SED2-BT300-XX-C09 Migration Kits. Product Numbers

Transcription

1 Document No SED2-BT300-XX-C09 Migration Kits Product Numbers SED2-BT300-AB-C09 Migration Kit, SED2 FSAB 09 to BT300 FS4 * 208 Vac: Up to 3 hp 480 Vac: Up to 5 hp SED2-BT300-C4-C09 Migration Kit, SED2 FSC 09 to BT300 FS4 * 208 Vac: 7.5 hp SED2-BT300-C5-C09 Migration Kit, SED2 FSC 09 to BT300 FS5 * 208 Vac: 4 hp to 10 hp 480 Vac: 10 hp to 20 hp 600 Vac: Up to 10 hp SED2-BT300-D6-C09 Migration Kit, SED2 FSD 09 to BT300 FS6 * 208 Vac: 15 hp to 20 hp 480 Vac: 25 hp to 40 hp 600 Vac: 25 hp to 30 hp SED2-BT300-D7-C09 Migration Kit, SED2 FSD 09 to BT300 FS7 * 208 Vac: 25 hp 600 Vac: 40 hp Product Description This kit contains the parts needed to reconfigure an existing SED2 Bypass installation with a unit manufactured prior to September 2009 to a BT300 HVAC Drive with Bypass. Kit Contents Drive Adaptor Plate Hardware Kit Conduit Fittings Conduit Cable Ties Labels SED2-BT300-E7-C09 Migration Kit, SED2 FSE 09 to BT300 FS7 * 208 Vac: 30 hp to 40 hp 480 Vac: 50 hp to 60 hp 600 Vac: 50 hp to 60 hp * Manufactured prior to September 2009 Warning/Caution Notations WARNING: CAUTION: Personal injury or loss of life may occur if you do not follow the procedures as specified. Equipment damage or loss of data may occur if you do not follow the procedures as specified. Item Number , Rev.CA Siemens Industries, Inc.

2 Required Tools Small and large flat-blade screwdriver No. 1 and No. 2 Phillips screwdriver Wire cutter Wire stripper Utility knife T20 Torx 4 mm hex key 3/16 hex key 13 mm socket Nut driver 1/4 socket wrench 5/16 socket wrench 3/8 socket wrench Adjustable wrench Pliers or channel lock wrench 2. Remove the SED2 gland cover (Frame Size A only). Figure 1. Gland Cover Removed. 3. Remove the SED2 Drive terminal cover. Expected Installation Time 90 minutes Prerequisites WARNING: Disconnect all power before beginning installation. Read these in their entirety prior to beginning installation. Read the SED2 to BT300 Migration Guide ( ) prior to beginning installation. All wiring must conform to national and local codes and regulations (NEC, CE, and so on). Removing the SED2 Drive These SED2 to BT300 Bypass migration instructions encompass all versions of BT300 VFD replacement on units produced prior to September This includes sections for SED2 Frame Sizes A and B, Frame Size C, and Frame Sizes D and E Bypass equipment. Select the VFD removal and wiring for your appropriate migration package. Figure 2. Drive Terminal Cover Removed. 4. Using a small flat-blade screwdriver, disconnect the control wiring from the drive. 5. Remove the keypad and I/O board (Frame Size A only). SED2 Frame Sizes A and B Page 2 of 10 WARNING: 1. Disconnect power. Always wait five minutes after disconnecting the SED2 from the power source before performing any work. Figure 3. Keypad and I/O Board Removal. Siemens Industry, Inc.

3 6. Using a small Phillips screwdriver, disconnect the input power, output motor leads, and ground conductor at the SED2 Drive terminals. 7. Open the bypass door and pull the wiring down through the conduits into the cabinet. 8. Remove the conduit nuts from the fittings inside the bypass enclosure. Figure 6. Conduit Lock Nuts (Typical). 9. Using a No. 2 Phillips screwdriver, remove the drive mounting screws. Figure 4. Power and Motor Leads Removed (Frame Size A). Figure 7. Screw Removal (Frame Size A). Figure 5. Power and Motor Leads Removed (Frame Size B). Figure 8. Drive Removal (Frame Size B). 10. Pull the drive and conduits outward and up away from the enclosure back plane. The SED2 Drive removal is now complete. Siemens Industries, Inc. Page 3 of 10

4 SED2 Frame Size C WARNING: Always wait five minutes after disconnecting the SED2 from the power source before performing any work. 6. Remove the conduits nuts from the fittings inside the bypass enclosure. 1. Disconnect power. 2. Remove SED2 terminal strip and drive protective cover. Figure 3. Conduit Lock Nuts (Typical). 7. Using a No. 2 Phillips screwdriver, remove the drive mounting screws. Figure 1. SED2 Drive with Covers Removed. 3. Using a small flat-blade screwdriver, disconnect the control wiring from the drive. 4. Using a small Phillips screwdriver, disconnect the input power, output motor leads, and ground conductor at the SED2 Drive terminals. 5. Open thebypass door and pull the wiring down through the conduits into the cabinet. Figure 4. SED2 Drive Mounting Screw Location. 8. Pull the drive and conduits outward and up away from the enclosure back plate. 9. SED2 Drive removal is complete SED2 Frame Sizes D and E WARNING: Always wait five minutes after disconnecting the SED2 from the power source before performing any work. 1. Disconnect power. 2. Remove keypad. Figure 2. Control, Power, and Motor Wiring Removed. Page 4 of 10 Siemens Industry, Inc.

