SmartCom 3. Cabinet Heaters. Heat Exchanger models. Cabinet Heaters. VN/VD Vertical Heaters. HN/HD Horizontal Heaters. RN/RD Downflow Heaters

Transcription

1 Smartom 3 abinet eaters eat Exchanger models VR as and xial Oil an ired abinet eaters VN/V Vertical eaters N/ orizontal eaters RN/R ownflow eaters

2 abinet eaters Introduction The enson range of cabinet heaters combines innovative design with a proven four pass heat exchanger technology to provide a high effi ciency cost effective and durable range. The units may be specifi ed for either free blowing applications or for use with ductwork. Units are manufactured in accordance with ISO 1 accreditation, all heater effi ciencies are compliant with Part L2 of the 2010 uilding Regulations with the majority of models also meeting the higher effi ciency requirements for Enhanced apital llowances. Options igh low or fully modulating burners ombustion air adaptors Stainless steel tubular heat exchanger ir inlet spigots ir inlet fi lters Manual or motorised inlet dampers Up rated fan motor for increased static pressure pplications actories Warehouses Workshops Showrooms reenhouses Model Range abinet heaters are available as either gas or oil fi red models. as fi red cabinet heaters are suitable for use with Natural as (20), most units can also be specifi ed for Propane (31) Oil fi red cabinet heaters are suitable for use with lass gas oil (35 sec), most units can also be specifi ed for erosene (28 sec oil) Vertical freestanding models are available from 32kW to 380kW orizontal and own fl ow models from 58kW to 380kW E This symbol verifi es that the product has been independently assessed and currently qualifi es for the E scheme, an upfront tax relief enabling businesses that invest in energy-saving equipment to claim 100% fi rst-year capital allowances against their taxable profi ts.

3 Specification abinets abinets are constructed from electro-zinc coated steel with an inner heat shield skin and an epoxy powder coat fi nish outer skin to form a rigid and durable casework. ir istribution entrifugal fan(s) circulate large air volumes evenly across the full heat exchanger surface for enhanced life expectancy. ans on models 30 to 85 are direct drive with a single phase motor. Larger models have belt drive fans and three phase motors compliant with directive 2005/32/E. ree blowing heaters are fi tted with long throw discharge nozzles complete with horizontal louvres. Nozzles can be rotated through 360 o. Models are supplied with a raised rear nozzle (one per three nozzle heater and two per four nozzle heater). eaters for use with ductwork are supplied with a duct outlet spigot. eat Exchanger and urner our pass combustion chamber/heat exchanger assembly provides improved thermal effi ciency with extended life expectancy. stainless steel chamber is combined with a high effi ciency tubular heat exchanger to achieve thermal effi ciency in excess of 91% The complete assembly is mounted to allow for thermal expansion thereby avoiding undue thermal stress and premature heat exchanger failure. as fi red units are fi tted with a fully automatic forced draught burner complete with full safety controls to EN676 and the heaters are E certifi ed. Oil fi red units are supplied complete with a fully automatic burner complete with safety controls and factory fi tted fi re valve and oil fi lter. n additional external fi re valve may be required in accordance with S 510:Part2:1978. ontrols combined fan and limit switch is fi tted on all heaters. In the event of overheating the unit would automatically be shut down by the limit thermostat. ll heaters are supplied with an electronic programmer complete with optimised control, this is factory fi tted and wired on free-blowing vertical models. or horizontal, and all duct outlet models down fl ow heaters the controller is supplied loose for on site wiring by the installer. TENIL T New Model Ref Old Model Ref as ired E pproved* Nominal heat output Temperature rise as onsumption Nat gas 20 as onsumption propane 31 Minimum inlet pressure Nat gas 20 Minimum inlet pressure propane 31 as onnection kw m 3 /h m 3 /h mbar mbar Rc ¾ ¾ ¼ ¼ ¼ Oil ired E pproved* Nominal heat output Temperature rise Oil onsumption Oil onnection ir andling ata irflow Throw 1 (N Type) Static pressure ( Type) Std motor Increased motor Main fan motor L 230/1/50 L 15/3/50 Up-rated fan motor L 13/3/50 eneral ata lue diameter Nominal ombustion air diameter Nominal Noise level 3 Net weight kw l/h Rc m 3 /s m Pa Pa kw amp amp kw amp mmø mmø d() kg Throw is dependent on building height, room temperature and nozzle settings. 3 Noise levels measured at 5 metres from appliance. 2 as lines must be adequately sized and reduced at appliance as required. *Please check ETL at time of ordering for latest listings as criteria are subject to change

4 abinet eaters Vertical eaters VN/V Eø L ront View Side View IMENSIONS New Model Ref Old Model Ref E mmø Oil as Standard Extended L eaters with 3 or nozzles are supplied with extended head on the rear nozzle(s). or applications with restricted headroom, units may be specifi ed with all nozzles at standard height

5 ir ischarge and Inlet etails VN/V Nozzle outlet Nozzle outlet Nozzle outlet uct outlet spigot Return ir spigots and ilters VN/V Side inlet spigot left (as shown) or right - please specify at time of order Rear inlet spigot Side inlet fi lter Left (as shown) or right - please specify at time of order. dditional side inlet spigot is required to connect fi lter box to inlet ductwork IMENSIONS New Model Ref Old Model Ref ead plan (VN) Nozzle detail (VN) Outlet Spigot (V) Side Inlet Spigot (VN/V) Rear Inlet Spigot (VN/V) Inlet ilter ssembly (VN/V) Installation learances ront Side Rear no. Spigot ø E ilter cassettes can be withdrawn from either side, ensure adequate clearance for withdrawal i.e. full width of fi lter box

6 abinet eaters orizontal eaters N/ L Eø M N 5 5 P 92 R S Q Side View End View Note: Units may be specifi ed for airfl ow right to left which is the standard confi guration as shown. lternatively units can be specifi ed for airfl ow left to right. Plan View IMENSIONS New Model Ref Old Model Ref E mmø Oil as L mmø M N P Q R S

7 ownflow eaters RN/R 5 N M 5 P Eø L ront View Side View IMENSIONS New Model Ref Old Model Ref E mmø Oil as L M N P

8 ir ischarge and Inlet etails ischarge outlets (N/RN) (ll N/RN models are supplied with louvred outlets) Outlet spigot (/R) (lue location shown for standard R-L horizontal airfl ow) End inlet spigot (N/RN /R) (urner location shown for standard R-L horizontal airfl ow) lternative Return ir Spigots E E Top or bottom inlet spigot N/ Rear inlet spigot N/ Side inlet spigot RN/R Rear inlet spigot RN/R ir ilters Top or bottom inlet fi lter N/ Side inlet fi lter RN/R IMENSIONS New Model Ref Old Model Ref Nozzle ø (N/RN) uct Spigot (ll) Top & Side Inlet (N/ & RN/R) Rear Inlet (N/) Installation learances ront Top (RN/R) Top 1 (N/) Rear E Top clearance applies to units with side air inlet. or units with top air inlet allow mm /EN/009/0111 enson eating, Ludlow Road nighton, Powys, L7 1LP United ingdom Telephone acsimile sales@bensonheating.co.uk Website enson eating Ltd is a registered trademark of mbirad Limited. ecause of continuous product innovation, enson eating reserves the right to change product specifi cation without due notice.