining Gates Corporation

106 MegaClean Description Number Part Number MegaClean HAP Assembly Projectile (100 ea) MC-HAP-04-1 MegaClean HAP-04 Assembly Projectile (100 ea) MC-HAP-04 MegaClean HP-04 Hose Projectile (100 ea) MC-HP-04 MegaClean HAP-06 Assembly Projectile (100 ea) MC-HAP-06 MegaClean HP-06 Hose Projectile (100 ea) MC-HP-06 MegaClean HAP-08 Assembly Projectile (100 ea) MC-HAP-08 MegaClean HP-08 Hose Projectile (100 ea) MC-HP-08 MegaClean HP-08-1 Hose Projectile (50 ea) MC-HP-08-1 MegaClean HP-10 Hose Projectile (50 ea) MC-HP-10 MegaClean HP-10-1 Hose Projectile (50 ea) MC-HP-10-1 MegaClean HP-12 Hose Projectile (50 ea) MC-HP-12 MegaClean HP-12-1 Hose Projectile (40 ea) MC-HP-12-1 MegaClean HP-14 Hose Projectile (40 ea) MC-HP-14 MegaClean HP-16 Hose Projectile (40 ea) MC-HP-16 MegaClean HP-16-1 Hose Projectile (30 ea) MC-HP-16-1 MegaClean HP-20 Hose Projectile (30 ea) MC-HP-20 MegaClean HP-20-1 Hose Projectile (20 ea) MC-HP-20-1 MegaClean HP-24 Hose Projectile (20 ea) MC-HP-24 MegaClean HP-24-1 Hose Projectile (15 ea) MC-HP-24-1 MegaClean HP-32 Hose Projectile (15 ea) MC-HP-32 MegaClean HP-32-1 Hose Projectile (10 ea) MC-HP-32-1 MegaClean HP-40 Hose Projectile (10 ea) MC-HP-40 MegaClean HP-48 Hose Projectile (10 ea) MC-HP-48 MegaClean HP-56 Hose Projectile (10 ea) MC-HP-56 MegaClean HP-64 Hose Projectile (10 ea) MC-HP-64 Description Bulk Pack System Replacement Projectiles Number Part Number MegaClean HAPB Assembly Projectile Bulk (10000 ea) MC-HAPB-04-1 MegaClean HAPB-04 Assembly Projectile Bulk (10000 ea) MC-HAPB-04 MegaClean HAPB-04 Assembly Projectile Bulk (10000 ea) MC-HPB-04 MegaClean HAPB-06 Assembly Projectile Bulk (10000 ea) MC-HAPB-06 MegaClean HPB-06 Hose Projectile Bulk (10000 ea) MC-HPB-06 MegaClean HAPB-08 Assembly Projectile Bulk (10000 ea) MC-HAPB-08 MegaClean HPB-08 Hose Projectile Bulk (10000 ea) MC-HPB-08 MegaClean HPB-08-1 Hose Projectile Bulk (9000 ea) MC-HPB-08-1 MegaClean HPB-10 Hose Projectile Bulk (7000 ea) MC-HPB-10 MegaClean HPB-10-1 Hose Projectile Bulk (5500 ea) MC-HPB-10-1 MegaClean HPB-12 Hose Projectile Bulk (4000 ea) MC-HPB-12 MegaClean HPB-12-1 Hose Projectile Bulk (3800 ea) MC-HPB-12-1 MegaClean HPB-14 Hose Projectile Bulk (3500 ea) MC-HPB-14 MegaClean HPB-16 Hose Projectile Bulk (2000 ea) MC-HPB-16 MegaClean HPB-16-1 Hose Projectile Bulk (1900 ea) MC-HPB-16-1 MegaClean HPB-20 Hose Projectile Bulk (1500 ea) MC-HPB-20 MegaClean HPB-20-1 Hose Projectile Bulk (1200 ea) MC-HPB-20-1 MegaClean HPB-24 Hose Projectile Bulk (650 ea) MC-HPB-24 MegaClean HPB-24-1 Hose Projectile Bulk (600 ea) MC-HPB-24-1 MegaClean HPB-32 Hose Projectile Bulk (450 ea) MC-HPB-32 MegaClean HPB-32-1 Hose Projectile Bulk (360 ea) MC-HPB-32-1 Step 3 Step 4 Step 5 Step 6 Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 105

