Purpose. Parts. Page 1 of 8
|
|
- Isabel Singleton
- 5 years ago
- Views:
Transcription
1 Page 1 of 8 SUBJECT: VL3500 Wash and VL3500 Wash FX 80 mm DC Fan Assembly SERIES: 3000 DISTRIBUTION: Authorized Service Centers & Dealers STATUS: Routine Purpose Vari-Lite has implemented a design improvement for VL3500 Wash and VL3500 Wash FX luminaires that improves the cooling capacity and life of the dual 80 mm fan assembly used in the Backend Assembly (Vari-Lite assembly number ). The new fans are powered by DC and run directly from the luminaire s Low-Voltage Supply (LVS). Note: This bulletin (S3K-020) is only for VL3500 Wash and VL3500 Wash FX luminaires, refer to Vari-Lite technical bulletin S3K-019 for all other Series 3000 TM fixture that use backend assembly All VL3500 Wash and VL3500 Wash FX luminaires manufactured after 04/11/10 will already have the new 80 mm DC fans installed. Read this procedure, in its entirety, before attempting any work. WARNING: The procedure contained within this bulletin should only be performed by Authorized VARI LITE Service Centers and Dealers. Parts EA 80MM DC FAN LAMP COOLING KIT (VL3500 WASH) CONSISTING OF: EA FAN SHIELD, LAMP COOLING, DC EA COUNTERWEIGHT, REAR EA FAN, TUBAXIAL, 80MM, 24VDC, LAMP COOLING EA NUT, 6-32 KEPS, ZINC EA SCREW, 6-32 X 3/8" LG PPZ EA SCREW, 6-32 X 1/2" LG PPB EA SCREW, 6-32 X 5/8" LG PPB EA CABLE TIE, 0.10" WD X 4.00" LG, SMALL EA #6 LOCK WASHER, ZINC VARI LITE, VLX, VL500, VL1000, VL2000, VL2500, VL3000, and VL3500 are trademarks of Vari-Lite, a Philips group company.
2 Page 2 of EA STANDOFF, 1/4" HEX 6-32 X 0.50" LG ZINC EA STANDOFF, 1/4" HEX 6-32 X 0.625" FF Tools #2 Phillips Screwdriver 7/16" Wrench or Needle Nose Pliers VL3500 Wash and VL3500 Wash FX Luminaires New-Style 80 MM Fan Assembly Replacement Procedure To install new-style 80 mm DC fan assemblies into luminaire: WARNING: Completely remove all power from luminaire before performing maintenance. Assemblies within the luminaire head may be HOT after operation. Allow to cool before proceeding. 1. Set luminaire on upper enclosure to have free access to luminaire head and enclosure assemblies. 2. COMPLETELY disconnect luminaire AC input cable from power source. WARNING: DO NOT reconnect power to luminaire until all steps of this procedure are complete and as instructed to do so. 3. As illustrated in Figure 1-1, at luminaire enclosure, remove top cover (cover is closest to AC input cable assembly) over Low-Voltage Supply (LVS) to access LVS. Top Cover Low-Voltage Power Supply (LVS) NOTE: Head not shown for clarity. Figure 1-1: VL3500 Wash / VL3500 Wash FX Low-Voltage Power Supply (LVS)
3 Page 3 of 8 4. At LVS, relocate spade connectors (with thin wires) as shown in Figure 1-2. WARNING: There are two Black and two White wires connected to "L" (Black wires) and "N" (White wires) terminals (each is crimped into a spade connector). It is important that only the smaller / thinner wires be relocated as indicated in Figure 1-2. The larger / thicker wires carry AC voltage from the supply source to power luminaire. Relocating the larger / thicker wires will damage the luminaire. Note: Some components removed for clarity. Wire Detail Twin THIN Black Wires Spade Connectors Twin THIN White Wires Low-Voltage Power Supply (LVS) Twin THIN Black Wires* - OLD Location (from "L" terminal) Twin THIN White Wires* - OLD Location (from "N" terminal) Twin THIN Black Wires* - NEW Location (to "-" terminal) Twin THIN White Wires* - NEW Location (to "+" terminal) Low-Voltage Power Supply (LVS) L N * See Wire Detail Figure 1-2: Series 3000 Low-Voltage Power Supply (LVS) Connections 5. Reinstall top cover on upper enclosure. Note, DO NOT connect power to luminaire until instructed to do so. 6. Remove top head and bottom head covers by loosening four quarter-turn captive locking screws (on each cover) as shown in Figure 1-3.
