Dodge Charger
|
|
- Margaret Mitchell
- 5 years ago
- Views:
Transcription
1 LAW ENFORCEMENT VEHICLE EQUIPMENT 2926 Yelm Hwy SE - Olympia, WA PH (360) TF FAX (360) Replacement Seat/ CAREFULLY READ INSTRUCTIONS BEFORE BEGINNING INSTALLATION. #12 PARTITION ALWAYS CHECK PARTS LIST FOR FUEL LINES, BRAKE LINES, WIRING OR ANY OBSTRUCTIONS BEFORE DRILLING ANY HOLES! TO AVOID TAMPERING WITH FASTENERS ALWAYS PLACE WASHER AND NUTS AWAY FROM THE GUARDED AREA!!! INSTALL THE SETINA SEAT PRIOR TO INSTALLING THE PARTITION. NOTE: SEAT BELT RETRACTORS ARE EQUIPPED WITH AN ORANGE/RED STOP FORK. DO NOT REMOVE UNTIL BELT IS FULLY INSTALLED. IF REMOVED DO NOT ALLOW BELT TO RETRACT PAST THAT POINT. REPLACEMENT SEAT PARTS LIST RETRACTOR ASSEMBLY ITEM QTY PART # DESCRIPTION 8 ITEM QTY PART # DESCRIPTION 1 1 SP11631 Setina Replacement Seat 2 1 SP8834 Lower Seat Belt Port - Cover 3 2 SP8857 End Release Partition - Buckle 4 2 SP8965 Rear Seat - Upper Seat Belt Port - Cover 5 1 SP9124 Lower Cover Bracket 6 2 SP12423 Twin Wire Seat Buckle 7 1 SPW11627 Lower Bracket - Weldment 8 1 SP9123 Rear Deck Cover /16 x 1 Bolt (not pictured) /16-20 x 1.5 Bolt (not pictured) /4 USS Fender Washer (not pictured) /16 Washer SEA Hard YZ (not pictured) /16-18 x 1 1/4 BHSCS (not pictured) /16 Nylock (not pictured) /16 Nylock (not pictured) 16 2 SP13043 Seat Retractor 17 2 SP9142 Center Retractor Stud - Strap Bracket 18 3 SP9143 Rear Deck Bracket - Washer Plate 19 1 SP9162 Pinch Weld Backing Plate 20 1 SPW9147 Upper Retractor Mount Bracket - Weldment PAGE 1
2 Replacement Seat/ IMPORTANT: BOLT BAG MAY CONTAIN EXTRA FASTENERS BOLT BAG BB9175 ITEM QTY PART # DESCRIPTION _16-20 x 1.5 Bolt PB Outer Spacer /4 Dome Cap /4 Wizlock mm x 1.25mm Hex Flg Nut C125KTCYO/ON PIN 1/4 x 1.25 THSCS /16 Nylock #6 x.75 Phillips Pan Head SMS /4 x 1 Phillips SMS C75KTCYO-NO PIN 1/4 x 3/4 THSCS /16 Washer SEA Hard YZ /4 Panel Retainer /4 Fender Washer PAGE 2
3 Replacement Seat/ Figure 1 STEP 1 Figure 2 STEP 2 SEAT BELT GUIDE PRY BAR FOR SEAT CLIP STEP 1 - Instructions Begin by removing the rear seat, back rest and rear deck cover from the vehicle, use a piece of flat bar that is 7 to eject the clips on the back rest). Repeat for passenger side. Remove the lower factory seat belt buckles. SEE FIGURE #1 STEP 2 - Instructions Remove the C pillar cover from the vehicle, (the seat belt guide will need to be notched and removed in order to free the belt form the C pillar). Repeat for passenger side. SEE FIGURE #2 Figure 3 STEP 3 Figure 4 STEP 4 CENTER FACTORY RETRACTOR ZIP TIED FACTORY SEAT BELT REAR DECK MOUNT HOLES 2 OF 3 STEP 3 - Instructions Roll and zip tie the factor seat belts in place. See Figure #3. Return the C pillar cover. Repeat for passenger side. SEE FIGURE #3 STEP 4 - Instructions Remove and store the factory center retractor from the vehicle. Drill out the (3) existing mount holes on the rear deck located behind child anchors using a 7/16 drill bit. Repeat for passenger side. SEE FIGURE #4 PAGE 3
4 Replacement Seat/ Figure 5 STEP 5 Figure 6 STEP 6 RETRACTOR ASSEMBLY STRAP BRACKET RETRACTOR BRACKET WASHER PLATES STEP 5 - Instructions Remove the (3) washer plates from the center retractor assembly. Rotate the strap bracket & place over the factory center retractor stud. NOTE: Tighten the 7/16 fasteners at this time. SEE FIGURE #5 STEP 6 - Instructions Secure the retractor mount bracket weldment and washer plates to the rear deck using the provided 7/16 x 1.5 bolts, 7/16 washer (on both sides) and 7/16 nyloc nuts. SEE FIGURE #6 Figure 7 STEP 7 Figure 8 STEP 8 PINCH WELD W/BACKING PLATE CHILD SEAT ANCHOR POINTS STEP 7 - Instructions Move to the lower portion where the retractor bracket meets the pinch weld. Drill the (2) mount points using 21/64 drill bit. Place the backing plate on the backside. Secure using the provided 5/16 x 1.25 bolt, 1/4 USS fender washer (on both sides) and 5/16 nyloc nuts. Return the backrest to the vehicle. SEE FIGURE #7 STEP 8 - Instructions Using a pry bar bend the (6) lower child seat anchor points up out of the away. SEE FIGURE #8 PAGE 4