107 EQUIPMENT Information MegaClean System Used to remove dirt from the inside out with the help of pressurized launchers and compatible nozzles. Gates MegaClean foam projectiles sweep through the inside surface of the hose, taking fine particles of loose dirt and other contaminants with them. At percent larger than the hose ID, these projectiles leave nothing behind but a hose that truly is clean from the inside out. Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Description Number Part Number MegaClean Starter Kit-K MC-K40-64 MegaClean Starter Kit MC-K32 MegaClean Starter Kit MC-K20 MegaClean Bench Mount Kit MC-BM20 MegaClean -32 Hand auncher MC-32 MegaClean -20 Hand auncher MC-20 MegaClean -64 Hand auncher MC-64 MegaClean Male Quick Release Rotary Plug MC-MQRP MegaClean Female Quick Coupler for auncher MC-FQRC MegaClean C32 (Case Only) MC-C32 MegaClean C64 (Case Only) MC-C64 MegaClean C20 (Case Only) MC-C20 MegaClean Projectile Catcher Bucket MC-PCB MegaClean Assembly Tape MC-TAPE MegaClean auncher Stand 32 & MC-STAND MegaClean Adapter Ring GAR-1 for MC-32 (-2 thru-20) MC-GAR-1 MegaClean Adapter Ring GAR-1 for MC64 (-2 thru-20) MC-GAR-2 MegaClean Adapter Ring GAR-1 for MC64 (-24 and-32) MC-GAR-3 MegaClean GH-04 Hose Nozzle MC-GH-04 MegaClean GH-05 Hose Nozzle MC-GH-05 MegaClean GH-06 Hose Nozzle MC-GH-06 MegaClean GH-08 Hose Nozzle MC-GH-08 MegaClean GH-10 Hose Nozzle MC-GH-10 MegaClean GH-12 Hose Nozzle MC-GH-12 MegaClean GH-16 Hose Nozzle MC-GH-16 MegaClean GH-20 Hose Nozzle MC-GH-20 MegaClean GH-24 Hose Nozzle MC-GH-24 MegaClean GH-32 Hose Nozzle MC-GH-32 MegaClean GH-40 to GH-64 Hose Nozzle Assortment MC-GH MegaClean GT-02 Tube Nozzle MC-GT-02 MegaClean GA-04 JIC Assembly Nozzle MC-GA-04 MegaClean GT-04 Tube Nozzle MC-GT-04 MegaClean GT-05 Tube Nozzle MC-GT-05 MegaClean GA-06 JIC Assembly Nozzle MC-GA-06 MegaClean GT-06 Tube Nozzle MC-GT-06 MegaClean GA-08 Assembly JIC Nozzle or Tube MC-GA-08 MegaClean GA-10 Assembly JIC Nozzle or Tube MC-GA-10 MegaClean GA-12 Assembly JIC Nozzle or Tube MC-GA-12 MegaClean GA-16 Assembly JIC Nozzle or Tube MC-GA-16 MegaClean GT-20 Tube Nozzle MC-GT-20 MegaClean GA-20 Assembly JIC Nozzle or Tube MC-GA-20 MegaClean GA-24 Assembly JIC Nozzle or Tube MC-GA-24 MegaClean GA-32 Assembly JIC Nozzle or Tube MC-GA-32 MegaClean GA-04 FFORX Flat Face Nozzle MC-GA-04-FFORX Belts 106 gates.com/mining Gates Corporation