4 Page 4 of 8 Top Head Cover* 1/4-Turn Screw (4 per cover) Bottom Head Cover* * Head covers are attached by tethers. Figure 1-3: Top Head Cover Removal 7. At backend assembly, remove 80 mm fans, heat shields, and chrome fan guards as follows: a. Disconnect fans from cable assembly. b. At fan assembly, remove two 6-32 KEPS nuts and two 1/4" Hex Standoffs securing fans, shields, and insulator to Separation Bulkhead (see Figure 1-5 for details). c. As shown in Figure 1-4, remove chrome fan guards from each fan by removing four 6-32 x 3/8" PPZ screws and associated 6-32 KEPS nuts. Set chrome fan guards aside to be installed on replacement fans. Chrome Fan Guard 6-32 x 3/8" Screw (x4) 6-32 KEPS Nut (x4) Old Fan Assembly Figure 1-4: Chrome Fan Guard Removal Note: After removing old-style fans, only the chrome fan guards and dual fan insulator will be used to install the new-style fans. Old-style fans, fan shields, eight 6-32 x 3/8" PPZ screws, and eight #6 KEPS nuts will not be reused. Only the Screws, nuts, and shields, supplied with kit, should be used for new-style fan installation.
5 Page 5 of 8. Dual Fan Insulator Fan Shield (x2) 6-32 KEPS Nut (x2) 80 mm Fan Assembly (x2) Chrome Fan Guard (x2) 1/4" Standoff 6-32 x 0.50" (x2) Note: Other components removed for clarity. Figure 1-5: VL3500 Wash / VL3500 Wash FX 80 mm Fan Assembly Removal
6 Page 6 of 8 8. Install new-style 80 mm DC fans as follows: a. As shown in Figure 1-6, using two 6-32 x 3/8" PPZ screws and two 6-32 KEPS nuts, secure chrome fan guard to new 80 mm fan assembly. Repeat on other fan. Note orientation of fan - fan wires exit here 6-32 KEPS Nut (x2) Chrome Fan Guard 6-32 x 3/8" PPZ Screws (Note positions, install as shown) Figure 1-6: Fan Guard Installation b. Align and slip dual fan insulator (removed in 7) over threaded studs on Separator Bulkhead. c. Position new-style fan heatshield ( , 2 each) over threaded studs on Separator Bulkhead. Be sure reflective side is down towards lamp housing. Note: 80 mm fan on right-hand side in Figure 1-7 is rotated 90-degrees (versus left-hand fan). Fan shield will have to be oriented same as fan. Refer to Fan Shield note in Figure 1-7. d. Position 80 mm fan assemblies as shown in Figure 1-7 and slide onto Separator Bulkhead threaded studs. e. Install standoffs as illustrated in Figure 1-7. Be sure to install and tighten 6-32 x 0.050" standoff as shown first. This allows easier access to tighten neighboring (longer) standoff on other fan assembly. f. Install three 6-32 x 1/2" PPB and one 6-32 x 5/8" PPB (with #6 lock washer) screws as shown in Figure 1-7. g. Connect fan assemblies. Use tie wraps as needed to secure wiring.
7 Page 7 of 8 h. SEE DETAIL Fan Shield Fan Shield Struts Air Flow Direction Note: Some components removed for clarity. Application Notes: (A) Install reflective side down towards lamp housing. (B) Align and cover fan struts with shield struts. Fan Installation Detail Fan Shield (x2)* ( ) 1/4" Hex 6-32 x 0.50" Standoff (x1) - tighten first Note, this fan is rotated 90-degree clockwise. Fan Insulator (from removed fan assemblies) 6-32 x 5/8" PPB Screw (x1) / #6 Lock Washer (x1) 6-32 x 1/2" PPB Screw (x3) 1/4" Hex 6-32 x 0.625" Standoff (x3) Notes: *Reflective side down towards lamp housing. **Fan label side down towards lamp housing. Figure 1-7: VL3500 Wash and VL3500 Wash FX 80 mm Fan Installation
8 Page 8 of 8 9. At luminaire head backend (in two places), install additional counterweights (part number ) as follows: a. Rotate luminaire head so lens is pointing up. Steady luminaire head so it does not move. b. Starting one either side of luminaire head, remove seven 6-32 x 1" PPB screws securing counterweights and shown in Figure 1-8. Make sure existing counterweights do not move. c. Position one additional counterweight over existing counterweight plate holes and secure using seven 6-32 x 1" PPB screws removed from previous step. d. Repeat additional counterweight installation on other side of luminaire backend assembly. Existing Counterweights 6-32 x 1" PPB Screws (x7) Install Luminaire Head Counterweights (2 places as indicated) Note: Some components removed for clarity. Figure 1-8: VL3500 Wash and VL3500 Wash FX Luminaire Head Counterweights 10. Connect power to luminaire and make sure fans operate properly (note, air flow should be towards lamp housing). 11. After testing, turn off power to luminaire and reinstall top and bottom head covers on luminaire head assembly.
