Height extensions. Basic Operating Instructions. Number of boxes in lot

Transcription

1 Height extensions Basic Operating Instructions Number of boxes in lot

2 INFORMATION YOU MUST TAKE HEED OF THE GATE UNITS THAT THE HEIGHT EXTENSIONS FIT TO ARE STANDARD 2.3 (SINGLE) OR 4.6 DOUBLE GATES. THE HEIGHT EXTENSIONS CANNOT BE USED WITH THE WIDTH EXTENSIONS WHAT YOUR DELIVERY CONTAINS AND WHERE TO LOOK FOR WHAT The package contains 4 lengths of 10mm carbon fibre rod partially assembled with 25mm x 4 mm flat carbon fibre diagonal struts. The struts are colour coded as follows:- Yellow = Left Hand Gate Upper Extension Red Blue = Left Hand Gate Lower Extension = Right Hand Gate Upper Extension Green = Right Hand Gate Lower Extension NOTE: LEFT HAND GATE CLOSES TO THE LEFT AS YOU ARE FACING THE CABINET DOOR, RIGHT HAND CLOSES TO THE RIGHT AS YOU FACE THE CABINET DOOR. 1

3 The box also contains four vertical struts which are colour coded as follows:- Yellow = Left Hand Gate D Plate Upper Extension Assembly Red = Left Hand Gate Lower Extension Assembly + fittings Blue = Right Hand Gate D Plate Upper Extension Assembly Green = Right Hand Gate Lower Extension Assembly + fittings FITTING INSTRUCTIONS HEIGHT EXTENSIONS TO NEW GATES What you will need: 4mm and 3mm Allen Keys, 10mm and 8mm spanners. Unpack the polythene package and identify the four colour coded 10mm carbon fibre pole assemblies and the four colour coded vertical hangers. The gates should in the CLOSED POSITION and SWITCHED OFF during the fitting procedure. Gates fitted with an energiser will be live in the closed position while switched on. The parts are supplied with a coloured identification dot which corresponds to a similar coloured dot on the gate itself. The basic rule is to assemble dot to dot - yellow to yellow and face to face, blue to blue etc. 2

4 1. Remove 2 x M5 Nylock nuts and 2 x penny washers from Left Hand Gate D Plate (Yellow). Fit the Yellow coded carbon fibre strut (Yellow Dots FACING each other it will only fit in that orientation). Replace penny washers and tighten M5 nylock nuts. Loosen the M5 Cap Head screw and nylock nut securing the short aluminium clamp to allow later fitting of 10mm dia carbon fibre. 2. Repeat as above (1) for the Right Hand Gate (Blue coded strut) 3

5 3. Identify the M6 stud with the yellow dot on the centre pivot. 4. Select the 10mm dia carbon fibre extension with the yellow coded dot. Cut through the tie-wrap securing 2 x penny washers and 1 x M6 nylock fixings. Fit the assembly to the stud in sequence penny washer, assembly (Yellow dots facing) - penny washer, M6 nylock. Tighten loosely. 4

6 Trap the 10mm dia carbon fibre between the carbon fibre D Plate strut and the aluminium clamp and tighten loosely the M5 cap head screw to allow final adjustment at a later stage. 5. Repeat as above (4) for the Right Hand Gate (Blue coded). 5

7 6. Identify the Left Hand Gate Lower extension strut and remove the nylock nut from the plastic clamp adjacent to the red dot. Position the clamp on the top outer bar, replace nut and tighten loosely. 6

8 Measure 60cm from the end of the centre pivot guard to the edge of the plastic clamp and tighten in position. Loosen the middle clamp on the strut and tighten loosely over the lower 16mm dia bar. 7. Loosen the lower aluminium clamp ready to fit the 10mm dia c/f. 8. Identify the Right Hand Gate Lower Extension Assembly (Green) and repeat as above stages (6) and (7). 7

9 9. Select the 10mm dia carbon fibre extension with the RED coded dot. Cut through the tie-wrap securing 2 x penny washers and 1 x M6 nylock fixings. Fit the assembly to the stud in sequence penny washer, assembly (Yellow dots facing) - penny washer, M6 nylock. Tighten loosely. 8

10 10. Trap the 10mm dia carbon fibre between the carbon fibre Lower Extension strut and the aluminium clamp and tighten loosely the M5 cap head screw to allow final adjustment at a later stage. 11. Repeat stages (9) and (10) for the right hand gate assembly (Green). 9

11 12. All fittings are now attached to the gate allowing final adjustments to be made to ensure the gate is symmetrical. 10

12 SAFETY INFORMATION General Warnings and Precautions Do not remove the plastic covers from the gate arm unless the gate is turned off Do not remove the gate from the gate holder unless the gate has been turned off. Do not remove or change the battery unless the gate has been turned off. Do not connect the battery to a mains charger while the battery is connected to the gate If horses are to pass through the gate such that the gate is opened in front of the horse then the horse should be kept back from but in view of the gate the first time it comes across the gate. Once introduced the horse will treat the gate as any other everyday object. Environmental conditions that may affect use Temperature The accessory is suitable for temperatures in the range of -15 deg C to 40 deg C. Rainfall wet weather will not have an effect on the part Wind with the extensions fitted the gate may move around a bit more in high winds but will continue to operate normally Sunshine All exterior components are UV stabilised or unaffected by sunshine. 11

13 Assistance Information Sales Call on Service Call on E Mail jim@dofygate.co.uk Skype jim.alston2 Mobile Numbers Office For operational information including tuning in fobs or pairing gates then please try our web page There is also other information you may find useful in this section of the website. For sales and accessories please contact Anglia Farmers on or use our website Dofygate Ltd is located at Manor Farm, Calthorpe, Norwich. NR11 7QR Other Accessories Extra fob Can be tuned in to any gate Extra post fixing allows the gate to be relocated easily Extra adjustable fixing allows the gate to be lined up every time Energiser for stockk control Height extension necessary to contain some groupos of animals Battery 7.0 amp hour lead acid AGM Gel battery Charger 700ma Automatic closing uses 2 infra red sensors to safely close the gate automatically following an open command from a fob or other device Call 2 Open Must be used with auto close Keypad Must be used with auto close Security Plate can be clamped under the adjustable bracket to prevent unauthorised removal of the gate 12

14 Timed open/close must be used with auto close Flashing warning LED light cabinet mounted and warns of impending closure Warning horn reversing type intermittent horn sounds when gate is up and warns of impending closure. 13