AgriWheel Single Gate Kit Low Voltage & Solar. Installation & Operating Instructions

Size: px
Start display at page:

Download "AgriWheel Single Gate Kit Low Voltage & Solar. Installation & Operating Instructions"

Transcription

1 AgriWheel Single Gate Kit Low Voltage & Solar Installation & Operating Instructions

2 Thank you for purchasing you AgriWheel system. Please remove the lids from both the machine and control box and remove all the loose contents which have been stored in there for transit only. Please check you have all the following parts to make up the basic system. There may be additional parts which relate to your own personal order. List of parts AgriWheel Machine With Lid Control Box E-Lock with key(s) 1 x Safety Beams 2 x Remote Control Key-Fobs Flexible Conduit Kit Instruction Manual Once you have checked you have all the parts required, please find below a list of tools required to install a basic AgriWheel system. List of Tools Required 4mm Allen Key Two 17mm Spanners 10.2mm Drill Two 10mm Spanners Length of String (longer than gate) Screwdriver & Screws 16mm Drill or Cone cutter Small Philips Screwdriver Small Flat End Screwdriver Wire Strippers Voltmeter

3 Mounting Your AgriWheel 175mm 75mm Remove the 2 M10 x 100 bolts and plate from the suspension arms. Drill 2 x 10mm clearance holes as per diagram, on the bottom of the upright on the latch end of the gate. Locate the bolts through the plate, and through the drilled holes, and re-mount the machine assembly and tighten the assembly together making sure the plate/bracket remain vertical. Setting the Tracking of Your AgriWheel Tie a length of string, onto the hinge pin and hook the string under the hinge end of the gate and pull it the length of the gate and under the wheel. Your Agriwheel has come with the locking bolts loose, angle the machine so the string runs through the centre line of the machine, and emerges through the centre of the wheel at 90 degrees, tighten the 2 M10 x 20 bolts into the pivot block, and the M6 locking nuts & bolts. Correct alignment reduces tyre wear and amp draw (battery life) as well as improves the speed & performance of the gate. Page 3

4 Fitting the E-Lock Bolt the E-lock to the gate at the desired height making sure there is enough clearance for it not to foul on the keep when the gate is closing. Recommended height is about 300mm (1ft) above the Agriwheel lid Lock the keep into the lock and push it tight to the post. Align the keep centrally to the lock so there is equal clearance all round. Mark the position of the keep on the post to enable you to secure it in place. YOU NEED TO WIRE IN THE LOCK BOARD Lock Board Wiring Chart *Place a dab of petroleum jelly on the terminal connections to prevent corrosion WHITE wire to Control Board Flash Lamp + terminal BLACK Wire to Battery Negative (-) Terminal Red Wire to Battery Positive (+) Terminal BLACK Wire From Lock RED Wire From Lock Page 4

5 Beginning The Wiring To begin the wiring you will need one length of 2-core 1.5mm cable (you will need to measure from the E-Lock, down and along the gate and into the control box) and one length of 2-core 2.5mm cable ( measured from the machine to the control box) do not leave the cable shortalways place the machine on the lowest point of the drive surface, to make sure the cable doesn t pull tight when the gate is working. Place both cables through the 100mm length of flexible conduit supplied. Then place the 2-core x 2.5mm cable through the 400mm length, and the 2-core x 1.5mm through the 1200mm length & clip together as per diagram above using the T-clip supplied. The 2.5mm cable must then pass through the back of the machine and clip the 400mm conduit into the end piece installed. We would reccomed a small junction box to join the E-Lock cable to your cable, or alternatively feed your cable into the back of the lock and connect it direct to the internal connection block The latch should then be wired up as per diagram on previous page. The polarity is not important. However the motor should be connected in the machine using connector blocks. When first powering the gate the gate should open, if it dosent swap the polarity of the motor cables WHITE wire to Control Board Flash Lamp + terminal The cable should then be run the length of the gate, to the control box, allowing for the gate to open & close without stretching or trapping the cable. The flexible conduit & clips are available separately. The flexible conduit also fits inside 20mm conduit readily available at most diy outlets. Page 5

6 The Control Box Your Control Box needs to be mounted securely near the hinge post. The wiring from the gate needs to be slack enough to allow the wiring not to be stretched when the gate is closed, but being careful the wiring doesn t get trapped during the operation of the gate. Where possible, enter the box with the cable, preferably from the underneath. This avoids any water/snow laying on the top seeping in. If required, flexible conduit & fixings can be purchased separately from our website, or from most DIY outlets. The contents & layout of your box will vary depending on your particular order. You will need to mount the box with good strong fixings, bearing in mind the weight of the box once the battery (s) are all replaced. At this point, before you mount the box you need to plan ahead. The beams need to be mounted approx 550mm from the ground. You will have to run a cable underground for the beam on the other post, and you may have cables to lay to an intercom or digital keypad. Now is the time to plan where all these cables are going to run up the post and into the box. Exit Keypad Re-Open Beams Intercom Page 6

7 Charging the System There are two ways you can charge the system, Solar or Mains, however by this point you will already have decided how you are going to charge the system, both methods are connected into the system in the same way. Charging with Solar You will have to decide the best site for your solar panel, it needs to be facing due south, and ideally not to be in the shadow of any trees or buildings. (If your not sure, it is an idea to go out and stand there 3 or 4 times in a day to assess your site. Once you have decided a position you will have to mount onto a post, some people mount it low & fenced in (as pictured), and some people prefer to put it out of peoples reach. (You will need to fabricate your own support. Charging with Mains Your AgriWheel will come with an AC-DC transformer which must be connected as shown below. This must simply be connected straight into the control board, You may need to extend the cable with a suitable connector. WARNING! Although at this point you are dealing with DC Low Voltage current, if any changes to the mains supply are required we recommend you contact a qualified electrician. Before you connect either the transformer or solar panel up, you must connect up at the control board end first, this avoid any live voltage coming through the cable when you are making the connections. With the transformer connect into terminals SOLAR + -, OBSERVE CORRECT POLARITY INCORRECT CONNECTION WILL CAUSE SEVERE DAMAGE Once mounted, you need to connect the panel, with the use of a simple voltmeter, you will need to determine which is the positive and negative terminals (place your meter on the connector strips arrowed right). Once you have established this, connect the cables by pushing in the connector button and inserting the cable securely.