5 Replacement Seat/ Figure 9 STEP 9 Figure 10 STEP 10 LOWER COVER BRACKET LOWER SEAT MOUNTING BRACKET ROCKER MOLDING STEP 9 - Instructions STEP 10 - Instructions Secure the lower cover bracket to the riv nuts on the seat belt mount bracket weldment using the provided 1/4 x 3/4 bolts. Place the lower bracket weldment over the existing studs and secure with the existing fasteners. SEE FIGURE #9 Notch the rocker molding as shown in figure #18. NOTE: Make adjustments as needed to fit around the seat and buckle. SEE FIGURE #10 Figure 11 STEP 11 Figure 12 STEP 12.5 SPACER BUCKLE STEP 11 - Instructions Place the 1/2 spacer between the lower buckle and the vehicle s sheet metal. Secure to the factory mount point using a 7/16 x 1.5 fastener with washer. Repeat for passenger side. SEE FIGURE #11 STEP 12 - Instructions Using a tie down, synch the Setina seat and move it into the vehicle. SEE FIGURE #12 PAGE 5
6 Replacement Seat/ Figure 13 STEP 13 Figure 14 STEP 14 FEED SEAT BELTS THROUGH OPENINGS STEP 13 - Instructions Before removing the tie down, thread the retractor seat belts through the upper port openings. SEE FIGURE #13 STEP 14 - Instructions Insert the buckle through the hole on the side of the seat. Adjust the seat into place. SEE FIGURE #14 Figure 15 STEP 15 Figure 16 STEP 16 LOWER COVER LOWER PHILLIPS SMS STEP 15 - Instructions Adjust the seat so the rear deck portion slides over the existing studs. Secure the seat loosely to the rear deck using the 8mm x 1.25 Hex Flange nut. Repeat for passenger side. SEE FIGURE #15 STEP 16 - Instructions Secure the seat belt end to the studs on the lower bracket weldment, using the 7/16 nyloc and 7/16 washer. NOTE: The socket will get stuck. Use channel locks to pull it out. SEE FIGURE #16 PAGE 6
7 Replacement Seat/ Figure 17 STEP 17 Figure 18 STEP 18 STEP 17 - Instructions Place the lower cover over the lower port opening and secure using the provided 1/4 x 1.25 bolt with 1/4 fender washer. SEE FIGURE #17 LOWER COVER UPPER PORT COVERS STEP 18 - Instructions Slide the seat belt through the upper port covers. Repeat for passenger side. NOTE: Driver side shown. SEE FIGURE #18 Figure 19 STEP 19 Figure 20 STEP 20 #6 X 3/4 SMS LOWER PHILLIPS SMS STEP 19 - Instructions Secure the port covers to Setina seat using #6 x 3/4 SMS SEE FIGURE #19 STEP 20 - Instructions Move to the lower portion of the seat. Drill the (4) mounting points into the vehicle using a 7/32 drill bit. Secure using the provided 1/4 x 1 Phillips SMS w/1/4 fender Washers. Repeat for passenger side. NOTE: Driver side shown. SEE FIGURE #20 PAGE 7
8 Replacement Seat/ Figure 21 STEP 21 Figure 22 STEP 22 TPO REAR DECK COVER PARKING BUCKLE STEP 21 - Instructions Set the TPO rear deck cover into place. Align the obrounds on the deck cover to the holes on the rear edge of the seat. Secure deck to the seat using the 1/4 black plugs. SEE FIGURE #21 STEP 22 - Instructions Align the parking buckle to the lower mounting hole on the mount plate. Secure using the provided 1/4 x 3/4 fastener, 1/4 fender washer (on both sides) and 1/4 wizlocks. Place dome caps over wizlocks. NOTE: Driver side shown. SEE FIGURE #22 Figure 23 STEP 23 COMPLETE INSTALL STEP 23 - Instructions Tighten all fasteners to complete the install. SEE FIGURE #23 PAGE 8
