model H with1920

Transcription

1 model with1920 ADA Compliant Chilled Dual Wall-Mount Fountain and Bottle Filler FEATUES & BENEFITS CONSTUCTION 18-gauge Type 304 stainless steel swirl design bowl, 14-gauge Type 304 stainless steel bracket, and vandal-resistant bottom plate provide a long lasting unit. BOTTLE FILLE Vandal-resistant, 14-gauge Type 304 stainless steel bottle fi ller housing with push button operation using the same all stainless steel valve with front access serviceability used in Haws drinking fountains. PUSH BUTTON VALVE The push-button activated valve assembly allows for front access stream adjustment as well as cartridge and strainer access. The valve works at an operating pressure range of 30 to 90 psi (2.1 to 6.2 bar). BUBBLE HEAD Polished chrome-plated brass bubbler head with integral laminar fl ow prevents splashing while providing a superior fl ow pattern. The integral basin shank and inserted roll pin add vandal resistance strength. Shielded, angled stream opening provides a steady, sanitary source of drinking water at.45 gpm. Heavy-duty galvanized steel mounting frame provides the sturdy hidden support needed for the Hi-Lo confi guration of this unit. Further convenience is given to the chiller with the integral fold-out shelf. QUALITY CONTOL Both fountains and bottle fi ller are pre-built and fully water and pressure tested to ensure proper functionality. SPECIFICATIONS Model with 1920: ADA compliant Hi-Lo wall-mounted, drinking fountain and bottle fi ller with push button operation. Fountains shall include dual 18-gauge Type 304 Stainless Steel satin fi nish basins with integral swirl design, polished chromeplated brass vandal resistant bubbler heads with integral laminar anti-squirt fl ow, chrome-plated brass vandal-resistant waste strainers, stainless steel satin fi nish back panel and louvered intrusion-proof grill. high and low fountain mounting levels, and 1-1/4 O.D. (3.2 cm) waste pipes. Fountains and bottle fi ller use 100% lead-free waterways, push-button operated stainless steel valves with front accessible cartridge and fl ow adjustment, 14-gauge Type 304 Stainless Steel wall brackets (polished stainless surfaces on model HPS), and vandal-resistant bottom plates. The -134a refrigeration system is hermetically sealed and delivers a minimum of 8 gph (30.3 L) of water at 50 F (10 C), 115 Volts, 60Hz, rated watts: 370, full load amps: 5. CSA certifi ed and ADA accessible, ANSI/NSF 61, Section 9, lead free. Haws electric water coolers comply with AI Standard 1010 and ANSI A117.1, and are listed by Underwriter Laboratories to U.S. and Canadian standards. MODEL CHOICES / BP32 / 1920 / MTGF.LG / HC8 Model fountain with stainless steel back plate, bottle fi ller, mounting frame, and chiller. / BP32 / 1920 / MTGF.LG / HC8 Model fountain with stainless steel back plate, bottle fi ller, reverse mounting frame, and chiller. HO / BP32 / 1920 / MTGF.LG / HC8 Model HO, sensor-operated fountain with stainless steel back plate, bottle fi ller, mounting frame, and chiller. HO / BP32 / 1920 / MTGF.LG / HC8 Model HO, sensor-operated fountain with stainless steel back plate, bottle fi ller, reverse mounting frame, and chiller. HPS / BP32HPS / 1920HPS / MTGF.LG / HC8 Model fountain with high-polish stainless steel back plate, high-polish stainless steel bottle fi ller, mounting frame, and chiller. OPTIONS Mounting Plate: Model L, in-wall mounting plate for model 1920 over low side of dual drinking fountains. Mounting Plate: Model 6700, on-wall mounting plate for 1920 series bottle fi llers, single or dual fountain retrofi t installations Kleppe Lane :: Sparks, NV :: p :: f :: e. info@hawsco.com ::