8 Cable connections Before you begin to connect & set up the machine, you will need to install a mechanical stop to prevent the gate travelling back too far. As pictured left, a slab and gravel run helps to prevent slip in wet conditions FULL CONTROL BOARD INSTRUCTIONS ON LATER PAGES Once the above connections are made follow the instructions on the following pages to set up your control board Page 7

9 External Antenna Exit Wand Transformer AC Only DO NOT USE Solar panel or DC Transformer DC12V Motor Push button Flash lamp & DC12v Power supply for solar function of photocells DC12V Battery Photocell (NO Signal) Connect to C & NC on photocell 1.) The control board uses a built in current feedback as limits, when it contacts stop block, it will stop working automatically. 2.) When the gates are closing if they run into obstacle they will stop and auto reverse.

10 Connect gate motor to MOTOR Terminal If the directions of motor running is reversed, Exchange two wires on motor terminals. Gate should open on first command Transformer can be used to supply power if you don't use solar panel and battery. Output voltage of transformer is AC12v rated power must be W. AC12V terminals are for transformer only AC12V WARNING CONNECT DC TRANSFORMER TO SOLAR PANEL INPUT The control board has built-in solar regulator, once the batteries are fully charged, it will stop charging automatically. Output Voltage and power of Solar panel must be 18v 10w to 18v 100w Pay close attention to POSITIVE(+) and NEGATIVE(-) Terminals. If the wires are connected incorrectly the control board will be damaged Connecting the DC12v 4ah or 7ah Battery Pay close attention to POSITIVE(+) and NEGATIVE(-) Terminals. If the wires are connected incorrectly the control board will be damaged The control board will be forced to enter into sleeping mode when battery is low, during the sleeping mode, the control system will stop working until the battery has recovered

11 Step1. Press and hold LEARN CODE button for several seconds Step2. Release the LEARN CODE button until LED1 and LED2 flash at the same time Step3. LED1 and LED2 go out. Now all remote codes have been erased Step1. Press the LEARN CODE button, the LED2 will flash, then press REMOTE BUTTON A the LED2 stops flashing. Now the code is stored Press the REMOTE BUTTON A you can operate the gate for full open, with each press the gate will enter into open-stop-close cycle Step2. Press LEARN CODE button again, the LED1 will flash, then press REMOTE BUTTON B the LED1 stops flashing. Now the new code is stored. Press the REMOTE BUTTON B you can operate the gate for pedestrian open If the open/close time isn't learned, the gate cant open and close completely. If the directions of motor running is reversed. Please exchange the two motor terminal wires The open/close time learning might not be done successfully if you don't set motor force properly to overcome gate weight. Please refer to next page Step1. With gate in fully closed position Press LEARN TIME button, the LED3 is on, then press SET button, the motor will enter into time learning mode automatically as the following: The gate will open first when it reaches the position which you want it to start soft stop you press SET button, then the gate will start soft stop when the gate reaches the fully open position allow 3 extra seconds then press SET button. The gate will stop and start to close. When the gate reaches the position you want it to start soft stop press set button, the gate will start soft stop. When the gate reaches the fully closed position allow 3 extra seconds then press set button. The gate will stop working and a beep will be heard Step2. Now open/close time learning is successful. Press remote button to operate. The gate will know which position to soft stop and stop working. If the open/close time learning is not successful please repeat the above steps

12 Motor stall force (while gate is running quickly) Turn it clockwise to increase stall force, turn it counter clockwise to decrease stall force. The stall force must be adjusted to overcome the weight and size of the gate The stall force must be adjusted to have auto stop and reverse while gate is closing and runs into obstacle Motor Soft stop force (while gate is running slowly) Turn it clockwise to increase soft stop force, turn it counter clockwise to decrease soft stop force. The soft stop force must be adjusted to overcome the weight and size of the gate The soft stop force must be adjusted to have auto stop when gate runs into obstacle or ground stop block AUTO CLOSE TIME Turn it counter clockwise all the way to OFF will turn autoclose function off. Turn it clockwise turns autoclose function on auto close time is adjustable from 0 to 240secs Photocell is a safety device for protection against entrapment. When there is an obstacle during closing (photo beam is broken), the gate (s) will stop and reverse in the slow speed mode until fully open or hits obstacle. After the photo beam is clear the gate (s) will close automatically. The output signal is normally closed circuit PB1 and COM terminals are for push button, with each press the gate will enter into open stop close cycle. PB2 and COM are for exit wand the gate will open and auto close (if auto close is not enabled the gate will stay open)

13 Keypads & Push Buttons Opening your gate with push buttons It is recommended to have auto close function turned on so your gate closes after a preset time (30secs for example) WIRELESS PUSH BUTTONS You can use the wireless push button REF-WPB available from This functions like a remote control would. Simply learn it into the control board as you would a remote control. Channel 1 operates the gate fully same as PB1 input channel 2 operates the Pedestrian mode either 4 or 9 seconds opening WIRED PUSH BUTTONS Wire the push button into terminals PB1 the button will have the same function as remote control PB2 This input only tells the gate to open (then auto close if turned on) this is the recommended input for push buttons You can control the functioning times of day the push buttons will work by using a Latching timer, example disable the buttons at night by wiring them through a timer. Timer REF-TM619 Latching Timer available from WIRED PUSH BUTTONS WITH LATCHING TIMER To wire a timer to isolate the operation times of push buttons or other entry/exit devices follow this simple diagram. Timer REF-TM619 Latching Timer available from

14 Automatic opening & closing using timers Pulse Timer if auto-close is turned off If you have chosen to operate your gate with the auto close function turned off.( press to open press to close) You can connect a pulse timer to Automatically open and close the gate at set times of the day Pulse timer REF-TM618-S available from You would connect the pulse timer to PB1 input. Please follow the below diagram STEP The pulse timer simulates a press off a button for example if you set if you wanted your gate open between 7am and 5pm you would program the timer to come on at 7am and again at 5pm. When the timer comes on it sends a quick pulse to the input as if you were there pressing the button or remote control. WARNING IF YOU CLOSE YOURE GATE DURING THE DAY FROM THE REMOTE CONTROL THE TIMER WILL OPEN IT AGAIN AT THE NEXT PRESET ON TIME remember this is simulating the press of a button TM618-S Programming instructions KEY PROGRAMMING 1 PRESS TIMER SETTING 1 ON TIME (display 1 on) 2 PRESS H+/M+ SETTING HOURS AND MINUTES GATE OPENS 3 PRESS D+ SELECT SAME EVERYDAY, DIFFERENT EVERYDAY MO-FR, MO-SA, SA-SU, MO WE FR, TU TH SA, MO-WE, TH-SA (If same everyday no need to press this key 4 PRESS TIMER SETTING 1 OFF TIME (display 1 off) 5 PRESS H+/M+ SETTING HOURS AND MINUTES GATE CLOSES 6 PRESS D+ IF YOU WANT SAME SET IN EVERYDAY, YOU NEED NOT PRESS THIS KEY 7 REPEAT STEP 2-6 SET 2-16 ON/OFF TIME IF YOU WANT MORE THAN 1 AUTO OPEN/CLOSE PER DAY 8 PRESS C/R END Page 13