Dodge Charger
LAW ENFORCEMENT VEHICLE EQUIPMENT 2926 Yelm Hwy SE - Olympia, WA 98501 PH (360) 491-6197 TF 1-800-426-2627 FAX (360) 459-0729 Cover Seat/ CAREFULLY READ INSTRUCTIONS BEFORE BEGINNING INSTALLATION. #12
More informationChevy Tahoe. Replacement Seat/ Chevy Tahoe Installation Instructions. Questions? us at
LAW ENFORCEMENT VEHICLE EQUIPMENT 2926 Yelm Hwy SE - Olympia, WA 98501 PH (360) 491-6197 TF 1-800-426-2627 FAX (360) 459-0729 Replacement Seat/2015-2018 Chevy Tahoe CAREFULLY READ INSTRUCTIONS BEFORE BEGINNING
More informationINSTALLATION MANUAL FORD PI SEDAN PRISONER TRANSPORT SEAT WITH OS-BELT SEATBELTS (PI02) Required Tools:
INSTALLATION MANUAL FORD PI SEDAN PRISONER TRANSPORT SEAT WITH OS-BELT SEATBELTS (PI02) Required Tools: Drill Bits: 9/16 (.5625 ) Power Drill Socket Wrench Set Square #2 Driver Rubber Mallet Utility Knife
More informationK9-F17 INSTALLATION INSTRUCTIONS K9 Kit for FORD INTERCEPTOR SEDAN
K9-F17 INSTALLATION INSTRUCTIONS K9 Kit for 2013-2018 FORD INTERCEPTOR SEDAN TOOLS Needed: Phillips Screw Driver Trim panel removal tools Caulk Gun Standard Socket set Metric Socket set Wire Cutters /Crimpers
More informationRef Qty Part Description Part Number -1- Kit ( ) Contents:
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationENCORE 52" X-TREME. 2-BAG GRASS CATCHER for units w/ S/N and above ASSEMBLY AND PARTS DIAGRAMS
ENCORE 52" X-TREME 2-BAG GRASS CATCHER for units w/ S/N 53138 and above ASSEMBLY AND PARTS DIAGRAMS Notes: ASSEMBLY INSTRUCTION Figure 1 Using 1/2" wrench, remove the discharge cover and the RH deck belt
More informationP/N Rev 01 04/14-1- NOTE: If you are ordering hinges for your rear doors, order and/or
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationJEEP CHEROKEE, WAGONEER (XJ) FRONT BUMPER INSTALLATION INSTRUCTIONS KIT# W/ WINCH KIT# 83203
3651 N Highway 89 Chino Valley, AZ 86323 (928) 636-7080 www.p-a-g.net JEEP CHEROKEE, WAGONEER (XJ) FRONT BUMPER INSTALLATION INSTRUCTIONS 1984-2001 KIT# 83202 1984-2001 W/ WINCH KIT# 83203 WARNING Before
More informationWildcat System Instructions
Wildcat System Instructions NOTE: Most steps contained in these instructions will need to be repeated on the other side of the vehicle. Prior to assembly of windshield it is necessary to establish what
More informationGrass Catcher. Instructional / Parts Manual Part Number: January ( & ) & Drive Kits ( , , )
Grass Catcher Instructional / Parts Manual Part Number: January 200 5020 ( 507 & 5026 ) & Drive Kits ( 52030, 5203, 52032) Table of Contents Z RIDER GRASS CATCHER TWO PACKAGED ITEMS LIST 507 BLOWER ASSEMBLY
More informationLevel of Difficulty Easy. Product Image. Front Mounting Bracket (553204) AC Mounting Bracket (553211) Tools Required Socket, 1/2"
INSTALLATION MANUAL Parts List 3 2 1 1 1 3 2 4 13 16 13 16 2 2 14 Front Mounting Bracket Middle Mounting Bracket Rear Mounting Bracket AC Mounting Bracket AC Top Mounting Bracket U-Bolt 3" U-Bolt 3.75"
More informationHiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com HiBoy Maverick/Commander Doors Part # 07-2001 HiBoy4 Maverick/Commander Doors Black Congratulations on your
More informationMOUNT BRACKET PARTS and HARDWARE: Installation parts with * come loose in hardware kit bag. Other parts are preassembled
INSTALL INSTRUCTIONS C-DMM-2006 Dash Monitor Mount 2017-2019 F-250, 350, 450 Pickup, F-450 and 550 Cab Chassis, 2015-2019 Ford F-150 and 2018-2019 Expedition Notes: 1. The C-DMM-2000 series Dash Monitor
More informationINSTALLATION INSTRUCTIONS DRAWERS #240