108 BET PREVENTIVE MAINTENANCE TOOS Preventive Maintenance Tools Proper tension, installation and maintenance can extend belt life and reduce costly downtime. Some of Gates most popular preventive maintenance tools include: A. Sonic Tension Meter, Model 507C For extremely accurate belt tension measuring, the Gates Sonic Tension Meter is an electronic device that measures the natural frequency of a free stationary belt span and instantly computes the static belt tension based upon the belt span length, belt width, and belt type. The Sonic Tension Meter can be used with synchronous and V-belts. Other features include: Output readings can be switched between pounds, kilograms, newtons and hertz. Auto gain control automatically adjusts meter sensitivity. Auto frequency range filters for background noise. Frequency range from 10-5,000 Hz. B. Krikit Gauges For tensioning automotive V-belts up to and including 7/8" top width For tensioning automotive V-ribbed belts up to 8 ribs in width. C. Pencil Type Tension Tester Maximum deflection force: 30 lbs. For use with all small V-belts and synchronous belts. D. Double Barrel Tension Tester Maximum deflection force: 60 lbs. For use with all multiple V-belts and large synchronous belts. E. Five Barrel Tension Tester Maximum deflection force: 165 lbs. For use with all multiple V-belts and large synchronous belts. Sonic Tension Meter and Accessories Description Flat Flexible Sensor Cord Sensor A/C Adapter for 305 Series Inductive Sensor (Magnets Included) Sonic Tension Meter Model 507C Preventive Maintenance Tools Description PM Kit Belt Installation and Maint. Tool Box F. EZ Align Precision aser Alignment Device Red aser Identifies common types of pulley misalignment Green aser Identifies common types of pulley misalignment. A F B C D E G. Truflex and PoweRated Belt ength Finder Measures FHP belts up to 107" to determine equivalent Truflex or PoweRated belt numbers. H. Sheave Gauges and Helps to identify worn sheaves and damaged belts. Tensioning and Alignment Devices Description Truflex and PoweRated Belt ength Finder Sheave Gauge - Metric Sheave Gauge - English Krikit Belt Tension Tester Krikit II Belt Tension Tester b. Double Barrel b. Pencil Type b. Five Barrel EZ Align aser Alignment Device - Red aser EZ Align aser Alignment Device - Green aser G H Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 107

109 POY CHAIN GT CARBON BETS Belts Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information Poly Chain GT Carbon Belts Poly Chain GT Carbon Belts Nothing Tougher. Give yourself a competitive advantage by designing in the Gates Poly Chain GT Carbon drive system instead of roller chain in your next power transmission application. The patented use of Carbon Fiber as the tensile cord in this belt provides increased horsepower rating for greater power density and compactness and increased flexibility, allowing the use of backside idlers. When combined with Gates Poly Chain GT2 sprockets, you have a lightweight, long-lasting, maintenance-free system that's more than a match for roller chain. Markets/Applications All industrial markets, especially suited to replace roller chain drives. Narrow width minimizes reducer overhung loads and left-justified hubs on Poly Chain GT2 sprockets accommodate short shaft lengths. Features/Advantages n Maintenance-free, clean solution for roller chain drive conversion Significantly reduces maintenance costs Equivalent capacity to roller chain drives in the same width Easy rust-free wash-down with Gates Stainless Steel hardware Fast drive conversion payback Quieter than roller chain drives n New construction provides up to 55% more low-speed capacity than the original PCGT construction and 30% more than PCGT2. n Gates curvilinear tooth profile provides high shear strength, noise reduction, and improved load carrying capacity. n Robust carbon tensile cord combines minimal stretch with extraordinary strength and load carrying capacity, while absorbing shock and surge loads. n Durable polyurethane construction resists chemicals, oil, pollutants, and abrasion. n Nylon tooth facing reduces friction and eliminates the need for lubrication. n Fully operational in temperature extremes of -65 F to +185 F (-54 C to +85 C). Recommended Sprockets Poly Chain GT2 Sprockets - 8M and 14M Notes Belt pitch is the distance in millimeters between two adjacent tooth centers as measured on the pitch line of the belt. Belt pitch length is the total length (circumference) in millimeters as measured along the pitch line. The theoretical pitch line of a Poly Chain GT Carbon belt lies within the tensile member.~poly Chain GT Carbon belt part numbers are identical to those of Poly Chain GT2: part number 8MGT denotes an 8mm pitch, 1000mm pitch length and 21mm width.~poly Chain GT Carbon belts can be used on existing drives as replacement for previous generation Poly Chain belts. WARNING: Use of non-gates manufactured sprockets is not recommended: Gates Poly Chain GT2 sprockets are manufactured, specified and tested to fully support the full capabilities of the Poly Chain GT Carbon belt. performance cannot be guaranteed when non-gates sprockets are used. Always utilize Taper-ock type Poly Chain GT2 Sprockets when designing a new Poly Chain GT Carbon belt drive system. Series mm Pitch 12mm Wide Part of Teeth Pitch ength 8MGT MGT MGT MGT MGT MGT MGT Part of Teeth Pitch ength 8MGT MGT MGT MGT MGT MGT MGT gates.com/mining Gates Corporation