15 Automatic opening & closing using latching timer power saving photocell function When the timer comes on the gate is opened and the power to the safety beam is disconnected saving valuable battery reserves when operating from solar power. When the timer switches off the power is restored to the safety beams then the gate will close after the normal auto close delay time Latching Timer if auto-close is turned on If you have chosen to operate your gate with the auto close function turned on.( press to open - gate closes after preset delay) You can connect a latching timer and relay to Automatically open and close the gate at set times of the day Latching timer REF-TM619 available from Page 15

16 Automatic opening using Beams When the beam is broken the gate will automatically open. This method is ideal if you want free entry or exit from your property for Pedestrians, Vehicles etc. Not recommended if you are trying to keep animals in as they too will break the beam and open the gate Page 16

Instruction Manual for the. E-SL 450 Series

Instruction Manual for the. E-SL 450 Series Instruction Manual for the E-SL 450 Series Estate Slide Summary of Functions The Estate Slide is only to be used for vehicular Slide gates in a Class I setting. Class I: A vehicular gate opener (or system)

More information

Installing the gate post bracket with the cardboard arm template

Installing the gate post bracket with the cardboard arm template ......... Installing the gate post bracket with the cardboard arm template... Installing gate posts brackets and arms for Push-to-Open or Pull-to-Open gates... Connection of Power Source 240Vac or Solar...

More information

Installing the gate post bracket with the cardboard arm template

Installing the gate post bracket with the cardboard arm template ......... Installing the gate post bracket with the cardboard arm template... Installing gate posts brackets and arms for Push-to-Open or Pull-to-Open gates... Connection of Power Source 240Vac or Solar...

More information

DKC400Y AC Sliding Gate Installation Manual. Sliding Gate Opener. Model: DKC400Y. Installation Manual WARNING

DKC400Y AC Sliding Gate Installation Manual. Sliding Gate Opener. Model: DKC400Y. Installation Manual WARNING Sliding Gate Opener Model: DKC400Y Installation Manual WARNING Read and thoroughly understand all instructions before installing or operating this automatic gate opener. Failure to do so may cause serious

More information

SWING GATE OPENER SW300 SERIES

SWING GATE OPENER SW300 SERIES USER'S MANUAL SWING GATE OPENER SW300 SERIES 2.50m max. 250kg max. 2.50m max. 250kg max. Important Safety Advice: 1. Knowledge of the relevant electro-technical regulations is required. 2. Training in

More information

Safety Installation Information Single Gate Opener Parts List...4. Dual Gate Opener Parts List...5. Technical Specifications & Features...

Safety Installation Information Single Gate Opener Parts List...4. Dual Gate Opener Parts List...5. Technical Specifications & Features... Table of Contents ` Safety Installation Information..... 2-3 Single Gate Opener Parts List.........4 Dual Gate Opener Parts List........5 Technical Specifications & Features...........6-7 Installation

More information

Gate Operators, Inc. Model 7100UL Residential & Medium Duty Commercial Slide Gate Operator INSTALLATION MANUAL

Gate Operators, Inc. Model 7100UL Residential & Medium Duty Commercial Slide Gate Operator INSTALLATION MANUAL Gate Operators, Inc. Model 7100UL Residential & Medium Duty Commercial Slide Gate Operator INSTALLATION MANUAL 10-04-00 CONTENTS Safety Precautions... 2 Applications... 3 Pre-Installation Checklist...

More information

User manual. e-gate SLD-24V

User manual. e-gate SLD-24V User manual FOR e-gate SLD-24V 24V Sliding Gate Operators Contents how to use your automatic gate operator...... 1 how the controls work.................. 2 how to manually release the gate...........

More information

CHECKLIST & COMPONENTS

CHECKLIST & COMPONENTS Eclipse Compact www.rollershuttercompany.com Tel 0800 6444121 55mm Roller Garage Doors CHECKLIST & COMPONENTS EQUIPMENT REQUIRED 2 x Step ladders or hop ups Spirit level Tape measure Power drill 10mm A/F

More information

Table of Contents. General Safety Preparation for Installation Parts List Optional Accessories Part List... 5

Table of Contents. General Safety Preparation for Installation Parts List Optional Accessories Part List... 5 REV 12a Table of Contents General Safety....... 2 Preparation for Installation....... 3 Parts List....... 4 Optional Accessories Part List...... 5 Technical Specifications & Feature...... 5 Installation

More information

Owner s Manual. For SOLAR BOOM GATE. Model: CA-5000 SOLAR

Owner s Manual. For SOLAR BOOM GATE. Model: CA-5000 SOLAR ECA Electronic Engineering Pty. LTD. Australia Tel: 03-95720 535 Fax: 95 720 536 Owner s Manual For SOLAR BOOM GATE Model: CA-5000 SOLAR ( 2009 / Version 1 ) 1 1 Introduction 1.0 Control PCB Wiring INSTALLATION

More information

Gate & Door Controller with LCD and Intelligent Technology

Gate & Door Controller with LCD and Intelligent Technology 2nd Edition Gate & Door Controller with LCD and Intelligent Technology 24Sv1 and 12Sv1 Motor Controllers Setup and Technical information for single motor controller for gates & doors Includes latest Intelligent

More information

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN SYMBOL LEGEND DANGER THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN WARNING THIS WARNS THAT MATERIALS MAY BE DAMAGED IF APPROPRIATE PRECAUTIONS ARE NOT

More information

LI-2B Installation Manual

LI-2B Installation Manual ARCO Pty. Ltd. LI-2B Intelligent Gate Controller Installation/Owners Manual Please do not commence installation until you have read this instruction book. Contents: Introduction Installation Options: Standard

More information

APOLLO Gate Operators, Inc.

APOLLO Gate Operators, Inc. APOLLO Gate Operators, Inc. Model BA12 12 VOLT DC BARRIER ARM OPERATOR INSTALLATION MANUAL 0707 CONTENTS IMPORTANT SAFETY INSTRUCTIONS... 3 Applications... 4 Pre-Installation Checklist... 5 Operator Installation...