Purpose. Parts. Page 1 of 10
Page 1 of 10 SUBJECT: VL3500 Wash and VL3500 Wash FX 80 mm DC Fan Assembly SERIES: 3000 DISTRIBUTION: Authorized Service Centers & Dealers STATUS: Routine Purpose Vari-Lite has implemented a design improvement
More information,QWURGX WLRQ 10 minutes
Page 1 of 6 SUBJECT: VL2000 Optional Improvements: Color/Gobo Wheel SERIES: 2000 DISTRIBUTION: Service Centers, End Users STATUS: Routine,QWURGX WLRQ 10 minutes 3XUSRVH This technical bulletin contains
More informationS6 BATTERY REPLACEMENT
S6 BATTERY REPLACEMENT Supplemental Instruction Guide P/N 108304 Battery Pack Removal Tools Required: S6 Operation & Parts Manual, Phillips Head Screwdriver, Needle Nose Pliers, Wire Stripping / Crimping
More informationOwner smanual. Banks TorqueTube System. Jeep 2.5L 4-Cylinder '91-02 Wrangler. with Installation Instructions THIS MANUAL IS FOR USE WITH SYSTEM 51316
with Installation Instructions Owner smanual Banks TorqueTube System Jeep 2.5L 4-Cylinder '91-02 Wrangler THIS MANUAL IS FOR USE WITH SYSTEM 51316 Gale Banks Engineering 546 Duggan Avenue Azusa, CA 91702
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Security light Kit Maxima 999F4 AX009 - Universal Security Lighting Kit. Item QTY Description Service
More informationInstallation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#
Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,
More informationInstallation Instructions. PowerFlex 700 Drive - Frame 8 Components Replacement
Installation Instructions PowerFlex 700 Drive - Frame 8 Components Replacement Important User Information Solid-state equipment has operational characteristics differing from those of electromechanical
More informationOIL COOLER KIT CHEVY CAMARO 2.0T PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION TOOLS NEEDED NOTE INSTALL PROCEDURE
PARTS LIST AND PARTS INCLUDED 3PC APPLICATION-SPECIFIC MOUNTING BRACKETS 1PC HORN RELOCATION MOUNTING BRACKET 1PC 25-ROW OIL COOLER (SLEEK SILVER OR STEALTH BLACK) 1PC 4'4" STAINLESS STEEL BRAIDED HOSE
More informationSSX-300ST SolarMaxx 300 Illuminator
SSX-300ST SolarMaxx 300 Illuminator Service Manual 6018 Bowdendale Avenue Jacksonville, FL 32216 Customer Service: 904 731 5869 FAX 904 733 0012 Toll Free 800 684 6404 (English) TABLE OF CONTENTS Page
More informationSupply Valve Replacement
This procedure is to help facilitate the replacement of the25.1-25.4 supply valves. Solenoid Supply Valves Note: You will need the following tools: Socket Wrench with extension and a 3/8 Socket Size 1
More information09-12 Dodge 4WD Leveling Kit
9235900 09-12 Dodge 4WD 1500 2.5 Leveling Kit Thank you for choosing Rough Country for all your suspension needs. DOES NOT FIT TRX PACKAGE VEHICLES!! Rough Country recommends a certified technician install
More informationS4M Pulley and Gears Maintenance Kit
S4M Pulley and Gears Maintenance Kit Installation Instructions This kit includes the parts and documentation necessary to install the drive system maintenance kit into the S4M. Read these instructions
More information09-12 Dodge 4WD /4 Body Lift
92RC80000 09-12 Dodge 4WD 1500 1 1/4 Body Lift Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this kit. Attempts to install
More informationRT1 DUAL OUTLET SLIP-ON EXHAUST HONDA CBR600RR Rev B
18-1022-723-02 08 50 44541 Rev B PARTS INCLUDED Ref. Part Number Description Qty 1) 00-200-00042 Slip-on S-bend Assembly 1 2) 00-200-01197 Stainless Steel Dual Outlet Muffler 1 3) 03-46-42766 Muffler Mounting
More informationRT1 SLIP-ON EXHAUST HONDA CBR600RR REV. A
08-50-43733 REV. A PARTS INCLUDED Ref. Part Number Description Qty 1) 00-200-00064 Slip-on S-bend Assembly 1 2) 00-200-00088 RT1 Aluminum Muffler Assembly 1 3) 03-46-43058 Muffler Mounting Strap 1 4) 07-27-42566
