UNIVERSAL MAGNETIC FIELD SENSORS FOR PNEUMATIC CYLINDERS. Sense it! Connect it! Bus it! Solve it!

Transcription

1 UNIVERSAL MAGNETIC FIELD SENSORS FOR PNEUMATIC CYLINDERS Sense it! Connect it! Bus it! Solve it!

2 UNIVERSAL MAGNETIC FIELD SENSORS FOR PNEUMATIC CYLINDE The position detection of piston on all standard pneumatic cylinders can now easily be implemented with a single sensor type. But what s more, the new magnetic field sensor BIM-UN TURCK not only supports efficient standardization but also provides an enormous potential for optimization. This implies requirements related to construction, over purchase and production, up to system operators and maintenance: Use the unique performance spectrum of this sensor for effec cost reduction concerning your application! Reliable mounting A pre-fixing lip enables one-hand mounting in the T groove. The sensor can already be adjusted in the groove and fixated vibrationresistant with a screw. The fixation of the screw near the cable routing prevents an uplift of the sensor when pulling the cable. Stable mounting The sensor is mou the T groove with type of wing screw wing screw, made steel alloy, is extre stable. For vibratio tant mounting it is enough to tighten with a quarter turn a standard screw 1. mm Allen key.

3 RS T by High system availability The new sensors provide high operational reliability even in rough production environments. A high level of EMC, degree of protection IP7 and especially the safe mounting of the sensors are a guaranty for it. The prior aim during the mechanical design process was to create a housing with robust mounting elements, which would perfectly suit all conditions of application. This way the new BIM-UNT magnetic field sensors withstand the rough conditions of mechanical engineering. Use these advantages to optimize your production processes: Less downtimes : A robust fi xing screw made of tool steel ensure stable mounting. Low risk of damages: An optimized cable exit and an optimally placed screw avoid damages when pulling the cable. Short down-times: Spare parts are available on short notice and at low costs. Efficient standardization The new magnetic field sensor BIM-UNT enables the detection of piston on all standard pneumatic cylinders. An intelligently streamlined product line quickly pays off for you. The new advantages: One sensor type for all cylinders. The sensor can be mounted directly on the T groove cylinder and special accessories are available for the mounting on round, tie-rod or dovetail cylinders. Even special versions, e.g. w fi ne adjustment or external fi x tion of the switching point ar longer necessary. If required, cost-effi cient mounting of th accessories on the standard sensor is possible. Low average prices because there is no need for special devices. all tive High interference immunity due to excellent level of EMC: The BIM- UNT already fulfi ls the strict provisions of future standards. nted in a new. The of tool mely n-resissimply the screw by using driver or a Compact housing style With a total length of only 28 mm the BIM-UNT is one of the most compact sensors on the market. The active face is located directly at the sensor end. Thus a secure detection of the piston rod up to the end postion even at compact short stroke cylinders is possible. Perfectly visible Thanks to a brigh all-round visible L current switching is perfectly visible any perspective. advantage in cas sensors are align mounted. Thus th position can be d

4 Extremely service-friendly The new BIM-UNT magnetic field sensor is extremely flexible and user-friendly with respect to mounting and adjustment. Remarkable advantages for the system operator are thus provided. These advantages pay off for you: Simple mounting together with optimal adjustment and fi ne tuning. Maximum freedom Owing to versatile connection possibilities, simple mounting and the availability of flexibly deployable accessories, the new sensor provides maximum planning freedom while minimising the mounting efforts. All advantages for you at a glance: Versatile solutions are feasible with only a few device types. Reduced mounting effort due to flexibly applicable mounting accessories. Simple linkage supported by a variable connection concept. Quick mounting by a prefixing lip and tightening of the screw with only a quarter turn. Quick replacement due to simple recovery of the original switching point. Maximum freedom provided for construction ith a- e no Minimum maintenance effort due to a reduced variety of sensor types ese t and ED, the status from This is of es where ed while e best etermined. MR sensor element Due to a novel MR sensor element all standard magnets in pneumatic cylinders can be detected safely and without multiple switching points. Thus exact position detection is possible, even in end postions and you can benefit from the high level of flexibility. High level of EMC The BIM-UNT not only fulfils the currently valid standard EN , but also exceeds the strict provisions of the coming amendment (including tests according to EN conducted interference ).