More information

GARAGE DOOR OPENER OWNER S MANUAL S3/S4

GARAGE DOOR OPENER OWNER S MANUAL S3/S4 GARAGE DOOR OPENER OWNER S MANUAL S3/S4 Features! Locking door during power failure: If power failure occurs while the door is operating, the door can be released by pulling the clutch down, allowing

More information

TMT Boxer 24v slider motor installation notes from EasyGate

TMT Boxer 24v slider motor installation notes from EasyGate TMT Boxer 24v slider motor installation notes from EasyGate Install Physical Gate Stops Physical Gate Stops MUST be installed at each end of your gate. If the Limit Switch on the boxer motor fails to stop

More information

MOTORIZED ROLLER SHADES PROGRAMMING GUIDE OTTO 30 OTTO DC2

MOTORIZED ROLLER SHADES PROGRAMMING GUIDE OTTO 30 OTTO DC2 MOTORIZED ROLLER SHADES PROGRAMMING GUIDE OTTO 30 OTTO DC2 REMOTE CONTROL BASICS Wall Mount Holder Remove cover from base by prying with flat head screwdriver. Use supplied fasteners and anchors to attach

More information

GENERAL SAFETY... 3 PARTS LIST...

GENERAL SAFETY... 3 PARTS LIST... Rev 17a 1 GENERAL SAFETY... 3 PARTS LIST... 4 GTR100... 4 GTR058... 5 TECHNICAL SPECIFICATIONS... 6 FEATURES:... 6 QUICK INSTALLATION GUIDE... 7 GATE ARM INSTALLATION... 8 BEFORE YOU START... 8 INSTALLATION

More information

EstateSwing.com. Plug-in Option. E-S 1000H Series INSTRUCTION MANUAL

EstateSwing.com. Plug-in Option. E-S 1000H Series INSTRUCTION MANUAL EstateSwing.com Plug-in Option E-S 1000H Series INSTRUCTION MANUAL Estate Swing Summary of Functions The Estate Swing is only to be used for vehicular swing gates in a Class I setting. Class I: A vehicular

More information

V200 USER MANUAL SWING GATE OPENER. 100kg 1.5m. 100kg 1.5m

V200 USER MANUAL SWING GATE OPENER. 100kg 1.5m. 100kg 1.5m V200 USER MANUAL SWING GATE OPENER 100kg 1.m 100kg 1.m Content Important Safety Advice... Content of the Kit... Connection Diagram... Installation Guide... Actuator... Control box... AC cable wiring...

More information

APOLLO Gate Operators, Inc.

APOLLO Gate Operators, Inc. APOLLO Gate Operators, Inc. Model 3500ETL/3600ETL Commercial Swing Gate Operator INSTALLATION MANUAL 01/08 CONTENTS IMPORTANT SAFETY INSTRUCTIONS. 3 Applications... 4 Pre-Installation Checklist... 5 Parts

More information

FROG KIT. Installation Instructions for a Pair of gates... TECHNICAL HELPLINE THE FROG-P KIT CONSISTS OF:

FROG KIT. Installation Instructions for a Pair of gates... TECHNICAL HELPLINE THE FROG-P KIT CONSISTS OF: CAME UNITED KINGDOM LTD UNIT 3 ORCHARD PARK INDUSTRIAL ESTATE, TOWN STREET, SANDIACRE, NOTTINGHAM NG10 5BP TEL: 0115 921 0430 FAX: 0115 921 0431 TECHNICAL HELPLINE 0115 921 0430 INTERNET - www.cameuk.com

More information

Model 1550 Single Swing Gate Model 1650 Dual Swing Gate

Model 1550 Single Swing Gate Model 1650 Dual Swing Gate Gate Operators, Inc. Model 1550 Single Swing Gate Model 1650 Dual Swing Gate Swing Gate Operator CONTENTS Safety Precautions... 2 Applications... 3 Pre-Installation Checklist... 4 Parts Identification...

More information

www.wholesalegateopener.com REV 11C Table of Contents Safety Installation Information..... 2-3 Dual Gate Opener Parts List (902).....4 Single Gate Opener Parts List (901)......5 Optional Accessories Parts

More information

RA2 Installation Manual Rev. B

RA2 Installation Manual Rev. B Important Information Required Installation Tools Voltmeter Wire Strippers Electric Drill & Bits Phillips Screwdriver Convoluted Tubing * Solder Gun * Wire Crimpers Shrink Tube or Electrical Tape * Optional

More information

E-SL 450BD Series INSTRUCTION MANUAL WARNING USER DRIVEN MANUAL*

E-SL 450BD Series INSTRUCTION MANUAL WARNING USER DRIVEN MANUAL* USER DRIVEN MANUAL* Any feedback, changes, or advice we are glad to hear it. Please contact us at support@estateswing.com WARNING Read all instructions before beginning installation or use of this gate

More information

ROSSO EVO User s and Installer s manual

ROSSO EVO User s and Installer s manual ROSSO EVO User s and Installer s manual v1.0 REV. 01/2014 00. CONTENT 01. SAFETY INSTRUCTIONS INDEX STANDARDS TO FOLLOW 00. CONTENT index pag 01.A 01. SAFETY INSTRUCTIONS standards to follow pag 01.B 02.

More information

F ERNI K I T THE FERNI-S KIT CONSISTS OF:

F ERNI K I T THE FERNI-S KIT CONSISTS OF: CAME UNITED KINGDOM LTD ORCHARD PARK INDUSTRIAL ESTATE TOWN STREET, SANDIACRE, NOTTINGHAM, NG10 5BP TEL: 0115 921 0430 FAX: 0115 921 0431 INTERNET - www.cameuk.com E-MAIL - enquiries@cameuk.com TECHNICAL

More information

Linear Actuator Swing Gate Operator Installation Manual Model # LA405-24

Linear Actuator Swing Gate Operator Installation Manual Model # LA405-24 Linear Actuator Swing Gate Operator Installation Manual Model # LA405-24 2 Contents Contents Product Information and Specs. 3 Mechanical 3 Electrical, Line Connections 3 Electrical, Control Connections

More information

Sliding Gate Opener User s Manual

Sliding Gate Opener User s Manual Gat Model: Sliding Gate Opener User s Manual GA2500 Gate1Access, LLC. www.gate1access.com Email: support@gate1access.com 1 Thank you for purchasing GA2500 gear rack drive sliding gate opener. We are sure

More information

HYPPOETL HYPPO DUALETL 12 VOLT DC Swing Gate Operator

HYPPOETL HYPPO DUALETL 12 VOLT DC Swing Gate Operator HYPPOETL HYPPO DUALETL 12 VOLT DC Swing Gate Operator Manufactured by NICE SpA INSTALLATION MANUAL 08/10 CONTENTS IMPORTANT SAFETY INSTRUCTIONS... 3 Applications...... 4 Pre-Installation Checklist... 5

More information

Index. COMPACT domestic gate operator

Index. COMPACT domestic gate operator COMPACT domestic gate operator Index Introduction. 3. General motor layout 4. General site layout 5. Terms and definitions. 6.. Site evaluation. 6. Gate evaluation 7. Removing the lid 8. Placing the gate