More informationPARTS LIST. REPLACEMENT PARTS and ACCESSORIES PREPARATION VN1600. PREPARATION VN1500D and VN800B
INSTALLATION AND OWNER S MANUAL Light Bar N925 for Installation to: Kawasaki VN1500D&E and VN800B Pages 1,2,3 and 5 Kawasaki VN1600 Pages 1, 4 and 5 PARTS LIST QTY. PART NO. DESCRIPTION 1 N925 Light Bar
More informationTOYOTA im INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1
More informationTHIS GUIDE IS INTENDED FOR DEALERS AND SOLAR COMFORT TECHNICIANS ONLY AND IS NOT MEANT OR INTENDED TO BE REPRODUCED OR DISTRIBUTED TO THE CONSUMER
THIS GUIDE IS INTENDED FOR DEALERS AND SOLAR COMFORT TECHNICIANS ONLY AND IS NOT MEANT OR INTENDED TO BE REPRODUCED OR DISTRIBUTED TO THE CONSUMER Table of Contents Page Tools Needed (A) 3 Replacement
More informationOPTIMAX RADIANT FIELD RETROFIT INSTRUCTIONS
OPTIMAX RADIANT FIELD RETROFIT INSTRUCTIONS 99-24283-I001 Table of Contents 1. 24V LED Approved Drivers 5 1.1. 24V LED Driver (60-19910-0002).. 5 2. Optimax Radiant 24V LED Lighting. 6 2.1. OP30 6 2.2.
More information07-11 GM 1500 Pickup, Avalanche, Yukon, Tahoe, Suburban Front 2.5 Kit
92130500 07-11 GM 1500 Pickup, Avalanche, Yukon, Tahoe, Suburban Front 2.5 Kit Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install
More informationFRONT & 4 REAR GM WD LOWERING KIT
92725200 88-98 2 FRONT & 4 REAR GM 1500 2WD LOWERING KIT Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition
More informationBLACKBIRD INSTALLATION SUPPLEMENT
BLACKBIRD INSTALLATION SUPPLEMENT FOR 2008-105 FORD 6.4 LITER DIESEL F-SERIES VERSION 3/10 Parts Blackbird Wiring Manual Installation Supplement 6.4 liter Diesel Owner s Manual Includes Warrantee Registration
More informationInstructions for Front Midrange / Tweeter Installation in BMW 3 Series/M3 (E36)
Disclaimer: Bavarian Soundwerks highly recommends professional installation of the products we sell. We provide these installation instructions free of charge as a guide to assist those customers who choose
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationPredator Medium Floodlight Wet Location
Predator Medium Floodlight Wet Location Installation and Maintenance Manual AFTER INSTALLATION DELIVER THIS MANUAL TO OWNER IMPORTANT SAFETY INSTRUCTIONS -READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING
More informationTESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM
TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER
More informationPower Fuse Assembly Replacement (for 3000A 1395 DC Drives)
REPLACEMENT KIT INSTRUCTIONS Power Fuse Assembly Replacement (for 3000A 1395 DC Drives) Contents What This Kit Contains This document shows how to remove and replace a power fuse assembly (and how to replace
More informationCorkSport Mazdaspeed 3 ECU Relocation Box Mazdaspeed 3
CorkSport Mazdaspeed 3 ECU Relocation Box 2007-2013 Mazdaspeed 3 Thank you for purchasing the CorkSport ECU Relocation Battery Box for the Mazdaspeed 3. With the install of this battery box, you now have
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationRaxiom Mustang Headlights (94-98) - Installation Instructions
Raxiom Mustang Headlights (94-98) - Installation Instructions The below installation instructions work for the following products: Dark Smoked Mustang Headlights (94-98) Raxiom Chrome Mustang Headlights
More information07-11 GM 4WD 1500 P/U 1 1/4 Body Lift
92RC70100 07-11 GM 4WD 1500 P/U 1 1/4 Body Lift Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this kit. Attempts to install
More informationMAZDASPEED3 Intercooler Instructions
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
More informationInstallation Manual Volvo C30 T5 Front Mount Intercooler System