INSTALLATION INSTRUCTIONS DRAWERS #240 Please read and fill out the enclosed warranty registration card to activate your warranty. SHIPMENT CONTENTS #1 Lid #2 Rear #3 Left side panel #4 Right side panel
More informationClassic Light Bar Mustang
Classic Light Bar 2005-2012 Mustang Note: Read installation instructions before starting. Component List: 1 Light Bar Part #110000 1 Driver Side Bracket w/set Screw Part #115003 1 Passenger Side Bracket
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 2011 Dodge Charger Road Defender 5000 Series Push Bumper Part Number 5076 Do not attempt to install this product on any vehicle other than the one it is designed for and listed
More informationSafeGuard Flex Seat Maintenance Guide
SafeGuard Flex Seat Maintenance Guide 1) Preparation For Removal And Replacement Of Seat Back Covers And Retractor Assemblies a) Unlatch seat cushion and pivot cushion up and forward. b) Separate seat
More informationK9-C23 INSTALLATION INSTRUCTIONS K9 Kit for CHEVY TAHOE PPV (9C1)
K9-C23 INSTALLATION INSTRUCTIONS K9 Kit for 2015-2018 CHEVY TAHOE PPV (9C1) TOOLS Needed: Phillips Screw Driver Trim panel removal tool Caulk Gun Standard Socket set Wire Cutters /Crimpers Drill & Drill
More information2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill 1-3/4" Hole saw 2" Hole saw
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill
More informationINSTRUCTIONS INSTRUCCIONES CONSIGNES
AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: 2013-UP FORD ESCAPE APP PART # 28-21010, 28-21015 STYLIZED RUNNING BOARD ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 2 RUNNING BOARDS
More information2005+ Drag Race Roll Bar (Mm5RB-20)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 2005+ Drag Race Roll Bar (Mm5RB-20) Note that the NHRA DOES allow the door bars
More informationLONGTRAVEL SUSPENSION FOR CLUB CAR Model
INSTALLATION INSTRUCTIONS LONGTRAVEL SUSPENSION FOR CLUB CAR 1980 2003 Model C-7-06 TABLE OF CONTENTS Progressive Suspension Kit... 2 Kit Contents...3-6 Disassembly...7-17 Assembly...18-29 Rack & Pinion
More informationCENTER BELT SYSTEM INSTALLATION INSTRUCTIONS CARCG121220
CENTER BELT SYSTEM INSTALLATION INSTRUCTIONS 2013+ DODGE CHARGER Distributed by CARCG121220 Important Notice: Read all instructions before starting the installation of the seat. Before drilling or installing
More informationCHROME SADDLEBAG SUPPORTS KIT VT750C2B P/N 08L56-MEG-100J. Honda Dealer: Please give a copy of these instructions to your customer.
PARTS LIST Accessory Application Publications No. CHROME SADDLEBAG MII 12987 INSTALLATION SUPPORTS KIT Issue Date P/N 08L56-MEG-100J INSTRUCTIONS September 2009 Honda Dealer: Please give a copy of these
More information460 HORIZON DR. SUITE 100 SUWANEE, GA PHONE: FAX: Renegade 3 Sidebar.
Page 1/5 Part #11591.11 6 7 10 5 9 8 4 8 7 3 2 1 1. Driver/Left Sidebar (1) 2. Passenger/Right Sidebar (1) 3. Driver/Left Mounting Bracket (1) 4. Passenger/Right Mounting Bracket (1) 5. Driver/Left Mounting
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL V5008 Kubota RTV 72 Snow Blade The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation is complete. IMPORTANT: Please
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD DODGE CHARGER 06-08
INSTALLATION INSTRUCTIONS GRILLE GUARD DODGE CHARGER 06-08 FIGURE #3 SECTION #2 INSTALL THE BRACKETS STEP #1: Locate the 8 holes in the inner bumper (4 on ea~h ~ide). Use a 13 mm socket on a 6" extension
More information2. FOLLOW THE INSTRUCTIONS INCLUDED WITH THE SPECIFIC BRACKET PACKAGE THAT YOU ARE USING, TO MOUNT THE BRACKETS TO YOUR VEHICLE.