2 THIS DOCUMENT IS TUE AND COECT AT TIME OF PUBLICATION. CONTINUED PODUCT IMPOVEMENTS MAKE SPECIFICATIONS AND MEASUEMENTS SUBJECT TO CHANGE WITHOUT NOTICE. NOTES: 1. HOLD OUGH-IN DIMENSIONS ±1/8" (3.2mm). 16" 406mm 2. WHEN INSTALLING THIS UNIT, LOCAL, STATE, O FEDEAL CODES SHOULD BE ADHEED TO. FO DIMENSIONS (LOCATIONS), WASTE AND SUPPLY EQUIEMENTS OTHE THAN SHOWN, DIMENSIONS MAKED () MUST BE ADJUSTED ACCODINGLY. 3. INSTALLE MUST POVIDE TAP FO POPE INSTALLATION. 4 EFE TO 5874SS OPEATION AND MAINTENANCE MANUAL FO PUSH BUTTON AND VALVE INSTALLATION/MAINTENANCE INSTUCTIONS. 5 EFE TO MTGF.LG INSTALLATION DAWING FO OUGH-IN DIMENSIONS. 1/2" 12.7mm 6 INSET 5/16"-18 PANEL INSETS FOM OPPOSITE SIDE AT LOCATONS SHOWN BY DAKENED HOLES. HOLE COMBINATIONS SHOWN AE FO USE WITH LOW FOUNTIAN ON THE IGHT AND THE HI FOUNTAIN ON THE LEFT. USE OPPOSITE HOLES FO HI ON IGHT AND LOW ON LEFT. 7 HOLE COMBINATION SHOWN BELOW IS FO USE WITH LOW FOUNTAIN ON THE IGHT AND HIGH FOUNTAIN ON THE LEFT. USE OPPOSITE HOLES FO HIGH ON IGHT AND LOW ON LEFT. 8 TO CHANGE FOUNTAIN MTG. SCEW LOCATIONS: FIST EMOVE SCEWS AND THEN SQUEEZE CLIPS ON NUT ETAINE TO POP OUT. SNAP INTO NEW POSITIONS AND E-ASSEMBLE SCEWS. 9 IMPOTANT: A L.H. LOW (OPTIONAL) CONFIGUATION WILL EQUIE A DIFFEENT BACK PANEL AND THE WASTE AND SUPPLY DIMENSIONS SHOWN () MUST BE EVESED. 10 ALIGN HOLES IN CHILLE SUPPOT TAY WITH HOLES IN AND FASTEN WITH #10 SHEET METAL SCEWS. Ø 14-1/8" 359mm 4 BACK PANEL 31-1/8" 791mm OUGH-IN 32" 812.8mm 5/8" 16mm EMOVE VALVE FOM PUSH BUTTON TO INSTALL WASTE ELBOW ONTO BOWL. AFTE WASTE ELBOW IS INSTALLED, EINSTALL VALVE & ADJUST FLOW 12" CLEAANCE 305mm 4" 101.6mm WIDTH 18-5/8" 473mm 3" 76mm WALL FACE FLANGE BACK PANEL WASTE BENDS (NOT SUPPLIED) SUPPLY STOP & 3/8" O.D. TUBING (NOT SUPPLIED) 1-1/4" IPS TAPS (NOT SUPPLIED) IMPOTANT: MUST BE INSTALLED SO THAT FLANGE BUTTS AGAINST FINISHED WALL FACE. 3/8" OD TUBING, INSULATION, TEE & FITTING GILLE CLIP 1-1/2" 38.1mm 37-5/8" 39-1/4" 956mm OUGH-IN 997mm INLINE STAINE, 1/4" OD TUBE X 3/8" OD TUBE INLET 39 5/32" 991mm 34 5/32" 864mm 32" 812mm 27" 686mm 1-1/4" O.D. WASTE BEND MTGF.LG FLOO LINE /16" 729mm FOUNTAIN SUPPLY 32-7/8" 27-7/8" 835mm 708mm FOUNTAIN WASTE FOUNTAIN WASTE 33-11/16" 856mm FOUNTAIN SUPPLY GILLE MACHINE SCEW SHEET METAL SCEW CLIP INSIDE OF 2-1/4" 57mm 5 ELECTICAL ACCESS CHILLE SUPPOT TAY SCEW 8 BOWL PATTEN DETAIL 2016 ECN NO. EVISED PE BY: ECN: 5142 CJC DAWN: DATE: CHK'D.: /HPS EVISION TM 07/97 VWC APPOVED: DATE: DINKING FOUNTAIN 19 FV 10/24/16 SCALE: 1/18 DAWING TYPE: INSTALLATION SIZE: A SHEET 1 OF 1 C Haws Corporation - All ights eserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation D