Installation Manual Volvo C30 T5 Front Mount System Volvo C30 T5 System / Installation Manual i C Contents Important Information i Parts List i Required Tools and Materials 1 1.0 - Vehicle Preparation
More informationCP2000 Ballast - Replacing Thyristor Instruction Sheet
CP2000 Ballast - Replacing Thyristor Instruction Sheet INTRODUCTION These instructions are for the CP2000 Ballast and explain how to: replace the existing 80 Amp Thyristor with a new 100 Amp Thyristor
More informationInstallation Instructions 1812 Folder Disk Clutch Retrofit Kit Martin Yale #WRA
Installation Instructions 1812 Folder Disk Clutch Retrofit Kit Martin Yale #WRA1812510 Background: Early production Martin Yale Model 1812 Folders were originally equipped with a spring-clutch type feed
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08E49-S2A-100 2004 S2000 AII 26325 Issue Date OCT 2003 PARTS LIST Hood switch harness TOOLS AND SUPPLIES REQUIRED #2 Phillips screwdriver
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory BACKUP S Application 2012 ODYSSEY Publications No. AII 46724 Issue Date SEP 2011 PARTS LIST Backup Sensor Attachment Kit P/N 08V67-TK8-100A Right center sensor clip
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Security Light Kit APPLICATION: Altima Coupe and Sedan (2011+) PART NUMBER: 999F4 AX008 - Universal Security Lighting Kit. KIT CONTENTS:
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from fire, electric shock, falling
More informationN/S= Not Shown Bold = Part available for purchase. Italic = Part not available for purchase, listed and shown for reference only.
Media Rewind Upgrade Installation Instructions Prepare for Installation This kit includes the parts and documentation necessary to install the media rewind option kit into the 105SL printers. Read these
More informationM7 R52S & R53 Cold Air Intake Installation Guide 53-3M7301
M7 R52S & R53 Cold Air Intake Installation Guide 53-3M7301 M7 Speed engineers and manufactures the highest quality MINI COOPER accessories and performance parts available anywhere on Planet Earth! Please
More informationMP and MP Diaphragm and Seal Kits for MP8000 Series Actuators
MP8000-6325 and MP8000-6350 Diaphragm and Seal Kits for MP8000 Series Actuators Contents of the MP8000-6325 Diaphragm and Seal Kit for MP82 and MP83 Actuators One seal, 5/8 in. Internal Diameter (I.D.)
More informationInstallation Manual TWM Performance Kia Forte Short Shifter
Installation Manual TWM Performance Kia Forte 2009+ Short Shifter Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral.
More informationI-Sheet Number Rev.B 3-1/2 OVAL BULL BAR DODGE RAM 1500
PARTS LIST: 1 Bull Bar 2 10-1.5mm x 35mm Hex Bolts 2 Tube Brackets (Bull Bar) passenger or driver side 2 10mm Lock Washers 2 Upper Frame Brackets (models w/o tow hooks only) 4 10mm x 27mm OD x 3mm Flat
More informationINSTALLATION MANUAL
INSTALLATION MANUAL 2563000 Parts List 1 Carrier weldment 2 Support arm assembly 1 Third brake light assembly 1 Light extension bracket 1 Spare tire adjustment plate 1 Spare tire mount plate 1 Female spade
More informationWD GM FRT 1.75 REAR LIFT KIT Thank you for choosing Rough Country for your suspension needs.
921277N201 2007-13 4WD GM 1500 3.5 FRT 1.75 REAR LIFT KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician install this system. In addition
More informationP-Series Installation
Utilimaster Access System Introduction P-Series Installation This information describes installation of the Utilimaster Access System (UAS) P-Series (one-button FOB) designed to replace the existing ACE
More informationIMPORTANT: When replacing the ignition lock cylinder only, the passlock relearn procedure is not required.