INSTALLATION INSTRUCTIONS AND PARTS LIST MODEL: 583098, 583102, 583108, 583114, 583125, 584098, 584102, 584114, 584125 O-MEGA II 6 OVAL STEPS UNIVERSAL APPLICATION 1. READ INSTRUCTIONS COMPLETELY AND CHECK
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publication No. WINCH MOUNT P/N 08L74-HR3-A20 After 13 TRX420 (All except TRX420FA/FPA) After 13 TRX500 (All except TRX500FA/FPA) MII 15067 Issue Date Revised:
More informationINSTALLATION INSTRUCTIONS AND PARTS LIST APPLICATION: MODEL /33/36 (STAINLESS STEEL) SIDE ENTRY STEP BOARDS: BODY MOUNT APPLICATION
INSTALLATION INSTRUCTIONS AND PARTS LIST APPLICATION: MODEL 481032/33/36 (STAINLESS STEEL) SIDE ENTRY STEP BOARDS: BODY MOUNT APPLICATION 1. READ INSTRUCTIONS COMPLETELY AND CHECK TO MAKE SURE THAT ALL
More informationInstallation, Operating Instructions and Replacement Parts Installation video available at
Installation, Operating Instructions and Replacement Parts Installation video available at www.kool-shield.com/support/ Made in the USA By Humboldt Specialty Manufacturing Co. www.kool-shield.com Revision
More informationINSTALLATION INSTRUCTIONS DODGE DAKOTA 2 KIT # 682 (2WD), 692 (4WD) 3 KIT # 683 (2WD), 693 (4WD)
INSTALLATION INSTRUCTIONS 1997-1999 DODGE DAKOTA 2 KIT # 682 (2WD), 692 (4WD) 3 KIT # 683 (2WD), 693 (4WD) Installation of a Performance Accessories body lift kit will change the vehicle s center of gravity
More informationMarlon Xplore / Xplore Pro Deck Installation & Assembly Instructions
Marlon Xplore / Xplore Pro Deck Installation & Assembly Instructions Marlon Recreational Products www.marlonproducts.com 1-800-663-7367 INSTALLATION INSTRUCTIONS: 1. Remove the ramp from underneath the
More informationSECOND ROW SEAT BELT SECOND ROW SEAT BELT. Second Row Seat Belt SB-13 EXPLODED VIEW SEAT BELT RETRACTOR < REMOVAL AND INSTALLATION >
SECOND ROW SEAT BELT Second Row Seat Belt EXPLODED VIEW SECOND ROW SEAT BELT INFOID:0000000012551454 A B C D E F G SB I J K L M N O AWHIA0861ZZ P 1. Seat belt height adjuster (LH/RH) 2. Seat belt retractor
More informationI. Before starting installation
5. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. A. Disconnect battery cables 1. Disconnect the negative cable first, then the
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-049 Cab Enclosure MULE SX 3-4 Hours WARNING Improper installation of this accessory could result in an accident causing serious
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS PARTS LIST: 1 32-inch Steel Running Board 1 8-1.25mm x 35mm Hex Bolt 1 96-inch Steel Running Board 13 8-1.25mm x 25mm Hex Bolt 5 Passenger Side/Driver Side Mounting Brackets 20
More informationPHASE 3 POWERSPORTS AUDIO KIT MAVERICK X3 CAN-AM. pg 3 Disassembly, Wire and Amplifier Plate Installation. pg 11 Dash Kit Installation
CAN-AM MAVERICK X3 PHASE 3 POWERSPORTS AUDIO KIT pg 3 Disassembly, Wire and Amplifier Plate Installation pg 11 Dash Kit Installation pg 15 Underseat Subwoofer Installation pg 19 Dash Speaker Pods Installation
More informationLexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2013-15 Lexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements Part #1372-0102-13 / Black Ice
More informationVan Rack Installation Manual Ford Transit Connect
1.888.772.8400 Big to small... We do it all Van Rack Installation Manual Ford Transit Connect Thank you for your purchase of an Unruh Fab Van rack. We have designed and built this rack so that you can
More informationtable of Contents Warranty:
table of Contents placement of the Mounting Bolts spudnik swingout... 2 spudnik solid... 2 logan swingout... 3 logan solid... 3 double l swingout... 4 double l solid... 4 Mounting Framework... 5-6 Mounting
More informationBLACK BEAR ZTR. Parts Manual. English
BLACK BEAR ZTR Parts Manual KOHLER / 9999 KAWASAKI / 99999 KOHLER / 9999 KOHLER / 9999 KAWASAKI / 9999 KAWASAKI / 999990 KAWASAKI / 99997 Please read the operator s manual carefully and make sure you understand
More informationCHEVY/GMC /2-TON PICKUP 3 BODY LIFT INSTALLATION INSTRUCTIONS 2006 KIT# PA10163 MANUAL TRANSMISSION VEHICLES REQUIRE KIT# PA4701
3651 N Highway 89 Chino Valley, AZ 86323 (928) 636-7080 www.p-a-g.net CHEVY/GMC 1500 1/2-TON PICKUP 3 BODY LIFT INSTALLATION INSTRUCTIONS 2006 KIT# PA10163 MANUAL TRANSMISSION VEHICLES REQUIRE KIT# PA4701
More informationINSTALLATION PROCEDURE, HHT WITH BULKHEAD. Vehicle prep
INSTALLATION PROCEDURE, HHT WITH BULKHEAD Vehicle prep Notice where the top will interface with the vehicle. The bulb seal on the front of the hard top will rest on the windshield frame. The doorposts
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationFRONT FENDERS WITH FACTORY INNER FENDERS JEEP WRANGLER TJ/LJ/YJ/CJ7 INSTALLATION INSTRUCTIONS
FRONT FENDERS WITH FACTORY INNER FENDERS JEEP WRANGLER TJ/LJ/YJ/CJ7 INSTALLATION INSTRUCTIONS TOOLS NEEDED 13mm socket 5/32 Allen head 5/16 wrench or socket 7/16 wrench or socket 7/32 Allen head 5/8 wrench
More informationINSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter
INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter TOOLS REQUIRED: Phillips Screw Driver T-20 Torx bit Standard Socket set 9/64 Allen wrench
More informationInstallation instruction do88 Intercooler for SAAB 9-3SS/SC 2,8 V6 Turbo
Installation instruction do88 Intercooler for SAAB 9-3SS/SC 2,8 V6 Turbo This instruction shows how to replace the OEM intercooler with this performance intercooler. At this type of installation we always
More informationParts Manual EZF 3417/ Please read the operator s manual carefully and make sure you understand the instructions before using the machine.