5 UNIVERSAL MAGNETIC FIELD SENSORS FOR PNEUMATIC CYLINDERS Mounting and adjustment accessories for the BIM-UNT... Dimension drawings Type Ident no. Short description ø 7 M3 1 ø, UNT-Justage 4870 Accessory for adjustment of the switching point, snap-fi t mounting in the accessory groove of the sensor, suited for multiple usage. M3, , M3 3, UNT-Stopper 4871 Accessory for securing the switching point on the T groove cylinder, snap-fi t mounting in the accessory groove of the sensor.,4 18, 14,1 14, 31,2 8,3 20,9 KLR-UNT Accessory for mounting on a round cylinder, diameter mm KLR-UNT Accessory for mounting on a round cylinder, diameter mm KLDT-UNT Accessory for mounting on a dovetail cylinder groove width 7 mm KLDT-UNT Accessory for mounting on a dovetail cylinder groove width 9.4 mm KLDT-UNT Accessory for mounting on a dovetail cylinder groove width 11. mm KLDT-UNT Accessory for mounting on a dovetail cylinder groove width 12. mm KLZ1-INT Accessory for mounting on a tie-rod cylinder, diameter mm KLZ2-INT Accessory for mounting on a tie-rod cylinder, diameter 0 3 mm KLZ3-INT Accessory for mounting on a tie-rod cylinder, diameter mm no drawing INT CABLE CLIP 9004 Cable clip for fi xation of the cable in the T groove, packing unit = 10 pieces (one piece included in the scope of delivery BIM-UNT) Optional Accessories A broad ranged program of accessories completes the performance spectrum of the new BIM-UNT magnetic field sensors. Part of the program are e.g. the accessories for the mounting on all standard cylinder types, adjustment and fixation, as well as the clips for safe cable routing.

6 UNIVERSAL MAGNETIC FIELD SENSORS FOR PNEUMATIC CYLINDERS BIM-UNT: Types and technical data Dimension drawings Type / Connection / Ident. no. wiring diagram 0, BIM-UNT-APX PUR-cable, 2 m BIM-UNT-APX 7M PUR-cable, 7 m BN BU BK 0, BIM-UNT-APX-0,3-PSG3S Pigtail M8 x 1, snap-lock / fi xed thread, 0.3 m PUR-cable M8 x 1 1 BN 3 BU 0, 3 BIM-UNT-APX-0,3-PSG3M Pigtail M8 x 1, threaded coupling nut 0.3 m PUR-cable BIM-UNT-APX-0,-PSG3M Pigtail M8 x threaded coupling nut 0. m PUR-cable 4 BK M8 x 1 1 BN 3 BU 41,2 4 BK 0, BIM-UNT-APX-0,3-RS4 Pigtail M12 x threaded coupling nut 0.3 m PUR-cable M12 x 1 3 BU 4 BK 48, Technical data Ambient temperature C Operating voltage VDC Ripple Vpp 10 % Upp Rated operating current DC 10 ma No-load current Io 1 ma Off-state current 0.1 ma Switching frequency 1 khz Output function 3-wire, normally open, PNP Short-circuit protection yes/cyclic Voltage drop Ie 1.8 V Wire-break / reverse polarity protection yes / completely Vibration resistance Hz (1 mm) Shock resistance 30 g (11 ms) Degree of protection IP7 Overtravel speed 10 m/s 1 BN Hans Turck GmbH & Co. KG Witzlebenstraße Mülheim an der Ruhr Germany Tel. 49 (0) Fax 49 (0) more@turck.com Internet D *D1013ßß008*