A 1 of 11 2/18/2012 3:27 PM IMPORTANT: The important statement at the beginning of the "Ignition Lock Cylinder removal procedure on page 188 in the 2000/2001 Saturn S-Series Body/Electrical Volume II Service
More informationSPORTSTER SADDLEBAG KIT. i i02212
General These saddlebags are designed to fit 99 and later Sportster Model Motorcycles, except XL00 Sport models with gas reservoir shock absorbers and 88R models. See the Service Parts pages for a list
More informationPARTS AND SERVICE MANUAL
PARTS AND SERVICE MANUAL FOR THE 23 INSERT FIREPLACE MODEL NUMBER: DFI2309 TABLE OF CONTENTS OPERATION PAGE 1 PARTS DRAWING PAGE 3 PARTS LIST PAGE 4 WIRING DIAGRAM PAGE 5 LIGHT BULB REPLACEMENT PAGE 6
More informationCOBB Tuning MAZDASPEED6 SF Intake System. Install Instructions
781500 COBB Tuning MAZDASPEED6 SF Intake System Install Instructions Congratulations on your purchase of the COBB Tuning SF Intake System. The following instructions will assist you through your installation
More informationIAG Street Series Air / Oil Separator (AOS) For 2017 WRX
P IAG Street Series Air / Oil Separator (AOS) For 2017 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flathead screwdriver,
More informationINSTALLATION INSTRUCTIONS PART NUMBER AEM C (GUN METAL GRAY FINISH)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER AEM-21-805C (GUN METAL GRAY FINISH) 2016.5-17 CHEVROLET CRUZE 1.4T ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2038DK
More informationOwner smanual. Banks TorqueTube System With Optional Headpipe Assembly
Owner smanual with Installation Instructions Banks TorqueTube System With Optional Headpipe Assembly Jeep 4.0L I-6 models including: 91-99 Wrangler 91-99 Cherokee 93-98 Grand Cherokee 91-92 Comanche THIS
More informationMazda 3 & Mazdaspeed 3 Oil Cooler Installation Instructions
Page1 2007-2009 Mazda 3 & Mazdaspeed 3 Oil Cooler Installation Instructions Tooling: Jack and jack stands or a lift Socket wrench and torque wrench 10mm and 14mm sockets 3/16 Allen wrench 10mm wrench Pliers
More informationVHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate (Refer to qualified
More informationThe HMC-Lite Construction Guide
The HMC-Lite Construction Guide The Heavy Metal-Lite Chassis is constructed using two identical drive modules. The drive modules are constructed using 3 mechanical sub-assemblies. The drive modules are
More informationVL2500 Parts List Description
VL2500 Parts List Item Description 10.9676.0071 SWIVEL PLATE, LAMP ADJUST 10.9676.0273 HEATSHIELD, COLOR SENSOR 10.9678.0869 BRACKET, LVS 10.9678.0886 SPACER, PAN BEARING 0.235" THK 10.9678.0892 BUSHING,
More informationPart number SP Hyundai genesis 2.0L turbo 4 cyl.
Part number SP1386 2010 Hyundai genesis 2.0L turbo 4 cyl. 1-1 piece Cold air intake system 1-3 1/2 Injen/AMSOIL Ea nano-fiber Performance Dry Filter (#1021) 1-1 1/8 x 3 long str. hose (#3109) 1-7 -10mm
More informationLIFT Standard A-Arm Lift Kit Club Car Precedent Installation Instructions
LIFT-563 6 Standard A-Arm Lift Kit Club Car Precedent Installation Instructions Contents of LIFT-563 Club Car Precedent Lift Kit: a (1 ea.) Front Suspension b (1 ea.) Driver Side Upper A-Arm c (1 ea.)
More informationHURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog # by Hurst Performance
FORM 159 0205 07/15 HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog #391 0205 2015 by Hurst Performance Thank you for purchasing the Hurst Comp/Plus Shifter.
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing
More informationSection One: Install the Constant Current DMX Driver
Intelligent LED Driver/Controller Output 060VDC, 0050mA, 0W SELV equivalent : 0% typ. in in out out Group Group LEDcode in in out out Group Group LEDcode 06 Edge Lighting. All Rights Reserved. Installation
More informationDEALER SETUP INSTRUCTION
DEALER SETUP INSTRUCTION P/N XXXXXXX APPLICATION 2018 GTS 150 BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation instructions
More informationadvanced FLOW engineering Instruction Manual P/N: / / Make: Toyota Model: Tacoma Year: Engine: V6-4.
advanced FLOW engineering Instruction Manual P/N: 51-76012 / 54-76012 / 75-76012 Make: Toyota Model: Tacoma Year: 2012-2015 Engine: V6-4.0L Please read the entire instruction manual before proceeding.