Parts Manual EZF 3417/ 96579301 Please read the operator s manual carefully and make sure you understand the instructions before using the machine. English 200 HTC. All Rights Reserved. Beatrice, NE. Printed
More informationSECTION 1 SEAT BACK SUPPORT INSTALLATION
TM REAR SEAT KIT IMPORTANT: Do not fully tighten hardware until instructed. Read through all instructions before beginning installation. PATRIOT SEAT INSTALLATION TABLE OF CONTENTS: Section 1 - Seat Back
More information2 Rubber Bumper GSM MM nut GSM30201 K9-F18-PT_INST_4-16
K9-F18-PT INSTALLATION INSTRUCTIONS K9 Kit for 2013-2019 FORD INTERCEPTOR UTILITY Vehicle Notes: 1. For K9 applications, it is recommended to order the Interceptor Utility with the OEM optional Aux Rear
More information2015+ S550 MUSTANG Battery Relocation Kit WR-BTRYRELOKIT-LH WR-BTRYRELOKIT-RH
2015+ S550 MUSTANG Battery Relocation Kit WR-BTRYRELOKIT-LH WR-BTRYRELOKIT-RH The Watson Racing Battery Relocation Kit is NOT designed to protect you in the case of an accident, and therefore is INTENDED
More information92-00 Civic/ Integra/ Del Sol/ Accord/ CRX
92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 90-97 Accord/ 92-95 CRX Front Kit Part No. 75440 www.airliftperformance.com Please read these instructions completely before proceeding with installation MN-513
More informationThe Go Baby Go Build Manual
The Go Baby Go Build Manual The step-by-step guide to creating your own Go Baby Go Car 4488 Shockwave Robotics and Pacific University Index 1. List of Mat erials 2. Mechanical Assembly a. Installing the
More informationINSTALLATION GUIDE P1000 PRO-CELL CURRENT FORD POLICE UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE P1000 PRO-CELL 2013 - CURRENT FORD POLICE UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD PARTITION SYSTEM WB4711-01D WB4711-01P 4K47UINTPRO
More informationASSEMBLY & INSTALLATION INSTRUCTIONS
ASSEMBLY & INSTALLATION INSTRUCTIONS VEHICLE MOUNT KIT 99101087 AND VEHICLE CENTER MEMBER For 26 Series: 99100890 TO FIT 2009 & Later FORD F150 4x4 (without EcoBoost V6) 2011 & Later FORD F150 4x4 (with
More informationINSTALLATION INSTRUCTIONS FORD SUPER DUTY NOTE: (Vehicle Retains Tow Hook) PART # P3064
INSTALLATION INSTRUCTIONS 2011-14 FORD SUPER DUTY 250-550 NOTE: (Vehicle Retains Tow Hook) PART # P3064 PARTS LIST: Qty Description Qty Description 1 Grill Guard 2 10mm x mm Hex Bolts 1 Driver/Left Lower
More informationLAND ROVER DISCOVERY 3 ARB BULL BAR AND WINCH BAR WARNING
LAND ROVER DISCOVERY 3 ARB BULL BAR AND WINCH BAR PART No 3432150 DISCOVERY 3 WINCH BAR PART No 3232150 DISCOVERY 3 BULL BAR WARNING FOR VEHICLES EQUIPPED WITH SRS AIRBAG WHEN INSTALLED IN ACCORDANCE WITH
More informationPar ts Manual. Scissor Lifts. Installation Instructions. Pipe Cradle. Assembly, Installation & Operation. Serial Number Range
Par ts Manual Cradle Assembly, Installation & Operation Serial Number Range Scissor Lifts Part No. 72830GT Rev E Information Important Read, understand and obey the safety rules and all instructions before
More informationSUT-450-I ASSEMBLY REQUIREMENTS
SUT-450-I Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16,3/4,13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all T-bolt
More informationFOG LAMPS INSTALL KIT
FOG LAMPS INSTALL KIT PT CRUISER INSTALLATION INSTRUCTIONS Read entire instructions thoroughly before starting. For proper aiming of fog lamps, follow procedures in the service manual. NOTES: Left and
More informationINSTALLATION GUIDE P1000 PRO-CELL CURRENT FORD POLICE UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE P1000 PRO-CELL 2013 - CURRENT FORD POLICE UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD PARTITION SYSTEM WB4711-01D WB4711-01P 4K47UINTPRO
More informationLexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015-16 Lexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles Upper Insert - factory chrome surround and emblem reused
More information11221 INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 0-CURRENT MAKE: CHEVROLET MODEL: VOLT STYLE: SEDAN WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S
More informationKK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console)
KK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for 2011-2016 FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console) TOOLS Needed: Phillips Screw Driver Power Drill with Drill Bits Trim panel
More information3" Nerf Bars Installation Instructions. # Standard Cab. # Super Crew. # Super Cab
3" Nerf Bars Installation Instructions Part: # 203016/203039/203040 Ford F-150 2009-2010 Click To Select: # 203016 2009-2010 Standard Cab # 203039 2009-2010 Super Crew # 203040 2009-2010 Super Cab INSTALLATION
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Honda Dealer: Please give a copy of these instructions to your customer. PARTS LIST (15) (8) (12) (14) (13) (10) (11) (18) (17) (1) Accessory Application Publications No. TRX500FA/FGA
More informationSWING DOOR SOFT ENCLOSURE (part# 16733)
800-643-7332 americanlandmaster.com This kit is for use with all fullsize, 2 passenger ALM utility vehicles. SWING DOOR SOFT ENCLOSURE (part# 16733) NOTE TOOLS REQUIRED Drill 1/4 Drill Bit 7/16 Wrench
More informationSize Grade Torque 9/ ft/lbs. 5/ ft/lbs. 3/ ft/lbs. 7/ ft/lbs ft/lbs.
