Migmaster 250 Pro. Spare parts list. Ordering number. Validforserialno.528,607-xxx-xxxx

Transcription

1 Spare parts list Validforserialno.528,607-xxx-xxxx Ordering number Migmaster 250 Pro 208/230V, 1 50/60Hz Migmaster 250 Pro 208/230/460/575V, 1 50/60Hz Spare parts are to be ordered through the nearest ESAB agency. Kindly indicate type of unit, serial number, denominations and ordering numbers according to the spare parts list. Maintenance and repair work should be performed by an experienced person, and electrical work only by a trained electrician. Use only recommended spare parts. Rights reserved to alter specifications without notice

2 Item Qty M250 Qty M250 mv C = component designation in the circuit diagram Ordering no. Denomination Notes C Rubber mat Cover Rubber mat Side panel with text Right Shelf Holder Clamp Shaft Washer Ø Wheel Ø Locking washer Ø Link wheel Ø Switch QF Switch Switch 7 step SA Switch 3 step SA Signal lamp Orange V Signal lamp HL OKC plate Side panel Feeder mechanism Receptacle Mains cable Mains cable M V/230V, 1 50/60Hz M250mv - 208/230/460/575V, 1 50/60Hz - 2 -

3 Migmaster 250 Pro Migmaster 250 Pro(mv) - 3 -

4 Item Qty M250 Qty M250 mv C = component designation in the circuit diagram Ordering no. Denomination Notes C Left corner Handle Upper front panel Right corner Lower front plate with text Lowerfrontplatewithtext Grill M V/230V, 1 50/60Hz M250mv - 208/230/460/575V, 1 50/60Hz - 4 -

5 - 5 -

6 C = component designation in the circuit diagram Item Qty Ordering no. Denomination Notes C Glass Seal Panel Protection frame Plate Circuit-board AP Spacer Potentiometer RP Knob Spot welding KIT MMC module Contains items

7 - 7 -

8 C = component designation in the circuit diagram Item Qty Ordering no. Denomination Notes C Rear panel Bushing Cable inlet Securing chain - 8 -

9 - 9 -

10 Item Qty M250 Qty M250 mv C = component designation in the circuit diagram Ordering no. Denomination Notes C Intermediate plate 502 1/ Terminal Cover Brake hub Support Circuit board AP Circuit board Intermediate plate Resistor Transformer TC Transformer Bracket Contactor KM Control transformer Auxiliary contact Gas valve YV Terminal block M V/230V, 1 50/60Hz M250mv - 208/230/460/575V, 1 50/60Hz

11 Migmaster 250 Pro Migmaster 250 Pro(mv)

12 Item Qty M250 Qty M250 mv C = component designation in the circuit diagram Ordering no. Denomination Notes C Transformer TM Thermal switch Transformer TM Inductor L Inductor L Thermal switch Rail Current terminal Plate Capacitor C Diode bridge V1-V Bottom plate Bracket Fan TM Bracket L Cover R Cable V1-V Capacitor Shunt Gland with lock M V/230V, 1 50/60Hz M250mv - 208/230/460/575V, 1 50/60Hz

13 - 13 -

14 (A) = accessory C = component designation in the circuit diagram Item Qty Ordering no. Denomination Notes C Wire feed mechanism Complete, contains items Pressure arm Complete, contains items Spacer sleeve Pressure roller Pressure roller Knurled Nut SGA D Holder Shaft Spring Drive unit M Drive unit M Locking washer Included in item Key Included in item Inlet nozzle Pin bolt Pressure transducer Insulating sleeve 715a Insert tube Plastic, must be used together with item 716a. For welding with Al wire. 715b Insert tube Steel, must be used together with item 716b. 716a Outlet nozzle Must be used together with item 715a. For welding with Al wire. 716b Outlet nozzle Must be used together with item 715b Current sleeve Spacer sleeve Ø 16/8.2x Washer Ø 16/8.4x Screw M8x Protection plate O-ring Screw M5x Screw M4x Feedroller Ø mmFe,Ss,coredwire Feedroller Ø mmFe,Ss,coredwire Feedroller Ø mmFe,Ss,coredwire Feedroller Ø mmAlwire Shaft Gear housing Screw M6x16 s2mpro

15 s2mpro

16 Wear components (W.F.Mechanism ) Item Denomination Ordering no. Notes A Pressure roller B Feed roller Ø /.035 ( /0.9mm) Fe, Ss, cored wire. Ø.030/ /.045 (0.8/ /1.1mm) Fe, Ss, cored wire. Ø.035/ /64 (0.9/ mm) Al wire. C Inlet nozzle D Insert tube E Outlet nozzle Plastic,mustbeusedtogetherwithitem , for welding with Al wire. Steel,mustbeusedtogetherwithitem Mustbeusedtogetherwithitem , for welding with Al wire. Mustbeusedtogetherwithitem Welding with aluminium wires. In order to weld with aluminium wires, proper rollers, nozzles and liners for aluminiumwiresmustbeused.itisrecommendedtouse3mlongweldinggunfor aluminium wires, equipped with appropriate wear parts. wmpro