110 Poly Chain GT Carbon Belts Series 9274 (continued) 8mm Pitch 12mm Wide (continued) Part of Teeth Pitch ength 8MGT MGT MGT MGT MGT MGT MGT MGT mm Pitch 21mm Wide Part of Teeth Pitch ength 8MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT mm Pitch 36mm Wide Part of Teeth Pitch ength 8MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT mm Pitch 62mm Wide Part of Teeth Pitch ength 8MGT MGT MGT MGT MGT MGT MGT Part of Teeth Pitch ength 8MGT MGT MGT MGT MGT MGT MGT MGT Part of Teeth Pitch ength 8MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT Part of Teeth Pitch ength 8MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT Part of Teeth Pitch ength 8MGT MGT MGT MGT MGT MGT MGT Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 109

111 POY CHAIN GT CARBON BETS Belts Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information Poly Chain GT Carbon Belts Series 9274 (continued) 8mm Pitch 62mm Wide (continued) Part of Teeth Pitch ength 8MGT MGT MGT MGT MGT MGT MGT MGT mm Pitch 20mm Wide Part of Teeth Pitch ength 14MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT mm Pitch 37mm Wide Part of Teeth Pitch ength 14MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT mm Pitch 68mm Wide Part of Teeth Pitch ength 14MGT MGT MGT MGT MGT MGT MGT MGT MGT Part of Teeth Pitch ength 8MGT MGT MGT MGT MGT MGT MGT MGT Part of Teeth Pitch ength 14MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT Part of Teeth Pitch ength 14MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT Part of Teeth Pitch ength 14MGT MGT MGT MGT MGT MGT MGT MGT MGT gates.com/mining Gates Corporation

112 Poly Chain GT Carbon Belts Series 9274 (continued) 14mm Pitch 68mm Wide (continued) Part of Teeth Pitch ength 14MGT MGT MGT MGT MGT mm Pitch 90mm Wide Part of Teeth Pitch ength 14MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT mm Pitch 125mm Wide Part of Teeth Pitch ength 14MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT Part of Teeth Pitch ength 14MGT MGT MGT MGT Part of Teeth Pitch ength 14MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT Part of Teeth Pitch ength 14MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT MGT Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 111

113 Industrial Belt s July, 2010 SUPER HC BETS Information Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose HEAVY DUTY V-BETS Standard Hydraulic Hose Super HC Belts Super HC Belts Pioneered by Gates, these "narrow" cross-sections can transmit up to three times the horsepower of the classical cross-sections (A, B, C, and D) in the same amount of drive space. Markets/Applications Suitable for all industrial applications, particularly where space, weight and horsepower capacity are critical. Features/Advantages n Gates Curves provide proper cord support and full contact with the sheave-groove for uniform loading, uniform wear, and increased belt life. n Flex-Bonded Cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration. n The Flex-Weave Cover is a patented construction for longer cover life, providing extended protection to the core of the belt from oil, dirt, and heat. n Meets RMA oil and heat resistant standards. n Meets RMA static conductivity requirements. Recommended Sheaves Super HC Sheaves Notes Gates Super HC belts are available in 3V, 5V, and 8V cross-sections. Series V Section Size Belt O.C. Qty Per Ctn 3V V V V V V V V V V V V V V V V V V V Size Belt O.C. Qty Per Ctn 3V V V V V V V V V V V V V V V V V V Equipment Belts Series V Section Size Belt O.C. Qty Per Ctn 5V V V Size Belt O.C. Qty Per Ctn 5V V V Gates Corporation gates.com/mining 94 Gates Corporation

114 Super HC Belts Series 9334 (continued) 5V Section (continued) Size Belt O.C. Qty Per Ctn 5V V V V V V V V V V V V V V V V Series V Section Size Belt O.C. Qty Per Ctn 8V V V V V V V V V V V V V V V V Size Belt O.C. Qty Per Ctn 5V V V V V V V V V V V V V V V Size Belt O.C. Qty Per Ctn 8V V V V V V V V V V V V V V V V Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 113

115 SUPER HC BETS Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information Super HC Molded Notch Belts Constructed with Gates proprietary construction, this belt has a superior combination of flex and load carrying capacity, as well as transmitting more horsepower than the classical cross sections in the same amount of drive space. Markets/Applications Suitable for all industrial applications, particularly where space, weight and horsepower capacity are critical. Features/Advantages Notches molded into the belt during manufacturing make this belt well suited for drives with smaller diameter sheaves. Belt Edge is machined for even sheave groove contact resulting in less slip and wear. Flex-Bonded Cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration. Patented EPDM Material construction provides -60 F to +250 F temperature range to resist belt cracking. Meets RMA oil and heat resistant standards. Meets RMA static conductivity requirements. Recommended Sheaves Super HC Sheaves Notes: Gates Super HC Molded Notch belts are available in 3VX and 5VX cross-sections. Series VX Section Size Belt O.C. Qty Per Ctn 3VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX Size Belt O.C. Qty Per Ctn 3VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX Belts 114 gates.com/mining Gates Corporation