5 Figure 1. Removal of SED2 Keypad. 3. Using a T20 Torx, remove the right side cover and bottom cover from the SED2 Drive. Figure 4. Control Wiring Removed. 5. Using a 13 mm socket, disconnect the input power, output motor leads, and ground conductor at the SED2 Drive terminals. Figure 2. Drive Right Side Cover. Figure 3. Drive Bottom Cover. 4. Using a small flat-blade screwdriver, disconnect the control wiring from the drive. Figure 5. Power, Motor, and Ground Wire Removed. 6. Open the bypass door and pull the wiring down through the conduits into the cabinet. 7. Remove the conduits nuts from the fittings inside the bypass enclosure. Figure 6. Conduit Lock Nuts (Typical). 8. Using a No. 2 Phillips screwdriver, remove the drive mounting screws. The SED2 Drive removal is now complete. Siemens Industries, Inc. Page 5 of 10

6 Installing the BT300 Drive 1. Using four each of the mounting hardware screws, lock washers, and flat washers as required, place the drive adapter plate in place on the back plane and secure. Table 1. Back Plate and Hardware. SED2 Enclosure Drive Back Plate No. Screw Set Detail AB FS #10-32 NF A C FS #10-32 NF A C FS #10-32 NF A D FS /4-20 NC B D FS /4-20 NC C E FS /4-20 NC C Figure 9. Figure 1. Back Plate Reference Drawing. Page 6 of 10 Siemens Industry, Inc.

7 3. Remove the cable protection plate from the front of the BT300 Drive. Figure 4. Cable Protection Plate Removed. 4. Remove the cable gland bottom plate from the BT300 drive. Figure 2. Drive Mounting Plate. 2. Loosen the four screws corner screws and remove the cover from the BT300 Drive. Figure 5. Drive Gland Plate. 5. Install the required conduit fittings, sealing washers, and secure the lock rings into the top of the bypass enclosure and the BT300 gland plate. Figure 3. Drive Cover Removal. Figure 6. Conduit Fitting Installation (Typical). Siemens Industries, Inc. Page 7 of 10

8 Figure 7. Conduit Fitting Installation (Typical). 6. Hang the BT300 Drive in place on the drive adaptor plate. Use two of the hex nuts at the top studs to hold the drive in place. Figure 10. Complete the Drive Installation. Installation of the BT300 Drive is now complete. Figure 8. Drive Installation, Step Maneuver the gland plate in place while positioning the drive in its final location. Figure 9. Gland Plate Re-Installation. 8. Reattach the gland plate using the screws removed in installation Step 4. Remove the hex nuts at the top of the drive adaptor plate and using the remaining hex nuts, lock washers and, and washers, secure the BT300 Drive in place. Page 8 of 10 Siemens Industry, Inc.

9 Wiring the BT300 Drive 1. Run the existing wires from thebypass enclosure back up through the conduit and into the bottom of the BT300 Drive. Figure 2. Re-Install the Protective Cover. 4. Connect the control wiring to the appropriate terminals as shown in Table 1. Figure 1. BT300 Drive Power and Motor Connections. 2. Trim and strip the wires as needed. Terminate the input, output power wires, and the ground to the BT300 Drive. NOTE: If wires are not long enough, replace with only the same Type and size. 3. Reinstall the cable protection plate using the screws that were removed in installation Step 3. Figure 3. BT300 Drive Control Wiring. 5. Use cable ties to secure the control wiring to the cable protection plate. SED2 Terminal No. Description Bypass Wire Color (Number) Conventional (A) BT300 Terminal No. Description Function 8 Digital Input Digital Input 2 Run Interlock 2 (M2 Status Coast to Stop) 5 Digital Input Digital Input 1 Start Stop 9 24Vdc Vdc + Power 24 Vdc 22 RO1 NO 7 24 RO2 NC Fault Status 21 RO1 Common 5 25 RO2 Common Fault Status Siemens Industries, Inc. Page 9 of 10

10 Completing the Installation 1. Using a utility knife or pliers, cut free the opening on the drive cover to clear the control wiring conduit. 3. Remove the existing bypass labels on the inside of the bypass cabinet door and replace with new labels provided in the Migration Kit. 4. Close the bypass enclosure door and secure. 5. Reconnect power. Bypass Parameter Settings Figure 1. Trim Cover to Match Conduit. 2. Mount the BT300 Drive cover and tighten the screws. 1. Change Ctrl Signal 2 A ( ) to a value of DigIN Slot0.1 (virtual off). This removes the reverse command from DI2. 2. Change Run Interlock 2 ( ) to a value of DigIN SlotA.2 (use Digital Input 2). This is used to monitor the M2 Contactor. 3. Change RO2 Function ( ) to a value of FaultInvert. This is for fail-safe operation of fault relay (wired to normally closed contact). If the inverter loses power but the bypass does not, then the contact closes to indicate to the bypass that there is a problem. The installation is now complete. See the SED2 to BT300 Migration Guide ( ) for further information. Figure 2. BT300 Drive Cover Re-Installed. Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as design improvements are introduced. Product or company names mentioned herein may be the trademarks of their respective owners Siemens Industry, Inc. Siemens Industry, Inc. Building Technologies Division 1000 Deerfield Parkway Buffalo Grove, IL Your feedback is important to us. If you have comments about this document, please send them to sbt_technical.editor.us.sbt@siemens.com Document No Printed in the USA Page 10 of 10