More information

ZAP MOTOR AND CONTROL UNIT INSTALLATION MANUAL

ZAP MOTOR AND CONTROL UNIT INSTALLATION MANUAL ZAP MOTOR AND CONTROL UNIT INSTALLATION MANUAL Zap 815 Series Roll-Up Sheet Steel Door Operators ZAP CONTROLS UK 100 Waterloo Boulevard Anglesey Business Park Cannock Staffordshire WS12 1NR United Kingdom

More information

Buffalo America C Column Mountable Gate Opener WARNING

Buffalo America C Column Mountable Gate Opener WARNING Column Mountable Gate Opener WARNING Read all instructions before beginning installation or use of this gate opener. This operator exerts a high level of force. Exercise caution at all times and stay clear

More information

Installation and Set Up Instructions

Installation and Set Up Instructions SL 2000 DC2 SLIDING GATE MOTOR KIT Solar Powered and 12V Low Voltage Installation and Set Up Instructions Unit 27 / 49 Corporate Boulevard Bayswater Vic 3153 Phone 1800 111 930 Email info@gforceautogates.com.au

More information

GARAGE DOOR OPERATOR USER S MANUAL

GARAGE DOOR OPERATOR USER S MANUAL GARAGE DOOR OPERATOR USER S MANUAL - DOMESTIC USE CIL-CD800S Chain) CIL-BD800S Belt GARAGE DOOR OPENER OWNER S MANUAL - DOMESTIC USE CIL-CD800S CD800S(Chain Chain) CIL-BD800S BD800S(Belt Belt) 1 Features

More information

Sliding Gate Operator User's Manual

Sliding Gate Operator User's Manual Sliding Gate Operator User's Manual PY800AC/PY00AC. Products introduction Please read the instructions carefully before proceeding. MCU is supplied to control the gate operator. Keypad / single button

More information

Installation Guide Rollerdor RD55 Econ Roller Garage Door

Installation Guide Rollerdor RD55 Econ Roller Garage Door Installation Guide Rollerdor RD55 Econ Roller Garage Door 1 Finished door Rollerdor RD55 Econ Roller Garage Door CHECKLIST & COMPONENTS EQUIPMENT REQUIRED 2 x Step ladders or hop ups Spirit level Tape

More information

Hunter Automatics HA-8. Installation Manual

Hunter Automatics HA-8. Installation Manual Hunter Automatics HA-8 Installation Manual WARNING TO REDUCE RISK OF INJURY 1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE

More information

E-S Allegiant Series Single Swing and Dual Swing Gate Opener

E-S Allegiant Series Single Swing and Dual Swing Gate Opener Estate Swing brand gate openers are a Sequoia Brands, Inc. product. Please visit www.estateswing.com for manual updates and other product information This gate opener is low voltage and bolt on specifically

More information

PRODUCT MANUAL Gecko Wireless One Zone LED Dimmer and Receiver

PRODUCT MANUAL Gecko Wireless One Zone LED Dimmer and Receiver Product Description The Gecko Wireless One Zone Wall LED Dimmer has been designed to bring light control easily. No wires or switch box locations are needed, just stick or mount the Gecko to any flat location

More information

AUTOMATIC CONTROL ROLLING DOOR OPENER

AUTOMATIC CONTROL ROLLING DOOR OPENER AUTOMATIC CONTROL ROLLING DOOR OPENER INSTALLATION INSTRUCTION AUTOMATIC OBSTRUCT PHOTOELECTRIC BEAM ROLLING CODE SYSTEM AUTO CLOSE DOOR ANTI-THEFT SYSTEM INSTALLATION INSTRUCTION AND RDO OWNERS MANUAL

More information

TEL: G&C Electronics CC E. T.

TEL: G&C Electronics CC E. T. TEL: +27 21 448 6774 G&C Electronics CC FAX: +27 21 447 7794 E. T. CK 89/31531/23 E-mail : etsystems@icon.co.za Internet: www.et.co.za 15 Nelson Road P.O. Box 34524 Observatory Groote Schuur Cape Town

More information

Sectional And Tilting Door Opener

Sectional And Tilting Door Opener Sectional And Tilting Door Opener Installation Instructions and User Guide FS 600 FS 1000 FS 1200 600N 1000N 1200N FS 600-Speed FS 1000-Speed 600N 1000N S/N WARNING Please read the manual carefully before

More information

MOTORIZED ROLLER SHADES PROGRAMMING GUIDE OTTO RECHARGE OTTO RECHARGE PLUS OTTO RECHARGE MAX

MOTORIZED ROLLER SHADES PROGRAMMING GUIDE OTTO RECHARGE OTTO RECHARGE PLUS OTTO RECHARGE MAX MOTORIZED ROLLER SHADES PROGRAMMING GUIDE OTTO RECHARGE OTTO RECHARGE PLUS OTTO RECHARGE MAX REMOTE CONTROL BASICS Wall Mount Holder Remove cover from base by prying with flat head screwdriver. Use supplied

More information

WWWAUTO-ROLLER.CO.ZA INSTALLATION MANUAL AUTO- ROLLER

WWWAUTO-ROLLER.CO.ZA INSTALLATION MANUAL AUTO- ROLLER WWWAUTO-ROLLER.CO.ZA INSTALLATION MANUAL AUTO- ROLLER Notice. Please read these instructions carefully before installing the Rolling Door motor 1. The motor must be installed and operated by a professional.

More information

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN

SYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN SYMBOL LEGEND DANGER THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN WARNING THIS WARNS THAT MATERIALS MAY BE DAMAGED IF APPROPRIATE PRECAUTIONS ARE NOT

More information

CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM

CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM Installation And Operation Manual MEGATRONIX VAN NUYS, CA U.S.A. CP634 1 REMOTE CONTROL CONVENIENT SYSTEM INSTALLATION & OPERATION INSTRUCTIONS INTRODUCTION

More information

Job Sheet 6 Installing the Combiner Box

Job Sheet 6 Installing the Combiner Box Job Sheet 6 Installing the Combiner Box The Combiner Box The combiner box used in this course can combine photovoltaic (PV) solar sub-array strings that are up to 150 V DC each and up to 120 A total. Using

More information

Installation and Maintenance Manual

Installation and Maintenance Manual Installation and Maintenance Manual Swing Gate Operator Model HL410-21 & HL410L-21 2 Contents Contents Parts & Components 3 Specifications & Capacities 4 Safety Information 6 Installer 6 End User 7 General

More information

Congratulations on purchasing the epump solar pumping solution.