116 Super HC Molded Notch Belts Series VX Section Size Belt O.C. Qty Per Ctn 5VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX Size Belt O.C. Qty Per Ctn 5VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX VX Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 115

117 SUPER HC BETS Super HC Molded Notch Belts Series VX Section Size Belt O.C. Qty Per Ctn 8VX VX VX VX VX VX VX Size 53/64 Belt O.C. Qty Per Ctn 8VX VX VX VX VX VX Belts Equipment Standard Hydraulic Hose Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories 116 gates.com/mining Gates Corporation

118 PREDATOR BETS Predator Single Belts Specifically designed for aggressive applications, this extra heavy-duty belt construction provides extraordinary high impact strength, capacity, and wear resistance. Markets/Applications Predator belts are well suited as replacement belts for applications exposed to pulsating loads or heavy shock loads, such as mining, agriculture, wood processing, oil field equipment, heavy construction and sand/gravel operations. Features/Advantages n Aramid Tensile Cords combine limited stretch with extraordinary strength and durability that is pound-for-pound stronger than steel. n Bareback Cover resists debris and allows the belt to slip under extreme shock load conditions, reducing heat buildup and prolonging belt life. n Gates Curves provide proper cord support and full contact with the sheave-groove for equal loading, uniform wear, and increased belt life. n Meets RMA oil and heat resistant standards. Notes Predator belts do not meet RMA requirements for belt static conductivity. When application requires Predator belt sets, request belts with same group/match number. Series 9185 AP Section Part Belt O.C. AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP Series 9186 BP Section Part Belt O.C. BP BP BP BP BP Part Belt O.C. AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP Part Belt O.C. BP BP BP BP BP Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 117

119 PREDATOR BETS Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Predator Single Belts Series 9186 (continued) BP Section (continued) Part Belt O.C. BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP Series 9187 CP Section Part Belt O.C. CP CP CP CP CP CP CP CP CP Part Belt O.C. BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP Part Belt O.C. CP CP CP CP CP CP CP CP Standard Hydraulic Hose Series VP Section Part Belt O.C. 5VP VP VP VP VP VP VP VP VP VP VP VP VP VP Part Belt O.C. 5VP VP VP VP VP VP VP VP VP VP VP VP VP Belts Equipment 118 gates.com/mining Gates Corporation

120 Predator Single Belts Series VP Section Part Belt O.C. 8VP VP VP VP VP VP VP VP Series 9190 SPBP Section Part Pitch ength (mm) SPB1260P SPB1500P SPB1600P SPB1700P SPB1800P SPB1900P SPB2000P SPB2120P SPB2240P SPB2360P SPB2500P SPB2650P SPB2800P SPB3000P SPB3150P SPB3350P Part Belt O.C. 8VP VP VP VP VP VP VP Part Pitch ength (mm) SPB3550P SPB3750P SPB4000P SPB4250P SPB4500P SPB4750P SPB5000P SPB5300P SPB5600P SPB6000P SPB6300P SPB6700P SPB7100P SPB7500P SPB8000P Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 119

121 PREDATOR BETS Predator Single Belts Series 9191 SPCP Section Part Pitch ength (mm) SPC2000P SPC2120P SPC2240P SPC2360P SPC2500P SPC2650P SPC2800P SPC3000P SPC3150P SPC3350P SPC3550P SPC3750P SPC4000P SPC4250P Part Pitch ength (mm) SPC4500P SPC4750P SPC5000P SPC5300P SPC5600P SPC6000P SPC6300P SPC6700P SPC7100P SPC7500P SPC8000P SPC8500P SPC9000P Belts Equipment Standard Hydraulic Hose Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories 120 gates.com/mining Gates Corporation