Ford 150 5 1/2, 6 1/2 & 8 Boxes 4/16 HJ32003,Rev 2 BOlT TORQUE SPECIFICATIONS STANDARD BOlTS: Size Grade Torque 5/16 5 20 ft/lbs. 3/8 5 35 ft/lbs. 7/16 5 56 ft/lbs. 1/2 5 85 ft/lbs. Size Grade Torque 9/16
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More informationInstallation instruction do88 Intercooler for SAAB 9-3SS/SC 4-cyl Turbo
Installation instruction do88 Intercooler for SAAB 9-3SS/SC 4-cyl Turbo This instruction shows how to replace the OEM intercooler with this performance intercooler. 1. 4. 5. At this type of installation
More informationInstallation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com Indianapolis, IN
More information<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W
B&W Trailer Hitches 6 Hawaii Rd / PO Box 86 Humboldt, KS 66748 P:60.473664 F:60.869.903 Turnoverball Gooseneck Hitch Installation Instructions MODEL 08
More informationMOUNTING INSTRUCTIONS JOHN DEERE GATOR NON-ROPS CAB
MOUNTING INSTRUCTIONS JOHN DEERE GATOR NON-ROPS CAB FITS 4X2 & 6X4 GATORS A-11112, A-11224, A-11225, A-11226 MANUFACTURED BY: BOX 70 LITCHFIELD, MINNESOTA 55355-0070 (320) 693-3221 Fax: (320) 693-7252
More informationCONVERSION FROM MANUAL PULL STRAP TO POWER AWNING
White Kit # Black Kit # Description 323948 323949 Conversion from Manual Pull Strap to Power Awning Kit Note: Parts below are available in kits referenced above or individually as needed. White Part #
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS 6 PREMIER AND 4 OVAL TUBE MOUNT KIT APPLICATION: 2009-2015 Dodge Ram 1500 Quad/Crew Cab 2010-2015 Dodge Ram 2500/3500 Crew Cab PART NUMBER: 22-1905 ITEM QUANTITY
More informationM944T. Soundshield Assembly Instructions
M944T Soundshield Assembly Instructions Corporate Headquarters 4420 14th Avenue N.W. Seattle, WA 98107 Tel: (206) 789-3880 Toll Free: (800) 762-0165 Fax: (206) 782-5455 Alaska Branch Offi ce 1200 West
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More informationInstallation Instructions Road Defender Push Bumper Part # L Ford Sedan Police Interceptor
Installation Instructions Road Defender Push Bumper Part # 5039-2L51 2013-2015 Ford Sedan Police Interceptor Do not attempt to install this product on any vehicle other than the one listed above! Parts
More informationUp-Armored HMMWV CASEVAC Conversion Kit (UAH-CCK)
M1114 Up-Armored HMMWV CASEVAC Conversion Kit (UAH-CCK) Operation Performance Measures Place CCK Into Operation Task: Conditions & Standard (1) Given one UAH with CCK installed and stored. (2) Two trained
More informationFlexJet - Flex Cable Replacement
P/N: 109515R0 14140 NE 200th St. Woodinville, WA. 98072 PH: (425) 398-8282 FX: (425) 398-8383 FlexJet - Flex Cable Replacement Notices: Warning! Ensure that all AC power cables are removed from the printer
More informationMustang Classic LightBar Instructions
1994-2004 Mustang Classic LightBar Instructions Note: Read installation instructions before starting. Component List: 1 LightBar 4 Poly Plugs 4 LightBar Bolts 4 LightBar Washers 2 LightBar Rivets 2 Light
More information67 [ ] OR [ ] REAR BRACKETS BARS Shocks Includes: Includes: Includes: Includes:
1967-1969 Firebird Mini Tub 4-Link Install Instructions 1-866-925-1101 www.totalcostinvolved.com CHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST BEFORE INSTALLATING OF THE KIT. IF ANY PIECES ARE
More informationTusk UTV Horn & Signal Kit Installation Instructions
Tusk UTV Horn & Signal Kit Installation Instructions The Tusk UTV signal kit is designed to be a simple way to provide front and rear turn signals, license plate mount with light, horn, and rearview mirrors
More informationREAD AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLATION OF SYSTEM AND OPERATION OF VEHICLE.