More informationSED2-BT300-XX-C09 Migration Kits. Product Numbers
Document No. 129-710 SED2-BT300-XX-C09 Migration Kits Product Numbers SED2-BT300-AB-C09 Migration Kit, SED2 FSAB 09 to BT300 FS4 * 208 Vac: Up to 3 hp 480 Vac: Up to 5 hp SED2-BT300-C4-C09 Migration Kit,
More informationELECTRICAL SYSTEM UPGRADE
NEW CONTROLLER & ELECTRICAL SYSTEM UPGRADE FOR DAIRY TECH, INCORPORATED 10, 30 & 60G PASTEURIZERS Parts to Include 2 Wire ties (Nuts) 2 sticky wire mount pads Large Rubber Grommet (for bottom of electric
More informationINSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter
INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter TOOLS REQUIRED: Phillips Screw Driver T-20 Torx bit Standard Socket set 9/64 Allen wrench
More information2011-up Polaris RZR 800* Cab Enclosure Kit. Caution: Before using this product, read this manual and follow all safety instructions.
Owner s Manual Model: Polaris RZR * 2011-up Polaris RZR 800* Cab Enclosure Kit Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions Kit Contents
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory (LX) Application 2008 ACCORD 2- AND 4-DOOR Publications No. AII 35373 Issue Date AUG 2007 PARTS LIST Automatic Day/Night Mirror Attachment Kit P/N 08V03-TA0-100 Fuse
More informationINSTALLATION AND OWNER S MANUAL Side Illumination Lights Z5150 for use with K 1200 LT
INSTALLATION AND OWNER S MANUAL Side Illumination Lights Z5150 for use with K 1200 LT Read these instructions carefully and thoroughly before beginning work. Before installing the accessory, carefully
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationCOLD WEATHER START KIT Ceiling Mount 8000
COLD WEATHER START KIT Ceiling Mount 8000 Cold Weather Start Kit: To be used in conjunction with Ceiling Mount 8000 (Manufactured After 01/07/15) cooling system. The Coolest Thing In Wine Storage CWSK.CM8000
More informationFRONT DROP SPINDLES
92725000 88-98 2 FRONT DROP SPINDLES Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these instructions,
More informationPart Number: S-H-BAG-8 & S-H-8-RFEN Description: Saddlebags & Rear Fender / Undertail Fitment: Suzuki GSX 1300-R Hayabusa Revision: 1
Part Number: S-H-BAG-8 & S-H-8-RFEN Description: Saddlebags & Rear Fender / Undertail Fitment: 2008-2009 Suzuki GSX 1300-R Hayabusa Revision: 1 Tools Required Phillips head screwdriver Small screwdriver
More informationPART NUMBER: H630SSJ000. Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4)
Kit Contents: A. Amplifier with Bracket (1) D. Badge (2) with push nuts (4) E. Clip B. Harness (1) C. Cable tie (8) F. Mounting Hardware (2) G. Replacement Speaker (2) H. HVAC Duct extension (2) IMPORTANT:
More informationElectrometer Lead Acid Battery Replacement
Electrometer Lead Acid Battery Replacement Table of Contents NOTE: Although this manual is provided by Standard Imaging as a reference, battery replacement by anyone other than a trained Standard Imaging
More information#TL T DOWNPIPES/ INSTALLATION INSTRUCTIONS
#TL100084 4.0T DOWNPIPES/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for on a North American specification RS7, but other models, like the S6 and S8, are similar. When disassembling
More informationPLEASE READ THIS INSTRUCTIONS CAREFULLY, BEFORE YOU START INSTALLATION
INSTALLATION INSTRUCTIONS PART NUMBER: L0SXC000 DESCRIPTION: 09 ASCENT TRAILER HITCH PLEASE READ THIS INSTRUCTIONS CAREFULLY, BEFORE YOU START INSTALLATION SAFETY PRECAUTION: When installing Trailer Hitch,
More informationInstalling an Auxiliary Pressure Control Module
Installing an Auxiliary Pressure Control Module Agilent 6850 GCs Accessory G3349B These instructions are divided into two parts: Part 1 to prepare the Auxiliary Electronic Pressure Control ("AuxEPC") module
More informationPART# Tri-Valve Exhaust For SL 17 A/B, 17 K, KM 37 & KMB 18/28 Band Masks
Tools needed: Medium size flat blade screwdriver PART# 525-752 Tri-Valve Exhaust For SL 17 A/B, 17 K, KM 37 & KMB 18/28 Band Masks Inch Pound Torque screwdriver with medium size flat blade Small cutting