Congratulations on purchasing the epump solar pumping solution. Congratulations on purchasing the epump solar pumping solution. Please follow the easy step by step assembly instructions below. We also have an assembly video which can be viewed via our website Assembly

More information

Sliding Gate Operator User's Manual

Sliding Gate Operator User's Manual Sliding Gate Operator User's Manual SL600AC. Products introduction Please read the instructions carefully before proceeding. MCU is supplied to control the gate operator. Keypad / single button interface.

More information

Installation Manual CS9300-LED. Professional Series Landscape Lighting System

Installation Manual CS9300-LED. Professional Series Landscape Lighting System Installation Manual CS9300-LED Professional Series Landscape Lighting System CS9300 Professional Series LED Landscape Lighting System pg. 1 READ THESE INSTRUCTIONS ENTIRELY BEFORE BEGINNING INSTALLATION!

More information

SECEUROGLIDE ROLLER GARAGE DOORS, SECEUROSHIELD, SECEUROSCREEN & SECEUROVISION ROLLER SHUTTERS CONTENTS

SECEUROGLIDE ROLLER GARAGE DOORS, SECEUROSHIELD, SECEUROSCREEN & SECEUROVISION ROLLER SHUTTERS CONTENTS Operating & Maintenance Instructions SECEUROGLIDE ROLLER GARAGE DOORS, July 2007 Issue 4 SECEUROSHIELD, SECEUROSCREEN & SECEUROVISION ROLLER SHUTTERS CONTENTS Page 1. General Instructions 2 2. Operating

More information

Sliding Gate Operator. User's Manual WARNING THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN

Sliding Gate Operator. User's Manual WARNING THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN Sliding Gate Operator User's Manual WARNING THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN BMG Imports Sliding Gate Opener MODEL No. LW550 Power rating: 220-240v AC 50Hz 550w Duty Close: 0-120

More information

AUTOMATIC SPRINKLER TIMER

AUTOMATIC SPRINKLER TIMER AUTOMATIC SPRINKLER TIMER Owner s Manual PRT-4 / PRT-6 For use with standard 24 VAC automatic sprinkler valves. These timers are designed for use in any 110 VAC /60 Hz ±10% AC outlet (240 VAC, 50 HZ for

More information

Installation and Set Up Instructions

Installation and Set Up Instructions SL SLIDING GATE MOTOR KIT Solar Powered and 12V Low Voltage Installation and Set Up Instructions Unit 27 / 49 Corporate Boulevard Bayswater Vic 3153 Phone 1800 111 930 Email info@gforceautogates.com.au

More information

IMPORTANT! Remote Control Instructions

IMPORTANT! Remote Control Instructions Remote Control Instructions FOR New Tarp Remote Control Installation Use these in place of the rocker switch and solenoid section of instructions in your roll tarp owner s manual. FOR Existing Electric

More information

GLM SERIES CONTROL Users Manual Rev:

GLM SERIES CONTROL Users Manual Rev: GLM SERIES CONTROL Users Manual Rev: 808062 Connecting Power Page 2 Motor Terminal Wiring Diagrams Page 3 Getting Started / Setup Page 4 1. Obstruction Detection Devices Page 4 2. Checking Power and Direction

More information

OPERATING INSTRUCTIONS IC-2, 3,4,5,6 INTELLICUT SERVO CUTTER Version 5.1xx Created 11/2009

OPERATING INSTRUCTIONS IC-2, 3,4,5,6 INTELLICUT SERVO CUTTER Version 5.1xx Created 11/2009 OPERATING INSTRUCTIONS IC-2, 3,4,5,6 INTELLICUT SERVO CUTTER Version 5.1xx Created 11/2009 "CAUTION" "DO NOT OPERATE MACHINE WITH GUARD REMOVED" UNCRATE AND INSPECT This machine has been carefully crated

More information

ELSEMA Single / Double Gate Controller, with Battery Charger, for 12V / 24V Motor, Enclosed, GATCOxxxCH

ELSEMA Single / Double Gate Controller, with Battery Charger, for 12V / 24V Motor, Enclosed, GATCOxxxCH GATCO12SCH, GATCO24SCH, GATCO12DCH, GATCO24DCH Single / Double Gate Controller, with Battery Charger, for 12V / 24V Motor Features 4 Versions: GATCO12SCH 12V Single motor GATCO24SCH 24V Single motor GATCO12DCH

More information

AUTOMATIC GATE LOCK. Installation Manual

AUTOMATIC GATE LOCK. Installation Manual IMPORTANT: Before you install the automatic gate lock be sure your gate is level, moves freely on its hinges, and does not bind or drag against the ground. AUTOMATIC GATE LOCK Installation Manual PLEASE

More information

PRODUCT MANUAL Gecko Wireless 2 Zone LED Dimmer and Receiver

PRODUCT MANUAL Gecko Wireless 2 Zone LED Dimmer and Receiver Product Description The Gecko Wireless 2 Zone Wall LED Dimmer has been designed to bring light control easily. No wires or switch box locations are needed, just stick or mount the Gecko to any flat location

More information

KIT-STCS60D KIT-STCS100D Solar Suitcase 60W and 100W Owner s Manual

KIT-STCS60D KIT-STCS100D Solar Suitcase 60W and 100W Owner s Manual KIT-STCS60D KIT-STCS100D Solar Suitcase 60W and 100W Owner s Manual RNG Group Inc. (Renogy) 14288 Central Ave., Suite A Chino, CA 91710 1-800-330-8678 Product Description The Renogy Solar Suitcases combine

More information

Installation and Set Up Instructions

Installation and Set Up Instructions Model FG 5-7 / SW 5-7 / DSW 5-7 Swing Gate Motor Kit Solar powered and 12V Low Voltage Installation and Set Up Instructions Unit 27 / 49 Corporate Boulevard Bayswater Vic 3153 Phone 1800 111 930 Email

More information

DOMESTIC SLIDING GATE OPERATOR

DOMESTIC SLIDING GATE OPERATOR D Turbo Pocket mechanical installation guide TM DOMESTIC SLIDING GATE OPERATOR This guide is designed specifically for installers who are familiar with the installation of standard sliding gate motors,

More information

MASTER SALT SAND SPREADER WIRELESS CONTROL MANUAL

MASTER SALT SAND SPREADER WIRELESS CONTROL MANUAL MASTER SALT SAND SPREADER WIRELESS CONTROL MANUAL This manual covers 1. Gas spreader wireless controllers (Standard) 2. Gas spreader wireless controllers (Plus) 3. 600DC single motor spreader wireless

More information

Lippert Components, Inc. Informational Publication ENTRY DOOR LATCH INFORMATION - SOUTHCO