122 Industrial Belt s July, 2010 HEAVY DUTY V-BETS Predator PowerBand Belts Belts Specifically designed for aggressive applications, this extra heavy-duty belt construction provides extraordinary high impact strength, capacity, and wear resistance. Markets/Applications Predator belts are well suited as replacement belts for applications exposed to pulsating loads or heavy shock loads, such as mining, agriculture, wood processing, oil field equipment, heavy construction and sand/gravel operations. Features/Advantages Aramid Tensile Cords combine limited stretch with extraordinary strength and durability that is pound-for-pound stronger than steel. Bareback Cover resists debris and allows the belt to slip under extreme shock load conditions, reducing heat buildup and prolonging belt life. Multiple layer Tie Band provides excellent lateral rigidity to prevent belts from turning over or from coming off of the drive. Gates Curves provide proper cord support and full contact with the sheave-groove for equal loading, uniform wear, and increased belt life. Meets RMA oil and heat resistant standards. Size Range/Availability arge Inventory of standard lengths and widths are readily available. See sizing table for details. Belt Slitters located onsite at several Gates Service Centers can cut down an existing belt in inventory to the strand width needed. Made-To-Order Belt engths are available in any size from: CP (80 to 400 inch), 3VP (45 to 220 inch), 5VP (50 to 660 inch) and 8VP (100 to 660 inch). Check with Customer Service for minimum order quantity and manufacturing lead time. Recommended Sheaves Super HC Sheaves as recommended by DesignFlex Pro drive analysis. Notes When application requires Predator PowerBand belt sets, request same group/match number. Predator belts do not meet RMA requirements for belt static conductivity. Belt part number is constructed by placing the (#) number of strands required followed byaslash (/) in front of the belt size. For Example, 5/3VP800 represents a 3VP800 with 5 joined strands. Belt product number is 8 or 9 digits constructed of product series prefix, number of strands, and belt length. For example, represents a"3vp" section PowerBand (9180) with 5 strands (5) that is 80.0 inches (080) long. Series 9184 CP Section Size Belt O.C. 3/CP /CP /CP /CP /CP Size Belt O.C. 4/CP /CP /CP /CP /CP CP Predator belts are available up to 12 strands. Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining Gates Corporation

123 PREDATOR BETS Belts Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information Predator PowerBand Belts Series VP Section Size (# = strands) Belt O.C. Per Belt Width In Number of s #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP #/3VP Series VP Section Size (# = strands) Belt O.C. Per Belt Width In Number of s 13 to Maximum (## = strands) #/5VP ##060 #/5VP ##063 #/5VP ##067 #/5VP ##071 #/5VP ##075 #/5VP ##080 #/5VP ##085 #/5VP ##087 #/5VP ##090 #/5VP ##095 #/5VP ##100 #/5VP ##106 #/5VP ##112 #/5VP ##118 #/5VP ##125 #/5VP ##132 #/5VP ##140 #/5VP ##150 #/5VP ##160 #/5VP ##170 #/5VP ##180 #/5VP ##190 #/5VP ##200 #/5VP ##203 #/5VP ##212 #/5VP ##224 #/5VP ##236 #/5VP ##250 #/5VP ##265 #/5VP ##280 #/5VP ##300 #/5VP ##315 #/5VP ##335 #/5VP ## gates.com/mining Gates Corporation

124 Predator PowerBand Belts Series VP Section Size (# = strands) Belt O.C. Per Belt Width In Number of s #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP #/8VP Information Specialized Mining Hose Specialized Mining Couplings, Adapters and Accessories Standard Hydraulic Hose Equipment Belts Powering Progress. gates.com/mining 123

125 HI-POWER II BETS Belts Equipment Standard Hydraulic Hose Specialized Mining Couplings, Adapters and Accessories Specialized Mining Hose Information Hi-Power II Belts Featuring a composite, multi-purpose construction, these belts resist oil and heat, ozone, sunlight, weather, and aging. Markets/Applications Suitable for all industrial applications, including v-flat drives. Features/Advantages n Gates Curves provide proper cord support and full contact with the sheave-groove for uniform loading, uniform wear, and increased belt life. n Flex-Bonded Cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration. n The Flex-Weave Cover is a patented fabric construction for longer cover life, providing extended protection to the belt core from oil, dirt and heat. n Meets RMA oil and heat resistant standards. n Meets RMA static conductivity requirements. Recommended Sheaves Multi-Duty Sheaves Notes Gates Hi-Power belts are available in A, B, C, D and E cross sections. Series 9002 A Section Size Belt O.C. Qty Per Ctn A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A Size Belt O.C. Qty Per Ctn A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A gates.com/mining Gates Corporation