More informationAssembly Instructions for A, A, A, & A
Update Instructions Yield-Pro 1225/1625 Planter Used with: Yield-Pro 1225 Planter Yield-Pro 1625 Planter General Information! When you see this symbol, the subsequent instructions and warnings are serious
More informationDVS Cypress Face Installation Instructions (SKU )
Table of Contents Compatibility... 1 Packing List... 1 Installation... 2 Prepare the Insert for Face Installation... 2 Attach the Surround Panels (if applicable)... 6 Assemble the Face... 7 Attach the
More informationPRP Seats 570/800/900 RZR 4 Doors
Install Instructions PRP Seats 570/800/900 RZR 4 Doors Remove all parts from the box and unwrap completely using the packaging to lay out the pieces. Tools Needed: (not included) 7/16 Open end wrench and
More informationInstallation Manual TWM Performance Short Shift Kit Estimated Installation Time: Tools required:
Page 1 Installation Manual TWM Performance Short Shift Kit 1993-2001 Nissan Altima 1991-2001 Infiniti G20 1991-2001 Nissan Sentra- 200SX 1991-1993 Nissan NX 1986-1989 Nissan Stanza 1995-2001 Nissan Maxima
More informationIAG Street Series Air / Oil Separator (AOS) For WRX
P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationService Bulletin. HIITMill (X) Brake Lever Drift
HIITMill (X) Brake Lever Drift Applies to: HIITMill (9-4590) + HIITMIll X (9-4640) On some HIITMill and HIITMill X units, the brake lever can drift when the user is Rev. A applying load to the belt. This
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi Document# Support:
INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi Document# 19-0102 Support: info@radiumauto.com These instructions are based on a vehicle with an OEM turbocharger
More information5.5 Wheel drive (wheel pilots only)
Chapter 5: Installing the ST4000+ 61 5.5 Wheel drive (wheel pilots only) The Raymarine wheel drive will fit 3, 4, 5, 6, 7 or 8 spoke wheels. It is designed to operate with steering systems with between
More informationIAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI
IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7150 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat
More informationLIFT-506 BMF Lift Kit Club Car DS Gas & Electric Installation Instructions
LIFT-506 BMF Lift Kit Club Car DS Gas & Electric 2003.5-09 Installation Instructions Contents of LIFT-506 Club Car DS BMF Lift Kit: a (1 ea.) BMF Front Suspension b (1 ea.) Driver Side Upper A-Arm c (1
More informationGM 2016-UP wd 3.5 Stamped Steel & Aluminum LCA Knuckle Lift Kit
921121300B *12130BAG4* 12130BAG4 GM 2016-UP 1500 4wd 3.5 Stamped Steel & Aluminum LCA Knuckle Lift Kit Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified
More informationOwner smanual. Banks torquetube System. Jeep 4.0L I-6 models including: Wrangler Cherokee Grand Cherokee Comanche
Owner smanual with Installation Instructions Banks torquetube System Jeep 4.0L I-6 models including: 91-99 Wrangler 91-99 Cherokee 93-98 Grand Cherokee 91-92 Comanche THIS MANUAL IS FOR USE WITH SYSTEM
More information2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware
Owner s Manual Model: Polaris RZR * 2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CD CHANGER ATTACHMENT KIT 2004 CR-V AII 26118 Issue Date SEP 2003 PARTS LIST CD Changer Attachment Kit (sold separately): P/N 08B26-S9A-100
More informationREVi RX-8 Intake. RX-8 REVi Intake System I PN Installation Instructions. Tools Required:
RX-8 REVi Intake System PN 18299 Installation Instructions I-18299 Tools Required: Small/Stubby Phillips head screwdriver Small flat head screwdriver Medium Phillips head screwdriver 10mm socket and ratchet
More informationWARNING. Important Notice
CAL (Color AquaLuminator ) Light and Return Water Flow for Above Ground Pools Owners Manual IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents SECTION
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS ULTIMATE BULL BAR APPLICATION: 2003-2014 Ford Expedition 2007-2014 Ford Expedition EL 2003-2014 Lincoln Navigator L 2/4WD 2009-2014 Ford F-150 2015-2017 Ford
More information