#9378 Installation Instructions 3 Body Lift Kit 1998-2000 Ranger READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLATION OF SYSTEM AND OPERATION OF VEHICLE. SAFETY WARNING BDS Suspension
More informationINSTALLATION INSTRUCTIONS AND PARTS LIST
INSTALLATION INSTRUCTIONS AND PARTS LIST VEHICLE APPLICATION: MODEL: 251123 (12 X 23 ) & 251120 (12 X 20 ) FRONT OR REAR MUDGUARDS 2008 AND NEWER FORD SUPER DUTY SINGLE WHEEL TRUCKS 1. READ INSTRUCTIONS
More informationNISSAN #2744. Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY
NISSAN 16K Industry Standard Rail Custom Mounting Kit #2744 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationINSTALLATION INSTRUCTIONS
Read instructions fully before commencing fitment. Left hand & Right hand components are determined as seated in the vehicle. Check for (& remove) any build up in all captive nuts fitted to the Bumper.
More informationInstallation instruction do88 Intercooler for SAAB 9-3 1,9 TTiD
Installation instruction do88 Intercooler for SAAB 9-3 1,9 TTiD This instruction shows how to replace the OEM intercooler with this performance intercooler. At this type of installation we always recommend
More informationB4578BTPA Fender Mounting Instructions for MIN4000, MIN900, MIN1500 & MIN1554 Fenders
STEP 1 B4578BTPA Fender Mounting Instructions for MIN4000, MIN900, MIN1500 & MIN1554 Fenders A. Unpack all cartons and lay out parts. B. Compare the parts with hardware kit B4578BTPA as shown in Figure
More informationPlease read the operator manual carefully and make sure you understand the instructions before using the machine.
967327801-00 Parts Zero Manual Turn Mower Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support in service
More information3 October 2016 PN# V Dodge Twin Turbo Kit (I-00274) ½ D o d g e 2 4 v I S B
3 October 2016 PN#1045320 24V Dodge Twin Turbo Kit (I-00274) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Twin Turbo Kit 1998½- 2 0 0 2 D o d g e 2 4 v I S B Part# 1045320 PLEASE READ
More informationRT1 SLIP-ON EXHAUST HONDA CBR600RR REV. A
08-50-43733 REV. A PARTS INCLUDED Ref. Part Number Description Qty 1) 00-200-00064 Slip-on S-bend Assembly 1 2) 00-200-00088 RT1 Aluminum Muffler Assembly 1 3) 03-46-43058 Muffler Mounting Strap 1 4) 07-27-42566
More informationDODGE DAKOTA 3 KIT INSTALLATION INSTRUCTIONS KIT# 60043
DODGE DAKOTA 3 KIT INSTALLATION INSTRUCTIONS 2000-2002 KIT# 60043 Installation of a Performance Automotive Group body lift kit will change the vehicle s center of gravity and handling characteristics both
More informationELECTRIC START KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6. All Polaris Pro-Ride Snowmobiles
ELECTRIC START KIT P/N 2879330 APPLICATION All Polaris Pro-Ride Snowmobiles BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationCamaro Torque Arm Install Instructions
1967-1969 Camaro Torque Arm Install Instructions 1-800-984-6259 www.totalcostinvolved.com 67 [429-4202-00] OR 68-69 [429-4202-00] REAR BRACKETS BARS Shocks Includes: Includes: Includes: Includes: 1 REAR
More informationInstallation Guide 4097M
Installation Guide 4097M Kargo Master Rancho Cordova, CA 95742 800 343 7486 CustomerService@KargoMaster.com DATE: Installation Instructions 4097M *PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING,
More information2015 Ford F150 Rear Bumper w/ LED
2015 Ford F150 Bumper w/ LED T527990 T527991 PARTS LIST: 1 Bumper Assembly 4 12mm Lock Washers 2 Mounting Brackets 6 12 mm Nylon Lock Nuts 4 Sensor Hole Plugs 8 4mm x 10mm Button Head Bolts 2 Plastic Plugs
More informationSafe-T-element Installation Instructions
Safe-T-element Installation Instructions For: PTI STEZA (2x2 Burner Configuration) & PTI STEZB (3x1 Burner Configuration) Revision K (May. 3 2012) TABLE OF CONTENTS 1. PREPARATION... 3 1.1 General Safety
More informationILLUSTRATED PARTS LIST
LM700 INDEPENDENT REAR SUSPENSION WITH 653cc SUBARU ENGINE 800-643-7332 amsportworks.com NOTE: Some part numbers vary by serial number. The serial number is located on a brass tag beneath the dump bed
More information