3 - - THIS DOCUMENT IS TUE AND COECT AT TIME OF PUBLICATION. CONTINUED PODUCT IMPOVEMENTS MAKE SPECIFICATIONS AND MEASUEMENTS SUBJECT TO CHANGE WITHOUT NOTICE L PLATE (BEHIND FINISH WALL) - O ETOFIT PLATE (ON TOP OF FINISH WALL) 1920/1920HPS BP32/BP32HPS (IF FOUNTAIN HIGH/LOW SIDES AE EVESED USE BP32) INSTALLATION ABOVE HAWS, HO, HPS IF YOU FOUNTAIN IS THIS STYLE USE THESE DIMENSIONS 3/8" PUSH IN TEE (CONNECT TO FOUNTAIN SUPPLY) 1. SEE SEPAATE INSTALLATION DAWINGS FO AND BACKPANELS 2. WHEN INSTALLING THIS UNIT, LOCAL, STATE O FEDEAL CODES SHOULD BE ADHEED TO FO INSTALLATION LOCATIONS, WASTE & SUPPLY EQUIEMENTS OTHE THAN SHOWN. C ECN NO. EVISED PE BY: ECN: GC -20 DAWN: DATE: CHK'D.: MODEL, HPS AND HO EVISION GC 05/31/17 APPOVED: DATE: WITH MODEL 1920 BOTTLE FILLE 0A.1 SCALE: N/A DAWING TYPE: INSTALLATION SIZE: A SHEET 1 OF Haws Corporation - All ights eserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. 1 of 1

4 THIS DOCUMENT IS TUE AND COECT AT TIME OF PUBLICATION. CONTINUED PODUCT IMPOVEMENTS MAKE SPECIFICATIONS AND MEASUEMENTS SUBJECT TO CHANGE WITHOUT NOTICE HOLE LOCATIONS NOTES: 1. C SEE SEPEATE INSTALLATION DAWINGS FO PLATES AND BACKPANELS 2. WHEN INSTALLING THIS UNIT, LOCAL, STATE O FEDEAL CODES SHOULD BE ADHEED TO FO INSTALLATION LOCATIONS, WASTE & SUPPLY EQUIEMENTS OTHE THAN SHOWN. ECN NO. EVISED PE BY: 5081 ECN: 5172 MJ DAWN: DATE: CHK'D.: MODEL 1920/1920HPS/1920W EVISION DS 05/25/16 FV APPOVED: DATE: 2 FV 02/27/17 SCALE: N/A DAWING TYPE: INSTALLATION SIZE: A SHEET 1 OF Haws Corporation - All ights eserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation D

5 THIS DOCUMENT IS TUE AND COECT AT TIME OF PUBLICATION. CONTINUED PODUCT IMPOVEMENTS MAKE SPECIFICATIONS AND MEASUEMENTS SUBJECT TO CHANGE WITHOUT NOTICE. STEP 1 ATTACH SUPPLIED BACKET TO WALL USING APPOPIATE FASTENES. BACKET IS INSTALLED OVE THE HIGH-SIDE OF THE DINKING FOUNTAIN MODEL 1920 ADHESIVE SIDE MODEL BP32 / BP32HPS MODEL 1920 STEP 2 PLACE THE BACKPLATE AGAINST THE WALL AND SLIDE SIDEWAYS SO THE TABS CATCH UNDE THE BACKET 8 SPACES (2 PE BOLT IF THE PLATE IS INSTALLED BEHIND THE FINISHED WALL. USE 1 SPACE PE BOLT FO ETOFITS WHEE THE PLATE IS INSTALLED IN FONT OF THE FINISHED WALL) MODEL BP32L C STEP 3 INSTALL THE BOTTLE FILLE PE THE INSTUCTIONS SUPPLIED WITH THE UNIT NOTES: 1. WHEN INSTALLING THIS UNIT, LOCAL, STATE O FEDEAL CODES SHOULD BE ADHEED TO. INSTALLATION OVE DOUBLE FOUNTAIN SHOWN FOM EA ECN NO. EVISED PE BY: 5081 ECN: 5172 MJ DAWN: DATE: CHK'D.: DAWING, BACK PANEL SPACE INST, BF EVISION MJ 02/02/17 FV APPOVED: DATE: 2 FV 02/27/17 SCALE: 1:1 DAWING TYPE: INSTALLATION SIZE: A SHEET 2 OF Haws Corporation - All ights eserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation D

6

7 C 2006 Haws Corporation - All ights eserved HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. A B IF YOU FOUNTAIN IS THIS STYLE USE THESE DIMENSIONS INSTALLATION CHILLE ELECTICAL INSTALLATION A B IF YOU FOUNTAIN IS THIS STYLE USE THESE DIMENSIONS A (SEE FOUNTAIN STYLE) B (SEE FOUNTAIN STYLE) BOWL PATTEN DETAIL MUST BE INSTALLED SO THAT LIP OF OVELAPS & BUTTS UP AGAINST FINISHED WALL Page 1 of 1