Lippert Components, Inc. Informational Publication ENTRY DOOR LATCH INFORMATION - SOUTHCO Lippert Components, Inc. Informational Publication LIP Sheet - 0182 revd ENTRY DOOR LATCH INFORMATION - SOUTHCO SOUTHCO, Inc. door latches are used in Lippert s Keyless Entry Door systems. All Southco

More information

DMR 3005 WM ONE ZONE WIRELESS DIMMER RECEIVER

DMR 3005 WM ONE ZONE WIRELESS DIMMER RECEIVER E363518 DMR 3005 WM ONE ZONE WIRELESS DIMMER RECEIVER 20725 NE. 16 AVE. #A-33 MIAMI, FLORIDA 33179 Tel: (305) 652-2599 Fax: (305) 650-8812 www.lumiron.com Email: sales@lumiron.com 1 Benefits and Features

More information

DESIGNED FOR RESIDENTIAL APPLICATION KIT PL600/PL1000 SLIDING GATE OPENERS

DESIGNED FOR RESIDENTIAL APPLICATION KIT PL600/PL1000 SLIDING GATE OPENERS SLIDING GATE OPENER DESIGNED FOR RESIDENTIAL APPLICATION KIT PL600/PL1000 SLIDING GATE OPENERS The strongest solution for sliding gates PL600/PL1000 electro-mechanical sliding gate openers are designed

More information

ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY

ASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY 00 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) Track Assembly (0-) / Replacement

More information

HIGH SPEED SLIDING GATE OPENER

HIGH SPEED SLIDING GATE OPENER HIGH SPEED SLIDING GATE OPENER Model: is1200 + Elsema s Eclipse Control Card with GDS Operator USER MANUAL CONTENTS Section No: Page No: 1 Safety Precautions 3 2 Wiring Requirements 4 3 Installation details

More information

Do isolate the power supply from other high power systems such as Stereos and Alarms

Do isolate the power supply from other high power systems such as Stereos and Alarms Thank you for purchasing a Smart Ride Air Management System, AIRBAGIT.COM s premier flagship product. This system will meet all of your custom and utility needs and will provide you years of trouble free

More information

PY600AC Sliding Gate Opener User Manual

PY600AC Sliding Gate Opener User Manual PY600AC Sliding Gate Opener User Manual 2017 Dear users, Thank you for choosing this product. Please read the manual carefully before assembling and using it. Please do not leave out the manual if you

More information

Operators, Inc. Model 1550ETL Single Swing Gate Operator Model 1650ETL Dual Swing Gate Operator INSTALLATION MANUAL 04/07

Operators, Inc. Model 1550ETL Single Swing Gate Operator Model 1650ETL Dual Swing Gate Operator INSTALLATION MANUAL 04/07 APOLLO Gate Operators, Inc. Model 1550ETL Single Swing Gate Operator Model 1650ETL Dual Swing Gate Operator INSTALLATION MANUAL 04/07 CONTENTS IMPORTANT SAFETY INSTRUCTIONS... 3 Applications... 4 Pre-Installation

More information

SECTIONAL AND TILTING DOOR OPENER INSTALLATION INSTRUCTIONS AND USER GUIDE. Comfort 800E/1000E

SECTIONAL AND TILTING DOOR OPENER INSTALLATION INSTRUCTIONS AND USER GUIDE. Comfort 800E/1000E SECTIONAL AND TILTING DOOR OPENER INSTALLATION INSTRUCTIONS AND USER GUIDE Comfort 800E/1000E WARNING Please read the manual carefully before installation and use. The installation of your new door opener

More information

CHUBBSAFES EVOLVE INSTRUCTION MANUAL

CHUBBSAFES EVOLVE INSTRUCTION MANUAL CHUBBSAFES EVOLVE INSTRUCTION MANUAL 1 Ref: BASS-0010-B/21.02.2014 Table of content 1- CHARACTERISTICS... 4 1-1 Models... 4 1-2 Dimensions & Weights... 4 1-3 Interior fittings (standard and optional)...

More information

Aopec Dual Battery Kit Fitting Instructions

Aopec Dual Battery Kit Fitting Instructions AOPEC USA LLC. 1911 US Hwy 301 Suite 460 Tampa, FL 33619 Tel: 813-450-2156 Fax: 813-450-2638 www.aopec.com Aopec Dual Battery Kit Fitting Instructions Aopec Dual Battery Kit Fitting Instructions Fitment

More information

CONTENTS INTRODUCTION

CONTENTS INTRODUCTION CONTENTS INTRODUCTION 2 Lubrication 3 Physical dimensions 4 Technical specifications 5 STANDARD INSTALLATION KIT 6 WARNINGS 7 INSTALLATION OF THE UNIT 8 Initial preparations and mounting the base plate

More information

Installation Guide Rollerdor RD55 Econ Roller Garage Door

Installation Guide Rollerdor RD55 Econ Roller Garage Door Installation Guide Rollerdor RD55 Econ Roller Garage Door 1 Finished door Rollerdor RD55 Econ Roller Garage Door CHECKLIST & COMPONENTS EQUIPMENT REQUIRED 2 x Step ladders or hop ups Spirit level Tape

More information

ROSSO EVO USER'S AND INSTALLER'S MANUAL. v2.3 REV. 01/2015

ROSSO EVO USER'S AND INSTALLER'S MANUAL. v2.3 REV. 01/2015 ROSSO EVO USER'S AND INSTALLER'S MANUAL v2.3 REV. 01/2015 00. CONTT 01. SAFETY INSTRUCTIONS INDEX STANDARDS TO FOLLOW 01. SAFETY INSTRUCTIONS STANDARDS TO FOLLOW 02. PACKAGE INSIDE THE PACKAGE 03. THE

More information

Installation and Maintenancee Manual

Installation and Maintenancee Manual Installation and Maintenancee Manual Commercial Boom Gate Operator Model: GDS BOOM 4 and 6 A.B.N. 62 059 806 405 Nov 2013 Section No: CONTENTS Page Number: 1 Safety Precautions 3 2 Specifications 4 3 Mechanical

More information

MIDTOWN INSTRUCTIONS. White, Silver, Black. Single Light. MIDTOWN LED Recessed Light Installation Guide LED RECESSED LIGHT. (The nuts & bolts)

MIDTOWN INSTRUCTIONS. White, Silver, Black. Single Light. MIDTOWN LED Recessed Light Installation Guide LED RECESSED LIGHT. (The nuts & bolts) Single Light (The nuts & bolts) White, Silver, Black LED Recessed Light Installation Guide To avoid electric shock, disconnect the power to your ceiling fixture prior to installation.. Make sure the power

More information

Rolling Door Opener INSTALLATION INSTRUCTION AND OWNERS MANUAL

Rolling Door Opener INSTALLATION INSTRUCTION AND OWNERS MANUAL Rolling Door Opener INSTALLATION INSTRUCTION AND OWNERS MANUAL IMPORTANT SAFETY INFORMATION FAILURE TO COMPLY WITH THE FOLLOWING SAFETY RECOMMENDATIONS MAY RESULT IN SERIOUS PERSONAL INJURY, DEATH AND

More information

SWING GATE OPENERS 24V DC GEAR MOTOR

SWING GATE OPENERS 24V DC GEAR MOTOR SWING GATE OPENERS 24V DC GEAR MOTOR FOR RESIDENTIAL USER MANUAL Flashing Light Push Button Control box Gate 2 Gate 1 Index 1. Warnings 2 4. Technical Characteristics 16 2. Product Description 2.1 Applications

More information

Height extensions. Basic Operating Instructions. Number of boxes in lot

Height extensions. Basic Operating Instructions. Number of boxes in lot Height extensions Basic Operating Instructions Number of boxes in lot INFORMATION YOU MUST TAKE HEED OF THE GATE UNITS THAT THE HEIGHT EXTENSIONS FIT TO ARE STANDARD 2.3 (SINGLE) OR 4.6 DOUBLE GATES. THE

More information

Cross Hare Installation Guide

Cross Hare Installation Guide Cross Hare Installation Guide Introduction: The Cross Hare is designed to provide all of the functions you need to control a one or two track grade crossing in a prototypical manner. The Cross Hare uses

More information

PRODUCT MANUAL Onyx 2 Zone In-Wall Wireless LED Dimmer and Receiver

PRODUCT MANUAL Onyx 2 Zone In-Wall Wireless LED Dimmer and Receiver Product Description Main Functions: Control Up to 2 Zones Independently Wireless Control for Quick and Easy Installation Touch Sensitive Dark Glass Surface 50 Foot Wireless Range Soft Touch On/Off Memory

More information

DUCATI Control box. DUCATI Kontrol large DUCATI Kontrol small 10. PREDISPOSITIONS

DUCATI Control box. DUCATI Kontrol large DUCATI Kontrol small 10. PREDISPOSITIONS DUCATI Control box 10. PREDISPOSITIONS Prepare the insulated cable ducts for motors and accessories wires (not supplied). Prepare the power plant to the location where you intend to attach the control

More information

SKC-500DC SLIDING GATE OPENER OWNER S MANUAL

SKC-500DC SLIDING GATE OPENER OWNER S MANUAL SKC-500DC SLIDING GATE OPENER OWNER S MANUAL OUTLINE 1. Safety Precautions 2. Features 3. Specifications 4. Necessary Tools 5. Site Preparation 6. Mechanical Installation 7. Electrical Installation 8.

More information

HÖRMANN DSA 100 DSA 100 L DSA 200 DSA 200L. page 1

HÖRMANN DSA 100 DSA 100 L DSA 200 DSA 200L. page 1 HÖRMNN Spindle drive operator for hinged gates DS 100 DS 100 L DS 200 DS 200L Installation Instructions page 1 1 Overview of spindle drive operator for hinged gates E F a e f C b c D d g Table 1: Drive

More information

Automatic Sliding Door Retrofit Drive Assembly. Installation Manual DoorControlsUSA.com

Automatic Sliding Door Retrofit Drive Assembly. Installation Manual DoorControlsUSA.com Automatic Sliding Door Retrofit Drive Assembly Installation Manual 800-437-3667 DoorControlsUSA.com TABLE OF CONTENTS pg. 1. COMPONENTS 2 2. HEADER PREPARATION 2 3. DOOR PREPARATION 2 4. MOTOR AND CONTROLLER

More information

with Touch & Go Feature

with Touch & Go Feature Cellular Shades Veronica Valencia Blackout Cellular Shades POWER TOUCHTM RECHARGEABLE with Touch & Go Feature Installation & Care Instructions 152730 4/19/2017 GETTING STARTED A few simple tools are required:

More information

PW320/PW330 USER MANUAL SWING GATE OPENERS 24V DC GEAR MOTOR FOR RESIDENTIAL. Flashing Light. Push Button. Control box. Gate 2.

PW320/PW330 USER MANUAL SWING GATE OPENERS 24V DC GEAR MOTOR FOR RESIDENTIAL. Flashing Light. Push Button. Control box. Gate 2. PW320/PW330 USER MANUAL SWING GATE OPENERS 24V DC GEAR MOTOR FOR RESIDENTIAL Flashing Light Push Button Control box Gate 2 Gate 1 Declaration of Conformity Applicant: Powertech Electronics Inc. Manufacturer:

More information

BMW E61 Hydraulic Pump replacement instructions

BMW E61 Hydraulic Pump replacement instructions BMW E61 Hydraulic Pump replacement instructions This DIY will guide you through the tasks needed to successfully replace your defective tailgate hydraulic pump Difficulty 3 of 10. The most difficult part

More information

REMOTE CARAVAN MOVER Installation guide and user information. e-go /10/01/rev 3

REMOTE CARAVAN MOVER Installation guide and user information. e-go /10/01/rev 3 REMOTE CARAVAN MOVER Installation guide and user information Contents 1 1 Introduction 3 Parts List 4 Safety Guidelines 4 Technical Specifications 5 Fitting Guidelines (chassis adapters etc.) 6 Fitting

More information

O U T B A C K P R O O F G E A R 12V / 24V (MANUAL) O U T B A C K P R O O F G E A R

O U T B A C K P R O O F G E A R 12V / 24V (MANUAL) O U T B A C K P R O O F G E A R O U T B A C K P R O O F G E A R 12V / 24V (MANUAL) O U T B A C K P R O O F G E A R Ip68 Waterproof SOLAR BATTERY Mode MODE BUTTON Solar Panel Controller O U T B A C K P R O O F G E A R Ip68 Waterproof

More information

Installation Manual CS9100-LED. Professional Series Landscape Lighting System

Installation Manual CS9100-LED. Professional Series Landscape Lighting System Installation Manual CS9100-LED Professional Series Landscape Lighting System LED Landscape Lighting System pg. 1 READ THESE INSTRUCTIONS ENTIRELY BEFORE BEGINNING INSTALLATION! Congratulations on your

More information

Single or Double 240VAC motor control for domestic and industrial gates and doors.

Single or Double 240VAC motor control for domestic and industrial gates and doors. COBO30 Double 240V Motor Drive Controller Features For 240Volt Motors Auto Closing Open Only Security Closing and Extended Lock Pulse (user selectable) Travel Timer Push Button Input Photo Cell Input Option

More information